- Computers & electronics
- Print & Scan
- Printing supplies
- Printer cleaning
- Posiflex
- PD2100S/XX
- User manual
advertisement
PD- Series
2200
USER’S MANUAL
VFD CUSTOMER DISPLAY for
ALPHANUMERICAL DISPLAY in 2 x 20 format
Rev. : B4
SOME IMPORTANT NOTES
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the VFD customer display PD-2100 and PD-
2200 series. Both series provide versatile font formats and support various instruction sets.
These series of products receive instructions in serial communication protocols and is capable of entering pass through mode for PD-2200 so that all instructions received pass on to next connected serial device if properly configured.
The manufacturer of the PD-2100 and PD-2200 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw, http: //www.posiflexuk.com, http://www.posiflexusa.com.
Copyright Posiflex Inc. 2005
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Mustek Corp..
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
P/N: 19410900040
TABLE OF CONTENTS
FEATURES
· · · · · · · · · · · · · · · · · · · · · · · · 1 - 1
MODEL NUMBERS
· · · · · · · · · · · · · · · · · · 2 - 1
CARTON CONTENTS
· · · · · · · · · · · · · · · · 3 - 1
INSTALLATION
· · · · · · · · · · · · · · · · · · · · 4 - 1
Signal Connection · · · · · · · · · · · · · · · · · · · · · · 4 - 1
For PD2100S/XX Series · · · · · · · · · · · · · · · · · · · 4
- 1
For PD2200B/XX Series · · · · · · · · · · · · · · · · · · 4
- 1
Power Connection & Mounting · · · · · · · · · · · · · · · · 4 - 1
Using Power Adaptor · · · · · · · · · · · · · · · · · · · 4 - 1
Using Power from PC · · · · · · · · · · · · · · · · · · · 4
- 2
Using Power from POS System · · · · · · · · · · · · · · · 4
- 3
Using printer power adaptor · · · · · · · · · · · · ·· · ·· 4
- 4
After Powering Up · · · · · · · · · · · · · · · · · · · · · · 4 - 4
MECHANICAL FEATURES
· · · · · · · · · · · · 5 - 1
Dimension Drawings · · · · · · · · · · · · · · · · · · · · · 5 - 1
Display Frame Common Features · · · · · · · · · · · · · · · 5 - 2
Cushion Against Shock · · · · · · · · · · · · · · · · · · · · 5 - 2
Stand - Plate · · · · · · · · · · · · · · · · · · · · · · · · · 5 - 2
COMMAND EMULATION
· · · · · · · · · · · · · 6 - 1
SPECIFICATIONS
· · · · · · · · · · · · · · · · · · · 7 - 1
Optical · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7 - 1
Mechanical · · · · · · · · · · · · · · · · · · · · · · · · · · 7 - 1
Electrical · · · · · · · · · · · · · · · · · · · · · · · · · · · 7 - 1
Environmental · · · · · · · · · · · · · · · · · · · · · · · · 7 - 1
i
I. FEATURES
• Bright vacuum fluorescent display
• Two-line display with 20 characters per line
• Large characters for easy viewing (11.25mm by 7.2mm)
• Long life and trouble free operation
• Secure construction with bumper best for screw on operation in
PD2100 series. Generous base best for freely stand alone application in PD2200 series.
• Two adjustable viewing angles
• Pole height adjustable
• Display frame is horizontally slidable, and 360° rotatable freely
• Brightness adjustable by software
• Simple installation
• Direct interface connection with computers and peripherals
• Standard Serial Interface for both series and with pass through capability for PD2200 series.
• Multiple choices for power supply source.
• Supported in the code pages include PC437, Katakana, PC850
Multilingual, PC860 Portuguese, PC863 Canadian French, PC865
Nordic, Russia, Albic, PC437G Greek, W1257 Baltic, W1253
Greek and PC858 the code page contains Euro dollar sign at position D5h.
1 - 1
Model
Case
Color
Display Power
Color Source
PD2100S Ivory
Green
PD2100S/C Charcoal
PD2100S/D Ivory
Blue
PD2100S/F Charcoal
Kit
PD2100S/XX Ivory
PD2100S/XX/C Charcoal
Green
PD2100S/XX/D Ivory
PD2100S/XX/F Charcoal
Blue
Adaptor
(+12V AC)
Base Connector
Pass
Through
Small DIN 5 pin N. A.
PD2200B Ivory
Green
PD2200B/C Charcoal
PD2200B/D Ivory
Blue
PD2200B/F Charcoal
PD2200B/XX
PD2200B/XX/C Charcoal
PD2200B/XX/D Ivory
PD2200B/XX/F
Ivory
Green
Charcoal Blue
Adaptor
(+12V AC)/
Large
*Share from printer
DB9 F+M
/ 3 pin jack from printer adaptor
(+24V DC)
Yes
PD2201 Ivory
Green
PD2201/C Charcoal + 5 V DC in connector
PST 10 pin RJ Yes
PD2201/D Ivory
Blue
PD2201/F Charcoal
Note:
1. For “/XX” models, “/XX” should be replaced by the country code for the power plug type of the power adaptor such as “/US” or “/UK” etc. and the power to display unit is 12V AC. For models without “/XX”, the power used is + 12 V DC from PC through a power kit.
2. In “Base”: Small is 80 x 60 x 51(mm), Large is 220 x 110 x 41 (mm) and
PST means option device in PST system.
3. The “*” mark means the power source shared from the printer power adaptor by means of a cable and is applicable in version Cxa / Dxa onwards only.
2 - 1
1. Pole display, pre-assembled
3. Metal stand plate with mounting screws (for PD2100S series only).
4. One interface cable 20863012510 (CCBLA - 125A) for PD2100S series or
20863137210 (CCBLA-372) for PD2200B series
5. Power source (one of the four below):
Power supply: AC power adaptor specified per country type
Power kit incl. power supply cable (inside PC) 39212001000 (CCBLA-
141 on I/O plate) and power supply cable (to PD) 20863041100
(CCBLA-411)
Combined in the signal cable mentioned above when the PD is connected to a Posiflex POS system
Power cable (20863250900) to share from printer power adaptor
3 - 1
IV. INSTALLATION
A. Signal connection
1. For PD2100S Series
1. Take off the metal plate on the Pole display base cabinet by loosening the screws.
2. Connect the DIN 5 pin plug of the cable
CCBLA - 125A to the female
DIN 5 pin jack inside the base
DIN jack cabinet and connect the DB9 connector of cable CCBLA -
125A to serial port COM1 or
COM2 of the computer.
To COM port
DIN plug
2. For PD2200B Series
Connect the DB9 female connector of the signal cable CCBLA - 372 to the COM port of PC and connect the DB9 male connector of the signal cable
CCBLA – 372 to the DB9 female connector in the base of the PD.
3. For PD2201 Series
Follow the pole display installation instruction of the PST series. No external power connection beyond the power arrangement in COM port of PST system is required.
B. Power connection & Mounting
1. Using power from AC adaptor
for /xx models
Always check the specification of the power adaptor against the power socket before making any connection.
Always keep the insertion of the power adaptor into the power socket
DC Jack From Power
Adaptor
DC Plug
4 - 1
as the very last step of the whole installation procedure. Connect the 2.5
φ/5.5φ
DC plug of the AC adapter to the 2.5
φ/5.5φ DC jack inside or at bottom of the base cabinet. The above drawing shows the example in PD2100 series. For
PD2200 series, you may now place the base on a horizontal surface and prepare to power on. However, some mounting operations are
Base cabinet applicable to PD2100 series:
Stand plate
1. Put the metal plate back and fix the screws.
2. Mount the pole display stand plate to the metal plate of base cabinet with screws and mount the pole display stand plate to your
Posiflex cash drawer (CR310X or CR320X) or on the cashier’s dash.
3. Plug the adapter into power outlet.
Bottom view of cash drawer
2. Using power from PC
for models with power kit
4 pin Telephone
Jack
I/O Plate of
CCBLA-141
Switching Power
Supply Unit
Install the cable
CCBLA-141 with I/O plate in the power kit into the hosting PC for obtaining
DC power as shown in the left drawing. However, it is absolutely important to
turn all the power off before removing any case or connecting any cable.
Followings are step-by-step
CCBLA-141
4 pin Power connector
Inside view of example PC instructions for installing this cable.
1. Make sure the PC to supply power is turned off.
2. Open the case of PC according to its relevant manual.
3. Select one I/O plate position on rear window of PC to install the I/O plate of CCBLA-141.
4. Select one set of large 4 pin connector from the switching power supply unit of PC and connect the male 4 pin connector of CCBLA-
141 to the connector from power supply. Connect the female 4 pin
4 - 2
connector of CCBLA-141 to the I/O device of PC such as a HDD if necessary.
5. Assemble the case of PC back.
Then referring to drawing below to complete the basic power and signal cabling. Note the PC should remain OFF during the connection.
9 pin D connector of CCBLA-372
COM port (9 pin serial port)
4 pin Telephone jack of CCBLA-141
Both to bottom of PD
4 pin Telephone plug of CCBLA-411 Rear side of PC
1. Connect the 4 pin telephone plug of CCBLA-411 to the 4 pin telephone jack on the I/O plate of CCBLA-141 which has been mounted as described above.
2. Insert the DC plug of CCBLA-411 into the jack at the bottom of the base of PD in the same way as the power adaptor. Let the cables come out of the bottom of PD2200 series through the opening at the back of base so that the PD can stand securely.
3. Now the user may turn on the PC (and the PD when it is PD2200 series) for application unless the user wants to use PD for pass through purpose (PD2200 series only).
3. Using power from POS system
for PD2201 series
This super convenient power supply method applies only to PD2201 when installed in a Posiflex PST POS system or PD2200B when connected to a
Posiflex POS system after proper setting for power in COM port. The power connection is already done when the signal connection is completed.
4 - 3
4. Using printer power adaptor
for PD2200B series
Posiflex POS printer
+24 V DC
PD2200B
+24 V DC Out
+24 V DC In
Posiflex POS
Printer Power
Adaptor (24 V DC)
Power Cable
The PD2200B series can also be powered by the power adaptor supporting a Posiflex POS printer by using a separately purchased specific power cable (P/N: 20863250900). Follow steps below:
1. Check that the (+24 V DC) power adaptor plug matches the power socket. But please always keep the insertion of the power adaptor into the power socket as the very last step of the whole installation procedure.
2. Insert the 3 pin power connector from the +24 V DC power adaptor to the “+24 V DC In” jack in the connector area. Be sure to hear a click to obtain a firm contact.
3. Insert either end of the power cable (20863250900) to “+24 V DC
Out” jack in the connector area and insert the other end to the power connector of Posiflex POS printer if needed. Be sure to hear a click at each connection to obtain a firm contact.
4. Now place the base on a horizontal surface and prepare to power on.
5. Please note that when DC power connection is used, there must be no
AC power connection at the bottom of the base cabinet on the PD2200.
C. After Powering Up
A firmware version as power on sign will appear for a while and the emulation mode will appear for a while after the firmware version display. Then a blinking block-shaped cursor will appear at the left-most digit of the top row for Noritake or Futaba emulation mode and no cursor will appear for other emulation modes. The installation is now completed.
4 - 4
A. Dimension Drawings
70.0
260.0
219.0
34.0 70.0 70.0
60.3
36.8
70.0
180.0
(Lowest height)
180.0
135.0
Stroke
135.0
315.0
(Max. height)
51.0
2.6
76.0
80.0
51.0
2.6
60.0 114.0
70.0
180.0
(Lowest height)
41.0
260.0
219.0
220.0
PD2100 Series
34.0
70.0
70.0
60.3
36.8
180.0
135.0
Stroke
41.0
110.0
PD2200 Series
70.0
135.0
315.0
41.0
(Max. height)
5 - 1
B. Display Frame Common Features
In addition to the above drawings given, both the PD2100/PD2200 series are delicately designed to have in common the following user-friendly mechanical features for most up-to-date store management systems.
Button switch
The display panel of PD2100/PD2200 series can be moved or rotated/tilted both vertically and horizontally
The overall pole height can be adjusted freely by pulling the button switch and match it to one of the concave cavities on inner pole at a proper height. Overall height of PD2100 series is adjustable from 309mm to 444mm and overall height of PD2200 series is adjustable from 291mm to 426mm.
The display frame can be slid left-and-right-wise for a total sliding distance of 100mm. It can also be rotated horizontally for almost 360 degree, however, the rotation is limited to within 360 degree to avoid the internal cable to be broken. It can further be tilted to offer 2 different viewing angles ---14.5
°,
30
° from the vertical position.
C. Cushion Against Shock
Coming from Any
Direction for PD2100 Series
Another special delicate design at bottom of PD2100S is a cushion mechanism to survive an inevitable crash or damage on pole display from certain absent - minded customers, playing children and so on. It will absorb any external stress or bump to avoid any damage of the device.
D. Stand - Plate
Accessory for PD2100 Series
The stand - plate accessory is designed to fix pole display device either on the desk with (or without) screws or at the bottom of CR3100/3200 series cash drawers.
5 - 2
VI. COMMAND EMULATION
This VFD customer display provides several software programming emulation modes for display control. The emulation mode is defined by adjusting
SW1 the DIP SW on the back as in the following table.
Switching these DIP switches may require some
Push up to switch on
SW2 proper tool or special effort. The switch positions must be changed only when power turned off. The relationship is tabulated below.
For PD2100:
Emulation Mode Futaba Noritake Aedex Epson
SW 1
SW 2
on off on off on on off off
For PD2200 and PD2201:
Emulation Mode UTC (/Futaba) Noritake Aedex (/ADM) Epson
SW 1
on off on off
SW 2
on on off off
The parenthesized Futaba and ADM modes can be accessible when the internal jumper JP3 is opened. The followings are some brief introduction of the emulation modes as they are compared to each other:
Cursor
Blinking
Block
Blinking
Block
Non-
N.A. N.A. displayable
Default mode
User defined font
Brightness control
N.A. 2 characters N.A. N.A. 2 characters
Pass through function
Leading code change YES YES YES
Timer clock NO NO NO NO YES
To display the Euro-dollar sign on the Euro code page supported models, please select code page 13(Hex) and display code D5(Hex). Please visit our web site http://www.posiflex.com.tw for details on software commands if required.
6 - 1
VII. SPECIFICATIONS
A. Optical
Number of digits
Dot matrix
Digit height
Digit width
Display color
B. Mechanical
Weight
Height
20 digits/row, 2 rows
5 X 7 dots
11.25 mm
7.2 mm
Blue or Green
0.7 kg (1.5 lbs)
309 ~ 444 mm (For PD2100 series)
291 ~ 426 mm (For PD2200 series)
Depth 60 mm (For PD2100 series)
110 mm (For PD2200 series)
C. Electrical
Power (Applied to adapter)
Input: 120VAC, 60 Hz or 220VAC, 50 Hz
Output:
Power from PC:
12VAC heavy duty, 1.2 A (min.)
+ 12VDC
Power from Posiflex POS system:
+ 5VDC (PD2201)
+ 12VDC (PD2200B)
D. Environmental
Operating temperature 0
° to + 40°C
Storage temperature -20
° to + 70°C
Shock 40 G
WARNING: If the user opens the pole display housing to make any change, all the product warranty will be voided.
7 - 1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project