Wi-Fi 6 MESH AP
Quick Start Guide
AX6600
Overview
Thank you for choosing our product.
Please read this manual before use.
If you need to change Internet Access method,i.e.from router to bridge mode,or add a new
Mesh AP to your Mesh network,or need other information,please scan the QR code below or visit https://azoresnetworks.com/pages/download-center in the browser to view the corresponding electronic user manual for instructions.
Scan QR code to download electronic user manual
2
01
Product Hardware Description
Product Backside Description
批注 [A1]: 需要替换 AX6600 两口的图片
Button Description
Button
WPS
Reset
ON/OFF
Function
Set the WPS process.
Short press (1 second) for reset the router;
Long press (5 seconds or longer) for reset to factory default settings.
Power on and off the router.
LED Description
LED Behavior
Dark
Steady Red
Blinking Red
Blinking Green
Scenario
No Power
Powering up
No network cable connected
Network connection in progress
3
Steady Green
Blinking Blue
Steady Blue
Function normally and can access the Internet
WPS or Mesh pairing in progress
Pairing successful
02
Product Manual
Single Router
For single router ：
Connect the provided network cable from the AX6600 Router to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway). Please refer to SINGLE ROUTER SETUP STEPS for network setup.
4
For mesh router set:
Main AP has the QR code on the backside,is used as the main router, which is to be connected, via provided network cable, to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway); Satellite AP is used for
Wi-Fi network expansion. Please refer to ONE ROUTER SETUP STEPS (for Main AP) & MESH SETUP STEPS
(for Satellite AP) for network setup.
When Single Router and Main AP in Mesh Router Set have the same operation steps, they are collectively referred to as Azores Router hereinafter .
03
ONE ROUTER SETUP STEPS
5
批注 [A2]: 图片设备体上和扫码提示文字 Master 与 Slave 需
要替换为 Main 和 Satellite
批注 [A3]: 需要替换 AX6600 两口图片
The Azores Router can be connected according to the diagram above. Note the DSL/PON/Cable Gateway must be connected to the WAN port of Azores Router. When it is connected to the Internet , the LED light is steady green. If you can, try place the Azores Router in an open area like on a table or a shelf.
Wired devices can be connected directly to LAN port for Internet access; wireless devices can use the network name (SSID) & password (see the sticker on the backside of Azores Router) to connect to Internet.
04
MESH SETUP STEPS
Place the Satellite AP at a proper location based on your home layout. After powering on again, Satellite AP is all set when the LED is steady green. To optimize wireless performance, place the Satellite AP in a location that minimizes the barrier (such as wall, door, and floor) between the Main AP and Satellite AP. We recommend one wall/door/floor between the Main AP and Satellite AP. You can connect the Satellite AP to your Main AP via network cable (preferred method) or wirelessly.
*Note:If you know there is a spot in your home, where the Wi-Fi signal is the weakest. Try place the Satellite AP midway between the Main AP and the weakest spot.
*Note:When Main AP and Satellite AP pairing successfully, the SSID and Password would be same, that is showing on the backside of Main AP.
批注
[A4]:
图片设备体上
Master
与
Slave
需要替换为
Main
和
Satellite
6
AX6600
05
Azores Router APP
01 Connect your Mobile device to Wi-Fi network according to the Wi-Fi SSID and password sticker on the backside of Azores Router.
02 Download mobile APP software by scanning the QR code below or visiting https://azoresnetworks.com/pages/app-download in the browser.
Scan QR code to download Azores Router APP
03 Follow the APP guidance to log in.
04 Enter the “My Wi-Fi” menu to modify WiFi configuration or perform other operations.
*Note: If you want to use the mobile device to perform other operations on the router, follow the instructions on the mobile APP.
7
06
Frequently Asked Questions
Q1 I replaced my old router with Azores
Router.After connecting network cable from
DSL/PON/Cable gateway to the Azores
Router, the LED is keep flashing red.What
should I do?
Answer:For some cable carriers limit the number of in-home device to one. This problem may happen if you replace your old router with Azores Router.In this case, you need to power down the cable gateway, leave it powered down for 15 seconds and power back it up. Afterwards, power down and on the Azores
Router.Then you should see the LED turns steady green pretty soon.
(3) Make sure the broadband service is normal and you have paid Internet bill.
(4) When all above are normal, try reboot the device and then check the network once it powers back on.
Q4 How to manage Azores Router network?
Answer: Connect your device to the Router using wireless or wired connection. Open an Internet browser and enter http://192.168.0.1(or http://azoresrouter.com). You can modify WAN configuration, router configuration, single SSID for 2.4
and 5G network, guest Wi-Fi network, and retrieve your wireless network status.
Q2 How to reset the device?
Answer: When Azores Router is powered on, pushing the “Reset” hole on the backside of the device with a needle. The LED starts to flash green and hold for 5 more seconds. Release when the LED turns off. The
LED will become steady red and will then start to blink green. Wait for about 2 minutes, then the factory default reset is completed.
Q3 Mobile phones and other devices are connected to the router but cannot access the Internet.
Answer: (1) Check whether the Azores Router's WAN port is connected to your Broadband Gateway. The
Azores Router's network port should be connected to your Broadband gateway (i.e. DSL/Cable modem,
PON gateway) with a network cable.
(2) If PPPoE Internet access is needed, you need to check whether the broadband account and password are filled in correctly; otherwise, check whether the
Internet status of your Broadband Gateway is normal.
Q5 Azores Router APP cannot control
Azores Router.What should I do?
Answer: Please check your phone is connected to
Wi-Fi normally, and use the correct login password to login in.
Q6 If the way that you connect to the network is different from shown in the figure in “ONE ROUTER SETUP STEPS”,or the IP address conflicts with the address of the deployed home router/gateway,how to configure Internet access?
Answer:Try put Router in bridge mode.Please scan the QR code(on page 1) to view the electronic user manual to switch to bridge mode.
Q7 What if I already purchased a Mesh
Router set and want to further expand the network with additional AP(s)?
Answer:You need to purchase another or more Azores routers(the same model) and expand the current mesh network.Please scan the QR code to view the electronic user manual to obtain the customized mesh
8
network operation method.
Q8 How to access the Satellite AP web management page(GUI) if the mesh pairing failed?
Answer:Manually set the PC IP address to
192.168.0.X(e.g.
192.168.0.100
),the subnet mask is
255.255.255.0.Open the browser and enter http://192.168.0.254.
9
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The manufacturer ensures that the frequency stability of this U-NII device can maintain transmission within the operating frequency band under all normal operating conditions.
