PowerFlex 40 Adjustable Frequency AC Drive ! ! ! ! !

PowerFlex 40 Adjustable Frequency AC Drive ! ! ! ! !
Quick Start
PowerFlex 40 Adjustable
Frequency AC Drive
FRN 1.xx - 4.xx
This Quick Start guide summarizes the basic steps needed to install,
start-up and program the PowerFlex 40 Adjustable Frequency AC Drive.
The information provided Does Not replace the User Manual and is
intended for qualified drive service personnel only.
For detailed PowerFlex 40 information including EMC instructions,
application considerations and related precautions refer to the
PowerFlex 40 User Manual, Publication 22B-UM001… on the CD
supplied with the drive or at www.rockwellautomation.com/literature.
General Precautions
!
ATTENTION: The drive contains high voltage capacitors which take
time to discharge after removal of mains supply. Before working on
drive, ensure isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage
levels. Failure to do so may result in personal injury or death.
Darkened display LEDs is not an indication that capacitors have
discharged to safe voltage levels.
!
!
!
!
ATTENTION: Equipment damage and/or personal injury may result
if parameter A092 [Auto Rstrt Tries] or A094 [Start At PowerUp] is
used in an inappropriate application. Do not use this function without
considering applicable local, national and international codes,
standards, regulations or industry guidelines.
ATTENTION: Only qualified personnel familiar with adjustable
frequency AC drives and associated machinery should plan or
implement the installation, start-up and subsequent maintenance of the
system. Failure to comply may result in personal injury and/or
equipment damage.
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic
Damage” or any other applicable ESD protection handbook.
ATTENTION: An incorrectly applied or installed drive can result in
component damage or a reduction in product life. Wiring or application
errors, such as, undersizing the motor, incorrect or inadequate AC
supply, or excessive ambient temperatures may result in malfunction of
the system.
English-2
Mounting Considerations
•
Mount the drive upright on a flat, vertical and level surface.
Frame
B
C
B (IP66,
Type 4X)
•
•
•
Screw Size
M4 (#8-32)
M5 (#10-24)
Screw Torque
1.56-1.96 N-m (14-17 lb.-in.)
2.45-2.94 N-m (22-26 lb.-in.)
DIN Rail
35 mm
–
M6 (#12-24)
3.95-4.75 N-m (35-42 lb.-in.)
–
Protect the cooling fan by avoiding dust or metallic particles.
Do not expose to a corrosive atmosphere.
Protect from moisture and direct sunlight.
Minimum Mounting Clearances
See Page 21 for mounting dimensions.
120 mm
(4.7 in.)
120 mm
(4.7 in.)
25 mm
(1.0 in.)
Closest object that
may restrict air flow
through the drive heat
sink and chassis
120 mm
(4.7 in.)
120 mm
(4.7 in.)
Mounting Option B
Mounting Option A
No clearance required
between drives.
Ambient Operating Temperatures
Ambient Temperature
Minimum
Maximum
Enclosure Rating
IP20, NEMA/UL Type Open
40°C (104°F) IP66, NEMA/UL Type 4X
-10°C (14°F)
IP30, NEMA/UL Type 1(1)
50°C (122°F) IP20, NEMA/UL Type Open
(1)
Minimum Mounting
Clearances
Use Mounting Option A
Use Mounting Option A
Use Mounting Option B
Use Mounting Option B
Rating requires installation of the PowerFlex 40 IP 30, NEMA/UL Type 1 option kit.
English-3
Typical Grounding
R/L1
S/L2
T/L3
U/T1
V/T2
W/T3
SHLD
Disconnecting MOVs
To prevent drive damage, the MOVs connected to ground shall be
disconnected if the drive is installed on an ungrounded distribution
system where the line-to-ground voltages on any phase could exceed
125% of the nominal line-to-line voltage. To disconnect these devices,
remove the jumper shown in the figures below.
1. Turn the screw counterclockwise to loosen.
2. Pull the jumper completely out of the drive chassis.
3. Tighten the screw to keep it in place.
Jumper Location
IP20, NEMA/UL Type Open
IP66, NEMA/UL Type 4X
Important: Tighten screw after jumper removal.
Phase to Ground MOV Removal
R/L1
Three-Phase
AC Input S/L2
T/L3
Jumper
1
2
3
4
English-4
CE Conformity
Refer to the PowerFlex 40 User Manual on the CD supplied with the
drive for details on how to comply with the Low Voltage (LV) and
Electromagnetic Compatibility (EMC) Directives.
Specifications, Fuses and Circuit Breakers
Drive Ratings
Catalog
Number(1)
Power
Dissipation
IP20 Open
Contactors Watts
Output Ratings
Input Ratings
Branch Circuit Protection
kW (HP)
Voltage
Range
Fuses
Amps
kVA Amps
140M Motor
Protectors
100 - 120V AC (±10%) – 1-Phase Input, 0 - 230V 3-Phase Output
22B-V2P3x104
0.4 (0.5)
2.3
90-132
1.15 9.0
15
140M-C2E-C16 100-C12
40
22B-V5P0x104
0.75 (1.0)
5.0
90-132
2.45 20.3
35
140M-D8E-C20 100-C23
60
22B-V6P0x104
1.1 (1.5)
6.0
90-132
3.0
40
140M-F8E-C32 100-C37
80
24.0
200 - 240V AC (±10%) – 1-Phase(2) Input, 0 - 230V 3-Phase Output
22B-A2P3x104
0.4 (0.5)
2.3
180-264
1.15 6.0
10
140M-C2E-B63 100-C09
40
22B-A5P0x104
0.75 (1.0)
5.0
180-264
2.45 12.0
20
140M-C2E-C16 100-C12
60
22B-A8P0x104
1.5 (2.0)
8.0
180-264
4.0
18.0
30
140M-D8E-C20 100-C23
85
22B-A012x104
2.2 (3.0)
12.0
180-264
5.5
25.0
40
140M-F8E-C32 100-C37
125
200 - 240V AC (±10%) – 3-Phase Input, 0 - 230V 3-Phase Output
22B-B2P3x104
0.4 (0.5)
2.3
180-264
1.15 2.5
6
140M-C2E-B40 100-C07
40
22B-B5P0x104
0.75 (1.0)
5.0
180-264
2.45 5.7
10
140M-C2E-C10 100-C09
60
22B-B8P0x104
1.5 (2.0)
8.0
180-264
4.0
9.5
15
140M-C2E-C16 100-C12
85
22B-B012x104
2.2 (3.0)
12.0
180-264
5.5
15.5
25
140M-C2E-C16 100-C23
125
22B-B017x104
3.7 (5.0)
17.5
180-264
8.6
21.0
30
140M-F8E-C25 100-C23
180
22B-B024x104
5.5 (7.5)
24.0
180-264
11.8 26.1
40
140M-F8E-C32 100-C37
235
22B-B033x104
7.5 (10.0)
33.0
180-264
16.3 34.6
60
140M-G8E-C45 100-C60
305
380 - 480V AC (±10%) – 3-Phase Input, 0 - 460V 3-Phase Output
22B-D1P4x104
0.4 (0.5)
1.4
342-528
1.4
1.8
3
140M-C2E-B25 100-C07
35
22B-D2P3x104
0.75 (1.0)
2.3
342-528
2.3
3.2
6
140M-C2E-B40 100-C07
50
22B-D4P0x104
1.5 (2.0)
4.0
342-528
4.0
5.7
10
140M-C2E-B63 100-C09
70
22B-D6P0x104
2.2 (3.0)
6.0
342-528
5.9
7.5
15
140M-C2E-C10 100-C09
100
22B-D010x104
4.0 (5.0)
10.5
342-528
10.3 13.0
20
140M-C2E-C16 100-C23
160
22B-D012x104
5.5 (7.5)
12.0
342-528
11.8 14.2
25
140M-D8E-C20 100-C23
175
22B-D017x104
7.5 (10.0)
17.0
342-528
16.8 18.4
30
140M-D8E-C20 100-C23
210
22B-D024x104
11.0 (15.0) 24.0
342-528
23.4 26.0
50
140M-F8E-C32 100-C43
300
460 - 600V AC (±10%) – 3-Phase Input, 0 - 575V 3-Phase Output
22B-E1P7x104
0.75 (1.0)
1.7
414-660
2.1
2.3
6
140M-C2E-B25 100-C09
50
22B-E3P0x104
1.5 (2.0)
3.0
414-660
3.65 3.8
6
140M-C2E-B40 100-C09
70
22B-E4P2x104
2.2 (3.0)
4.2
414-660
5.2
5.3
10
140M-C2E-B63 100-C09
100
22B-E6P6x104
4.0 (5.0)
6.6
414-660
8.1
8.3
15
140M-C2E-C10 100-C09
160
22B-E9P9x104
5.5 (7.5)
9.9
414-660
12.1 11.2
20
140M-C2E-C16 100-C16
175
22B-E012x104
7.5 (10.0)
12.2
414-660
14.9 13.7
25
140M-C2E-C16 100-C23
210
22B-E019x104
11.0 (15.0) 19.0
414-660
23.1 24.1
40
140M-D8E-C25 100-C30
300
(1)
(2)
In the Catalog Numbers listed “x” represents enclosure type. Specifications are valid for all
enclosure types. IP66, NEMA/UL Type 4X drive ratings are only available as Frame B drives.
200-240V AC - 1-Phase drives are also available with an integral EMC filter. Catalog suffix
changes from N104 to N114. Filter option is not available for IP66, NEMA/UL Type 4X rated drives.
English-5
Approvals
Input/Output Ratings
LIS
TED 966X
UL
Output Frequency: 0-400 Hz (Programmable)
Efficiency: 97.5% (Typical)
®
IN
LIS
UL508C
C
®
IN
D CO N T EQ
TED 966X
UL
CSA 22.2
D CO N T EQ
EMC Directive 89/336
LV:
EN 50178, EN 60204
EMC: EN 61800-3, EN 50081-1, EN 50082-2
Digital Control Inputs (Input Current = 6mA)
Analog Control Inputs
SRC (Source) Mode:
18-24V = ON
0-6V = OFF
4-20mA Analog: 250 ohm input impedance
0-10V DC Analog: 100k ohm input impedance
External Pot: 1-10k ohms, 2 Watt minimum
SNK (Sink) Mode:
0-6V = ON
18-24V = OFF
Control Output
Programmable Output (form C relay)
Resistive Rating: 3.0A at 30V DC, 3.0A at 125V AC, 3.0A at 240V AC
Inductive Rating: 0.5A at 30V DC, 0.5A at 125V AC, 0.5A at 240V AC
Opto Outputs
30V DC, 50mA
Non-inductive
Analog Outputs (10 bit)
0-10V, 1k ohm Min.
4-20mA, 525 ohm Max.
Fuses and Circuit Breakers
Recommended Fuse Type: UL Class J, CC, T or Type BS88; 600V (550V) or equivalent.
Recommended Circuit Breakers: HMCP circuit breakers or equivalent.
Protective Features
Motor Protection: I2t overload protection - 150% for 60 Secs, 200% for 3 Secs (Provides Class 10 protection)
Overcurrent: 200% hardware limit, 300% instantaneous fault
Over Voltage:
100-120V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 150V AC incoming line)
200-240V AC Input – Trip occurs at 405V DC bus voltage (equivalent to 290V AC incoming line)
380-460V AC Input – Trip occurs at 810V DC bus voltage (equivalent to 575V AC incoming line)
460-600V AC Input – Trip occurs at 1005V DC bus voltage (equivalent to 711V AC incoming line)
Under Voltage: 100-120V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 75V AC incoming line)
200-240V AC Input – Trip occurs at 210V DC bus voltage (equivalent to 150V AC incoming line)
380-480V AC Input – Trip occurs at 390V DC bus voltage (equivalent to 275V AC incoming line)
460-600V AC Input – If P042 = 3 “High Voltage” trip occurs at 487V DC bus voltage (344V AC incoming line);
If P042 = 2 “Low Voltage” trip occurs at 390V DC bus voltage (275V AC incoming line)
Control Ride Through: Minimum ride through is 0.5 Secs - typical value 2 Secs
Faultless Power Ride Through: 100 milliseconds
Dynamic Braking
Internal brake IGBT included with all ratings except No Brake versions. Refer to Appendix B of the PowerFlex 40 User Manual
on CD for DB resistor ordering information.
English-6
Power Wiring
Power Wire Rating
Recommended Copper
Wire
Unshielded 600V, 75°C (167°F) THHN/THWN
15 Mils insulated, dry location
Shielded 600V, 75°C or 90°C (167°F or 194°F) RHH/
RHW-2
Anixter OLF-7xxxxx,
Belden 29501-29507 or
equivalent
Anixter 7V-7xxxx-3G
Shielded Tray rated 600V, 75°C or 90°C (167°F or 194°F) Shawflex 2ACD/3ACD or
RHH/RHW-2
equivalent
Power Terminal Block
B Frame
C Frame
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
R/L1 S/L2 T/L3 U/T1 V/T2 W/T3
DC- DC+ BR+ BR-
Terminal (1)
Description
R/L1, S/L2
1-Phase Input
P2
P1
DC- DC+ BR+ BR-
R/L1, S/L2, T/L3 3-Phase Input
U/T1
To Motor U/T1
V/T2
To Motor V/T2
W/T3
=
To Motor W/T3
Switch any two motor
leads to change
forward direction.
DC Bus Inductor Connection (C Frame drives only.)
P2, P1
The C Frame drive is shipped with a jumper between
Terminals P2 and P1. Remove this jumper only when a DC
Bus Inductor will be connected. Drive will not power up
without a jumper or inductor connected.
DC+, DC-
DC Bus Connection
BR+, BR-
Dynamic Brake Resistor Connection
Safety Ground - PE
(1)
Important: Terminal screws may become loose during shipment. Ensure that all
terminal screws are tightened to the recommended torque before applying power to
the drive.
Power Terminal Block Specifications
Frame
Maximum Wire Size (2) Minimum Wire Size (2) Torque
B
5.3 mm2 (10 AWG)
1.3 mm2 (16 AWG)
1.7-2.2 N-m (16-19 lb.-in.)
C
8.4 mm2
1.3 mm2 (16 AWG)
2.9-3.7 N-m (26-33 lb.-in.)
(2)
(8 AWG)
Maximum/minimum sizes that the terminal block will accept - these are not
recommendations.
English-7
Input Power Conditions
Input Power Condition
Corrective Action
Low Line Impedance (less than 1% line reactance) • Install Line Reactor(2)
• or Isolation Transformer
Greater than 120 kVA supply transformer
• or Bus Inductor – 5.5-11 kW
(7.5-15 HP) drives only
Line has power factor correction capacitors
Line has frequent power interruptions
• Install Line Reactor
• or Isolation Transformer
Line has intermittent noise spikes in excess of
6000V (lightning)
Phase to ground voltage exceeds 125% of normal
line to line voltage
Ungrounded distribution system
240V open delta configuration (stinger leg)(1)
(1)
(2)
• Remove MOV jumper to ground.
• or Install Isolation Transformer
with grounded secondary if
necessary.
• Install Line Reactor
For drives applied on an open delta with a middle phase grounded neutral system, the
phase opposite the phase that is tapped in the middle to the neutral or earth is
referred to as the “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified
throughout the system with red or orange tape on the wire at each connection point.
The stinger leg should be connected to the center Phase B on the reactor. Refer to the
PowerFlex 40 User Manual on CD for specific line reactor part numbers.
Refer to Appendix B of the PowerFlex 40 User Manual on CD for accessory ordering
information.
I/O Wiring Recommendations (3)
Wire Type(s)(4)
Description
Belden 8760/9460
(or equiv.)
0.8 mm2 (18AWG), twisted pair, 100% shield
300V
with drain.
60 degrees C
0.8 mm2 (18AWG), 3 conductor, shielded for (140 degrees F)
remote pot only.
Belden 8770
(or equiv.)
(3)
(4)
Minimum Insulation
Rating
If the wires are short and contained within a cabinet which has no sensitive circuits,
the use of shielded wire may not be necessary, but is always recommended.
Stranded or solid wire.
I/O Terminal Block Specifications
Frame
Maximum Wire Size (5) Minimum Wire Size (5) Torque
B&C
1.3 mm2 (16 AWG)
(5)
0.2 mm2 (24 AWG)
0.5-0.8 N-m (4.4-7 lb.-in.)
Maximum / minimum that the terminal block will accept - these are not
recommendations.
Refer to the PowerFlex 40 User Manual on CD for maximum power and
control cable length recommendations.
English-8
Control Terminal Block
Control Wiring Block Diagram
Enable
Jumper
(4)
01
02
03
SNK
SRC
04
05
06
07
08
09
+24V
11
+10V
12
13
14
Relay N.O.
Relay Common
Relay N.C.
R1
0-10V
R2
0/4-20mA
15
16
17
R3
30V DC
50mA
Non-inductive
0-10V
0-20mA
R1 R2 R3
Analog Output Select
18
19
Stop
Typical
SRC Wiring
(1)(4)
Start/Run FWD
Typical
SNK Wiring
(2)
Direction/Run REV
Digital Common
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Opto Common
+24V DC
+10V DC
0-10V (or ±10V) Input
Analog Common
Pot must be
1-10k ohm
2 Watt Min.
4-20mA Input
Analog Output
Common
Opto Output 1
(3)
24V
Opto Output 2
RS485 Shield
ENBL
01 02 03 04 05 06 07 08 09
SNK
11 12 13 14 15 16 17 18 19
Enable
Jumper
(4)
RS485
(DSI)
SRC
(1)
30V DC 125V AC 240V AC
Resistive
3.0A
3.0A
3.0A
Inductive
0.5A
0.5A
0.5A
1
(1)Important: I/O Terminal 01 is always a coast to
stop input except when P036 [Start Source] is set to
3-Wire
Per P037
Per P037
“3-Wire” or “Momt FWD/REV” control. In three wire
2-Wire
Per P037
Coast
control, I/O Terminal 01 is controlled by P037 [Stop
RS485 Port
Per P037
Coast
Mode]. All other stop sources are controlled by P037
[Stop Mode].
Important: The drive is shipped with a jumper installed between I/O Terminals 01 and 11. Remove
this jumper when using I/O Terminal 01 as a stop or enable input.
P036 [Start Source]
Stop
I/O Terminal 01 Stop
Keypad
Per P037
Coast
(2)
Two wire control shown. For three wire control use a momentary input
on I/O Terminal 02 to
command a start. Use a maintained input
for I/O Terminal 03 to change direction.
(3)
When using an opto output with an inductive load such as a relay, install a recovery diode parallel
to the relay as shown, to prevent damage to the output.
(4)
When the ENBL jumper is removed, I/O Terminal 01 will always act as a hardware enable, causing
a coast to stop without software interpretation. Refer to the PowerFlex 40 User Manual on CD for
more information.
English-9
Control I/O Terminal Designations
No. Signal
Default
Description
Param.
R1
Relay N.O.
Fault
Normally open contact for output relay.
A055
R2
Relay Common
–
Common for output relay.
R3
Relay N.C.
Fault
Normally closed contact for output relay.
Analog Output Select
DIP Switch
0-10V
Sets analog output to either voltage or current. Setting must match
A065 [Analog Out Sel].
Sink/Source
DIP Switch
Source (SRC)
Inputs can be wired as Sink (SNK) or Source (SRC) via DIP Switch
setting.
A055
P036 (1)
01
Stop (1)
Coast
The factory installed jumper or a normally closed
input must be present for the drive to start.
02
Start/Run FWD
Not Active
03
Direction/Run REV Not Active
Command comes from the integral keypad by default. P036, P037
To disable reverse operation, see A095 [Reverse
P036, P037,
Disable].
A095
04
Digital Common
–
For digital inputs. Electronically isolated with digital
inputs from analog I/O and opto outputs.
05
Digital Input 1
Preset Freq
Program with A051 [Digital In1 Sel].
A051
06
Digital Input 2
Preset Freq
Program with A052 [Digital In2 Sel].
A052
07
Digital Input 3
Local
Program with A053 [Digital In3 Sel].
A053
08
Digital Input 4
Jog Forward
Program with A054 [Digital In4 Sel].
A054
09
Opto Common
–
For opto-coupled outputs. Electronically isolated with
opto outputs from analog I/O and digital inputs.
11
+24V DC
–
Referenced to Digital Common.
Drive supplied power for digital inputs.
Maximum output current is 100mA.
12
+10V DC
–
Referenced to Analog Common.
Drive supplied power for 0-10V external
potentiometer.
Maximum output current is 15mA.
13
±10V In (2)
Not Active
For external 0-10V (unipolar) or ±10V (bipolar) input P038,
supply (input impedance = 100k ohm) or
A051-A054,
potentiometer wiper.
A123, A132
14
Analog Common
–
For 0-10V In or 4-20mA In. Electronically isolated
with analog inputs and outputs from digital I/O and
opto outputs.
15
4-20mA In (2)
Not Active
For external 4-20mA input supply
(input impedance = 250 ohm).
16
Analog Output
OutFreq 0-10
The default analog output is 0-10V. To covert to a
A065, A066
current value, change the Analog Output Select DIP
Switch to 0-20mA. Program with A065 [Analog Out
Sel]. Max analog value can be scaled with A066
[Analog Out High].
Maximum Load: 4-20mA = 525 ohm (10.5V)
0-10V = 1k ohm (10mA)
17
Opto Output 1
MotorRunning
Program with A058 [Opto Out1 Sel]
A058, A059,
A064
18
Opto Output 2
At Frequency
Program with A061 [Opto Out2 Sel]
A061, A062,
A064
19
RS485 (DSI) Shield –
(1)
(2)
P038
P038,
A051-A054,
A132
Terminal should be connected to safety ground - PE
when using the RS485 (DSI) communications port.
See Footnotes (1) and (4) on page 8.
0-10V In and 4-20mA In are distinct input channels and may be connected simultaneously.
Inputs may be used independently for speed control or jointly when operating in PID mode.
English-10
Prepare For Drive Start-Up
!
ATTENTION: Power must be applied to the drive to perform the
following start-up procedures. Some of the voltages present are at
incoming line potential. To avoid electric shock hazard or damage to
equipment, only qualified service personnel should perform the
following procedure. Thoroughly read and understand the procedure
before beginning. If an event does not occur while performing this
procedure, Do Not Proceed. Remove All Power including user
supplied control voltages. User supplied voltages may exist even when
main AC power is not applied to the drive. Correct the malfunction
before continuing.
Before Applying Power to the Drive
❏ 1. Confirm that all inputs are connected to the correct terminals and are
secure.
❏ 2. Verify that AC line power at the disconnect device is within the rated
value of the drive.
❏ 3. Verify that any digital control power is 24 volts.
❏ 4. Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to
match your control wiring scheme. See page 8 for location.
Important: The default control scheme is Source (SRC). The Stop
terminal is jumpered (I/O Terminals 01 and 11) to allow
starting from the keypad. If the control scheme is changed
to Sink (SNK), the jumper must be removed from I/O
Terminals 01 and 11 and installed between I/O Terminals
01 and 04.
❏ 5. Verify that the Stop input is present or the drive will not start.
Important: If I/O Terminal 01 is used as a stop input, the jumper
between I/O Terminals 01 and 11 must be removed.
Applying Power to the Drive
❏ 6. Apply AC power and control voltages to the drive.
❏ 7. Familiarize yourself with the integral keypad features (see next page)
before setting any Program Group parameters.
English-11
Start, Stop, Direction and Speed Control
Factory default parameter values allow the drive to be controlled from
the integral keypad. No programming is required to start, stop, change
direction and control speed directly from the integral keypad.
To change the speed reference of an IP66, NEMA/UL Type 4X rated
drive, access parameter A069 [Internal Freq] and press Enter or Sel to
enter program mode. Use the Up Arrow or Down Arrow key to adjust the
speed reference. Press the Enter key to save the new value.
Important: To disable reverse operation, see A095 [Reverse Disable].
If a fault appears on power up, refer to page 20 for an explanation of the
fault code. For complete troubleshooting information, refer to the
PowerFlex 40 User Manual on the CD supplied with the drive.
English-12
Integral Keypad
➋
➊
➌
RUN
FWD
REV
PROGRAM
➍
➏
Menu
VOLTS
AMPS
HERTZ
➎
FAULT
➑
➐
Description
Display Group (View Only)
Consists of commonly viewed drive operating
conditions.
➒
Basic Program Group
Consists of most commonly used
programmable functions.
Advanced Program Group
Consists of remaining programmable functions.
Fault Designator
Consists of list of codes for specific fault
conditions. Displayed only when fault is present.
No. LED
➊ Run/Direction
Status
LED State
Steady Red
Flashing Red
➋
Alphanumeric
Display
Steady Red
Flashing Red
➌
➍
➎
➏
➐
Displayed Units
Steady Red
Description
Indicates drive is running and commanded motor direction.
Drive has been commanded to change direction. Indicates
actual motor direction while decelerating to zero.
Indicates parameter number, parameter value, or fault code.
Single digit flashing indicates that digit can be edited.
All digits flashing indicates a fault condition.
Indicates the units of the parameter value being displayed.
Program Status
Steady Red
Indicates parameter value can be changed.
Fault Status
Flashing Red
Indicates drive is faulted.
Pot Status
Steady Green
Indicates potentiometer on Integral Keypad is active.(1)
Start Key Status Steady Green
No. Key
➑
➒
Name
Escape
Description
Back one step in programming menu.
Cancel a change to a parameter value and exit Program
Mode.
Select
Advance one step in programming menu.
Select a digit when viewing parameter value.
Scroll through groups and parameters.
Up Arrow
Down Arrow
Increase/decrease the value of a flashing digit.
Used to control speed of IP66, NEMA/UL Type 4X rated
drives when P038 [Speed Reference] is selected.
Enter
Advance one step in programming menu.
Save a change to a parameter value.
Potentiometer(1) Used to control speed of drive. Default is active.
Controlled by parameter P038 [Speed Reference].
Start
Reverse
Stop
(1)
Indicates Start key on Integral Keypad is active.
The Reverse key is also active unless disabled by A095
[Reverse Disable].
Used to start the drive. Default is active.
Controlled by parameter P036 [Start Source].
Used to reverse direction of the drive. Default is active.
Controlled by parameters P036 [Start Source] and A095
[Reverse Disable].
Used to stop the drive or clear a fault.
This key is always active.
Controlled by parameter P037 [Stop Mode].
IP66, NEMA/UL Type 4X rated drives are not equipped with a potentiometer.
English-13
See the PowerFlex 40 User Manual on CD for more information on parameters.
Viewing and Editing Parameters
The last user-selected Display Group parameter is saved when power is removed and is displayed by
default when power is reapplied.
The following is an example of basic integral keypad and display functions. This example provides basic
navigation instructions and illustrates how to program the first Program Group parameter.
Step
Key(s)
1. When power is applied, the last user-selected
Display Group parameter number is briefly
displayed with flashing characters. The display
then defaults to that parameter’s current value.
(Example shows the value of d001 [Output
Freq] with the drive stopped.)
Example Displays
VOLTS
AMPS
HERTZ
PROGRAM
2. Press Esc once to display the Display Group
parameter number shown on power-up. The
parameter number will flash.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
3. Press Esc again to enter the group menu. The
group menu letter will flash.
VOLTS
AMPS
HERTZ
4. Press the Up Arrow or Down Arrow to scroll
through the group menu (d, P and A).
or
5. Press Enter or Sel to enter a group. The right
digit of the last viewed parameter in that group
will flash.
or
6. Press the Up Arrow or Down Arrow to scroll
through the parameters that are in the group.
or
7. Press Enter or Sel to view the value of a
parameter. If you do not want to edit the value,
press Esc to return to the parameter number.
or
8. Press Enter or Sel to enter program mode to
edit the parameter value. The right digit will
flash and the Program LED will illuminate if the
parameter can be edited.
or
9. Press the Up Arrow or Down Arrow to change
the parameter value. If desired, press Sel to
move from digit to digit or bit to bit. The digit or
bit that you can change will flash.
or
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
FAULT
10. Press Esc to cancel a change. The digit will
stop flashing, the previous value is restored and
the Program LED will turn off.
Or
Press Enter to save a change. The digit will stop
flashing and the Program LED will turn off.
VOLTS
AMPS
HERTZ
PROGRAM
11. Press Esc to return to the parameter list.
Continue to press Esc to back out of the
programming menu.
FAULT
VOLTS
AMPS
HERTZ
PROGRAM
If pressing Esc does not change the display,
then d001 [Output Frequency] is displayed.
Press Enter or Sel to enter the group menu.
The Basic Program Group contains the most commonly changed parameters
.
FAULT
English-14
See the PowerFlex 40 User Manual on CD for more information on parameters.
Display Group Parameters
No.
Parameter
Min/Max
Display/Options
d001 [Output Freq]
0.0/[Maximum Freq]
0.1 Hz
d002 [Commanded Freq]
0.0/[Maximum Freq]
0.1 Hz
d003 [Output Current]
0.00/(Drive Amps × 2)
0.01 Amps
d004 [Output Voltage]
0/Drive Rated Volts
1 VAC
d005 [DC Bus Voltage]
Based on Drive Rating
1 VDC
d006 [Drive Status]
0/1 (1 = Condition True)
Bit 3
Decelerating
d007- [Fault x Code]
d009
F2/F122
F1
d010 [Process Display]
0.00/9999
0.01 – 1
d012 [Control Source]
0/9
Digit 1 = Speed Command
(See P038; 9 = “Jog Freq”)
Digit 0 = Start Command
(See P036; 9 = “Jog”)
d013 [Contrl In Status]
0/1 (1 = Input Present)
Bit 3
DB Trans On
Bit 2
Stop Input
Bit 1
Dir/REV In
Bit 0
Start/FWD In
d014 [Dig In Status]
0/1 (1 = Input Present)
Bit 3
Digital In 4
Bit 2
Digital In 3
Bit 1
Digital In 2
Bit 0
Digital In 1
d015 [Comm Status]
0/1 (1 = Condition True)
Bit 3
Comm Error
Bit 2
DSI Option
Bit 1
Transmitting
Bit 0
Receiving
d016 [Control SW Ver]
1.00/99.99
0.01
d017 [Drive Type]
1001/9999
1
d018 [Elapsed Run Time]
0/9999 Hrs
1 = 10 Hrs
d019 [Testpoint Data]
0/FFFF
1 Hex
d020 [Analog In 0-10V]
0.0/100.0%
0.1%
d021 [Analog In 4-20mA]
0.0/100.0%
0.1%
d022 [Output Power]
0.00/(Drive Power × 2)
0.01 kW
d023 [Output Powr Fctr]
0.0/180.0 deg
0.1 deg
d024 [Drive Temp]
0/120 degC
1 degC
d025 [Counter Status]
0/9999
1
d026 [Timer Status]
0.0/9999 Secs
0.1 Secs
d028 [Stp Logic Status]
0/7
1
d029 [Torque Current]
0.00/(Drive Amps × 2)
0.01 Amps
Bit 2
Accelerating
Bit 1
Forward
Bit 0
Running
English-15
See the PowerFlex 40 User Manual on CD for more information on parameters.
Smart Start-Up with Basic Program Group Parameters
The PowerFlex 40 is designed so that start up is simple and efficient. The Program Group
contains the most commonly used parameters.
= Stop drive before changing this parameter.
No.
Parameter
P031 [Motor NP Volts]
Min/Max
Display/Options
Default
20/Drive Rated Volts
1 VAC
Based on Drive Rating
1 Hz
60 Hz
Set to the motor nameplate rated volts.
P032 [Motor NP Hertz]
15/400 Hz
Set to the motor nameplate rated frequency.
P033 [Motor OL Current] 0.0/(Drive Rated Amps×2) 0.1 Amps
Set to the maximum allowable motor current.
Based on Drive Rating
P034 [Minimum Freq]
0.1 Hz
0.0 Hz
P035 [Maximum Freq]
0/400 Hz
Sets the highest frequency the drive will output.
1 Hz
60 Hz
P036 [Start Source]
0 = “Keypad”(1)
1 = “3-Wire”
2 = “2-Wire”
3 = “2-W Lvl Sens”
4 = “2-W Hi Speed”
5 = “Comm Port”
6 = “Momt FWD/REV”
0
0 = “Ramp, CF”(1)
1 = “Coast, CF”(1)
2 = “DC Brake, CF”(1)
3 = “DCBrkAuto,CF”(1)
4 = “Ramp”
5 = “Coast”
6 = “DC Brake”
7 = “DC BrakeAuto”
8 = “Ramp+EM B,CF”
9 = “Ramp+EM Brk”
(1) Stop input also clears active fault.
0
0.0/400.0 Hz
Sets the lowest frequency the drive will output
continuously.
0/6
Sets the control scheme used to start the drive.
(1)
When active, the Reverse key is also active
unless disabled by A095 [Reverse Disable].
P037 [Stop Mode]
0/9
Active stop mode for all stop sources [e.g. keypad,
run forward (I/O Terminal 02), run reverse (I/O
Terminal 03), RS485 port] except as noted below.
Important: I/O Terminal 01 is always a coast to
stop input except when P036 [Start Source] is set
for “3-Wire” control. When in three wire control, I/O
Terminal 01 is controlled by P037 [Stop Mode].
P038 [Speed Reference]
0/7
Sets the source of the speed reference to the
drive.
Important: When A051 or A052 [Digital Inx Sel] is
set to option 2, 4, 5, 6, 13 or 14 and the digital
input is active, A051, A052, A053 or A054 will
override the speed reference commanded by this
parameter. Refer to Chapter 1 of the PowerFlex 40
User Manual on CD for details.
P039 [Accel Time 1]
0.0/600.0 Secs
0 = “Drive Pot”
1 = “InternalFreq”
2 = “0-10V Input”
3 = “4-20mA Input”
4 = “Preset Freq”
5 = “Comm Port”
6 = “Stp Logic”
7 = “Anlg In Mult”
0
1 (IP66, Type 4X)
0.1 Secs
10.0 Secs
Sets the rate of accel for all speed increases.
P040 [Decel Time 1]
0.1/600.0 Secs
0.1 Secs
10.0 Secs
0 = “Ready/Idle”
1 = “Factory Rset”
0
2 = “Low Voltage” (480V)
3 = “High Voltage” (600V)
3
Sets the rate of decel for all speed decreases.
P041 [Reset To Defalts]
0/1
Resets all parameter values to factory defaults.
P042 [Voltage Class]
2/3
Sets the voltage class of 600V drives.
P043 [Motor OL Ret]
0/1
0 = “Disabled”
1 = “Enabled”
Enables/disables the Motor Overload Retention function.
0
English-16
See the PowerFlex 40 User Manual on CD for more information on parameters.
Advanced Group Parameters
No.
Parameter
Min/Max
Display/Options
0/27
A051 [Digital In1 Sel]
I/O Terminal 05
A052 [Digital In2 Sel]
I/O Terminal 06
A053 [Digital In3 Sel]
I/O Terminal 07
A054 [Digital In4 Sel]
I/O Terminal 08
(1)
Important: Speed source for IP66, NEMA/
UL Type 4X rated drives comes from A069
[Internal Freq].
A055 [Relay Out Sel]
0/23
A056
A058
A061
A059
A062
0.0/9999
0/22
0 = “Not Used”
1 = “Acc & Dec 2”
2 = “Jog”
3 = “Aux Fault”
4 = “Preset Freq”
5 = “Local”(1)
6 = “Comm Port”
7 = “Clear Fault”
8 = “RampStop,CF”
9 = “CoastStop,CF”
10 = “DCInjStop,CF”
11 = “Jog Forward”
12 = “Jog Reverse”
13 = “10V In Ctrl”
0 = “Ready/Fault”
1 = “At Frequency”
2 = “MotorRunning”
3 = “Reverse”
4 = “Motor Overld”
5 = “Ramp Reg”
6 = “Above Freq”
7 = “Above Cur”
8 = “Above DCVolt”
9 = “Retries Exst”
10 = “Above Anlg V”
11 = “Logic In 1”
0.1
See A055 for Options.
0.0/9999
0.1
[Relay Out Level]
[Opto Out1 Sel]
[Opto Out2 Sel]
[Opto Out1 Level]
[Opto Out2 Level]
A055, A058 & A061 Setting
6
7
8
10
16
17
18
20
23
A064 [Opto Out Logic]
A064 Option
0
1
2
3
Default
14 = “20mA In Ctrl”
15 = “PID Disable”
16 = “MOP Up”
17 = “MOP Down”
18 = “Timer Start”
19 = “Counter In”
20 = “Reset Timer”
21 = “Reset Countr”
22 = “Rset Tim&Cnt”
23 = “Logic In1”
24 = “Logic In2”
25 = “Current Lmt2”
26 = “Anlg Invert”
27 = “EM Brk Rlse”
12 = “Logic In 2”
13 = “Logic 1 & 2”
14 = “Logic 1 or 2”
15 = “StpLogic Out”
16 = “Timer Out”
17 = “Counter Out”
18 = “Above PF Ang”
19 = “Anlg In Loss”
20 = “ParamControl”
21 = “NonRec Fault”
22 = “EM Brk Cntrl”
23 = “Above Fcmd”
4
4
5
11
0
0.0
2
1
0.0
A056, A059 & A062 Min/Max
0/400 Hz
0/180%
0/815 Volts
0/100%
0.1/9999 Secs
1/9999 Counts
1/180 degs
0/1
0/400 Hz
0/3
Opto Out1 Logic
NO (Normally Open)
NC (Normally Closed)
NO (Normally Open)
NC (Normally Closed)
1
Opto Out2 Logic
NO (Normally Open)
NO (Normally Open)
NC (Normally Closed)
NC (Normally Closed)
0
English-17
See the PowerFlex 40 User Manual on CD for more information on parameters.
No.
Parameter
A065 [Analog Out Sel]
Option
0 “OutFreq 0-10”
1 “OutCurr 0-10”
2 “OutVolt 0-10”
3 “OutPowr 0-10”
4 “TstData 0-10”
5 “OutFreq 0-20”
6 “OutCurr 0-20”
7 “OutVolt 0-20”
8 “OutPowr 0-20”
9 “TstData 0-20”
10 “OutFreq 4-20”
11 “OutCurr 4-20”
12 “OutVolt 4-20”
13 “OutPowr 4-20”
14 “TstData 4-20”
15 “OutTorq 0-10”
16 “OutTorq 0-20”
17 “OutTorq 4-20”
18 “Setpnt 0-10”
19 “Setpnt 0-20”
20 “Setpnt 4-20”
21 “MinFreq 0-10”
22 “MinFreq 0-20”
23 “MinFreq 4-20”
A066
A067
A068
A069
A070
A071
A072
A073
A074
A075
A076
A077
Min/Max
Display/Options
Default
0/23
1
0
Output Range
0-10V
0-10V
0-10V
0-10V
0-10V
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
4-20 mA
4-20 mA
4-20 mA
4-20 mA
4-20 mA
0-10V
0-20 mA
4-20 mA
0-10V
0-20 mA
4-20 mA
0-10V
0-20 mA
4-20 mA
Minimum Output Value
0V = 0 Hz
0V = 0 Amps
0V = 0 Volts
0V = 0 kW
0V = 0000
0 mA = 0 Hz
0 mA = 0 Amps
0 mA = 0 Volts
0 mA = 0 kW
0 mA = 0000
4 mA = 0 Hz
4 mA = 0 Amps
4 mA = 0 Volts
4 mA = 0 kW
4 mA = 0000
0V = 0 Amps
0 mA = 0 Amps
4 mA = 0 Amps
0V = 0%
0 mA = 0%
4 mA = 0%
0V = Min. Freq
0 mA = Min. Freq
4 mA = Min. Freq
Maximum Output Value
[Analog Out High]
P035 [Maximum Freq]
200% Drive Rated FLA
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 [Maximum Freq]
200% Drive Rated FLA
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
P035 [Maximum Freq]
200% Drive Rated FLA
120% Drive Rated Output Volts
200% Drive Rated Power
65535 (Hex FFFF)
200% Drive Rated FLA
200% Drive Rated FLA
200% Drive Rated FLA
100.0% Setpoint Setting
100.0% Setpoint Setting
100.0% Setpoint Setting
P035 [Maximum Freq]
P035 [Maximum Freq]
P035 [Maximum Freq]
DIP Switch Position
0-10V
0-10V
0-10V
0-10V
0-10V
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-20 mA
0-10V
0-20 mA
0-20 mA
0-10V
0-20 mA
0-20 mA
0-10V
0-20 mA
0-20 mA
[Analog Out High]
0/800%
1%
[Accel Time 2]
0.0/600.0 Secs
0.1 Secs
[Decel Time 2]
0.1/600.0 Secs
0.1 Secs
[Internal Freq]
0.0/400.0 Hz
0.1 Hz
[Preset Freq 0](1)
0.0/400.0 Hz
0.1 Hz
[Preset Freq 1]
[Preset Freq 2]
[Preset Freq 3]
[Preset Freq 4]
[Preset Freq 5]
[Preset Freq 6]
[Preset Freq 7]
(1) To activate [Preset Freq 0] set P038 [Speed Reference] to option 4.
100%
20.0 Secs
20.0 Secs
60.0 Hz
0.0 Hz
5.0 Hz
10.0 Hz
20.0 Hz
30.0 Hz
40.0 Hz
50.0 Hz
60.0 Hz
Input State
Input State
Input State
(2)
of Digital In 1
of Digital In 2
of Digital In 3
Frequency Source
Accel / Decel Parameter Used
(I/O Terminal 05) (I/O Terminal 06) (I/O Terminal 07)
0
0
0
[Preset Freq 0]
[Accel Time 1] / [Decel Time 1]
1
0
0
[Preset Freq 1]
[Accel Time 1] / [Decel Time 1]
0
1
0
[Preset Freq 2]
[Accel Time 2] / [Decel Time 2]
1
1
0
[Preset Freq 3]
[Accel Time 2] / [Decel Time 2]
0
0
1
[Preset Freq 4]
[Accel Time 1] / [Decel Time 1]
1
0
1
[Preset Freq 5]
[Accel Time 1] / [Decel Time 1]
0
1
1
[Preset Freq 6]
[Accel Time 2] / [Decel Time 2]
1
1
1
[Preset Freq 7]
[Accel Time 2] / [Decel Time 2]
(2) When a Digital Input is set to “Accel 2 & Decel 2”, and the input is active, that input overrides the settings in this table.
A078 [Jog Frequency]
0.0/[Maximum Freq]
A079 [Jog Accel/Decel]
0.1/600.0 Secs
A080 [DC Brake Time]
0.0/99.9 Secs
A setting of 99.9 Secs = Continuous
A081 [DC Brake Level]
0.0/(Drive Amps × 1.8)
A082 [DB Resistor Sel]
0/99
0.1 Hz
0.1 Secs
0.1 Secs
A083 [S Curve %]
0/100%
A084 [Boost Select]
0/14
Only active when A125 [Torque Perf Mode] is
set to 0 “V/Hz”.
1%
Settings in % of base voltage.
0 = “Custom V/Hz”
Variable Torque Constant Torque
1 = “30.0, VT”
5 = “0.0, no IR”
2 = “35.0, VT”
6 = “0.0”
3 = “40.0, VT”
7 = “2.5, CT”
4 = “45.0, VT”
8 = “5.0, CT”
9 = “7.5, CT”
0.1 Amps
0 = “Disabled”
1 = “Normal RA Res”
10.0 Hz
10.0 Secs
0.0 Secs
2 = “NoProtection”
3-99 = % of Duty Cycle
Amps × 0.05
0
0% (Disabled)
8
7 4-11 kW
(5-15 HP)
10 = “10.0, CT”
11 = “12.5, CT”
12 = “15.0, CT”
13 = “17.5, CT”
14 = “20.0, CT”
English-18
No.
Parameter
See the PowerFlex 40 User Manual on CD for more information on parameters.
Min/Max
Display/Options
Default
A085 [Start Boost]
0.1%
0.0/25.0%
Only active when A084 [Boost Select] and A125 [Torque Perf Mode] are set to “0”.
A086 [Break Voltage]
0.1%
0.0/100.0%
Only active when A084 [Boost Select] and A125 [Torque Perf Mode] are set to “0”.
A087 [Break Frequency]
0.1 Hz
0.0/400.0 Hz
A088
A089
A090
A091
A092
A093
A094
Only active when A084 [Boost Select] and A125 [Torque Perf Mode] are set to “0”.
[Maximum Voltage] 20/Rated Volts
1 VAC
[Current Limit 1]
0.1/(Drive Amps × 1.8) 0.1 Amps
[Motor OL Select]
0/2
0 = “No Derate”
1 = “Min Derate”
2 = “Max Derate”
[PWM Frequency]
2.0/16.0 kHz
0.1 kHz
[Auto Rstrt Tries]
0/9
1
[Auto Rstrt Delay]
0.0/300.0 Secs
0.1 Secs
[Start At PowerUp]
0/1
0 = “Disabled”
1 = “Enabled”
2.5%
25.0%
15.0 Hz
Rated Volts
Amps × 1.5
0
4.0 kHz
0
1.0 Secs
0
A095 [Reverse Disable]
0/1
0 = “Rev Enabled”
1 = “Rev Disabled”
0
A096 [Flying Start En]
A097 [Compensation]
0/1
0/3
1 = “Enabled”
2 = “Mechanical”
3 = “Both”
0
1
A098 [SW Current Trip]
A099 [Process Factor]
A100 [Fault Clear]
0.0/(Drive Amps × 2)
0.1/999.9
0/2
0 = “Disabled”
0 = “Disabled”
1 = “Electrical”
0.1 Amps
0.1
0 = “Ready/Idle”
0 = “Unlocked”
1 Hex
0 = “1200”
1 = “2400”
2 = “4800”
1 = “Locked”
A101 [Program Lock]
0/9999
A102 [Testpoint Sel]
400/FFFF
A103 [Comm Data Rate]
0/5
Power to drive must be cycled before any
changes will affect drive operation.
A104 [Comm Node Addr] 1/247
Power to drive must be cycled before any
changes will affect drive operation.
A105 [Comm Loss Action] 0/3
A106 [Comm Loss Time] 0.1/60.0 Secs
A107 [Comm Format]
0/5
Power to drive must be cycled before any
changes will affect drive operation.
A108 [Language]
1/10
1 = “Reset Fault”
2 = “Clear Buffer”
3 = “9600”
4 = “19.2K”
5 = “38.4K”
1
0.0 (Disabled)
30.0
0
0
400
3
100
0 = “Fault”
1 = “Coast Stop”
0.1 Secs
0 = “RTU 8-N-1”
1 = “RTU 8-E-1”
2 = “RTU 8-O-1”
2 = “Stop”
3 = “Continu Last”
6 = “Reserved”
7 = “Português”
8 = “Reserved”
9 = “Reserved”
10 = “Nederlands”
3 = “RTU 8-N-2”
4 = “RTU 8-E-2”
5 = “RTU 8-O-2”
0
5.0 Secs
0
A109 [Anlg Out Setpt]
A110 [Anlg In 0-10V Lo]
0.0/100.0%
0.0/100.0%
1 = “English”
2 = “Français”
3 = “Español”
4 = “Italiano”
5 = “Deutsch”
0.1%
0.1%
A111 [Anlg In 0-10V Hi]
0.0/100.0%
0.1%
100.0%
A112 [Anlg In4-20mA Lo]
0.0/100.0%
0.1%
0.0%
A113 [Anlg In4-20mA Hi]
0.0/100.0%
0.1%
100.0%
A114
A115
A116
A117
A118
A119
A120
0.0/10.0 Hz
0.00/99.99
0.00/99.99
0/1
0.1/(Drive Amps × 1.8)
0/400 Hz
0.0/30.0 Hz
0.1 Hz
0.01
0.01
0 = “Disabled”
0.1 Amps
1 Hz
0.1 Hz
2.0 Hz
0.00
0.00
1
Amps × 1.5
0 Hz
0.0 Hz
[Slip Hertz @ FLA]
[Process Time Lo]
[Process Time Hi]
[Bus Reg Mode]
[Current Limit 2]
[Skip Frequency]
[Skip Freq Band]
1
0.0%
0.0%
1 = “Enabled”
English-19
See the PowerFlex 40 User Manual on CD for more information on parameters.
No.
Min/Max
Display/Options
A121 [Stall Fault Time]
Parameter
0/5
0/6
3 = “360 Seconds”
4 = “480 Seconds”
5 = “Flt Disabled”
4 = “Min Freq Ref”
5 = “Max Freq Ref”
6 = “Int Freq Ref”
0
A122 [Analog In Loss]
A123 [10V Bipolar Enbl]
A124 [Var PWM Disable]
0/1
0/1
0 = “60 Seconds”
1 = “120 Seconds”
2 = “240 Seconds”
0 = “Disabled”
1 = “Fault (F29)”
2 = “Stop”
3 = “Zero Ref”
0 = “Uni-Polar In”
0 = “Enabled”
Default
1 = “Bi-Polar In”
1 = “Disabled”
0
0
A125 [Torque Perf Mode]
0/1
0 = “V/Hz”
1 = “Sensrls Vect”
1
A126 [Motor NP FLA]
A127 [Autotune]
0.1/(Drive Amps × 2)
0/2
A128
A129
A130
A131
A132
0.0/230.0 VAC
0.00/[Motor NP FLA]
0.0/400.0
0.0/400.0
0/8
A133 [PID Feedback Sel]
0/2
A134
A135
A136
A137
A138
A139
A140A147
[PID Prop Gain]
[PID Integ Time]
[PID Diff Rate]
[PID Setpoint]
[PID Deadband]
[PID Preload]
[Stp Logic 0-7]
0.00/99.99
0.0/999.9 Secs
0.00/99.99 (1/Secs)
0.0/100.0%
0.0/10.0%
0.0/400.0 Hz
0001/bAFF
A150A157
A160
A161
A162
A163
A164
A165
A166
[Stp Logic Time 0-7] 0.0/999.9 Secs
0.1 Amps
0 = “Ready/Idle”
2 = “Rotate Tune”
1 = “Static Tune”
0.1 VAC
0.01 Amps
0.1
0.1
0 = “PID Disabled”
5 = “Setpnt, Trim”
1 = “PID Setpoint”
6 = “0-10V, Trim”
2 = “0-10V Input”
7 = “4-20mA, Trim”
3 = “4-20mA Input”
8 = “Comm, Trim”
4 = “Comm Port”
0 = “0-10V Input”
2 = “Comm Port”
1 = “4-20mA Input”
0.01
0.1 Secs
0.01 (1/Secs)
0.1%
0.1%
0.1 Hz
4 Digits
For a list of digit options, refer to the PowerFlex 40
User Manual on the CD supplied with the drive.
0.1 Secs
[EM Brk Off Delay]
[EM Brk On Delay]
[MOP Reset Sel]
[DB Threshold]
[Comm Write Mode]
[Anlg Loss Delay]
[Analog In Filter]
0.01 Secs
0.01 Secs
0 = “Zero MOP Ref”
0.0%
0 = “Save”
0.1 Secs
1
[IR Voltage Drop]
[Flux Current Ref]
[PID Trim Hi]
[PID Trim Lo]
[PID Ref Sel]
0.01/10.00 Secs
0.01/10.00 Secs
0/1
0.0/110.0%
0/1
0.0/20.0 Secs
0/14
1 = “Save MOP Ref”
1 = “RAM Only”
0
Rated Amps
0
Rated Volts
Rated Amps
60.0
0.0
0
0
0.01
0.1 Secs
0.01 (1/Secs)
0.0%
0.0%
0.0 Hz
00F1
30.0 Secs
2.00 Secs
2.00 Secs
1
100.0%
0
0.0 Secs
0
English-20
Fault Codes
To clear a fault, press the Stop key, cycle power or set A100 [Fault Clear] to 1 or
2.
No.
Fault
Description
F2
F3
F4
F5
Auxiliary Input(1)
Power Loss
UnderVoltage(1)
OverVoltage(1)
F6
Motor Stalled(1)
F7
Motor Overload(1)
F8
Heatsink OvrTmp(1)
F12
HW OverCurrent
Check remote wiring.
Monitor the incoming AC line for low voltage or line power interruption.
Monitor the incoming AC line for low voltage or line power interruption.
Monitor the AC line for high line voltage or transient conditions. Bus overvoltage can also be
caused by motor regeneration. Extend the decel time or install dynamic brake option.
Increase [Accel Time x] or reduce load so drive output current does not exceed the current set
by parameter A089 [Current Limit].
An excessive motor load exists. Reduce load so drive output current does not exceed the
current set by parameter P033 [Motor OL Current].
Check for blocked or dirty heat sink fins. Verify that ambient temperature has not exceeded 40°C
(104°F) for IP 30/NEMA 1/UL Type 1 installations or 50°C (122°F) for Open type installations.
Check fan.
Check programming. Check for excess load, improper DC boost setting, DC brake volts set too
high or other causes of excess current.
Check the motor and external wiring to the drive output terminals for a grounded condition.
An analog input is configured to fault on signal loss. A signal loss has occurred.
Correct the cause of the fault and manually clear.
Check the wiring between the drive and motor. Check motor for grounded phase.
Replace drive if fault cannot be cleared.
F13
F29
F33
F38
F39
F40
F41
F42
F43
F48
Ground Fault
Analog Input Loss(1)
Auto Rstrt Tries
Phase U to Gnd
Phase V to Gnd
Phase W to Gnd
Phase UV Short
Check the motor and drive output terminal wiring for a shorted condition.
Replace drive if fault cannot be cleared.
Phase UW Short
Phase VW Short
Params Defaulted
The drive was commanded to write default values to EEPROM. Clear the fault or cycle power to
the drive. Program the drive parameters as needed.
(1)
F63 SW OverCurrent
Check load requirements and A098 [SW Current Trip] setting.
F64 Drive Overload
Reduce load or extend Accel Time.
F70 Power Unit
Cycle power. Replace drive if fault cannot be cleared.
F71 Net Loss
The communication network has faulted.
F80 SVC Autotune
The autotune function was either cancelled by the user of failed.
F81 Comm Loss
If adapter was not intentionally disconnected, check wiring to the port. Replace wiring, port
expander, adapters or complete drive as required. Check connection. An adapter was
intentionally disconnected. Turn off using A105 [Comm Loss Action].
F100 Parameter Checksum Restore factory defaults.
F122 I/O Board Fail
Cycle power. Replace drive if fault cannot be cleared.
(1)
Auto-Reset/Run type fault. Configure with parameters A092 and A093.
English-21
Drive Dimensions
PowerFlex 40 Frames – Ratings are in kW and (HP)
Frame 120V AC – 1-Phase 240V AC – 1-Phase 240V AC – 3-Phase 480V AC – 3-Phase 600V AC – 3-Phase
B
0.4 (0.5)
0.75 (1.0)
1.1 (1.5)
0.4 (0.5)
0.75 (1.0)
1.5 (2.0)
2.2 (3.0)
C(1)
(1)
0.4 (0.5) 2.2 (3.0)
0.75 (1.0) 3.7 (5.0)
1.5 (2.0)
5.5 (7.5)
7.5 (10.0)
0.4 (0.5) 2.2 (3.0)
0.75 (1.0) 4.0 (5.0)
1.5 (2.0)
5.5 (7.5) 11.0 (15.0)
7.5 (10.0)
0.75 (1.0) 4.0 (5.0)
1.5 (2.0)
2.2 (3.0)
5.5 (7.5) 11.0 (15.0)
7.5 (10.0)
IP66, NEMA/UL Type 4X rated drives are not availble in Frame C drive ratings.
IP20, NEMA/UL Type Open
Dimensions are in millimeters and (inches).
Weights are in kilograms and (pounds).
C
D
Frame
A
F
E
B
B
C
A
B
C
D
E
F
100
(3.94)
130
(5.1)
180
(7.09)
260
(10.2)
136
(5.35)
180
(7.1)
87
(3.43)
116
(4.57)
168
87.4
(6.61) (3.44)
246
–
(9.7)
Ship
Weight
2.2
(4.9)
4.3
(9.5)
5.5 (0.22)
Communication, RFI Filter, IP 30/NEMA 1/UL Type 1 Option Kits
B
107.0 (4.21)
66.0 (2.60)
24.0 (0.94)
79.1 (3.11)
64.1 (2.52)
40.6 (1.60)
A
25.6 (1.01)
∅ 22.2
(0.87)
109.9
(4.33)
111.2
(4.38)
74.3
(2.93)
B Frame - 22-JBAB
C Frame - 22-JBAC
108.7 (4.28)
92.2 (3.63)
69.2 (2.72)
45.7 (1.80)
D
77.5 (3.05)
Dimension
50.0 (1.97)
A
B
C
D
Option
Comm Cover
EMC Line Filter
EMC Line Filter
IP30/NEMA 1/UL
Type 1
IP30/NEMA 1/UL
Type 1 for Comm
Cover
∅ 22.2
(0.87)
152.2
(5.99)
C
22.5 (0.89)
∅ 28.5
(1.12)
22.2 (0.87)
∅ 22.2
(0.87)
∅ 28.5
(1.12)
∅ 22.2
(0.87)
B Frame C Frame
Drive
Drive
25 (0.98)
50 (1.97)
229 (9.02)
33 (1.30)
25 (0.98)
60 (2.36)
309 (12.17)
60 (2.36)
64 (2.52)
60 (2.36)
179.8
(7.08)
134.3
(5.29)
144.8
(5.70)
105.3
(4.15)
109.8
(4.32)
76.3
(3.00)
B Frame - 22-JBCB
C Frame - 22-JBCC
(used with Comm Cover)
(used with Comm Cover)
English-22
IP66, NEMA Type/UL Type 4X – Dimensions are in millimeters and (inches) Weights are
in kilograms and (pounds).
165
(6.50)
146
(5.75)
6.5
(0.26)
46
(1.81)
23
(0.91)
270
(10.63)
198
(7.80)
253
(9.96)
28
(1.10)
124
(4.88)
89
(3.50)
22
(0.87)
82.5
(3.25)
Weight
5.2 (11.5)
www.rockwellautomation.com
Power, Control and Information Solutions Headquarters
Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA,Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe/Middle East/Africa: Rockwell Automation, Vorstlaan/Boulevard du Souverain 36, 1170 Brussels, Belgium,Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong,Tel: (852) 2887 4788, Fax: (852) 2508 1846
Publication 22B-QS001D-EN-P – January 2007
Supersedes October 2005
Copyright © 2007 Rockwell Automation, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement