2 - Servos e Inversores

2 - Servos e Inversores
Vision Sensor
FH Series
Vision System
Operation Manual for Sysmac Studio
[email protected]@@
[email protected]@@
Z343-E1-01
Introduction
Thank you for purchasing the FH.
This manual provides information regarding functions, performance and operating methods that
are required for using the FH.
When using the FH, be sure to observe the following:
• The FH must be operated by personnel knowledgeable in electrical engineering.
• To ensure correct use, please read this manual thoroughly to deepen your understanding of the
product.
• Please keep this manual in a safe place so that it can be referred to whenever necessary.
About copyright and trademarks
IJG Code is copyright (C) 1991, 2011, Thomas G. Lane, Guido Vollbeding.
This software is based in part on the work of the Independent JPEG Group.
• Sysmac and SYSMAC are trademarks or registered trademarks of OMRON Corporation in Japan and other
countries for OMRON factory automation products.
• EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.
• ODVA, CIP, CompoNet, DeviceNet, and EtherNet/IP are trademarks of ODVA.
• The SD and SDHC logos are trademarks of SD-3C, LLC.
• QR Code is a registered trademark of DENSO WAVE INCORPORATED in JAPAN and other countries.
Manual Structure
Manual Structure
Page Structure
The following page structure is used in this manual.
Mounting Units
Level 1 heading
Level 2 heading
Level 3 heading
Connecting Controller Components
Gives the current
headings.
4 Installation and Wiring
Level 2 heading
Level 3 heading
4-3
4-3-1
The Units that make up an NJ-series Controller can be connected simply by pressing the Units together
and locking the sliders by moving them toward the back of the Units. The End Cover is connected in the
same way to the Unit on the far right side of the Controller.
A step in a procedure
1
Join the Units so that the connectors fit exactly.
Hook
Indicates a procedure.
Hook holes
Connector
4-3 Mounting Units
4
The yellow sliders at the top and bottom of each Unit lock the Units together. Move the sliders
toward the back of the Units as shown below until they click into place.
Move the sliders toward the back
until they lock into place.
Lock
Release
Slider
Special information
Icons indicate
precautions, additional
information, or reference
information.
Manual name
4-3-1 Connecting Controller Components
2
Page tab
Gives the number
of the main section.
Precautions for Correct Use
The sliders on the tops and bottoms of the Power Supply Unit, CPU Unit, I/O Units, Special I/O
Units, and CPU Bus Units must be completely locked (until they click into place) after connecting
the adjacent Unit connectors.
NJ-series CPU Unit Hardware User’s Manual (W500)
4-9
This illustration is provided only as a sample. It may not literally appear in this manual.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
1
Manual Structure
Special Information
Special information in this manual is classified as follows:
Precautions for Safe Use
Precautions on what to do and what not to do to ensure safe usage of the product.
Precautions for Correct Use
Precautions on what to do and what not to do to ensure proper operation and performance.
Additional Information
Additional information to read as required.
This information is provided to increase understanding or make operation easier.
Version Information
Information on differences in specifications and functionality for CPU Units with different unit
versions and for different versions of the Sysmac Studio is given.
Note References are provided to more detailed or related information.
Terminology
• For descriptions of the Controller terms that are used in this manual, refer to information on terminology in the NJ-series CPU Unit Software User’s Manual (Cat. No. W501) and the NJ-series CPU Unit
Hardware User’s Manual (Cat. No. W500).
• For descriptions of the FH/FZ5 Sensor controller terms that are used in this manual, refer to information on terminology in the Vision System FH/FZ5 series User's Manual (Cat. No. Z340).
2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Sections in this Manual
Sections in this Manual
1
2
Overview
Basic Operations
10
A
1
10
2
A
3
I
Troubleshooting
Appendices
4
3
Connecting with
a Vision Sensor
4
Configuraing Measurement Settings
6
5
Designing Exchange with External Devices
7
6
I
Index
5
8
Online Debugging
9
7
Offline Debugging
8
Other Useful Functions
9
Limitations
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3
Related Manuals
Related Manuals
The following manuals are related to the FH-series Sensor Controllers. Use these manuals for reference.
Manual name
Cat. No.
Vision System FH Series
Operation Manual for
Sysmac Studio (This
manual)
Z343
Sysmac Studio Version 1
Operation Manual
W504
Vision System FH/FZ5
Series User's Manual
Z340
Model numbers
Application
Description
Learning about how to configure settings for and
operate the sensor controller for the FH Series from
the Sysmac Studio FH
Tools
In this manual, we will describe how to configure
settings for and operate the sensor controller for
the FH Series from the Sysmac Studio FH Tools.
[email protected]@@
Learning about the operating procedures and functions of the Sysmac Studio
Describes the operating procedures of the Sysmac Studio.
[email protected]@@
Learning about how to configure settings for the
FH/FZ5 Series Vision Sensors
In this manual, we will describe how to configure
settings using the sensor controller for the
FH/FZ5 Series Vision Sensors.
Learning about how to configure settings for processing items for the FH/FZ5
Series Vision Sensors
In this manual, we will describe how to configure
settings for processing items for the FH/FZ5
Series Vision Sensors.
Learning about how to configure communications settings for the FH/FZ5 Series
Vision Sensors
In this manual, we will describe how to configure
communications settings using the sensor controller for the FH/FZ5 Series Vision Sensors.
[email protected]@@
[email protected]@@
[email protected]@@
[email protected]
[email protected]@
[email protected]@
Vision System FH/FZ5
Series Processing Item
Function Reference Manual
Z341
[email protected]@@
[email protected]@@
[email protected]
[email protected]@
[email protected]@
Vision System FH/FZ5
Series User's Manual for
Communications Settings
Z342
[email protected]@@
[email protected]@@
[email protected]
[email protected]@
[email protected]@
4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Related Manuals
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
5
CONTENTS
CONTENTS
Introduction
Manual Structure ...................................................................................................... 1
Page Structure ............................................................................................................................................. 1
Special Information ...................................................................................................................................... 2
Terminology ................................................................................................................................................. 2
Sections in this Manual ........................................................................................... 3
Related Manuals ....................................................................................................... 4
Manual Revision History.......................................................................................... 9
Section 1
Overview
1-1
Supported Models ................................................................................................................. 1-2
1-2
Project Management ............................................................................................................. 1-3
Section 2
Basic Operations
2-1
Basic Design Flow 1.............................................................................................................. 2-2
2-2
Basic Design Flow 2.............................................................................................................. 2-4
2-3
Creating a New Project ......................................................................................................... 2-5
2-3-1
2-3-2
2-3-3
2-4
Description of Screen Components..................................................................................... 2-8
2-4-1
2-4-2
2-4-3
2-4-4
2-4-5
2-4-6
2-5
Adding a Processing Unit.......................................................................................................... 2-27
Managing Processing Units ...................................................................................................... 2-28
Searching for a Processing Unit................................................................................................ 2-30
Function List ........................................................................................................................ 2-31
2-7-1
2-7-2
6
Switching Scenes...................................................................................................................... 2-22
Managing Scenes ..................................................................................................................... 2-22
Entering Scene Information....................................................................................................... 2-23
Searching for a Scene............................................................................................................... 2-23
Switching Scene Groups........................................................................................................... 2-23
Managing Scene Groups .......................................................................................................... 2-24
Entering Scene Group Information............................................................................................ 2-25
Basic Operations of Flow Editing ...................................................................................... 2-26
2-6-1
2-6-2
2-6-3
2-7
Application Window..................................................................................................................... 2-8
Menu Bar..................................................................................................................................... 2-9
Toolbar ........................................................................................................................................ 2-9
Multiview Explorer ..................................................................................................................... 2-10
Edit Pane................................................................................................................................... 2-11
Toolbox...................................................................................................................................... 2-20
Basic Operations of Scene Data ........................................................................................ 2-21
2-5-1
2-5-2
2-5-3
2-5-4
2-5-5
2-5-6
2-5-7
2-6
Creating a New Project File from the Project Window ................................................................ 2-5
Adding FH Device to a Project .................................................................................................... 2-7
Deleting FH Device from a Project.............................................................................................. 2-7
List of Functions Provided with the FH Tool .............................................................................. 2-31
Comparison with FH Series Unit Functions .............................................................................. 2-33
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
CONTENTS
Section 3
3-1
3-2
Connecting with a Vision Sensor
Adding FH Series Vision Sensor on the Network to a Project .......................................... 3-3
Establishing an Online Connection with a Vision Sensor ................................................. 3-4
3-2-1
3-2-2
Establishing an Online Connection from the Sensor Connection Screen................................... 3-4
Establishing an Online Connection from the Multiview Explorer ................................................ 3-6
3-3
Transferring Project Data to a Sensor ................................................................................. 3-7
3-4
Ending a Connection with a Vision Sensor ........................................................................ 3-8
3-4-1
3-4-2
Section 4
4-1
Configuring Measurement Settings
Overview of Processing Units .............................................................................................. 4-2
4-1-1
4-1-2
4-1-3
4-1-4
4-1-5
4-1-6
4-1-7
4-2
Section 5
Setting Procedure.................................................................................................................. 5-3
Online Debugging
Performing Test Measurement ............................................................................................. 6-2
6-1-1
6-1-2
6-1-3
6-2
Parameter Settings ..................................................................................................................... 4-5
Editing an Area ........................................................................................................................... 4-6
Color Extraction .......................................................................................................................... 4-9
Color ......................................................................................................................................... 4-10
Binary........................................................................................................................................ 4-10
Detection Point/Reference Point................................................................................................4-11
List .............................................................................................................................................4-11
Image Control Area....................................................................................................................4-11
Designing Exchange with External Devices
Section 6
6-1
Input Image................................................................................................................................. 4-2
Measurement.............................................................................................................................. 4-2
Compensate Image .................................................................................................................... 4-2
Support Measurement ................................................................................................................ 4-3
Branch ........................................................................................................................................ 4-3
Output Result.............................................................................................................................. 4-3
Display Result............................................................................................................................. 4-3
Editing a Processing Unit ..................................................................................................... 4-4
4-2-1
4-2-2
4-2-3
4-2-4
4-2-5
4-2-6
4-2-7
4-2-8
5-1
Ending a Connection in the Sensor Connection Screen............................................................. 3-8
Ending a Connection in the Multiview Explorer .......................................................................... 3-9
Measuring Camera Images ........................................................................................................ 6-2
Measuring File Images in the RAMDisk or USB Memory of the Vision Sensor.......................... 6-3
Measuring Logging Images in the Vision Sensor Memory ......................................................... 6-3
Checking Measurement Results .......................................................................................... 6-4
6-2-1
6-2-2
6-2-3
Checking Detailed Results.......................................................................................................... 6-4
Changing the Image Display Settings......................................................................................... 6-6
Checking Multiple Measurement Images at the Same Time ...................................................... 6-6
6-3
Checking Result Output........................................................................................................ 6-7
6-4
Saving Measurement Results............................................................................................... 6-8
6-5
Saving Settings Data ............................................................................................................. 6-9
Section 7
7-1
Offline Debugging
Performing Offline Simulation of Sensor Measurement Operation .................................. 7-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
7
CONTENTS
Section 8
Other Useful Functions
8-1
Using the Command Customize Setting Tool ..................................................................... 8-2
8-2
Using the Calibration Support Tool ..................................................................................... 8-3
8-3
Using the File Save Tool ....................................................................................................... 8-4
8-3-1
8-3-2
8-3-3
Opening the File Save Tool ......................................................................................................... 8-4
Copying a File ............................................................................................................................. 8-4
Saving a Logging Image as a File............................................................................................... 8-6
8-4
Using the User Data Setting Tool ......................................................................................... 8-7
8-5
Changing the System Environment ..................................................................................... 8-8
8-6
Help....................................................................................................................................... 8-10
Section 9
9-1
Limitations
Limitations.............................................................................................................................. 9-2
Section 10
Troubleshooting
10-1 Troubleshooting for the EtherCAT ..................................................................................... 10-2
10-2 Sysmac Error Status ........................................................................................................... 10-3
Appendices
A-1 Sysmac Device Features ......................................................................................................A-2
A-1-1
A-1-2
A-1-3
A-1-4
A-1-5
Sysmac Error Status ...................................................................................................................A-2
Saving the Node Address Setting ...............................................................................................A-3
Serial Number Display ................................................................................................................A-4
Compliance with ESI Specification (ETG.2000 S (R) V1.0.1)......................................................A-4
SII Data Check ............................................................................................................................A-4
Index
8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Manual Revision History
Manual Revision History
The manual revision symbol is appended to the manual number on the front cover and back cover.
Z343-E1-01
Revision Symbol
Revision Symbol
01
Revision Date
June 2013
Reason for Revision and Revised Page
First edition
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
9
Manual Revision History
10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
1
Overview
This document describes the functional specifications of the Sysmac Studio FH tools
(hereinafter referred to as "FH tools").
1-1 Supported Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-2 Project Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
1-1
1 Overview
1-1
Supported Models
The FH tool supports the following models in the FH Vision Sensor series.
Connection Device Type
FH-3050
FH-3050-10
FH-3050-20
FH-1050
FH-1050-10
FH-1050-20
1-2
Description
High-speed controller for 2-channel camera type
High-speed controller for 4-channel camera type
High-speed controller for 8-channel camera type
Standard controller for 2-channel camera type
Standard controller for 4-channel camera type
Standard controller for 8-channel camera type
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
1 Overview
Project Management
Sysmac Studio manages the configuration Information of each of the controller, servo, and vision sensor devices on a project basis.
One FH vision sensor series device can be registered to one project. With the FH vision sensor series,
the following data is managed as project data.
• Scene group data (scene data)
• System data
• Tool data
With the FH vision sensor series, you can use multiple multi-line random-trigger modes. The data
above is managed on a line basis for multiple multi-line random-trigger modes.
Project data manages these data together as one batch. These data can also be exported and imported
individually as file data.
Project data
FH sensor
Line
Line
Line
Scene group data
Scene group data
Scene group data
Scene data
Scene data
Scene data
Tool data
Command
customize
data
System
data
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
1-3
1-2 Project Management
1-2
1
1 Overview
1-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2
Basic Operations
This chapter describes the basic design flow and design items for using Sysmac Studio.
2-1 Basic Design Flow 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2-2 Basic Design Flow 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2-3 Creating a New Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-3-1
2-3-2
2-3-3
Creating a New Project File from the Project Window . . . . . . . . . . . . . . . . . . . 2-5
Adding FH Device to a Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Deleting FH Device from a Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-4 Description of Screen Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2-4-1
2-4-2
2-4-3
2-4-4
2-4-5
2-4-6
Application Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Multiview Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Edit Pane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
2-5 Basic Operations of Scene Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
2-5-1
2-5-2
2-5-3
2-5-4
2-5-5
2-5-6
2-5-7
Switching Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Managing Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Scene Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Scene Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Managing Scene Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering Scene Group Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-22
2-22
2-23
2-23
2-23
2-24
2-25
2-6 Basic Operations of Flow Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
2-6-1
2-6-2
2-6-3
Adding a Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Managing Processing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Searching for a Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
2-7 Function List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
2-7-1
2-7-2
List of Functions Provided with the FH Tool . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Comparison with FH Series Unit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-1
2 Basic Operations
2-1
Basic Design Flow 1
This section describes the flow for designing a system that uses NJ-series CPU Unit as a controller.
For details on the program on the NJ-series CPU Unit side, task design, and debugging, refer to the
Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later).
z New project settings
Create a project file.
1
Starting Sysmac Studio
Start Sysmac Studio.
Refer to "3-3-1 Starting and Exiting the Sysmac Studio" in the Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later.)
2
Designing a new project
Create a new project.
Refer to "3-3-2 Creating a Project File" in the Sysmac Studio Version 1 Operation Manual (Cat.
No. W504-E1-08 or later.)
z Controller configuration and settings
• Controller configuration
(1) Creating an EtherCAT configuration
Register FH as an EtherCAT slave in [EtherCAT].
Refer to "5-1 EtherCAT Configuration and Settings" in the Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later.)
(2) Registering device variables
When using or using after editing device variables for the user defined variables to connect
the FH I/O information and program, register the device variables in [I/O Map].
Refer to "4-1-2 Creating Device Variables" in the Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later.)
• Controller settings
(1) Editing slave parameters
Edit the Operation Settings of the slaves.
Refer to "5-2-1 Creating the EtherCAT Slave Terminal Configulation" in the Sysmac Studio
Version 1 Operation Manual (Cat. No. W504-E1-08 or later.)
z Sensor connection
Establish an online connection with the sensor.
(1) Connecting a sensor
Refer to Section 3 Connecting with a Vision Sensor
2-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
z Design
Create the processing flow.
2-1 Basic Design Flow 1
(1) Creating flow
Refer to 2-6 Basic Operations of Flow Editing on page 2-26
(2) Editing processing units
Refer to 4-2 Editing a Processing Unit on page 4-4
z Online debugging of sensor
Perform debugging using the actual device.
(1) Performing test measurement
2
Perform test measurement on sample work. Adjust the parameters if necessary.
Refer to Section 6 Online Debugging
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-3
2 Basic Operations
2-2
Basic Design Flow 2
This section describes the flow for designing a system that uses a controller other than NJ-series CPU
Unit.
z New project settings
Create a project file.
(1) Starting Sysmac Studio
Start Sysmac Studio.
Refer to "3-3-1 Starting and Exiting the Sysmac Studio" in the Sysmac Studio Version 1
Operation Manual (Cat. No. W504-E1-08 or later.)
(2) Designing a new project
Create a new project.
Select a vision sensor for the category and FH for the device.
Refer to 2-3 Creating a New Project on page 2-5
(3) Selecting sensor type
Select the sensor type and then establish an online connection.
Refer to step 3 on P. 2-6 of 2-3 Creating a New Project on page 2-5
z Sensor configuration and settings
• Sensor configuration
(1) Creating an interface configuration for the sensor
Edit the interface configuration.
Refer to 5-1 Setting Procedure on page 5-3
• Sensor settings
(1) Editing the communication conditions
Edit the communication conditions of the sensor.
Refer to 5-1 Setting Procedure on page 5-3
z Design
Create the processing flow.
(1) Creating flow
Refer to 2-6 Basic Operations of Flow Editing on page 2-26
(2) Editing processing units
Refer to 4-2 Editing a Processing Unit on page 4-4
z Online debugging
Perform debugging using the actual device.
(1) Performing test measurement
Perform test measurement on sample work. Adjust the parameters if necessary.
Refer to Section 6 Online Debugging
2-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-3
Creating a New Project
Here, we describe how to create a new project for the FH vision sensor (hereinafter referred to as "FH
project").
2-3-1
Creating a New Project File from the Project Window
1
2
2
Click the [New Project] button in the project window.
Setting
Vision sensor
FH
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-5
2-3-1 Creating a New Project File from the Project Window
In the [Project Properties] dialog box, enter the information in [Project name], [Author] (optional),
and [Comment] (optional), select the following device from [Category] and [Device] of [Select
Device], and click the [Create] button.
Item
Category
Device
2-3 Creating a New Project
This section describes how to create a new project file. For details on the basic operations, refer to "3-3
Creating a Project" in the Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later).
2 Basic Operations
3
Select the FH vision sensor to which you connect.
When establishing an online connection, click [Search for sensors] and then click the [Search]
button. The found sensors are displayed in a list. Select the sensor you wish to connect to and
then click the [OK] button.
If you know the IP address of the sensor you wish to connect to beforehand or will connect to a
sensor via a router, select the [Specify the IP address] check box and then enter the IP address
in [IP address]. After input is complete, click the [OK] button.
If you wish to edit the settings offline, click [Enter the type], select the [Type] and [Version] items
for the sensor you wish to edit, and then click the [OK] button.
4
A new project is created.
The project file is created and the next screen appears.
Precautions for Correct Use
An online connection cannot be established if the FH device registered to the project and the
actual device are not the same type and version.
2-6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-3-2
Adding FH Device to a Project
2-3 Creating a New Project
You can add an FH device to a project.
Right-click the Device Group and select [Add | FH].
2
The sensor selection screen appears. Select the sensor type.
The selected FH device is registered.
2-3-2 Adding FH Device to a Project
Precautions for Correct Use
Only one FH device can be added to a project.
If multiple FH devices are registered, "
devices.
2-3-3
" is displayed in the type field of the invalid FH
Deleting FH Device from a Project
You can delete FH device from a project.
Right-click the FH vision sensor you wish to delete and select [Delete].
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-7
2 Basic Operations
2-4
Description of Screen Components
This section describes the screen components in FH project.
For a description of the screen components in NJ-series CPU Unit project, refer to "3-4 Parts of the
Window" in the Sysmac Studio Version 1 Operation Manual (Cat. No. W504-E1-08 or later.)
2-4-1
Application Window
1)
2)
3)
4)
No.
1
2
3
4
5
2-8
5)
Name
Menu Bar
Toolbar
Multiview Explorer
Edit Pane
Toolbox
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
Menu Bar
File
Insert
Tools
Help Contents
Help
2-4-3
Online Registration
Keyboard Mapping Reference
About Sysmac Studio
Description
Closes the project.
Saves the project.
Saves the project with a different name.
Saves the project with a new update number.
Imports an exported file so that it can be edited in the tool.
Saves the project as an external file.
Sets the print attributes (margins and other attributes).
Executes the print command.
Closes Sysmac Studio.
Copies the selected item.
Pastes the copied item.
Deletes the selected item.
Inserts an NJ301 or NJ501 project.
Inserts an FQ-M or FH project.
Inserts a ZW project.
Displays the Options menu.
Displays “Vision System FH Series Operation Manual Sysmac Studio (Cat. No. Z343)."
Performs online registration.
Displays the shortcut key reference.
Displays the version of Sysmac Studio.
Toolbar
Button Name
Copy
Paste
Delete
Help
Description
Copies the selected item.
Pastes the copied item.
Deletes the selected item.
Displays Vision System FH Series Operation Manual Sysmac Studio
(Cat. No. Z343)
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-9
2
2-4-2 Menu Bar
Edit
Menu Name
Close
Save
Save As
Save As New Number
Import
Export
Page Settings
Print
Exit
Copy
Paste
Delete
Controller
Vision Sensor
Displacement Sensor
Options
2-4 Description of Screen Components
2-4-2
2 Basic Operations
2-4-4
Multiview Explorer
• This pane will be the access point for all data of the FH series.
• You can right-click any data item that can be set and select an item from the menu (context menu).
You can also display various editing screens in the Edit Pane.
• Multiview Explorer can be displayed or hidden by clicking the display/hide bar on the left side of the
window. Even when hidden, it can be displayed temporarily by placing the mouse pointer over the
display/hide bar. Moving the mouse pointer away from the bar returns the Multiview Explorer to the
hidden state.
List of the layers and items that make up the Multiview Explorer and the menu items displayed by
right-clicking
Tree View Items
Device Group
Type
Line X
(X=0,1,,,7)
Scene data
Menu Item
Add | FH
Rename
Edit
Delete
Online
Offline
Restart
Monitor window
Scene maintenance window
Save data
Rename
Save to file
Load from file
Edit
Save to file
Load from file
Save to file
Load from file
Edit
Edit
Description
Adds a sensor to the project.
Changes the device group name.
Displays the main screen in the Edit Pane.
Deletes the sensor from the project.
Switches the connection state with the sensor to online.
Switches the connection state with the sensor to offline.
Restarts the sensor.
Displays the monitor window in the Edit Pane.
Displays the Scene maintenance window in the Edit
Pane.
Saves the sensor settings data to non-volatile memory.
Changes the line name.
Saves scene group 0 + system data to a file.
Loads scene group 0 + system data from a file.
Displays the scene data editing screen in the Edit Pane.
Saves the scene group data to a file.
Loads the scene group data from a file.
Displays the system settings editing screen in the Edit
Pane.
Saves the system data to a file.
Loads the system data from a file.
Displays the I/O command customize tool in the Edit
Pane.
Saves the customized I/O settings data to a file.
Loads the customized I/O settings data from a file.
Displays the user data tool in the Edit Pane.
Displays the file saving tool in the Edit Pane.
Edit
Displays the calibration support tool in the Edit Pane.
Edit
System data
Communication
command
customize
Tools
2 - 10
User Data
Save file
Calibration
Support
Tool
Save to File
Load from File
Edit
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
Edit Pane
This pane is for displaying and editing the detailed data of all items.
The following nine screens are provided.
Screen
Reference Page
P. 2-11
P. 2-12
P. 2-15
2
P. 2-18
P. 2-19
2-4-5 Edit Pane
Description
This allows you to access the sensor information, the connecSensor connection screen
tion with the sensor, the main screen of each line, etc.
Monitor window
This allows you to check the measurement results.
This allows you to change the scene data settings.
Scene maintenance
It also allows you to perform test measurement and check the
window
measurement results.
Scene data editing screen This allows you to set the scene data.
System data editing screen This allows you to set the system data.
Communication command
This displays the I/O command customize tool in the Edit Pane.
customize tool screen
User Data tool screen
This allows you to edit the user data.
This allows you to copy or move files between the RAMDisk/USB memory of the sensor or between the RAMDisk/USB
memory and a PC. It also allows you to save the logging image
File Save Tool screen
stored in the vision sensor memory to the RAMDisk or USB
memory of the sensor, or to the memory of a PC.
Calibration support tool
This allows you to check the calibration settings.
screen
―
―
P. 8-4
P. 8-3
Sensor connection screen
This allows you to access the sensor information, the connection with the sensor, the main screen of
each line, etc.
Group
Sensor
information
Online
Item
Sensor name
Comment
Type
Version
Available application memory
IP address
Connect
Disconnect
Search for sensors
Sensor Restart
Initialize
Description
Allows you to change the sensor name.
Allows you to enter a comment for the sensor.
Displays the sensor type information.
Displays the sensor version information.
Displays the amount of available application memory.
Sets the IP address of the sensor for online connections.
Establishes an online connection to the sensor with the specified IP address.
Disconnects the sensor currently connected with an online connection.
Searches for sensors within the same network.
Restarts the sensor.
Initializes the sensor.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2-4 Description of Screen Components
2-4-5
2 - 11
2 Basic Operations
Additional Information
For details on the settings in the sensor connection screen, refer to 3-2 Establishing an Online
Connection with a Vision Sensor on page 3-4.
Monitor window
1)
2)
4)
5)
6)
3)
This allows you to check the measurement results.
No.
1
Status display area
2
4
5
Image display area
Image size control
section
Flow
Detail result
6
Image display settings
3
2 - 12
Screen Component
Description
Allows you to access the sensor information, the connection with
the sensor, the main screen of each line, etc.
Allows you to check the measurement results.
Reference
Page
P. 2-13
P. 2-13
Enlarges or reduces the selected image.
P. 2-13
Displays the processing flow for the relevant line or current scene.
Displays the results for the processing unit selected in the flow.
Sets the displays settings for images displayed in the image display
area.
P. 2-14
P. 2-14
P. 2-15
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2)
3)
4)
5)
1)
6)
Item
Judgment result
Processing time
3
Sensor name and IP
address
4
5
6
Line name
Scene group name
Scene name
Description
Displays the judgment result (OK or NG).
Displays the processing time for the most recent measurement process.
Displays the sensor name and IP address.
When the sensor is offline, "Offline" is displayed instead of the IP address.
Displays the line for which information is currently being displayed.
Displays the current scene group number and scene group name.
Displays the current scene number and scene name.
z Image display area
This displays the image and measurement result (graphic) for the processing unit selected in the
flow display.
The settings for image display in the image display area can be changed in the Image display settings menu. For details on the Image display settings menu, refer to Image display settings on page
2-15.
While an image is displayed enlarged, you can change the display area by left-clicking and dragging
the displayed image.
z Image size control section
This allows you to enlarge or reduce the selected image.
Button
Description
Enlarges the image. Image display is enlarged in 20% steps. (Upper limit: 1600%)
Reduces the image. Image display is reduced in 20% steps. (Lower limit: 1%)
Makes the image fit the display frame.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 13
2
2-4-5 Edit Pane
No.
1
2
2-4 Description of Screen Components
z Status display area
2 Basic Operations
Button
Description
Enlarges or reduces the image.
z Flow
This displays the processing flow for the relevant line or current scene.
If a processing unit displayed in the list is selected, the following display information is linked and so
changes accordingly.
• Image display information
• Detailed result display information
If multiple images are displayed, the display information of the image with the focus on it changes.
If a processing unit is searched in the search area, the focus moves to the found processing unit.
Item
Search
Flow list
Description
Searches for the specified processing unit from within the processing flow.
Displays the processing flow for the relevant line or current scene.
z Detail result
This displays the results for the processing unit selected in the flow.
2 - 14
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-4 Description of Screen Components
z Image display settings
Item
Image layout
Image mode
Sub image
2
Selection items: 1Form, 2Form, and 4Form
Selects the image mode for the image with the focus on it.
Selection items: Through, Freeze, and NG image
Selects position list display for the image with the focus on it.
2-4-5 Edit Pane
Positions
Description
Selects the number of images to display.
Selection items: OFF and ON
Selects the sub image number for the image with the focus on it.
Select items: Image0, Image1,..., image31
This sets the displays settings for images displayed in the image display area.
Scene maintenance window
This allows you to copy, switch, and clear scene data and scene group data.
It also allows you to perform test measurement and check the measurement results.
z Status display area
This is the same as in the monitor window. Refer to Status display area on page 2-13.
z Image display area
This is the same as in the monitor window. Refer to Image display area on page 2-13.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 15
2 Basic Operations
z File selection section
Button
Description
Displays camera images. Selection is not possible when offline.
Displays logging images. Selection is not possible when offline.
Displays file images.
When online, displays images in the RAMDisk or USB memory of the sensor.
When offline, displays images in the following folder on the PC.
C:\Documents and Settings\<User name>\My Documents\OMRON FH
Selects an image file when a file image is selected.
z Image control section
Button
Description
Performs continuous measurement of images.
In the case of camera images, continuously measures and displays camera images.
In the case of logging images, continuously measures and displays images in the
logging folder.
In the case of file images, continuously measures and displays images in the folder.
When logging images and file images are selected, continuous measurement is
stopped after all images are measured.
Stops continuous measurement.
Measures and displays the previous image.
Measures and displays the next image.
z Image size control section
This is the same as in the monitor window. Refer to Image size control section on page 2-13.
z Data save
This saves the settings data to non-volatile memory of the FH sensor.
z Measure
Performs a single measurement.
The measurement process is performed for the file image that is currently displayed.
2 - 16
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
Item
Output
Description
Outputs the measurement results to an external device when test measurement is
performed.
z Flow
This is the same as in the monitor window. Refer to Flow on page 2-14.
2-4 Description of Screen Components
z Test measurement settings
2
z Detail result
2-4-5 Edit Pane
This is the same as in the monitor window. Refer to Detail result on page 2-14.
z Image display settings
This is the same as in the monitor window. Refer to Image display settings on page 2-15.
z Scene maintenance area
Clicking the scene maintenance item bar opens the scene maintenance window.
This screen allows you to manage and switch the scene group data and scene data.
For details on the specifications, refer to 2-5 Basic Operations of Scene Data on page 2-21.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 17
2 Basic Operations
Scene data editing screen
This editing screen allows you to build the processing unit flow.
A new processing unit can be added to the flow by dragging and dropping any processing unit in the
Toolbox on to the list.
It is also possible to check the image that is the measurement target, and the measurement results
for each processing unit.
z Flow display
This displays the processing flow for the relevant line or current scene.
Each editing process (adding, copying, deleting, etc.) of the processing units in the flow can be performed.
Item
Search
Flow list
Description
Searches for the specified processing unit from within the processing flow.
Displays the processing flow for the relevant line or current scene.
The registered processing units are displayed in the flow list.
2 - 18
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-4 Description of Screen Components
z Data save
This is the same as in the Scene maintenance screen. Refer to Data save on page 2-16.
z Measure
This is the same as in the Scene maintenance screen. Refer to Measure on page 2-16.
z File selection section
This is the same as in the Scene maintenance screen. Refer to File selection section on page 2-16.
2
z Image control section
z Detail result
This is the same as in the monitor window. Refer to Detail result on page 2-14.
System data editing screen
2)
1)
3)
This editing screen allows you to set the system data.
System data is managed on a group basis and the editing items for each group are displayed by clicking the corresponding icon.
No.
1
2
3
Name
Icon
Group name display area
Editing item display area
For details on each group, refer to 8-5 Changing the System Environment on page 8-8.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 19
2-4-5 Edit Pane
This is the same as in the Scene maintenance screen. Refer to Image control section on page 2-16.
2 Basic Operations
Tool settings editing screen
The tool settings editing screen displays the editing screens of the following tools.
For details on each tool, refer to Section 8 Other Useful Functions.
Tool
Communication Command Customize setting
tool
Calibration support tool
File save tool
User data tool
2-4-6
Functional Overview
Edits custom commands.
Allows you to check the calibration settings.
Saves the image data to a file.
Allows you to edit the user data, set the initial settings, and enter a comment that
describes the data.
Toolbox
The Toolbox displays a list of the processing units that can be used.
When the scene editing screen is displayed in the Edit Pane, you can add a processing unit by selecting any processing unit and dragging and dropping it onto the flow list in the scene editing screen.
1)
2)
3)
No.
1
2
3
2 - 20
Item
Processing item search window
Processing item area
Guidance
Operation
Searches for processing items.
Displays the available processing units.
Displays an overview of the selected processing unit.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
Basic Operations of Scene Data
An FH vision sensor can handle multiple scene data.
You can perform operations such as switching, copying, and deleting scenes with the scene maintenance functions in the scene maintenance window.
Right-click [Line X] in the Multiview Explorer and select [Scene maintenance screen] from the menu.
2-5 Basic Operations of Scene Data
2-5
Click [Scene maintenance] and show [Scene maintenance] Pane.
2
Additional Information
Project data that has been edited offline can be transferred to an FH vision sensor. The following message appears when an online connection is established or the first time an editing
screen is opened.
If you select [OK], the settings data are transferred to the vision sensor. After the transfer completes, restart the vision sensor to reflect the settings data.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 21
2 Basic Operations
2-5-1
Switching Scenes
You can switch scenes by selecting the target scene in the scene list and then clicking the [Switch] button.
When scene switching is performed, the scene data editing screen is closed automatically if it is open in
the Edit Pane.
2-5-2
Managing Scenes
Right-clicking a target scene in the scene list displays the following menu.
Select the menu item for the operation you wish to perform.
Item
Copy
Paste
Delete
Description
Save to file
Copies the selected scene.
Pastes the copied scene.
Clears the selected scene.
When online, saves the selected scene as a scene data file to the RAMDisk or USB
memory of the sensor. When offline, saves it to the following folder on the PC.
Load from file
C:\Documents and Settings\<User name>\My Documents\OMRON FH
When online, loads a scene data file in the RAMDisk or USB memory of the sensor to
the selected scene. When offline, loads the scene data file in the following folder on the
PC.
C:\Documents and Settings\<User name>\My Documents\OMRON FH
2 - 22
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-5 Basic Operations of Scene Data
2-5-3
Entering Scene Information
The scene list displays the following information.
2
Description
Displays the scene name. (Maximum of 15 characters)
Displays the author name. (Maximum of 15 characters)
Displays the comment. (Maximum of 255 characters)
Each item in the list can be directly edited.
2-5-4
Searching for a Scene
You can search for a scene in the list by entering any scene name in the search box and then clicking
the search button (
2-5-5
). Clicking the search clear button (
) clears the search results.
Switching Scene Groups
Clicking the scene group editing button displays the scene group editing window.
You can switch scene groups by selecting the target scene group in the list and then clicking the
[Switch] button.
When scene switching is performed, the scene data editing screen is closed automatically if it is open in
the Edit Pane.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 23
2-5-3 Entering Scene Information
Item
Scene Name
Author
Comment
2 Basic Operations
2-5-6
Managing Scene Groups
Right-clicking a target scene group in the scene group list in the scene group editing window displays
the following menu.
Select the menu item for the operation you wish to perform.
Item
Save to file
Description
Copies the selected scene group.
Pastes the copied scene group.
Clears the selected scene group.
When online, saves the selected scene group as a file to the RAMDisk or USB memory
of the sensor. When offline, saves it to the following folder on the PC.
Load from file
C:\Documents and Settings\<User name>\My Documents\OMRON FH
When online, loads a scene data file in the RAMDisk or USB memory of the sensor to
the selected scene group. When offline, loads the scene data file in the following folder
on the PC.
Copy
Paste
Delete
C:\Documents and Settings\<User name>\My Documents\OMRON FH
2 - 24
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-5 Basic Operations of Scene Data
2-5-7
Entering Scene Group Information
The scene group list displays the following information.
Item
Scene group Name
Description
Displays the scene group name.
The current scene group name can be edited.
2
2-5-7 Entering Scene Group Information
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 25
2 Basic Operations
2-6
Basic Operations of Flow Editing
This section describes how to edit the flow.
Edit the flow in the scene data editing screen. For details on the scene data editing screen, refer to
Scene data editing screen on page 2-18.
You can open the scene data editing screen in the Edit pane by double-clicking scene data, or by
right-clicking it and selecting [Edit] from the menu.
Additional Information
Project data that has been edited offline can be transferred to an FH vision sensor. The following message appears when an online connection is established or the first time an editing
screen is opened.
If you select [OK], the settings data are transferred to the vision sensor. After the transfer completes, restart the vision sensor to reflect the settings data.
2 - 26
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
Adding a Processing Unit
When you wish to add a new processing unit to the flow, first select any processing unit from the Toolbox.
Then drag the selected processing unit to the place you wish to insert it in the flow list.
2-6 Basic Operations of Flow Editing
2-6-1
2
2-6-1 Adding a Processing Unit
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 27
2 Basic Operations
2-6-2
Managing Processing Units
Right-clicking a target processing unit in the flow list displays the following menu.
Select the menu item for the operation you wish to perform.
Item
Description
Edit*1
Opens the processing unit editing screen.
Rename
New folder
Copy
Paste
Delete
Changes the name of the processing unit.
Inserts a folder unit.
Copies the selected processing unit.
Pastes the copied processing unit.
Clears the selected processing unit.
Saves the settings data of the processing unit to a file.
When online, saves it to the RAMDisk or USB memory of the sensor. When offline,
saves it to the following folder on the PC.
Save to file
C:\Documents and Settings\<User name>\My Documents\OMRON FH
Loads the settings data of the processing unit from a file.
Load from file
When online, loads the file in the RAMDisk or USB memory of the sensor. When offline,
loads the file in the following folder on the PC.
C:\Documents and Settings\<User name>\My Documents\OMRON FH
*1. If the processing item is not supported in the edit operation, the following message appears.
"The ProcItem has not been supported."
Menu buttons
Button
Description
Copies the processing unit with the focus on it.
Pastes the copied processing unit.
Deletes the processing unit with the focus on it.
2 - 28
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-6 Basic Operations of Flow Editing
Display is hierarchical in the flow list when the following processing units are used.
• Folder unit
• Parallelize unit
• Parallelize task unit
<No folder unit>
2
2-6-2 Managing Processing Units
<Folder unit layer 1>
<Folder unit layer 2>
<Parallelize unit>
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 - 29
2 Basic Operations
2-6-3
Searching for a Processing Unit
You can search for a processing unit in the flow list by entering any processing unit name in the search
box and then clicking the search button (
results.
2 - 30
). Clicking the search clear button (
) clears the search
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-7
List of Functions Provided with the FH Tool
The following shows the functions provided with the FH tool and the usage conditions.
Classification
Item
Function
Project
management
Menu Item
Edit
Insert
Tools
Help
Edit
operations
Toolbar
Copy
Paste
Delete
Help
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
When
Offline
Editing
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
2 - 31
2
2-7-1 List of Functions Provided with the FH Tool
File
Close
Save
Save As
Save As New Number
Import
Export
Page Settings
Print
Exit
Copy
Paste
Delete
Controller
Vision Sensor
Displacement Sensor
Option
Help Contents
Online Registration
Keyboard Mapping Reference
About Sysmac Studio
When
Online
Editing
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
2-7 Function List
2-7-1
Function List
2 Basic Operations
Classification
Item
Function
Add | FH
Rename
Edit
Delete
Type
Restart
Online
Offline
Monitor window
Scene maintenance window
Save data
Line X
Rename
Save to file
Load from file
Edit
Scene data
Save to file
Load from file
Edit
System data
Save to file
Load from file
Communica- Edit
tion
Save to file
command
Load from file
customize
Tools
Save file
Edit
Calibration
Edit
Support Tool
User Data
Edit
Camera images
File images
* File images in the vision sensor
Online measurement
Logging images
File images
* File images in the PC
Device Group
Parameter
settings
Multiview
Tools
Multiview
Measurement
control
2 - 32
Edit Pane
When
Online
Editing
○
○
○
○
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
When
Offline
Editing
○
○
○
○
○
○
x
○
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
x
○
x
○
x
x
○
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
2 Basic Operations
2-7-2
Comparison with FH Series Unit Functions
The following table shows the main differences between the functions provided with an FH series
device and the FH tool.
Project
management
Simulation
Data management for a single FH vision sensor
Data management for all devices
Screen customization and screen layout control
Creating and displaying dedicated dialog boxes
Communication command customize
File save
Calibration Support Tool
NG analyzer
User data tool
Security settings
Downloading and uploading setting values
Image file saving
Registered image management tool
Flow viewer
Reference position batch conversion tool
Scene group data conversion tool
Single simulation
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Sysmac
Studio
○
○
x
x
○
○
○
x
○
x
○
x
x
x
x
x
○
FH
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
2 - 33
2
2-7-2 Comparison with FH Series Unit Functions
Tools
Item
2-7 Function List
Classification
2 Basic Operations
2 - 34
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Connecting with a Vision Sensor
3
This section describes how to establish a connection with a vision sensor.
3-1 Adding FH Series Vision Sensor on the Network to a Project . . . . . . . . . . 3-3
3-2 Establishing an Online Connection with a Vision Sensor . . . . . . . . . . . . . 3-4
3-2-1
3-2-2
Establishing an Online Connection from the Sensor Connection Screen . . . . . 3-4
Establishing an Online Connection from the Multiview Explorer . . . . . . . . . . . . 3-6
3-3 Transferring Project Data to a Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-4 Ending a Connection with a Vision Sensor . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3-4-1
3-4-2
Ending a Connection in the Sensor Connection Screen . . . . . . . . . . . . . . . . . . 3-8
Ending a Connection in the Multiview Explorer . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3-1
3 Connecting with a Vision Sensor
To establish an online connection with FH vision sensor, configure settings and make adjustments, connect directly by Ethernet. You can also connect via a hub or router.
It is not possible to set and adjust FH vision sensor via NJ series controller.
Ethernet
3-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3 Connecting with a Vision Sensor
Adding FH Series Vision Sensor on
the Network to a Project
When creating a new project or adding FH vision sensor to a project, select FH vision sensor on the
network.
When connecting to the FH vision sensor, right-click [Device Group] in the Multiview Explorer and then
select [Add | FH].
3-1 Adding FH Series Vision Sensor on the Network to a
Project
3-1
3
The following sensor selection screen appears.
When establishing an online connection, click [Search for sensors] and then click the [Search] button.
The found sensors are displayed in a list. Select the sensor you wish to connect to and then click the
[OK] button.
If you know the IP address of the sensor you wish to connect to beforehand or will connect to a sensor
via a router, select the [Specify the IP address.] check box and then enter the IP address in [IP
address]. After input is complete, click the [OK] button.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3-3
3 Connecting with a Vision Sensor
3-2
Establishing an Online Connection
with a Vision Sensor
Connect with FH vision sensor on the network.
Precautions for Correct Use
• When you connect vision sensors to Sysmac Studio by the network, set the same network
addresses for all the vision sensors and computer where Sysmac Studio is running.
e.g., when the Ethernet settings set for the vision sensors are as follows, the network
addresses of the vision sensors and the computer are "[email protected]"
• IP address: 10.5.5.100
• Subnet mask: 255.255.255.0
• If you plan to control the vision sensor from Sysmac Studio over the network, you will need to
have the Remote Operation option for the Communication module for the FH sensor controller set to ON (initial setting).
For details on how to configure the settings, refer to the Vision System FH/FZ5 Series User's
Manual (Cat. No. Z340).
3-2-1
Establishing an Online Connection from the Sensor Connection
Screen
You can open the sensor connection screen in the Edit Pane by double-clicking the type name of the
FH vision sensor in the Multiview Explorer or by right-clicking it and selecting [Edit] from the menu.
<Multiview Explorer>
3-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3 Connecting with a Vision Sensor
3-2 Establishing an Online Connection with a Vision
Sensor
<Sensor connection screen>
3
You can also directly enter an IP address in the IP address field.
If you wish to connect with an FH vision sensor via a router, directly enter the IP address and then click
the [Connect] button.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3-5
3-2-1 Establishing an Online Connection from the Sensor Connection Screen
Click the [Search for sensors] button of [Online] - [Sensor connection] to display a list of the IP
addresses of the FH vision sensors on the same network. Select the FH vision sensor you wish to connect to and then click the [Connect] button.
3 Connecting with a Vision Sensor
3-2-2
Establishing an Online Connection from the Multiview Explorer
If the FH vision sensor to be connected has already been set, you can establish an online connection
with it by right-clicking the type name of the FH vision sensor in the Multiview Explorer and then selecting [Online].
For details on setting the FH vision sensor to be connected, refer to 3-2-1 Establishing an Online Connection from the Sensor Connection Screen on page 3-4.
If the FH vision sensor that has already been set cannot be found, the automatically detected FH vision
sensors are displayed in a list. Select the FH vision sensor you wish to connect to.
3-6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3 Connecting with a Vision Sensor
Transferring Project Data to a Sensor
Project data that has been edited offline can be transferred to FH vision sensor. The following message
appears when an online connection is established or the first time an editing screen is opened.
If you select [OK] to transfer the project data, restart the sensor to reflect the data transferred to the
sensor.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3-7
3-3 Transferring Project Data to a Sensor
3-3
3
3 Connecting with a Vision Sensor
3-4
Ending a Connection with a Vision
Sensor
End the connection with a sensor currently connected with an online connection and switch to the
offline state.
3-4-1
Ending a Connection in the Sensor Connection Screen
Open the sensor connection screen and then click the [Disconnect] button of [Online] - [Sensor connection].
The following message is displayed when returning to the offline state. Select whether to transfer the
sensor settings data to the project.
If [OK] is selected, the sensor settings data is reflected in the project.
If [Cancel] is selected, the sensor settings data is not reflected in the project. The editing state returns
to the state before the online connection was established.
3-8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3 Connecting with a Vision Sensor
Ending a Connection in the Multiview Explorer
Right-click the type name in the Multiview Explorer and select [Offline] from the menu.
Just as described in "Ending a Connection in the Sensor Connection Screen," the connection state
switches to offline after you select whether to transfer the sensor settings data to the project.
3-4 Ending a Connection with a Vision Sensor
3-4-2
3
3-4-2 Ending a Connection in the Multiview Explorer
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
3-9
3 Connecting with a Vision Sensor
3 - 10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Configuring Measurement
Settings
On the FH vision sensor, processing items can be combined to configure measurement
details. This section provides an overview of the processing units and describes how to
edit a processing unit.
4-1 Overview of Processing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4-1-1
4-1-2
4-1-3
4-1-4
4-1-5
4-1-6
4-1-7
Input Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compensate Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Support Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Branch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
4-2
4-2
4-3
4-3
4-3
4-3
4-2 Editing a Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4-2-1
4-2-2
4-2-3
4-2-4
4-2-5
4-2-6
4-2-7
4-2-8
Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Editing an Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Color Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Binary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Detection Point/Reference Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Image Control Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4-1
4
4 Configuring Measurement Settings
4-1
Overview of Processing Units
This section provides an overview of the processing units that can be edited in the FH tools.
For details on each of the processing units, refer to the Vision System FH/FZ5 Series Processing Item
Function Reference Manual (Cat. No. Z341.)
4-1-1
Input Image
This is a processing unit for loading images from a camera.
The main setting items are as follows.
Group
Camera setting
Screen adjust
White balance
Calibration
HDR setting
Bright adjust setting
4-1-2
Item
Sets the camera shooting conditions.
Sets the conditions related to the lighting and lens.
Sets the white balance in images loaded from the camera to correct its color
and to make the white parts appear as white.
Configures the settings for converting measurement results to the actual
dimensions.
Sets the method for combining images in order to obtain it with a wide
dynamic range.
Sets how much the brightness of loaded images to be adjusted.
Measurement
This is a processing unit for inspection and measurement.
The main setting items are as follows.
Group
Model
Region setting
Detection point
Ref. setting
Measurement condition
Judgment condition
Output conditions
Color
4-1-3
Item
Allows you to register the parts you wish to inspect as models.
Sets the range for searching a model and the range for calculating the
amount of a certain feature.
Sets which parts of a model you wish to detect as the coordinates during
measurement.
Changes the measurement values that will be the reference registered during model registration and region setting.
Sets the condition for performing measurement.
Sets the judgment condition for measurement values.
Sets the reflection condition for the coordinates or overall judgment output as
measurement results.
Sets the color information used for measurement.
Compensate Image
This is a processing unit for correcting images.
The main setting items are as follows.
Group
Filter setting
Region setting
Output image
4-2
Item
Sets the filter conditions for image correction.
Sets the region for performing correction.
Selects the image to output.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 Configuring Measurement Settings
4-1-4
Support Measurement
This is a processing unit for providing support for calculation processing, data acquisition and browsing,
and other processing.
The main setting items are as follows.
Item
Sets the condition for performing measurement.
Judgment condition
Sets the judgment condition for measurement values.
Sets the reflection condition for the coordinates or overall judgment output as
measurement results.
Output parameter
*1. The item names differ for each processing unit.
4-1-5
Branch
This is the processing unit for performing branching processing.
The main setting items are as follows.
Setting
Output conditions
4-1-6
4
Item
Sets the condition for performing branching.
Sets the communication function and timeout function for performing flow
control by communication.
Sets the reflection condition for the overall judgment.
Output Result
This is the processing unit for outputting measurement results to an external device.
The main setting items are as follows.
Group
Setting
Output format
Output conditions
4-1-7
Item
Sets the content to output.
Sets the format of the data to output.
Sets the reflection condition for the overall judgment.
Display Result
This is the processing unit for displaying any text, figure, or image on the screen displaying the measurement results.
The main setting items are as follows.
Group
Item
Setting*1
Sets the content or condition to display.
Output conditions
Sets the reflection condition for the overall judgment.
*1. The item names differ for each processing unit.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4-3
4-1-4 Support Measurement
Group
Branch setting
4-1 Overview of Processing Units
Group
Setting*1
4 Configuring Measurement Settings
4-2
Editing a Processing Unit
Right-click any processing unit in the flow list and then select [Edit] from the menu.
The editing screen of the selected processing unit appears.
The editing screens of processing units are categorized into the following two types.
<Editing Screen with Image Display>
<Editing Screen without Image Display>
Each setting menu can be opened and closed on a group basis. In an editing screen with image display, an image or graphic information is displayed in accordance with the open menu.
Clicking the [OK] button confirms the changes and closes the editing screen of the processing unit.
Clicking the [Cancel] button discards the changes and closes the editing screen of the processing unit.
The basic editing operations that can be performed with this tool are described below.
4-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 Configuring Measurement Settings
4-2-1
Parameter Settings
The following table lists the basic user interface components used for editing parameters.
UI
Numerical value input
area
(With slider)
After clicking
Before clicking
After clicking
Description
Allows you to enter numerical data.
Entered data is treated as a double type value, but
is displayed up to 4 digits after the decimal point.
Allows you to enter numerical data.
Entered data is treated as a double type value, but
is displayed up to 4 digits after the decimal point.
Clicking the button beside the numerical value input
box displays a slider. Parameter values can be
adjusted with the slider.
Numerical value upper
limit and lower limit
input area
(With slider)
Allows you to enter numerical data for the upper and
lower limits.
Entered data is treated as a double type value, but
is display is up to 4 digits after the decimal point.
Before clicking
After clicking
Before clicking
Numerical value upper
limit and lower limit
input area
(With slider)
(With measurement
value display)
Expression
It is not possible to set a lower limit value that is
greater than the upper limit value.
This is the numerical value upper limit and lower
limit input area with the addition of measurement
value display.
The bar at the place of the measurement value of
the slider is green when the value is OK and red
when it is NG.
Allows you to enter an expression.
When input is complete, a validity check is performed for the expression.
After clicking
Clicking the button beside the text input box displays the calculation parameter input area. Any
parameter can be inserted.
Text input area
Allows you to enter any text.
The following characters cannot be entered.
• !
Unselected
Radio button
• Tab
Selects one item from multiple selection items.
Check box
Enables or disable an item.
Selected
Unchecked
Checked
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4-5
4
4-2-1 Parameter Settings
Clicking the button beside the numerical value input
box displays a slider. Parameter values can be
adjusted with the slider.
4-2 Editing a Processing Unit
Before clicking
Item
Numerical value input
area
4 Configuring Measurement Settings
UI
Item
Combo box
Before clicking
Description
Selects one item from multiple selection items.
After clicking
4-2-2
Editing an Area
You can edit a model area or measurement area.
Click the area editing button to display the area editing menu.
→
Six area editing functions are provided.
Rectangle
This function draws a rectangle. You can change the size of the rectangle by dragging the four corners.
The rectangle can be moved by clicking and then dragging the inside of the rectangle.
4-6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 Configuring Measurement Settings
Wide line
2)
1)
1)
This function draws a wide line. You can change the size or direction by dragging the following vertices.
• Vertex (1)
4-2 Editing a Processing Unit
2)
You can change the length or direction of the line by changing the start point or end point.
• Vertex (2)
4
These allow you to change the width of the line.
4-2-2 Editing an Area
The line can be moved by clicking and then dragging the inside of the area.
Ellipse
3)
2)
2)
1)
3)
This function draws a circle or ellipse. You can change the size by dragging the following vertices.
• Vertex (1)
These allow you to change the overall size while maintaining the XY ratio.
• Vertex (2)
These allow you change the size in the X direction.
• Vertex (3)
These allow you change the size in the Y direction.
The eclipse can be moved by clicking and then dragging the inside of the area.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4-7
4 Configuring Measurement Settings
Circumference
Vertex (1)
Vertex (2)
This function draws a circumference. You can change the size by dragging the following vertices.
• Vertex (1)
These change the radius of the inner circle.
• Vertex (2)
These change the size of the circle while maintaining the difference in the diameters of the inner and
outer circles.
The circumference can be moved by clicking and then dragging the inside of the area.
Wide arc
2)
2)
1)
3)
1)
This function draws a wide arc. You can change the start point, end point, width, and position by dragging the following vertices.
• Vertex (1)
These allow you to change the width.
• Vertex (2)
These allow you to change the start point, end point, and radius.
• Vertex (3)
This allows you to move the center position while keeping the start point and end point positions
fixed.
The arc can be moved by clicking and then dragging the inside of the area.
4-8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 Configuring Measurement Settings
Polygon
4-2 Editing a Processing Unit
This function draws a polygon. Up to 10 vertices can be added.
Clicking any position on a side creates a new vertex.
You can change the position of a vertex by dragging it.
The polygon can be moved by clicking and then dragging the inside of the area.
Color Extraction
4-2-3 Color Extraction
4-2-3
4
You can specify up to eight colors.
Also, when the Automatic check box is selected, enclosing any part in a displayed image automatically
extracts the color of that part.
The color range can be specified by specifying the hue, saturation, and brightness.
The specifications are the same as for the user interface of the FH vision sensor.
For details, refer to the Vision System FH/FZ5 Series Processing Item Function Reference Manual
(Cat. No. Z341.)
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4-9
4 Configuring Measurement Settings
4-2-4
Color
You can specify any color.
The color can be specified by specifying the hue, saturation, and brightness.
The specifications are the same as for the user interface of the FH vision sensor.
For details, refer to the Vision System FH/FZ5 Series Processing Item Function Reference Manual
(Cat. No. Z341.)
4-2-5
Binary
You can specify the range of binarization levels.
If you select the [Binary Reverse] check box, binarization is performed for outside of the range between
the upper and lower limits.
4 - 10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 Configuring Measurement Settings
4-2-6
Detection Point/Reference Point
4-2 Editing a Processing Unit
The detection point and reference point can be set with the numerical value input boxes.
Clicking any place in the displayed image reflects that coordinate value as the setting value.
4-2-7
List
4
4-2-8
Image Control Area
File selection section
This allows you to select the image to display. Refer to File selection section on page 2-16.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
4 - 11
4-2-6 Detection Point/Reference Point
Selecting an item in the list displays the information for the selected item below the list. Each of the
information items displayed below the list can be edited.
4 Configuring Measurement Settings
Image control section
This allows you to control the measurement of the image. Refer to Image control section on page 2-16.
Image size control section
This allows you to enlarge or reduce the displayed image.
The place where the image is displayed in the left zoom area is enclosed in a rectangle.
You can move the display place by moving this rectangle.
Button
Description
Enlarges the image. Doubles the size of displayed image. (Upper limit: 1600%)
Reduces the image. Halves the size of displayed Image. (Lower limit: 1%)
Makes the image to fit the display frame.
The zoom ratio can be specified by directly entering a numerical value or by moving the
slider.
4 - 12
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Designing Exchange with External
Devices
This section describes how to establish a connection with an external device.
5-1 Setting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
5-1
5 Designing Exchange with External Devices
The FH vision sensor has the following interfaces.
• Parallel I/O
• RS-232C/422
• Ethernet
• EtherCAT
Each interface supports various communication protocols.
You can configure their communication settings in the system settings of the FH tools.
Configure the communication settings for each line when in the multiple multi-line random-trigger
modes. However, some data is settings data that is common to the lines.
Group
Item
Parallel I/O
―
Common to lines
RS-232C/422
Ethernet
EtherNet/IP
EtherCAT
Attribute
Common to lines
―
Address settings
Input/output settings
Common to lines
Individual to each line
Individual to each line
* Some parameters are common to lines
Individual to each line
If the communication settings are changed, the FH vision sensor needs to be restarted.
If a parameter that requires a restart is edited, "
Explorer. If "
" is displayed for the sensor type in the Multiview
" is displayed, save the settings and then restart the FH vision sensor.
For details on restarting, refer to 2-4-4 Multiview Explorer on page 2-10.
5-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
5 Designing Exchange with External Devices
5-1
Setting Procedure
You can open the system settings screen by double-clicking [System data] in the Multiview Explorer or
by right-clicking it and selecting [Edit] from the menu.
For details on the settings, refer to the Vision System FH/FZ5 Series User's Manual (Cat. No. Z340.)
5-1 Setting Procedure
In the system settings screen, you can click any of the following buttons to configure the corresponding
settings.
5
Button
Setting Item
Description
Parallel I/O
Sets the Parallel I/O settings.
RS-232C/422
Sets the RS-232C/422 settings.
Ethernet
Sets the settings related to Ethernet.
EtherNet/IP
Sets the settings related to EtherNet/IP.
EtherCAT
Sets the settings related to EtherCAT.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
5-3
5 Designing Exchange with External Devices
Precautions for Correct Use
• A restart is required after configuring the Ethernet, EtherNet/IP, and EtherCAT settings.
• When multi-line random-trigger mode is selected, the communication settings needs to be
configured for each line.
However, the RS-232C/422 settings are common between the lines.
For the other communication settings, individually configure the settings in the system settings for each line.
5-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Online Debugging
This section describes how to perform online debugging of the FH sensor controller.
6-1 Performing Test Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6-1-1
6-1-2
6-1-3
Measuring Camera Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Measuring File Images in the RAMDisk or USB Memory of
the Vision Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Measuring Logging Images in the Vision Sensor Memory . . . . . . . . . . . . . . . . 6-3
6-2 Checking Measurement Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
6-2-1
6-2-2
6-2-3
Checking Detailed Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Changing the Image Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Checking Multiple Measurement Images at the Same Time . . . . . . . . . . . . . . 6-6
6-3 Checking Result Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6-4 Saving Measurement Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6-5 Saving Settings Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6-1
6
6 Online Debugging
6-1
Performing Test Measurement
You can perform test measurement with the FH tools.
Select from the following three test measurement target images when connected with an online connection.
Target Image
Camera image
Measurement Type
Single measurement
Continuous measurement
Single measurement
File image
Continuous measurement
Single measurement
Logging image
Continuous measurement
6-1-1
Description
Measures a camera image.
Continuously measures camera images.
Allows you to select and measure a file image in the RAMDisk
or USB memory of the FH vision sensor.
Continuously measures file images in the RAMDisk or USB
memory of the FH vision sensor. Measurement ends when
measurement of the images within the same folder finishes.
Allows you to select and measure a logging image in the FH
vision sensor memory.
Continuously measures logging images in the FH vision sensor memory. Measurement ends when measurement of all logging images finishes.
Measuring Camera Images
To select a camera image, first click the camera image button (
) in the file selection section.
Then select a camera image and click the [Measure] button.
[Measure] is provided in the following editing screens.
• Scene maintenance window
• Scene editing screen
• Processing unit editing screen
<Scene maintenance window>
<Scene editing screen>
6-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6 Online Debugging
<Processing unit editing screen>
To start continuous measurement, click the continuous measurement button (
).
If you wish to stop continuous measurement, click the continuous measurement stop button (
).
The settings data cannot be edited during continuous measurement.
6-1 Performing Test Measurement
6-1-2
Measuring File Images in the RAMDisk or USB Memory of the
Vision Sensor
Select the measurement target file and click the [Measure] button.
Select the file as described below.
1
2
3
Click the [File] button.
Click the file selection button (
) and then select the target file.
Click the [Measure] button.
6
).
If you wish to stop continuous measurement, click the continuous measurement stop button (
).
The settings data cannot be edited during continuous measurement.
6-1-3
Measuring Logging Images in the Vision Sensor Memory
Select the measurement target logging image and click the [Measure] button.
Select the file as described below.
1
2
Click the [Logging image] button.
Click the [Measure] button.
If you wish to change the measurement target logging image, click the button for measuring the previous image (
) or click the button for measuring the next image (
).
To start continuous measurement, click the continuous measurement button (
).
If you wish to stop continuous measurement, click the continuous measurement stop button (
).
The settings data cannot be edited during continuous measurement.
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6-3
6-1-2 Measuring File Images in the RAMDisk or USB Memory of the Vision Sensor
To start continuous measurement, click the continuous measurement button (
6 Online Debugging
6-2
Checking Measurement Results
You can check the measurement results in each editing screen.
On the displayed image, the measurement results of the selected processing unit are displayed as a
graphic.
6-2-1
Checking Detailed Results
Scene maintenance window, monitor window, and scene data editing screen
Open the [Flow] item and [Detail result] item and click the [Measure] button.
If you select any of the processing units in the list of the [Flow] item, the measurement result of each
item that is a judgment result of that processing unit will be displayed in the [Detail result] item.
<Scene maintenance screen>
<Monitor window>
6-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6 Online Debugging
<Scene data editing screen>
6-2 Checking Measurement Results
Processing unit editing screen
Open the [Judgment condition] item and click the [Measure] button.
The measurement result of each item that is a judgment result of the processing unit is displayed
6
6-2-1 Checking Detailed Results
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6-5
6 Online Debugging
6-2-2
Changing the Image Display Settings
You can change the setting for displaying images in the scene maintenance window and monitor window.
Open the [Image display settings] item and change each items.
For details on the image display settings, refer to Image display settings on page 2-15.
Item
Image layout
Image mode
Positions
Sub image
Description
Selects the number of images to display.
Selection items: 1Form, 2Form, and 4Form
Selects the image mode for the image with the focus on it.
Selection items: Through, Freeze, and NG image
Selects position list display for the image with the focus on it.
Selection items: OFF and ON
Selects the sub image number for the image with the focus on it.
Selection items: Image0, Image1,..., image31
You can switch the result display content of the processing unit by changing the sub image number.
For details, refer to the content of each processing unit in the Vision System FH/FZ5 Series Processing
Item Function Reference Manual (Cat. No. Z341.)
6-2-3
Checking Multiple Measurement Images at the Same Time
You can display multiple images by opening the [Image display settings] item and changing [Image layout].
For details on the image display settings, refer to Image display settings on page 2-15.
<2Form display>
6-6
<4Form display>
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6 Online Debugging
6-3
Checking Result Output
Normally, output to an external device is performed when the monitor window is open, but it is not performed while scene data is being edited in the following editing screens.
• Scene maintenance window
• Scene data editing screen
• Processing unit editing screen
• Editing screen of each tool
If you wish to output the measurement results in those screens, select the following check box in the
adjustment screen.
• [Test measurement settings] - [Output]
6-3 Checking Result Output
6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6-7
6 Online Debugging
6-4
Saving Measurement Results
If you wish to save measurement results or images, use the logging related processing units.
• Image logging
• Image conversion logging
• Data logging
These processing units can be used to output images and measurement results to the RAMDisk/USB
memory of the FH vision sensor or the FH vision sensor memory.
For details on the processing units, refer to the Vision System FH/FZ5 Series Processing Item Function
Reference Manual (Cat. No. Z341.)
To acquire the files output to the RAMDisk or USB memory of the FH vision sensor, use the file management tool
For details, refer to 8-3 Using the File Save Tool on page 8-4.
6-8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6 Online Debugging
6-5
Saving Settings Data
After adjusting the settings data, you need to save the settings data to the flash memory of the FH
vision sensor. There are the following two ways to save the settings data.
(1) Right-click [Configuration and Setup] - [Device Group] - [FH-XXXX] - [Line X] in the Multiview Explorer and then click [Save data].
6-5 Saving Settings Data
(2) Click the [Data save] button in the scene maintenance window.
6
The settings data can also be saved and managed as files.
• Scene data basis (Refer to 2-5-2 Managing Scenes on page 2-22)
• Scene group basis (Refer to 2-5-6 Managing Scene Groups on page 2-24)
• Processing unit basis (Refer to 2-6-2 Managing Processing Units on page 2-28)
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
6-9
6 Online Debugging
6 - 10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Offline Debugging
This section describes offline debugging techniques for the FH sensor controller.
7-1 Performing Offline Simulation of Sensor Measurement Operation . . . . . 7-2
7
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
7-1
7 Offline Debugging
7-1
Performing Offline Simulation of
Sensor Measurement Operation
Even when offline, simulation of the measurement operation can be performed using file images on the
PC.
Selection and measurement of file image can be performed in the following editing screens.
• Scene maintenance window
• Scene editing screen
• Processing unit editing screen
Select the file as described below.
1
2
3
Click the [File] button.
Click the file selection button (
) and then select the target file.
Click the [Measure] button.
If you click the continuous measurement button ( ), continuous measurement of the images in the
same folder is performed. Measurement ends when measurement of all the files finishes.
If you wish to stop continuous measurement part way through the process, click the continuous measurement stop button (
).
The [Measure] button is provided in the monitor window, scene maintenance window, and processing
unit editing screen.
For details, refer to 6-1-1 Measuring Camera Images on page 6-2.
Additional Information
The images measured with the sensor can be saved as logging image files.
Refer to 8-3-3 Saving a Logging Image as a File on page 8-6.
7-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Other Useful Functions
This section provides a list of useful tools that can be used in the configuration and
operation of the FH series vision sensors.
8-1 Using the Command Customize Setting Tool . . . . . . . . . . . . . . . . . . . . . . . 8-2
8-2 Using the Calibration Support Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8-3 Using the File Save Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8-3-1
8-3-2
8-3-3
Opening the File Save Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Copying a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Saving a Logging Image as a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
8-4 Using the User Data Setting Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8-5 Changing the System Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
8-6 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8-1
8 Other Useful Functions
8-1
Using the Command Customize
Setting Tool
This tools allows you to edit custom commands.
It is the same as the [Tools] - [Communication Command Customize] function provided with the FH
vision sensor.
For details, refer to the Vision System FH/FZ5 Series User's Manual (Cat. No. Z340.)
8-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8 Other Useful Functions
8-2
Using the Calibration Support Tool
A calibration support tool is available.
It is the same as the [Tools] - [Calibration Support Tool] function provided with the FH vision sensor.
For details, refer to the Vision System FH/FZ5 Series User's Manual (Cat. No. Z340.)
8-2 Using the Calibration Support Tool
8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8-3
8 Other Useful Functions
8-3
Using the File Save Tool
The file save tool allows you to copy and transfer files in the RAMDisk or USB memory of the FH vision
sensor. It also allows you to output logging image files in the FH vision sensor memory.
8-3-1
Opening the File Save Tool
To open the File Save Tool, select [Tools] - [Save file] in the Multiview Explorer and then either double-click [Save file] to pull up the Save screen or right-click and select [Edit] from the pop-up menu that
appears.
The file management tool screen appears in the Edit pane.
8-3-2
Copying a File
You can copy a file in the RAMDisk or USB memory of the FH vision sensor and then save it under a
different name or transfer it to the PC.
8-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8 Other Useful Functions
1
2
Select [File] for [Target data].
Select a file.
You can select data on a folder basis or on a file basis.
If you select an individual folder, you can narrow down the files by type.
The following file types can be selected to narrow down the data.
• All files
• Logging images (*.ifz, *.byr)
• Bitmap (*.bmp)
• CSV (*.csv)
• Scene data (*.scn)
• Scene group data (*.sgp)
• System data (*.ini)
• System settings + Scene group 0 data (*.bkd)
• Operation log (*.log)
3
Select the save destination folder.
To save the file by copying it to the RAMDisk or USB memory of the FH vision sensor, select
[Sensor].
To save the file to the PC, select [PC].
8-3 Using the File Save Tool
When saving to the PC, you can save to the following folder.
C:\Documents and Settings\<User name>\My Documents\OMRON FH
If you wish to delete the original file after saving, select the [Delete original data after save]
check box.
4
Save the file.
Click the [Save file] button to save the file.
The selected file is copied to the specified folder.
8
8-3-2 Copying a File
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8-5
8 Other Useful Functions
8-3-3
Saving a Logging Image as a File
You can save a logging image in the FH vision sensor memory as a file.
1
2
Select [Logging image] for [Target data].
Select the save target.
Select whether to save all logging images or a particular logging image.
3
Select the save destination folder.
To save the file to the RAMDisk or USB memory of the FH vision sensor, select [Sensor].
To save the file to the PC, select [PC].
When saving to the PC, you can save to the following folder.
C:\Documents and Settings\<User name>\My Documents\OMRON FH
4
Save the file.
Click the [Save file] button to save the file.
The selected logging file is output to the specified folder.
8-6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8 Other Useful Functions
8-4
Using the User Data Setting Tool
This tool allows you to edit user data.
It is the same as the [Tools] - [User Data] function provided with the FH vision sensor.
For details, refer to the Vision System FH/FZ5 Series User's Manual (Cat. No. Z340.)
8-4 Using the User Data Setting Tool
8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8-7
8 Other Useful Functions
8-5
Changing the System Environment
You can change the system data for the FH vision sensor in the system data editing screen.
Display the system data editing screen in the Edit Pane by double-clicking [System] in the Multiview
Explorer or by right-clicking it and selecting [Edit] from the menu.
System data is classified into the groups shown in Table 1.
Clicking a group icon displays the editing items for the corresponding group.
System data includes parameters that require a restart to reflect the settings.
If a parameter that requires a restart is edited, "
Explorer. If "
" is displayed for the sensor type in the Multiview
" is displayed, save the settings and then restart the FH vision sensor.
For details on restarting, refer to 2-4-4 Multiview Explorer on page 2-10.
For details on each setting item, refer to the Vision System FH/FZ5 Series User's Manual (Cat. No.
Z340.)
8-8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8 Other Useful Functions
Table 1
Button
Item
Sub Item
Camera connection
Camera settings
Inter-camera setting
Output signal settings
Startup settings
Fan control setting
STEP setting
Controller settings
Network drive settings
Measurement setting
Image logging settings
Data log settings
Operation log settings
Parallel I/O settings
RS-232C/422 settings
Settings
PLC link settings
Address settings
8-5 Changing the System Environment
Ethernet settings
Settings
Input/Output settings
PLC link settings
EtherNet/IP settings
EtherNet/IP communication
EtherCAT settings
EtherCAT communication
Encoder settings
Encoder settings
8
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
8-9
8 Other Useful Functions
8-6
Help
You can display the FH tool manual.
Display the sensor connection screen in the Edit Pane by double-clicking the type in the Multiview
Explorer or by right-clicking it and selecting [Edit] from the menu.
Click [Sensor Information] - [Help] to display the manual for the FH series vision sensors.
8 - 10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Limitations
This section provides a list of the limitations associated with the use of the FH sensor
controller with the FH tools.
9-1 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
9
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
9-1
9 Limitations
9-1
Limitations
The FH tools have the following limitations.
Condition
Registration of multiple FH
series vision sensors to a
project
Editing of processing units
Limitation
Only one FH vision sensor can be registered to one project.
Limitations apply to editing processing units in Sysmac Studio. Refer to the following table.
List of the processing units supported in Sysmac Studio
Processing Unit
Camera Image Input
Camera Image Input FH
Camera Image Input HDR
Camera Image Input HDR Lite
Camera Switching
Measurement Image Switching
Position Compensation
Filtering
Background Suppression
Brightness Correct Filter
Advanced Filter
Image Subtraction
Color Gray Filter
Extract Color Filter
Anti Color Shading
Stripes Removal Filter II
Polar Transformation
Trapezoidal Correction
Panorama
Machine Simulator
Search
Flexible Search
Sensitive Search
EC Circle Search
ECM Search
Ec Corner
Ec Cross
Shape Search II
Shape Search III
Classification
Edge Position
Edge Pitch
Scan Edge Position
Scan Edge Width
Circular Scan Edge Position
Circular Scan Edge Width
Intersection
Gravity and Area
9-2
○: Supported, x: Not supported
Registration
Editing
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
x
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
x
○
○
○
○
○
○
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
x
○
○
○
x
○
○
○
x
○
○
○
x
○
○
○
○
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
9 Limitations
Processing Unit
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
9-3
9-1 Limitations
Labeling
Label Data
Color Data
Defect
Precise Defect
Fine Matching
2DCode
Barcode
Character Inspection
Model Dictionary
Date Verification
Circle Angle
Glue Bead Inspection
Calculation
Macro Calculation
Circle Regression
Line Regression
Movement Single Position
Movement Multi Points
Convert Position Data
Position Data Calculation
Precise Calibration
Vision Master Calibration
PLC Master Calibration
Reference Calib Data
Camera Calibration
Get Unit Data
Get Unit Figure
Set Unit Data
Set Unit Figure
Detection Point
Image Logging
Image Conversion Logging
Data Logging
Trend Monitor
Statistics
User Data
Data Save
Robot Data
Stage Data
Iris
Focus
Macro
Wait
Elapsed Time
Parallelize
Parallelize Task
Conditional Branch
DI Branch
End
Selective Branch
Control Flow Normal
○: Supported, x: Not supported
Registration
Editing
○
○
○
○
○
x
○
x
○
x
○
x
○
x
○
x
○
x
○
x
○
x
○
x
○
x
○
○
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
x
○
x
○
x
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
9
9 Limitations
Processing Unit
Control Flow PLC Link
Control Flow Parallel
Control Flow Fieldbus
Parallel Judgment Output
Data Output
Parallel Data Output
Fieldbus Data Output
Result Display
Display Image File
Display Last NG Image
9-4
○: Supported, x: Not supported
Registration
Editing
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
10
Troubleshooting
10-1 Troubleshooting for the EtherCAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
10-2 Sysmac Error Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
10 - 1
10 Troubleshooting
10-1 Troubleshooting for the EtherCAT
For details on how to perform troubleshooting for the EtherCAT, refer to the Vision System FH/FZ5
Series User's Manual for Communications Settings (Cat. No. Z342.)
10 - 2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
10 Troubleshooting
For details on Sysmac error statuses, refer to the Vision System FH/FZ5 Series User's Manual for
Communications Settings (Cat. No. Z342.)
10-2 Sysmac Error Status
10-2 Sysmac Error Status
10
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
10 - 3
10 Troubleshooting
10 - 4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
A
Appendices
A-1 Sysmac Device Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A-1-1 Sysmac Error Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A-1-2 Saving the Node Address Setting . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
A-1-3 Serial Number Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
A-1-4 Compliance with ESI Specification (ETG.2000 S (R) V1.0.1) . . . . . A-4
A-1-5 SII Data Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
A-1
Appendices
A-1 Sysmac Device Features
The control device product designed according to standardized communications and user interface
specifications for OMRON control devices are called a Sysmac Device.
And the features available with such a Device is called Sysmac Device Features.
A-1-1
Sysmac Error Status
Because, in Sysmac Devices, errors that may occur in slaves are systematized, you can check the
causes and remedies for errors with a common procedure.
The status of an error can be monitored in the Sysmac Error Status (2002-01 hex). To display the error
status detected by the FH series Vision Sensor in Sysmac Studio, the Sysmac Error Status (2002-01
hex) must be mapped to the PDO. Sysmac Studio, by default, uses the 512th transmit PDO Mapping
assignment to map the Sysmac Error Status (2002-01 hex) automatically to the PDO.
Additional Information
• For the Sysmac Error status (2002-01 hex), refer to the Vision System FH/FZ5 Series User's
Manual for Communications Settings (Cat. No. Z342).
• For errors displayed in Sysmac Studio, refer to the NJ-series Troubleshooting Manual (Cat.
No. W503).
A-2
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Appendices
Saving the Node Address Setting
When the node address switch setting is “00” (Software Setup mode), the node address value you set
in Sysmac Studio is enabled. If the node address switches are set to any other value, the value that is
set on the switches is used as the node address.
In the Software Setup mode, in Sysmac Studio, execute [Write Slave Node Address] on the [EtherCAT
Edit] screen to save the slave node address setting in the nonvolatile memory of the FH series Vision
Sensor.
Software Setting
The set value saved as Slave Information Interface (SII) information in the nonvolatile memory of the
slave is the node address.
(5)
EtherCAT
Slave Controller
Nonvolatile
memory
SII
(2)
Register : 0010h
Register : 0012h
(3)
(1) Node Address
Switch
EtherCAT Slave
(1) The Node Address Switch is set to "00" at
power OFF.
(2) Write a node address set value to Slave SII
from the master.
(3) The value of the node address setting is applied
to Register: 0012 hex by the software, when the
slave power is ON.
(4) EtherCAT master reads the set value of
Register: 0012 hex.
(5) EtherCAT master writes the value of 0012 hex
address to 0010 hex address as the node
address value.
Node Address Switch Setting
The value set on the node address switches is the node address.
EtherCAT master
(3)
(4)
Nonvolatile
memory
SII
EtherCAT
Slave Controller
Register : 0010h
Register : 0012h
(2)
(1) Node Address
Switch
(1) The Node Address Switch is set at power OFF.
(2) The value of Node Address Switch is applied to
Register: 0012 hex, when the slave power is
ON.
(3) EtherCAT master reads the set value of
Register: 0012 hex.
(4) EtherCAT master writes the value of 0012 hex
address to 0010 hex address as the node
address value.
EtherCAT Slave
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
A
A-1-2 Saving the Node Address Setting
EtherCAT master
(4)
A-1 Sysmac Device Features
A-1-2
A-3
Appendices
A-1-3
Serial Number Display
The serial number saved in the nonvolatile memory of the Vision Sensor is displayed in the Serial Number (1018-04 hex). Controllers that support Sysmac Device Features can use this serial number to
check the network configuration. To enable this check, in Sysmac Studio, set [Serial No. Check Condition] to [Set Value = Actual Unit] on the [EtherCAT Edit] screen. If the set condition is not met, a Network
Configuration Check Error will occur.
Additional Information
This network configuration check detects any slave devices that have been replaced, which
prevents you from forgetting to set parameters on those slaves.
A-1-4
Compliance with ESI Specification (ETG.2000 S (R) V1.0.1)
The ESI Specification is a set of specifications that define the entries required in an EtherCAT Slave
Information (ESI) file.
A-1-5
SII Data Check
The Slave Information Interface (SII) is an interface area in the nonvolatile memory of an EtherCAT
slave that stores the configuration information specific to that EtherCAT slave.
Sysmac Device EtherCAT slaves check the SII information from the slave side.
If one of these slaves finds that SII information with which it cannot operate was written, it generates an
SII Check Error (Error No. 88.3). If this error persists even after turning OFF and then ON the power
again, contact your OMRON sales representative.
Precautions for Correct Use
Do not use third-party or any other configuration tools to edit the SII information.
A-4
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Index
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
I
I-1
Index
Index
Numerics
C
2DCode .......................................................................... 9-3
2Form display ................................................................. 6-6
4Form display ................................................................. 6-6
A
Adding a Processing Unit ............................................. 2-27
Adding FH Device to a Project ....................................... 2-7
Adding FH Series Vision Sensor on the Network to
a Project ...................................................................... 3-3
Advanced Filter .............................................................. 9-2
Anti Color Shading ......................................................... 9-2
Application Window ........................................................ 2-8
Area
Circumference .......................................................... 4-8
Ellipse ....................................................................... 4-7
Polygon ..................................................................... 4-9
Rectangle .................................................................. 4-6
Wide arc ................................................................... 4-8
Wide line ................................................................... 4-7
area editing button .......................................................... 4-6
area editing menu ........................................................... 4-6
Author ........................................................................... 2-23
B
Background Suppression ............................................... 9-2
Barcode .......................................................................... 9-3
Basic Design Flow 1 ....................................................... 2-2
Basic Design Flow 2 ....................................................... 2-4
Basic Operations of Flow Editing ................................. 2-26
Basic Operations of Scene Data .................................. 2-21
binarization levels ......................................................... 4-10
Binary ........................................................................... 4-10
Branch ............................................................................ 4-3
brightness ....................................................................... 4-9
Brightness Correct Filter ................................................. 9-2
I-2
Calculation ..................................................................... 9-3
Calibration Support Tool ........................................ 2-33, 8-3
Camera Calibration ........................................................ 9-3
Camera Image Input ...................................................... 9-2
Camera Image Input FH ................................................. 9-2
Camera Image Input HDR .............................................. 9-2
Camera Image Input HDR Lite ....................................... 9-2
Camera Switching .......................................................... 9-2
Category ......................................................................... 2-5
Changing the image display settings ............................. 6-6
Image layout ............................................................. 6-6
Image mode .............................................................. 6-6
Positions ................................................................... 6-6
Sub image ................................................................ 6-6
Changing the System Environment ................................ 8-8
Character Inspection ...................................................... 9-3
Checking Measurement Results .................................... 6-4
Checking Multiple Measurement Images
at the Same Time ........................................................ 6-6
Checking Result Output ................................................. 6-7
Circle Angle .................................................................... 9-3
Circle Regression ........................................................... 9-3
Circular Scan Edge Position .......................................... 9-2
Circular Scan Edge Width .............................................. 9-2
Classification .................................................................. 9-2
Color ............................................................................. 4-10
Color Data ...................................................................... 9-3
Color Extraction .............................................................. 4-9
Color Gray Filter ............................................................. 9-2
Command Customize Setting Tool ................................. 8-2
Comment ...................................................................... 2-23
Communication command customize .......................... 2-33
Comparison with FH Series Unit Functions .................. 2-33
Compensate Image ........................................................ 4-2
Conditional Branch ......................................................... 9-3
Configuring Measurement Settings ................................ 4-1
Connecting with a Vision Sensor .................................... 3-1
Control Flow Fieldbus .................................................... 9-4
Control Flow Normal ...................................................... 9-3
Control Flow Parallel ...................................................... 9-4
Control Flow PLC Link ................................................... 9-4
Convert Position Data .................................................... 9-3
Copying a File ................................................................ 8-4
Creating a New Project .................................................. 2-5
Creating a New Project File from the Project Window ... 2-5
Creating and displaying dedicated dialog boxes .......... 2-33
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Index
D
Data Logging ...................................................................9-3
Data management for a single FH vision sensor ..........2-33
Data management for all devices .................................2-33
Data Output .....................................................................9-4
Data save ..................................................... 2-16, 2-19, 9-3
Date Verification ..............................................................9-3
Defect ..............................................................................9-3
Deleting FH Device from a Project ..................................2-7
Description of Screen Components ................................2-8
Designing Exchange with External Devices ....................5-1
Detail result ................................................ 2-14, 2-17, 2-19
Detection Point ...................................................... 4-11, 9-3
Device .............................................................................2-5
DI Branch ........................................................................9-3
Display Image File ..........................................................9-4
Display Last NG Image ...................................................9-4
Display Result .................................................................4-3
Downloading and uploading setting values ...................2-33
E
F
Fieldbus Data Output ......................................................9-4
File save .......................................................................2-33
File Save Tool .................................................................8-4
File selection section ...........................................2-16, 2-19
Filtering ...........................................................................9-2
Fine Matching .................................................................9-3
Flexible Search ...............................................................9-2
Flow .....................................................................2-14, 2-17
Flow display ..................................................................2-18
Flow viewer ...................................................................2-33
Focus ..............................................................................9-3
Function List .................................................................2-31
G
I
Get Unit Data ..................................................................9-3
Get Unit Figure ...............................................................9-3
Glue Bead Inspection .....................................................9-3
Gravity and Area .............................................................9-2
H
EC Circle Search ............................................................9-2
Ec Corner ........................................................................9-2
Ec Cross .........................................................................9-2
ECM Search ....................................................................9-2
Edge Pitch .......................................................................9-2
Edge Position ..................................................................9-2
Edit Pane ......................................................................2-11
Editing a Processing Unit ................................................4-4
Editing an Area ..........................................................4-6
Parameter Settings ...................................................4-5
Editing an Area ...............................................................4-6
Elapsed Time ..................................................................9-3
End ..................................................................................9-3
Ending a Connection in the Multiview Explorer ...............3-9
Ending a Connection in the Sensor
Connection Screen .......................................................3-8
Ending a Connection with a Vision Sensor .....................3-8
Entering Scene Group Information ...............................2-25
Entering Scene Information ..........................................2-23
Establishing an Online Connection from
the Multiview Explorer ..................................................3-6
Establishing an Online Connection from
the Sensor Connection Screen ....................................3-4
Establishing an Online Connection with
a Vision Sensor ............................................................3-4
EtherCAT ........................................................................5-2
Ethernet ..........................................................................5-2
EtherNet/IP .....................................................................5-2
Extract Color Filter ..........................................................9-2
Help ..............................................................................8-10
hue ..................................................................................4-9
I
Image Control Area .......................................................4-11
Image control section ...........................................2-16, 2-19
Image Conversion Logging .............................................9-3
Image display area ..............................................2-13, 2-15
Image display settings .........................................2-15, 2-17
Image file saving ...........................................................2-33
Image Logging ................................................................9-3
Image size control section ...................................2-13, 2-16
Image Subtraction ...........................................................9-2
Input Image .....................................................................4-2
Intersection .....................................................................9-2
Iris ...................................................................................9-3
L
Label Data ......................................................................9-3
Labeling ..........................................................................9-3
Limitations .......................................................................9-1
Line Regression ..............................................................9-3
List ................................................................................4-11
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
I-3
Index
M
R
Machine Simulator .......................................................... 9-2
Macro ............................................................................. 9-3
Macro Calculation ........................................................... 9-3
Managing Processing Units .......................................... 2-28
Managing Scene Groups .............................................. 2-24
Managing Scenes ......................................................... 2-22
Measure .............................................................. 2-16, 2-19
Measurement ................................................................. 4-2
Measurement Image Switching ...................................... 9-2
Measuring Camera Images ............................................ 6-2
Menu Bar ........................................................................ 2-9
Model Dictionary ............................................................. 9-3
Monitor window ............................................................ 2-12
Movement Multi Points ................................................... 9-3
Movement Single Position .............................................. 9-3
Multiview Explorer ........................................................ 2-10
N
NG analyzer ................................................................. 2-33
O
Offline Debugging ........................................................... 7-1
Offline Simulation ........................................................... 7-2
Opening the File Save Tool ............................................ 8-4
Output Result ................................................................. 4-3
Overview of Processing Units ........................................ 4-2
P
Panorama ....................................................................... 9-2
Parallel Data Output ....................................................... 9-4
Parallel I/O ...................................................................... 5-2
Parallel Judgment Output ............................................... 9-4
Parallelize ....................................................................... 9-3
Parallelize Task .............................................................. 9-3
Parameter Settings ......................................................... 4-5
Performing Test Measurement ....................................... 6-2
PLC Master Calibration .................................................. 9-3
Polar Transformation ...................................................... 9-2
Position Compensation .................................................. 9-2
Position Data Calculation ............................................... 9-3
Precise Calibration ......................................................... 9-3
Precise Defect ................................................................ 9-3
Processing unit
Copy ....................................................................... 2-28
Delete ..................................................................... 2-28
Edit ......................................................................... 2-28
Load from file .......................................................... 2-28
New folder .............................................................. 2-28
Paste ...................................................................... 2-28
Rename .................................................................. 2-28
Save to file .............................................................. 2-28
project ............................................................................. 1-3
Project Management ...................................................... 1-3
I-4
Reference Calib Data ..................................................... 9-3
Reference Point ........................................................... 4-11
Reference position batch conversion tool .................... 2-33
Registered image management tool ............................ 2-33
Result Display ................................................................ 9-4
Robot Data ..................................................................... 9-3
RS-232C/422 ................................................................. 5-2
S
saturation ....................................................................... 4-9
Saving a Logging Image as a File .................................. 8-6
Saving Measurement Results ........................................ 6-8
Saving Settings Data ...................................................... 6-9
Scan Edge Position ........................................................ 9-2
Scan Edge Width ........................................................... 9-2
Scene
Copy ....................................................................... 2-22
Delete ..................................................................... 2-22
Load from file .......................................................... 2-22
Paste ...................................................................... 2-22
Save to file .............................................................. 2-22
Scene data editing screen ............................................ 2-18
Scene group
Copy ....................................................................... 2-24
Delete ..................................................................... 2-24
Load from file .......................................................... 2-24
Paste ...................................................................... 2-24
Save to file .............................................................. 2-24
Scene group data (scene data) ...................................... 1-3
Scene group data conversion tool ................................ 2-33
Scene group Name ...................................................... 2-25
Scene maintenance area ............................................. 2-17
Scene maintenance window ........................................ 2-15
Scene Name ................................................................ 2-23
Screen customization and screen layout control .......... 2-33
Search ............................................................................ 9-2
Searching for a Processing Unit ................................... 2-30
Searching for a Scene .................................................. 2-23
Security settings ........................................................... 2-33
Selective Branch ............................................................ 9-3
Sensitive Search ............................................................ 9-2
Sensor connection screen ............................................ 2-11
Set Unit Data .................................................................. 9-3
Set Unit Figure ............................................................... 9-3
Shape Search II ............................................................. 9-2
Shape Search III ............................................................ 9-2
Single simulation .......................................................... 2-33
Stage Data ...................................................................... 9-3
Statistics ......................................................................... 9-3
Status display area .............................................. 2-13, 2-15
Stripes Removal Filter II ................................................. 9-2
Support Measurement .................................................... 4-3
Switching Scene Groups .............................................. 2-23
Switching Scenes ......................................................... 2-22
System data ................................................................... 1-3
System data editing screen .......................................... 2-19
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
Index
T
Test measurement settings ...........................................2-17
Tool data .........................................................................1-3
Tool settings editing screen ...........................................2-20
Toolbar ............................................................................2-9
Toolbox ..........................................................................2-20
Transferring Project Data to a Sensor .............................3-7
Trapezoidal Correction ....................................................9-2
Trend Monitor ..................................................................9-3
Troubleshooting ............................................................10-1
U
User Data ........................................................................9-3
User Data Setting Tool ....................................................8-7
User data tool ................................................................2-33
I
V
Vision Master Calibration ................................................9-3
W
Wait .................................................................................9-3
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
I-5
Index
I-6
Vision System FH Series Operation Manual for Sysmac Studio (Z343)
OMRON Corporation
Industrial Automation Company
Authorized Distributor:
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
© OMRON Corporation 2013 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
Cat. No. Z343-E1-01
0613
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement