VISION
PATIO AWNING
INSTALLATION GUIDE
Rev. 042015
RV AWNING PRODUCTS
1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (949) 259-4000 FAX (949)276-5500
WWW.GIRARDRV.COM
Girard Systems awnings may be operated in light wind and rain conditions. When periods of heavy rain and or high wind are expected the awning must be closed. Never leave the Awning open and unattended.
Damage caused by wind and rain is not covered by warranty.
All awnings must be closed prior to moving the vehicle for any reason.
As an extra safety precaution a visual check that every awning is fully closed is required.
Damage caused by failure to comply with these instructions is not covered by warranty .
Before using your awning, ensure that the area into which the awning will be deployed is free of obstructions (Trees, walls, pillars, posts, other vehicles etc.)
Damage caused by collisions with any of the above or similar is not covered by warranty.
Before using your awning make sure that all of your electrical circuits are operating correctly. Recreational Vehicles can generate AC power from three separate sources. The electrical system transfer switch in your vehicle will select power for the awning as follows:
Shore Power – if connected;
Generator Power – if the generator is running;
Inverter Power – batteries must be charged for inverter operation.
Girard Systems awnings are supplied with an electric motor appropriate to the product.
2
CONTENTS
Basic System Overview ………………………………………………………………………………………….… 4
Installation Instructions …………………………………………………………………………………………... 5
Product Description ……………………………………………………………………………………………….… 6
Tools Required ……………………………………………………………………………………………………….. 6
A. Unpacking ………………………………………………………………………………………………………. 7
B. Layout and Mounting the Brackets ……………………………………………………………………. 8
Awning Bracket placement chart …………..…………………………………………………………………. 9
C. Mounting the Awning …………………………………………………………………………………….. 10
D. Motion Sensor …………………………………………………………………………………………….…. 11
Testing and Adjustments ………………………………………………………………………………………. 12
A. Adjusting Motor Limit Switches …………………………………………………………………... 12-13
B. Adjusting Pitch ………………………………………………………………………………………………. 14
C. Testing the Motion Sensor ……………………………………………………………………………… 15
D. Adjusting the Lead Rail ………………………………………………………………………………….. 15
Troubleshooting Guide ……………………………………………………………………………………… 16-18
Exploded Diagram ……………………………………………………………………………………………… 19
Component Identification ………………………………………………………………………………….. 20-21
THE G–LINK SYSTEM
The G-Link motors and control modules provided by Girard Systems communicate by use of RF signals on a frequency of 433.92 MHZ. This eliminates the need for wiring and the drilling of holes in the vehicle. These components must be electronically matched, programmed or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must refer to the appropriate manual for the devices applicable to their particular installation.
3
BASIC SYSTEM OVERVIEW
The VISION Awning consists of three main components:
1.
Mechanical system – consisting of:
• The enclosure (or cassette) protects the awning while closed.
• The roller tube which is mounted within the cassette.
• The top cover or fabric rolled onto the roller tube and connected to the lead rail that extends from the enclosure when the awning is opened.
• The folding arms that supports the lead rail and the fabric.
• The tubular motor which is mounted inside of the roller tube that controls the extension and retraction of the awning.
2.
Electronic controls – to power and operate the motor:
G-Links Electronics Kit: 98GCK-18
• 98GC136 – 110V Motor controller
• 98GC779G – 12V Motion Sensor
• 98GC230 – 2 Channel, wireless wall switch.
• 98GC105A – 5 Channel, wireless handheld remote.
Please refer to the 98GCK-18 instructions/ programming guide with any questions regarding these electronic components.
4
INSTALLATION INSTRUCTIONS
FOR PERSONAL SAFETY AND QUALITY OF INSTALLATION, A MINIMUM OF
TWO INSTALLERS IS RECOMMENDED FOR THIS PRODUCT.
Before beginning to install the awning please verify the following;
• The vehicle is parked and leveled on suitable hard standing.
• Suitable precautions have been taken to protect the vehicle from accidental damage.
• The area of the vehicle where the awning is to be installed has been prepared.
• Sufficient manpower, a minimum of 2 persons is required.
• Suitable protective clothing is worn by the persons doing the installation.
• Suitable and serviceable lifting and holding equipment should be used to avoid personal injury.
• When mounting fixtures to the vehicle be aware that the soft materials that the skin of the vehicle is made from can be torn out or “Stripped” by the over tightening of fasteners.
DO NOT OVER TIGHTEN FIXING BOLTS AND SCREWS.
• Make every effort to ensure that fasteners are mounted to the structural framework of the vehicle not just the skin.
• Any holes made in the skin of the vehicle must be sealed with silicone sealant, putty tape or similar product.
WARNING
ALL ELECTRICAL WORK MUST CONFORM TO APPLICABLE
ELECTRICAL CODES AND STANDARDS.
• Turn off power before beginning any electrical work.
• Please consult your RV’s wiring diagram to locate any wiring prior to any drilling or any installation procedures.
• Ensure that placement of controls, cables, and wires are not in any way obstructed. This can damage the components and obstruct electrical current.
• Use only certified components .
5
PRODUCT DESCRIPTION
The VISION is a dual pitch awning system provides protection from the sun at a touch of a button. The VISION awning is built to your specifications with the highest quality materials available, your unit features:
• A standard motor that operates with a wireless motor controller or a wireless motor that operates with an integrated motor control.
• Motion Sensor that will retract the awning to prevent damage from the wind.
• A hand held Remote Control
• A wall mounted Remote Switch
• Options include; electronic automation controls to ensure proper closing at all times, a control to retract all awnings when the vehicles’ motor is started, and more….
• Electric Drill
TOOLS REQUIRED
• Tape measure
• (2) ladders
• Chalk line
• Flat head screwdriver (small)
• Phillips screwdriver
• Caulking gun
• (2) tubes silicone caulking
• Drill bits: 1/8”, 3/8”, and 7/16”
• Open-end wrenches: 13mm (1/2”), 17mm and 19mm.
• Keyhole saw
6
A.
UNPACKING
Before starting any of the installation procedures:
1.
Unpack the awning and inspect the product for any possible damage that may have occurred during shipping.
2.
Ensure that the length and motor placement of your awning are correct.
3.
When you have determined that the product is to your satisfaction, remove the mounting brackets and place the awning in a safe location while preparing the RV. a.
To remove the brackets locate the slide lock that retains the bracket to the housing. (Figure 1) b.
Using a 13mm or ½” wrench, loosen all set screws on the slide locks. c.
Once the set screws have been loosened the slide locks should slide freely, clear the slide lock away from the bracket.
4.
If you have discovered any damage or missing parts please contact your supplier.
SLIDE LOCK
SET SCREW
Figure 1
MOUNTING BRACKET
7
B.
LAYOUT AND MOUNTING THE BRACKETS
1.
MOUNTING THE AWNING – NOTE: The clearances needed for mounting the VISION varies by manufacturer. The shape of the roof, the depth of installation and all other factors should be taken into consideration when installing this product. Please consult Girard Systems if there are any questions regarding your installation. a.
Determine the exact position for the final installation of the awning. b.
Mounting brackets must be installed within 6” of the ends of the awning.
Once you have determined the location of the two end brackets snap a chalk line between the two points to ensure alignment of the installation. You will be able to reference this line to install the smaller middle brackets at a later time. c.
To find the location of the smaller middle brackets please refer to the chart on the following page. NOTE: The placement of the middle brackets must comply with the VISION BRACKET PLACEMENT CHART. Failure to follow these instructions will void the warranty of this product. d.
Now that you have determined the bracket locations, using the bracket as your template, mark the holes for mounting the bracket. e.
Fix the brackets to the roof of the vehicle using appropriate sized fasteners.
NOTE: It is up to the installer to find adequate structure to securely fasten the mounting brackets to. All caution must be taken to weather seal all installation perforations. Failure to do this could
result in damage to the vehicle.
NOTE: Please consult your RV’s wiring diagram to ensure that no wiring will be damaged while drilling any holes.
8
9
C.
MOUNTING THE AWNING
1.
Lift the awning into position for fastening to the mounting brackets. a.
Ladders are usually sufficient however a scaffold or forklift may be used. b.
If using a forklift use all necessary caution to protect the surface of the awning. Lift from the center of the awning to maintain product balance while elevating.
2.
Place the awning onto the brackets. Make sure the grooves of the awning are securely engaged into the channels on the bracket. (Figure 3)
3.
Secure the awning by moving the slide locks along the bottom awning track until they are located under their respective brackets.
4.
Once the final location of the slide locks has been achieved, tighten all set screws on each slide lock with a 13mm or ½” wrench.
Set Screw
Slide Lock Mounting Bracket
(FIGURE 3)
Shoulder Assembly
10
D. MOTION SENSOR
NOTE: The Motion Sensor requires a hard wired 12V. D.C. connection.
12v DC MOTION SENSOR (Hard wired)
The Motion Sensor will come from the factory pre-programmed.
A hole may need to be drilled for the power cable.
1.
Locate the cable at the back of the awning cassette.
2.
Locate the nearest source of 12V. D.C. power.
3.
If required drill an appropriate sized hole, then feed the cable into the interior of the vehicle and connect to a 12V. D.C. source or connect into an exterior junction box with a 12V DC source.
4.
If necessary refer to the Motion sensor manual for instructions to program the motion sensor.
Motion Sensor
11
TESTING AND ADJUSTMENTS
OVERVIEW
A. Adjusting Motor-limit switches
B. Adjusting Pitch
C. Testing the Anemometer
D. Adjusting Lead Rail
A. ADJUSTING MOTOR LIMIT SWITCHES
TOOLS REQUIRED
Black plastic key provided with awning, or 4mm (5/32”) Allen wrench.
NOTE: The motor limit switches have been adjusted to the correct positions at the factory prior to shipment. When fully retracted the awning motor is set to stop the exact moment the awning box closes. When fully extended the fabric should be taut and the arms should be slightly bent, exposing a gap of about ¼” at the elbows.
Always check the motor limits after installation to ensure that the awning opens and closes correctly. Awning fabric can stretch over time, this will require an adjustment of the OUT limit switch.
IMPORTANT: EXTREME CARE SHOULD BE TAKEN TO ENSURE THAT THE
MOTOR LIMIT TURNS OFF AT THE EXACT MOMENT THE AWNING BOX
CLOSES. FAILURE TO DO SO WILL CAUSE THE MOTOR TO RUN WHEN THE
AWNING IS CLOSED. THIS WILL SIGNIFICANTLY REDUCE THE LIFE OF THE
MOTOR.
1.
The AC motors used in Girard Systems awnings are reversible. Any reference made to the motor limit switches in these instructions is based on the right-hand placement of the motor. For left hand placement, simply reverse the instructions.
2.
The motor has limit settings for both OUT (extension) and IN (retraction).
3.
The limit switches can be adjusted by use of the black key provided with the awning, or you may use a 4mm (5/32”) Allen wrench.
12
4.
Extend the awning a few feet to gain access to the motor. Locate the motor
(standard installation is on the right hand side of the awning). The limit adjustment pots are located on the head of the motor. Using the symbols printed next to the adjustment pots, turn the black key (or 4mm Allen wrench) to make the necessary adjustments. Typically, the motors are labeled with a + or a -.
(Figure 5)
IN LIMIT
ADJUSTMENT
OUT LIMIT
ADJUSTMENT
MANUAL
CRANK PORT
(Figure 5)
5.
Approximately ¼ turn of the adjustment pot represents about 1” of awning movement. NEVER set outward limits so that the fabric is slack with full arm extension. For proper adjustment set limit switch to stop the motor just before the arms lock. This will expose about a 1/4” gap at the elbow.
13
B. ADJUSTING PITCH
NOTE: This adjustment is usually required after an arm replacement. Also, if the elbow of the arm hits the bottom of the casing as the lead rail closes.
Tools Required
• 19mm (3/4”) open-end wrench
ADJUST
LOCK
(Figure 6)
1.
ADJUSTING PITCH a.
Extend the awning about 18”. b.
On the arm selected, loosen the lock nut on the side of the shoulder assembly using a 19mm open-end wrench. (Figure 6) c.
Locate the adjustment bolt located on the front of the shoulder assembly (Figure 6).
Using a 19mm open-end wrench rotate the bolt counter-clockwise to Raise the pitch or clockwise to Lower the pitch.
DO NOT OVERTIGHTEN AS THIS WILL RESULT IN DAMAGE TO THE
AWNING. d.
Tighten the lock nut located on the side of the shoulder assembly. e.
Close the awning completely to ensure smooth operation and that the lead rail lies flush and square along the length of the cassette.
14
C. TESTING THE MOTION SENSOR
1.
Partially extend the awning.
2.
Physically activate the Motion sensor by pulling down the corner of the lead rail about 12” and then release. This should create enough movement to activate the motion sensor.
3.
At this point the awning should retract; if not, check the electrical connections to the selected power source.
NOTE: The motion sensor will only retract the awning on which it is mounted.
When testing the system verify all of the awnings will close properly from the fully extended position.
If the system does not operate correctly under these conditions you may: a.
Provide sufficient power from your panel. b.
Try reprogramming the motion sensor.
D. ADJUSTING THE LEAD RAIL
The lead rail has been preset at +/- 3 degrees. This allows it to rest firmly into the cassette and creates a weather resistant seal for travel. To alter the pitch angle, at each lead rail connector loosen the lock nut with a 17mm wrench then insert a 5mm Allen wrench into the Pitch adjustment screw. Turn clockwise to increase or counterclockwise to decrease the pitch (Figure 8) and then tighten the lock nut.
PITCH ADJUSTMENT
LOCK NUT
Fig 8
15
TROUBLESHOOTING GUIDE
PROBLEM:
The lead rail is binding on the side of the awning casing; i.e. the rail is offset from housing.
SOLUTION:
• Open the awning about 3 feet.
• Loosen the lead rail adjustment screws on all arms.
• Locate and remove the two fabric set screws that are on each end of the lead rail. The lead rail is now ready to be shifted.
• Retract the awning until the lead rail is about 4 inches from the fully closed position.
• Using a rubber mallet, tap the end of the lead rail to move it into the correct position.
• When proper alignment has been achieved tighten the lead rail adjustment screws (Figure 9), and then replace the fabric screws. (Figure 10)
LEAD RAIL ADJUSTMENT
Fig.9
16
FABRIC SCREW
Fig 10
PROBLEM:
The motor side of the awning closes when the awning is retracted but the opposite end does not.
SOLUTION:
Refer to “Adjusting the Lead Rail” on page 20. If this does not solve the issue please call the Girard Systems service line at (949)259-4000 or toll free at (800)382-8442.
PROBLEM:
Motor will not operate.
SOLUTION:
• Check that all of the GFI switches in the vehicle are turned on.
• If your vehicle has an Awnings Power Main Switch, locate that switch and make sure it is in the ON position.
• Check that the motor’s thermal protection circuit breaker has not tripped. The
110V AC motor supplied in your VISION Awning is designed for intermittent use and may cut out temporarily if it has overheated. When this occurs you must
17
allow the motor to cool so that the internal circuit breaker can reset. This may take up to an hour depending on the outside temperature. You may use a manual crank during this period.
• If this does not solve the issue please call the Girard Systems service line at
(949)259-4000 or toll free at (800)382-8442.
PROBLEM:
The motor will operate for 10-12” and then stop.
SOLUTION:
The motor may not be receiving enough power to operate correctly.
• Check to ensure that you have a minimum of 10 amps, if not switch on your generator or connect to shore power.
• If this does not solve the issue please call the Girard Systems service line at
(949)259-4000 or toll free at (800)382-8442.
PROBLEM:
The fabric is loose when the awning is fully extended; i.e. the roller keeps turning after the awning arms have locked open.
SOLUTION:
The motor’s OUT limits must be reset to factory standards. Please refer to the
“Adjusting the Motors Limit Switches” section on page 16-17.
PROBLEM:
The motor stops before the lead rail has closed completely into the awning cassette on either or both sides. There is no apparent binding of the awning components.
SOLUTION:
The VISION Awning is equipped with a manual override motor which has manual limit settings. The IN limit may need to be adjusted to allow the box to be closed tighter.
Refer to the “Adjusting the Motors Limit Switches” section of this manual.
PROBLEM:
As the awning is closing, the elbow of one or more of the arms is hanging down preventing the case from closing.
SOLUTION:
Please refer to the “Adjusting pitch” section of this manual.
18
19
COMPONENT IDENTIFICATION
ITEM
1
16
17
18
12
13
14
15
10
10
10
11
9
9
8
9
7
7
6
7
6
6
5
5
4
5
4
4
3
3
2
3
DESCRIPTION
ROLLER TUBE CENTER SUPPORT BRACKET ASSEMBLY
MAIN HOUSING ARM SUPPORT GUIDE
VISION 16’ COVER HOUSING
VISION 18’ COVER HOUSING
VISION 22’ COVER HOUSING
VISION 16’ RUBBER GASKET
VISION 18’ RUBBER GASKET
VISION 18’ RUBBER GASKET
VISION BACK HOUSING 16’
VISION BACK HOUSING 18’
VISION BACK HOUSING 22’
ROLLER TUBE / LEAD RAIL POLY ROPE 16’ (2)
ROLLER TUBE / LEAD RAIL POLY ROPE 18’ (2)
ROLLER TUBE / LEAD RAIL POLY ROPE 22’ (2)
VISION ROLLER TUBE 16’
VISION ROLLER TUBE 18’
VISION ROLLER TUBE 22’
VISION GUDGEON
VISION 16’ PLASTIC FABRIC GUIDE
VISION 18’ PLASTIC FABRIC GUIDE
VISION 22’ PLASTIC FABRIC GUIDE
VISION 16’ FABRIC GUIDE SUPPORT
VISION 18’ FABRIC GUIDE SUPPORT
VISION 22’ FABRIC GUIDE SUPPORT
VISION COVER PLATE ASSEMBLY LH
VISION LOCK PLATE ASSEMBLY LH
VISION ROLLER TUBE SUPPORT BRACKET ASEMBLY (2)
VISION GUDGEON BUSHING
VISION PLASTIC GUDGEON WASHER
VISION MAIN HOUSING GUIDE ASSEMBLY (2)
VISION SHOULDER SUPPORTASSEMBLY LH
VISION CROSSBAR ENDCAP (2)
PART NUMBER
7010001-1
7010003-8
7010016-9
7010018-9
7010022-9
7010016-10
7010018-10
7010022-10
701L004-11
701L005-12
7010006-13
7010007-14
7010008-15
7010009-16
701L010-17
7010011-18
7010002-2
7010016-3
7010018-3
7010022-3
7010016-4
7010018-4
7010022-4
7010016-5
7010018-5
7010022-5
7010016-6
7010018-6
7010022-6
7010016-7
7010018-7
7010022-7
20
40
42
43
44
36
36
36
38
44
44
45
49
33
34
34
34
29
32
33
33
23
24
25
28
19
20
21
22
VISION 19.5” MOUNTING BRACKET W/SLIDE LOCK
VISION 11.5” MOUNTING BRACKET W/SLIDE LOCK
VISION CROSSBAR PIN ASSEMBLY (2 or 3)
VISION ARM ASSEMBLY 10’ LH
VISION LEAD RAIL CONNECTOR ASSEMBLY LH
VISION LEAD RAIL GUIDE ASSEMBLY (2)
VISION LEAD RAIL ENDCAP ASSEMBLY LH
VISION COVER PLATE ASSEMBLY RH
VISION LOCK PLATE ASSEMBLY RH
VISION SHOULDER SUPPORT ASSEMBLY RH
VISION 16’ CROSSBAR PLASTIC FABRIC GUIDE
VISION 18’ CROSSBAR PLASTIC FABRIC GUIDE
VISION 22’ CROSSBAR PLASTIC FABRIC GUIDE
VISION 16’ CROSSBAR
VISION 18’ CROSSBAR
VISION 22’ CROSSBAR
VISION 16’ (32’) CROSSBAR STRING
VISION 18’ (36’) CROSSBAR STRING
VISION 22’ (44’) CROSSBAR STRING
VISION ARM ASSEMBLY 10’ RH
VISION LEAD RAIL CONNECTOR ASSEMBLY RH
VISION FABRIC SCREW ANCHOR
VISION FABRIC SCREW
VISION 16’ LEAD RAIL
VISION 18’ LEAD RAIL
VISION 22’ LEAD RAIL
VISION LEAD RAILEND CAP ASSEMBLY RH
VISION LEAD RAIL ARM SUPPORT (2 or 3)
NOTE: WHEN QUOTING/WRITING PART NUMBERS ADD A “B” OR “W” ON
THE END FOR COLOR WHERE REQUIRED.
7010016-36
7010018-36
7010022-36
701R022-38
701R023-40
7010024-42
7010025-43
7010016-44
7010018-44
7010022-44
701R026-45
7010027-49
7010012-19
7010013-20
7010014-21
701L015-22
701L016-23
7010017-24
701L018-25
701R019-28
701R020-29
701R021-32
7010016-33
7010018-33
7010022-33
7010016-34
7010018-34
7010022-34
21
