Advertisement
Advertisement
AirWave 8.2.5
Supported Infrastructure Devices
AirWave provides a range of features to manage network infrastructure devices from Aruba Networks and other vendors. This document describes the supported product families, software versions, and feature set for the following product sets: l l l l l
"Hewlett Packard Enterprise Devices" on page 5
"Third-Party Vendor Devices" on page 7
n n n n
"Motorola® Devices" on page 11
"Other Third-Party Devices with Monitoring Support" on page 12
Aruba Devices
AirWave supports management of global configuration profiles or settings, monitoring, and software upgrades on Aruba devices and software that are running ArubaOS 6.5.0.0, 6.5.1.0, 6.5.2.0. AirWave supports only monitoring on Aruba devices running ArubaOS 8.0.0. The sections that follow provide support matrices for integration with Aruba devices.
ArubaOS
AirWave supports all Aruba controllers and most access points (APs) that are running ArubaOS 6.5.0.0, 6.5.1.0,
6.5.2.0, 8.0.0.0, 8.0.1.0, 8.1.0.0, 8.1.0.2, 8.1.0.3, and 8.2 and have not reached the end of life milestone. Refer to http://www.arubanetworks.com/support-services/end-of-life/ for the complete list of products that have reached the end-of-life milestone.
AirWave supports Aruba unified APs; access points that are factory-installed with ArubaOS 6.5.2.0 or a later. A unified AP can be configured to operate as either a campus AP or a remote AP when that device is first provisioned. For more information on unified APs, refer to the ArubaOS 6.5.2 Release Notes .
Table 1: Supported ArubaOS Devices
Device
AP-365 and AP-367
AP-334 and AP-335
AP-324 and AP-325
AP-304 and AP-305
AP-303H
AP-277
Validated up to
6.5.2.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.2.0
6.5.0.0
Reference Guide | Supported Infrastructure Devices Rev. 02 | October 2017
2
Table 1: Supported ArubaOS Devices (Continued)
Device
AP-274 and AP-275
AP-224 and AP-225
AP-228
AP-207
AP-203H
AP-203R and AP-203RP
AP-205H
AP-214 and AP-215
AP-204 and AP-205H
AP-175
AP-134 and AP-135
AP-114 and AP-115
AP-124 and AP-125
AP-104 and AP-105
AP-103
AP-103H
AP-92 and AP-93
AP-93H
AP-68
3000 Series Controller
7005 Controller
7010 Controller
7024 Controller
7030 Controller
7200 Series Controller
7280 Controller
Validated up to
6.5.0.0
6.5.0.0
6.5.0.0
6.5.4
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.1.0
6.5.2.0
6.5.2.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
6.5.0.0
Reference Guide | Supported Infrastructure Devices
The AP-80M series of access points is not supported by AirWave.
Aruba Instant
AirWave supports Aruba Instant Access Points running Instant software 6.5.4 and all prior versions that have not reached the end of support milestone. In addition, AirWave supports the Aruba RAP-100 Series and RAP-3 Series remote access points.
Table 2: Supported Aruba Instant Devices
Instant Version
Template Config
Support for
Instant GUI Config
Instant 6.5.4
AirWave 8.2.5
AirWave 8.2.5
Instant 6.5.3
Instant 6.5.2
Instant 4.3.1
Instant 4.3.0
Instant 4.2.4
Instant 4.2.3
AirWave 8.2.4.1
AirWave 8.2.4
AirWave 8.2.3.1
AirWave 8.2.3.0
AirWave 8.2.1
AirWave 8.2.0
AirWave 8.2.4.1
AirWave 8.2.4
AirWave 8.2.3.1
AirWave 8.2.3.0
AirWave 8.2.2
AirWave 8.2.2
Starting with 6.4.3.x-4.2, Instant software does not support IAP-92 and IAP-93.
Aruba Switches
AirWave supports monitoring, template configuration, and firmware changes on the Aruba switches listed in
If you want to see the SNMP traps, go to the System > Syslog & Traps page.
In addition, you can push a complete configuration profile using templates to Aruba switches that have a factory-default configuration, or you can send partial configuration changes to the devices in a group.
In VisualRF, these Aruba switches appear in the VisualRF product catalog. However, their utilization values will be 0 because AirWave does not get utilization values for these devices.
Table 3: Supported Aruba Switches
Device Monitoring Configuration Firmware
Upgrade
Aruba 2530YA Yes Yes Yes
Aruba 2530YB Yes Yes Yes
Validated Firmware
Version
YA.16.04.0008
YB.16.04.0008
Reference Guide | Supported Infrastructure Devices 3
4
Table 3: Supported Aruba Switches (Continued)
Device Monitoring Configuration Firmware
Upgrade
Aruba 2540 Yes Yes Yes
Yes
Yes
Aruba 2620
Aruba 2920
Aruba 2930F
Aruba 2930M
Aruba 3800
Aruba 3810
Aruba 5400R
Aruba 5406zl
Aruba 5412zl
Aruba 8400
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
No
Validated Firmware
Version
YC.16.04.0008
RA.16.04.0008
WB16.04.0008
WC.16.04.0008
WC.16.04.0008
KA.16.04.0008
KB.16.04.0008
KB.16.04.0008
K.16.01.0007
K.16.01.0007
10.00.0002
Aruba Mobility Master Applicances
AirWave supports the following devices running ArubaOS 8.0.0 and later: l l
Mobility Master Hardware Appliance MM-HW-1K, MM-HW-5K, and MM-HW-10K
Mobility Master Virtual Appliance MM-VA
Aruba Mobility Access Switches
AirWave supports profile configuration, monitoring, and software upgrades on the Aruba Mobility Access
Switches. In addition to the port statistics supported for most Ethernet switches with the supported firmware described below, AirWave also tracks the activity of authenticated wired clients on Aruba switches.
Table 4: Supported Aruba Mobility Access Switches
Device
S1500
S2500
S3500
Validated up to
7.4.0.0
7.4.0.0
7.4.0.0
Aruba AirMesh
Aruba AirMesh outdoor products running MeshOS 4.2 are supported for monitoring and software upgrades.
Reference Guide | Supported Infrastructure Devices
Table 5: Supported Aruba MeshOS Devices
Device
MSR1200
MSR2000
MSR4000
MST200
Validated up to
MeshOS 4.2
MeshOS 4.2
MeshOS 4.2
MeshOS 4.2
Hewlett Packard Enterprise Devices
The firmware versions for the HPE devices listed
represent the latest firmware version verified as fully
supported by AirWave 8.2. The devices in Table 6
are available within the VisualRF product catalog and can be selected when setting up device-specific triggers and alerts. In addition, these devices can be set up as trap receivers, and the SNMP traps can be seen on the System > Syslog & Traps page.
AirWave does not support MSM APs running in autonomous mode.
Informal testing shows that AirWave supports some devices running more recent versions of firmware, but full support for these later versions is not guaranteed. For more information on configuring and managing and HPE switches via AirWave, refer to the AirWave Switch Configuration Guide .
Table 6: HPE Device Support
Model
MSM310 and MSM310R
MSM313 and MSM313R
MSM317
MSM318
MSM320 and MSM320R
MSM323 and MSM323R
MSM325
MSM335
MSM410
MSM417*
MSM422
MSM425*
MSM430
MSM460
MSM466 and 466R
MSM525*
FirmWare Validated Up To
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
Reference Guide | Supported Infrastructure Devices 5
6
Table 6: HPE Device Support (Continued)
Model
MSM527*
MSM560*
MSM710 (controller)
MSM720 (controller)
MSM730 (controller)
MSM750 (controller)
MSM760 (controller)
MSM765 (controller)
ProCurve 420
FirmWare Validated Up To
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
6.5.1.0
2.0.38 - 2.2.5
WA.01.16-WA.02.19
ProCurve 530
ProCurve 2626-PWR
830 Unified Wired-WLAN Switch*
850 Unified Wired-WLAN Switch*
870 Unified Wired-WLAN Switch* l l
HPE WESM controllers & APs xl zl
HPE 1950 Switch
H.10.35 (ROM H.08.02)
5.20.109 (Release 2607P39)
5.20.109 (Release 2607P39)
5.20.109 (Release 2607P39)
HPE 3100 Switch Series
HPE 3600 Switch Series
HPE 5120 Switch
HPE 5130 Switch
HPE 5500 Switch Series
HPE 7500 Switch Series l l
WS.01.05 – WS.02.19
WT.01.03 – WT.01.28
2220P02 (Comware 7)
2220P02 (Comware 7)
2220P02 (Comware 7)
2220P02 (Comware 7)
2220P02 (Comware 7)
2220P02 (Comware 7)
2220P02 (Comware 7)
HPE 10500 Switch Series 2220P02 (Comware 7)
* These HPE devices are not supported in VisualRF.
High Availability Support
AirWave 8.2 introduces support for pairs of HP Unified Wired-WLAN (UWW) devices operating in HA mode.
AirWave monitors the status of each controller. After AirWave detects that a failover occurred and the APs failed over to the backup controller, AirWave displays the current status of the APs.
HPE ProCurve
HPE ProCurve switches have the following additional support through AirWave:
Reference Guide | Supported Infrastructure Devices
l l
Automated discovery through SNMP
Model & software version identification
Third-Party Vendor Devices
AirWave provides basic monitoring and, in some cases, management of the third-party vendor devices listed below. The following section describes the features, and provides the list of supported devices and firmware versions.
Monitoring
AirWave supports the following basic monitoring features for third party devices, unless specified otherwise: l l l l l l
User monitoring data such as connection time, user name, SSID, and bandwidth
Network monitoring data, including real-time and historical bandwidth and user count metrics
Rogue detection and classification using AirWavecustomizable rules
VisualRF heatmaps and user/rogue location
Reports
Triggers and alerts
Management
AirWave supports the following basic management features for third party devices, unless specified otherwise: l l l Basic configuration
Firmware upgrades
Controller and AP discovery
Cisco
®
Devices
AirWave supports Cisco devices that are running the latest verified firmware versions and have not reached the end of life milestone. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not validated.
Cisco Autonomous Access Points
AirWave provides monitoring, management, and software upgrade support for the autonomous APs listed in
Table 7: Supported Cisco Autonomous Access Points
Model
702W Access Points
Validated up to
IOS: 15.3(3)JD
801 Access Points IOS 12.4(25d)JA2
IOS 15.(22)JB
IOS 12.4(15)XZ, 12.4(20)T
860 Series
881 Series IOS 12.4(21a)JA1
Reference Guide | Supported Infrastructure Devices 7
8
Table 7: Supported Cisco Autonomous Access Points (Continued)
Model Validated up to
881W Series IOS 12.4(21a)JA1
IOS 15.0(1)M7
881GW Series
891 Series
1040 Series
1100 Series
1110 Series
1130 Series
1140 Series
1200 Series
1210 Series
1230 Series
1240 Series
1250 Series
1260 Series
1300/1400 Series Bridges
1700 Series
1941W Series
2700 Series
IOS 12.4(21a)JA1
IOS 15.1(4)M3
IOS 12.4(21a)JA1
IOS 15.0(1)M7
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.3(11)JA
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.3(11)JA
IOS 12.4(21a)JA1
IOS 12.3(11)JA
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS 12.4(21a)JA1
IOS10.2.111.0 (IOS: 15.3(3)JN3)
IOS 15.2(3)T
IOS10.2.111.0 (IOS: 15.3(3)JN3)
Cisco Wireless Controllers and Access Points
AirWave supports monitoring, RAPIDS, device discovery, and VisualRF for these devices, as well as configuration, firmware identification, AMP upgrade, and client monitoring-diagnostics for wireless controllers.
lists Cisco wireless controllers and access point platforms that are supported in this release.
Reference Guide | Supported Infrastructure Devices
Table 8: Supported Cisco Wireless Controllers and Access Points
Model Validated up to
1040 Series Access Points 8.3.102.0
1130 Series AP
1140 Series Access Points
1200 Series Access Points
1550 Series Access Points
1600 Series Access Points
1700 Series Access Points
1800 Series Access Points
2600 Series Access Points
2700 Series Access Points
3500 Series Access Points
3600 Series Access Points
3700 Series Access Points
3800 Series Access Points
2100 Series Wireless Controllers
2500 Series Wireless Controllers
4400 Series Wireless Controllers
5500 Series Wireless Controllers
5760 Wireless Controllers
Flex 7500 Controllers
8510 Controllers
7.6.110.0 (Bootloader: 7.0.116.0)
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
8.3.102.0
7.0.235.0 (Bootloader: 7.0.235.0)
8.3.102.0
7.0.235.0 (Bootloader: 7.0.235.0)
8.3.102.0
3.2.0
8.3.102.0
8.0.100.0
Cisco Mobility Services Engine and 500 Series Access Points are not supported.
Cisco Switches
AirWave supports automated discovery through SNMP, model and firmware version identification, and displays
CDP neighbor information and extended port error statistics for the Cisco switches listed in
Reference Guide | Supported Infrastructure Devices 9
Table 9: Supported Cisco Switches
Model
3650 Switches
Validated up to
03.06.01E
3750 Switches
3850 Switches
12.2.55-SE11
03.06.01E
4800 Bridges (pre-VxWorks, monitoring only) 8.65_2
Juniper
®
Devices
The following Juniper controllers and APs are supported for monitoring, configuration, and software upgrades.
The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.2.5. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed.
10
Table 10: Juniper AP Support
Model
WLA321
WLA322
WLA522
WLA532
WLA632
WLC100
WLC2
WLC2800
WLC8
WLC800
WLC880
WLC JunosV
Juniper Switch
Validated up to
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
9.1.0.6.0
12.3R6.6
Juniper®
Juniper switches have the following additional support through AirWave: l l l
Automated discovery through SNMP
Model & software version identification
Rogue AP detection is supported using the Q-BRIDGE MIB
Meru
®
Devices
The following Meru controllers and APs are now supported in VisualRF.
Reference Guide | Supported Infrastructure Devices
The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.2.5. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed.
Table 11: Meru Device Support
Model Validated up to
AP302
AP320i
AP332i
AP433i
AP433is
AP822e
AP822i
AP832e
6.1.1-25
6.1.1-25
6.1.1-25
6.1.1-25
6.1.1-25
6.1.1-25
6.1.1-25
6.1.1-25
AP832i
RS4000
MC1000*
MC1550
MC3000*
MC3200
MC4200
MC5000*
6.1.1-25
6.1.1-25
3.6.1-49
6.1.1-25
3.6.1-49
6.1.1-25
6.1.1-25
3.6.1-49
*This version of AirWave supports monitoring for these devices.
VisualRF support for the for the AP433i, AP433e, AP433is, AP822i, and AP822e is not included in this release of AirWave.
Motorola
®
Devices
The following Motorola (formerly Symbol) controllers and autonomous APs are supported for monitoring, configuration, and software upgrades.
The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.2.5. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed.
Reference Guide | Supported Infrastructure Devices 11
12
Table 12: Motorola Autonomous AP, Wireless LAN Controller, and AP Support
Model Validated up to
AP621
AP622
AP650
AP5131
AP5181
AP6521*
AP6522*
AP6532*
AP7131
AP7161
RFS4000
RFS6000
RFS7000
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.20-30R
5.4.2.0-30R
5.4.20-30R
5.4.20-30R
WS2000
WS5100
2.4.5
3.3.4
Wing5 RFS controllers 5.4.20-30R
* These AP and controller models may require adjustments to the AirWave SNMP timeouts to compensate for known SNMP issues on these devices.
Other Third-Party Devices with Monitoring Support
This version of AirWave supports monitoring for a variety of devices with software versions listed in the table below.
The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.2.5. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed.
Table 13: Other Supported Devices
Device
BelAir 200
Brocade ICX switches
Ericsson APM-210 access point module
Proxim AP-600/700
Proxim AP 2000/4000
Validated up to main.2005.03.29
08.0.20T211 and 08.0.30aT213
6.4.4.0-sp
2.0 – 4.0.2
Reference Guide | Supported Infrastructure Devices
Table 13: Other Supported Devices (Continued)
Device
Proxim Tsunami MP.11 QB 954-x, 2454-x, 4954-x, 5054-x
Siemens SCALANCE W1750D
Symbol 3021
Symbol 4121/4131
Symbol 5131/5181
Trapeze MXR-2, MXR-8, MXR-20, MXR-2xx, MX-400,
MP-3x2, MP-422
Tropos 3/4/5210/5320/9422/9532
Validated up to
2.3.0 – 4.0.0
6.5.0.0 - 4.3.0
04.01-23 – 04.02-19
3.51-20 – 3.95-04
1.1.0.0.045R – 2.5.0.0
5.0.12.2 – 7.0.5.6
5.1.4.7 – 6.6.1.3
Other Switches
Some switches have additional support in AirWave:
Alcatel-Lucent OmniSwitch™ (6250 and 6450)
l l l l
Automated discovery through SNMP
Model & software version identification
Stack information
Firmware version 6.6.1.859.R01
Brocade
l l l l
Automated discovery through SNMP
Model & software version identification
Firmware version 08.0.20T211 and 08.0.30aT213
Stacking
Force10
l l
Model & software version identification
Firmware version 8.4.2.9
Reference Guide | Supported Infrastructure Devices 13
Contacting Support
Main Site
Support Site arubanetworks.com
support.arubanetworks.com
Airheads Social Forums and Knowledge Base community.arubanetworks.com
North American Telephone 1-800-943-4526 (Toll Free)
1-408-754-1200
International Telephone
Software Licensing Site
End-of-life Information
Security Incident Response Team (SIRT) arubanetworks.com/support-services/contact-support/ hpe.com/networking/support arubanetworks.com/support-services/end-of-life/
Site: arubanetworks.com/support-services/security-bulletins/
Email: [email protected]
14
© Copyright 2017 Hewlett Packard Enterprise Development LP www.arubanetworks.com
3333 Scott Blvd
Santa Clara, California 95054
Phone: 1-800-WIFI-LAN (+800-943-4526)
Fax 408.752.0626
Reference Guide | Supported Infrastructure Devices
Advertisement