Lighting Appendix
Diane Emert
Senior Thesis 2005
Broadway Plaza, Rochester, MN
Lighting Appendix
137
Diane Emert
Senior Thesis 2005
Broadway Plaza, Rochester, MN
In-pool Lighting Images
The following images were developed using Lightscape modeling of the in-pool lighting.
Realistic modeling of light in water is next to impossible due to the scattering, attenuation,
caustics, etc. involved with the physics of modeling light in water. In an attempt to gather images
to replicate the scene, undulating surfaces were created to represent small water waves and
assigned the physics template for water within Lightscape. The following images are, therefore,
obtained when attempting to replicate the lighting possible through the fiber optic system.
Figures a-b (Above): In-Pool Lighting Only
Figure c (At Left): View From Within the Pool
Striations should be created on the wall due to the reflections of light in water. These striations
are similar to those seen below and shall invoke a feeling of serenity for the occupants.
138
C1
SPECIFICATIONS - C YCLO 04
PHYSICAL
L x W x H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190 x 98 x 88 mm (50 x 4 x 3.7 in)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5 kg (12.1 lbs)
Shipping dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 1210 x 115 x 95 mm, (51 x 4.8 x 4 in)
Shipping weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.9 kg (13 lbs)
Fixture color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . white (NCS 0402-G06-Y)
INSTALLATION
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . any
Minimum free space around fixture when installed . . . . . . . . . . . . . . . . . . . 25 mm (1 inch)
SOURCE
Approved lamp type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH 28 watt tubes
Light source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T5 tubes (3x28W)
Expected lamp life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20000 hours
POWER
AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 V - 254 V, 50 / 60 Hz
Dimmer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 1-10V control
Maximum power and current @ 254 V / 60 Hz . . . . . . . . . . . . . . . . . . . . 0.56 A / 128 watts
THERMAL
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
DYNAMIC EFFECTS
Dimmable tubes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Red, green, blue and white
Independent dimming of each tube via 516 Converter
CONTROL (VIA 516 CONVERTER)
Number of independently controllable dimming channels . . . . . . . . . . . . . . . . . . . . . . . . . 16
Channels required per independently controlled Cyclo 02 group . . . . . . . . . . . . . . . . . . . . . 2
Channels required per independently controlled Cyclo 03 group . . . . . . . . . . . . . . . . . . . . . 3
Channels required per independently controlled Cyclo 04 group . . . . . . . . . . . . . . . . . . . . . 4
Number of Cyclos per group (fixtures wired in series) . . . . . . . . . .1-10 (of the same model)
ORDERING INFORMATION
Cyclo 04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90550000
INCLUDED ITEMS
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/60 (red)
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH 28W/66 (green)
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/67 (blue)
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/840 (white)
User manual
C1
I NTRODUCTION
Thank you for selecting the Martin Cyclo. The Cyclo Series is a range of
controllable, fluorescent color changers. These fixtures are designed to be
used for cove lighting, perimeter lighting, light walls, behind semitransparent materials, or any place where room is restricted.
Cyclo is a family of fixtures based on dimmable fluorescent T5 tubes. The
T5 tubes have achieved widespread popularity due to their sleek design and
high efficacy combined with their long lamp life.
In order to be DMX controlled, the Cyclo fixtures require the Martin 516
DMX to 0-10 V Converter. The 516 Converter converts DMX to 0-10 V
analog output. Additional Cyclos can be daisy-chained for synchronous
dimming. A single 516 Controller can control 4-8 Cyclo groups individually,
each group consisting of one to ten of the same Cyclo model wired in series
(the number of groups depends on the model of Cyclo that is installed). The
member fixtures in each group will react similarly when controlled.
Cyclo control and power-cables are through-wired for easy installation.
The Cyclo series offers:
• Controllable RGB color-mixing and/or color temperature
• Bright output
• Long lamp life of 20,000 hours
Note:
It is important to read this manual through before you attempt
to install this product.
Cyclo fixtures
CYCLO 02
Cyclo 02 contains a single warm white tube and a single cold white tube.
It is designed as a functional lighting fixture for applications where dimmable
color temperature control ranging from 2700K up to 6000K are desirable.
CYCLO 03
Cyclo 03 contains dimmable red, green and blue tubes and is a cost efficient
RGB solution.
Cyclo user manual
3
C1
FLUORESCENT TUBES
Burning in new tubes
In order to obtain the full 20000 hour life time, new fluorescent tubes must
be burned in for 100 hundred hours at full power (10 volts).
I dentifying tube positi ons
Tube positions are identified in the Cyclo 03 and Cyclo 04 as follows:
Marking in fixture Marking on tube Color
R
OSRAM 28/60
Red
G
OSRAM 28/66
Green
B
OSRAM 28/67
Blue
None
OSRAM 28/827
OSRAM 28/840
OSRAM 28/860
2700K white
4000K white
6000K white
Reference illustration
R
G
B
CLEANING
We recommend that you clean the dust cover with a damp cloth.
C3,C4,C5
1 Dedicated to each C3 unit (2 total)
1 Dedicated to C4 units and C5 unit (1 total)
SV150T6 MH TOWER—METAL HALIDE ILLUMINATOR
9.5”
20”
NEW!
External Control for Color Wheel Tempo
There is now a dial on the outside of the
light source that easily allows the builder or
homeowner to increase or decrease the
amount of time spent on each color.
Screwdriver included.
REMOTE CONTROL
Remote Kit
Part No.: SVRFCK*
Description: remote
control for SV150T
- order separately
Model
Number
REPLACEMENT LAMP
FIBERHEAD UPGRADE
Replacement lamp
Part No.: 40-GA
756 Fiberhead Upgrade
Kit
Part No.: SVFH756KIT
Description
Ctn.
Qty.
Ctn.
Weight
Standard Units
4
SV150T1
White Light Only - remote control optional
SV150T6
6-Color: Moonlight white, hot pink, tangerine
dream, lime green, ocean deep blue, indigo blue
Synchronization Component
1
Replacement Lamp
40-GA
Replacement Lamp for 150 watt Metal
Halide Light Source
1
1/3 lb.
Wireless Remote Control - Optional. May be added to ANY tower style light source.
SVRFCK
SVRFT
SVRFR
Wireless remote control kit
Transmitter only
Receiver only
1
1
1
Upgrade Kit - Optional.
SVFH756KIT Kit increases light source capacity to
756 strands
TO ORDER 407.857.9900 or FAX ORDER FORM (PAGE 35) 407.857.0050
SPECIFICATIONS
Standard Units
UL Listed for Wet Locations
Electrical Rating:
• 120 VAC, 60 Hz / 3 Amps
(start up)
• 120 VAC, 60 Hz / 1.8 Amps
(running)
• 220-240 VAC, 50 Hz /
3.0 Amps (start up)
• 220-240 VAC, 60 Hz /
1.2 Amps (running)
Lamp:
• 150 watt metal halide - 4000K
• 10,000 hours average life
Fiber Capacity:
• 550 fibers maximum - PAF30
• 756 fibers max. upgrade
Power Consumption:
• 200 watts max.
Storage Temperature:
• -40°F to 140°F
• -40°C to 60°C
Ambient Operating Temperature:
• -20°F to 110°F
• -29°C to 44°C
Motors:
• 1RPM motor
Dimensions:
• 9.5 x 9.5 x 20”
• 241mm x 241mm x 508mm
Weight:
• 21 lbs.
• 9.5 kg.
Material/Finish:
• UV stabilized materials
• Water, corrosion and chemical
resistant
Mounting / Installation:
• Surface or burial mount
Ventilation:
• Forced ventilation 115 CFM,
FAN: 20 Watts, 80,000 life
hours. 6” clearance required
to nearest surface. 2’ clearance between each illuminator.
Warranty:
• 1 Year (excluding lamp)
• 550 strand capacity, upgradable
to 756 strands.
• Mounting pedestal base
included for clean installation.
• Easy lamp replacement.
• Taupe color blends easily with
the environment.
• On/off, start/stop switches on all
units.
• Hard wire ready for external
remote systems.
• Quick disconnects allow
Wireless Remote Control to be
added easily.
• Limited lifetime warranty on
lamp.
Synchronous Units
SV150T6C 6-Color: Moonlight white, hot pink, tangerine
dream, lime green, ocean deep blue, indigo blue
*Important! When adding wireless remote
to a synchronous system, one receiver (svRFR)
must be installed in each tower)
Note: 17.0609 Data cable must be installed between light sources.
Data Cable - 3 wire per foot
Features:
• Control amount of time spent on
each color.
• Slow, smooth transition from
one color to the next.
• Color Tempo dial located on
outside of light source.
• One unit can be either a
master or a slave unit when
synchronization is desired.
• May be used as a stand alone
unit in single light source
installation.
Synchronous Units for use with Multi-Illuminator Systems
17.0609
List
Price
SV150T Tower Illuminator
150 Watt Metal Halide lamp,
10,000 hour average lamp life,
550 strand fiber capacity
(upgradable to 756),
white light or 6-color,
mounting base included.
5 year limited warranty.
1
.6 lbs.
.4 lbs.
.4 lbs.
Features of Wireless
Remote Control
• Can be added to any metal
halide light source.
• Quick disconnects provide easy
installation.
C3, C4, C5
Leaders in Fibre Optic Lighting …
END LIGHT FIBRE OPTIC CABLE
Poly Optics is the leading manufacturer
of solid core plastic fibre optic cable for
lighting.
Our fibre is rugged, non-conductive,
water resistant and flexible.
The fibre is able to transmit light along
its length with minimal loss of intensity
and no heat transfer.
End Light Fibre is designed to be
illuminated with halogen or metal halide
light sources.
FOR USE IN A RANGE OF APPLICATIONS:
• Safety Lighting
• Decorative Lighting
• Inspection Lighting
Poly Optics Australia
1/18 Leda Drive
Burleigh, Q, 4220
Australia
• Non-Conductive Lighting
for Electricity-Free Areas
• Alternative Lighting
Ph: +61 7 5520 2222
Fax: + 61 7 5520 2255
www.fiberopticlight.com
C3,C4
UNDERWATER LENS
Original Polycarbonate Lens
Underwater Lens
Maximum fiber capacity: 300
Description: White, PVC housing
Applications: Pools, spas and fountains.
Flat Glass Lens - Flood
Multiple Lens application
Underwater Lens
Model No.
Description
Qty
Weight
1
1
1
1
.5 lbs
.5 lbs
.5 lbs
1 lbs
Original Polycarbonate Lens
SVG1
SVG1BLK
SVF1
SVV1
Gunite/white lens assembly
Gunite/black lens assembly
Fiberglass pools/white lens assembly
Vinyl pool/white lens assembly
Flat Glass - Flood
SVG1FLD
SVG1FLDBLK
SVF1FLD
SVV1FLD
Gunite/white lens assembly
Gunite/black lens assembly
Fiberglass pools/white lens assembly
Vinyl pool/white lens assembly
1
1
1
1
1 lbs
1 lbs
1 lbs
1.50 lbs
Convex Glass Lens - Spot
Single lens for pools
Convex Glass - Spot
SVG1SPOT
SVG1SPOTBLK
SVF1SPOT
SVV1SPOT
Gunite/white/white lens assembly
Gunite/black lens assembly
Fiberglass pools/white lens assembly
Vinyl pool/white lens assembly
1
1
1
1
1.25 lbs
1.25 lbs
1.25 lbs
1.50 lbs
SVLKEY2
Lens Key
1
.25 lbs.
3-9/16" 3-15/16"
Vinyl Lens
Lens Key fits all lenses
lens key
lens light
Features of glass Lenses
• Provides up to 30% more light transmission
fiber optic lens key
• Flat glass “flood” lens and convex “spot” lens
accommodate a variety of applications
• Sealed lens prevents water in the conduit, eliminating
problems such as clouding, algae growth, etc.
• 300 strand capacity
TO ORDER 407.857.9900 or FAX ORDER FORM (PAGE 35) 407.857.0050
C5
Leaders in Fibre Optic Lighting …
SIDE LIGHT FIBRE OPTIC CABLE
Poly Optics is the leading manufacturer
of solid core plastic fibre optic cable for
lighting.
Our fibre is rugged, non-conductive,
water resistant and flexible.
The fibre is able to transmit light along
its length with minimal loss of intensity
and no heat transfer.
Side Light Fibre is designed to be
illuminated with halogen or metal halide
light sources.
FOR USE IN A RANGE OF APPLICATIONS:
• Safety Lighting
• Decorative Lighting
• Inspection Lighting
Poly Optics Australia
1/18 Leda Drive
Burleigh, Q, 4220
Australia
• Non-Conductive Lighting
for Electricity-Free Areas
• Alternative Lighting
Ph: +61 7 5520 2222
Fax: + 61 7 5520 2255
www.fiberopticlight.com
FC1, FC2
Cove by others
COVELIGHT 26
Cove by others
FCV 26
Low-profile cove mounted
2” x 6” luminaire with indirect
asymmetric distribution.
1 Lamp T8
1 Lamp T5 & T5HO
2 Lamp T5 & T5HO
Features
March 2005
Construction
Electrical
Emergency
One piece housing of die-formed
22 Ga. C.R.S. forming 2”H x 6”W
rectangular profile. Socket bridge
and 20 Ga. Galvanized end caps
are mechanically fastened.
Luminaires are pre–wired with
factory installed branch circuit
wiring with over-molded quick
connects. All ballasts are thermally
protected and have a Class “P”
rating.
Emergency battery packs provide
90 minutes of one lamp
illumination. Initial lumen output
for lamp types are as follows:
Weight:
4’ unit—7 lbs
8’ unit—14 lbs
Optic
Die–formed 20 Ga. steel reflector
with aluminum insert, finished in
high reflectance white paint
(90% reflectance).
Consult Ballast Ordering Guide on
following page for ballast
specifications
Optional DALI and other dimming
ballasts available. Consult factory
for specifications and availability.
UL and cUL listed.
T8 Lamp:
Up to 550 lumens
T5 Lamp:
Up to 550 lumens
T5HO Lamp: Up to 825 lumens
Battery pack requires unswitched
hot from same branch circuit as
AC ballast.
Finish
Luminaire housing and reflector
are finished in high reflectance
white paint (90% reflectance).
6.00"
152.4mm
2.00"
50.8mm
Cove by others
• High performance indirect luminaire
designed for concealed cove
applications.
• Covelight provides pleasing and
even illumination that highlights
architectural details.
• Continuous row installations may be
configured with 2', 3', 4’, 5', 6', 7’ and
8’ luminaires.
• Metric housing design for T5/T5HO
lamps minimizes socket shadows.
• Enhanced ease of installation: simple
plug connection eliminates need to
access electrical components in luminaire housing.
SPECIFIER GUIDE
UL
R
FC3
PRODUCT
DESCRIPTION
LISTED
PRODUCT
C O D E
CURVABLE COMPACT FLUORESCENT STRIPLIGHT
CHANNELITE UBL 5000 BX0X
DRAWING NO. CL 404
C COPYRIGHT 2004
UBL 5000 BXOX
• Ideal for indirect lighting in curved spaces
• Overlapping lamps for shadow-free light at close
distances from illuminated surface
• Uses long, high-output lamps for
OVERLAPPED
maximum lumens per ballast
COMPACT
• Listed for damp location
FLUORESCENT LAMP
• 10% dimming with standard
dimming ballasts (consult factory
for 5% dimming)
1/2 “ CONDUIT
(BY CONTRACTOR)
FLEXIBLE
JOINER
END VIEW
UBL 20
KNOCK OUT
END CAP
SEE BELOW FOR
LAMP SPACING
4 1/2”
2”
SPECIFY TOTAL
LENGTH OF RUN
BALLAST
SEE BELOW FOR
MINIMUM INSIDE RADIUS
3 1/4”
2” X 3 1/4 “
ALUMINUM HOUSING
UBL 19
BLANK
END CAP
LAMP SELECTION
TYPE
: COMPACT FLUORESCENT
BRANDS : GE “HIGH LUMEN BIAX,” PHILIPS “PL-L,” OSRAM “DULUX-L”
WATTS LENGTH
18W
10.5”
27W/24W
12.8”
39W/36W
16.5”
40W/38W
22.5”
50W
22.5”
BASE
RATED HRS. LUMENS
2G11 12000-20000 1160-1250
12000
2G11
1800
12000
2G11
2850-2900
20000
2G11
2900-3300
14000
2G11
4000-4300
Refer to manufacturers’ catalog for full selection and details.
COLOR TEMP.
3000-6500
3000-4100
3000-4100
3000-5000
3000-4100
CRI
82
82
82
82
82
QUICK REFERENCE INSTALLATION INSTRUCTIONS
1. Remove cover piece from module, by removing screws and using
flathead screwdriver to pry open.
2. Screw mount bottom piece directly onto secure surface.
3. Snap cover piece into bottom piece and replace screws.
4. To continue run, attach and mount next module and make electrical
connections.
5. Attach end caps at beginning and end of run, sliding base plate
into bottom piece and securing with screw.
6. Connect lead wires at beginning of run to power source and
ground. Do not power until installation complete.
7. Insert lamps.
COVER
BOTTOM
END CAP
BASE PLATE
LAMPS NOT INCLUDED
SS PP EE CC II FF II CC AA TT II OO NN SS
UBL 5000 BXOX
BALLAST
LOCATION
LAMP WATTAGE & SPACING
PRODUCT CODE
18W
9 ” on center (21” minimum inside radius)
I
Integral
BALLAST
TYPE
ELE Electronic
27W / 24W 11” on center (25” minimum inside radius)
DIMMING
VOLTS
FINISH
ND Non-dimming
120 V
NAL Natural aluminum
DM Dimming*
277 V
SAT Anodized satin
WHT High reflectance
white powder
coat
39W / 36W 15” on center (34” minimum inside radius)
40W
20” on center (46” minimum inside radius)
50W
20” on center (46” minimum inside radius)
*Available for
36W thru 50W
Or specify other
EXAMPLE
UBL 5000 BXOX
40 W
20” o.c.
I
ELE
ND
120V
NAL
FILL OUT BELOW FOR SUBMITTAL
UBL 5000 BXOX
I
ELE
PROJECT
NAME
SPECIFIER
FIXTURE
SCHED. TYPE
CONTRACTOR
QUANTITY
DISTRIBUTOR
LENGTHS
REPRESENTATIVE
visit us at :
w w w. c e l e s t i a l l i g h t i n g . c o m
e•mail :
info @ celestiallighting.com
14009 Dinard Ave.
Santa Fe Springs,
CA 90670
PH (562)•802•8811
(800)•233•3563
FX (562)•802•2882
FD1, FD4
Type
FEATURES
OPTICAL SYSTEM
• Reflector - Self-flanged, specular clear or semi-diffuse
reflector. Fluted vertical upper section works in conjunction with Bounding Ray Optical Principle to provide lamp
before lamp image and smooth transition from top of reflector to bottom. Minimum flange matches reflector finish. White painted flange optional.
• Baffle/cone - Specular clear upper reflector. Microgroove
baffle with white painted flange or specular black cone
with flange that matches cone finish.
• Hinged lampdoor seals upper trim for optimal fixture efficiency and the reduction of stray light in the plenum.
MECHANICAL
• 16-gauge galvanized steel mounting/plaster frame with
integral yoke to retain optical system. Maximum 1-1/2"
ceiling thickness.
• Mounting bars are 16-gauge galvanized steel with continuous 4" vertical adjustment, held in place with toolless, integral cam-action locking system. Post installation
adjustment possible without the use of tools from above
or below the ceiling. Shipped pre-installed.
• Galvanized steel junction box with bottom-hinged
access covers and spring latches. Two combination 1/2"–
3/4" and three 1/2" knockouts for straight-through conduit
runs. Capacity: 8 (4 in, 4 out) No. 12 AWG conductors,
rated for 90°C.
ELECTRICAL SYSTEM
• Horizontally-mounted, four-pin, positive-latch, thermoplastic socket.
• Class P, thermally-protected high power factor electronic
ballast mounted to the junction box (CP and EL ballast
mounted on ballast tray).
LISTING
• Fixtures are UL listed for thru-branch wiring, recessed
mounting and damp locations. Listed and labeled to comply with Canadian Standards (see Options).
Catalog number
.....................................
............................................................................................................................................
.....................................
............................................................................................................................................
Compact Fluorescent Downlights
6" AF
Open Reflector
Horizontal Lamp
Triple-Tube
7-1/4 (18.4)
Aperture: 6-1/4 (15.9)
Ceiling Opening: 7-1/8 (18.1)
Overlap Trim: 7-1/2 (19.1)
15-7/8 (40.3)
ENERGY
LER.DOL
41
Annual
Energy Cost
$5.83
Lamps
1/26TRT
Lamp
Lumens
1800
Ballast
Factor
0.98
13-5/8
(34.6)
Input
Watts
27
All dimensions are inches (centimeters).
Calculated in accordance with NEMA standard LE-5.
Example: AF 1/26TRT 6AR MVOLT
ORDERING INFORMATION
Choose the boldface catalog nomenclature that best suits your needs and write it on
the appropriate line. Order accessories as separate catalog number (shipped separately).
AF
Series
AF
Wattage/Lamp
Reflector/Color
1/18TRT
6AR
1/26TRT
6PR
1/32TRT
6UBR
1/42TRT
6WTR
6CR
6GR
6MB
6BC
Clear
(blank) Specular low
iridescent
Pewter
LD
Semi-diffuse
Umber
low
Wheat
iridescent
Champagne
1
Gold
Gold 1
Black Baffle2,3
Black Cone2
NOTES:
1 Not recommended for use with compact fluorescent lamp.
Consult factory.
2 Not available with finishes.
3 White flange standard.
4 Multi-volt electronic ballast capable of operating on any
line voltage between 120-277 volt.
5 Consult factory for specific availability.
6 Not available with black cone.
Ballast
Voltage
Finish
MVOLT
4
120
277
347
Options
(blank) GEB10 standard.
Electronic ballast.
5
DMHL
Lutron Hi-Lume
electronic dimming ballast
5
ADEZ
Advance Mark X
electronic dimming ballast.
WLP
TRW
6
EL
ELR
GMF
RIF
LRC
Accessories
Order as separate catalog number.
SC6FL
Sloped ceiling adaptor.
Degree of slope must be
specified (10D, 15D, 20D,
25D, 30D). Ex: SC6FL 10D
QDS
CP
CSA
With 35°K lamp (shipped
separately).
White flange.
Emergency battery pack.
Integral test switch provided.
Emergency battery pack.
Remote test switch provided.
Single, slow-blow fuse (not
available with MVOLT).
Radio Interference Filter.
Provides compatibility with
Lithonia Reloc System. Reloc
System can be installed less
this option with connectors
provided by others. Access
above ceiling required. For
compatible Reloc Systems, see
options and accessories tab.
Quick Disconnect for easy
ballast replacement. Not
available with EL or ELR option.
Chicago Plenum (consult
factory).
CSA Certified.
AF 6 TRT OPEN
DCF-110
FD2
Calculite® Compact Fluorescent Open Downlight
Page 1 of 2
8037
7 3/8” Triple Tube Horizontal Lamp
2
5
15"
(381 mm)
7 3/4"
(197 mm)
5 3/4"
(146 mm)
11 3/8"
(289 mm)
1
3"
(76 mm)
12"
(318 mm)
6
Top View
1" (25 mm) min.2 1/8" (54 mm) max.
(Ceiling Runner)
7 3/8" (187 mm) Dia.
4
7 7/8" Trimless
(200 mm)
3
8 5/8" Self-Flanged Trim
(209 mm)
1 1/8" (29 mm) max.
Ceiling Thickness
Ceiling Cutout: 8” (203 mm) Dia.
Reflector Trim
Frame-In Kit
8037CLW
8037CLP
8037CL
8037
7132BU
7132BCU
Electronic
PowerSpec® Dimming
120V - 277V
120V - 277V
26 or 32W Triple Tube
4-Pin (Amalgam)
7142BU
7142BCU
Electronic
PowerSpec® Dimming
120V - 277V
120V - 277V
42W Triple Tube
4-Pin (Amalgam)
Clear Iridescence Free, White Flange
Clear Iridescence Free, Polished Flange
Clear Iridescence Free, Molded Trim Ring
Add suffix. See options for other finishes.
Lamp
Remodeler Frame-In Kit
7132BURM
7142BURM
Electronic
Electronic
Lamp
120V - 277V
120V - 277V
Same as 7132BU
Same as 7142BU
Features
Options and Accessories (continued)
1. Reflector: 16 ga. Alzak® aluminum, 55° visual cutoff to lamp and lamp
image, wide distribution. Iridescence Free finish. Self-flanged or flangeless
with molded white trim ring (field paintable).
2. Socket Cup: Die-cast aluminum cup effectively dissipates heat and positions lamp holder. Snaps onto reflector neck to assure consistently correct
optical alignment without tools.
3. Mounting Frame: Die-cast aluminum for dry or plaster ceilings.
4. Retaining Springs: Precision-tooled steel friction springs secure reflector
to mounting frame for quick, tool-less installation.
5. Mounting Brackets: 16 ga. steel. Adjust from inside of fixture. Use 3/4” or
1 1/2” lathing channel, 1/2” EMT, or optional mounting bars.
6. Ballast/J-Box: Outboard mounted to reduce heat transfer and maintain
lamp efficacy and life. Service from below without tools.
Emergency
Chicago Plenum
Existing/Thk. Ceiling
Emergency Ltg. Kit
Electrical
Note: For ballast electrical data and latest lamp/ballast compatibility refer to
“Ballast” specification sheet for complete electrical data.
7132BU, 7132BCU, 7142BU, 7142BCU: UL listed for through branch circuit
wiring with max of (8) No. 12 AWG, 90°C supply conductors.
7132BURM, 7142BURM: UL listed for No. 12 AWG, 90°C supply conductors.
Options and Accessories
Comfort Clear™ Finishes1
Clear
CCL
Diffuse
CCD
Champagne Bronze
CCZ
Pewter
CPW
Specify desired flange
W White, P Polished
Blank - Molded Ring
Other Finishes
White
Multigroove
Add suffix EM*
Add suffix LC
FA EC7*
FA EM3E*
FA EM4E*
Fuse (Slow Blow)
Add Suffix F
*See Spec. Sheets: FAEC, FAEM
Mounting Bars & Accessories; see Specification Sheet MBA.
Sloped Ceiling Adapters; see Specification Sheet SCA.
Labels
UL listed for damp locations, I.B.E.W.
Alzak® is a registered trademark of ALCOA.
US Patent Pending.
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
WH
MG
Notes:
1
Lightolier a Genlyte Thomas Company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2002 Genlyte Thomas Group LLC (Lightolier Division) • A0902
FD3
DELRAY
6" SEMI RECESSED DOWNLIGHT
0000000
0000
LIGHTING
0000
000
0
00000000
INCORPORATED
7"
6.75"
12.75" X 7.75"
SPECIFICATION INFORMATION
HOUSING ASSEMBLY
BALLAST
Mounting Frame and J-box are
galvanized, pre-coated steel.
Telescopic bar hangers are
supplied and provide for off center
mounting. Socket has twist lock
mechanism for re-lamping with a
pole. Can is spun aluminum with
self flange trim, finish is matte
white powder coat. Fixture is
prewired with ground wire
included.
Electronic ballasts use 4 pin lamps
and provide rapid start .99 power
factor with THD<10%. Standard
ballast operates 26, 32 or 42W
lamps. Outboard mounting
provides quiet cool operation.
Dimming ballast controls lumen
output down to +- 5% . All require
compatible dimmers.
GLASS
The glass is hand blown and
available in four colors, glass color
must be specified.
I - indigo
M - marine
O - opal
T - tangerine
ELECTRICAL
ACCESSORIES
CHANGER for re-lamp pole
D1 Lutron Hi-Lume dimming
ballast (specify wattage)
4740
3.5"
D3 Advance Mark X dimming
ballast (specify wattage)
D4 Lutron Tu-Wire dimming
ballast 120V only(specify wattage)
EM emergency power pack ignites
one lamp for 90 minutes with
remote charge indicator light
Allows 4-in / 4-out #12 AWG
conductors rated at minimum
90° C. For use in damp locations.
J-box and ballast are accessible
through fixture. U.L. Listed for use
in damp locations.
ORDERING INFORMATION
LAMP
1-26 26 watt triple tube
1-32 32 watt triple tube
1-42 42 watt triple tube
120V ELECTRONIC
4740.I.1 120V indigo
4740.M.1 120V marine
4740.O.1 120V opal
4740.T.1 120V tangerine
277V ELECTRONIC
4740.I.2 277V indigo
4740.M.2 277V marine
4740.O.2 277V opal
4740.T.2 277V tangerine
11916
VALERIO ST.
NORTH
HOLLYWOOD,
CALIFORNIA
91605
SUBMITTAL INFORMATION
TYPE:
DESCRIPTION:
PROJECT:
PHONE
NOTES:
818 982 3701
FAX
818 982 3715
FD5, FD5b
Type
FEATURES
OPTICAL SYSTEM
• Semi-specular clear anodized aluminum upper
reflector.
• Available with tempered prismatic lens (T73), flat
fresnel lens (FFL), concave Holophane lens (CHL),
polycarbonate clear lens (PCL), prismatic polycarbonate lens (PPC), acrylic prismatic lens ([email protected]),
acrylic clear lens (CAL) or flat opal (acrylic) lens
(FOL).
DOOR
• Regressed white splay or stepped matte black
baffle lens door frame.
• Self-aligning butterfly door support springs.
MECHANICAL SYSTEM
• 16-gauge galvanized steel mounting/plaster frame
accommodates up to 1-1/4" thick ceiling standard.
• Mounting bars are 16-gauge galvanized steel with
continuous 4" vertical adjustment, held in place
with tool-less, integral cam-action locking. Post
installation adjustment possible without the use
of tools from above or below the ceiling. Shipped
pre-installed.
• Galvanized steel junction box with bottom-hinged
access covers and spring latches. Two combination 1/2"-3/4" knockouts and three 1/2" knockouts for straight-through conduit runs. Capacity:
8 (4 in, 4 out) No. 12 AWG conductors rated for
90oC.
ELECTRICAL SYSTEM
• Die-cast aluminum socket housing. Ventilated top
for effective heat dissipation.
• Vertically-mounted, positive latch thermoplastic
sockets.
• Class P, thermally-protected, high power factor
ballasts mounted to the junction box.
LISTING
• Fixtures are UL listed for thru-branch wiring, recessed mounting and wet locations. Listed and
labeled to comply with Canadian Standards.
Catalog number
...................................
.............................................................................................................................................
...................................
.............................................................................................................................................
Compact Fluorescent Downlights
7" LGFV
Round Lens
Wet Location
Vertical Lamp
Tri-Tube
10-1/8 (25.7)
Aperture:
Ceiling opening:
Overlap trim:
7-1/8 (18.1)
8-1/8 (20.6)
8-5/8 (21.9)
13-1/8 (33.3)
14-1/2
(36.8)
All dimensions are inches (centimeters).
Example:
ORDERING INFORMATION
LGFV 26TRT 7RW T73 120
Choose the boldface catalog nomenclature that best suits your needs and write it on
the appropriate line. Order accessories as separate catalog numbers (shipped
separately).
LGFV
Series
LGFV
Wattage/lamp
26TRT
32TRT
42TRT
1
One 26W tri-tube
One 32W tri-tube
One 42W tri-tube
Door frame
7RW
7SB
7FW
Accessories
Order as separate catalog number.
SC7
Sloped ceiling adaptor. Degree of
slope must be specified (10D, 15D, 20D,
25D, 30D). Ex: SC7 10D.
Regressed
white
door
Stepped
black
baffle
Flush
white
door
Shielding
T73
2
CHL
FFL
Prismatic
lens
Concave
Holophane
lens
Flat fresnel
lens
Voltage
Options
120
LP
277
SSC
347
Notes:
1 Operates Philips PL-T or Osram
Dulux T/E type lamp.
2 Not available with 42TRT.
3 Hi-lume is a registered trademark
of Lutron Electronics.
GMF
RIF
DMHL
ELR
TPS
CSA
With 30K lamp (shipped separately).
Provides compatibility with Lithonia Reloc System
820. System 820 can be installed less this option
with connectors provided by others.
Single slow-blow fuse.
Radio interference filter.
Lutron Hi-lume3 electronic dimming ballast, 120V or
277V, 32W only.
Emergency battery pack. Remote test switch provided. (Consult factory for dimensional changes.)
Tamperproof. (Includes two tamperproof screws.
Not available with flush white door frame.)
Listed and labeled to comply with Canadian Standards.
LGV 7
DCF-530
FP1, FP2
Architectural Decorative Soli Zontio
48228ALU
Page 1 of 3
2 Light, T-5 Pendant
22 3/8"
4"
1
(568)
(102)
7
2"
(51)
6
2
4
5
20 3/4" (527)
26 3/4" (679.5)
32 3/4" (832)
8
3
6 13/16"
6 7/8"
(173)
(175)
1 3/4"
47 1/2"
(44.5)
(1206.5)
1"
(25)
42 7/8"
9"
(229)
40800
42 7/8"
8 1/4"
(1089)
40810
(210)
(1089)
Diffuser Curved Glass
Diffuser Flat Glass
Note: Luminaire can be ordered with or without diffuser shield. Order each separately.
( ) Denotes dimensions in mm
Fixture Ordering Information
Catalog No.
Finish
Wattage
Voltage
Lamping
48228ALU
48254ALU
Metallic Aluminum Powder Coated
Metallic Aluminum Powder Coated
2 x 28W
2 x 54W
120/277V
120/277V
T-5, Mini-Bipin
T-5 HO, Mini-Bipin High Output
Diffuser Ordering Information (Order diffuser separately)
Catalog No.
Description
Dimensions
Finish
40800
40810
Flat Glass Diffuser (3/"8 Thick)
Curved Glass Diffuser (3/8" Thick)
9" W x 42 7/8" L
8 1/4" W x 42 7/8" L
White ceramic coated top, etched bottom. Clear polished edges.
Etched top and bottom. Clear polished edges.
Features
Options
1. Mounting Plate: 18 GA. (.048) Galvanized steel for direct mounting to
most junction boxes. Secondary mounting holes provided to mount directly
to ceiling.
2. End Cap: (2) Die cast aluminum. See above for finish.
3. End Cover: (2) Die cast aluminum. See above for finish.
4. Lamp Enclosure: (2) Extruded aluminum. See above for finish.
5. Support Stem: (2) 3/8" diameter steel tubing. Luminaire provided with three
lengths (10", 16" and 22"). See above for overall heights. Stems can not be
added together.
6. Swivel: (2) Meets California Earthquake codes.
7. Housing: Extruded aluminum. See above for finish.
8. Ballast: See below for details.
Dimming: (Voltage Specific/54W HO lamps)
Add MX1 suffix code (for 120V) to Cat. No.
Add MX2 suffix code (for 277V) to Cat. No.
example: 48254ALMX1
Emergency: Integral Bodine LP550 emergency battery pack, test switch and
light, add E suffix code to Cat. No.
DALI: Digital Dimming System ballast 120/277V. Add DA suffix code to Cat. No.
Labels
cULus Listed. Suitable for Damp Locations
Job Information
Lamping (by others)
Job Name:
Linear Fluorescent: 28W T5 or 54W T5 HO, Mini Bipin
Cat. No.:
Electrical
Lampholders: G5 (Mini-Bipin) base with rotor for securing lamp. cULus Listed.
Ballast: Electronic, HPF, Universal voltage 120V-277V.
Voltage
Total Input Watts
Max. Line Current (Amps)
Ballast Factor
Min. Starting Temp: 0°F/-18°C
THD<10%
28 Watt
120V
277V
64
63
0.55
0.23
1.03
1.03
54 Watt
120V
277V
120
117
1.0
0.43
1.0
1.0
Type:
Lamp(s):
Notes:
Lightolier a Genlyte company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2004 Genlyte Group LLC • A0904
FP3
American Glass Light Product Spec Sheet:
Fixture Name: Harrington Uplight
Catalog #: 2746-U
Selected Width: 30"
Selected Height: 36"
Selected Lamping: (4) 42W Triple Tube Compact Fluorescent
Selected Glass/Panel: White Sandblasted Glass
Selected Finish: Polished brass (std.)
Additional Details: Weight for standard lamping 24" width: 10 Lbs. Weight for standard lamping 30" width: 24
Lbs. Weight for standard lamping 48" width: 51 Lbs. Please contact us for lamp specification and ballast remoting
information. Metal halide lamping requires remote ballast. Extension Option Available. Dimensions, finishes,and
lamping ship standard as listed unless special order options are requested.
120 volts is standard unless other voltage is ordered.
Your Notes:
When specifying this product, please indicate all selected options so we have complete information when
an order is placed.
A
B
C
D
E
F
H
D
K
J
1-1/2"
(38mm)
1:10 Scale
Sightline
D
O
Max.
Candlepower
Varies
* For cove design guidance,
see Applications Section
Patent pending
H
A
C
G
B
D
T5 Fluorescent
Pendant Hanger
18"
min.
up to
48"
max.
x
x
x
x
x
x
2'
3'
4'
5'
3'
4'
Length
Lamp
(center to
Length center of hubs)
25-1/4" (640mm)
37" (940mm)
48-3/4" (1240mm)
60-5/8" (1540mm)
72" (1830mm)
96" (2440mm)
1
1
1
1
2
2
K Tubular steel arm or stem
L Aluminum mounting plate
M Access with gasketed
cover (electrical feed)
N Recessed outlet box
O 1/2" fittings (by others)
Electrical:
Use 90°C wire for supply connections and through wire.
Electrical feed hanger (optional) mounts over recessed outlet
box (by others) with gasketed access cover. Internal wireway
allows supply wiring to be fed through mounting hub to
adjacent units. Locate electrical feed at end of row.
Integral electronic HPF thermally protected class P ballast
rated for 0°F/-18°C starting.
For complete ballast specifications, see Accessories Section.
Standard:
UL listed or CSA certified for wet locations when mounted
horizontally. For positions other than horizontal,
consult factory.
G Specular extruded
aluminum reflector
H Surface or pendant
hangers with hubs
(ordered separately)
Aluminum cover
(conceals fasteners)
J
Varies,
3-1/2"
min.
12"
min.
(305
mm)
Cove*
Length (see chart)
N
M
L
Mounting Plate
4-3/4"
(121
mm)
3-1/4"
(83mm)
D Aluminum hubs with
silicone o-ring gaskets
(ordered separately)
E Integral electronic
ballast / internal wireway
1/2" rigid conduit
supports (by others)
F
Medium outdoor, integral
1:8 Scale
Uplighting
Style F164
6"
(152mm)
7-9/16"
(192mm)
Surface Hanger
6"
(152mm)
x
4-1/2"
(114mm)
Specifications
A UV and impact resistant
acrylic snap-on lens
with silicone gasket
B Die-cast aluminum
end plates
C Extruded aluminum visor
with stamped end plates
Finish:
Exterior surfaces - 6 stage pretreatment and electrostatically
applied thermoset polyester powder coating for a durable
abrasion, fade and corrosion resistant finish. Choice of
semi-gloss colors (see ordering information).
Reflector - extruded high purity aluminum with clear anodized
specular finish. All hardware and components - non corrosive
stainless steel or aluminum.
Snap-on lens - composite of impact resistant and UV
stabilized acrylic. Silicone gasket for watertight operation.
Mounting:
1-1/2" dia. x 1-1/2" aluminum hubs with 1/2" NPT threaded
entry. Reflector aiming is adjustable - locks with set screws.
Specify with hubs only for use with 1/2" rigid conduit or fittings
supplied by others, or specify accessory surface or pendant
hangers (ordered separately). Hangers include aluminum
mounting plate, cover and hub with 7/8" O.D. steel arm/stem
(1/4-20 fasteners by others). Suitable backing structure
required - allow 3 lbs/ft (21.6kg/m) (8' unit = 24 lbs).
Specify end kit or intermediate hubs/hangers.
6/04
Features
Style 164
with unequaled uniformity from minimal setbacks
■ Reflector optimized for T5 - uplight canopies, vaults, soffits
■ Secure snap-on UV resistant acrylic lens - easy to relamp
■ Extruded visor provides shielding - concealed drainage
■ Polyester powder coat - exceeds 1000 hour salt spray test
2500
Cd
1x
55W
■ Integral electronic ballast - internal wireway for thru wiring
Performance
Two parabolic reflector
sections drive light
across the overhead
plane from one edge.
An elliptical section
redirects its light to a
parabola and shields the
lamp. Asymmetry is
maximized resulting in
high beam efficiency
and superior surface
uniformity. The fast
"runback" minimizes
wasted spill light.
Adjustable max. Cd
shown
aimed 25°
above
horizontal.
For complete photometrics, visit www.elliptipar.com
Note: Lamp light output may
be diminished when operated
in low ambient temperatures.
elliptipar
FP4
U
2.2
U
2.3
To Order
2
3
4
-H -
To form a Catalog Number
1
F 1 6 4 -T
1 Source
F = Linear fluorescent
2 Style
5
-
= T5 Fluorescent Lamp Code
164 = Medium outdoor, integral ballast
3 Lamp
T
6
Lamp Wattage (see chart below)
Number of Lamps in Length, specify 1 or 2
Lamp Length
(nominal)
T114
T121
T128
T135
T221
T228
Code
7
-V
Code
T5HO
Lamp(s)
8
F24T5/HO
F39T5/HO
F55T5/HO
F80T5/HO
F39T5/HO
F55T5/HO
T5
Lamp(s)
x
x
x
x
x
x
1
1
1
1
2
2
x
x
x
x
x
x
T124
T139
T155
T180
T239
T255
1
1
1
1
2
2
F14T5
F21T5
F28T5
F35T5
F21T5
F28T5
Example: T155 = Nominal 4' (1.2m) housing with one 55W
T5HO lamp
T5 Fluorescent
2'
3'
4'
5'
6'
8'
For complete lamp and ballast information, see Accessories
Section. Standard T5 lamp color is 3000K / 80+ CRI.
4 Mounting
elliptipar
elliptipar
H = For use with mounting hubs (1/2" rigid conduit supports
or fittings supplied by others), or
For use with accessory surface or pendant hangers.
Note: Order either hubs only or hubs with hangers separately.
For reflector positions other than horizontal,
consult factory.
6/04
Project:
=
=
=
=
=
Semi-gloss white
Dark bronze
Silver
Semi-gloss black
Green
5 Finish
02
06
07
08
12
6 Voltage/Ballast
Electronic
1 = 120V*
2 = 277V
3 = 347V
99 = Custom RAL or
computer matched
color to be specified,
consult sales
representative.
* Dimmable ballasts available for F55T5/HO only. Consult sales representative.
7 Option
V0 = Cutoff visor included, no other option
00 = Cutoff visor NOT included, no other options
(Suggested when architectural cove or other detail
provides shielding of lens brightness.)
VX = For modification not listed, include detailed description.
Consult factory prior to specification.
8 Standard
0 = UL, Underwriters Laboratories
J = CSA, Canadian Standards Association
Example
F164 - T155 - H - 08 - 1 - V00
■
Medium outdoor fluorescent for use with one 55W T5HO
lamp in nominal 4 foot reflector. For use with mounting hubs
(1/2" rigid conduit supports by others) or accessory hangers.
Semi-gloss black powder coat finish. Integral 1-lamp 120V
electronic ballast. Cutoff visor included. UL.
(Order end kit and intermediate mounting hubs or
hangers separately.)
■
elliptipar
114 Boston Post Road, West Haven, Connecticut 06516, USA
Voice 203.931.4455 Fax 203.931.4464 www.elliptipar.com
Type:
Hubs Only
5
5
(order separately)
Style 164
(order separately)
000 = Intermediate
mounting hub
000 = End kit
(includes 2
mounting hubs)
For use with 1/2" rigid conduit or fittings (supplied by others).
Order one hub end kit for each individually mounted luminaire
or each row. For a continuous row, order one intermediate
hub for each additional luminaire in the row. Example: a row
of six reflectors requires 1 hub end kit and 5 intermediate
hubs. Note: Locate electrical feed at end of row.
HOD
HOC
Hubs with Hangers
= Outdoor pendant hanger
= Outdoor surface hanger
0 = UL
J = CSA
5 Finish
A = Intermediate
B = End kit
00
Order one hanger end kit for each individually mounted
luminaire or each row. For a continuous row, order one
intermediate hanger for each additional luminaire in the row.
Example: three rows of four reflectors requires 3 end kits and
9 intermediate hangers. Note: Hubs included. End kit
includes one electrical feed hanger - locate at end of row.
HB
HB
0 = UL
J = CSA
Length,
in inches,
specify 18,
24, 30, 36,
42 or 48
5 Finish
F = Intermediate
G = End kit
The external shapes of the asymmetric reflectors are trademarks of elliptipar.
Certain products illustrated may be covered by applicable patents and patents pending.
For a list of patents, see Contents pages. These specifications supersede all prior
publications and are subject to change without notice. ©2004 elliptipar.
FP4
FS1
Catalog Number
Notes
Type
FEATURES & SPECIFICATIONS
INTENDED USE
T5 linear direct fluorescent intended for use in low-profile commercial,
retail, manufacturing, warehouse, cove and display applications.
ATTRIBUTES
Designed exclusively for use with T5 lamps, T5 sockets and T5 electronic ballasts.
CONSTRUCTION
Housing formed from cold-rolled steel. No asbestos is used in this product.
Heavy-duty 20-gauge channel.
Extended-height end caps retain and support sockets. Compact T5 socket features rotating collar and enclosed contacts.
FINISH
High-gloss, baked white enamel finish. Five-stage iron-phosphate pretreatment
ensures superior paint adhesion and rust resistance.
OPTICAL SYSTEM
A variety of optical assemblies are available. See the MS5-Reflector or
MS5-Louver spec sheets.
ELECTRICAL SYSTEM
Thermally protected, resetting, Class P, HPF, non-PCB, UL Listed.
Suitable for damp locations. AWM, TFN or THHN wire used throughout, rated for
required temperatures.
INSTALLATION
Labor-saving coupler supplied for row mounting. Numerous knockouts for easy
installation. Surface-mount or suspended.
LISTING
UL Listed and CSA Certified (see Options).
WARRANTY
Guaranteed for one year against mechanical defects in manufacture.
Low-Profile T5 Direct
Channel
MS5
2', 3', 4' or 8' Lengths
1 or 2 Lamps
Specifications
Length: 22-7/16 (569), 34-1/4 (869),
46-1/16 (1169) or 92-1/16 (2337)
Width: 2 (51)
Depth: 2-1/4 (57)
Weight: 4.8 lbs (2.2 kg)
Specifications subject to change without notice.
ORDERING INFORMATION
Example: MS5 1 54T5HO MVOLT GEB10PS
MS5
Series
MS5 T5 low-profile
direct
Number
of lamps
1, 2
Not included.
For tandem
double-length
unit, add
prefix T.1
Example:
TMS5
Lamp type
14T5
21T5
24T5HO
28T5
39T5HO
54T5HO
14W T5 (22")
21W T5 (34")
24W T5 HO (22")
28W T5 (46")
39W T5 HO (34")
54W T5 HO (46")
Voltage
Options
347 ,
MVOLT3
G E B 1 0 P S Electronic ballast, <10% THD,
Program Start
GLR Internal fast-blow fuse4
GMF Internal slow-blow fuse4
PLF_ Plug-in wiring, specify 1, 2 or 3
branch circuits and hot wires
(A=black, B=red, C=blue, AB or AC)
E L 5 5 Emergency battery pack
(nominal 390-700 lumens; see
Fluorescent Battery Packs
tab) 1, 4
C S A CSA Certified
2
Others
available.
Accessories
Order as separate catalog number.
WGMS5Z
THMS5
1B
SQ_
Wireguard, 4', zinc
Tong hanger
Ceiling spacer (adjusts from 1-1/2" to 2-1/2" from ceiling)
Swivel stem hanger (specify length in 2" increments)
Fluorescent
NOTES:
1 Only available with 28W and 54W.
2 Only available with 54W.
3 Available with GEB10PS only.
4 Specify voltage.
Sheet #: MS5
10-60
FT1
SKY
Specification Grade
Deep Regressed
Lens Troffer
Type: ________________________________________________
Job Description: _______________________________________
Available in a wide assortment of sizes
Features
• Deep regressed trim without a surrounding black reveal
enables the fixture to imitate a natural skylight.
• Extruded aluminum white trim presents a clean highly
gloss finish.
Ceiling Compatibility
• Available in an assortment of sizes.
Type G
For lay-in installation in exposed grid ceilings. Maximum tee widths of 1″ and
maximum tee heights of 11⁄ 2″
allowed.
• Standard white opal lens produces a luminaire with a true
skylight appearance.
• Available with a wide assortment of lamps.
• Optional trim finishes available to match ceiling tiles.
• Lay-in lens ensures lens security with ease of removal.
• Designed to fit NEMA type G, F and M ceilings.
• 8″ deep housing ensures no lamp imaging which retains the
skylight appearance.
19⁄ 16″
Housing
Fixture is constructed of die formed and embossed code gauge
steel. End caps are riveted to the housing for added rigidity.
Designed for installation in all ceilings as shown below. Specify
exact ceiling type.
Type F
Ballast & Electrical
Overlapping extruded aluminum trim conceals edges of
ceiling opening. Cantilever
arm suspension system included. For in-row mounting,
row information is required.
23⁄ 4″
1 ⁄ 16″
9
All luminaires are completely wired with class “P”, thermally
protected, resetting, HPF, CBM, LE ballast, sound rated A.
Lampholders are medium bi-pin with positive retention and
edge-wipe contacts. Furnished with an access plate.
Finish
All metal parts processed with a five-stage phosphate bonding
treatment and finished with a high reflectance baked white
enamel after fabrication.
Shielding
Standard lens is an acrylic, matte white opal finish. Fixtures are
designed to accept any flat unframed sheet of light diffusing
plastic. Lens must lay in place and is supported by the extruded
trim on all four sides. Regressed trim is finished in matte white
and is 19⁄16″ deep. Trim is secured rigidly in place to the housing
with rivets. Larger sizes of luminaires (such as 4′ x 4′) may
require pre-arched panels in some shielding to prevent sagging.
Contact your Columbia Representative for details.
Type M
23⁄4″
19⁄16″
“Fit-in” style extruded trim
align with modular tile joints.
Fixture is supported from concealed suspension, includes
adjustable wing hangers.
Cantilever arm suspension
system included.
Labels
All fixtures carry a UL or CSA listing and bear the appropriate
UL labels.
Complete ordering information on back. Dimensions and specifications subject to change without notice.
T53
www.columbialighting.com • 3808 N Sullivan Rd, Bldg 29 • Spokane, WA 99216 • (509) 924-7000
FT1
SKYLIGHT Cross Sections
A - 1⁄2″ Diameter Knockout
B - 7⁄8″ Diameter Knockout
C - 11⁄ 2″ Diameter Knockout
Ordering Information
Example: SKY24-332G-RAOA-3EB8LH120-EL
-
SKY
-
RA
-
-
Series
Options
Fixture Size
14 - 1′ x 4′
22 - 2′ x 2′
24 - 2′ x 4′
Voltage
33 - 3′ x 3′
44 - 4′ x 4′
120 - 120V
277 - 277V
347 - 347V
UNV - 120V/277V
(T8 w/LH only)
No. of Lamps
1 - One 4 - Four
2 - Two 8 - Eight
3 - Three
SLL - Spring Loaded
Latches
SPH - Specular Laminate
Housing
GMF - Slow Blow Fuse
GLR - Fast Blow Fuse
EL - Emergency Battery
Pack
Ballast
Lamp Type
Blank
- HPF, T12, 20 Watt
LE
- Energy Saving Magnetic T12
EB8
- Electronic T8
EB8LH
- Electronic T8
3EB8
- (1) 3-Lamp Electronic T8
3EB8LH - (1) 3-Lamp Electronic T8
4EB8
- (1) 4-Lamp Electronic T8
4EB8LH - (1) 4-Lamp Electronic T8
24EB8
- (1) 2-Lamp & (1) 4-Lamp Electronic T8
24EB8LH - (1) 2-Lamp & (1) 4-Lamp Electronic T8
For a specific ballast vendor, show as option.
1 x 4, 2 x 4, 3 x 3, 4 x 4
40 - 4′, T12, 40 Watt
32 - 4′, T8, 32 Watt
2x2
40U6 - U-bent, T12, 40 Watt, 6″ Leg Spacing
40U3 - U-bent, T12, 40 Watt, 35⁄8″ Leg Spacing
32U6 - U-bent, T8, 32 Watt, 6″ Leg Spacing
31U1 - U-bent, T8, 31 Watt, 15⁄8″ Leg Spacing
17 - 2′, T8, 17 Watt
20 - 2′, T12, 20 Watt
Ceiling Type
G - Inverted T-Bar
F - Overlap Flange
M - Modular
Shielding
Door Style
RA - Regressed Aluminum
A12 - Pattern 12 Acrylic
OP - Opal Acrylic, Matte Finish (Std.)
CO 12/04
T53
3808 N Sullivan Rd, Bldg 29 • Spokane, WA 99216 • (509) 924-7000 • www.columbialighting.com
FT2
Catalog Number
Notes
Type
FEATURES & SPECIFICATIONS
INTENDED USE
High performance deep-cell parabolic luminaires for superior light control,
visual comfort and light cutoff in open area applications.
ATTRIBUTES
Choice of low iridescent diffuse or specular louver finishes. Also available with
AchromaTM non-iridescent louver finish.
Models available to meet IES RP-1 minimum luminance criteria for office
lighting systems in VDT applications. Optimax products are available to
meet preferred criteria.
CONSTRUCTION
Black reveal provides floating louver appearance, conceals optional airsupply slots. Optional heat-removal dampers and air-pattern control blades
allow airflow control.
Overlapping flange and modular ceiling trims factory-installed with standard swing-gate hangers or field convertible with optional trim and hangers. T-hinges die-formed for maximum strength. Latches spring-loaded,
concealed in reveal.
Housing formed from cold-rolled steel. Louvers formed from anodized aluminum. No asbestos is used in this product.
FINISH
Five-stage iron-phosphate pretreatment ensures superior paint adhesion
and rust resistance. Painted parts finished with high-gloss, baked white
enamel.
ELECTRICAL SYSTEM
Thermally-protected, resetting, Class P, HPF, non-PCB, UL Listed, CSA certified ballast is standard. Energy saving and electronic ballasts are sound
rated A.
Luminaire is suitable for damp locations. AWM, TFN or THHN wire used
throughout, rated for required temperatures.
LISTING
UL Listed (standard). CSA Certified or NOM Certified (see Options).
WARRANTY
Guaranteed for one year against mechanical defects in manufacture.
PARAMAX® Parabolic Troffer
PM3 2'x4'
3" Deep Louver
Specifications
48
(1218)
Length: 48 (1218)
Width: 24 (609)
Depth: 5-15/16 (151)
Weight: 35 lbs (16 kg)
5-15/16
(151)
24
(609)
All dimensions are inches (millimeters).
Specifications subject to change without notice.
ORDERING INFORMATION
Example: 2PM3 G B 3 32 24ND 120 GEB
2PM3
Series
2PM3 Paramax 3"
deep cell
parabolic,
2' wide
Number
of lamps
2, 3, 4, 6
Voltage
32 32W T8 (48")
40 40W T12 (48")
120, 277, 347,
MVOLT 2
Others
available.
Not included.
Trim type
Air function
G Grid
F Overlapping
flange
MT Modular fit-in
ST Screw slot
A Air supply/return
(slots in side trim)
H Heat removal
(through lamp
cavity, dampers
available)
D Combination A & H
B Static (no air
function, matching
appearance)
NOTES:
1 Where applicable, number of rows is divisible
by number of lamps unless specified otherwise.
2 MVOLT available with GEB10IS only.
3 Only available with 3-lamp 18 and 24 cell
versions.
Fluorescent
Lamp type
Number
of cells1
12 , 16 , 18,
24, 32
Louver finish
ND AchromaTM noniridescent diffuse
silver
LD Low iridescent
anodized diffuse
silver
LS Low iridescent
anodized
specular silver
C Diffuse gold
anodized
(champagne)
Options
1/3
1/4
GEB
GEB10IS
GEB10RS
EL
LST
PWS1836
GLR
GMF
LP__
CRE
CRM
HRD
APB
ACS
PAF
JP10
CSA
NOM
2R
One 3-lamp ballast
One 4-lamp ballast
Electronic ballast, <20% THD
Electronic ballast, <10% THD, Instant Start
Electronic ballast, <10% THD, Rapid Start
Emergency battery pack (nominal 300 lumens;
see Fluorescent Battery Packs tab)
Tandem fixture pairs (shared ballasts)
6' prewire, 3/8" dia., 18-gauge, 3 wires
Internal fast-blow fuse
Internal slow-blow fuse
Lamped; specify lamp type and color
Flanged trim for continuous row mounting (end)
Flanged trim for continuous row mounting
(middle)
Heat-removal dampers
Air-pattern control blades (A and D models only)
Air closure strips (A and D models only)
Painted after fabrication (white enamel)
Palletized and stretch-wrapped without
individual cartons (10 per), G and MT trim only
CSA Certified
NOM Certified
Two reflector channel covers3
Sheet #: PM3-2x4
PAR-240
E
GR1
Tesis Recessed floor luminaire
Lens wallwasher for metal halide lamps
410
∅ 297
∅ 277
Size 7
50°
HIT-CE
5 koo3m
IP68
33724.000
Reflector colour Silver
HIT-CE 70W G12 6600lm
Product description
Housing: corrosion-resistant cast
aluminium, No-rinse surface treatment. Black double powder-coated.
Mounting by means of an adjustable bar. Clamp extension up to
35mm.
Cable 3x1.5mm², L 1m.
Control gear with temperature
controller, timed ignitor, capacitor.
Wallwasher reflector: Aluminium,
silver anodised.
Darklight reflector: aluminium,
silver, bright anodised, with wallwasher lens. Cut-off angle 50°.
Without spill light.
Screw-mounted cover ring with
flush safety glass: corrosion resistant stainless steel.
Safety glass: 12mm, clear. Surface
temperature 75°C. Can be driven
over by vehicles with pneumatic
tyres. Load 44kN.
Installation with separate connection sleeve.
Protection mode IP68 3m: protection against dust ingress, and
continuous immersion up to 3m
deep.
On site protection must be
provided using a residual current
circuit breaker, FI<30mA.
Weight: 10.20 kg
ERCO Leuchten GmbH
Postfach 24 60
58505 Lüdenscheid
Deutschland
Tel.: +49 2351 551-0
Fax: +49 2351 551-300
[email protected]
750 cd/klm
150°
150°
120°
120°
HIT-CE 70W G12 6600lm
Technical Region: 230V/50Hz
Edition: 13.12.2004
Please download the current version
from
www.erco.com/33724.000
1/2
E
GR2
LED orientation luminaire
70
2
∅ 56
∅ 40
∅ 45
LED
0q z
koo3m
IP68
33764.000
LED White
Product description
Housing with gasket: stainless
steel.
Installation bush with ribs: plastic.
Cable 4x0.75mm², L 500mm.
LED module:
Power consumption 0.5W.
Nominal voltage 30V DC.
Clear prismatic diffuser with
circular light aperture.
Cover ring: corrosion resistant
stainless steel, with 6mm safety
glass. Load 5kN.
Control gear to be ordered separately.
Protection mode IP68 3m: protection against dust ingress, and
continuous immersion up to 3m
deep.
Weight: 0.16 kg
ERCO Leuchten GmbH
Postfach 24 60
58505 Lüdenscheid
Deutschland
Tel.: +49 2351 551-0
Fax: +49 2351 551-300
[email protected]
Technical Region: 230V/50Hz
Edition: 13.12.2004
Please download the current version
from
www.erco.com/33764.000
1/3
L1
PH 4 1/2 -3 1/2 Glass Floor
Photometric Report:
Report No.:
Poulsen Report No.:
Luminaire:
Lamp:
Efficiency:
Description:
Candlepower Distribution
Vertical Angle
Candela
0
196
5
20
10
208
25
252
35
183
45
159
55
138
65
102
75
57
90
24
120
28
150
53
180
44
Coefficients of Utilization - Zonal Cavity Method
Effective Floor Cavity Reflectance 20%
Ceiling Reflectance (%)
80
Wall Reflectance (%)
70
50
30
Room Cavity Ratio
0
63
63
63
1
57
54
51
2
51
47
43
3
47
41
36
4
43
26
31
5
39
32
27
6
36
29
24
7
33
26
21
8
31
24
19
9
29
22
17
10
27
20
16
Zonal Lumen Summary
Zone
Lumens
0-30
197
0-40
315
0-60
561
0-90
758
90-120
69
90-130
98
90-150
161
90-180
207
0-180
965
70
50
30
10
50
50
30
10
50
30
30
10
50
10
30
10
0
0
63
49
40
33
27
23
20
18
16
14
13
60
54
49
44
40
37
34
32
29
27
26
60
52
45
39
34
30
28
25
23
21
19
60
49
41
35
20
26
23
21
18
17
15
60
47
38
32
27
23
20
17
15
14
12
55
47
41
36
32
28
25
23
21
19
18
55
45
38
32
28
24
22
19
17
16
14
55
44
36
30
25
21
19
16
15
13
12
50
43
37
33
29
26
23
21
19
18
17
50
41
35
30
26
23
20
18
16
15
13
50
40
33
28
23
20
18
16
14
12
11
45
39
34
30
26
24
21
20
20
17
15
45
38
32
28
24
21
19
17
17
14
13
45
37
31
26
22
19
17
15
15
14
11
43
35
29
24
20
17
15
13
12
11
10
Material
Shades: Handblown white opal glass.
Base: High lustre chrome plated,
spun brass. Top plate: High lustre
chrome plated, spun brass. Stem:
High lustre chrome plated, steel.
Label
cUL, Dry location. IBEW.
% Fixture
20.4
32.6
58.1
78.5
7.2
10.2
16.7
21.5
100.0
70
Finish
White opal glass. High lustre chrome
plated.
Weight
Max. 34 lbs.
% Lamp
11.3
18.0
32.1
43.3
3.9
5.6
9.2
11.8
55.1
10
PH 41/2 -31/2 Glass Floor (1927) provides soft illumination. The PH 41/2
family is based on the principle of a
reflecting multi-shade system, producing a harmonious and glare free
illumination. The shades are drawn
over a logarithmic spiral, with the
center of the light source placed in
the spiral’s focal point.
Mounting
Cord type: Black. Cord length: 9'.
Plug: 120V.
incandescent
PH41/2-31/2-F-1-100W-A19-IF.IES
LP0380
PH41/2-31/2-F-1-100W-A19-IF.IES
PH 4 Glass Table and Floor
1/100W/A19/IF
55.1%
All data shown are per 1750 lumens. This report
can be used for calculation on all versions. Use
only actual lumen data when calculating.
s p e c i f i c a t i o n
Ordering example:
1
2
Prod.code
Light source
PH41/2-31/2-F
1/100W/A-19/IF medium
1
3
Volt.
120V
4
Finish
GLASS
Product code
PH41/-31/-F
2
2
2
Light source
1/100W/A-19/IF medium
3
Voltage
120V
4
Finish
GLASS
Info notes:
I. In-line on/off foot switch provided.
II. All handblown opal glass shades are
sandblasted on the undersides for uniform light distribution.
III. The comparable EU version has the
following classification: Ingress
Protection Code: IP20.
Spare parts:
PH41/2 -31/2 top shade
PH41/2 -31/2 middle shade
PH41/2 -31/2 lower shade
Louis Poulsen Lighting, Inc., 3260 Meridian Parkway, Fort Lauderdale, FL 33331 Telephone: (954) 349-2525 Fax: (954) 349-2550
www.louispoulsen.com
P1
The original BEGA classic caged sphere
General purpose pole mounted sphere luminaires with diffused source.
Enclosure: Molded high impact acrylic, minimum 1 ⁄8" thick, two piece
half spheres clamped and gasketed at the equator by a die cast
aluminum six spoke lower guard and clamping ring secured by eight (8)
socket head stainless steel fasteners. (9150/9156 is hand blown,
seamless, three-ply opal glass). Enclosure assembly is secured to fitter
by four (4) socket head stainless steel set screws threaded into stainless
steel inserts.
Guard: One piece 8-rib die cast aluminum slip fitter slip fits pole and is
secured by secured by six (6) stainless steel socket head set screws.
9150/9156/9250/9350 slip fit a 2 3 ⁄8 " O.D.; 9259 slip fits a 3" O.D.
Electrical: Lampholders: Incandescent are medium base porcelain with
nickel plated copper screw shell supplied with 200°C high temperature
leads, rated 600V. H.I.D. rated 4KV. Fluorescent are type GX23-2 (13W).
Ballasts are located in the base of the selected BEGA pole and are
available in 120V or 277V, HPF - specify.
Finish: Standard finish is an eight step process consisting of two
coats of black or white polyurethane, one with light texture over a
phosphate base.
Custom colors supplied on special order.
U.L. listed, suitable for wet locations.
•
Options
Application Photo
Photometry
Pole mounted luminaires with lower
guard. Die cast aluminum fitter
which slip fits a pole top or tenon.
9150, 9156, 9250, 9350 slip fits 23⁄8 "
O.D. and 9259 slips 3"O.D.
Three-ply opal glass standard on
9150, 9156; optional opal acrylic
available - suffix PDC. Opal DR
acrylic half spheres clamped at the
equator standard on 9250, 9350,
9259.
Color: Black or white.
Note: Metal Halide and HPS
pole top units require ballasts
mounted in base of 5" butt pole.
B
•
Lamp
Lumen
A
B
9150
Pole top
1
100W A-19
1750
13 ⁄4 161 ⁄4
9156P
Pole top
1
13W PLC
860
13 3⁄4 161 ⁄4
9250
Pole top
1
150W A-21
2850
17 3⁄4 201 ⁄4
9350S
3
Pole top
1
50W E-17 HPS
4000
17 3⁄4 201 ⁄4
9350MH Pole top
1
100W ED-17 MH
8500
17 3⁄4 201 ⁄4
Pole top
1
70W E-17 HPS
6400
215 ⁄8 251 ⁄2
9259MH Pole top
1
175W ED-17 MH
14000
215 ⁄8 251 ⁄2
9259S
Type:
BEGA Product #:
Project:
Voltage:
Color:
Options:
Modified:
BEGA/US 1000 BEGA Way, Carpinteria, CA 93013 [P] 805·684·0533
©Copyright BEGA/US 2002 updated 6/02
[F] 805·684·6682
SC1
Sample Catalog Number
CB6638
1FS24(120V)
Model
L a m p ( Vo l t a g e )
-
LBZ
Fr a m e F i n i s h
CAL
Pa n e l F i n i s h
XPS
Option
Options
Model
L a m p ( Vo l t a g e )
Fr a m e F i n i s h
Pa n e l F i n i s h
CB6638
1 F S 2 4 24w T-5/HO, mini bi-pin base
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
B A Brushed Aluminum
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
( Vo l t a g e )
120V
277V
• ABA
IEM
FU
• DIM
ULD
VR
XPS
Hand painted alabaster alternative
Integral emergency battery pack
Fusing
Fluorescent dimming, Lutron Eco-10
UL damp location label (painted only)
Vandal resistant housing fasteners
Express 10 day shipment
• Option is not available with X P S program
Options
Model
L a m p ( Vo l t a g e )
Fr a m e F i n i s h
Pa n e l F i n i s h
CB6640
1 F S 3 9 39w T-5/HO, mini bi-pin base
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
B A Brushed Aluminum
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
( Vo l t a g e )
120V
277V
• ABA
IEM
FU
• DIM
ULD
VR
XPS
Hand painted alabaster alternative
Integral emergency battery pack
Fusing
Fluorescent dimming, Lutron Eco-10
UL damp location label (painted only)
Vandal resistant housing fasteners
Express 10 day shipment
• Option is not available with X P S program
Model
L a m p ( Vo l t a g e )
Fr a m e F i n i s h
Pa n e l F i n i s h
CB6642
1 F S 5 4 54w T-5/HO, mini bi-pin base
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
B A Brushed Aluminum
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
( Vo l t a g e )
120V
277V
Options
• ABA
IEM
FU
• DIM
ULD
VR
XPS
Hand painted alabaster alternative
Integral emergency battery pack
Fusing
Fluorescent dimming, Lutron Eco-10
UL damp location label (painted only)
Vandal resistant housing fasteners
Express 10 day shipment
• Option is not available with X P S program
Model
L a m p ( Vo l t a g e )
Fr a m e F i n i s h
Pa n e l F i n i s h
CB6644
1 F S 8 0 80w T-5/HO, mini bi-pin base
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
B A Brushed Aluminum
P T D Painted - specify color code,
see page 519
(ex. WHT for White)
( Vo l t a g e )
120V
277V
Options
• ABA
FU
ULD
VR
XPS
Hand painted alabaster alternative
Fusing
UL damp location label (painted only)
Vandal resistant housing fasteners
Express 10 day shipment
• Option is not available with X P S program
Features
Va r i a t i o n s
▼
ADA compliant
Extruded aluminum frame
▼ Solid metal trim and accents
▼ Oven cured low VOC lacquer paint
▼ 1/8” thick virgin acrylic diffuser with matte
finish, UV stable, UL-94 HB Flame Class rated
▼ Easy tool-less relamping
▼ Fluorescent lamping
▼ High power factor electronic ballast
▼ Shallow 3-1/2” depth recessed housing rated
for through-circuit wiring
▼ Recessed housing in stock and available for
rough-in installation
▼ Rated for insulation contact
▼ 5 year product warranty
▼
▼
▼
Specialty finishes to match architectural detail
Mix and match accents and trim from other
product designs
▼ Increase/decrease fixture height and/or width
Installation Instructions
Stud
Wall Cutout
4-3/4"
1" Maximum
wall thickness
RL
3-1/2"
Note: One long edge of
cutout must be adjacent
to a wall stud or other
appropriate mounting
structure.
Fixture Length
RL
24”
23-1/2”
36”
35-1/2”
47-1/2”
47”
59-1/2”
59”
94271 artres_sconce4
10/1/04
9:20 AM
Page 1
SC2
ARTRES SCONCE
Catalog Number
FIXTURE
ARS – Artres Sconce
VOLTAGE
120 – 120 Volt
277 – 277 Volt
EXAMPLE: ARS-120
Specifications
CONSTRUCTION
FINISH
LAMPING
Fixture is constructed of extruded aluminum,
type F22. All seams and edges are welded
together with invisible welds. Fixture mounts
to wall-bracket with recessed screws.
Finished in lightly textured gray polyester powdercoat. Finish specially developed for outside
exposure with excellent all weather resistance.
Single, 35 Watt, MR-11. Lamp is placed
above the vertical window to evenly illuminate
both sides of the vertical opening. Lamp not
included.
SHIELDING
Specify 120 volt or 277 volt. Fixture is
supplied with internal electronic transformer
and is fully gasketed and U.L./C.U.L. wet
location labeled. Fixture may be dimmed
with no special modification or specification.
Lamp openings are shielded with gasketed
glass plates.
ELECTRICAL
MOUNTING
Fixture is supplied with an Énergie junction
box. See reverse for detail. Fixture may be
mounted in any orientation.
Dimensions
2.1"
8.6"
13.3"
2.0"
4.3"
Energie LLC, 405 Urban Street, Ste 402 Lakewood, CO 80228 Tel 720 963 8055 Fax 720 963 8044 www.energielighting.com
In an effort to continually improve our products, we reserve the right to change or modify designs and/or materials without prior notice.
All rights reserved. These products may be covered by one or more U.S. or international patents or patents pending. 10/04
SC3
Wall up/downlight luminaires
High output wall mounted luminaires with fully shielded light source for
dual up and down lighting effects for indoor or outdoor applications.
Housing: One piece die cast aluminum supplied with universal
mounting bracket for direct attachment to 31⁄ 2" or 4" octagonal wiring
box (6610/615) use 538 small opening wiringbox). A round “rotation”
plate allows the housing to be precisely leveled (or rotated) after
installation.
Enclosure: Tempered clear glass, 3⁄16" thick, retained by one piece die
cast aluminum step baffle frame on bottom, flush on top, secured by
stainless steel screws threaded into stainless steel inserts. Internal full,
dual semi-specular optical system. Fully gasketed for weather tight
operation using molded silicone rubber “U-channel”.
Electrical: Lampholders: Incandescent are double contact bayonet,
(6610) stainless steel with porcelain insulator disk with 250°C high
temperature leads, rated 600V, or medium base porcelain (6615) with
nickel plated copper screw shell supplied with 200°C high temperature
leads. H.I.D. are G12, bi-pin, pulse rated 4KV.
Ballasts: are magnetic, HPF, available in 120V or 277V - specify.
Finish: Standard finish is an eight step process consisting of two coats
of black or white high solids, UV stabilized polyurethane, one with light
texture over a phosphate base.
Custom colors supplied on special order.
U.L. listed, suitable for wet locations.
Type:
BEGA Product #:
Project:
Voltage:
Color:
Options:
Modified:
Photometry
•
B
•
•
A
•
C
•
•
Lamp
•
B
•
•
A
6610/538
•
•
Wall
C
•
Lumen
A
B
C
1 Q100W T4 DCB
1800
4 3⁄8
61⁄4
61⁄4
58
8 1⁄2
6615/538
Wall
1 Q150W MED T10
2500
538
Small opening wiring box included
6
BEGA/US 1000 BEGA Way, Carpinteria, CA 93013
©Copyright BEGA/US 2002 updated 6/02
8 ⁄
Lumen
A
12
B
C
7 16
6616MH Wall
1
39W G12T6 MH
3300
7⁄
10 ⁄
6620MH Wall
1
70W G12T6 MH
6600
8 5⁄8
12 9⁄16 13 9⁄16
Wall mounted luminaires with fully
shielded single horizontal light
source for up/down lighting.
Die cast aluminum housing, arm,
canopy and step baffle.
Full anodized aluminum double
reflector with clear tempered
glass.
Color: Black or white.
Lamp
Wall mounted luminaires with fully
shielded single, horizontal light
source for up/down lighting.
Die cast aluminum housing, arm,
canopy and step baffle. Full
anodized aluminum double
reflector with clear tempered glass.
Color: Black or white.
[P] 805·684·0533
[F] 805·684·6682
12
Large outdoor, remote
1:10 Scale
Uplighting
V Mount
8"
(203mm)
8-7/8"
(225mm)
Source
HPS
MH
Halogen
17-13/16" *
(452mm)
5-1/8"
(130mm)
Wattage
150
175
300-500
MH/HPS
24-7/8" *
(632mm)
Length
250, 400
Halogen
MH/HPS
12-1/16"
(306mm)
900,1000
2x400
A
B
E
F
G
H
Length (see chart)
1:12 Scale (For
8-7/8"
(225mm)
Metal
Halide
D
C
B
J
K
O
2-1/4"
(57mm)
36"
(915mm)
M
L
N
High Pressure
Sodium
Cantilever 1:12 Scale
(For use with X Mount)
4"
(102mm)
M Welded aluminum
mounting plate with
splice access cover
N Recessed outlet box
O Accessory extruded
aluminum slipfitter for
2-3/8" O.D. pole or tenon
Electrical:
Use 90°C wire for supply connections. Leads exit reflector
through watertight flush cord entry, silicone coated fiberglass
sleeving; 8" exposed beyond nipple. (60" leads on X mount).
Tungsten halogen - recessed single contact (RSC)
lampholders in patented clamping supports for maximum
heat dissipation.
Metal halide - position oriented mogul lampholder for use with
either POMB horizontal or universal position lamp (medium
base for 175W). Rotating bracket allows horizontal lamp to be
locked in proper position after aiming (hinged lampholders for
2x400W are fixed in position for uplighting across overhead
surface). End-of-lamp aligner ensures consistent optical
performance and minimizes damage from shock or vibration.
HPS - pulse rated mogul lampholder (medium base for 150W).
Ballast - remote HPF constant wattage autotransformer (CWA)
rated for -20°F/-29°C starting (high reactance autotransformer
(HX-HPF) for 150W HPS). Weatherproof aluminum enclosure
includes three 7/8" dia. entries and one 3/8" liquidtight conduit
connector. Optional remote ballast for dry indoor location.
For complete ballast specifications, see Accessories Section.
H 1/2" NPT nipple
J Aluminum reveal
plates (black)
K Specular extruded
aluminum reflector
1-1/2" x 2" aluminum arm
L
Side-Mount Slipfitter
use with X Mount)
5-7/8"
(149m)
6"
(152mm)
4-1/8"
(105mm)
D Tamper-resistant
captive door screws
E Die-cast aluminum
end plates
F Locking set screw
G Aluminum yoke
* Yoke includes (2) 9/32" dia. holes at
12" (305mm) centers for supplemental
mounting support (1/4" fasteners
by others)
Specifications
A Mitred extruded
aluminum door with
silicone gasket
B Cutoff visor (included)
C Clear, flat, thermal
and impact resistant
tempered glass lens
Finish:
Exterior surfaces - 6 stage pretreatment and electrostatically
applied thermoset polyester powder coating for a durable
abrasion, fade and corrosion resistant finish. Choice of
semi-gloss colors (see ordering information).
Reflector and internal end plates - extruded high purity
aluminum with clear anodized specular finish. All hardware
and components - non corrosive stainless steel or aluminum.
Door secured with captive tamper-resistant (#10 Torx) screws
in stainless steel threaded reflector inserts to prevent seizing.
Yoke attaches with recessed hex socket screws.
Mounting:
1/2" NPT nipple (wet location outlet box or fitting by others).
Aluminum cantilever mounting assembly ordered separately;
specify X mount. Suitable backing structure required.
Accessory slipfitter ordered separately. Top-mount for single
unit, or side-mount for one or two (back-to-back) units; specify
X mount. Fits 2-3/8" O.D. stanchion, pole or tenon (by others).
Standard:
UL listed or CSA certified for wet locations.
REV. 11/02
Tungsten
Halogen
Features
Style 152
metal halide for uplighting large vaults, canopies or arches
■ Compact yet powerful - up to 1000W halogen, 2x400W
metal halide, end-of-lamp aligner, set screw locks aiming
■ Optimum performance - high output position oriented
24000
Cd
400W
MH
900W
TH
tempered glass lens, tamper-resistant door screws
■ Built to last - all aluminum and stainless steel components,
Performance
Two parabolic reflector
sections drive light
across the overhead
plane from one edge.
An elliptical section
redirects its light to a
parabola and shields
the lamp. Asymmetry
is maximized resulting
in high beam efficiency
and superior surface
uniformity. The fast
"runback" minimizes
wasted spill light.
Wide lateral distribution
permits greater
spacings.
For complete photometrics, visit www.elliptipar.com
elliptipar
SC4
U
7.0
U
7.1
To Order
2
1 5 23
4
To form a Catalog Number
1
1 Source
M = Metal halide
H = High pressure sodium
T = Tungsten halogen
2 Style
-
152 = Large outdoor, remote ballast
8
Distance
7
-V
Ballast
105'(32m)
75'(23m)
50'(15m)
50'(15m)
6
Voltage(s)
CWA
CWA
CWA
CWA
5
Lamp WattCode age
A, B, H
A, B, H
A, B, H
A, B, H
3 Lamp
Metal Halide*
0175
175 MH175/U/MED
0250
250
MH250/HOR
0400
400
MH400/HOR
2400‡ 2x400 (2) MH400/HOR
A, B, H HX-HPF 5'(1.5m)
A, B, H
CWA
5'(1.5m)
A, B, H
CWA
10'(3.0m)
A, B, H
CWA
10'(3.0m)
Lamp
Number
High Pressure Sodium
0150
150
LU150/MED
0250
250
LU250
0400
400
LU400
2400 2x400
(2) LU400
Tungsten Halogen
0300
300
Q300T3
A
0350+ 350 Q350T3/CL/HIR+
A
0500
500
Q500T3
A
0900+ 900 Q900T3/CL/HIR+ B, G
1000 1000
Q1000T3
A, F, G
elliptipar
For complete lamp and ballast information, see Accessories Section.
* Use clear metal halide horizontal or universal position lamp with
compact envelope. 250 and 400W lamps are horizontal position
oriented mogul base (POMB) that yield higher light output than
universal position lamps. Standard metal halide lamp colors are
4000K for 175W, 3200K for 250 and 400W.
‡ 2x400W metal halide uses position oriented mogul lampholders that
are hinged and fixed in position to uplight across an overhead
surface (±15°).
+ 350 and 900W IR coated halogen yield approximately the same light
output as conventional 500 and 1500W halogen lamps respectively.
REV. 6/04
Project:
4 Mounting
Semi-gloss white
Dark bronze
Silver
Semi-gloss black
Green
G = 240V
(900W, 1000W TH only)
H = 347V
99 = Custom RAL or
computer matched
color to be specified,
consult sales
representative.
V = External yoke with 1/2" NPT nipple (wet location outlet
box or fitting by others)
X = External yoke for use with accessory cantilever or
slipfitter (order separately)
=
=
=
=
=
5 Finish
02
06
07
08
12
6 Voltage
A = 120V
B = 277V
F = 220V
(1000W TH only)
7 Option (See Accessories Section for specifications)
V0 = Cutoff visor included, no other options
VD = Remote ballast for dry indoor location
VH = Long distance remote HPS ballast up to 35' (10m) for
150W HPS, up to 50' (15m) for 250W and 400W HPS
VL = Micro-prismatic tempered glass lens (replaces clear,
flat lens, offers smoother light pattern at reduced peak
candlepower.)
VX = For modification not listed, include detailed description.
Consult factory prior to specification.
Note: Cutoff visor included unless specified otherwise.
8 Standard
0 = UL, Underwriters Laboratories
J = CSA, Canadian Standards Association
Example
H152 - 0400 - V - 07 - B - VH0
■
Large outdoor model for use with 400 watt high pressure
sodium lamp. External yoke with 1/2" NPT nipple. Silver
powder coat finish. Long distance (up to 50') remote 277V
ballast in weatherproof enclosure. UL. Cutoff visor included.
■
elliptipar
114 Boston Post Road, West Haven, Connecticut 06516, USA
Voice 203.931.4455 Fax 203.931.4464 www.elliptipar.com
Type:
Accessories
Style 152
Order separately. See Accessories Section for specifications.
5 Finish
T10 = Top-mount slipfitter,
for 2-3/8" O.D. pole,
stanchion or tenon
(for use with single
X mount unit)
AC
36
= Cantilever,
36" (914mm) setback
(for use with X mount unit)
0 = UL
J = CSA
5 Finish
L = single unit
U = double unit (back to back)
ASF
ASF
S
0 = Side-mount slipfitter,
for 2-3/8" O.D. pole,
stanchion or tenon
(for use with
X mount units)
1 = single unit
2 = double unit
(back to back)
5 Finish
AE
V
0D0 = External vertical blade baffle, black,
for lengthwise shielding
2 = 25° shielding
4 = 45°
C = 300W-350W TH; 150W-175W HID
(not for use with 500W TH)
D = 250W, 400W HID
F = 900W, 1000W TH, 2x400W HID
= Ballast fuse kit
AXF = Wet location color filter assembly,
interchangable frame with
stripped color glass, visor.
Not suitable for all lamp
wattages. Consult factory for
complete specifications and
ordering information.
AFK000X
0 = UL
J = CSA
The external shapes of the asymmetric reflectors are trademarks of elliptipar.
Certain products illustrated may be covered by applicable patents and patents pending.
For a list of patents, see Contents pages. These specifications supersede all prior
publications and are subject to change without notice. ©2004 elliptipar.
SC4
A
B
E
F
G
H
M
12"
(305mm)
(For use with X Mount)
1:12 Scale
D
A
C
B
J
K
L
M
Ceramic
Metal Halide
N
O
Tungsten Halogen
Cantilever 1:12 Scale
(For use with X Mount)
30"
(762mm)
1-3/8"
(35mm)
M Accessory extruded
aluminum slipfitter for
2-3/8" O.D. pole or tenon
N Welded aluminum
mounting plate with
splice access cover
O 1" x 1-1/2" aluminum arm
Electrical:
Use 90°C wire for supply connections. Leads exit reflector
through watertight flush cord entry and silicone coated
fiberglass sleeving with 8" (.2m) exposed beyond nipple.
60" (1.5m) leads for X mount .
Tungsten halogen - recessed single contact (RSC) or
DC bayonet lampholders retained with patented clamping
supports for maximum heat dissipation.
Metal halide - G12 lampholder for use with single ended lamp.
Remote HPF high reactance autotransformer (HX-HPF) ballast
rated for -20°F/-29°C starting. Die-cast aluminum
weatherproof ballast enclosure includes four 1/2" NPT
threaded entries. Optional electronic ballast with automatic
shut-off to eliminate end-of-life cycling. Optional remote
ballast for dry indoor location.
For complete ballast specifications, see Accessories Section.
Standard:
UL listed or CSA certified for wet locations.
H 1/2" NPT nipple
J Aluminum reveal
plates (black)
K Specular extruded
aluminum reflector
1/2" NPT entry (with plug)
L
Top-Mount Slipfitter
6-1/2"
(165mm)
7-1/2"
(190mm)
3"
(76mm)
D Tamper-resistant
captive door screws
E Die-cast aluminum
end plates
F Locking set screw
G Aluminum yoke
1:12 Scale
5-1/4"
(133mm)
Small outdoor, remote
1:8 Scale
Uplighting
V Mount
4-3/4"
(121mm)
3"
(76mm)
(For use with X Mount)
Side-Mount Slipfitter
3-3/8"
(86mm)
6"
(152mm)
11-3/8"
(289mm)
Specifications
A Mitred extruded
aluminum door frame
with silicone gasket
B Cutoff visor (included)
C Micro-prismatic, thermal
and impact resistant
tempered glass lens
Finish:
Exterior surfaces - 6 stage pretreatment and electrostatically
applied thermoset polyester powder coating for a durable
abrasion, fade and corrosion resistant finish. Choice of
semi-gloss colors (see ordering information).
Reflector - extruded high purity aluminum with clear anodized
specular finish. All hardware and components - non corrosive
stainless steel or aluminum. Door secured with captive
tamper-resistant (#10 Torx) screws in stainless steel threaded
reflector inserts to prevent seizing. Yoke attaches with
recessed hex socket screws.
Mounting:
1/2" NPT nipple (wet location outlet box or fitting by others).
Aluminum cantilever mounting assembly ordered separately;
specify X mount. Suitable backing structure required.
Accessory slipfitter ordered separately. Top-mount for single
unit, or side-mount for one or two (back-to-back) units; specify
X mount. Fits 2-3/8" O.D. stanchion, pole or tenon (by others).
REV. 4/04
Features
Style 151
ideal for unobtrusive uplighting of soffits, canopies, vaults
■ Compact size, minimal setbacks and wide spacings -
tamper-resistant fasteners, set screw in yoke locks aiming
■ Durable and secure - thermal and impact resistant lens,
70W
MH
3000
Cd
250W
TH
out dirt and moisture, maintain performance
■ Precured silicone gaskets, unique flush cord entry - seal
Performance
Two parabolic reflector
sections drive light
across the overhead
plane from one edge.
An elliptical section
redirects its light to a
parabola and shields
the lamp. Asymmetry
is maximized resulting
in high beam efficiency
and superior surface
uniformity. The fast
"runback" minimizes
wasted spill light.
Wide lateral distribution
permits greater
spacings.
For complete photometrics, visit www.elliptipar.com
elliptipar
SC5
U
1.0
U
1.1
To Order
1 5 1 2
3
4
To form a Catalog Number
1
1 Source
M = Metal halide
T = Tungsten halogen
2 Style
-
151 = Small outdoor, remote ballast
3 Lamp
Voltage(s)
5
6
8
15'(4.5m)
15'(4.5m)
10'(3m)
15'(4.5m)
10'(3m)
15'(4.5m)
Distance
7
-V
Ballast
Lamp
Number
Lamp WattCode age
HX-HPF
Electr.
HX-HPF
Electr.
HX-HPF
Electr.
150 CMH150/T6/G12
A
A
A
A
Ceramic Metal Halide*
A, B
035G 35
CMH35/T6/G12
1, 2
A, B, H
070G 70
CMH70/T6/G12
1, 2
A, B, H
1, 2
150G
Tungsten Halogen
0100 100
Q100DC
0150 150
Q150DC
0200 200
Q200T3
0250 250
Q250DC
For complete lamp and ballast information, see Accessories Section.
* Metal halide lamps using ceramic arc tubes yield higher light output
than lamps with quartz arc tubes. They offer improved lamp-to-lamp
color consistency and a more stable color temperature over their
life (±200K). Standard lamp color is 3000K / 80+ CRI.
4 Mounting
Semi-gloss white
Dark bronze
Silver
Semi-gloss black
Green
elliptipar
elliptipar
99 = Custom RAL or
computer matched
color to be specified,
consult sales
representative.
V = External yoke with 1/2" NPT nipple (wet location outlet
box or fitting by others)
X = External yoke for use with accessory cantilever or
slipfitter (order separately)
=
=
=
=
=
5 Finish
02
06
07
08
12
REV. 4/04
Project:
6 Voltage/Ballast
Magnetic
A = 120V
B = 277V
H = 347V (Canada)*
* Not available for 35W metal halide
Electronic
1 = 120V
2 = 277V
7 Option (See Accessories Section for specifications)
V0 = Cutoff visor included, no other options
VD = Remote ballast for dry indoor location
VH = Long distance remote metal halide ballast,
35W: 15' min. up to 50’ max. (4.5m - 15m),
70W: up to 50' max. (15m),
150W: up to 50’ max. (15m)
VX = For modification not listed, include detailed description.
Consult factory prior to specification.
Note: Cutoff visor included unless specified otherwise.
8 Standard
0 = UL, Underwriters Laboratories
J = CSA, Canadian Standards Association
Example
M151 - 150G - X - 06 - A - VDJ
■
Small outdoor model for use with 150 watt metal halide lamp.
External yoke for use with accessory cantilever or slipfitter
(order separately). Dark bronze powder coat finish. Remote
encapsulated 120V magnetic ballast suitable for dry indoor
location. CSA. Cutoff visor included.
■
elliptipar
114 Boston Post Road, West Haven, Connecticut 06516, USA
Voice 203.931.4455 Fax 203.931.4464 www.elliptipar.com
Type:
Accessories
5 Finish
T10 = Top-mount slipfitter,
for 2-3/8" O.D. pole,
stanchion or tenon
(for use with single
X mount unit)
S = single unit
V = double unit
(back to back)
5 Finish
Style 151
30
= Cantilever,
30" (760mm) setback
(for use with X mount unit)
0 = UL
J = CSA
Order separately. See Accessories Section for specifications.
AC
ASF
ASF
S
0 = Side-mount slipfitter,
for 2-3/8" O.D. pole,
stanchion or tenon
(for use with
X mount units)
1 = single unit
2 = double unit
(back to back)
5 Finish
AXF = Wet location color filter assembly,
interchangable frame with
stripped color glass, visor.
Maximum 200W TH, 70W CMH.
Note: Consult factory for complete
specifications and ordering information.
= Ballast fuse kit
AEBV
0D0 = External vertical blade baffle, black
for lengthwise shielding
2 = 25° shielding
4 = 45°
AFK000X
0 = UL
J = CSA
The external shapes of the asymmetric reflectors are trademarks of elliptipar.
Certain products illustrated may be covered by applicable patents and patents pending.
For a list of patents, see Contents pages. These specifications supersede all prior
publications and are subject to change without notice. ©2004 elliptipar.
SC5
SP1
E
Quadra Directional spotlight
12 1/8"
307 mm
8 3/4"
223 mm
for low-voltage halogen lamps
CO 4 7/8"
CO ∅ 123 mm
15 3/8"
391 mm
5 1/4"
∅ 133 mm
MRC16
Lä ö B
Dry Damp Wet
ÄIndoor
88045.023
MRC16 50W 12V GU5.3 10°
MRC16 50W 12V GU5.3 36°
Product description
Mounting plate: plastic, white.
Mounting ring for lampholder carrier: cast aluminum, white
(RAL9002) powder-coated. 360°
rotation.
Lampholder carrier: cast aluminum,
black powder-coated, designed as
heat sink. 40° tilt.
Double-sided, reversible mounting frame to cover the ceiling
aperture or for use as flush ceiling, trim detail: cast aluminum,
white (RAL9002) powder-coated.
Mounting bracket: metal.
Mounting box for preinstallation
with junction box for throughwiring, black powder-coated.
Magnetic transformer 120/12V,
60Hz inside mounting box. Snapin plug for connection between
transformer and luminaire.
Anti-glare ring: plastic, black, external white (RAL9002) lacquered.
Type Non IC luminaire.
Insulation materials must be kept
away from the luminaire by a minimum of 3". Thermally protected
luminaire. Suitable for damp location. Removal of luminaire allows
access to transformer and junction
box from below.
Max. ceiling thickness 3/4".
Use lamps with up to 36° max.
beam angle.
Weigth: 13.01 lbs / 5.90 kg
ERCO Lighting, Inc.
160 Raritan Center Parkway
Suite 10
Edison, NJ 08837
USA
Tel.: +1 732 225 8856
Fax: +1 732 225 8857
[email protected]
60°
30°
60°
60°
30°
30°
15000 cd
60°
30°
3000 cd
MRC16 50W 12V GU5.3 10°
MRC16 50W 12V GU5.3 36°
h(ft)
h(ft)
3
6
9
12
15
E(fc) D(ft)
10°
1363 0’6"
341 1’1"
151 1’7"
85 2’1"
55 2’7"
3
6
9
12
15
E(fc) D(ft)
36°
231 1’11"
58 3’11"
26 5’10"
14 7’10"
9 9’9"
Technical Region: 120V/60Hz
Edition: 10.12.2004
Please download latest version from
www.erco.com/88045.023
1/1
SP2
Varianti
Varianti is an adjustable
recesses downlight trim series
available for MR-11 and MR-16
lamps. The trim is made from three
precision-machined metal rings.
This three ring construction makes
for easy re-lamping and ideal heat
dissipation. A spring tension lamp
holder insures positive lamp
placement and allows the use of
two optional lenses and louvers at
the same time. Machined aluminum
trims are powder coat painted
white, black and metallic silver.
Machined brass trims are plated
chrome, matte aluminum, black
nickel and polished natural brass.
Consult factory for custom colors
or finishes.
Specifications:
Rotating center ring pivots 35 degrees in either direction, capable of utilizing two (2) media accessories in
conjuction with one MR-11 or MR-16 lamp. Snapin/Pull-out center ring assembly provides convenient
lamp servicing.
UL and cUL Listed for use with Ardee Lighting A35
series low-voltage rough-in downlight housings.
Suitable for use in damp locations.
Lamp: Enclosed MR-11, 12 volt, or open MR-11 12 volt
lamp and added protective lens. 35 watts maximum.
Enclosed MR-16, 12 Volt, or open MR-16 12 volt lamp
and added protective lens. 50 watts maximum.
Varianti MR-16: Matte Aluminum
Black
Black Nickel
Polished Chrome
Polished Brass
Matte Aluminum
Metallic Silver
White
w/ Honeycomb Louver
MR-11: DL20 Series
MR-16: DL21 Series
low voltage recessed downlight trim series
low voltage recessed downlight trim series
DL20BK
DL20BN
DL20MA
DL20MS
DL20PC
DL20PB
DL20WH
Varianti w/ MR-11 black
Varianti w/ MR-11 black nickel
Varianti w/ MR-11 matte aluminum
Varianti w/ MR-11 metallic silver
Varianti w/ MR-11 polished chrome
Varianti w/ MR-11 polished brass
Varianti w/ MR-11 white
DL21BK
DL21BN
DL21MA
DL21MS
DL21PC
DL21PB
DL21WH
Varianti w/ MR-16 black
Varianti w/ MR-16 black nickel
Varianti w/ MR-16 matte aluminum
Varianti w/ MR-16 metallic silver
Varianti w/ MR-16 polished chrome
Varianti w/ MR-16 polished brass
Varianti w/ MR-16 white
UL Listed with Rough-ins
A35R-120
A35R-12
A35S-120
A35S-12
A35I-120
Remodel rough-in, 50 watt max.
Remodel rough-in for remote transformer, 50 watt max.
Standard rough-in, 50 watt max.
Standard rough-in for remote transformer, 50 watt max.
IC rough-in, 35 watt max.
Consult factory for complete rough-in product offering
ø4.375"
5.25"
VISION
RAIL
color
stem
lamp
watts
AB prismatic multicolor
AM amber
RB bordeaux
BU blue
CR clear
GR green
PR lavender
1A MR11
mount
35
TR1
MRL monorail
MR2 2-circuit rail
MPT monopoint
Optically pure Swarovski crystals elegantly illuminated
by halogen light. Mounts up or down.
model
choose your options,
build your model #.
01" straight
HA336 CR 01 1A 35 MRL
(4) RAIL-ST-SC48" or 96"
(1) XCONNECTORSC-M
(4) RAIL-ST-SC48" or 96"
(4) ACONNECTORSC-M
(4) TCONNECTORSC-M
(1) XCONNECTORSC-M
(4) RAIL-ST-SC48" or 96"
(4) ACONNECTORSC-M
(3) RAIL-ST-SC48" or 96"
(3) ACONNECTORSC-M
(2) RAIL-CV-1 or CV-2
(2) ACONNECTORSC-M
24" diameter:
(3) RAIL-CV-SC62.5
(3) SCONNECTORSC-M
48" diameter:
(3) RAIL-CV-SC125
(3) SCONNECTORSC-M
78" diameter:
(5) RAIL-CV-SC117
(3) SCONNECTORSC-M
(2) RAIL-ST-SC48" or 96"
(1) ACONNECTORSC-M
RAILCV2-SC125
40.50"
RAIL-ST-SC48" OR RAIL-ST-SC96"
47.25"or 94.5"
RAILCV1-SC117
Straight Rail
RAILCV3-SC62.5
Soft Curve
78" Diameter, 1⁄5 Round, Radius 39"
Order 5 pieces to create a 78" diameter circle.
46"
48" Diameter Circle
1
⁄3 Round, Radius 24"
Order 3 pieces to create a 48" diameter circle,
or use our 48" Circle Kit.
20"
24" Diameter Circle
1
⁄3 Round, Radius 12"
Order 3 pieces to create a 24" diameter
circle,or use our 24" Circle Kit.
TR1
UC1
Type
Catalog Number
FEATURES
• Trim, low-profile design, only 1-3/16" deep.
• Flattened knockouts for cleaner appearance.
• Snap-fit channel cover attachment. No tools required for wireway access.
• Hinged, removable channel cover allows hands-free wiring and
quick installation.
• Factory-installed starters on all preheat models.
• Romex/BXR conduit connector provided with each fixture.
• Optional instant-on electronic start magnetic ballast for flickerfree lamp start.
• Low-brightness, linear prismatic diffuser provides improved visual comfort.
• 15% DR acrylic and snap-fit diffuser design for improved shatterresistant and positive attachment.
• Optional task diffuser with clear linear prismatic bottom and
opaque front for maximum illumination without direct edge glare.
• Five fixture lengths available.
• Available with factory-installed lamp, switch, cordset and convenience outlet options.
Catalog number
Type
.....................................
...................................................................................................................
.....................................
...................................................................................................................
.....................................
...................................................................................................................
Undercabinet Light
UC
1" Wrap-Front Lens
SPECIFICATIONS
BALLAST — Normal power factor reactor type ballast standard.
Others available (See ordering information).
WIRING & ELECTRICAL — Fixture conforms to UL 1570 and is suitable for damp locations. AWM, TFN or THHN wire used throughout, rated for required temperatures.
MATERIALS — Metal parts precision roll-formed from 20 gauge
cold rolled steel.
FINISH — Five-stage iron-phosphate pre-treatment ensures superior paint adhesion and rust resistance. Painted parts finished
with polyester powder paint.
LISTING — UL listed and labeled. Listed and labeled to comply
with Canadian and Mexican Standards.
Specifications subject to change without notice.
PHOTOMETRICS
Photometry derived in accordance with IESNA LM41 procedure. Vertical and horizontal illuminance is
calculated with fixture mounted 15" from work surface. Full photometric data available upon request.
Initial Point Illumination on horizontal work surface. (fc)
Coordinates are on 6" centers.
UC 24
Report LTL 6349
A
B
C
D
E
F
G
H
1
7
13
21
26
26
21
13
7
2
9
19
30
38
38
30
18
9
3
9
18
29
36
36
29
18
9
4
7
13
19
23
23
19
13
7
5
5
8
10
12
12
10
8
5
6
3
4
6
7
7
6
4
3
UC 42
Report LTL 6447
A
B
C
D
E
F
G
H
1
2
3
4
5
6
22
32
37
40
40
37
32
22
31
46
54
58
58
54
46
31
31
44
52
56
56
52
44
31
21
30
35
37
37
35
30
21
13
17
19
21
21
19
17
13
7
9
11
12
12
11
9
7
COMMERCIAL & INDUSTRIAL FLUORESCENT LIGHTING
UC
UC1
UC Undercabinet Light
MOUNTING DATA
DIMENSIONS
For unit or row mount installation, surface mounting only.
Inches (centimeters). Subject to change without notice.
K.O. BOTH
ENDS OF PART
5/8
(1.59)
7/8
Length
A
B
C
# Keyholes
12-3/8 (31.43)
7-1/16 (17.94)
2-5/8 (6.67)
6-1/8 (15.56)
2
21-3/8 (52.23)
16-1/16 (40.80)
2-5/8 (6.67)
10-11/16 (27.15)
2
24-1/2 (62.25)
19-1/4 (48.90)
2-5/8 (6.67)
12-1/4 (31.12)
2
33-1/2 (85.10)
28-1/4 (71.76)
2-5/8 (6.67)
17 (43.18)
2
42-1/2 (107.96)
37-1/4 (94.62)
2-5/8 (6.67)
21-1/4 (53.98)
2
(2.22)
9/16
(1.43)
1-3/16
(3.02)
5/8
(1.59)
5
(12.7)
L
3/8
dia.
(1.02)
5/8
dia. K.O.
(1.59)
7/16
(11.11)
3/8
(1.02)
C
3/16
dia.
(.48)
3-15/16
(8.41)
1 (2.54)
7/8
dia. K.O.
(2.22)
Keyhole Slot
A
B
ORDERING INFORMATION
Example: UC 33K OP 120
UC
Series
UC Undercabinet
light
Fixture length/ballast type
12
12K
21
21K
24
24K
33
33K
42
42K
(1) 8W T5, Preheat
(1) 8W T5, Instant-On
(1) 13W T5, Preheat
(1) 13W T5, Instant-On
(2) 8W T5, Preheat
(2) 8W T5, Instant-On
(1) 8W and (1) 13W T5, Preheat
(1) 8W and 13W T5, Instant-On
(2) 13W T5, Preheat
(2) 13W T5, Instant-On
UC
© 1997 Lithonia Lighting, Rev. 8/99
UC.P65
Diffuser
Voltage
(blank) Standard, milk-white,
DR acrylic
OP Opaque-front, clear
bottom DR acrylic
120, 277
Options
GLR Internal fast-blow fuse
GMF Internal slow-blow fuse
CSW 6-foot, 3-wire, grounded cordset,
right end
LPWW Warm white 3000K T5 lamp(s);
factory supplied
VALREF213 Electronic ballast
PAF White powder paint finish after
fabrication
CO Grounded convenience outlet.
Installed, bottom right, 120V only
SWR Rocker switch, installed bottom
right, 120V only
CSA Listed and labeled to comply with
Canadian Standards
NOM Listed and labeled to comply with
Mexican Standards
COMMERCIAL & INDUSTRIAL FLUORESCENT LIGHTING
P.O. BOX A, CONYERS, GEORGIA 30012, TELEPHONE 770-922-9000, FAX 770-929-8789
www.lithonia.com IN CANADA: 1100 50TH AVE., LACHINE, QUEBEC H8T 2V3
E
WW1
Fluorescent wallwasher
6"
152 mm
for fluorescent lamps
15 9/16"
395 mm
6 3/8"
162 mm
CO 46 7/16" x 5 5/16"
CO 1180 x 150 mm
55 7/8"
1419 mm
F28T5
Lä ö B
Dry Damp Wet
ÄIndoor
65040.023
Reflector color Silver
F28T5 28W Min. Bipin 2900lm
ECG
Product description
Housing: metal, white (RAL9002)
powder-coated.
Electronic control gear 120V/277V,
60Hz, class P inside cast housing.
Mounting plate for preinstallation
with junction box for throughwiring, black powder-coated. Snapin plug for connection between
junction box and luminaire.
Wallwasher reflector: aluminum,
silver, satin matt anodized. Hinged
cover for lamp replacement.
Type Non IC luminaire.
Insulation materials must be kept
away from the luminaire by a minimum of 3". Suitable for damp
location. Removal of reflector allows access to junction box from
below.
Max. ceiling thickness 3/4".
Weigth: 17.64 lbs / 8.00 kg
ERCO Lighting, Inc.
160 Raritan Center Parkway
Suite 10
Edison, NJ 08837
USA
Tel.: +1 732 225 8856
Fax: +1 732 225 8857
[email protected]
Wallwash information
F28T5 28W Min. Bipin 2900lm
Distance
from
ceiling
(Feet)
0
1
2
3
4
5
6
7
8
9
10
3.00’ from wall
5.00’ O.C.
3.00’ from wall
6.00’ O.C.
4.00’ from wall
5.00’ O.C.
4.00’ from wall
6.00’ O.C.
Below
Fixture
0
36
53
40
30
22
17
13
10
8
6
Below
Fixture
0
34
49
36
26
19
14
11
8
7
5
Below
Fixture
0
16
35
34
28
23
19
15
12
10
8
Below
Fixture
0
14
31
30
25
20
16
13
10
8
7
Between
Fixtures
0
25
41
34
26
20
15
11
8
7
5
Between
Fixtures
0
19
31
27
22
17
13
10
7
6
5
Between
Fixtures
0
13
30
30
25
20
16
13
10
8
7
Between
Fixtures
0
10
24
25
21
17
14
11
9
7
6
All vertical footcandles include the light loss factor of 0.8 with no contribution from ceiling or floor reflectances. Computation performed with a total of five wallwashers.
Technical Region: 120V/60Hz
Edition: 10.12.2004
Please download latest version from
www.erco.com/65040.023
1/1
WW2
Wall/Slot®-2000
Wall/Slot®-2000PR
2000 or 2000PR
Recessed Perimeter
Specifications
Wall/Slot-2000
FIXTURE SUPPORT RAIL. Extruded white aluminum, wall-mounted rail provides continuous support
and true alignment of fixtures and components. Rail is designed to provide reveal and compensate for
irregularities in wall construction. Galvanized spline keys are included for continuous alignment.
FIXTURE HOUSING. Die-formed and welded 20-gauge steel. Plenum cover/wall bracket is a one-piece
assembly of 20-gauge steel and heavy-gauge steel brackets with leveling screws to provide adjustment.
Brackets are spaced approximately every two feet for 2-, 4-, and 8-foot fixtures, and 1 1/2 feet for 3-foot and
6-foot fixtures. Plenum cover has a continuous hook-and-lock feature for quick installation.
REFLECTOR. 2000 Curved reflector is die-formed specular hammertone aluminum, precisely shaped for
maximum downward light projection. Straight reflector portions are steel, finished in high-reflectance
white for uniform light distribution. 2000PR Parabolic reflector (PR) is die-formed low-iridescence
semi-specular aluminum, precisely shaped for maximum downward light projection. It is shielded from all
viewing angles from 0° to 60° below horizontal. Straight reflector portions are steel, finished in high-reflectance
white for uniform light distribution.
CEILING TRIM/LUMINANCE CONTROL DEFLECTOR. Extruded aluminum with internal aligner splines.
LCD shields lamps from direct view and eliminates socket shadows on wall. Paint finish is CWM (Matte
White) baked enamel.
BALLAST. Electronic, high power factor, thermally protected Class P, Sound Rated A, manufactured by a UL
Listed manufacturer, as available, determined by Litecontrol. The minimum number of ballasts will be used.
CEILING TYPE. Compatible with most types of ceiling systems, including grid and plaster. Fixture system
must be installed prior to installation of ceiling. Finish of wall should extend 13” above finished ceiling height.
See Wall/Slot-2000 Pre-Installation Manual for specific ceiling type details.
CERTIFICATION. Fixture and electrical components shall be UL and/or CUL Listed and shall bear the
I.B.E.W., A.F. of L. label.
�� ���� �����
� ����
����
����
����
��
�����
��
�����
Wall/Slot-2000PR
�� ���� �����
� ����
����
����
����
��
�����
��������� ���������
Note: Litecontrol reserves the right to change specifications without notice for product development and improvement.
��
�����
Ordering guide
Product, Lamping, & Length
Options
20
1
4
T8 -
CWM
ELB -
PR -
120
Series
Lamp
Count
Nominal
Length
(ft)
2
3
4
6
8
3
4
6
8
2
4
8
3
6
Lamp
Type
Color
Ballast
Option
Volts
one-lamp (1 lamp in cross-section), 4-foot long T8 fixture with
parabolic reflector, painted Matte White, electronic ballast, 120 volts.
T8
CWM
(Matte
White)
ELB
ELB10
DA-ELB
HEL/ELB
ECO/ELB
EF
F
SDS
PR
120
277
notes: Lamp Count = the total number of lamps in fixture
see
Options
Cross-section lamping
1
1
1
2
2
1
1
2
2
1
2
4
2
4
see
notes
T5HO
T5
-
see
Ballast
options
2014T8-CWM-ELB-PR-120 is a typical catalog number for a
For Ordering guide information in shaded areas, choose selection by
reading ACROSS the shaded areas for correct specifications.
2000
BX40
BX39
1-T8
1-T5 or 1-T5O
Questions to Ask
1. 120 or 277 volt? 2. Row information, including desired fixture lengths?
3. Verify ceiling type? 4. Other options?
110
2000PR
BX40
1-T8
1-T5 or 1-T5HO
BX40
www.litecontrol.com
12-9/16"
(319mm)
Small semi-recessed with hood
D
A
B
C
E
F
H
1:8 Scale (Quad tube fluorescent, metal halide integral) *
6-7/8"
(175mm)
1:8 Scale (Tungsten halogen, metal halide remote)
Lighting the Wall
Style 201
3-1/8"
(79mm)
2"
(51mm)
Style 205
3-3/4"
(95mm)
J
K
D Spring clips (4 incl.)
E Micro-prismatic
tempered glass lens
(tungsten halogen and
metal halide units)
Die-cast aluminum hood
F
G
A
D
E
F
H
K
L
(below ceiling)
Quad Tube
Compact Fluorescent
Profile
2"
(51mm)
6-7/8"
(175mm)
Ceiling Cutout
12"
(305mm)
Ceramic
Metal Halide
K Snap-in polycarbonate
cross baffle (matte
gray), 15° shielding
(quad tube only)
L Twist and lock
lampholder (quad tube)
6-1/4"
(160mm)
G Supplemental wire
supports (by others)
H Integral ballast with splice
compartment (Style 205)
Specular extruded
aluminum reflector
Electrical:
Use 90°C wire for supply connections.
Style 201 (halogen, metal halide remote) - 5' (1.5m) wire leads
in flexible conduit exit back box for connection to accessible
junction box (by others), or to remote ballast (installation prior
to finished ceiling recommended).
Style 205 (quad tube, 35W/70W metal halide integral) - splice
compartment with two 7/8" diameter conduit entries.
Tungsten halogen - DC bayonet or RSC lampholders in
patented clamping supports for maximum heat dissipation.
Fluorescent - integral HPF thermally protected electronic
ballast with end-of-life protection. Optional electronic
dimming ballast dims to 5% of full light output. Compatible
dimmer switch required (by others).
Metal halide - Style 201 remote: encapsulated high reactance
autotransformer (HX-HPF) ballast. Optional remote electronic
ballast for 150W. Style 205 integral (35W, 70W only):
electronic ballast provides improved voltage regulation and
color stability.
For complete ballast specifications, see Accessories Section.
J
* Diagram shows Style 205 for quad tube fluorescent. Snap-in baffle provided for quad tube only.
Style 205 for metal halide is provided with lens as shown in upper Style 201 diagram.
Specifications
A Extruded aluminum
mounting / trim frame
B Conduit connector
(Style 201)
C Aluminum back box
Finish:
Semi-gloss white hood and ceiling trim. Black back box.
Painted surfaces - 6 stage pretreatment and electrostatically
applied thermoset powder coat.
Reflector - extruded high purity aluminum with clear anodized
specular finish. All luminaire hardware - stainless steel.
Mounting:
Mounting / trim frame installs from below finished ceiling.
Retrofits into existing non-accessible ceilings.
Spring clips provided for rigid ceilings (drywall, plaster) up to
1-3/4" (44mm) thick.
Supplemental support wires, bar hangers, etc. (by others)
required for accessible ceilings. Where wire suspension is
prohibited, order accessory universal mounting brackets for
use with 1/2" EMT, 1-1/2" lathing or C channel (by others).
Standard:
UL listed or CSA certified for damp locations. (TH and MH
units with lens recommended for damp location use.)
Minimum spacings for 200W/250W Style 201, all Style 205:
2' (0.6m) on center, 1' (0.3m) fixture center to side wall,
3" (76mm) to overhead building member.
REV. 11/02
Tungsten Halogen
Features
luminous wall, not the luminaire
Style 201 / 205
■ Low profile - minimal silhouette focuses attention on the
■ Evenly lights entire wall - reflector aperture is shielded
■ Shallow recessed depth - fits under ducts at core walls
die-cast hood, aluminum back box
■ Durable construction - extruded reflector and trim frame;
Performance
1400
Cd
70W
MH
35W
MH
3000
Cd
Two parabolic reflector sections drive light to the bottom of the
wall. An elliptical section shields the lamp from normal viewing
angles and redirects its light to a parabola. Glare is minimized
and asymmetry of the beam is maximized resulting in high
beam efficiency and superior surface uniformity.
26W
QUAD
150W
TH
For complete photometrics, visit www.elliptipar.com.
elliptipar
WW3
W
17.0
W
17.1
To Order
3
4
5
-T -0 2 -
To form a Catalog Number
2
6
7
8
Ballast**
Distance+
Project:
Type:
Style 201 / 205
Accessories
■
= Ballast fuse kit
0 = UL
J = CSA
The external shapes of the asymmetric reflectors are trademarks of elliptipar.
Certain products illustrated may be covered by applicable patents and patents pending.
For a list of patents, see Contents pages. These specifications supersede all prior
publications and are subject to change without notice. © 2004 elliptipar.
AFK000X
ASRBKT00 = Universal mounting brackets (set of two),
accepts 1/2" EMT,
1-1/2" lathing, C channel
or bar hangers
(by others)
AUV00030 = Ultraviolet (UV) filter glass lens
(tungsten halogen and
metal halide units only)
4 Mounting
Compact Fluorescent &
Metal Halide Electronic*
(Style 205)
1 = 120V
2 = 277V
3 = 347V (Canada)**
Order separately. See Accessories Section for specifications.
Tungsten Halogen
(Style 201)
A = 120V
Metal Halide Magnetic
(Style 201)
A = 120V
B = 277V
H = 347V (Canada)+
(See Accessories Section for specifications)
■
elliptipar
114 Boston Post Road, West Haven, Connecticut 06516, USA
Voice 203.931.4455 Fax 203.931.4464 www.elliptipar.com
Small semi-recessed with hood for use with 35W metal halide
lamp. Overlapping ceiling trim. Semi-gloss white. Integral
120V electronic ballast. UL.
M205 - 035G - T - 02 - 1 - 000
Example
0 = UL, Underwriters Laboratories
J = CSA, Canadian Standards Association
8 Standard
00 = No options
0C = Style 201 modified to comply with Chicago plenum
code. Not available for Style 205 integral units.
0E = Style 205 remote emergency battery pack for quad
tube fluorescent. Maximum distance from battery pack
to fixture is 5' (1.5m). For use with non-dimming
ballasts only.
0H = Style 201 long distance remote metal halide ballast
(encapsulated HX-HPF magnetic ballast only),
35W: 15' min. up to 50’ max. (4.5m - 15m),
70W: up to 50' max. (15m),
150W: up to 50’ max. (15m)
0Y = Style 201 modified to comply with New York City code.
(Style 205 integral complies as is without modification.)
XX = For modification not listed, include detailed description.
Consult factory prior to specification.
7 Option
+Not available for 35W metal halide.
* Electronic ballast for 35 and 70W available in Style M205 integral
only; for 150W in Style M201 remote only.
**Electronic 347V available for quad tube compact fluorescent only.
Compact Fluorescent
Dimming (Style 205)
T = 120V
V = 277V
T = Overlapping trim
5 Finish
1
1 Source
02 = Semi-gloss white
Voltage(s)
Integral
6 Voltage/Ballast
F = Quad tube compact fluorescent
M = Metal halide
T = Tungsten halogen
2 Style
Lamp
Number
Electr.
Dimming
HX-HPF 10' (3m)
Electr.
Integral
HX-HPF 20' (6m)
Electr.
Integral
HX-HPF 10' (3m)
Electr. 15' (4.5m)
1, 2, 3
T, V
201 = Small semi-recessed with hood, remote ballast
Note: Available for tungsten halogen (no ballast)
and metal halide only.
205 = Small semi-recessed with hood, integral ballast
Note: Available for quad tube compact fluorescent and
35W & 70W metal halide electronic only.
3 Lamp
Lamp WattCode age
Quad Tube Fluorescent
26
P126 (4-pin) CFQ26W/G24q
150 CMH150/T6/G12
A
A
A
A
Ceramic Metal Halide*
A, B
035G 35 CMH35/T6/G12
1, 2
A, B, H
070G 70 CMH70/T6/G12
1, 2
A, B, H
1, 2
150G
Tungsten Halogen
0100 100
Q100DC
0150 150
Q150DC
0200 200
Q200T3
0250 250
Q250DC
elliptipar
For complete lamp and ballast information, see Accessories Section.
Standard quad tube lamp color is 3000K / 80+ CRI.
* Metal halide lamps using ceramic arc tubes yield higher light output
than lamps with quartz arc tubes. They offer improved lamp-to-lamp
color consistency and a more stable color temperature over their
life (±200K). Standard lamp color is 3000K / 80+ CRI.
**Metal halide - magnetic (HX-HPF) ballast available in Style M201
remote only. Electronic ballast for 35 and 70W available in Style
M205 integral only; for 150W in Style M201 remote only.
+Distance applies only to Style M201 remote magnetic ballasts (and
remote electronic ballast for 150W).
REV. 4/04
WW3
UL
SPECIFIER GUIDE
R
PRODUCT
DESCRIPTION
LISTED
PRODUCT
C O D E
CURVABLE LOW VOLTAGE HALOGEN STRIPLIGHT
CHANNELITE BOL 6000 QHX
DRAWING NO. CL 119
C COPYRIGHT 2004
• Ideal for wall wash or task lighting in curved spaces
• Uses high-performance ALR lamps for precise effect
• Also uses MR lamps (Refer to CL 119-A)
• Twist & lock DC bayonet base for safe lamping in lamp-down applications
• Listed for damp location
• Dimmable
3 1/4”
2”X 2”
ALUMINUM HOUSING
2”
INTEGRAL
DOUBLE CONTACT
TRANSFORMERS FLEXIBLE JOINER
BAYONET BASE
LAMPHOLDER
1/2 “ CONDUIT
(SPECIFY SWIVEL OR FIXED)
( BY CONTRACTOR )
ALR 56mm
ALR 37mm
4”
2”
2”
HALOGEN
MR LAMP
SPECIFY SPACING
SPECIFY TOTAL
LENGTH OF RUN
SEE BELOW FOR MINIMUM INSIDE RADIUS
BOL 19
BLANK END CAP
RECOMMENDED LAMPS
TYPE : ALR LAMP
BASE : DC BAYONET BASE (B15d)
BRAND : PHILIPS
CODE
WATTS
ALR-37
20 W
ALR-56
50 W
WW5,WW6
END VIEW
BOL 6000 QHX
BOL 20
KNOCK OUT END CAP
2”
QUICK REFERENCE INSTALLATION INSTRUCTIONS
1. Remove cover piece from module, by removing screws and using
flathead screwdriver to pry open.
2. Screw mount bottom piece directly onto secure surface.
3. Snap cover piece into bottom piece and replace screws.
4. To continue run, attach and mount next module and make electrical
connections.
5. Attach end caps at beginning and end of run, sliding base plate
into bottom piece and securing with screw.
6. Connect lead wires at beginning of run to power source and
ground. Do not power until installation complete.
7. Insert lamps.
END VIEW
COVER
40
AVG. CENTER
BEAM
ANGLE CANDLE POWER
6
7000 cd
18
1000 cd
32
400 cd
10
13000 cd
25
1900 cd
RATED
HRS.
4000
4000
4000
4000
4000
COLOR
TEMP.
3000 K
3000 K
3000 K
3000 K
3000 K
BOTTOM
END CAP
BASE PLATE
With swivel socket, lamp
swivels front and back 40
LAMPS NOT INCLUDED
SS PP EE CC II FF II CC AA TT II OO NN SS
PRODUCT CODE
BOL 6000 QHX
LAMPHOLDER
S
F
Swivel
VOLTS
12V
LAMP TYPE
ALR-37
ALR-56
Fixed
Or specify MR
lamp ( Refer to
CL 119-A )
LAMP SPACING & RADIUS
6” o.c.
TRANSFORMER
6” on center ( 13” minimum inside
radius )
12” o.c. 12” on center ( 28” minimum inside
radius )
I
R
FINISH
Integral
NAL
Natural aluminum
Remote
(Consult factory )
SAT
Anodized satin
Or specify other
Specify other
EXAMPLE
BOL 6000 QHX
S
12V
ALR-37
6” o.c.
I
NAL
FILL OUT BELOW FOR SUBMITTAL
BOL 6000 QHX
12V
PROJECT
NAME
SPECIFIER
FIXTURE
SCHED. TYPE
CONTRACTOR
QUANTITY
DISTRIBUTOR
LENGTHS
REPRESENTATIVE
visit us at :
w w w. c e l e s t i a l l i g h t i n g . c o m
e•mail :
info @ celestiallighting.com
14009 Dinard Ave.
Santa Fe Springs,
CA 90670
PH (562)•802•8811
(800)•233•3563
FX (562)•802•2882
FD1,FD2,FD4,FD5,FD5b
FP1, FP2,WW1,FC2
28W/830 Min Bipin T5 UNP
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product Number
230847
Full product name
28W/830 Min Bipin T5 UNP
Ordering Code
F28T5/830
Pack type
Unpacked
Pieces per pack
1
Packs per case
40
Pack UPC
046677230845
EAN2US
-
Case Bar Code
50046677230840
Successor Product number
-
Wattage[W ]
28W
Color Code
830 [CCT of 3000K]
Base
Min Bipin [Miniature Bipin]
Bulb
T5 [Diameter: .625 inch]
Packing Type
UNP [Unpacked]
System Description
High Efficiency
Base Information
Green Plate
Packing Configuration
40
Rated Avg. Life[hr ]
24000
Dimmable
Yes
Color Rendering Index[Ra8 ]
85
Color Designation
Warm White
Color Description
830 Warm White
Color Temperature[K ]
3000
Initial Lumens[Lm ]
-
Overall Length C[mm ]
1163.2
Diameter D[mm ]
17
Page 1 of 2
WW3
SC1
24W/830 Min Bipin T5 HO UNP
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product Number
290197
Full product name
24W/830 Min Bipin T5 HO UNP
Ordering Code
F24T5/830/HO
Pack type
Unpacked
Pieces per pack
1
Packs per case
40
Pack UPC
046677290191
EAN2US
-
Case Bar Code
50046677290196
Successor Product number
-
Wattage[W ]
24W
Color Code
830 [CCT of 3000K]
Base
Min Bipin [Miniature Bipin]
Bulb
T5 [Diameter: .625 inch]
Packing Type
UNP [Unpacked]
System Description
High Output
Base Information
Green Plate
Packing Configuration
40
Rated Avg. Life[hr ]
24000
Dimmable
Yes
Color Rendering Index[Ra8 ]
85
Color Designation
Warm White
Color Description
830 Warm White
Color Temperature[K ]
3000
Initial Lumens[Lm ]
-
Overall Length C[mm ]
563.2
Diameter D[mm ]
17
Page 1 of 2
SP2,WW6
Aluline Pro 20W 12V R37 18D FR 1CT
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product number
340026
Full product name
Aluline Pro 20W 12V R37 18D FR 1CT
OrdCodUS
-
Pack type
1 Lamp in a Folding Carton
Pieces per pack
1
Packs per case
50
EAN1US
-
EAN2US
-
EAN3US
-
Successor Product number
-
Lamp Wattage Rated[W ]
20W
Voltage[V ]
12V
Bulb
R37 [R 37mm]
Beam Angle[D ]
18D
Bulb Finish
FR [Frosted]
Packing Type
1CT [1 Lamp in a Folding Carton]
Packing Configuration
10X5F
ANSI Code Halogen
GBE
Cap-Base
BA15d
Cap-Base Information
na[-]
Operating Position
any[Any or Universal (U)]
Life to 50% failures[hr ]
2000
Dimmable
Yes
Luminous Intensity[cd ]
-
Colour Rendering Index[Ra8 ]
100
Colour Temperature[K ]
3000
Overall Length C[mm ]
41
Diameter D[mm ]
38
Page 1 of 2
FS1
14W/830 Min Bipin T5 UNP
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product Number
230771
Full product name
14W/830 Min Bipin T5 UNP
Ordering Code
F14T5/830
Pack type
Unpacked
Pieces per pack
1
Packs per case
40
Pack UPC
046677230777
EAN2US
-
Case Bar Code
50046677230772
Successor Product number
-
Wattage[W ]
14W
Color Code
830 [CCT of 3000K]
Base
Min Bipin [Miniature Bipin]
Bulb
T5 [Diameter: .625 inch]
Packing Type
UNP [Unpacked]
System Description
High Efficiency
Base Information
Green Plate
Packing Configuration
40
Rated Avg. Life[hr ]
24000
Dimmable
Yes
Color Rendering Index[Ra8 ]
85
Color Designation
Warm White
Color Description
830 Warm White
Color Temperature[K ]
3000
Initial Lumens[Lm ]
-
Overall Length C[mm ]
563.2
Diameter D[mm ]
17
Page 1 of 2
UC1
WW5
Aluline Pro 20W 12V R37 6D CL 1CT
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product number
328401
Full product name
Aluline Pro 20W 12V R37 6D CL 1CT
OrdCodUS
-
Pack type
1 Lamp in a Folding Carton
Pieces per pack
1
Packs per case
50
EAN1US
-
EAN2US
-
EAN3US
-
Successor Product number
-
Lamp Wattage Rated[W ]
20W
Voltage[V ]
12V
Bulb
R37 [R 37mm]
Beam Angle[D ]
6D
Bulb Finish
CL [Clear]
Packing Type
1CT [1 Lamp in a Folding Carton]
Packing Configuration
10X5F
ANSI Code Halogen
GBD
Cap-Base
BA15d
Cap-Base Information
19
Operating Position
any[Any or Universal (U)]
Life to 50% failures[hr ]
2000
Dimmable
Yes
Luminous Intensity[cd ]
-
Colour Rendering Index[Ra8 ]
100
Colour Temperature[K ]
3000
Overall Length C[mm ]
41
Diameter D[mm ]
38
Page 1 of 2
SC3,GR1,GR2
!
"
#
!$
%&
'
#
#
!
#
!$
!
%
%
%(
*+
)
(,
-
. )
,
!
$/ 0
/
1
20
-
/#
%#
!$ &
%#
!$
-
!1
#
$
#
!
#
!#5
#
!$
7
+6$4'#
1/
5 0
,&
##!
8
9
(!#
6
/
(!#
6
*'/ 0
$/
90
#
7!
#
!$:
! ;/
7
#
$! #!
5#
/
20
:
!## '
!/
' 0
' !$ 5 /
0
5#
# #!
"6
#
!$
#!
"
'
34.#
! 50
/ '
0
0
!0
SC5
!
"
#
$
#%
&
) *"
$
'
+
"
(
,
"# #
--
1
" )
) "
)'
--
'+
.
/
0
+
#
.
%2 3
/
2
4
2
$ 3
/
2$
/
!$
#$7
2
!
/
9
#4
$#
/
$
"
$
#%
$$#
;
/
2
/
/
&
:
"<
3
,
"# #3
-6
10
&9
1
%2
<3
;#
$
#%9
# =2
;
$
%# $#
"
3
0
7$
2
(3
3
2
'#$
,
-
$
%7 2 %3
+9
83
$#
,%6 $
42
7 3
*
2
+2 +
#4
$
%
5 6 0$
# 73
3
'#$
,
)$
#% *"
)$
#%
(3
P1
!"
# $% %
&'
!
#
*
&*
*
)
$
&+
,
)- $+#
.
*
#
(
&
,
**
.
"/ 0
*
/
! 0
/!
!!
*3
/
* 4
!
!"
5
*!!
#/ #
&!"
!
"
!
$
-("2 ! /
3 0
'
- #4
9
!
"3 / "0
$2
54
:
"/
:0
8
!"4
*!
"
4 !!
*!
"
#$
$
/
8 90
!
7
*/
**
*0
6 **
+!
( * /
+!
( * 0
&!"7'
8
0
**/
!
1$2$ ! 30
/
;0
$$
0
,
*/
0
<
(
) 0
FP4,FC1
SITE SEARCH
HOME
PRODUCTS
EDUCATION / RESOURCES
Product Search
LIGHTING APPLICATIONS
Where to Buy | FAQs | Contact Us
T5 Starcoat High Output Item Detail
Home
Basic
Products
Fluorescent
T5 Starcoat High Efficiency
T5 Starcoat High Output
T5 Preheat
T8 Ecolux - TCLP
Compliant (2', 3', and 4') w/
Starcoat
Subcategory
T5 Starcoat High Output
Product Code
90232
Description
F54W/T5/830
Watts
54
Lumens (Initial)
5000
Lumens (Mean)
4700
Average Rated Life
20000
Color Temperature (K)
3000
Color Rendering Index (Ra) CRI
85
Bulb Type
T5
Base Type
Miniature BiPin (G5)
F25T12 for T8 Ballasts
Nominal Length (In.)
45.2
8' T8
Nominal Length (mm)
1150
Sales Unit UPC
043168902328
Case UPC
043168902328
Case Quantity
40
Additional Information
S/P Ratio: 1.3
T8 Ecolux XL and SXL (4')
Extra Life w/ Starcoat
T8 ULTRA Watt-Miser (4',
8', XL) w/ Starcoat
T8 ULTRA F28T8 UltraMax
System w/ Starcoat
T8 ULTRA High Lumen w/
Starcoat
T8 Mod-U-line®
8' T8 XL Extra Life
8' T8 Watt-Miser XL ExtraLife
8' T8 High Output
LSB Data Available
8' T8 Instant Start
T8 Other Lengths
T8 Preheat
3' T12 (F30T12 and
F25T12) - Rapid Start
F40 Standard Rapid Start
F40 XL Extra Life Rapid
Start
F48" Utility Shoplight
F40 Watt-Miser® (F34);
Set the current view to the default view
Return to product list
LSB
TR1,SC2
HOME
SITE SEARCH
PRODUCTS
EDUCATION / RESOURCES
Product Search
LIGHTING APPLICATIONS
Where to Buy | FAQs | Contact Us
Standard MR11 Item Detail
Home
Products
Halogen
Retail HIR™ PAR 38
HIR/XL (UltraLong Life)
PAR38
HIR™ PAR38
Subcategory
Standard MR11
Product Code
41484
Description
Q35MR11/CG30 24
Volts
24
Watts
35
Average Life in Hours
2000
CBCP
1300
Color Temperature (K)
2950
Bulb Type
MR11
Base Type
2-Pin G4
Compact PAR30 Long Neck
Max Overall Length (In.)
1.375
Compact PAR30
Max Overall Length (mm)
35
Filament Type
C-6
Sales Unit UPC
043168414845
Halogen Compact PAR16
Case UPC
043168414845
Diamond Precise™
Electronic MR16
Case Quantity
50
Additional Information
Floodlight
PAR36
Footnotes
WARNING
- Keep combustible materials away from lamp
- Use in fixture rated for this product
- Use in enclosed fixture rated for this product
- Do not use lamp if outer glass is scratched or broken
Silver Saver™ PAR38
Long Life PAR38
Halogen Plus PAR38
Standard Halogen PAR38
Cool Beam PAR38
Quartzline® PAR38
Compact HIR™ PAR30
Compact PAR20
A-Line/Decorative
Precise Cover Glass IR
MR16
CAUTION
- Allow lamp to cool before handling
- Do not use lamp if outer glass is scratched or broken
Turn & Lock
ConstantColor® MR16
ConstantColor® Precise™
Cover Glass MR16
ConstantColor® Precise™
MR16
Standard MR16
Standard MR11
120V MR16
Set the current view to the default view
Return to product list
C2
HOME
SITE SEARCH
PRODUCTS
EDUCATION / RESOURCES
Product Search
LIGHTING APPLICATIONS
Where to Buy | FAQs | Contact Us
Standard MR16 Item Detail
Home
Products
Halogen
Retail HIR™ PAR 38
HIR/XL (UltraLong Life)
PAR38
HIR™ PAR38
Subcategory
Standard MR16
Product Code
25481
Description
Q20MR16/SP
Volts
12
Watts
20
Average Life in Hours
2000
CBCP
3500
Color Temperature (K)
2900
Bulb Type
MR16
Base Type
2-Pin GX5.3
Compact PAR30 Long Neck
Max Overall Length (In.)
1.875
Compact PAR30
Max Overall Length (mm)
48
Filament Type
C-6
Sales Unit UPC
043168254816
Halogen Compact PAR16
Case UPC
043168254816
Diamond Precise™
Electronic MR16
Case Quantity
20
Additional Information
Spot, Replacement for ESX
PAR36
Footnotes
WARNING
- Keep combustible materials away from lamp
- Use in enclosed fixture rated for this product
- Use eye protection when handling lamp
- Use in enclosed fixture rated for this product
- Do not touch glass with bare hands
- Do not use lamp if outer glass is scratched or broken
Silver Saver™ PAR38
Long Life PAR38
Halogen Plus PAR38
Standard Halogen PAR38
Cool Beam PAR38
Quartzline® PAR38
Compact HIR™ PAR30
Compact PAR20
A-Line/Decorative
Precise Cover Glass IR
MR16
Turn & Lock
ConstantColor® MR16
CAUTION
- Allow lamp to cool before handling
-Turn power off before installing lamp
- Dispose of lamp in a closed container
- Do not use lamp if outer glass is scratched or broken
ConstantColor® Precise™
Cover Glass MR16
ConstantColor® Precise™
MR16
Set the current view to the default view
Standard MR16
Standard MR11
120V MR16
Return to product list
FD3,FP3
FC3
PL-L 40W/830 2G11/4P 1CT
| Save PDF | Open PDF
General
PRODUCT DATA
February 26, 2005
Product Number
300426
Full product name
PL-L 40W/830 2G11/4P 1CT
Ordering Code
PL-L 40W/830/4P RS/IS
Pack type
1 Lamp in a Folding Carton
Pieces per pack
1
Packs per case
25
Pack UPC
046677111786
EAN2US
-
Case Bar Code
50046677111781
Successor Product number
-
Wattage[W ]
40W
Color Code
830 [CCT of 3000K]
Base
2G11 [2G11]
Base Information
4P
Execution
/4P [4 Pins]
Packing Type
1CT [1 Lamp in a Folding Carton]
System Description
Rapid Start
Packing Configuration
25
Rated Avg. Life[hr ]
20000
Avg. Hrs. Life[hr ]
20000
Lamp Voltage[V ]
126
Dimmable
Yes
Color Rendering Index[Ra8 ]
82
Color Designation
Warm White
Color Description
830 Warm White
Color Temperature[K ]
3000
Initial Lumens[Lm ]
3500
Overall Length C[mm ]
542
Diameter D[mm ]
38
Diameter D1[mm ]
18
Page 1 of 2
WW2
ROP-2P32-SC
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
F17T8
F25T8
F25T8
* F32T8
F32T8
F32T8/ES (28W)
F32T8/ES (28W)
F32T8/ES (30W)
F32T8/ES (30W)
F40T8
F40T8
Num.
of
Lamp
s
2
1
2
1
2
1
2
1
2
1
2
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
17
25
25
32
32
28
28
30
30
40
40
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
60/16
60/16
32/00
32/00
0.26
0.23
0.37
0.30
0.47
0.25
0.41
0.28
0.44
0.35
0.56
Wiring Diagram
WHITE
BLACK
Input
Power
(ANSI
Watts)
31
27
43
35
55
30
48
33
52
41
67
OPTANIUM
Electronic
Instant Start
Parallel
120
50/60 HZ
Active
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
0.90
1.02
0.88
1.01
0.88
1.02
0.87
1.01
0.88
1.01
0.88
10
15
10
10
10
15
10
10
10
10
10
0.97
0.97
0.99
0.98
0.99
0.95
0.98
0.97
0.99
0.99
0.99
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
2.90
3.78
2.05
2.89
1.60
3.40
1.81
3.06
1.69
2.46
1.31
Enclosure
BLUE
BALLAST
BLUE
RED
LAMP
LINE
Diag. 68
Insulate unused blue
lead for 1000V
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Enclosure Dimensions
Standard Lead Length (inches)
Black
White
Blue
Red
Yellow
Gray
Violet
in.
25L
25L
31R
37L
0
0
0
cm.
63.5
63.5
78.7
94
0
0
0
Yellow/Blue
Blue/White
Brown
Orange
Orange/Black
Black/White
Red/White
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
OverAll (L)
9.50 "
9 1/2
24.1 cm
Width (W)
1.7 "
1 7/10
4.3 cm
Height (H) Mounting (M)
1.18 "
8.90 "
1 9/50
8 9/10
3 cm
22.6 cm
Revised 07/20/2004
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
UC1
RMB-2P13-S3-H
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
Num.
of
Lamp
s
CFQ13W/G24Q
2
CFQ18W/G24Q
1
CFT7W/2G7
2
CFT9W/2G7
2
CFTR13W/GX24Q
2
CFTR18W/GX24Q
1
* F13T5
2
F14T5
2
F8T5
2
F8T5 & F13T5
2
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
13
18
7
9
13
18
13
14
8
813
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0.23
0.13
0.14
0.17
0.23
0.13
0.24
0.24
0.16
0.20
Wiring Diagram
Input
Power
(ANSI
Watts)
27
15
16
20
27
15
28
28
19
23
MATCHBOX
Electronic
Instant Start
Series
120
60 HZ
Active
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
0.90
0.80
1.00
1.05
0.90
0.80
0.95
0.90
1.25
1.10
10
15
15
10
10
15
10
10
10
10
0.98
0.96
0.95
0.98
0.98
0.96
0.97
0.97
0.98
0.97
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
3.33
5.33
6.25
5.25
3.33
5.33
3.39
3.21
6.58
4.78
Enclosure
5.00"
4.01"
2.38"
2.0"
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Enclosure Dimensions
Standard Lead Length (inches)
Black
White
Blue
Red
Yellow
Gray
Violet
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
Yellow/Blue
Blue/White
Brown
Orange
Orange/Black
Black/White
Red/White
#6-20 thread forming
.25" long screws
0.116" holes
.17"
1.57"
.28"
.36"
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
OverAll (L)
5.0 "
5
12.7 cm
Width (W)
1.85 "
1 17/20
4.7 cm
Height (H) Mounting (M)
0.94 "
4.6 "
0 47/50
4 3/5
2.4 cm
11.7 cm
Revised 01/26/2004
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
FD5b
RCF-2S26-H1-LD-QS
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
CFQ26W/G24Q
CFQ26W/G24Q
CFTR26W/GX24Q
CFTR26W/GX24Q
* CFTR32W/GX24Q
CFTR42W/GX24Q
FC12T5
FC9T5
Num.
of
Lamp
s
1
2
1
2
1
1
1
1
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
26
26
26
26
32
42
40
22
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0.23
0.43
0.24
0.45
0.31
0.38
0.32
0.21
Wiring Diagram
BLUE
BLACK
WHITE
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
1.00
1.00
1.10
1.00
0.98
0.98
0.95
1.00
10
10
10
10
10
10
10
10
0.98
0.99
0.98
0.98
0.98
0.98
0.98
0.98
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
3.70
1.96
3.79
1.85
2.72
2.13
2.50
4.00
Enclosure
WIRING: (2) LAMPS
LINE
Input
Power
(ANSI
Watts)
27
51
29
54
36
46
38
25
SMARTMATE
Electronic
Rapid Start
Series
120
60 HZ
Active
(1) LAMP
BLUE
BALLAST YELLOW
GREEN
RED
RED
Green Terminal must be Grounded
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Standard Lead Length (inches)
Enclosure Dimensions
OverAll (L)
4.98 "
4 49/50
12.6 cm
Width (W)
2.4 "
2 2/5
6.1 cm
Height (H) Mounting (M)
1.0 "
4.6 "
1
4 3/5
2.5 cm
11.7 cm
Revised 09/02/2004
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
P1
High Pressure
Sodium
Lamp Ballast
Catalog Number 71A7927
For 70W
NONE
60 Hz R-NPF
Status: Active
DIMENSIONS AND DATA
2 5/8 X 2 3/16 CORE
4.00"
3.50"
0.75"
A
B
MAX.
0.30" WIDE
2 SLOTS
2.65"
2.20"
.20"
2.20"
4 HOLES
CLEARED
FOR #6
THRU-BOLTS
1.75"
.062"
.20"
Capacitor:
INPUT VOLTS
240
R-NPF
CIRCUIT TYPE
40%
POWER FACTOR (min)
REGULATION
Line Volts
±5%
Lamp Watts
WITHIN TRAPEZOID
LINE CURRENT (Amps)
Operating...................................................
0.98
Open Circuit...............................................
0.00
Starting......................................................
1.15
UL TEMPERATURE RATINGS
Insulation Class
H(180°C)
Coil Temperature Code
A
1029
MIN. AMBIENT STARTING TEMP.
-20°F or -30°C
NOM. OPEN CIRCUIT VOLTAGE
240
INPUT VOLTAGE AT LAMP DROPOUT...........................
190
INPUT WATTS
85
RECOMMENDED FUSE (Amps).....................................
3
CORE and COIL
Dimension (A)
1.50
Dimension (B)
2.80
Weight (lbs.)
2.5
Lead Lengths
.1"
CAPACITOR REQUIREMENT
Microfarads
Volts (min.)
Fault Current Withstand (amps)
60 Hz TEST PROCEDURES (Refer to Advance Test
Procedure for HID Ballasts - Form 1270)
High Potential Test (Volts)
1 minute
1500
2 seconds
2500
Open Circuit Voltage Test (Volts)
216-264
Short-Circuit Current Test (Amps)
Secondary Current
1.05-1.35
Input Current..............................................
0.95
1.45
-
-
-
-
Wiring Diagram:
LINE V
The capacitor is included as
part of the potted assembly.
LAMP
X3
IGNITOR
(OPTIONAL)
X1
X2
CAP
LAMP
COM
Fig. G
Ordering Information
Ignitor: LI501-H4
Order Suffix
Description
Ballast to Lamp Distance
(BTL) = 2 feet
Temp Rating: 105°C
Data is based upon tests performed by Advance Transformer in a controlled environment and representitive of relative performance.
Actual performance can vary depending on operating conditions. Specifications are subject to change without notice.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
06/04/03
FC1,FC2,FP1,FP2,FP4,WW1,FS1
Fluorescent Dimming Ballasts
Eco-10TM
10%
Lighting Management Dimming
Eco-10 (1) 07.06.04
Eco-10 Overview
Eco-10 lighting management electronic dimming
ballasts are designed to maximize the benefits of a
lighting management system. Eco-10 offers 100% to
10% dimming, and is ideal for use in any space where
saving energy is the primary goal of the design.
Eco-10, case type C
1.18”w (30mm) x 1.00”h (25mm) x 18.00”l (457mm)
Features
• Continuous, flicker-free dimming from 100% to 10%
• Standard 3-wire line-voltage phase-control
technology for consistent fixture-to-fixture dimming
performance
• Models available for T5 and T5-HO linear, T8 linear
and U-bent, and T5 twin-tube lamps
• Programmed rapid start design preheats lamp
cathodes before applying full arc voltage
• Lamps turn on to any dimmed level without flashing
to full brightness
• Low harmonic distortion throughout the entire
dimming range maintains power quality
• Frequency of operation ensures that ballast does
not interfere with infrared devices operating
between 38 and 42 kHz
• Inrush current limiting circuitry eliminates circuit
breaker tripping, switch arcing, and relay failure
• End-of-lamp-life protection circuitry (for T5 and
T5-HO linear models) ensures safe operation
throughout entire lamp life cycle
• For linear lamps, ballasts maintain consistent light
output for different lamp lengths, ensuring uniformity
• Ultra-quiet operation
• Protected from miswires of any input power to
control lead
• 100% compatible with all Lutron 3-wire fluorescent
controls
• 100% performance tested at factory
• Designed and assembled in the USA
• 5-year limited warranty with Lutron field service
commissioning (3-year standard warranty) from
date of purchase
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Eco-10, case type D
1.58”w (40mm) x 1.00”h (25mm) x 9.50”l (241mm)
Eco-10, case type F
2.38”w (60mm) x 1.50”h (38mm) x 9.50”l (241mm)
Page
FC1,FC2,FP1,FP2,FP4,WW1,FS1
Eco-10TM
Fluorescent Dimming Ballasts
10%
Lighting Management Dimming
Eco-10 (3) 07.06.04
Eco-10 Ballast Models
120 VOLTS
Lamp
Type
T5 linear
5/8” diameter
T5-HO linear
high output
Lamp
Watts
(length)
Lamps Case Ballast
per
Type Current
ballast
(amps)
Eco-10
Model Number
Ballast
Current
(amps)
Eco-10
Model Number
14W
(22”)
1
2
C
C
.17
.32
E 3 T514 C 120 1
E 3 T514 C 120 2
.08
.14
E 3 T514 C 277 1
E 3 T514 C 277 2
21W
(34”)
1
2
C
C
.25
.43
E 3 T521 C 120 1
E 3 T521 C 120 2
.11
.19
E 3 T521 C 277 1
E 3 T521 C 277 2
28W
(45.3”)
1
2
C
C
.30
.55
ECO-T528-120-1
ECO-T528-120-2
.14
.25
ECO-T528-277-1
ECO-T528-277-2
24W
(21.5”)
1
2
C
C
.26
.45
ECO-T524-120-1
ECO-T524-120-2
.13
.20
ECO-T524-277-1
ECO-T524-277-2
39W
(33.4”)
1
2
C
C
.38
.76
ECO-T5H39-120-1
ECO-T5H39-120-2
.17
.31
ECO-T5H39-277-1
ECO-T5H39-277-2
54W
(45.3”)
1
2
C
C
.58
1.1
ECO-T554-120-1
ECO-T554-120-2
.25
.45
ECO-T554-277-1
ECO-T554-277-2
36/39W
(16”)
1
2
3
F
F
F
.33
.58
.85
ECO-T539-120-1
ECO-T539-120-2
ECO-T539-120-3
.14
.25
.35
ECO-T539-277-1
ECO-T539-277-2
ECO-T539-277-3
40W
(22”)
1
2
3
F
F
F
.33
.61
.88
ECO-T540-120-1
ECO-T540-120-2
ECO-T540-120-3
.14
.25
.38
ECO-T540-277-1
ECO-T540-277-2
ECO-T540-277-3
50W
(22”)
1
2
F
F
.38
.69
ECO-T550-120-1
ECO-T550-120-2
.17
.32
ECO-T550-277-1
ECO-T550-277-2
5/8” diameter
T5 Twin-Tube
5/8” diameter
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
277 VOLTS
Model Numbers:
Page
FD1,FD2,FD3,FD4,FD5,FC3,WW3,FP3
Compact SETM 5%
Ballast
High-Performance Dimming
CompactSE-1 03.08.04
Compact SE Overview
For designs requiring the energy savings and
aesthetic appeal of dimmed T4 compact fluorescent
or T5 twin-tube lamps, Compact SE dimming
ballasts are your solution. The Compact SE product
family includes ballasts for nearly every type of
dimmable compact fluorescent lamp.
Compact SE, case type A
3.00”w (76mm) x 1.00”h (25mm) x 4.90”l (124mm)
Features
• Continuous, flicker-free dimming from 100% to 5%
• Standard 3-wire line-voltage phase-control
technology for consistent fixture-to-fixture
dimming performance
• Models for 4-pin T4 compact lamps and T5
twin-tube lamps
• Programmed rapid start design will preheat lamp
cathodes before applying full arc voltage
• Lamps turn on to any dimmed level without
flashing to full brightness
• Low harmonic distortion throughout the entire
dimming range maintains power quality
• Frequency of operation ensures that ballast does
not interfere with infrared devices operating
between 38 and 42 kHz
• Inrush current limiting circuitry eliminate circuit
breaker tripping, switch arcing, and relay failure
• End-of-lamp-life protection circuitry ensures safe
operation throughout entire lamp life cycle
• Ultra quiet operation
• Protected from miswires of any input power to
control lead, or lamp leads to each other or ground
• 100% compatible with all Lutron 3-wire
fluorescent controls
• 100% performance tested at factory
• Designed and assembled in the USA
• 5-year limited warranty with Lutron field service
commissioning (3-year standard warranty) from
date of purchase
• Ballasts that dim T4 compact fluorescent lamps
are intended for factory installation by OEM
fixture manufacturer.
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Compact SE, case type B
3.00”w (76mm) x 1.00”h (25mm) x 6.75”l (171mm)
Compact SE, case type F
2.38”w (60mm) x 1.50”h (38mm) x 9.50”l (241mm)
Page
FD1,FD2,FD3,FD4,FD5,FC3,WW3,FP3
Compact SETM 5%
Ballast
High-Performance Dimming
CompactSE-3 03.08.04
Compact SE Ballast Models
120 VOLTS
Lamp
Type
T4 4-Pin
Quad-Tube
Lamp
Watts
Lamps Case Ballast
Type Current
per
(amps)
ballast
Compact SE
Model Number 1
Ballast
Current
(amps)
Compact SE
Model Number 1
18W
1
2
A
B
.20
.42
FDB-T418-120-1-S
FDB-T418-120-2-S
.08
.17
FDB-T418-277-1-S
FDB-T418-277-2-S
26W
1
2
A
B
.26
.50
FDB-T426-120-1-S
FDB-T426-120-2-S
.12
.21
FDB-T426-277-1-S
FDB-T426-277-2-S
18W
1
2
A
B
.20
.42
FDB-T418-120-1-S
FDB-T418-120-2-S
.08
.17
FDB-T418-277-1-S
FDB-T418-277-2-S
26W
1
2
A
B
.26
.50
FDB-T426-120-1-S
FDB-T426-120-2-S
.12
.21
FDB-T426-277-1-S
FDB-T426-277-2-S
32W
1
2
A
B
.31
.59
FDB-T432-120-1-S
FDB-T432-120-2-S
.13
.24
FDB-T432-277-1-S
FDB-T432-277-2-S
42W
1
2
B
B
.36
.67
FDB-T442-120-1-S
FDB-T442-120-2-S
.16
.29
FDB-T442-277-1-S
FDB-T442-277-2-S
36/39W
(16”)
1
2
3
F
F
F
.33
.58
.85
FDB-1643-120-1
FDB-1643-120-2
FDB-1643-120-3
.14
.25
.35
FDB-1643-277-1
FDB-1643-277-2
FDB-1643-277-3
40W
(22”)
1
2
3
F
F
F
.33
.61
.88
FDB-2227-120-1
FDB-2227-120-2
FDB-2227-120-3
.14
.25
.38
FDB-2227-277-1
FDB-2227-277-2
FDB-2227-277-3
50W
(22”)
1
2
F
F
.38
.69
FDB-2243-120-1
FDB-2243-120-2
.17
.32
FDB-2243-277-1
FDB-2243-277-2
1/2” diameter
T4 4-Pin
Triple-Tube
277 VOLTS
1/2” diameter
T5 Twin-Tube
5/8” diameter
1
Mounting studs standard for T4 ballasts. Delete suffix -S in the model number if mounting studs not needed.
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Page
SC1
[email protected]
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
Num.
of
Lamp
s
* F24T5/HO
1
F24T5/HO
2
F39T5/HO
1
FC12T5
1
FC9T5
1
FC9T5
2
FT24W/2G11
1
FT24W/2G11
2
FT36W/2G11
1
FT40W/2G11/RS
1
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
0
0
39
40
22
22
24
24
36
40
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0.23
0.44
0.34
0.34
0.23
0.44
0.23
0.44
0.29
0.40
Wiring Diagram
Input
Power
(ANSI
Watts)
27
52
40
40
27
52
27
52
34
47
CENTIUM T5
Electronic
Programmed Start
Series
120
50/60 HZ
Active
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
1.02
1.00
0.90
0.84
1.02
1.00
1.02
1.00
0.90
1.00
10
10
10
10
10
10
10
10
10
10
0.98
0.98
0.98
0.98
0.98
0.98
0.98
0.98
0.98
0.98
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
3.78
1.92
2.25
2.10
3.78
1.92
3.78
1.92
2.65
2.13
Enclosure
For 1 lamp operation, do not use yellow leads
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Enclosure Dimensions
Standard Lead Length (inches)
Black
White
Blue
Red
Yellow
Gray
Violet
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
Yellow/Blue
Blue/White
Brown
Orange
Orange/Black
Black/White
Red/White
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
OverAll (L)
16.70 "
16 7/10
42.4 cm
Width (W)
1.18 "
1 9/50
3 cm
Height (H) Mounting (M)
1.00 "
16.34 "
1
16 17/50
2.5 cm
41.5 cm
Revised 09/01/2004
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
SC4
Metal
Halide
Lamp Ballast
Catalog Number 71A6092LL
For 400W M135/M155
60 Hz CWA
Status: Active
DIMENSIONS AND DATA
4 1/4 X 4 3/4 CORE - 2 COIL UNIT
6.50"
5.75"
0.7"
1.30"
A
B
MAX.
0.30" WIDE
2 SLOTS
4 HOLES
CLEARED
FOR #10
THRU-BOLTS
4.75"
4.40"
3.90"
4.25"
Capacitor: 7C260P33-R
4.40"
INPUT VOLTS
120 208 240 277
CWA
CIRCUIT TYPE
96%
POWER FACTOR (min)
REGULATION
Line Volts
±10%
Lamp Watts
±10%
LINE CURRENT (Amps)
Operating...................................................
3.80 2.20 1.90 1.65
Open Circuit...............................................
2.10 1.20 1.07 0.92
Starting......................................................
3.16 1.78 1.58 1.38
UL TEMPERATURE RATINGS
Insulation Class
H(180°C)
Coil Temperature Code
A
A
A
A
1029
MIN. AMBIENT STARTING TEMP.
-40°F or -40°C
NOM. OPEN CIRCUIT VOLTAGE
265
INPUT VOLTAGE AT LAMP DROPOUT...........................
64 114 123 152
INPUT WATTS
434
RECOMMENDED FUSE (Amps).....................................
10
6
5
5
CORE and COIL
Dimension (A)
2.28
Dimension (B)
4.00
Weight (lbs.)
14.5
Lead Lengths
18"
CAPACITOR REQUIREMENT
Microfarads
26.0
Volts (min.)
330
Fault Current Withstand (amps)
60 Hz TEST PROCEDURES (Refer to Advance Test
Procedure for HID Ballasts - Form 1270)
High Potential Test (Volts)
1 minute
2000
2 seconds
2500
Open Circuit Voltage Test (Volts)
250-300
Short-Circuit Current Test (Amps)
Secondary Current
3.60-4.40
Input Current..............................................
2.52 1.44 1.26
3.78 2.16 1.89
1.08
1.63
-
Wiring Diagram:
LINE V
LAMP
LINE V
Capacitance:
Dia/Oval Dim:
Height:
Temp Rating:
LINE V
X3
X1
IGNITOR
LINE V
X2
CAP
26
1.75
5.15
105°C
CAP
LAMP
CAP
COM
COM
Fig. M
Ordering Information
Ignitor: LI533-H4
Order Suffix
500D.
Description
Ballast With Ignitor and Dry Film Capacitor
Ballast to Lamp Distance
(BTL) = 2 feet
Temp Rating: 105°C
Data is based upon tests performed by Advance Transformer in a controlled environment and representitive of relative performance.
Actual performance can vary depending on operating conditions. Specifications are subject to change without notice.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
04/06/04
SC3,SC5,GR1
Metal
Halide
Lamp Ballast
Catalog Number 71A5237BP
For 70W
M98/M143
60 Hz R-HPF
Status: Active
DIMENSIONS AND DATA
2 5/8 X 2 3/16 CORE
4.00"
3.50"
0.75"
A
B
MAX.
0.30" WIDE
2 SLOTS
2.65"
2.20"
.20"
2.20"
4 HOLES
CLEARED
FOR #6
THRU-BOLTS
1.75"
.062"
.20"
Capacitor: 7C080L33-R
INPUT VOLTS
277
R-HPF
CIRCUIT TYPE
90%
POWER FACTOR (min)
REGULATION
Line Volts
±5%
Lamp Watts
±10%
LINE CURRENT (Amps)
Operating...................................................
0.32
Open Circuit...............................................
0.80
Starting......................................................
0.50
UL TEMPERATURE RATINGS
Insulation Class
H(180°C)
Coil Temperature Code
A
1029
MIN. AMBIENT STARTING TEMP.
-20°F or -30°C
NOM. OPEN CIRCUIT VOLTAGE
277
INPUT VOLTAGE AT LAMP DROPOUT...........................
190
INPUT WATTS
85
RECOMMENDED FUSE (Amps).....................................
2
CORE and COIL
Dimension (A)
1.50
Dimension (B)
2.90
Weight (lbs.)
2.9
Lead Lengths
12"
CAPACITOR REQUIREMENT
Microfarads
8.0
Volts (min.)
280
Fault Current Withstand (amps)
60 Hz TEST PROCEDURES (Refer to Advance Test
Procedure for HID Ballasts - Form 1270)
High Potential Test (Volts)
1 minute
2000
2 seconds
2500
Open Circuit Voltage Test (Volts)
260-290
Short-Circuit Current Test (Amps)
Secondary Current
0.85-1.25
Input Current..............................................
0.20
0.45
-
-
-
-
Wiring Diagram:
INTEGRATED
IGNITOR BALLAST
LINE V
CAP
Capacitance:
Dia/Oval Dim:
Height:
Temp Rating:
LAMP
IGNITOR
LAMP
COM
8
1.25
2.9
105°C
Fig. H
Ordering Information
Ignitor: INTEGRAL
Order Suffix
An ignitor integral to the
core and coil assembly is
used to start the lamp.
500DB
510DB
600B
610B
Description
Ballast With Integral Igniter and Dry Film Capacitor
Ballast w/Welded Bracket, Integral Igniter & Dry Film Cap.
Ballast and Integral Igniter, No Capacitor
Ballast w/Welded Bracket and Integral Igniter, No Capacitor
Ballast to Lamp Distance
(BTL) = 2 feet
Temp Rating: 125°C
Data is based upon tests performed by Advance Transformer in a controlled environment and representitive of relative performance.
Actual performance can vary depending on operating conditions. Specifications are subject to change without notice.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
05/15/03
FT1,FT2
REL-3P32-SC
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
F17T8
F25T8
F25T8
* F32T8
F32T8
F32T8/ES (30W)
F40T8
Num.
of
Lamp
s
3
2
3
2
3
2
2
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
17
25
25
32
32
30
40
0/-18
0/-18
0/-18
0/-18
0/-18
60/16
0/-18
0.39
0.42
0.55
0.54
0.71
0.51
0.66
Wiring Diagram
WHITE
BLACK
Input
Power
(ANSI
Watts)
47
54
66
65
85
61
79
STANDARD ELEC
Electronic
Instant Start
Parallel
120
60 HZ
Active
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
0.99
1.06
0.93
1.03
0.88
1.03
1.01
20
20
20
20
20
20
20
0.99
0.99
0.99
0.99
0.99
0.99
0.99
1.7
1.7
1.7
1.7
1.7
1.7
1.7
2.11
1.96
1.41
1.58
1.04
1.69
1.28
Enclosure
BLUE
BALLAST
BLUE
BLUE
RED
LAMP
LINE
LAMP
Diag. 70
Insulate unused blue
lead for 1000V
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Enclosure Dimensions
Standard Lead Length (inches)
Black
White
Blue
Red
Yellow
Gray
Violet
in.
25L
25R
31R
37L
cm.
63.5
63.5
78.7
94
0
0
0
in.
Yellow/Blue
Blue/White
Brown
Orange
Orange/Black
Black/White
Red/White
cm.
0
0
0
0
0
0
0
OverAll (L)
9.50 "
9 1/2
24.1 cm
Width (W)
1.7 "
1 7/10
4.3 cm
Height (H) Mounting (M)
1.18 "
8.90 "
1 9/50
8 9/10
3 cm
22.6 cm
Revised 08/21/2002
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
FT1,FT2
ROP-2P32-SC
Brand Name
Ballast Type
Starting Method
Lamp Connection
Input Voltage
Input Frequency
Status
Electrical Specifications
Lamp Type
F17T8
F25T8
F25T8
* F32T8
F32T8
F32T8/ES (28W)
F32T8/ES (28W)
F32T8/ES (30W)
F32T8/ES (30W)
F40T8
F40T8
Num.
of
Lamp
s
2
1
2
1
2
1
2
1
2
1
2
Rated
Lamp
Watts
Min. Start
Temp
(°F/C)
Input
Current
(Amps)
17
25
25
32
32
28
28
30
30
40
40
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
0/-18
60/16
60/16
32/00
32/00
0.26
0.23
0.37
0.30
0.47
0.25
0.41
0.28
0.44
0.35
0.56
Wiring Diagram
WHITE
BLACK
Input
Power
(ANSI
Watts)
31
27
43
35
55
30
48
33
52
41
67
OPTANIUM
Electronic
Instant Start
Parallel
120
50/60 HZ
Active
Ballast
Factor
MAX
THD
%
Power
Factor
MAX Lamp
Current
Crest Factor
B.E.F.
0.90
1.02
0.88
1.01
0.88
1.02
0.87
1.01
0.88
1.01
0.88
10
15
10
10
10
15
10
10
10
10
10
0.97
0.97
0.99
0.98
0.99
0.95
0.98
0.97
0.99
0.99
0.99
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
2.90
3.78
2.05
2.89
1.60
3.40
1.81
3.06
1.69
2.46
1.31
Enclosure
BLUE
BALLAST
BLUE
RED
LAMP
LINE
Diag. 68
Insulate unused blue
lead for 1000V
The wiring diagram that appears above is
for the lamp type denoted by the asterisk (*)
Enclosure Dimensions
Standard Lead Length (inches)
Black
White
Blue
Red
Yellow
Gray
Violet
in.
25L
25L
31R
37L
0
0
0
cm.
63.5
63.5
78.7
94
0
0
0
Yellow/Blue
Blue/White
Brown
Orange
Orange/Black
Black/White
Red/White
in.
0
0
0
0
0
0
0
cm.
0
0
0
0
0
0
0
OverAll (L)
9.50 "
9 1/2
24.1 cm
Width (W)
1.7 "
1 7/10
4.3 cm
Height (H) Mounting (M)
1.18 "
8.90 "
1 9/50
8 9/10
3 cm
22.6 cm
Revised 07/20/2004
Data is based upon tests performed by Advance Transformer in a controlled environment and representative of relative performance. Actual performance
can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted.
ADVANCE TRANSFORMER CO.
O'HARE INTERNATIONAL CENTER · 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018
Customer Support/Technical Service: Phone: 800-372-3331 · Fax: 630-307-3071
Corporate Offices: Phone: 800-322-2086
CONFERENCE ROOM
®
GRAFIK Eye 3000 Series
Preset Dimming Controls
3000-1 06.11.04
GRAFIK Eye 3000 Series Control Unit
Description
Cover (shown open)
• Provides pushbutton recall of four preset
lighting scenes, plus Off.
• Allows setup of lighting scenes using buttons
on the Control Unit.
• Controls many light source types directly, and
others using power interfaces.
• Provides lockout options to prevent
accidental changes.
• Includes built-in infrared receiver for
operation with an optional remote control.
Models available to:
• Accept 120V, 220-240V (non-CE), 230V (CE)
and 100V input power.
• Control two to six zones of lighting.
Base
Zone
Infrared Receiver
Scene
Selection
Buttons
GRX-3100 Control Units
Provide setup using buttons on the Control
Unit.
GRX-3500 Control Units
Provide optional setup using a PC, including
setting lighting levels in 1% increments.
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Page 1
CONFERENCE ROOM
GRAFIK Eye 3000 Series
®
Preset Dimming Controls
3000-7 06.11.04
How to Build a Model Number
GRX-3506-T-AU-WH
Prefix
Set-Up
Method
Color
Option
Input
Number
Voltage
of Zones
Cover
Option
Cover Options
Color Options
Opaque
A
Cover and Base will match.
Architectural Matte Finishes
Standard – Ship in 48 hours
Cover Option: A or T
White
WH
Ivory
IV
Beige
BE
Gray
GR
Brown
BR
Black
BL
Translucent Black
T
Black Cover and choice of
base color.
Also available:
- Custom controls
- Color matching
- Engraving
These options ship in 4 to 6
weeks
Prefix:
GRX for Grafik Eye 3000 Series
Control Units
Set-Up Method:
1 for standard via front panel
5 for PC setup
Number of Zones:
2, 3, 4, or 6
Cover Option:
A for Opaque
T for Translucent Black
Input Voltage
__ (no code) for 120V Single Feed
AU for 220-240V (non-CE)
CE for 230V (CE)
JA for 100V
Color Option:
See Color Options list
Designer Gloss Finishes
Ship in 4 to 6 weeks
Cover Option: A only
White
GWH
Light Almond
GLA
Almond
GAL
Ivory
GIV
Satin Color Matte Finishes
Cover Option: A or T
Hot
HT
Ochre
OC
Terracotta
TC
Desert Stone
DS
Stone
ST
Limestone
LS
Blue Mist
BT
Midnight
MN
Taupe
TP
Biscuit
BI
Eggshell
ES
Snow
SW
Architectural Metal Finishes
Cover Option: T only
Bright Brass
BB
Bright Chrome BC
Satin Brass
SB
Satin Chrome SC
Satin Nickel
SN
Antique Brass QB
Antique Bronze QZ
Bright Nickel
BN
Anodized Aluminum Finishes
Cover Option: T only
Clear
CLA
Black
BLA
Brass
BRA
Bronze
BZA
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Page 3
CONFERENCE ROOM
GRAFIK Eye 3000 Series
®
Preset Dimming Controls
3000-9 06.11.04
Model Numbers
120V Input Power
Number
of Zones
Standard Setup
PC Setup
Unit Capacity
(Watts/VA)
Zone Capacity
(Watts/VA)
2
3
4
6
GRX-3102-_-__
GRX-3103-_-__
GRX-3104-_-__
GRX-3106-_-__
GRX-3502-_-__
GRX-3503-_-__
GRX-3504-_-__
GRX-3506-_-__
1200
1500
2000
2000
800
800
800
800
220–240V (non-CE) Input Power
Number
of Zones
Standard Setup
PC Setup
Unit Capacity
(Watts/VA)
Zone Capacity
(Watts/VA)
2
3
4
6
GRX-3102-_-AU-__
GRX-3103-_-AU-__
GRX-3104-_-AU-__
GRX-3106-_-AU-__
GRX-3502-_-AU-__
GRX-3503-_-AU-__
GRX-3504-_-AU-__
GRX-3506-_-AU-__
1600
2400
3000
3000
1200
1200
1200
1200
230V (CE) Input Power
Number
of Zones
Standard Setup
PC Setup
Unit Capacity
(Watts/VA)
Zone Capacity
(Watts/VA)
2
3
4
6
GRX-3102-_-CE-__
GRX-3103-_-CE-__
GRX-3104-_-CE-__
GRX-3106-_-CE-__
GRX-3502-_-CE-__
GRX-3503-_-CE-__
GRX-3504-_-CE-__
GRX-3506-_-CE-__
1600
2300
2300
2300
800
800
800
800
100V Input Power
Number
of Zones
Standard Setup
PC Setup
Unit Capacity
(Watts/VA)
Zone Capacity
(Watts/VA)
2
3
4
6
GRX-3102-_-JA-__
GRX-3103-_-JA-__
GRX-3104-_-JA-__
GRX-3106-_-JA-__
GRX-3502-_-JA-__
GRX-3503-_-JA-__
GRX-3504-_-JA-__
GRX-3506-_-JA-__
1000
1250
1600
1600
600
600
600
600
R
S P E C I F I C AT I O N S U B M I T TA L
Job Name:
Job Number:
Model Numbers:
Page 4
FUNCTION ROOM/LOBBY
PRESET DIMMING CONTROLS
®
GRX-4000 Control Units
rev 4000-1a 7.20.00
GRX-4000 Control Units
Preset Controls
• 4 preset lighting scenes and off for
up to 24 zones, accessible from Control
Unit faceplate.
• 12 additional scenes stored in Control
Unit, accessible via Wallstations and/or
Control Interfaces.
• Light levels fade smoothly between
scenes. Fade time: 0-59 seconds or 1-60
minutes. Can be set differently for each
scene.
Cover (shown open)
Key Design Features
• Meets IEC 801-2. Tested to withstand
15kV electrostatic discharge without
damage or memory loss.
• Provides power failure memory:
Automatically restores lighting to scene
selected prior to power interruption.
• Has faceplate that snaps on with no
visible means of attachment.
Base
Zone
Infrared Receiver
Scene Selection Buttons
DESCRIPTION
S P E C I F I C AT I O N S
• Provide pushbutton recall of four
preset lighting scenes.
• Control virtually any light source.
• Provide lockout options to prevent
accidental changes.
• Include built-in infrared receiver for
operation with an optional remote control.
Operating Voltage
• Low-voltage type Class 2 (PELV),
12VDC to 24VFW.
• Lightning Strike Protection:
Meets ANSI/IEEE standard 62.41-1980.
Can withstand voltage surges of up to
6000V and current surges up to 3000A.
Models available to:
• Control two to 24 zones of lighting.
• Provide easy setup of
preset lighting scenes:
GRX-4100 Control Units provide
standard setup via pushbuttons on
the Control Unit.
GRX-4500 Control Units provide
optional setup via a PC, including setting
lighting levels in 1% increments.
Sources/Load Types
Operates sources with a smooth continuous
Square Law dimming curve or on a full
conduction non-dim basis via GP and LP
Dimming Panels and XP SoftswitchTM Panels.
System Communications and Capacities
Low-voltage type Class 2 (PELV) wiring
connects Control Units, Wallstations, and
Control Interfaces:
• You can link up to 8 Control Units to
control up to 64 zones.
• You can add up to 16 total Wallstations
and Control Interfaces for a total of 24
control points.
Environment
• 32-104°F (0-40°C). Relative humidity
less than 90% non-condensing.
GRX-4000 Control Units work with:
• GRAFIK Eye Wallstations
• GP and LP Dimming Panels
• XP SoftswitchTM Panels
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
FUNCTION ROOM/LOBBY
PRESET DIMMING CONTROLS
®
GRX-4000 Control Units
rev 4000-2a 7.20.00
H OW TO B U I L D A M O D E L N U M B E R
Number of Zones
(2,3,4,6,8,16, or 24)
Standard Prefix for
GRAFIK Eye Series 4000
Control Units
Color Option
GRX-4506-T-WH
Set up method
1 for standard
via front panel
5 for PC setup
Cover Options
A for Opaque
T for Translucent
Black
MODELS
NUMBER
OF ZONES
STANDARD SETUP
MODEL NUMBER
PC SETUP
2
3
4
6
8
16
24
GRX-4102-_-__
GRX-4103-_-__
GRX-4104-_-__
GRX-4106-_-__
GRX-4108-_-__
GRX-4116-_-__
GRX-4124-_-__
GRX-4502-_-__
GRX-4503-_-__
GRX-4504-_-__
GRX-4506-_-__
GRX-4508-_-__
GRX-4516-_-__
GRX-4524-_-__
C OV E R O P T I O N S
Opaque
A
Cover and Base will match.
Translucent Black
T
Black cover and your
choice of base color.
BA S E C O L O R S
Matte Finishes
Standard – Ships in 48 hours
White
WH
Ivory
IV
Beige
BE
Gray
GR
Brown
BR
Black
BL
Gloss Finishes
Ships in 4 to 6 weeks
Cover Choice: A only
White
WH
Light Almond
GLA
Almond
GAL
Ivory
GIV
Metal Finishes
Cover Choice: T only
Bright Brass
BB
Bright Chrome
BC
Bright Nickel
BN
Satin Brass
SB
Satin Chrome
SC
Satin Nickel
SN
Antique Brass
QB
Antique Bronze
QZ
Anodized Aluminum
Clear
CLA
Black
BLA
Brass
BRA
Custom Controls, color
matching, and engraving
available, Ships in
4 to 6 weeks
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
FUNCTION ROOM/LOBBY
POWER PANELS
GRAFIK Systems
GP Dimming Panels
rev gp-1a 7.20.00
GP Dimming Panels
GP3/4
Mini Panels
GP8-24
Standard-Size Panels
DESCRIPTION
• Provide power and dimming for up to
144 load circuits.
• Control any light source,
including full-conduction non-dim.
Models available for:
• 100-127V, 220-240V (non CE),
230V (CE), and 277V.
• 3 to 144 circuits.
• Different feed types and breakers.
GP Dimming Panels work with:
• GRX-4000 Control Units
• GRAFIK 5000 and 6000 Systems
• LP Dimming Panels
• XP SoftswitchTM Panels
• DMX512 dimming systems via the
2LINKTM option.
GP36
Large-Size Panels
GP48-144
Large-Size Panels
Get a Panel Fast!
LISA (Lutron Integrated System Advantage)
Program ships standard Panels 3 to 5 working
days from receipt of approved drawings.
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
TYPICAL PRESET WALLSTATION
WALLSTATIONS
®
seeTouch
NEW… seeTouch Wallstations
TM
For GRAFIK Systems and HomeWorks Interactive Systems
Big, backlit buttons
Easy to find and press – even in a darkened AV presentation
room. Buttons select preset lighting scenes or turn lights off.
Engraving on buttons
Easy to use – the labels show what each button does.
Easy to specify, too – simply order labeled buttons.
Optional Built-in infrared receiver
Occupants can use a handheld Wireless Remote Control to
• Change scenes
• Temporarily adjust light levels
• Turn lights off
Optional Raise/Lower buttons
For fine-tuning lighting
Colors/Finishes
Faceplate and matching buttons are available in a variety of
plastic colors. Metal finishes are also available.
Field Configurable Buttons
Just swap buttons and faceplates to change control
MODEL NO. SGRX-4S-NL-BL
Consult Lutron for exact model numbers and detailed mounting and
wiring information. 1-800-523-9466 www.lutron.com/seetouch
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
Page 1
MODEL NUMBERS:
POOL
system operation
radiotouch
™
Fluorescent Fixtures
(With Lutron
dimming ballasts)
Power
Power
Power and
RadioTouch
Control
Controller
RadioTouch™
Controller
Fluorescent
Fixtures
(With
Lutron
dimming
ballasts)
Power
RadioTouch
Wallbox
Transmitter
RadioTouch Tabletop
Transmitter(s)
By simply pressing buttons on a RadioTouch transmitter, radio frequency
signals are sent to RadioTouch Controllers housed in the ceiling. These
Controllers then send signals to Lutron dimming ballasts adjusting the
light levels and also send signals to optional motorized window treatments
and projection screens to adjust window treatments or screen levels.
Add up to 16 transmitters in the room to meet your flexibility needs.
1
1
2
2
ON
3
4
5
OFF
1 RadioTouch tabletop
or security mounted
transmitters can
be placed anywhere
in a room.
2 RadioTouch wallbox
transmitters can
replace any wall
switch.
3 One Controller
4
is required per
lighting zone.
The same
Controllers are
used to control
motorized window
treatments and
projection screens.
Equip fluorescent
lighting fixtures
with Lutron
1% Hi-lume®
dimming ballasts.
Call toll-free 1-800-523-9466
5 Lutron dimming
ballasts can be
installed in existing
fixtures or can be
ordered pre-installed
in a Lutron fixture.
2
POOL
controllers
Controllers for lights, window treatments and projection screens
Switches one lighting zone,
plus occupant sensing
(requires sensor); can be
fixture or junction box
mounted
RTA-RX-SW1
• One required per lighting zone
• Accepts inputs from occupant sensors
• Operates at 120/277V
• Switches 16 Amps of high inrush lighting load
Regulates one lighting zone,
plus occupant and daylight
sensing (requires sensor);
can be fixture or junction
box mounted
RTA-RX-F1
• One required per lighting zone
• Controls Lutron Hi-lume®, …co-10™, and TVE ballasts directly
• Controls Lutron Tu-Wire® ballasts, incandescent
and magnetic low voltage sources through an
FDI Load Interface.
• Accepts inputs from occupant sensors and a daylight sensor
• Operates at 120/277V
• 16A continuous dimming capacity
Regulates one lighting zone,
RTA-RX-F-SC1
plus occupant and daylight
sensing (requires sensor), and
switch closure outputs; can be
fixture or junction box mounted
• All functions of RTA-RX-F plus the features below
• Controls Sivoia™ Motorized Window Treatments directly
• Provides up to five momentary output switch
closures to GRAFIK …ye® products or equipment
by others.
Includes one RTA-RX-F-SC and
RTA-RX-F-SC-ACM
one WC-4M-GC for control of
AC Motorized Window Treatments
and projection screens
• All functions of RTA-RX-F-SC plus the features below
• Provides group control of up to 4 AC Motorized Window Treatments
• Additional motorized window treatments can be controlled
by adding more WC-4M-GC or WC-1M-GC group controls
1
Available in 347 Volt models
load interfaces
*
*All load interfaces operate at 120 Volts
Load interfaces for control of lights, window treatments and projection screens
Interfaces for incandescent,
magnetic low voltage,
electronic low voltage and
Lutron Tu-Wire ballasts
Interface to AC Motorized
Window Treatments and
projection screen motors
FDI-INC-20002
• Connects RadioTouch™ Controller to an incandescent or
magnetic low voltage lighting circuit; 2000W capacity
FDI-ELV-10002
• Connects RadioTouch Controller to an electronic
low voltage lighting circuit; 1000VA capacity
FDI-FTU-16A-1202
• Connects RadioTouch Controller to one Tu-Wire
ballast fluorescent lighting circuit; 16A capacity
WC-4M-GC
• Provides individual or master control of one or
up to four AC Motorized Window Treatments or
projection screens
• Add to RTA-RX-F-SC-ACM for control of additional
AC Motorized Window Treatments
WC-1M-GC
Call toll-free 1-800-523-9466
2
Backbox mounted (junction box or 2-gang)
10
POOL
wallbox transmitters
*
*All Wallbox transmitters operate at 120/277 Volts
Wallbox transmitters for control of lights
ON
OFF
ON
OFF
On/Off control of one
or more switched
lighting zones
RTA-WX-2BSW-WH1
On/Off and Raise/Lower
control of one or more
dimmable lighting zones
RTA-WX-2B-WH1
• Use in multiples for multi-location dimming
• Can communicate with multiple Controllers
for master control of multiple lighting zones
Four preset levels plus
Off and Raise/Lower control
of one or more dimmable
lighting zones
RTA-WX-5B-WH2
• Use in multiples for multi-location control
• Can communicate with multiple Controllers
for master control of multiple lighting zones
• Use in multiples for multi-location switching
• Can communicate with multiple Controllers
for master control of multiple lighting zones
Wallbox transmitters for control of Sivoia™ Motorized Window Treatments
Open/Close and Raise/Lower
control of one or more Sivoia
Motorized Window Treatment
zones
ON
OFF
RTA-WX-S2LB-WH1
• Use in multiples for multi-location Sivoia Window Treatments
• Can communicate with multiple Controllers for master
control of Sivoia Motorized Window Treatment zones
Three presets plus Open/
RTA-WX-S5SB-WH2
Close and Raise/Lower control
of one or more Sivoia Motorized
Window Treatment zones
• Use in multiples for multi-location Sivoia Window Treatments
• Can communicate with multiple Controllers for master
control of Sivoia Motorized Window Treatment zones
Wallbox transmitters for control of AC Motorized Window Treatments and projection screens
Open/Close/Stop control
of one or more AC Window
Treatment zones
OPEN
STOP
CLOSE
RTA-WX-C3LB-WH1
(large buttons)
RTA-WX-C3SB-WH2
• Use in multiples for multi-location AC Window Treatments
• Can communicate with multiple Controllers for master
control of AC Window Treatment zones
(slim buttons)
Up/Down control for one
or more AC motorized
projection screens
UP
DOWN
RTA-WX-C2LB-WH1
(large buttons)
RTA-WX-C2SB-WH2
(slim buttons)
• Use in multiples for multi-location
AC motorized projection screen control
• Can communicate with multiple Controllers for
master control of multiple projection screen zones
claro wallplates
®
Screwless wallplates for single or multi-gang installations
Single-Gang
Screwless Wallplate
Two-Gang
Screwless Wallplate
Three-Gang
Screwless Wallplate
Four-Gang
Screwless Wallplate
CW-1-WH
CW-2-WH
CW-3-WH
CW-4-WH
• Contact Lutron Customer Service for wallplate laser-engraving at 1.888.LUTRON1
• For 5- and 6-Gang applications, contact Lutron Customer Service
1
Call toll-free 1-800-523-9466
Standard button laser-engraving included on large button transmitters
2
Factory button labels included with slim-button transmitters
11
for use with microWATT®
Lighting Controllers
PhotoSensor
POOL PHOTOCELL
General Description
Specifications
Lutron’s microPS Photosensor provides automatic daylight
control input to dim fluorescent lighting in response to
changing daylight.
The Photosensor works with Lutron’s microWATT® Lighting
Controller, which integrates signals from it and other
sensors, controls or building automation system inputs to
automatically control lighting to the lowest level required.
TM
1. Provide Photosensor from a supplier with more than 25 years experience
manufacturing electronic switches, fluorescent dimming controls, and
electronic dimming ballasts.
2. Manufacturer shall take sole responsibility for the Photosensor,
lighting controller, dimming controls and dimming ballasts.
3. Manufacturer shall provide a toll-free phone number, with
24 hour emergency access, to specifically service technical and
application questions.
4. Manufacturer shall have ISO 9001 quality certification and factory
employed service engineers.
5. The Photosensor shall provide open loop feedback to the lighting
controller.
6. The Photosensor shall provide a Class 2 low voltage signal.
microPS
Photosensor
7. The Photosensor shall be color and spatially corrected and provide a true
representation of changes in perceived lighting levels.
8. The Photosensor shall be partially shielded for accurate detection of
available daylight.
9. The Photosensor shall have a 60° from vertical viewing angle for accurate
daylight averaging.
microWATT
MW-LC
Lutron Electronic
Dimming Ballast
LUTRON
T8, T12, T5
Fluorescent Lamps
14 1516
microWATT
Lighting
Controller
LIGHTING FIXTURE(S)
Dimming control, occupant sensor,
building automation system inputs
10. The Photosensor’s output shall remain stable over time and temperature
from 0° to 40° C.
11. The Photosensor shall provide a linear response from 0 to 500 footcandles.
12. The Photosensor shall work in conjunction with a Lutron microWATT
Lighting Controller, which shall provide remote calibration adjustment.
Photosensor Placement and Sensitivity
For average size areas
NOTCH
2H
Photosensor Available Model
H
(White)
Photosensor Features
• Provides input to automatically dim fluorescent lights when
available daylight is high, and raise fluorescent lights when
available daylight is low
• Easily calibrated for daylight sensitivity
• Compatible with Lutron microWATT Lighting Controllers
and Hi-lume® and Eco-10TM Dimming Ballasts
• Low voltage Class 2 wiring for simplified installation
• Simple ceiling tile mounting with one 2 inch (50mm) hole;
all hardware provided
NOTCH
H
Area viewed
by Photosensor
H = Effective Window Height
Point notch away from window
when Photosensor can not be
placed 2H away from window.
Place Photosensor two times
window height from outside wall,
and so that viewing area does not
extend out of a window. Point
notch as indicated.
Do not position Photosensor in
the well of a skylight or above
indirect lighting fixtures.
INTERIOR LIGHT LEVEL
MW-PS-WH
For narrow areas
(e.g. corridors, private
offices)
ENERGY
SAVINGS
12 AM
6 AM
12 PM
6 PM
12 AM
TIME OF DAY
TARGET
LIGHT LEVEL
FLUORESCENT
LIGHTING
DAYLIGHT
ENERGY
SAVINGS
SKYWAY PHOTOCELL
D
a
y
l
i
g
h
t
i
n
g
C
o
n
t
r
o
l
s
LS-301 Dimming Photosensor
Automatic dimming based
on ambient light levels
All setup performed remotely
with handheld
Controls standard 0-10 VDC
electronic dimming ballasts
Optional occupant adjustment
via handheld remote
Single zone control
Closed loop daylighting control
PROJECT
LOCATION/TYPE
Product
Overview
Description
Adjustment via Handheld Remote Control
The LightSaver LS-301 is a ceiling mount, low
voltage indoor photosensor that works with standard, 0-10 VDC electronic dimming ballasts to dim
lighting as daylight increases.
All LS-301 adjustments are made with one of two
handheld remotes. The LSR-301-S provides five
buttons for initial set-up, which is easily completed
by first raising or lowering electric light levels to
desired levels, then programming this target level
into the photosensor. The LSR-301-P provides
three buttons for occupants to adjust light levels.
With this optional tool, users can increase target
light levels by up to 25% or reduce them to the
lamp/ballast minimum level. Pressing the “Auto”
button returns the control to programmed levels.
Operation
The LS-301 mounts on a ceiling and utilizes a
spectral filtering system to measure daylight and
electric light levels. A closed loop daylighting
system, the LS-301 measures the total light level
from daylight and electric light in the controlled
area to adjust electric lighting levels. As the daylight contribution increases, the lights dim down.
The photosensor utilizes sliding setpoint control,
which responds to the different spatial distribution
qualities of electric light and daylight. The LS-301
calculates the required light level for current daylight contribution based on two setpoints. One
represents the target level when no daylight is
present (night setpoint) and the other when significant daylight is present (day setpoint).
Features
The LS-301 is designed to blend into its surroundings when installed in any environment. It provides
one zone of daylighting control in a private office or
classroom. In these applications, the LS-301 can
be combined with an occupancy sensor. Often, it is
possible for the LS-301 to share a single power
pack with occupancy sensor(s).
• Provides precise control of lighting to maintain
desired light level
• Separate handheld remote controls for setup
and occupant adjustment to prevent tampering
• Extremely linear photocell response with
greater than 1% accuracy
• Boosts energy savings by reducing maximum
lamp output, often resulting in a 20% reduction
or more compared with lights at full output
• Designed to measure light as the human eye
perceives it, eliminating “overreporting”
illumination levels provided by daylight
www.wattstopper.com
800.879.8585
Applications
• Achieves lumen maintenance by holding target
light level as lamp output decreases over time
SKYWAY PHOTOCELL
D
a
y
l
i
g
h
t
i
n
g
C
o
n
t
r
o
l
s
LS-301 Technical Information
Specifications
Product
Controls
•
•
•
•
•
•
Full range dimming: .2 VDC (minimum) to 10 VDC (100% lighting) output voltage
Current consumption: 30 mA @ 24 VDC
In typical applications, setpoints are adjustable from 20-60 footcandles (210-640 lux)
Controls up to 50 standard dimming ballasts in one zone
Sensor leads: gray and violet to ballast, red and black to 24 VDC
Dimensions: 2.35” diam. x 0.875” depth (60mm x 22mm), threaded piece extends 1.25” (31.8mm)
from back, fits .5” knockout
• 5 year warranty
Remote Controls
Spectral Response Curve
Nighttime setpoint
Button
activation LED
Auto button for
automatic
dimming
Raise/lower
light levels
Daytime setpoint
LSR-301-S
LSR-301-P
Remote handheld (above left) enables easy set-up while
optional occupant remote provides adjustability for
individual lighting preferences.
Wiring &
Installation
The spectral response of the LS-301 photocell closely
matches the sensitivity of the human eye.
Wiring
Mounting and Installation
Placement Guidelines
Coverage
• Mount photocell between 6 and
12 feet (1.8m - 3.7m) from
window.
• Do not mount directly above
direct/indirect pendant fixtures.
Mount at least 4 feet (1.2m)
from pendant fixtures.
Ordering
Information
Watt Stopper/Legrand®
Pub. No. 17503
Catalog No.
Description
LS-301
Dimming Photosensor
LSR-301-S
Setup Remote Control (2 AAA batteries included)
LSR-301-P
Occupant Remote Control (2 AAA batteries included)
Output Voltage
.2 VDC (min.) to 10 VDC (max.)
O
c
c
u
p
a
n
c
y
S
e
n
s
o
r
s
WT Ultrasonic Occupancy Sensor
Ultrasonic technology
with 32 KHz frequency
User-adjustable DIP
switch time delay and
sensitivity settings
Utilizes advanced,
omni-directional,
Doppler technology
600, 1100, 2200 sq ft
and hallway coverages
available
Advanced Signal
Processing automatically
adjusts detection threshold
Product
Overview
Isolated relay allows sensor
to interface with building
control systems
Description
Advanced Signal Processing
The Watt Stopper WT sensors are advanced ultrasonic occupancy sensors with a 32 KHz frequency.
The sensors are available in several models to
control lighting in a wide variety of applications.
The sensors use The Watt Stopper’s Advanced
Signal Processing (ASP). ASP filters out moving air
noise by checking for small cyclical changes found
in turbulent air. This helps to eliminate false ON
problems found in sensors without ASP.
Operation
Applications
The 24 VDC ultrasonic sensors utilize advanced,
omni-directional, Doppler technology. When an
ultrasonic sensor detects movement in a controlled
area, it switches lighting on through a Watt Stopper
power or auxiliary pack. The sensor controls the
power pack through low voltage wiring. Once the
area is vacated and the time delay has elapsed, lighting systems automatically switch off.
Features
WT sensors offer excellent control of lighting for
many areas of a building. The sensors are designed
to effectively control offices, restrooms, storage
areas, and open office areas and can control large
partitioned office spaces when configured in zone
patterns. The WT can be used with Watt Stopper
AS-100 Automatic Control Switches to achieve
manual-on/auto-off function when auto-on is not
desired. The WT sensors’ superior performance and
ease of installation will provide fast paybacks and
many years of energy savings.
• Advanced Signal Processing Circuitry helps to
eliminate false ONs
• Coverage ranges from 600 to 2200 square feet
and 90 linear feet (for hallways)
• Utilizes advanced, omni-directional, Doppler
technology for reliable occupancy detection
• Isolated relay can interface with HVAC, EMS, or
with an additional lighting load
• Angled transmitter and receiver pairs help
optimize sensitivity while eliminating unwanted
detection from ceiling air movement
• DIP switch adjustable time delay and sensitivity
• LED indicates occupancy detection
O
c
c
u
p
a
n
c
y
S
e
n
s
o
r
s
WT Technical Information
Solid state, crystal-controlled (32.768 kHz ± 0.002%)
Omni-directional transmission (360° coverage)
Temperature and humidity resistant 32 kHz receivers
Digital DIP switch time delay (15 seconds to 30 minutes)
Isolated relay with N/O and N/C outputs; rated for 1 Amp @ 30 VDC/VAC
Units per power pack: WT-605: up to 4 (B), up to 5 (BZ). WT-600: up to 3 (B), up to 4 (BZ). WT-1105,
WT-2205, WT-2255: up to 3 (B), up to 5 (BZ). WT-1100, WT-2200, WT-2250: up to 2 (B), up to 3 (BZ).
• Dimensions: 4.8" diameter x 1.5" (122mm x 38mm)
• UL and CUL listed; Five year warranty
Wiring & Controls
Installation
White (Neutral)
Red (Line)
N
White
Hot
Black
Blue
Power Pack
Red
Wiring,
Installation &
Placement
•
•
•
•
•
•
Black
Specifications
Switch
Red (Load)
Transducers
Lighting
Load
DIP switch
Cable
Isolated Relay Outputs
Closure upon Occupancy W i r e s
Normally Closed Contact 1 B r n
2 Red
Common
Normally Open Contact 3 O r n
LED
ON
Attached to a vibration-free surface. Mount the sensors
with the receivers facing the area of coverage. Note: Place
4’ away from supply ducts, 6’ from horizontal discharge
ducts, and 6” from power packs.
1 2 3 4 5 6
Control Output 24VDC
4 Yel
Control Return
5 Grn
No Connection
+24VDC
Common
6 Blu
Sensitivity
S
7 Vio
8 Gra
Enclosed Office Placement
Coverage &
Settings
Fixtures
Fixtures
10' x 10' room
10' x 10' room
Correct
Incorrect
Open Office Placement
For enclosed
spaces, place
sensors as in Figure
A. Sensors placed
as in Figure B may
see out the door
and cause false triggers.
For open office spaces, the
WT-2200 is typically used
because of its 360° coverage
and capability to bounce
ultrasound off of partitions,
walls, floors and other reflectTime Delay
ing objects. A typical layout
place the sensors so they
control the area in zones that
overlap.
42'
DIP Switch Settings
Coverage
45'
52'
26' 22'
0'
22' 26'
45'
= factory preset
=ON – =OFF
21'
WT-2200/2205
14'
WT-1100/1105
DIP Switch #
Time Delay 1 2 3 4 5 6
WT-600/605
5'
WT-2250/2255
0'
5'
14'
15 seconds
2 minutes
4 minutes
6 minutes
8 minutes
10 minutes
12 minutes
14 minutes
16 minutes
18 minutes
20 minutes
22 minutes
24 minutes
26 minutes
28 minutes
30 minutes
Output Disable
Override
21'
Coverages shown represent half-step walking motion. Actual
coverages can vary for each application depending on the
shape and use of space and the obstacles present.
Ordering
Information
The Watt Stopper®, Inc.
Pub. No. 6403
Catalog No. Description
Voltage
Current
Coverage
WT-605
Ultrasonic ceiling sensor
24 VDC
27 mA
600 sq ft; 360°
WT-600
Ultrasonic ceiling sensor w/ isolated relay
24 VDC
37 mA
600 sq ft; 360°
WT-1105
Ultrasonic ceiling sensor
24 VDC
30 mA
1100 sq ft; 360°
WT-1100
Ultrasonic ceiling sensor w/ isolated relay
24 VDC
40 mA
1100 sq ft; 360°
WT-2205
Ultrasonic ceiling sensor
24 VDC
30 mA
2200 sq ft; 360°
WT-2200
Ultrasonic ceiling sensor w/ isolated relay
24 VDC
40 mA
2200 sq ft; 360°
WT-2255
Ultrasonic hallway sensor
24 VDC
30 mA
90 linear ft; 360°
WT-2250
Ultrasonic hallway sensor w/ isolated relay
24 VDC
40 mA
90 linear ft; 360°
All units are white and use Watt Stopper power packs. Current consumption can be slightly higher when only one sensor
per power pack is used.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement