42PD7800TA User manual
ENGLISH
USER'S MANUAL
Thank you very much for purchasing the HITACHI Plasma Display.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to
operate the monitor properly. Keep this manual in a safe place. You
will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
1
Important
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 4 to 7. Mis-use may cause damage to your
plasma monitor, which could shorten its lifespan, or cause injury to
yourself. Should you encounter any difficulty in the set-up or
operation of your monitor, firstly refer to the Troubleshooting guide at
the rear of this manual.
In the unlikely event of a problem occurring with your plasma
monitor, switch off at the mains sockets, pull out the plugs, and
contact your dealer immediately.
CAUTION
Under no circumstances remove the rear cover of your plasma
monitor.
Never guess or take any chances with electrical equipment of any
kind - it is better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, save to
the extent permitted by law.
Plasma Monitor
After the plasma monitor has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is
normal.
Sometimes the screen might have some tiny bright or dark spots.
Please note that this is normal.
CAUTION
To prevent scratches or damages to the plasma screen, do not
knock or rub the surface with sharp or hard objects. Clean the
screen with a soft cloth moistened with warm water and dry with a
soft cloth. A mild soap may be used if the screen is extremely dirty.
Do not use harsh or abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and control panel of the
monitor. When excessively soiled dilute a neutral detergent in water,
wet and wring out the soft cloth and afterward wipe with a dry soft
cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or
cracks.
FEATURES
Large-screen, high-definition plasma display
panel
The 42-inch color plasma display panel, with a resolution of 1024 (H)
x 1024(V) pixels, the 37-inch color plasma display panel with a
resolution of 1024(H) x 1024(V) pixels, and the 32-inch color plasma
display panel with a resolution of 852(H) X 1024(V) pixels, creates a
high-definition, large-screen (aspect ratio : 16:9) and low-profile flat
display. Free from electromagnetic interferences from geomagnetic
sources and ambient power lines, the panel produces high-quality
display images free from color misconvergence and display
distortion.
High Performance Digital Processor
A wide range of input signals can be handed, including composite,
component, and HDMI.
High Definition Digital Processor creates the fine-textured image with
dynamic contrast.
In addition, it corresponds to a broad array of personal computer
signals, from 640 x 400 and 640 x 480 VGA to 1600 x 1200 UXGA.
(Analog Input)
Easy-to-use remote control and on screen
display system
The remote control included eases the work of setting display
controls. Further, the on-screen display system, displays the status of
signal reception and display control settings in an easy-to-view
fashion.
Power saving system
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its
power consumption while it is idle.
Connecting to an Audio Visual Device
• Two composite/S terminals*1, three composite terminals*2, two
component terminals*2, a HDMI terminal and a photo input terminal
(37/42 only) have been added. A composite video output terminal
is also provided as a monitoring output.
*1
A composite/S terminal = A side input
*2
Two composite terminal and two component terminal are used
at the same time. The component terminal would govern.
• A wide range of devices other than personal computers can also
be connected.
• A RGB input is possible to switch to component signals from the
Menu screen.
Power Swivel Feature (TV model only)
It allows to turn the plasma display left or right within ± 30 degree
using the remote control.
Options (AV monitor model only)
Plasma monitor speaker
2
CONTENTS
Main Unit ............................................................................9
Remote control ..................................................................10
Loading Batteries ............................................................10
Handling the Remote Control..........................................10
INSTALLATION INSTRUCTIONS ................13
Installation..........................................................................13
Anti-tumble measures........................................................13
Connecting to an Audio Visual Device..............................14
Connecting to a PC ..........................................................16
Mounting the Speaker Unit................................................17
Mounting the Side Input ..................................................19
Power Cord Connection ....................................................20
OTHER FUNCTIONS ..................................46
Automatic Store ................................................................46
Audio Switching ................................................................47
Power Save Mode ............................................................48
DVD Player/STB Selection ................................................48
Signal Check (RGB mode) ................................................49
ENGLISH
FEATURES ..............................................................2
SAFETY INSTRUCTIONS ..............................4
IMAGE RETENTION OF PLASMA DISPLAY ..8
COMPONENT NAMES ..................................9
TROUBLESHOOTING ..................................50
Symptoms That Seemingly Appear to be Failures............50
Actions to Correct Abnormal Displays ..............................52
PRODUCT SPECIFICATIONS ......................53
Signal Input ......................................................................54
Recommended Signal List ................................................55
OPERATING INSTRUCTIONS......................21
Turning Power On and Off ................................................21
Input Switching ..................................................................22
Size Switching ..................................................................22
Volume Adjustment............................................................24
Audio Mute ........................................................................24
Power Swivel ....................................................................25
Input Signal Screen Display ..............................................26
Displaying MULTI PICTURE ..............................................27
Picture Freezing ................................................................29
Photo Input Display (37/42 only) ......................................30
Using the Menu Screen (On-screen display system) ......33
SETUP MENU (TV mode) ..................................................34
SETUP MENU (Video mode) ............................................36
SETUP MENU (RGB mode: RGB1 (DVI-PC),
RGB2 (RGB)) ..................................................................37
FUNCTION MENU ............................................................39
PICTURE MENU (TV/Video mode) ....................................40
PICTURE MENU (RGB mode) ..........................................43
AUDIO MENU ....................................................................44
TIMER MENU ....................................................................45
LANGUAGE MENU ..........................................................45
Notes about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have
any comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the
product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
3
SAFETY INSTRUCTIONS
This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must
be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and
others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions
thoroughly and fully understand the contents.
WARNING
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to
incorrect handling.
CAUTION
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due
to incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables,
penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure Disconnect the
plug from the
that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be
power outlet.
dangerous.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children
are present.
If liquids or foreign objects should enter the monitor, immediately turn off the power switch, disconnect the power plug from the
power outlet and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage
and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the plasma screen side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on
the monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
4
Do not
disassemble.
SAFETY INSTRUCTIONS (continued)
ENGLISH
About the Symbols (continued)
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the
power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead,
obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value,
type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Surely connect
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed the ground wire.
power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat,
pressure or tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them
because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand
holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where
they exit from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or
clothes, rinse well with water.
• Obey the local laws on disposing the battery.
5
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Be careful in operating power swivel.
Disconnect the
plug from the
power outlet.
Placing hands or faces near the monitor while operating the swivel function could cause a physical injury or damage.
Use special caution in households where children are present.
PRECAUTIONS
• Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
• How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
• Note on image retention
The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination,
the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Tips to prevent such image retention are:
- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,
for long.
- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen
saver function.
- Turn down the contrast and brightness controls.
• How to clean the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen
with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use
harsh or abrasive cleaners.
• How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
6
SAFETY INSTRUCTIONS (continued)
ENGLISH
About the Symbols (continued)
• Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
• Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing
connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
• Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
• Precautions for the installation
- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved
stand or legs with the fixings provided according to the instructions.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the
front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
• Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has
a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm
or handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
7
IMAGE RETENTION OF PLASMA DISPLAY
There are different characteristics that result in panel image retention depending on how the plasma display is used.
Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display
The image retention phenomenon of a plasma panel occurs due to partial phosphor degradation arising from partial character and figure
display.
For example, when the character image as shown in Fig. A at the right is
continuously displayed for a long period of time, the only part of the phosphor
(Red,Green, Blue) that will degrade will be the color of the applicable character
display portion. Consequently, when a white image is displayed on the entire
screen as shown in Fig. a, the character marks displayed up to that time will
become a color difference visible to the eye, but the phosphor will never burn.
[Fig. A]
[Fig. a]
■ The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
• The tendency of the phosphor is to degrade more the brighter the characters
and figures are displayed. When images of figures with different levels of
brightness, as shown in Fig. B, are continuously displayed for a long period
of time, it becomes easier for image marks at locations when the brighter
figures are displayed to be noticeable.
[Fig. B]
[Fig. b]
* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention
is seen differs depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display as much as possible.
A function is provided in the display that controls the brightness of the screen to reduce degradation of the panel. Using this function makes it
possible to reduce image retention.
(Refer to Panel Life (Extend 1.or Extend 2) shown on 39 )
• Set the plasma monitor to an “Screen Wipe” or “Luminance Manager” display.
The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be
reduced by displaying a completely white screen for about 1 ~ 2 hours after terminating the display. Luminance Manager function works to
reduce image retention when displaying images on the four corners, such as TV station logos and clock display.
(Settings can be made using Screen Wipe and Luminance Manager from Function MENU shown on 39 )
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniform for moving images, the occurrence of partial image
retention can be controlled. We recommend to use in combination with moving images such as a DVD.
* Please be careful since image retention will occur if display is left in a two screen display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut
and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these
portions can be expected to occur, so please be aware.
Notes
About screen defects
• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright
spots (points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface
may rise in some cases.Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface
but avoid strong impact because there is still danger of glass breakage.
About the power swivel
• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution in
households where children are present. (Refer to Power Swivel shown on 25 )
8
COMPONENT NAMES
ENGLISH
Front
Main Unit
Cabinet
(front frame)
Panel
AV monitor
Control panel
• Adjustment buttons are located
on the bottom.
• The back cover is provided
with indications to distinguish
the adjustment buttons.
Remote-control
receiver
10
Indicating lamp 21
• The main power switch is located at the back, on the
lower surface.
MENU button
INPUT SELECT button
VOLUME
(OK button)
UP/DOWN
CHANNEL
buttons 24
UP/DOWN buttons
(
ADJUST
(SELECT button) 22
buttons)
33
Main power switch
21
22
(32)
SUB-POWER button 21
(37)
(42)
• ( ) indicates the function while the MENU is displayed on the screen.
Rear
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Handgrips
Handgrips
External
speaker
terminals
External
speaker
terminals
16
16
External device connection terminals
RGB input terminals
16
9
COMPONENT NAMES (continued)
Remote control
POWER ON/OFF button
RECALL button
FUNCTION SELECT button
@@@@@@@@e?
@@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@?e
@@@@@@@@e?
@@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@
@@@@@@@@
@@h?
@@
@@h?
@@
@@h?
@@
@@h?
@@
@@h?
@@
@@h?
@@
INPUT SELECT buttons
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
DVD CONTROL button
@@g
[email protected]@
@@g
[email protected]@
@@g
[email protected]@
@@g
[email protected]@
@@g
[email protected]@
@@g
[email protected]@
@@@@@@@@
[email protected]@@@@@@@
@@@@@@@@ [email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@
[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@[email protected]@@@@@@@ [email protected]@@@@@@@
FREEZE/RETURN buttons
MENU button
OK button
SELECT/ADJUST button
PICTURE MODE button
CH I/CH II button (TV)
SOUND MODE button
VOLUME UP/DOWN button
CHANNEL UP/DOWN button (TV)
MUTE button
PROGRAM SELECT buttons
(TV)
MULTI MODE button
MULTI PICTURE button
T/TEXT button
(TV)
PHOTO INPUT buttons
SWIVEL button
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
2. Load batteries.
• Load two Size AA batteries included
observing the correct polarities.
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
With in 30
degrees
About 3m
With in 30
degrees
About 3m
About 5m
3. Close the battery cover.
• Replace the battery cover in the
direction of the arrow and snap it back
into place.
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical injury,
or stains.
10
ATTENTION
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
COMPONENT NAMES (continued)
DVD and SAT
*2
FUNCTION SELECT
RECALL (TV)
Press this button to indicate function
mode with a lamp.
*1
With this button, the display change
between “--”,“---”,“-” and AV00 on the
top right hand corner of the screen.
“--” is for 2 digit channel selection, “---”
is for 3 digit channel selection and “-” is
for 1 digit channel selection.
ENGLISH
Remote control (continued)
RECALL (Video/RGB)
Press this button to display input signal.
DVD CONTROL
You can use these buttons to operate
the selected brand of DVD player.
INPUT SELECT
Press this button to change input
mode.
SOUND MODE
FREEZE/RETURN
You may recall the sound mode by pressing
this button. Each time pressed, sound mode
is changed in following sequence.
Press this button to change the
picture to freeze mode. Press it again
to return to normal picture.
Movie
Music
Favorite
Speech
PICTURE MODE
CH I/II
This button is for A2 / NICAM
models only.
You may recall the picture mode by
pressing this button. Each time pressed,
picture mode is changed in following
sequence.
Dynamic
Natural
Cinema
MUTE
PROGRAM SELECT
Press these buttons to select a TV
program directly.
MULTI MODE
In multi-picture mode, pressing this
button will change the multi-picture
mode.
Press this button to turn off the set
sound. When press again or the
volume up button, the audio will be
restored.
MULTI PICTURE
Press this button to change the
screen to multi-pictures. Press it
again to return to normal picture.
TIME (TV)
PHOTO INPUT (37/42 only)
Pressing this button can indicate the
time by On-Screen display when
receiving a TV program on the screen
including TELETEXT service with the
time information.
Press this button to display the
pictures from digital camera and USB
card reader.
SWIVEL
ZOOM
Press this button can change Picture size.
Press this button to rotate TV. Use
cursor key (
) to select the degree
of rotation.
*1 FUNCTION SELECT button
This remote controls has functions to control DVD player, DVD recorder, and STB for certain makers, besides this set.
Press
button to operate those equipments.
Each time pressed, LED lamps (TV, DVD, SAT) left to
button lights to indicate the selection.
For details, refer to 48
*2 LED
LED lamps of DVD and SAT have 2 conditions (lighting or blinking).
Lighting: Indicate that the corresponding button becomes DVD (STB) mode.
Change to STB (TV) mode when press the
button during LED lighting.
Blinking: Indicate that DVD or STB makers can be set up.
Set up makers/types for DVD or STB during LED blinking (30 sec). For details, refer to 48
If press the button on the remote control after LED light is off, LED light becomes on the corresponding code.
11
COMPONENT NAMES (continued)
Remote control (continued)
[Button for TELETEXT Mode]
PAGE UP / DOWN button
TEXT / TV + TEXT button
COLOR buttons
(RED, GREEN, YELLOW, BLUE)
INDEX button
SUB TITLE button
CANCEL button
REVEAL button
TV / TEXT button
TELETEXT FUNCTION
Buttons on Remote Control
TV / TEXT
TEXT / TV + TEXT
INDEX
SUB TITLE
Function
This switches the receiver between the TV mode and the TELETEXT mode.
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
This selects the P100 (100 page).
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).
CANCEL
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text
page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to
display the TELETEXT screen.
RED
GREEN
YELLOW
BLUE
Each of these buttons selects a link page displayed at the lower part of the screen.
REVEAL
This allows hidden information (found on some teletext pages) to be displayed on the screen.
PAGE UP / DOWN
These buttons increase / decrease the TELETEXT page number.
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
12
INSTALLATION INSTRUCTIONS
ENGLISH
Installation
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or
dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries
or property damage caused by use of other mount units or improper installation.
CAUTION
10cm or more*
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches
: For a desktop set-up) or more between the sides and other objects such as walls, etc.,
so that the ventilation holes are not blocked.(*)
Cord or chain
Wall or Pillar
Clamp
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
Cord or chain
Wall or Pillar
Hook
Clamp
Cord or chain
Securing desktop
1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the
stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
Read SAFETY INSTRUCTIONS (
ceeding to these steps:
4
to
7
) carefully to ensure maximum safety before pro-
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
CAUTION
Loosen a cord or chain enough while operating power swivel to avoid possible physical injury.
13
INSTALLATION INSTRUCTIONS (continued)
Connecting to an Audio Visual Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the imaging device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this
device and the signal output terminal of the imaging device.
Speaker (R)
Power
cord
To composite
output terminal
To audio output
terminals
To component
input terminals
To component
output terminals
To audio
output terminals
Set-Top Box
Speaker (L)
Monitor (rear panel)
Antenna
To component To component
input terminals output terminals
DVD Player
Side Input
To USB output
terminal
To S, composite
audio output
terminal
VTR
Photo input terminal
(37/42 only)
Headphone
To composite
input terminals
To audio input
terminals
VTR
To composite
output terminals
To audio output
terminals
To S video
output terminal
To audio output
terminals
DVD Player
TV Type only
VTR
[An example of connecting audio visual devices]
• If a component input terminal and a composite input terminal of AV1 and AV2 connect to the monitor at the same time, component input would
govern.
• If a video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer video quality.
(If an S video input terminal and a video input terminal of AV3 or AV5 (side input) connect to the monitor at the same time, S video input would
govern.)
• If the OUTPUT (Monitor) terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to view the same image as on the
main unit. But it is possible to monitor only the composite video signal from AV1 ~ AV5 input or the S video signal from AV3 and AV5 that is
displayed on the screen at the time.
• The photo input function might not be provided, depending on a model.
• Secure connecting cables to the stand with the provided clamp.
HDMI*
• HDMI (High-Definition Multimedia Interface) is a digital interface based on DVI (Digital Visual Interface), which is an added function for audio
visual equipment.
– It does not have degradation by transmission since it is digital.
– With only one cable, it is possible to transmit both picture signals and audio signals.
• In case of using analog audio as connecting with DVI-HDMI transformation connector, use an analog audio terminal for AV1 input.
14
INSTALLATION INSTRUCTIONS (continued)
ENGLISH
Connecting to an Audio Visual Device (continued)
When the "ANT" terminal is connected to outdoor antenna instead of CATV system, please note that a good
antenna adaptor is necessary. See the diagram on the right.
Precautions when connecting the antenna
• Clamp section A using pliers when installing the coaxial cable. If other types of adaptors are used, be
sure that the core and shielding are good.
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel
flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on
the screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
• For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
15
INSTALLATION INSTRUCTIONS (continued)
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "Product Specifications" concerning the specifications of this device.
53 57
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask
the personal computer manufacturer or your local retail dealer.
Monitor (rear panel)
Speaker (R)
Speaker (L)
Power cable
connector
(DVI)
Power
cord
(D-sub)
Connecting to a PC Device
To signal
output
terminal
(DVI)
Connecting to an Audio Visual Device
To audio
output
terminal
To signal
output
terminal
(D-sub)
3.5mm
Stereo
mini jack
To audio
output
terminal
To signal
output
terminal
(DVI)
(Example)
DVD Player
PC
• Setting
RGB1: DVI-PC
RGB2: RGB
For details, refer to
16
56 57
• Setting
RGB1: DVI-STB
RGB2: Component
For details, refer to
55 56
INSTALLATION INSTRUCTIONS (continued)
ENGLISH
Mounting the Speaker Unit
CAUTION
Make sure that the main power swich of the monitor is turned off (standby or indicating lamp: off/red) when removing or connecting the
speaker cables.
Mounting the Speaker System to the Monitor
1. Mounting the Speaker System to the Monitor
Hook the clamps (3 pieces) into the holes as shown in the figure,
and pull them down.
Follow the step in both Right and Left sides.
Right Side
Clamps
CAUTION
Make sure to use the speaker systems fastened with the speaker
holders and the screws.
Rear of the monitor
2. Attach the speaker holders
After twisting the screws off as shown, fasten the speaker system to the monitor with the speaker holder by the screws.
The speaker holder direction is opposite on the Right and Left speaker systems.
Monitor
Right Side
Speaker
System
NOTE
In case that the speaker
systems do not fit with
the monitor body’s
height.
Speaker holder
When loosen the screws
fixing the aluminum pieces,
the speaker system is
movable up and down.
Adjust the position to the
monitor body’s height, then
tighten up the screws.
Screws x 4
Twist off
the screws
Speaker holder
Rear of the monitor
Screws x 4
Aluminum pieces
Screwdriver
Place to attach the side input.
3. Attach the speaker connecting cables to the monitor. (Make sure the ferrite core is toward the monitor side)
Treating the wire ends
Pull off while twisting
(R)
Please prepare the supplieol
speaker cables
Black
Connect the
silver
colored wire
(L)
Red
Connect the
copper
colored wire
Black
Connect the
silver
colored wire
Red
Connect the
copper
colored wire
Ferrite core
How to connect
the speaker
cables
(Moniter side)
Ferrite core
Press down
the lever
Insert the wire
Raise
the lever
17
INSTALLATION INSTRUCTIONS (continued)
Mounting the Speaker Unit (continued)
4. Attach the speaker cables to speaker systems.
How to connect
the speaker
cables
(Speaker side)
Hold down
the lever
Insert the wire
Release
the lever
Speaker
terminals
Connect the copper - colored
wire to the
Red side.
Connect the silver - colored
wire to the
Black side.
CAUTION
Make sure to secure the power cable and the connecting cables for other audio visual devices, except the speaker connecting cables, to the
clamp of the monitor stand and the rear of it. When the monitor is swiveled, the connectors might be dropped out and generate heat. It could
cause fire and/or connector failures.
18
INSTALLATION INSTRUCTIONS (continued)
ENGLISH
Mounting the Side Input
• With the speaker unit
1. Mount the side input into the speaker holder.
Hook the clamps (4 pieces) of the speaker holder into the holes as shown in the figure and pull them down until it sounds click.
Fasten the side input with the speaker holder by the screws.
Refer to 14 about the connection of side input.
See the below figure how to treat the cable.
Clamp (32)
Side input
Speaker holder
Screw x 1
Screw hole
Side input
• Without the speaker unit
Clamp (42, 37)
Clamp (42, 37)
42
inch
32 inch
37 inch
1. Attach the holder for the side input.
Holder
Screw x 2
Screw hole
2. Mount the side input into the securing holder.
Fasten the side input with the speaker holder by the screws.
See the below figure how to treat the cable.
Clamp (32)
Clamp (42, 37)
42 inch
37 inch
Side input
32 inch
19
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
Connect the power cord, after completing all other connections. ...42, 32
Connect the power cord, after completing all other connections. ...37
Connect the power cord to this device.
Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided. (Ask your local retail dealer about the power cord for AV monitor)
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
20
OPERATING INSTRUCTIONS
Indicating lamp
Main power switch
(32)
(37)
ENGLISH
Turning Power On and Off
• To turn the monitor power ON, press the main power
switch on the monitor main unit to ON, and then press
the SUB POWER button of control panel or the power
button on the remote control.
• To turn the monitor power OFF, press the SUB POWER
button of control panel or the power button on the
remote control, and then press the main power switch
on the monitor main unit to OFF.
• During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the power button on the remote control.
Indicating lamp
(42)
Indicating
lamp
Power status
Off
Off
Off
(standby)
On
When the main power switch is ON, and
the power button on the remote control
or the SUB POWER button on the
underside of the front of the frame is
ON.
Off
(Power Save)
When the main power switch is ON, and
the power button on the remote control
or the SUB POWER button on the
underside of the front of the frame is
ON.
However, the state in POWER SAVE
mode
Lights green
POWER ON/OFF
button
Lights orange
When the main power switch is set to
OFF.
When the main power switch is ON, and
the power button on the remote control
or the SUB POWER button on the
underside of the front of the frame is
OFF.
Lights red
SUB-POWER button
Operating
When the indicating lamp lights in orange or the message “No
Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on the
screen, there is something unusual about the status of reception.
See “Power Save Mode” or “Symptoms That Seemingly Appear to
be Failures.” 48
49
50
ATTENTION
• Avoid repeatedly turning the monitor on and off at short time
intervals. Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out of
use for an extended period of time.
• If a power failure occurs while the main unit is running, it would
be powered on upon recovery from the failure. Turn off the unit
main power switch before leaving the main unit.
21
OPERATING INSTRUCTIONS (continued)
RECALL button
INPUT SELECT
buttons
CHANNEL UP/DOWN buttons
INPUT SELECT button
CHANNEL
UP/DOWN button
Input Switching
• Input can be switched by pressing the AV1~6, RGB1 or
RGB2 buttons of the remote control.
• Input can be switched to TV by pressing CHANNEL
UP/DOWN buttons or PROGRAM SELECT buttons.
• Input can be switched in the sequence of TV ➝ AV1 ➝
AV2 ➝ AV3 ➝ AV4 ➝ AV5 ➝ AV6 ➝ RGB1 ➝ RGB2 by
pressing the INPUT SELECT button of the control panel.
* TV display is not available in the AV monitor.
TV AV1 AV2 AV3 AV4
PROGRAM
SELECT buttons
ZOOM button
RGB2
RGB1
AV6
AV5
Size Switching
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
• During TV/VIDEO signal input (TV, AV1, AV2, AV3, AV4,
AV5, AV6, RGB1 (set to [DVI-STB]) and RGB2 (set to
[Component]))
* TV display is not available in the AV monitor.
4:3
Panoramic
Full
Zoom
Cinema
• The size will fix as Full mode and not change when receiving the
component signal of 1080i/50, 1080i/60 or 720p/60.
Full
Display size selection diagram
When you want to
Set the display size to
Play a 4:3 image in a 16:9 screen faithfully.
4:3
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Panoramic
Play a 16:9 VISTA size image in the 4:3
image faithfully reproduced on the 16:9
screen.
Play a 21:9 Cinema size image in the 4:3
image expanded vertically on the 16:9
screen.
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and horizontally squeezed.*
22
Input signal
Display screen
Remarks
Blanking occurs on both sides.
(4:3 signal)
Zoom
(Vista)
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
remain at the top and bottom.
In some cases, some slight blanking may
remain at the top and bottom.
Cinema
(Cinema)
* An image with an aspect ratio of 16:9 shrunk
horizontally to 4:3 to display in a 4:3 screen
Full
(Squeeze)
OPERATING INSTRUCTIONS (continued)
ENGLISH
Size Switching (continude)
Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows.
1. Press ZOOM button and
SELECT buttons during picture size display.
2. Position display will appear.
3. Adjustment range of each picture size are as shown below.
[Panoramic]
- 12 to + 12
[Zoom] and [Cinema]
- 31 to + 31
4. When 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position + 31
Position - 31
Press
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV
program, the image would appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or pubic viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
• During RGB Input (RGB1 (set to [DVI-PC]) and RGB2 (set to [RGB]))
Normal
Real *
Full
Zoom3
Zoom1
Zoom2
* Real mode gives the image of the same shape as it is displayed on a computer monitor.
This mode is only available for VGA (640 X 480) and WVGA (864 X 480).
Display area selection diagram (RGB input)
Resolution
Full display
Display
Full
640 X 480
(VGA)
800 X 600
(SVGA)
1024 X 768
(XGA)
1280 X 1024
(SXGA)
1600 X 1200
(UXGA)
Circular display
Normal
Real
Zoom1
Zoom2
Zoom3
* VGA and W-VGA
only
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that
flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On 38 can
reduce the flicker.
23
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
The volume can be adjusted by pressing the
buttons of the remote control (or the
and
buttons of the monitor unit).
Audio Mute
and
volume
Volume setting value
The audio volume can be temporarily mute by pressing
the MUTE button of the remote control.
Volume setting value
Volume 15
Volume 15
Adjustment status guide display
Adjustment status guide display
(The display color will change to magenta: volume ➝ Mute)
• When a button is pressed, the volume adjustment status
guide will be displayed.
• The volume will increase when the
the guide is being displayed.
• The volume will decrease when the
the guide is being displayed.
button is pressed while
button is pressed while
• When a button is pressed, the volume adjustment status
guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the
button
while the audio is mute.
• The muting can be cancelled by pressing the
button or
MUTE button while the audio is mute.
• The audio from the headphone terminal is not mute.
• The audio from the speaker is automatically mute while
connecting the headphone to the headphone terminal of the side
input (AV5).
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
24
OPERATING INSTRUCTIONS (continued)
ENGLISH
Power Swivel
• This feature controls the motorized stand. It allows turning the plasma display left or right using the remote control.
CAUTION
Make sure that the main power switch of the monitor is turned off when removing or connecting the power cord, the connector cables, and
the speaker cables.
1. Press Swivel button.
The controlling icon appears on the screen.
• If the connecting cable is not connected, the indication "Not Available" appears.
• The swivel display disappears in about 6 seconds without any operation.
Swivel
2. Adjust for preferred angle.
Facing directions are displayed on the screen while the monitor is swiveled.
Adjust by using
key while the swivel display is on the screen.
Swiveling angle of the monitor is available within 30 degrees from the front face.
ATTENTION
• Do not add excess power by hands while using the power swivel function. It could cause troubles.
• Do not get on and/or hang down the monitor. Do not swing the monitor back and forth and around either. It could cause the failure of the
stand.
• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution in
households where children are present.
• Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the stand.
• Place the monitor on the stable location, or the swivel function would not operate correctly. It would cause the malfunction.
• In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand.
Caution when connecting the monitor with the stand
• When detach the stand from the
monitor, make sure to detach the
connector cable from the stand
connection terminal on the rear of the
monitor.
• When attach the stand to the monitor
once again, insert the connector
cable into the stand connection
terminal on the rear of the monitor.
Insert until it clicks.
Pinch right and left
locks of the connector
and pull out downward.
• Make sure that the direction of the connector for stand connecting cable is correct.
* This power swivel function might not be provided depending on a model.
25
OPERATING INSTRUCTIONS (continued)
Input Signal Screen Display
RECALL button
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control.
• The display will go out in approximately 6 seconds.
TV
Off-timer
On-timer
1
ABCDE
OFF
-- -- Min.
-- -- : -- --
VIDEO
Off-timer
On-timer
AV1
Composite
OFF
TV position
Name
Sound mode
Input mode
Signal mode
-- -- Min.
-- -- : -- --
RGB
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
Off-timer
On-timer
26
OFF
-- -- Min.
-- -- : -- --
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
ENGLISH
OPERATING INSTRUCTIONS (continued)
RECALL button
INPUT SELECT
buttons
SELECT/ADJUST
button
( , , , )
CHANNEL
UP/DOWN button
Displaying MULTI PICTURE
If the MULTI PICTURE button on the remote control is
pressed, multi pictures will display. And then three types
of the screen can be selected by pressing the MULTI
MODE button on the remote control.
The multi picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
2 pictures (Split)
4 pictures
MULTI MODE
button
MULTI PICTURE
button
12 pictures
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons; the audio will be
output from the side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the CHANNEL UP/DOWN buttons on the remote control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be
selected by pressing INPUT SELECT button on the remote control.
• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.
• Refer to the table for 2 pictures (Split) mode. 28
• For AV monitor model, TV screen cannot be displayed.
5
AV1
A
B
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
• Press
and
SELECT buttons to select picture A or picture B indicated by a red triangle. For pictures
on right, press and
SELECT buttons to select picture. The input display on the selected picture would
change green.
• The TV channel can be changed by pressing the CHANNEL UP/DOWN buttons on the remote control.
• The audio can only be output from picture A in 4 pictures mode.
• The component signal input mode cannot be selected in pictures B. Refer to the table for 4 pictures
mode. 28
• Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 4 pictures.
• For AV monitor model, TV screen cannot be displayed.
AV1
A
B1
8
B2
6
B3 11
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
• This function activates only in TV mode.
• After several seconds, it refreshes the picture one by one.
• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode.
• This function is not provided for AV monitor model.
1
2
3
4
5
6
7
8
9
10
11
12
27
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE (continued)
Activating the Split mode from the video input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
AV1
AV2
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons. The audio of
the video will be output from the side on which the speaker icon is located.
• The same video input mode cannot be selected for both screens at the same time.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• Refer to the table for 2 pictures (Split) mode.
Activating the MULTI PICTURE mode from the RGB input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB) input.
• The speaker icon can be shifted left and right by pressing the
and SELECT buttons. The audio of the
video will be output from the side on which the speaker icon is located.
• The sub-screen position can be selected up and down by pressing
and
SELECT buttons.
• The sub-screen can be selected with the AV1AV6, TV channel buttons from the status that the speaker
icon appears on the left side of AV✱ etc. as shown in the diagram to the right.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when sub-screen is the component signal of
1080i/50 or 1080i/60.
RGB2
AV1
(Subscreen)
AV1: Displays the VIDEO input signal of the sub-screen.
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change
to power save mode.
• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.
2 Pictures (Split)
Input terminal
AV1AV5
Sub
Main
AV1
AV5
AV1
AV2
AV6
RGB1
RGB2
TV
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
1080i/60
720p/60
STB
Component
TV
AV1, AV2, AV6
RGB1
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB
SECAM NTSC4.43 576p 480p
RGB2
Component
TELE
TEXT
Main
Sub
( : Available)
Teletext is available only for TV
4 Pictures
Input terminal
AV1AV5
Sub
Main
AV1
AV1
AV2
AV6
RGB1
RGB2
TV
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
1080i/60
720p/60
STB
Component
TV
AV1, AV2, AV6
RGB1
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB
SECAM NTSC4.43 576p 480p
RGB2
Component
TELE
TEXT
Sub 1
Sub 2
Sub 3
( : Available)
28
Main
ENGLISH
OPERATING INSTRUCTIONS (continued)
FREEZE button
Picture Freezing
[Split]
5
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
A
• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the “Freeze
Mode” setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and the
other still.
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function [Strobe]
1
as below:
TV
PAL, SECAM
NTSC3.58/4.43
576i
480i
576p
480p
1080i/50
1080i/60
720p/60
RGB, DVI-PC
Split
Strobe
B
2
3
4
5
6
7
8
9
10
11
12
Active
( : Available)
29
OPERATING INSTRUCTIONS (continued)
ROTATE button
PHOTO button
PHOTO INPUT button
SLIDE SHOW button
Photo Input Display (37/42 only)
With the PHOTO button on the remote control, the pictures from a digital camera or Card Reader can be displayed.
Digital Camera
USB cable
USB Card Reader
Operating the Photo Input
1. Make sure that the power switch of the monitor is turned off/standby before using.
2. Set up the digital camera and its power in reference to the item relating to “connecting to PC” on the user manual of digital camera.
*Insert the memory card when use the USB Card Reader.
3. Connect the monitor with the USB cable (see the above picture). Switch the input to the photo input by pressing PHOTO button. Then, turn
on the power of the digital camera.
(Refer to the user manual of your digital camera).
4. The photo pictures will be displayed after a period of time turning on the camera, if connecting normally.
30
OPERATING INSTRUCTIONS (continued)
ENGLISH
Photo Input Display (37/42 only) (continued)
Photo Input Function
Buttons on Remote Control Function
Operating
PHOTO
Display the pictures in the thumbnail view.
Return to the previous input display during the
thumbnail or the full view.
Thumbnail-Size Image
• Select the pictures by using (
,
,
,
) key.
• Display the next or previous thumbnail-view of 16 images per one
page by using (+), (–).
• Display the selected picture in the full size by pressing
button.
Full-Size Image
• Return to the thumbnail-view by pressing
button or return button.
ROTATE
Press this to display the picture with rotate mode.
• Each time pressed, the picture is rotated in the sequence of 90° ➝ 180°
➝ 270° ➝ 0°.
Press this to display the slide show of pictures.
• Press the button while displaying the picture, the slide show begins from
the first picture at a fixed interval.
• Press OK key, the slide show will be paused with OSD display [ OK start].
The slide show starts if let the condition for a minute.
• Return to the thumbnail images when finishing the all of pictures.
• Interval time during slide show can be changed from 5, 10 and 30
seconds in “Slide Interval” of function menu. 39
SLIDE SHOW
1/ 6
2/ 6
5/ 6
6/ 6
3/ 6
4/ 6
No.
1/
6
28/05/03
1600 × 1200
Thumbnail-Size Image
Full-Size Image
• Specification
Application
Digital Camera corresponding to DCF standard.
USB Card Reader with the memory containing pictures had taken by camera.
Max number of picture
500
Max number of pixel
8176 x 8176 JPEG format
• Error Information
PHOTO INPUT
Information
Accessing
No message
Normal
No message
Not insert USB
“No Connection”
Not available format
“No Connection”
Abnormal
“No Connection”
No File
“No File”
Loading Files
“Loading”
31
OPERATING INSTRUCTIONS (continued)
Photo Input Display (37/42 only) (continued)
CAUTION
• The picture may not be displayed in case of editing by computers.
• Do not connect any apparatus other than a digital camera and a USB card reader to the photo input connector. It causes the malfunction.
• Do not connect a digital camera and USB card reader with USB HUB. Pictures may not be displayed correctly, or it causes the malfunction.
• Insert only one memory even though the USB card reader has multiple slots for memory card. Pictures in multiple memory cannot be seen
at the same time.
• Certain types of digital cameras or card readers may not work with this photo input function.
• Digital cameras with low battery power may not properly display photos in this input.
• This function does not work for audio and moving images taken other than a digital camera.
• Response time might vary according to each image content when switching pages.
• Contrast will decrease automatically if stationary images such as digital still photos are left on the screen for more than 3 minutes.
• The OSD message “No Connection” is displayed in case of the incomplete connection with USB cable and connection to a digital camera
or USB card reader without the memory card.
• The menu items other than “Picture” and “Function” are not available with grayed-out display.
• The functions of the multi picture, CH selection, freeze mode, aspect, mode display, and so on are not available.
• During blinking LED which indicates the access of a digital camera or USB card reader, or displaying “Loading”, do not turn the power
off/standby mode nor remove/insert USB cable and memory card.
• The picture may not be displayed correctly, depending on the connecting device in case of extending the USB cable.
* This photo input function might not be provided depending on a model.
32
OPERATING INSTRUCTIONS (continued)
MENU button
RETURN button
OK button
SELECT/ADJUST
buttons
( , , , )
Using the Menu Screen
(On-screen display system)
ENGLISH
RECALL button
When the MENU button is pressed, the adjustment menu
screen will be displayed; from there, PC signal
adjustment and setting is possible by using the SELECT
button, ADJUST button and OK button.
• Refer to
settings.
34 -
46
concerning the adjustment items and the
Example: Selecting the Picture screen
1. Press the MENU button to display the Main Menu
screen.
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
2. Press the OK button to display the Picture Menu
screen. (Use the
and
SELECT buttons to select
other items.)
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Exit
3. Use the
and
SELECT buttons to select the item to
be adjusted and then use the
and
ADJUST
buttons to adjust (example: Contrast).
Contrast
Next / Prev
+ 31
Adjust
Return
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the Adjustment
Menu screen will be closed automatically.
33
OPERATING INSTRUCTIONS (continued)
SETUP MENU (TV mode)
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Off
Return
Off
Return
Setup
Manual Tuning
Position
Frequency
Name
Sound System
Color System
Skip
NR
Antenna Att.
Select
Return
99
250MHz
ABCDE
BG
Auto
Off
Off
Off
Exit
Setup
Fine Tuning
Select
Prog.No.199
+56
Return
34
Position
Set
Setup
Auto Tuning
Mode
Search
Select OK Set
Return
Position
Return
Off
Return
Off
Return
Setup
Sort
Position
100
101
102
103
104
105
106
107
Select
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Adjust
Setup
Auto Tuning
Mode
Search
Select
Off
Return
Name
ABCDE
BBC1
----BBC
FGHIJ
XYZAB
---------
Setup
Auto Tuning
MHz
62MHz
83MHz
97MHz
106MHz
175MHz
189MHz
199MHz
225MHz
Scanning Channel Number: 33
Cancel
OK
Return
Exit
Setup
Teletext Language
West Europe
East Europe
Cyrillic
Greek/Turkish
Select
Return
Exit
Cancel
OPERATING INSTRUCTIONS (continued)
Selected characters
ENGLISH
SETUP MENU (TV mode) (continued)
Setup hint
Auto Tuning
Position
Mode
Select the channel entry method between position setting or direct
setting. And press the OK button to fix it.
• If [Position] is selected, the screen display will be numbers (1~199
and AV00).
• If [Direct] is selected, the screen display will be C✱✱ at the channel 0~99 and S✱✱ at the channel 100~199.
Direct
Search
–
–
Press the OK button and it starts the auto tuning.
Position
–
–
Set the position number(0~199) or channel number(C✱✱, S✱✱) by
(+) (–) CHANNEL UP/DOWN buttons.
Frequency
–
–
• If [Position] has been selected, search the frequency here by
pressing
and
buttons.
• If [Direct] has been selected, this function will be not available
(grayed out).
Manual Tuning
Name
( :a letter)
Auto
Sound System
Color System
This is used to input the name of the TV station within 5 letters. After
fixing the cursor on the first digit, select a letter by
and
SELECT buttons and move to next digit by
ADJUST button.
Press the OK button again after finished.
• Selectable letters are “0”~”9”, ”A”~”Z”, “+”, “–”, ” ”(blank),
”,”(comma) and ”.”(period) .
M
DK
Auto
PAL
NTSC3.58
BG
Select the sound system through the 5 different settings.
I
SECAM
NTSC4.43
Select the color system through the 5 different settings.
Skip
Off
On
If this is set to On, that position will be skipped while selecting positions by CHANNEL UP/DOWN buttons.
This is automatically set to On for those non-broadcasting channels.
NR
Off
On
If this is set to On, it helps to reduce the noise interference visible on
the screen, especially in the weaker signal reception areas.
Antenna Att.
Off
On
If this is set to On, it helps to reduce the noise interference visible on
the screen in case of strong airwave.
After completing the fine-tuning, press the RETURN button to exit
Increasing the frequency data
this mode.
for the main tuner.
• The variable range is -56 ~ +56.
Fine Tuning
Decreasing the frequency
data for the main tuner
Sort
(When the Mode in Auto Tuning menu is set to [Direct], this function will be not available (grayed out).)
(A Line of position List)
–
–
Press OK button at the a line that is required to change order, then
the characters will change to green. And move it up or down in the
list by pressing
and
SELECT buttons. And press OK button
to complete it. Press the RETURN button to exit.
Teletext Language
–
–
Select the teletext language through the 4 settings.
• Select West Europe when watch in Singapore, Australia, Malaysia,
and so on.
Auto Off
Off
On
If this is set to On, the power will be turned off when there is no
transmission signal and no operation for about 10 minutes in the TV
mode.
35
OPERATING INSTRUCTIONS (continued)
SETUP MENU (Video mode)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Setup
System
Color System
Video Input
RGB1
RGB2
Select
OK Set
Setup
System
Color System
Video Input
RGB1
RGB2
Select
Selected characters
OK Set
System 1
DVI-STB
Component
HDTV
Return
System 1
DVI-STB
Component
HDTV
Return
Setup
Color System
AV1
AV2
AV3
AV4
AV5
Auto
PAL
SECAM
PAL
Auto
Select
Return
Exit
Setup
Video Input
AV1
AV2
Auto
Auto
Select
Return
Exit
Setup hint
System1
System
System2
Do not change the original setting.
(System1 : Europe/Asia, System2 : North America)
Color System
AV1~AV5
System1
Auto
PAL
SECAM
NTSC3.58
NTSC4.43
System2
Auto
PAL-N
NTSC-M
PAL-M
This should correspond to the color system of the signal from the equipment that is connected to AV1~AV5 video input terminal.
• Normally, set this to Auto. The system of the input signal will be automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
• When the component signal is received, this would be not available
(grayed out).
Video Input
AV1, AV2
HDTV
RGB1
DVI-PC
RGB2 (1st step)
RGB
RGB2 (2nd step)
36
Auto
Auto
SDTV/DVD
This should correspond to the signal mode of the signal from the equipment that is connected to AV1, 2 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
DVI-STB
This should correspond to the signal mode of the signal from the equipment that is connected to RGB1 DVI terminal.
Component
This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.
HDTV
SDTV/DVD
This step should be set only when [Component] is selected on the 1st
step.
This should correspond to the signal mode of the signal from the equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
OK Set
Select
ENGLISH
SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB))
Adjust
0
+ 31
– 20
10
Reset
Return
Horizontal Position
Next / Prev
Adjust
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
OK Set
Select
Selected characters
Auto Adjust*
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Return
Adjust
0
+ 31
– 20
10
Reset
Return
Clock Phase
Next / Prev
Setup
Input Level
Frequency Display
WVGA Type
WXGA Mode
Vertical Filter
Frequency Mode
RGB1
RGB2
Select
Set
0
10
Adjust
Return
0.7V
Off
Off
Off
On
Movie
DVI-PC
RGB
Return
Setup hint
Adjust
–
Pressing the OK button here,
Automatic regulation is started.
Moves the horizontal position Moves the horizontal position
to left.
to right.
Horizontal Position, Vertical Position, Horizontal Clock and Clock
Phase are adjusted automatically.
Adjust the left-side display position.
Screen display changes to Magenta color if beyond the available
range. (This function is only for RGB2. It’s not available (grayed out)
for RGB1 (DVI-PC).)
Moves down the vertical posiMoves up the vertical position. Adjust the vertical display position.
tion.
Screen display changes to Magenta color if beyond the available
range. (This function is only for RGB2. It’s not available (grayed out)
for RGB1 (DVI-PC).)
Increases the dot clock freReduces the dot clock frequency (expands the right Adjust for maximum character clarity.
quency (shrinks the right side).
side).
(This function is only for RGB2. It’s not available (grayed out) for
RGB1 (DVI-PC).)
Slows the dot clock phase Advances the dot clock phase
Adjust for clear character visibility.
(shifts slightly to left).
(shifts slightly to right).
(This function is only for RGB2. It’s not available (grayed out) for
RGB1 (DVI-PC).)
(off the function)
(waiting to reset)
0.7V
Input Level
1.0V
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Normally set to 0.7 V. If white is found to spread across the screen,
set to 1.0 V. (This is effective only for RGB2.)
Frequency Display
Off
On
Set this to Off if the frequency information of the Input Signal Screen
Display is not required.
WVGA Type
Off
On
This is only available for W-VGA signal.
When it is set to On, the display area mode can be selected Full or
Real. (With RGB1 INPUT, the screen remains the same. RGB2 (ANALOG) INPUT only)
WXGA Mode
Off
1280x768
1366x768
This is only available for W-XGA signal.
(RGB2 (ANALOG) INPUT only)
37
OPERATING INSTRUCTIONS (continued)
SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB)) (Continued)
Selected characters
Setup hint
Vertical Filter
Off
Frequency Mode
Movie
PC
RGB
RGB2 (1st step)
Auto
Turn On when concerned about screen flicker.
Set to Movie when viewing moving images on a personal computer.
DVI-STB
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
Component
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
DVI-PC
RGB1
RGB2 (2nd step)
On
HDTV
SDTV/DVD
This step should be set only when [Component] is selected on the
1st step.
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will
be automatically recognized.
• If the input signal contains much noise or has a low level at Auto
and the operation is found erratic, set this to match the input signal.
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
38
OPERATING INSTRUCTIONS (continued)
ENGLISH
FUNCTION MENU
AV monitor only
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Panel Life
Luminance Manager
Slide Interval
Reset
Select
Set
Off
On 60Min.
Off
Off
Split
Panoramic
Nomal
Off
5Sec.
Reset
Return
Selected characters
Screen Saver
Screen Wipe
Function
Mode Display
ID Number
Inverse
Standby White
Gamma
Reset
Select
Set
Off
1
On 60Min.
Off
2.2
Reset
Return
Setup hint
Off
60Min.
5Min.
40Min.
10Min.
20Min.
On
60Min.
This moves the picture around the screen in small amounts, at set
intervals, to reduce the panel image retention. This is where stationary objects, such as screen logos, leave a slight image visible after
they should have disappeared.
This is used to reduce the panel image retention that can occur with
stationary pictures by the white field signal. Select On (continuous
operation) or 60 Min. (time limit operation) and press the OK button.
Press the MENU or RETURN button on the remote control to return to
normal viewing.
Black Side Panel
Off
On
This turns the gray sidebars to the black sidebars when watching
normal mode screen size area. It is always set to Off when the monitor
powered On. It is recommended to set to Off to reduce the panel
image retention. This is not available for the photo input function.
Video Power Save
Off
On
This is used to reduce power consumption for video input when there
is no video signal. Setting it On will lead the monitor to the standby
mode when the AV input with no signal is selected.
Split
Freeze Mode
Panoramic
Default Zoom
Panel Life
Normal
Off
Slide Interval
Reset
5Sec.
10Sec.
Off
1
Standby White
Gamma
30Sec.
3
6
4
5
On
Off
This is used to display images at set intervals during slide show.
(37/42 only)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
This can display the Input Signal Screen Display every time the input
mode and signal mode are changed.
Set to OFF if the Input Signal Screen Display is not needed when
switching signals.
On
2
7
This function is to suppress the contrast of the screen regardless of the
Contrast setting in the Picture Menu. By this control, power consumption
can be reduced or degradation of a panel can be mitigated. The order
of power consumption is Extend 2 < Extend 1 < Normal.
If the Contrast setting is changed when this item is set to Extend 1 or
2, it will be changed to Normal automatically.
This is used to reduce the panel image retention which is caused by
especially displaying TV station logo.
Brightness of 4 corners of the panel get lower than the center.
(waiting to reset)
Mode Display
Inverse
Extend 2
On
(off the function)
ID Number
This selects the screen display size of TV input that appears first
when the main power turned on. This is grayed out and not available
in the AV monitor.
4:3
Extend 1
Luminance Manager
This selects the display condition of the FREEZE mode between Split
(2 pictures) and Strobe (12 pictures). This is grayed out and not
available in the AV monitor.
Strobe
60Min.
Assigns ID numbers to the monitors so that they can be controlled
individually (up to 7 monitors can be controlled).
This function can change each level if RGB signal invert to reduce
the panel image retention. When this function is required to use,
select On (continuous operation) or 60Min. (time limit operation) and
press OK button. And press the Menu or return button to exit.
15Min.
30Min.
120Min.
60Min.
This function is also provided against the image retention. If time is
set for this item, the screen changes into the white pattern when the
monitor enters power save mode, and it will continue for the period of
setting time.
2.2
Normally set to 2.2.
2.8
39
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (TV/Video mode)
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Picture Mode
Next/Prev
Select
Dynamic
Return
Picture
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Contrast Mode
Next/Prev
Select
Normal
Return
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
YNR
Next/Prev
Off
Select
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Auto Color
Next/Prev
On/Off
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
Dynamic
Return
Dynamic
Return
Magenta
Red
Yellow
Green
Cyan
Blue
On
Reset
Return
On
+ 60
+ 30
0
+ 60
+ 30
0
Reset
Return
On/Off
Picture
Color Decoding
RGB
Red
Green
Color
Tint
R
G
Select
B
0
+ 60
0
+ 31
Reset
40
Return
Picture
Color Management
Return
Dynamic
Off
Picture
Color Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
Reset
Select
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
Return
Reset
Return
Exit
OPERATING INSTRUCTIONS (continued)
Selected characters
Setup hint
Dynamic
Picture Mode
Natural
Cinema
Dynamic: This setting is best for very bright ambient lighting.
Natural: This setting is for normal lighting conditions.
Cinema: This setting is best for watching movie.
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
SELECT
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For normal viewing we recommend that the Contrast is set to [+31].
"Panel Life" in the Function Menu should be set to Normal when this
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to preference.
Color
Decrease color intensity.
Increase color intensity.
Adjust to preference.
Sharpness
Soft
Sharp
Normally set to Centre position Shift to the minus (-) side for a softer
effect and plus (+) for sharper picture.
Tint
Enhances red and weakens
green.
This is not available to adjust when receiving PAL/SECAM signal.
Enhances green and weakens
Then the character will be grayed out.
red.
Adjust for most realistic skin color.
Color Temperature
Cool
Normal
Warm
Normal
Contrast Mode
Auto
(off the function)
Reset
YNR
Black / White
Dynamic
(waiting to reset)
Off
Low
Normally set to Cool.
Dynamic:Emphasizes the differences between video shadings to
improve the feeling of contrast.
Normal : The gradation of an image is reproduced as faithfully as
possible.
Auto:Detects image brightness and automatically adjusts for natural
brightness.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Performs picture signal noise reduction. Turn up to reduce noise.
High
Performs color signal noise reduction. Turn up to reduce noise.
And it will be fixed as Off only when selecting DVI-STB mode.
CNR
Film Mode
Off
On
On:Automatically detects the movie film material and faithfully
reproduces the original film image.
Off:Set to OFF when switching between images does not appear
natural.
PAL Comb Filter
Off
On
This is available only when receiving a PAL composite signal. Turn
On to reduce the discolorations in fine picture detail and provides
purer color.
LTI
Adjusts the sharpness of the picture signal.
Off
CTI
Low
Middle
High
Black Enhancement
Adjusts the sharpness of the color signal.
Adjusts the black level compensation.
Auto Color
Off
On
This is available only when receiving an NTSC composite/S.Video
signal. This monitors and adjusts the color to maintain constant color
levels. It also maintains natural flesh tones while preserving fidelity of
background colors.
Color Temp. Adjustment
Off
On
Turn On when you wish to change color temperature depending on
the user's preference.
Amplitude
Cut Off
ENGLISH
PICTURE MENU (TV/Video mode) (continued)
Red
Brighter scene is decreased
in reddish color.
Brighter scene is increased in
reddish color.
Green
Brighter scene is decreased
in greenish color.
Brighter scene is increased in
greenish color.
Blue
Brighter scene is decreased
in bluish color.
Red
Dark scene is decreased in
reddish color.
Brighter scene is increased in
Adjust color temperature depending on the user’s preference. These
bluish color.
settings are independently stored in each of the 4 Color Temperature
Dark scene is increased in
modes.
reddish color.
Green
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Blue
Dark scene is decreased in
bluish color.
Dark scene is increased in
bluish color.
41
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (TV/Video mode) (continued)
Selected characters
Setup hint
Off
Color Management
Magenta
Magenta is weakened.
Magenta is strengthened.
Red is weakened.
Red is strengthened.
Yellow
Yellow is weakened.
Yellow is strengthened.
Green
Green is weakened.
Green is strengthened.
Cyan
Cyan is weakened.
Cyan is strengthened.
Blue
Blue is weakened.
Blue is strengthened.
Red
Color Decoding
RGB
R
G
B
Darkens red only.
Lightens red only.
Green
Darkens green only.
Lightens green only.
Color
Decrease color intensity.
Increase color intensity.
Enhances red and weakens
green.
Enhances green and weakens red.
Red
Tint
42
Turn On when the original balance of each color is required to adjust
depending on the user’s preference.
On
This adjusts listed colors individually to make them either deeper or
more pure. These settings are independently stored in each of the 4
Color Temperature modes.
Select the single color screen when that is required to adjust R/G/B
level individually depending on the user’s preference. And set it back
to RGB mode that indicates all color after adjusting.
Press the OK button every time the setting is changed.
This adjusts R/G/B level or tint to make the color appear natural for
the user’s preference. These settings are independently stored in
each of the 4 Color Temperature modes.
This does not work for receiving PAL/SECAM signal.
Guide display become unavailable to select with gray color.
OPERATING INSTRUCTIONS (continued)
MENU
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
OK Set
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
OK Set
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
OK Set
Select
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Return
:
:
:
:
:
:
Contrast
Next / Prev
+ 31
Adjust
Return
+ 31
– 31
0
+ 31
Off
Normal
Reset
Return
:
:
:
:
:
:
ENGLISH
PICTURE MENU (RGB mode)
+ 31
– 31
0
+ 31
Off
Normal
Reset
Return
Selected characters
Color Temperature
Next/Prev
Select
Picture
Color Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
Normal
Return
On
Reset
Return
Setup hint
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
SELECT
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For brighter scene some parts of the picture might not be clear. We
recommend to set at [+31].
"Panel Life" in the Function Menu should be set to Normal when
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to preference.
Color
Decrease color intensity.
Increase color intensity.
Adjust to preference.
Tint
Enhances red and weakens
green.
Enhances green and weakens red.
This is not available to adjust when receiving PAL/SECAM signal.
In this case the character will be grayed out.
Adjust for most realistic skin color.
Off
Picture Enhancement
Color Temperature
Cool
Low
Normal
Amplitude
Cut Off
Reset
Warm
Off
Color Temp. Adjustment
Middle
High
Black / White
On
Red
Brighter scene is decreased
in reddish color.
Brighter scene is increased
in reddish color.
Green
Brighter scene is decreased
in greenish color.
Brighter scene is increased
in greenish color.
Blue
Brighter scene is decreased
in bluish color.
Brighter scene is increased
in bluish color.
Red
Dark scene is decreased in
reddish color.
Dark scene is increased in
reddish color.
Green
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Blue
Dark scene is decreased in
bluish color.
Dark scene is increased in
bluish color.
(off the function)
(waiting to reset)
Sets the clarity of small details to the desired level.
Normally set to Normal.
Turn On when you wish to change color temperature is required to
adjust depending on the user’s preference.
Adjust color temperature depending on the user’s preference. These
settings are independently stored in each of the 4 Color Temperature
modes.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
43
OPERATING INSTRUCTIONS (continued)
AUDIO MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Audio
Audio Mode
Treble
Bass
Balance
Dynamic Bass
Matrix Surround
Perfect Volume
Reset
Select
Set
:
:
:
:
:
:
:
Movie
+ 10
– 10
0L
Middle
Off
Off
Reset
Return
R
Audio
Headphone Volume : + 20
Headphone Select : A/B
Select
Selected characters
Audio Mode
Movie
Music
Speech
Favorite
Movie: This selects the audio suitable for Movie.
Music: This selects the audio suitable for Music.
Speech: This selects the audio suitable for News, Talk show etc.
Favorite: This mode should be adjusted depending on user’s preference.
Suppresses treble.
Enhances treble.
Adjust to preference.
Bass
Suppresses bass.
Enhances bass.
Adjust to preference.
Balance
Suppresses right-side sound. Suppresses left-side sound.
Off
Low
Middle
High
Adjust to preference.
Dynamic Bass takes advantage of the ability of the human ear to be
able to distinguish between two different tones. By using this ability,
Dynamic Bass gives enhanced bass sound that otherwise would not
be heard. Adjust it depending on the user’s preference.
Matrix Surround
Off
On
This features the spacious sound effects of a stadium.
Perfect Volume
Off
On
This will automatically adjust volume so each channel and input has
the same average volume level.
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Headphone Volume
Turns down the volume.
Turns up the volume.
This is to set the volume for headphone. The audio from the speaker
is mute when connected to headphone terminal.
Headphone Select
44
Return
Setup hint
Treble
Dynamic Bass
Set
A/B
B
A/B: During the 2 picture mode, the audio will be output from
headphone on A (left picture) or B (right picture) to be selected. The speaker icon is located on the selected picture.
B: The audio of B (right picture) is from headphone.
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Timer
Off Timer
On Timer
Select
Selected characters
Off Timer
On Timer
Adjust
ENGLISH
TIMER MENU
:
30Min.
: --:-Return
Setup hint
--Min.
30Min.
60Min.
120Min.
90Min.
--(:--)
hours
(- - : ) - minutes
This function automatically sets the power to standby status when the
indicated time period has elapsed.
This automatically sets the power from standby to ON when the indicated time period has elapsed. The settable time is 00:00~11:59. Input
the required time by ▲ and ▼ SELECT buttons on the remote control.
LANGUAGE MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Language
English
Select
Return
Exit
Select a language by ▲ and ▼ SELECT buttons and press the OK button.
45
OTHER FUNCTIONS
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Picture Mode
Contrast
Brightness
Color
Shapness
Tint
Color Temperature
Contrast Mode
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Color Temp. Adjust
R Amplitude
G Amplitude
B Amplitude
R Cut Off
G Cut Off
B Cut Off
46
For every Color Temperature, 1
setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
Magenta 1 setting is registered.
Red
Yellow
Green
Cyan
Blue
Color Decoding
Red For every Color Temperature, 1
Green setting is registered.
Color For every input function and every
Picture Mode, 1 setting is
Tint registered.
Audio Mode
1 setting is registered.
Treble
For every Audio Mode, 1 setting is
Bass
registered.
Balance
1 setting is registered.
Dynamic Bass
For every Audio Mode, 1 setting is
Matrix Surround
registered.
Perfect Volume
Headphone Volume
Headphone Select
Color Management
Audio
Registration condition
1 setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
Menu
Display
Function Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Panel Life
Luminance Manager
Slide Interval
Mode Display
ID Number
Inverse
Standby White
Gamma
System
Setup
Color System
AV1
AV2
AV3
AV4
AV5
Video Input
AV1
AV2
RGB1
RGB2
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Input Level
Frequency Display
WVGA Type
WXGA Mode
Vertical Filter
Frequency Mode
Language
Registration condition
1 setting is registered.
(not registered)
1 setting is registered.
1 setting is registered.
1 setting is registered.
For every input function, 1 setting
is registered.
1 setting is registered.
(not registered)
For every signal Mode, 1 setting is
registered. (Only for RGB2)
1 setting is registered.
1 setting is registered.
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals with which
all the elements are the same or similar will be handled as the
same signal.
OTHER FUNCTIONS (continued)
ENGLISH
Audio Switching
A2 / NICAM / Sound Multiplex (TV mode)
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
BILINGUAL / DUAL sound broadcast
NICAM [II]
When bilingual program is received, sound mode display appears in yellow as shown on
right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or ▼ (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Yellow
Green
Yellow
NICAM signal received
[I]
[II]
Yellow
Yellow
NICAM [II]
NICAM [I]
Select I, II or
Green
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
8
When a stereo program is received, sound mode display will appear in red, and you can
press the CH I / II button to select between stereo and mono sound.
Each time the button is pressed,
or ▼ (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
NICAM
Select
or
Red
Green
(force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
When a monaural program is received, sound mode display will appear in green.
You can press the CH I / II button to select the sound mode between monaural and forced
mono (sound is same).
Each time the button is pressed, or ▼ (force mono) appear cyclically on the screen.
8
NOTE
• If sound signal is not strong enough for quality reception, press the CH I / II button until ▼ appears on the screen to receive a clear mono sound.
• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until ▼ appears
on the screen to receive a clear mono sound.
47
OTHER FUNCTIONS (continued)
Power Save Mode
When the RGB1, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
No
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
245W (32)
320W (37)
380W (42)
3W or less (RGB1)
1W or less (RGB2 ; 100V≤AC≤120V)
3W or less (RGB2 ; 120V<AC<240V)
Returning to operating status
• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.
DVD Player/STB Selection
• You can use this remote control to operate the selected maker of DVD player by pressing the following buttons on the remote control
simultaneously.
<“DVD” Selection>
Makers of DVD player
Set Maker
Set Type
Makers of DVD player
RCA
Set Type
HITACHI
1
1 ~ 3
FUNAI
2
1
Pioneer
3
1 ~ 6
ONKYO
RED
Panasonic
4
1 ~ 4
ZENITH
GREEN
1
TOSHIBA
5
1 ~ 4
THOMSON
YELLOW
1
Philips
6
1 ~ 2
SHINCO
BLUE
1
JVC
7
1
SKYWORTH
1
SAMSUNG
8
1
BUBUKO
1
Sony
9
1 ~ 4
2-4-12
<“SAT” Selection>
Makers of STB player
Set Maker
0
Set Type
HITACHI
1
1 ~ 2
TOSHIBA
2
1
DGTECH
3
1
Panasonic
4
1
DENON
1
1
Mitsubishi
1 ~ 2
Sharp
48
Set Maker
1 ~ 3
1 ~ 2
OTHER FUNCTIONS (continued)
ENGLISH
DVD Player/STB Selection (continued)
Set up hint
Example) HITACHI DVD To operate HITACHI DVD player, press and hold the
button,
followed by the button.
1. Press
button to indicate the lamp of DVD on the remote
control.
During LED lighting, press
and to set up the maker.
2. Release the button once while keeping
button, press
the button again to set the maker type.
* After set up the maker type, press the button related with
DVD, and make sure that DVD player is working. In case
DVD player does not work, repeat 1 and 2 with other
numbers for the maker type to make sure it. (In this example,
press or .)
NOTE
• Not all models of the listed makers can be operated using
this remote control.
Signal Check (RGB mode)
Changes in the signal status are displayed on the screen as they arise.
Status
Display
When Mode Display is set to ON,
the input signal is switched or
when the RECALL button is
pressed.
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
RGB
Action
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
OFF
When the sync signal is no
longer detected.
When the input signal does not
match the monitor specifications
or is in an unstable status.
• A guide displays No Sync.
Signal, and Power Save (for
approx. 5 sec.)
• When the condition continues
where the sync signal cannot
be detected, indicator lamp of
power source changes in
orange and the mode switches
to power save mode.
Recheck the personal computer
power switch status and the
connection status.
A guide displays Invalid Scan
Freq.
Recheck the input signal
specifications.
-- -- Min.
-- -- : -- --
! No Sync. Signal
54
~
57
! Invalid Scan Freq.
49
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating lamp
off.
• Check the way the power cable is connected.
• Press the power switch.
See page
20
21
• The message “No Sync. Signal” or “Power
Save” is displayed.
! No Sync. Signal
• No picture with the power indicating lamp
lights in orange.
• The message “Invalid Scan Freq.” is displayed.
! Invalid Scan Freq.
No sync signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging equipment,
etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
• Check the way the signal cable is connected.
16
16
55
56
57
• The power indicating lamp is normally lit but
no picture.
• Check the contrast and brightness settings (adjust them for higher
contrast and brightness).
• Check the way the signal cable is connected.
16
41
43
• The display image appears flowing slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot
clock frequency first, the dot clock phase next.)
(RGB input)
• Text displayed across the screen appears
blurred.
• A fine pattern flickers when displayed on
the screen.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control in
opposite direction.
• Check to see if the batteries in the remote control are OK.
• The display image does not appear in the
normal position.
37
52
37
52
AAAAA
• Check to see if the displayed input signal match the monitor specification by pressing
button.
• Turn off the screen saver.
10
16
39
55
56
57
• The display has picture missing on the
screen.
(PC input mode only)
• The temperature of the display panel surface is high.
50
AAAAA
• Turn off the screen saver.
39
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may cause the
temperature of the panel surface to increase. Please note that this
is not a malfunction.
–
TROUBLESHOOTING (continued)
Symptom
Point to check
• There are locations on the screen that are different from
the periphery (*).
*Points that do not light, points with brightness different
from that of the periphery, points with color different from
that of the periphery, etc.
• High-precision technology is used to manufacture the plasma
display panel, However in some cases, there are minor defects in
some parts of the screen. Please note that this is not a
malfunction.
• Vertical stripes appear, depending on the screen contents.
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. Depending on the screen
contents, in rare cases this may cause vertical stripes to appear
because of failure to light. Please note that this is not a
malfunction.
See page
–
–
• Coarse horizontal stripes appear in FULL display.
• Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
37
• Flickering in the form of horizontal lines oscillating up and
down.
(PC INPUT MODE only)
• If the direct frequency from the computer is below 85Hz, try a
higher frequency (upper limit 85Hz). There may be a slight
attenuation of the current image.
• Try turning the Vertical Filter On. For this case however, the
vertical resolution will drop.
38
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor may
heat up. This is not a malfunction.
–
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images with
a vertical resolution greater than 512 lines are displayed;
however, this is not a malfunction.
–
• The screen becomes dark and the images cannnot be seen • This sometimes occurs when a component output VTR such as the
during VTR special playback (fast forward, rewind)
480i is connected.
This is not a malfunction; therefore, please take note that this may
occer. When it does occur, change to composite output,or S.video
output.
• During multi picture mode, sub pictures are not displayed.
• Sub pictures image might not be able to be displayed, depending
on the combination.
(Reter to the table of “2 picture mode” and “4 picture mode”)
ENGLISH
Symptoms That Seemingly Appear to be Failures (continued)
–
28
• The screen display sizes are not switched.
• The screen dicplay size is fixed at “Full” as receiving 1080i/60Hz,
1080i/50Hz, and 720p.
• Images from AV6 (HDMI) are not displayed.
• Check the cable and output format of connecting device.
(Reter to “Connecting to an Audio Visual Device”)
14
• Images from Photo Input are not displayed.
• Check the connecting device and image format.
(Reter to “Photo Input Display”)
30
–
31
32
51
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for RGB2)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1).
(RGB input).
Figure 1
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Example
1)
2)
3)
4)
Adjustment
procedure
Vertical
streaks
Press
Press
Press
Press
Before adjustment,
some characters
are blurred.
ABC
B
ABC
After adjustment,
all characters appear
crisp now.
ABC
ABC
After adjustment,
all characters are
blurred.
the MENU button. The Main Menu will be displayed.
the
SELECT button and select Setup.
the OK button. The Setup Menu will be displayed.
the
SELECT button and select Auto Adjust.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the
SELECT button and select Setup.
7) Press the OK button. The Setup Menu will be displayed.
8) Press the
SELECT button and select Horizontal Clock.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)
9) Press the
or
ADJUST buttons and search for clear characters over the entire screen.
10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (Figure 2).
A fine pattern flickers when displayed on the screen (Figure 3).
Figure 2
Before adjustment
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Figure 3
Before adjustment
ABC
ABC
Example
After adjustment
After adjustment
ABC
1)
2)
3)
4)
Adjustment
procedure
Press
Press
Press
Press
the MENU button. The Main Menu will be displayed.
the
SELECT button and select Setup.
the OK button. The Setup Menu will be displayed.
the
SELECT button and select Auto Adjust.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the
SELECT button and select Setup.
7) Press the OK button. The Setup Menu will be displayed.
8) Press the
SELECT button and select Clock Phase.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
9) Press
or
ADJUST buttons to make the text appear
clean across the screen.
52
9) Press
or
ADJUST buttons to make the text appear
without flickering.
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit and tuner unit have been inserted.
Display
dimensions
Resolution
Net dimensions
(excluding Speakers/Stand)
Net weight
(excluding Speakers/Stand)
Ambient
conditions
Approx. 32 inches (716 (H) x 399 (V) mm, Approx. 37 inches (814 (H) x 445 (V) mm, Approx. 42 inches (922 (H) x 522 (V) mm,
diagonal 820mm)
diagonal 930mm)
diagonal 1059mm)
852 (H) x 1024 (V) pixels
1024 (H) x 1024 (V) pixels
1024(H) x 1024 (V) pixels
850 (W) x 545 (H) x 110 (D) mm
959 (W) x 612 (H) x 118 (D) mm
1050 (W) x 676 (H) x 110 (D) mm
25.5kg
30.5kg
37.0kg
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
245W / <3W
320W / <3W
380W / <3W
Audio output
speaker 12W + 12W (6Ω)
speaker 12W + 12W (6Ω)
speaker 12W + 12W (6Ω),
ENGLISH
Panel
(RGB input)
Input terminals
RGB1
RGB1
RGB2
RGB2
DVI input terminal (DVI-D)
audio input terminal (3.5mm Stereo Mini Jack)
analog RGB input terminal (D-sub 15-pin)
audio input terminal (3.5mm Stereo Mini Jack)
Input signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
44 modes
56
57
(Video input)
Input terminals
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/ PB / PR / video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal
AV3: L/R audio input terminal (RCA)
AV4: composite video / L/R audio input terminal (RCA)
AV5=AV3
AV6=HDMI input terminal
Photo input terminal (37/42 only)
Input signals
AV1: PAL, SECAM, NTSC3.58, NTSC4.43
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC4.43, NTSC3.58
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC4.43, NTSC3.58,
AV4: PAL, SECAM, NTSC4.43, NTSC3.58,
AV5=AV3
AV6=HDMI input signal 55
Output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
OUTPUT (HEADPHONE): L/R audio monitor- output terminal (Mini-pin)
Recommended signal
23 modes
55
(RF input)
Input terminals
ANT : 75Ω Unbalanced
RF Video System
PAL B, G, H / I / D, K
SECAM B, G / D, K / K1
NTSC-M
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
• RF input : TV only
53
PRODUCT SPECIFICATIONS (continued)
Signal Input
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
1
R (PR/CR)
2
G or sync on green (Y)
3
B (PB/CB)
4
No connection
5
No connection
6
R.GND (PR/CR, GND)
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
7
G.GND (Y, GND)
Sync signal type
Priority
8
B.GND (PB/CB, GND)
H/V separate sync.
1
9
No connection
H/V composite sync.
2
10
GND
sync.on Green *
3
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
(
* Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is not
possible. In this case, use H/V separate sync, H/V composite sync.
) : With component input
S-input connector pin specifications
Pin
Input signal
1
2
3
4
Y
Y-GND
C
Frame
C-GND
GND
Photo-input connector pin specifications
Pin
Input signal
1
2
3
4
5V
DM
DP
GND
HDMI connector pin specifications
Pin
1
2
3
4
5
6
7
8
9
10
54
Input signal
TMDS Data2+
Pin
11
TMDS Data2 Shield
TMDS Data2TMDS Data 1+
12
13
14
TMDS Data1 Shield
TMDS Data1-
15
16
17
TMDS Data0+
TMDS Data0 Shield
TMDS Data0TMDS Clock+
18
19
Input signal
TMDS Clock Shield
TMDS ClockCEC
Reserved(N.C. on device)
SCL
SDA
DDC/CED Ground
+5V Power
Hot Plug Detect
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Recommended Signal List
Applicable video signals for input terminal (TV mode)
RCA/S-video
Terminal
S-video
DVI
HDMI
Component
PC
Remarks
D-sub
Signal
CVBS
AV1
STB
RGB
Component
Refer to Setup Menu
36
AV2
Refer to Setup Menu
36
AV3
Refer to Setup Menu
36
AV4
Refer to Setup Menu
36
AV5
Refer to Setup Menu
36
Refer to Setup Menu
37
Refer to Setup Menu
37
AV6
RGB1
RGB2
( : Available)
With Composite Input(AV1~AV5 input) and S-video Input (AV3, AV5 input).
Signal mode
No.
1
2
Signal Name
NTSC4.43
NTSC3.58
PAL
SECAM
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
59.94
15.73
—
50.00
15.63
—
Resolution
Vertical frequency
(Hz)
525
625
Remarks
With component input (AV1, AV2 and RGB2-component input).
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
50.00
15.63
—
480
59.94
15.73
—
576p
576
50.00
31.26
—
4
480p
480
59.94
31.47
—
5
1080i/50
1080
50.00
28.13
—
6
1080i/60
1080
60.00
33.75
—
7
720p/60
720
60.00
45.00
—
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
Remarks
Signal Name
Resolution
Vertical frequency
(Hz)
1
576i
576
2
480i
3
No.
Remarks
With HDMI input (AV6 input).
Signal mode
Signal Name
Resolution
Vertical frequency
(Hz)
1
VGA
640 x 480
59.94
31.47
25.18
EIA-861B
2
576i
720(1440) x 576
50.00
15.63
27.00
EIA-861B
3
480i
720(1440) x 480
59.94
15.73
27.00
EIA-861B
4
576p
720 x 576
50.00
31.25
27.00
EIA-861B
5
480p
720 x 480
59.94
31.47
27.00
EIA-861B
6
1080i/50
1920 x 1080
50.00
28.13
74.25
EIA-861B
7
1080i/60
1920 x 1080
60.00
33.75
74.25
EIA-861B
8
720p/60
1280 x 720
60.00
45.00
74.25
EIA-861B
No.
55
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List (continued)
With Digital signal input
Signal mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Signal Name
VGA
W-VGA
VESA
480p
576p
720p/60
1080i/60
1080i/50
Resolution
640 X 400
640 X 480
864 X 480
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
720 X 480
720 X 576
1280 X 720
1920 X 1080
1920 X 1080
Horizontal Dot clock Setup Menu Condition
Vertical frequency frequency frequency
DVI-PC
DVI-STB
(MHz)
(kHz)
(Hz)
70.08
59.94
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
59.94
50.00
60.00
60.00
50.00
31.47
31.47
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
31.47
31.25
45.00
33.75
28.13
25.18
25.18
34.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
27.00
27.00
74.25
74.25
74.25
Remarks
WVGA type : On
EIA-861B
EIA-861B
EIA-861B
EIA-861B
EIA-861B
( : acceptable)
56
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Recommended Signal List (continued)
With Analog signal input (RGB2 input)
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
70.08
31.47
25.18
640 X 480
59.94
31.47
25.18
No.
Signal Name
1
VGA
2
3
Resolution
Vertical frequency
(Hz)
640 X 400
Remarks
864 X 480
59.94
31.47
34.24
4
640 X 480
72.81
37.86
31.50
5
640 X 480
75.00
37.50
31.50
6
640 X 480
85.01
43.27
36.00
7
800 X 600
56.25
35.16
36.00
8
800 X 600
60.32
37.88
40.00
9
800 X 600
72.19
48.08
50.00
10
800 X 600
75.00
46.88
49.50
11
800 X 600
85.06
53.67
56.25
12
1024 X 768
60.00
48.36
65.00
1024 X 768
70.07
56.48
75.00
14
1024 X 768
75.03
60.02
78.75
15
1024 X 768
85.00
68.68
94.50
16
1152 X 864
75.00
67.50
108.00
17
1280 X 1024
60.02
63.98
108.00
18
1280 X 1024
75.03
79.98
135.00
19
1280 X 1024
85.02
91.15
157.50
20
1600 X 1200
60.00
75.00
162.00
21
1600 X 1200
75.00
93.75
202.50
22
1600 X 1200
85.00
106.25
229.50
23
640 X 480
66.67
35.00
30.24
24
832 X 624
74.55
49.72
57.28
25
1024 X 768
74.93
60.24
80.00
26
1152 X 870
75.06
68.68
100.00
27
1280 X 768
59.833
47.986
81.00
1280 X 768
69.997
56.137
94.760
1280 X 768
59.876
47.776
79.50
WXGA Mode : 1280x768
1366 X 768
60.015
47.712
85.50
WXGA Mode : 1366x768
13
28
W-VGA
VESA
Macintosh
W-XGA
29
30
W-XGA
WVGA type : On
• The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position, Vertical Position,
Horizontal Clock and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
57
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement