A2300SHR
GE Security
Installation/Operation Instructions
Warranty Information
A2300SHR
www.ifs.com
888-999-9IFS
A2300SHR
AUDIO MASTER
6
5
4
3
2
1
AUDIO REMOTE
6
5
4
3
2
1
Audio Out
Audio Out
4
3
2
1
Loop B Relay
Loop B Relay
Loop A Relay
Loop A Relay
FAULT
OUTPUTS
Audio In
Audio In
To next A2300SHR
series module
(Port A)
A2300SHR
AUDIO SELF HEALING RING
CARRIER
3
FAULT
ifs
CARRIER
2
LOOP A
A
AUDIO
REC
From previous
A2300SHR
series module
(Port B)
1
International
NC - 6
Fiber
NC - 5
Systems
NC - 4
Incorporated
Ground
Audio Out
Audio Out
GRD - 3
203.426.1180
AUDIO
XTMR
} Loop B Relay
} Loop A Relay
4
LOOP B
AUDIO
XTMR
2
www.ifs.com
AUDIO OUT
B
AUDIO
REC
1
Black wire
GRD - 2
POWER
+10-31 VDC - 1
Black with
white stripe
POWER
A2300SHR
AUDIO SELF HEALING RING
MASTER
CARRIER
4
LOOP B
AUDIO
XTMR
FAULT
LOOP A
A
AUDIO
REC
ifs
CARRIER
International
2
1
GRD - 6
Fiber
AUDIO IN
Systems
5
4
Incorporated
www.ifs.com
NC - 1
AUDIO
REC
GRD - 2
POWER
+10-31 VDC - 1
POWER
A2300SHR
AUDIO SELF HEALING RING
4
LOOP B
AUDIO
XTMR
AUDIO
REC
ifs
CARIIER
2
LOOP A
A
From previous
A2300SHR
series module
(Port A)
3
FAULT
1
International
NC - 5
Systems
NC - 4
Incorporated
GRD - 3
203.426.1180
AUDIO
XTMR
To next A2300SHR
series module
(Port B)
2
www.ifs.com
AUDIO OUT
B
AUDIO
REC
1
GRD - 2
POWER
POWER
} Loop B Relay
} Loop A Relay
NC - 6
Fiber
+10-31 VDC - 1
Ground
Audio In
Audio In
NC - 2
B
CARIIER
} Loop B Relay
} Loop A Relay
NC - 3
203.426.1180
AUDIO
XTMR
3
Ground
Audio Out
Audio Out
Black wire
Black with
white stripe
NOTE(S): The number of remote (repeater) modules is limited to 40.
Rela ys are CLOSED when carrier is being received and OPEN when light is lost.
Black wire
Black with
white stripe
A2300SHR
D
E
C
A
F
B
A
B
C
D
E
F
G
Carrier Detect Channel A
LED illuminates
Optical Transmitter Channel A
Optical Receiver Channel A
Carrier Detect Channel B
LED illuminates
Optical Transmitter Channel B
Optical Receiver Channel B
Power
LED illuminates
NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.
G
A2300SHR
A
B
C
1
2
1
2
3
4
5
6
1
2
3
4
A Power Connector
B Audio Connector
C Relay (Fault) Connector
PROPER MOUNTING METHOD
FOR THE A2300SHR
1) Locate unit on solid flat horizontal or vertical surface.
2) Position unit no closer than 24 inches from any power source or machinery.
3) Securely mount unit using (4) four mounting screws (not provided).
4) Attach power wires to terminal block, black wire to PIN 2 and black wire with
white stripe to PIN 1.
5) Plug power brick into approved 120v AC outlet.
6) Check power LED to insure device is properly powered, LED will illuminate green.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could
void the user’s authority to operate the equipment.
AUSTRALIA and NEW ZEALAND
GE Security
Unit 3
310 Ferntree Gully Road
Notting Hill, VIC 3168
Australia
Tel: +613 9239-1200
Sales: 1 300 361 479
[email protected]
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested for fire, shock and/or casualty
hazards as outlined in UL’s Standard(s) for Safety UL 60950-1, 1st edition/CSA C22.2 No. 60950-1-03,
1st edition. UL makes no representations, warranties or certifications whatsoever regarding the
performance or reliability of any security or signaling related functions of this product.”
Comprehensive Lifetime Warranty
(a) Seller warrants to the original End User that products and
any services furnished hereunder will be free from defects in
material and workmanship as of the date of delivery, and will
conform to Seller’s published technical specifications. The foregoing shall apply only to failures to meet said warranties which
appear within that period of time during which the Products are
installed in their original installation for the original End User
and operator of such Products; provided, however, that in the
event of product discontinuance, warranty support is limited to
five (5) years from the announcement of discontinuance.
Notwithstanding the preceding sentence, the duration of the
warranty period for products not manufactured by Seller (e.g.,
fiber optic cabling, test equipment, power supplies or batteries)
shall be the warranty period offered by the original
manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon
and Seller shall be notified of, and may be represented at, all
tests that may be made. The warranties and remedies set forth
herein are conditioned upon (a) proper storage, installation, use
and maintenance, and conformance with any applicable recommendations of Seller and (b) Buyer promptly notifying Seller of
any defects and, if required, promptly making the product
available for correction.
(c) If any product or service fails to meet the foregoing warranties, Seller shall thereupon correct any such failure either at
its option, (i) by repairing any defective or damaged product or
parts of the products, or (ii) by making available any necessary
repaired or replacement products or parts thereof. Any repaired
or replacement part or product shall be warranted for the
remaining period of the original Warranty Period. Seller shall
pay, or credit Buyer for, the cost of freight for all return
shipments of products or parts to Buyer. Where a failure
cannot be corrected by Seller's reasonable efforts, the parties
will negotiate an equitable adjustment in price.
GE
Security
re
he
si
n
(d) The preceding paragraph sets forth the exclusive remedies
for claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
all such liability shall terminate and BUYER shall have a reasonable time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the
warranty period. The foregoing warranties are exclusive and in
lieu of all other warranties, whether written, oral, implied or
statutory. NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL
APPLY. Seller does not warrant any products or services of others
which BUYER has designated.
Comp
www.IFS.com
Title 21
Code of Federal Regulations
Subchapter J
ty
ASIA PACIFIC
IFS/Crockett International Asia
Pacific Pte., Ltd.
3791 Jalan Bukit Merah
#09-15
e-Centre @ Redhill
Singapore 159471
Tel: +65 6235 2661
Fax: +65 6235 2369
Email: [email protected]
Complies with FDA
Performance Standard
for Laser Products
ran
LATIN AMERICA, MEXICO,
CENTRAL and SOUTH AMERICA
IFS/Crockett International
4407 Bee Caves Road
Suite 422
Austin, TX 78746
Tel: 512-477-8787
Fax: 512-477-8555
Email: [email protected]
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
ar
EUROPE, MIDDLE EAST,
and AFRICA
GE Security
Unit 7 Cliffe Park
Bruntcliffe Road
Morley, Leeds, UK
Tel: +44 113 238 1668
Fax: +44 113 253 8121
[email protected]
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
W
NORTH AMERICA
USA and CANADA
GE Security
IFS Fiber Optic Products
16 Commerce Road
Newtown, CT 06470
Tel: 203-426-1180
Fax: 203-426-3326
Email: [email protected]
ve
Lif
etime Pro
du
ct
As a company of innovation, GE Security reserves the right to change product specifications without notice.
For the latest product specifications visit GE Security online at www.GESecurity.com or contact your GE Sales Representative.
Copyright © 2007, GE Security Inc. All rights reserved.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement