FlashLogic DIR-CH8, FLRSCH10 Install Manual
FlashLogic FLRSCH10 is a versatile device that enhances your vehicle's functionality and security. It seamlessly integrates with your vehicle's electrical system, providing remote start capabilities, door lock/unlock, and more. With its compact size and user-friendly design, the FLRSCH10 is an ideal solution for those seeking convenience and peace of mind.
Advertisement
Advertisement
INSTALL GUIDE
DIR-CH(RS)-CH8-[FLRSCH10]-EN
DOCUMENT NUMBER
48370
REVISION DATE
20180321
FIRMWARE
DIR-CH(RS)-CH8-[FLRSCH10]
HARDWARE
FLRSCH10
ACCESSORIES
FLPROG (REQUIRED)
DIRECTED XL-202 RF-KIT & ADS-HRN(RS)-XL02 (OPTIONAL)
DIRECTED SMARTSTART & ADS-HRN(RS)-SM01 (OPTIONAL)
TERMS OF USE: Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by
Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
BEFORE INSTALLATION
1- Connect module to computer
2- Login to Weblink account
3- Flash firmware to module (module is not preloaded with firmware)
4- Use accessories accordingly (accessories are sold separately) www.flashlogic.com
NOTE
I WARNING: All vehicle doors must be closed and locked prior to remote start sequence.
Dart STD key (Tip-Start) AT
1500 / 2500 / 3500 STD key (Tip-Start) AT
1500 / 2500 / 3500 STD key (Tip-Start) AT
1500 / 2500 / 3500 Diesel STD key (Tip-Start) AT
1500 / 2500 / 3500 Diesel STD key (Tip-Start) AT
VEHICLE LIST - 1 OF 1
FEATURES
PAGE 2 OF 23
DOC.: #48370
• 20180321
13-16 1 • • • • • • • • • • •
13-17 2 • • • • • •
18 3 • • • • • •
14-17 2 • • • • • •
18 3 • • • • • •
•
•
•
•
•
•
•
•
•
•
•
•
•
• • • • •
• • • • •
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
BOX CONTENTS
MODULE
BLUE
2
4
6
1
3
5
BLACK
8
10
12
14
16
18
20
2
4
6 5
7
9
1
3
11
13
15
17
19
BLACK
2
4
6
8
10
12
1
3
5
7
9
11
A
B
C
LED 2
LED 1
G
F
E
PROGRAMMING
BUTTON
4
3
2
1
BLACK
RF PORT/
WEBLINK PORT
4
3
2
1
3
2
1
BLUE
TELEMATIC
PORT
BLACK
D 9
7
5
3
1 2
10
8
6
4
WHITE
BOX CONTENTS - 1 OF 1
VS3
VS4
VS6
VS5
VS7
VS8
PAGE 3 OF 23
DOC.: #48370
• 20180321
10 PIN CONNECTOR
12 PIN CONNECTOR
AFTERMARKET HOOD SWITCH AND CABLE
WARNING STICKER
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
MODULE
WEBLINK PORT
4 PIN BLACK CABLE
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
COMPUTER
USB PORT www.flashlogic.com
RF KIT (accessories sold separately)
ADS-HRN(RS)-XL02
MODULE
RF PORT
TELEMATIC KIT (accessories sold separately)
ADS-HRN(RS)-SM01
MODULE
TELEMATIC PORT
XL202 RF DECODER
COMPATIBLE ACCESSORIES - 1 OF 1
DIRECTED XL202 RF KIT
XL202 ANTENNA
DIRECTED SMARTSTART
(NC)
(NC)
(NC)
PAGE 4 OF 23
DOC.: #48370
• 20180321
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
MODULE
A
B
C
A
2
4
6
1
3
5
B
G
F
E
D
RF PORT/WEBLINK PORT
TELEMATIC PORT
PURPLE (NC)
2
4
6
8
10
12
14
16
18
20
11
13
15
17
19
5
7
9
1
3
15 BROWN
18 PURPLE
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
NOTE 1
(SEE NEXT PAGE)
C
2
4
6
8
10
12
1
3
5
7
9
11 11 GRAY/GREEN - HORN (-) OUTPUT
D
2
4
6
8
10
5
7
9
1
3
04 GRAY/WHITE - HOOD STATUS (-) INPUT
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
TYPE 1 - WIRING DIAGRAM - 1 OF 2
PTS
OPTIONAL
VS7
VS8
VS3
VS4
VS6
VS5
NC
NC
WITHOUT OEM HOOD SWITCH:
INSTALL AND CONNECT TO
AFTERMARKET HOOD SWITCH
AFTERMARKET HOOD SWITCH (-)
HORN (-)
OBDII
A
PAGE 5 OF 23
DOC.: #48370
• 20180321
IGNITION NODE
IGNITION CONNECTOR
IGNITION HARNESS
OBDII CONNECTOR
OBDII HARNESS
OBDII HOLDER
LIGHT SWITCH CONNECTOR
LIGHT SWITCH HARNESS
DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
TYPE 1 - WIRING DIAGRAM - 2 OF 2
NOTE 1
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
STEP 1:
-IDENTIFY THE PURPLE (PIN 18) AND BROWN (PIN 15) WIRES FROM THE 20
-CUT THE PURPLE WIRE.
-CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER.
PIN BLACK CONNECTOR OF THE T ‐ HARNESS.
STEP 2:
-CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE.
WARNING
FAILURE TO PROPERLY SOLDER
CAN RESULT IN
FAULTY CONNECTIONS AND
PRODUCT MALFUNCTION
STEP 3:
-INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 6 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
MODULE
A
B
C
A
2
4
6
1
3
5
B
G
F
E
D
RF PORT/WEBLINK PORT
TELEMATIC PORT
PURPLE (NC)
2
4
6
8
10
12
14
16
18
20
11
13
15
17
19
5
7
9
1
3
15 BROWN
18 PURPLE
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
NOTE 1
(SEE NEXT PAGE)
C
2
4
6
8
10
12
1
3
5
7
9
11
02 GRAY (NC)
11 GRAY/GREEN - HORN (-) OUTPUT
D
2
4
6
8
10
5
7
9
1
3
04 GRAY/WHITE - HOOD STATUS (-) INPUT
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
TYPE 2 - WIRING DIAGRAM - 1 OF 2
PTS
VS3
VS4
VS7
VS8
VS6
VS5
OPTIONAL
NC
NC
WITHOUT OEM HOOD SWITCH:
INSTALL AND CONNECT TO
AFTERMARKET HOOD SWITCH
AFTERMARKET HOOD SWITCH (-)
HORN (-)
OBDII
A
PAGE 7 OF 23
DOC.: #48370
• 20180321
IGNITION NODE
IGNITION CONNECTOR
IGNITION HARNESS
OBDII CONNECTOR
OBDII HARNESS
OBDII HOLDER
LIGHT SWITCH CONNECTOR
LIGHT SWITCH HARNESS
DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
TYPE 2 - WIRING DIAGRAM - 2 OF 2
NOTE 1
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
STEP 1:
-IDENTIFY THE PURPLE (PIN 18) AND BROWN (PIN 15) WIRES FROM THE 20
-CUT THE PURPLE WIRE.
-CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER.
PIN BLACK CONNECTOR OF THE T ‐ HARNESS.
STEP 2:
-CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE.
WARNING
FAILURE TO PROPERLY SOLDER
CAN RESULT IN
FAULTY CONNECTIONS AND
PRODUCT MALFUNCTION
STEP 3:
-INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 8 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
1500 / 2500 / 3500
STD key AT
1500 Diesel / 2500 Diesel /
3500 Diesel
STD key AT
18
18
WIRE DESCRIPTION
CanH
CanL
CanH
CanL
TYPE 3 - WIRE CHART - 1 OF 1
~
~
~
~
Gray
Gray
Gray
Gray
10 pin
10 pin
10 pin
10 pin
WIRE COL
02 Orange
01 Yellow
02 Orange
01 Yellow
MODULE LOC
(DATA) Trailer module, right of steering column
(DATA) Trailer module, right of steering column
(DATA) Trailer module, right of steering column
(DATA) Trailer module, right of steering column
PAGE 9 OF 23
DOC.: #48370
• 20180321
~
~
~
~
COMPONENT LOC
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
TYPE 3 - WIRING DIAGRAM - 1 OF 2
MODULE
A
B
C
A
2
4
6
1
3
5
B
G
F
E
D
RF PORT/WEBLINK PORT
TELEMATIC PORT
PURPLE (NC)
2
4
6
8
10
12
14
16
18
20
11
13
15
17
19
5
7
9
1
3
15 BROWN
18 PURPLE
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
NOTE 1
(SEE NEXT PAGE)
C
2
4
6
8
10
12
1
3
5
7
9
11
02 GRAY (NC)
11 GRAY/GREEN - HORN (-) OUTPUT
D
2
4
6
8
10
5
7
9
1
3
04 GRAY/WHITE - HOOD STATUS (-) INPUT
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
PTS
BROWN/RED
BROWN/YELLOW
VS6
VS5
OBDII
VS3
VS4
NC
NC
CUT THE BROWN/RED AND BROWN/YELLOW WIRES.
INSULATE THE OBDII SIDE OF THE CUT WIRES AND
CONNECT THE OTHER SIDE TO VEHICLE CANH AND CANL.
CANH - 02
CANL - 01
A
B
VS7
VS8
OPTIONAL
WITHOUT OEM HOOD SWITCH:
INSTALL AND CONNECT TO
AFTERMARKET HOOD SWITCH
AFTERMARKET HOOD SWITCH (-)
DIR-CH(RS)-CH8-[FLRSCH10]-EN
HORN (-)
PAGE 10 OF 23
DOC.: #48370
• 20180321
IGNITION NODE
IGNITION CONNECTOR
IGNITION HARNESS
OBDII CONNECTOR
OBDII HARNESS
OBDII HOLDER
GRAY
1
6
2
7
3
8
4
9
5
10
LIGHT SWITCH CONNECTOR
LIGHT SWITCH HARNESS www.flashlogic.com
TYPE 3 - WIRING DIAGRAM - 2 OF 2
NOTE 1
ONLY FOR
ADS-HRN(RS)-CHR10
VER1.20
STEP 1:
-IDENTIFY THE PURPLE (PIN 18) AND BROWN (PIN 15) WIRES FROM THE 20
-CUT THE PURPLE WIRE.
-CAREFULLY STRIP THE BROWN WIRE USING A WIRE STRIPPER.
PIN BLACK CONNECTOR OF THE T ‐ HARNESS.
STEP 2:
-CONNECT AND SOLDER THE PURPLE WIRE TO THE BROWN WIRE.
WARNING
FAILURE TO PROPERLY SOLDER
CAN RESULT IN
FAULTY CONNECTIONS AND
PRODUCT MALFUNCTION
STEP 3:
-INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 11 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
05
MODULE PROGRAMMING PROCEDURE - 1 OF 2
01
02
03
Close driver door. Re-open driver door to wake up data bus.
07
OFF
ACC ON
START
Remove key.
Press Unlock on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button.
08
OFF
ACC ON
START
Insert key into ignition.
Wait, LED will fl ash GREEN once [1x]. If LED does not fl ash GREEN, press Unlock on OEM remote again.
09
OFF
ACC ON
START
Turn key to ON position.
04
OFF
ACC ON
START
Turn key to ON position.
10
Wait, LED will fl ash GREEN.
Wait, LED will turn solid RED.
06
OFF
ACC ON
START
Turn key to OFF position.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
13
14
16
PAGE 12 OF 23
DOC.: #48370
• 20180321
Connect module to computer and proceed with extended programming.
WARNING: Do not press module programming button. Connect power fi rst. Connect module to vehicle.
15
OFF
ACC ON
START
Turn key to ON position.
Wait, LED will turn solid GREEN for 2 seconds.
11
OFF
ACC ON
START
Turn key to OFF position.
12
DIR-CH(RS)-CH8-[FLRSCH10]-EN
17
OFF
ACC ON
START
Turn key to OFF position.
WARNING: Disconnect power last. Disconnect module from vehicle.
18
OFF
ACC ON
START
Turn key to START position.
www.flashlogic.com
19
OFF
ACC ON
START
Turn key to OFF position.
20
Module Programming Procedure completed.
MODULE PROGRAMMING PROCEDURE - 2 OF 2 PAGE 13 OF 23
DOC.: #48370
• 20180321
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
>>
01
NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.
>>
Time restriction. Complete next step within 7 seconds.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
To exit valet mode: repeat steps 1 to 5.
02
OFF ACC
ENGINE
START
STOP
03
Cycle ignition ON fi ve times [5x OFF/ON] rapidly.
Wait, LED 1 will turn solid RED for 2 seconds.
04
05
ENGINE
START
STOP
ON START
Set ignition to OFF position.
Valet Mode Programming Procedure completed.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 14 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
AFTERMARKET REMOTE PROGRAMMING:
NOTES
I All aftermarket remotes must be programmed to the
RF-Kit.
Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 15 OF 23
DOC.: #48370
• 20180321
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
>>
>>
>>
It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the
Module Navigation will drain vehicle battery.
To exit the Module Navigation at any time:
Follow STEP 13.
Module must be programmed to the vehicle.
04
05
Use the Module Navigation Chart on the next page.
06
01
ON START
Set ignition to OFF position.
07
ENGINE
START
STOP
02
TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid
GREEN.
08
03
[X]
IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
09
MODULE NAVIGATION PROCEDURE - 1 OF 1
TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid
RED.
[Y]
IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously.
TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid
GREEN.
[Z]
LED 1 will flash GREEN as many times as the current (or default) setting number, continuously.
10
11
12
13
[Z]
IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously.
To return to the MENUS: exit the Module
Navigation and redo the Module Navigation
Procedure.
14
>>
DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 16 OF 23
DOC.: #48370
• 20180321
To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.
[Y]
LED 1 will fl ash RED as many times as the current option number continuously.
Configure every other setting and proceed to step 13.
MANDATORY: EXIT MODULE NAVIGATION.
Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF.
Module navigation completed.
Failure to exit the Module Navigation will drain vehicle battery.
www.flashlogic.com
MODULE NAVIGATION CHART - 1 OF 2
MODULE NAVIGATION CHART:
NOTES
I Default settings are listed in bold.
II Make sure the option is covered on the vehicle before attempting to change the setting.
*Vehicle will shutdown when a door is opened.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
01 CONFIGURATION
01 DISARM/UNLOCK BEFORE START
02 RELOCK AFTER START
03 RELOCK AFTER SHUTDOWN
04 FORCE UNLOCK ALL ON FIRST PRESS
05 TAKEOVER
06 N/A
07 N/A
08 MODULE RUN TIME
09 WAIT TO START DELAY
10 N/A
11 N/A
12 N/A
13 N/A
04 15 MIN
05 25 MIN
06 30 MIN
07 35 MIN
08 15 MIN
01 02 SEC
02 05 SEC
03 08 SEC
04 10 SEC
05 15 SEC
06 20 SEC
07 25 SEC
08 30 SEC
01 N/A
01 N/A
01 N/A
01 N/A
01 OFF
02 ON
01 OFF
02 ON
01 OFF
02 ON
01 OFF
02 ON
01 ENABLE
02 DISABLE*
01 N/A
01 N/A
01 03 MIN
02 05 MIN
03 10 MIN
DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 17 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
MODULE NAVIGATION CHART:
NOTES
MODULE NAVIGATION CHART - 2 OF 2 PAGE 18 OF 23
DOC.: #48370
• 20180321
01 CONFIGURATION
02-07 Technical Support only
14 HORN EVENT TRIGGER
15 HORN CHIRPS WIDTH
01 N/A
01 DOUBLE LOCK
02 LOCK + UNLOCK
03 LOCK + UNLOCK + START
04 DOUBLE LOCK + START
01 30 mSEC
02 15 mSec
03 60 mSec
01 N/A
*Vehicle will shutdown when a door is opened.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
REMOTE STARTER ERROR CODES - 1 OF 1
REMOTE STARTER ERROR CODES:
NOTES
I WARNING: The following applies only when the parking lights are connected and supported by the system.
II After a remote starter failure, the parking lights will fl ash
[X] number times to indicate an error code. See table.
14
15
16
10
11
12
13
06
07
08
09
03
[X] NUMBER OF PARKING LIGHT FLASHES
04
05
Foot brake is ON.
Hood is open.
Engine tach signal is lost.
System is in Valet Mode.
Vehicle is moving (VSS).
Glow plug timeout error.
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
N/A
N/A
N/A
N/A
N/A
N/A
CAN communication failure during RS sequence.
PAGE 19 OF 23
DOC.: #48370
• 20180321
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
MODULE DIAGNOSTICS - 1 OF 1
TEST MODULE
I DURING PROGRAMMING
II DURING REMOTE START
III WITH IGNITION OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Missing/wrong information from fi rmware or vehicle.
Module waiting for more vehicle information.
Additional steps required to complete module programming.
Module correctly programmed.
No activity or module already programmed.
Module incorrectly programmed.
Module incorrectly programmed.
Module correctly programmed and operational.
Reset in progress.
Invalid ground when running status from remote starter.
Module incorrectly programmed or connected.
Module not programmed. Waiting for more vehicle information.
False ground when running status from remote starter.
Reset in progress.
Module at rest and ready for a remote start sequence.
PAGE 20 OF 23
DOC.: #48370
• 20180321
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com
01
02
03
04
Disconnect all connectors from module except the BLACK 20-PIN connector.
07
MODULE RESET PROCEDURE - 1 OF 1
Reconnect all connectors.
Disconnect the BLACK 20-PIN connector.
08
Repeat programming procedure.
PRESS AND HOLD the module’s programming button while connecting the BLACK 20-PIN connector.
>>
Wait, LED 1 will flash RED. RELEASE programming button.
LED 1 will turn RED for 2 seconds.
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
05
06
Module RESET completed.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 21 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
>>
01
02
03
04
Close driver door.
05
OFF
ACC ON
START
Turn key to ON position.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018
All vehicle doors must be closed and locked prior to remote start sequence.
06
Time restriction. Complete steps 2 to 6 within
45 seconds.
07
Press unlock on OEM or aftermarket remote.
>>
Open driver door and enter vehicle.
TAKEOVER PROCEDURE - 1 OF 1
Press and release BRAKE pedal.
Take over procedure completed.
Failure to follow procedure will result in vehicle engine shutdown.
DIR-CH(RS)-CH8-[FLRSCH10]-EN
PAGE 22 OF 23
DOC.: #48370
• 20180321 www.flashlogic.com
¨
¨
8
¨
¨
6
¨
¨
7
5
¨
¨
¨
4
¨
¨
1
2
3
¨
INSTALLATION CHECKLIST - 1 OF 1 PAGE 23 OF 23
DOC.: #48370
• 20180321
CHECKLIST
WARNING: Vehicle engine will start many times. Test in a well ventilated area.
Close all vehicle doors, hood and trunk.
Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9
¨
¨
10
¨
¨
11
12
13
¨
¨
19
20
¨
¨
14
15
16
17
18
Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
Open hood.
If not already installed, affi x the mandatory orange warning sticker under the hood and proceed to next step.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
Close hood.
Enter vehicle and close the doors.
Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Wait for the vehicle to start.
Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once
[1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
Exit vehicle.
Installation checklist completed.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. © 2018 DIR-CH(RS)-CH8-[FLRSCH10]-EN www.flashlogic.com

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote start your vehicle for added convenience
- Lock and unlock doors remotely for enhanced security
- Compatible with a wide range of vehicles for versatility
- Easy to install and program for hassle-free setup
- Compact size for discreet integration within your vehicle