Sulzer ABS CA 523 Installation Manual

Add to my manuals
8 Pages

advertisement

Sulzer ABS CA 523 Installation Manual | Manualzz

GSM-3G Modem Type ABS CA 523

EN Installation Guide

www.sulzer.com

GSM-3G modem type ABS CA 523, Installation guide

Copyright © 2017 Sulzer. All rights reserved.

This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Sulzer. Sulzer assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Sulzer.

Sulzer reserves the right to alter specifications due to technical developments.

EN

2

GSM-3G modem type ABS CA 523, Installation guide

1

MOUNTING

1.1

Part number 28007005 contains:

1. Modem

2. Antenna

3. Power cable

4. DIN rail socket with 2 screws

1. The Modem 2. Antenna 3. Power cable 4. DIN rail socket with

1.2

Part number 28007006 contains:

Same items as part number 28007005 above with additional RS-232 cable which also can be ordered separately (p/n: 43320588). See accessory list on page 7 below.

5. cable

1.3

DIN-rail socket (no. 4)

If the modem is to be mounted on a DIN-rail; attach the DIN rail socket on the rear side of the modem. Use the two screws included to fasten the socket.

1.4

Antenna (no. 2)

Mount the antenna into the connector at the modem. Place the antenna in open environment and shielded from precipitation. The backside of the antenna has adhesive Sellotape or Scotch tape for mounting on a clean surface. Avoid mounting the antenna on a grounded metal plate; it short circuits the signal.

1.5

Power connection

Use the enclosed power cable (no. 3). Plug in the RJ6/8 connector to the power jack in the modem. Connect the open ends to your power supply according to description below. The modem is supplied with +10 ─ + 30 VDC.

6 5 4 3 2 1

Pin assignment and typical connection:

1 Blue

2 Black

3 Red

4 Green

5 Yellow

6 Brown

+10 ─ +30 V

0 V

EN

3

GSM-3G modem type ABS CA 523, Installation guide

1.6

Power Supply

1.7

Mounting of DIN-rail holder

The DIN-rail holder is fastened with two screws enclosed in the kit to fit an uni versal 35 mm DIN-rail according to DIN EN 60715. There are two alternatives of mounting the holder depending on if the modem shall be mounted horizontally or vertically.

Alternative 1

Alternative 2

Figure 1-1 Mounting the holder for DIN-rail

1.8

Antenna

The enclosed antenna is a Dipole type T and is to be mounted on a nonmetallic surface. For metal cabinet; use the “Smartdisc”-antenna. The Dipole-T and the

Smartdisc antenna cable must not be extended.

In the section of 4.1 Accessory List are additional antennas which can be ordered from Sulzer if the receiving signal is not sufficient.

EN

4

GSM-3G modem type ABS CA 523, Installation guide

2

RS-232 Communication and cable configurations

7

8

5

6

9

3

4

1

2

Use the communication cable (section 1.2 on page 3) to connect the substation.

Follow the table below to ensure communication. The default parameters for the modem are; 115200 baud, No parity, 8 data bits, 1 stop bit.

CA 523

D-Sub 9 (F)

D-Sub 9 (M)

Cable Color

Pink

Brown

White

Blue

Gray

-

Green

Yellow

-

Connections in Controllers

Signal PC 441 PC 242

RXD

TXD

RTS

GND

RTS

CTS

51

50

49

52

49

48

23

24

25

22

25

26

PCx

47

48

49

46

49

50

Antenna

5

EN

GSM-3G modem type ABS CA 523, Installation guide

3

Installing the SIM card

Green LED

(Power on/off)

Yellow LED

(Network status)

SIM inserted

The SIM - with the circuit side facing towards the Sulzer logo - is inserted by gently pushing it into the SIM card holder until it snaps hold. It is now protected from accidental removal. The SIM can be removed from the card holder by using a flat object such as a screwdriver to carefully press the inserted SIM until it snaps out again.

3.1

Status LEDs

• A green LED; Power ON

• A yellow LED blinking every 2nd second; Network search

• A yellow LED flashes every 4th second; Connected to 2G/3G network

3.2

About SIM cards

AquaWeb

Sulzer provides the AquaWeb SIM-cards. To connect your station to Aquaweb, follow the instructions enclosed with the SIM.

SIM card from other providers

Only telematics enabled SIM card is working. Consult your SIM provider of which functions has to be enabling on the subscription of SIM card.

EN

6

GSM-3G modem type ABS CA 523, Installation guide

4

Technical Data

Five band 3G UMTS (WCDMA/FDD)

Quad band GSM

Ambient operating temperature

Automatic thermal shutdown

Degree of protection

Housing material

Mounting

Humidity

Dimensions

Power supply

Power consumption

Altitude

Compliance

800, 850, 900, 1900 and 2100 MHz

850, 900, 1800 and 1900

–30 to +65 °C (–22 to +149 °F)

Min: <-40 °C, Max: >+90°C (± 3°C)

(Min. <-40 °F, Max: >194 °F)

IP 20, NEMA: Type 1

PPO and PC

With socket; DIN Rail 35 mm

0–90% RH non-condensing

H x W x D: 26 x 115 x 86 mm

(1.0 x 4.5 x 3.5 inch)

+10 – 30 VDC

< 5 W

Max 2000 MASL or 6562 ft. AMSL

R&TTE, GCF, FCC, PTCRB, IC, UL

Attention If the unit is used in a manner not described in this document the protection provided by the equipment may be impaired.

4.1

Accessory list

Part number

43320588

Description Note

Modem cable with DB9M + open end

This part is included in

28007006

Antenna Accessories

Part number

28007007

28007008

Description

Low profile Smartdisc

(SMA-M) +1 dB, 2.5 m

Align antenna kit +6.0 ─ +9.0 dBi

28007010 Adapter FME-M to SMA-M

Note

Extension of the cable is not recommended

Included in kit:

Antenna

10 m cable

2 m cable

Wall and mast mounting equipment

Only when CA 532 is connected to an old antenna

4.2

Cleaning

How to clean the unit

Powers off the unit and only outside/front shall be cleaned by using a dry, soft cloth. A good choice would be the microfiber type of cloth and gently wipe the

CA 523 unit on front in order not to scratch the overlay. If the dry cloth did not completely remove the dirt, do not press harder in an attempt to scrub it off. If necessary, moisten the cloth by adding a small amount of water with thin solution of mild detergent and try again. Never use detergent with polish or solvent which can have an impact of the plastic surface.

EN

7

Copyright © Sulzer Ltd 2017

Sulzer Pump Solutions Ireland Ltd., Clonard Road, Wexford, Ireland

Tel. +353 53 91 63 200, Fax +353 53 91 42 335, www.sulzer.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement