D-Link Express EtherNetwork DI-604 Quick Install Manual

Add to My manuals
16 Pages

advertisement

D-Link Express EtherNetwork DI-604 Quick Install Manual | Manualzz

This product can be set up using any current web browser, i.e., Internet Explorer

6x, Netscape Navigator 7x.

DI-604UP

Wired Router with USB Printer Port

Before You Begin

1. If you purchased this router to share your high-speed Internet connection with other computers, you must have either an Ethernet-based Cable or a DSL modem with an established Internet account from an Internet Service Provider (ISP).

2. It’s best to use the same computer that is connected to your modem for configuring the DI-604UP router. The DI-604UP Broadband Router acts as a

DHCP server and will assign all the necessary IP address information on your network. See Appendix at the end of this Quick Installation Guide or the

Manual on the CD-ROM for setting each network adapter to automatically obtain an IP address.

Check Your Package Contents

These are the items included with your DI-604UP purchase:

• DI-604UP Broadband Router

• CD-ROM

• Ethernet (CAT5 UTP/Straight-Through) Cable

• 5V DC, 2 A Power Adapter

Using a power

supply with a different voltage rating will damage and void the warranty for this product.

If any of the above items are missing, please contact your reseller.

©2007 D-Link Networks, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice.

Connecting The DI-604UP Broadband

Router To Your Network

A.

First, connect the power adapter to the receptor at the back panel of the DI-

604UP and then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation.

B.

Insert one end of an Ethernet cable to the WAN port on the back panel of the

DI-604UP and the other end to the Ethernet port located on your Cable or DSL modem. The WAN LED light will illuminate to indicate proper connection.

C. Insert one end of an Ethernet cable to LAN port 1 on the back panel of the DI-

604UP and the other end to an available Ethernet port on the network adapter in the computer you will use to configure the DI-604UP. The LED light for LAN Port 1 will illuminate to indicate proper connection. (Note: Some computers already have network adapters pre-installed.)

B. WAN Port

This is the connection for the

Ethernet Cable to

Ethernet Port on the

Cable or DSL

Modem.

Reset Button

Pressing this button restores the router to its original factory default settings.

USB Port

This is connection for your USB printer.

C .

LAN Ports

These are the connections for

Ethernet cables to your Ethernetenabled computers

Restart Your Computer

2

A .

Receptor for

Power Adapter

Connecting Additional Devices to the

DI-604UP Broadband Router

Using additional Ethernet (CAT5 UTP/Straight-Through) cables, connect your

Ethernet-equipped computer(s) to one of the 3 remaining Ethernet LAN ports on the back panel of the DI-604UP.

LAN Port LEDs.

Each of the LAN ports on the back of the DI-604UP have a corresponding LED light on the front panel of the unit. When a proper connection has been made to a computer that is ON, the LED on the front panel should illuminate.

USB Port LED.

The USB port on the back of the

DI-604UP has a corresponding LED light on the front panel of the unit.

When a proper connection has been made to a device that is ON, the LED on the front panel should illuminate.

Additional printer may be added to your DI-604UP to increase functionality. By connecting a printer to the USB port at the back of the router, you may share print capabilities over your wired network. A valid USB connection will cause the corresponding USB LED at the front to light. For more information regarding USB connections and device implementation, see the DI-604UP user guide.

3

When you have completed the steps in this Quick Installation Guide, your connected network should look similar to this:

Cable or DSL

Modem connected to the WAN port.

DI-604UP

Broadband Router

Printer connected to the USB port.

Computers connected to the LAN

Ports

4

Using The Setup Wizard

Open your Web browser and type

“http://192.168.0.1” into the URL address box.

Then press the Enter or

Return key.

The logon pop-up screen will appear.

Type “admin” for the username and leave the password field blank.

Click OK

Once you have logged in, the Home screen will appear.

5

Click Run Wizard

You will see the following screens.

Click Next

Step 1 - Set up your new password .

You have the option to establish a password.

Click Next

Step 2 Choose your time zone.

6

Click Next

The Setup Wizard (continued)

Select the type of Internet connection for your router.

Select one of these settings

Click Next

If you are unsure of which setting to select, please contact your Internet

Service Provider.

If you selected Dynamic IP Address , this screen will appear:

7

“Clone MAC Address” button to automatically copy the MAC address of the network adapter in your computer. You can also manually type in the

MAC address.

What is a MAC address?

Each network adapter has a discrete

Media Access Control (MAC) address. Note that some computers and peripherals may already include built-in network adapters.

Click Next

If your ISP requires a Static IP Address , and this option is selected, then this screen will appear:

Enter the IP address information originally provided to you by your

ISP . You will need to complete all the required fields.

Click Next

If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet) and this option is selected, then this screen will appear:

8

Enter in the username and password provided to you by your ISP and retype that same password to verify it.

Click Next

Please be sure to remove any existing PPPoE client software installed on your computers.

9

If your ISP uses PPTP and this option is selected, then this screen will appear.

Enter the IP address information originally provided to you by your

ISP .

Click Next

If your ISP uses L2PT and this option is selected, then this screen will appear.

Enter the IP address information originally provided to you by your

ISP .

Click Next

10

If your ISP is Big Pond Cable and this option is selected, then this screen will appear.

Enter in the username and password provided to you by your ISP and retype that same password to verify it.

Click Next

If your ISP supports Multiple PPPoE and this option is selected, then this window will appear.

Enter the username and password provided to you by your ISP and retype that same password to verify it.

Click Next .

11

Your Setup is Complete!

Click Restart

Click Continue

You will be returned to the

Home

tab.

12

Tes

t Your Internet Connection

Click Exit

Relaunch your

Web browser (i.e.,

Internet Explorer or Netscape

Navigator ), to link to your favorite

Web site to test your Internet connection.

For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web-management interface; or to the manual located on the CD-ROM.

13

APPENDIX

To connect to the network, make sure the network adapter in your computer is configured properly. Here’s how to configure the network adapter to obtain an IP address automatically for the

DI-604UP Broadband Router.

For Microsoft Windows XP:

Go to Start > right click on

My Network Places > select Properties > Double-click on the Network Connection associated with the Ethernet adapter (i.e.,

D-Link DFE-530TX+).

Click Internet Protocol (TCP/IP)

Click Properties

Select Obtain an IP address automatically

Click OK

Restart your computer

14

For Apple Macintosh OS X:

Go to the Apple Menu and Select System

Preferences .

Select Built-in

Ethernet in the Show pull-down menu

Select Using DHCP in the Configure pulldown menu

Click on

Apply Now

The IP address information, the Subnet Mask, the Router’s

IP address and the Ethernet adapter address will appear.

Click on

Network

15

Technical Support

D-Link’s website contains the latest user documentation and software updates for D-Link products.

Canadian customers can contact D-Link Technical Support through our website or by phone.

Tech Support for customers within Canada:

Telephone:

(800) 361-5265

Mon. to Fri. 9:00AM to 9:00PM

World Wide Web http://support.dlink.ca

Email [email protected]

Ver.1.00(CA)

2007/08/07

6I604UPQ..D1G

16

advertisement

Related manuals

Download PDF

advertisement