Delvcam
DELV-WFORM-7SDI
User Guide
IMPORTANT SAFETY INSTRUCTIONS:
Please read manual before using this product.
Please keep manual for future reference.
Please read the cautions to prevent possible danger and loss of property.
Please enjoy the benefits of convenience, safety, and space-saving from this
TFT LCD monitor in different ways.
FEATURES:
Metal housing;
Wide viewing angles;
Wide voltage: DC 7-24V;
High brightness: 400cd/ ㎡ ;
High contrast: 800:1;
TALLY interface with indicating light;
Faster response time;
Firm & portable design;
Long F1~F4 keep press to POP-UP shortcut menu.
CAUTIONS:
1. Please do not place the display screen towards the ground.
2. Please avoid heavy impact or drop onto the ground.
3. Please do NOT use chemical solutions to clean this product. Please wipe with a clean soft cloth to maintain the brightness of the surface.
4. Please do not block any vent hole.
5. Please follow the instructions and trouble-shootings to adjust the product.
Other improper adjustment may result in damage. Any further adjustment must be performed or conducted by a qualified technician.
6. Please unplug the power and remove the battery if long-term no-use, or thunder weather.
YP-01140217
* Advanced functions are only available for product model with"/P2"&"/S2".
.
1
Contents
PRODUCT DESCRIPTION
--------------------- 3
INSTALLATION OF SUNSHADE COVER
AND BATTERY PLATE
---------------------------5
DV BATTERY MOUNT PLATE
---------------- 6
WIRING INSTRUCTIONS
-----------------------7
SETTING MENU
---------------------------------- 8
ACCESSORIES
------------------------------------11
PARAMETER
--------------------------------------12
TROUBLESHOOTING
--------------------------12
* Advanced functions are only available for product model with"/P2"&"/S2"..
2
PRODUCT DESCRIPTION
1 ． TALLY (indicator light).
2 ． Earphone jack.
3 ． Power indicator light: ON/OFF (Light turns to red when power on).
4 ． VIDEO: Indicator lights up when signal switch to video state.
5 ． YPbPr: Indicator lights up when signal switch to YPbPr state.
6 ． HDMI: Indicator lights up when signal switch to HDMI state.
7 ． SDI: Indicator lights up when signal switch to SDI state (optional).
8 ． F1 、 F2 、 F3 、 F4:User-definable buttons.
Default functions: （ function customized to meet your needs ）
Button Items Options(Loop switch)
F1 Screen Marker OFF, 95%,93%,90%,88%,85%, 80%
F2 Check Field OFF, MONO, Red, Green and Blue
F4 Image Flip H / V / H&V
*F2 Waveform/Vector Y, Vector, R, G, B, Cb, Cr, OFF
*F4 Histogram Y, Color, RGB, OFF
9 ． Knob BRI/MENU: Press the knob to access the menu function, pressing the knob in the menu to return to the previous page or exit the menu.
Rotate knob to select an option.
Default as Brightness function.
* Advanced functions are only available for product model with"/P2"&"/S2"..
3
10 ． Knob SAT: Press the knob to select main MENU options; rotate knob to confirm the selection and adjust parameter values.
Default as Saturation function.
11 ． Knob TINT: Default as Tint function.
12 ． Knob CONT: Default as Contrast function.
1. Battery power on/off switch: “ ǁ ” is battery power; “O” is power off; “|” is
DC power.
2. Battery pinch slots.
3. SDI signal input / output interface (optional).
4. YPbPr signal input interface.
5. Audio signal input.
6. Audio (L/R) input.
7. HDMI (High Definition Multimedia Interface) signal input / output.
8. 4-pin XLR DC power input.
Pin number Signal
①
②
③
④
GND
Red Light
Green Light
+12V
* Advanced functions are only available for product model with"/P2"&"/S2".
.
4
INSTALLATION OF SUNSHADE COVER
AND BATTERY PLATE
Installation of sunshade cover:
① As shown, buckle the sunshade cover on the device.
② As shown, cover buttoned into the appropriate slot, and fastened in accordance with the order of the both sides.
③ As shown, bend sunshade panel to meet and paste with sunshade cover interlocking.
④ Installation completed.
* Advanced functions are only available for product model with"/P2"&"/S2".
.
5
DV BATTERY MOUNT PLATE:
Standard mounts process
Following three types of battery plates are suitable for this device, model F970,
QM91D, DU21 & LP-E6 (choose 2 out of 4).
MODEL: F-970 MODEL: QM91D MODEL: DU21 MODEL: LP-E6
DV Battery Mount Plate:
DV Battery Mount Plate Specification:
Model DU21 for battery of Panasonic DV:
NV-GS/PV-GS/DZ-MV/GS/H28/H258/H288GK series, comply with
Panasonic battery DU06/VBD140/SANYO DZhs301sw/Hitachi
DZ-HS303SW/BZ-BP14S/DZ3200/BP07W.
Model QM91D for battery of SONY DV:
DSCR1/F/S/MVCCD/E/HC15E/HC1E/AE1u/DCRTRV828/E/CCD-TRV116/
DCR-DVD/PS105K/300K/10P/1E series.
Model F970 for battery of SONY DV:
DCR-TRV series, DCR-TRV E series, VX2100E PD P series, GV-A700,
GV-D800 FD/CCD-SC/TR3/FX1E/HVR-AIC, HDR-FX1000E, HVR-Z1C,
HVR-V1C, FX7E F330.
Model LP-E6 for battery of Canon DSLR:
5D Mark II/EOS7D/EOS60D ;
* Advanced functions are only available for product model with"/P2"&"/S2".
.
6
V-mount battery plate (optional):
Please refer to GP-L130AB type battery specifications.
V-mount Battery Plate
Adaptor Panel
Anton Bauer mount battery plate (optional):
Please refer to
GP-L130B type battery specifications.
Anton Bauer Mount Battery Plate
Adaptor Panel
WIRING INSTRUCTIONS
Power & TALLY cable
1. XLR (M) connector: to connect the XLR connector on device.
2. DC Power adapter connector.
3. Red: for TALLY red light connector.
4. Green: for TALLY green light connector.
5. Black: for grounding.
6. XLR (F) connector: for the XLR adapter.
* Advanced functions are only available for product model with"/P2"&"/S2"..
7
SETTING MENU
Before setting the functions, please make sure the device is connected correctly.
When power on, press BRI/MENU knob on the device, function menus will pop-up on the screen. After confirm the option value, then press BRI/MENU knob to return to the previous, and press the BRI/MENU knob again to exit the menu settings.
BRI / MENU knob: to select an option.
SAT knob to select the main menu, adjusting option values and confirm the selection.
ITEMS OPTIONS
Color Temp 6500ºK/7500 ºK/9300 ºK/User
R Gain 0-255
G Gain
B Gain
0-255
0-255
R Offset
G Offset
B Offset
0-511
0-511
0-511
Note: Only available under “User” mode to meet the color value you need.
Check Field OFF,MONO, Red, Green and Blue
Aspect Ratio Full Screen, 4:3 and 16:9
Pixel-to-Pixel ON/OFF
(5DII Mode)
/ 1080I
(5DIII Mode)
H/V delay OFF, H&V Delay, V Delay and H Delay
Underscan ON/OFF
* Advanced functions are only available for product model with"/P2"&"/S2"..
8
ITEMS OPTIONS
Center Marker ON/OFF
Aspect Marker OFF, 16:9, 4:3, 14:9, 13:9,15:9,1.85:1, 2.35:1
Screen Markers OFF, 95%,93%,90%,88%,85%, 80%
Marker Color
Marker Mat
Red, Green, Blue, White, Black
OFF, 1-6
Thickness 1-7
ITEMS OPTIONS
PIP Small, Medium, Large, PBP, POP
In small, medium and large interface can adjust the source, position, and swap;
In PBP and POP interface can adjust the source and swap.
Input Format OSD 5s, 10s, 15s
Freeze Input
Image Flip
*Wave/Vector
* Waveform Trans
ON/ OFF
H / V / H&V
Y / Vector / R / G / B / Cb / Cr / OFF
ON/ OFF
* Waveform Size
* Level Meter
Small / Large
Manual/Auto
Manufacturer Default OK/Cancel(Reverse the SAT / ADJ knob to select "OK") accidentally!)
* Advanced functions are only available for product model with"/P2"&"/S2"..
9
Function of buttons and knobs can be customized by users’ needs.
Functions of F1-F4 buttons can also be customized: Center Marker, Screen
Marker, Check Field, Color Bar, Camera, PIP, Image Flip, Zoom, Pixel-to-Pixel,
Freeze Input, Underscan, H/V delay
* Peaking, False Color, Exposure, Histogram, Level Meter and Wave/Vector.
Functions of R1-R4 buttons can also be customized: Contrast, Brightness,
Saturation, Tint, Volume, Sharpness and Back Light.
F1-F4 or R1-R4 shortcut key steps:
1. Press BRI/MENU knob to pop up the menu;
2. Rotating SAT knob, select the option;
3. Rotating BRI / MENU knob, select option needs to set for the F1-F4 or
R1 - R4;
4. Right rotating the SAT knob to the next menu options;
5. Rotating BRI / MENU knob to select the option to be set, then turn the
SAT knob right to confirm the option as default;
6. Finally, press the BRI / MENU knob to exit the menu.
Long keep press any F1-F4 button to pop-up shortcut menu when screen without a menu. As follows (item selected default as blue font):
Option can be selected by rotating BRI / MENU knob.
Finally, right turn the SAT knob to set the option as default.
* Advanced functions are only available for product model with"/P2"&"/S2"..
10
ACCESSORIES:
Standard Accessories:
1. Sun Shade Cover
2. Gimbal bracket
3. Battery Plate (F-970/QM91D/DU21/LP-E6)
4. HDMI A/C cable
5. Power & TALLY cable
6. Shoe Mount (for camera only)
7. 12V DC adapter
8. Suitcase
9. Adaptor Panel
10. Manual
Optional Accessories
1 Piece
1 Piece
2 Pieces
(Choose 2 out of 4)
1 Piece
1 Piece
1 Piece
1 Piece
1 Piece
1 Piece
1 Copy
1. Anton Bauer Mount Battery Plate
2. V-mount Battery Plate
3. Li-ion Battery
* Advanced functions are only available for product model with"/P2"&"/S2".
.
1Piece
1Piece
1Piece
11
PARAMETERS:
Panel Size 7’’ LED backlit
Resolution 1280×800
Brightness 400cd/ ㎡
Contrast 800:1
Viewing Angle 178°/ 178°(H/V)
Input Voltage
Input Signal
DC12V (XLR DC Connection)
HDMI
,
YPbPr
,
AV and 3G-SDI (optional) ,
Current 900mA
Power Consumption ≤ 11W
Size:(LWD) 191.5×152×31mm/141mm (with cover)
Weight 760g / 938g (with cover) / 2160g (with suitcase)
TROUBLE SHOOTING
1. Only black-and-white display:
Check whether the color saturation is properly setup.
2. Power on but no pictures:
Check whether the cables of Video, HDMI, YPbPr and SDI are correctly connected. Please use the standard power adapter coming with the product package. Improper power input may cause the device.
3. Wrong or abnormal colors:
Check whether the cables are correctly and properly connected. Broken or loose pins of the cables may cause a bad connection.
4. When on the picture shows size error:
Press “BRI/MENU → → Underscan” to zoom in/out pictures automatically
When receiving HDMI signals.
5. Other problems:
Please press “BRI/MENU” button and choose “
→ OK”
→ Manufacturer Default
6. According to the ISP, the machine can not function properly:
ISP for program upgrades, non-professionals do not use. Please reboot your computer if press accidentally!
* It is normal to see some bright lines appear on the screen when turn off the device.
Note: due to constant effort to improve products and product features, specifications may change without notice.
* Advanced functions are only available for product model with"/P2"&"/S2".
.
12
* Advanced functions are only available for product model with"/P2"&"/S2"..
13
