User Manual PDF
 en
se
=
cr
EXO
in
6. The engine exhaust from this product
> contains chemicals known. to the
State of California to cause cancer, birth
defects or other reproductive ‘harm.
YAMAHA LIT-CALIF 65-01
0
=
>
bei
A Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is
sold. ze
Fa
PE
Е
о = INTRODUCTION
1 L E
©. ©, EAL
Congratulations on your púrchase of the Yamaha YW125F. This model is the result of Yamaha” 5 wast experience in the pro-
duction of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reli-
ability that have made Yamaha a leader in these fields. 4
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you have
any questions conceming the operation or maintenance of your scooter, please consult a Yamaha dealer. % =
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at the
date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
scooter. To maintain these high standards, it 1, important that you and your Yamaha dealer pay close attention to he rec-
ommended Maintenance schedules and operating | instructions contained within this manual. %
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cut
rent product information available at the time of printing, there may be minor dec between your scooter and this
manual. If there is any Question concerning this manual, please consult a Yamaha dealer.
Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS" booklet “Carefully and completely
before operating this scooter. Do not attempt to operate this scooter until you have attained adequate knowledge
of its controls and operating features and until you have been trained in safe and proper riding techniques. Regular
inspections and careful maintenance, ‘along with good riding skills, will ensure that you safely enjoy the capabilities
and reliability of this scooter. LY Ч
EA
[= E:
Fa CA Fe
Le = e
IMPORTANT MANUAL INFORMATION
+, ©, EAL 1M
E
=
+ =
Particularly important information is disting uished in this manual by the following notations: %,
This is the safety alert symbol. It is used to alert you to potential personal injury.
A hazards. Obey all safety messages that follow this symbol to avoid possible i injury 7
or death. Es
A WARNING indicates a Fazardous situation which, if not avoided, could result in
a LE death or serious injury. —
6 | ua я “4 A NOTICE indicates special precautions that must be taken teo damage to the
y й vehicle or other property. © >
TIP A TIP provides key information to make procedures easier or clearer. %
“Product and specifications are subjectto change without notice. 6
Ts, = “a,
ях, Y
É i
%,
= 4 ea
4 o E &
By 6 i “Ч 7. 2,
} ' hs ь ый 2,
Te, E
%, “Е
"Чу By
Г. nd ps =
Fa e a Le]
3 Be i :
É IMPORTANT MANUALINFORMATION
ME —————]]]]——l[—]————;—[—————]——————]————]]]——— a E
E 4
бы. а
Ba Ч
Ge ci,
"47
"Ч РР
aE 5
> ip,
o y + -
E "|
€ a
"o 5,
A A
К. E
у a “+
“i Pe
; ve 4 Er
© % a
e 1 [| у
À Es
Bey ta
E A E Fa
"Я
К E
ca
a a da i's
AE AH
| EAUTITEZ fa
Ta
у —
fs Fo
3 VW125F EN
Li OWNER'S MANUAL x.
©2014 by Yamaha Motor Corporation, U.S.A. “e
“+ ist edition, July 2014 ">.
“5, Alt rights reserved. æ
Any réprinting or unauthorized use 5
without the written permission of “2
Yamaha Mator Corporation, U.S.A. = “6
is expressly prohibited. Ls "к
Printedin Taiwan. F =
эк |
P/N LIT-11626-28-32
>», i, > fo:
"ТА BLE OF CONTE NTS CR 2
LOCATION OF IMPORTANT FOR YOUR SAFETY -PRE-OPERATION Valve clearance ............................. 6-16
LABELS:.............ennnn 110 CHECKS Loomis 4-1 TIFES e meene nene nena nen 6-17
LC % — Castwheels.........—..————. 6-18
SAFETY INFORMATION muscu 1-3 OPERATION AND IMPORTANT RIDING © Checking the front brake lever free
Further safe-rding points................. 1-7 POINTS oii Bal e DIN ssi viet vids sanini ivan 6-19
A Starting the engine ........... 5-1 Adjusting the rear brake lever free
DESCRIPTION ......... 29... mece 2-1 Badingoff aman. 5-2 EEE a 6-19
Left View is pate A Acceleration and deceleration......... 5-2 Checking the front brake pads and
Right view. ec — RRM en a 5-3 rear bráke shoes... 6-20
Controls and inetruments... a pr 2-3 Tips for reducing fuel Checking théxbrake fluid level........ 6-21
1 “e CONSUMPION ...-... ea. irnos 5-3 Changing the brake fluid ............... 6-22
ÉS k INSTRUMENT AND CONTROL 5, Engine break-In.......... ip... 5-3 Checking and lubricating the
“EUNCTIONS..... - 3-1 FOI roo a een 5-4 CS Len. „6-22
«Main switch/steering A 3-1 so, Checking and lubricating the throttle
Keyhole cover.. … 3-2 PERIODIC MAINTENANCE AND grip and cable... . 6-23
Indicator lights and warning lig tis 3-2 ADJUSTMENT.................... e... ; 56-1 Lubricating the front and rear brake
Speedómeter UFIIE a 3-3 Owner's tool kit................—.—.. e... 6:2 lévers i sa SE 6-23
Fuel gauge. PSE EEE PRE RES PE 3-3 Periodic maintenance chart for the L Checking and lubricating the
Handlebar sWitches ........................ 3-4 emission control system ‚....сссоенеея 6-4 “. centerstand and sidestand ......... 6-23
Front brake levée... 3-5 General maintenance and lubrication “Checking the front fork... ... 6-24
Rear brake lever.’ Di nas 3-5 CELL cam ae esa 6-5 Cheeking the steering ..........———... 6-25
Fuel tank eap...........5 bei npeane 3-5 Removing and installing panels ...... 6-9 Checking the wheel bearings......... 6-25
ElÓ En pra aa” BL rs 3-6 Checking the spark plug................ 6-10 Battery .26. mn... eones 6-25
Catalytic converter............ bee ep 3-7 Engine oil... 6-11 Replacing the FUSES Lucscrrarscneneanennes 6-27
s Sea ieee ieee an SB Final transmission oik.........—.—ww—.. 6-13 Replacing a headlight bulb coves 6-27
2 Helmet holder = Ч. 3-9 Air filter and V-belt case Al filter Tail/brake light бо... … 6-28
_ Storage compartment...................- 2-9 SIOMIBNTE .....=......i..ecees ace borres 6-14 Replacing a tum signal light bulb... 6-28
tu SIdestand............. e. re recio 3-10 Checking the engine idling > Troubleshoting .........————.. e ——.... 6-29
Ignition circuit cut-off system ......... 3-11 speed... не Hg. . 6-16 Troubleshooting chart .................... 6-30
6, Esa the throttle grip free ee
CN play … in … 6-16
5, *
E он, we ay TE
< = > E
15 Ч. € “ta
À “a, E Ч
KA “+ — TABLE OF CONTENTS
SCOOTER CARE AND STORAGE ... 7-1 “8
Matte color gaution .... cnn TA =
Care... Been na nomas enn ena ens 7 “a,
DÉOTAGE inline
SPECIFICATIONS... %s, SESENTA 8-1 a
“CE Ч
CONSUMER INFORMATION. a 9-1 A 1
Identification numbers sn Mun 9-1 Be
Reporting safety defects............. “he 9-3 “e
“a, Motorcycle noise regulation............. “39-4 e. A
“Maintenance record... . 95. +, By
AHA MOTOR CORPORATION, % KY 2
.8,A. 2015 AND LATER MODEL с
SCOQTER LIMITED ®,
WARRANTY ... .. 9-7 %
YAMAHA EXTENDED SERVICE “a
(PES) Meana 9-9 %
oN
oF
Ea
A Ce
Ш" wr
ey oy
EV fu
5 5
> Bp
e ha
(a) uu
Lo ;
E, TE
A F-
E E
La Rs
- = e a С O
= “5 “ta -
a A fi o.
у ci, = cie
PA я “ih '
CM %,
a a
a. es ©
a, Les
A}
cru и
% E
Ч :
Е Ë a
(fi y
Ee "
gr
wo
ne
la we
ok. x=
13
Lr
ЧЕ +
cs
-
“ LOCATION OF IMPORTANT LABELS © "
Le a i
©, эй EAU HS
FM К: Я
Le ЛЕЙ
A “a,
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of
your vehicle. Never remove any labels from your vehicle. if a label becomes difficult to read or comes off, a replacement label
is available from your Yamaha dealer. 7 7
+ me
o
ga
PU
a
&
%
[ori] ка
Чаи ся
Te E =
Ч | $ >,
F a
7 2
E,
ke x,
E
“Ea
=
F ь
“и
"Ч
a
a
д,
ÉF
€
a, a 4
E ыы
a, =
'
E
A
Ч
©
E
Ч
Te.
E,
+ Cr
if
Cold ira normal pros me sha pe mat as
Го Пол.
5 Up io 30k {138bs) ¡nad
FRONT : 175kpa, 41 Рокот" уз,
HEAR :200kpa, [2.00ghom’ | 250s] '
= Blkg (1880s) ~~ manrmum load]
FRONT : 200kpa, [2 00Aglon”| 29ps
HEAR
LOAD LIMIT
’ ВКО! 11165}
> LTT
“a
en
a
Cr
1)
A WARNING |
NEVER sit here |
BL FRONT
Ta,
A
ЧЁ N
The
ry
aM
“E
сабкра, [2.250 от”) 3305
№ —— LOCATION OF IMPORTANT LABELS
4
| A WARNING
improper loading can cause loss of control.
Read owner's manual for proper loading
EH FR 5 ÉL:
E
E
ot =
т e
"я
A WARNING 3
* BEFORE YOU OPERATE THIS VEHICLE, READ
THE OWNER'S MANUAL ANDSALL LABELS.
= ALWAYS WEAR AN APPROVED ‘MOTORCYCLE
HELMET, eye protection, and pritective clothing.
=
==
7
FF ERE 00
EA
2
FE.
Le
A SAFETY INFORMATION ko
т
Ca * Esl 68
Be a Respolajbie Owner
As the vehicle's ‘owner, you are respon-
sible for the safe and. proper operation
of vour Scooter. a
Scooters are single- track’ vehicles.
Their safe use and operation are de-
pendent upon the use of proper riding
- techniques as well as the expertise of
“the operator. Every operator shoûld
know the following requirements before’.
riding:this scooter.
He or she should:
. Obtaifi-thorough instructions from
a competent source on all aspects
of scooter operation.
Observe the wamings and mainte-
nance requirements in this Own-
er's Manual. E
Obtain qualified training in safe
and proper riding techniques.
Obtain professional technical. ser-
vice as indicated in this Owners
- Manual and/or when made neces:: т
“sary by mechanical conditions.
% Neyer operate a scooter without
proper training or instruction. Take
a raifiigg course. Beginners
should receive training from a céf-
tified instructor. Contact an autho- +,
nzed scooter dealer to find out
about the training courses nearest
vou.
Safe Riding
Perform the pre-operation checks each
time you use the vehicle to make sure it
is in safe operating condition. Failure to
inspect or maintain the vehicle properly
“increases the possibility of an docident
or equipment damage. See page A-1
for a list of pre-operation checks. 6
® This scooter is designed to carry" E
the operator and a passenger.
* The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of auto-
mobile/scooter accidents, Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself con-
spicuous appears to be very effec-
tive in reducing the chance, of this
type of accident. EN
Therefore: En
* Wear a brightly colored jacket. °
+ Use extra caution when you are
1-3
5
approaching and passing
through intersections, since in-
tersections are the most likely
“E places for scooter accidents to
Bccur.
. Ride where other motorists can
See you. Avoid riding in another
motorist's blind spot.
» Never maintain a scooter with-
out proper knowledge. Contact
an authorized stooter dealer to
inform you on basic scooter
maintenance. Certain mainte-
nance can only be carried out by
certified staff.
“2 Many accidents involve inexperi-
“ enced operators. In fact, many op-
efators who have been involved in
accidents do not even have a cur-
rent driver's license.
+ Make sure that you are qualified
and that you only lend your
scooter to other qualified opera-
tors. Lo
« Know your skills} and limits.
Staying within your limits may
help you to avoid an accident.
* We recommend that you prac-
tice riding your scooter where
= io
So
7 SAFETY INFORMATION
there is ho traffic until you have
become thoroughly familiar with
the scooter and al of its con-
trols.
e Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to:ex-
cessive speed or undercornering,
“finsufficient lean angle for the *
speed).
= Always obey the speed limit and
never travel faster than warrant-
ed by road and traffic conditions.
* Always signal before tuming or
changing lanes. Make sure that
other motorists éan see you.
® The posture of the operator and
passenger is importen An proper
control.
* The operator should kee ‘Both
hands on the handlebar arid
_ both feet on the operator foot-“
“rests during operation to main-
tain control of the scooter.
. The “passenger should always
hold orto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
a
feet on the passenger footrests.
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
* Never ride under the influence of
alcohol or other drugs.
* This scooter is designed for
on-road use only. It is not suitable
for off-road use.
“Protective Apparel 5
The’ majority of fatalities from scooter
accidents are the result of head inju-
ries. The use of a safety helmet is the
single most critical factor in the preven-
tion or reduction of head injuries.
® Always wear an approved helmet,
® Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
;, * The use of a jacket, substantial
‘%, shoes, trousers, gloves, etc.. is ef-
“Mective in preventing or reducing
abrasions or lacerations. 2
® Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
1-4
% injury or an accident.
. “Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust sys-
tem become very hot during or af-
ter ope ration. and can cause bums.
e A passenger should also observe
the above precautions.
Avoid Carbon Monoxidé Poisoning
All engine exhaust contains. carbon
monoxide, a deadly gas. Breathing car-
bon monoxide can cause headaches,
dizziness, drowsiness, nausea, confu-
sion; and eventually death.
Carbon, Monoxide is a colorless, odor-
less, tasteless gas which may be pres-
ent even if you do not see or smell any
engine exhaust. Deadly levels of car-
bon monoxide can, collect rapidly and
you can quickly be overcome and un-
able to save yourself. Also, deadly lev-
els of carbon monoxide ean linger for
hours or days in enclosed“or poorly
ventilated areas. If you experience any
, symptoms of carbon monoxide poison-
“ing, leave the area immediately, get
fresh air, and SEEK MEDICAL TREAT-
MENT,
te
nl =
5
A SAFETY INFORMATION >.
E ; IF
LI
а
e Do not run engine indoors. Even if
you try to ventilate engine exhaust
= with fans or open windows and
EN doors, carbon monoxide can rap-
_ idly reach dangerous levels.
- Do not run engine in poorly venti-
lated or partially enclosed areas
such as bams, garages, or car-
ports:
® Do not tun engine outdoors where
engine exhaust can be drawn into
a building through openings such
as windows and doors.
Loading
+ Adding accessories or cargo to your
scooter can adversely affect stability
“and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
cautionwhen adding cargo or accesso-
ries to your scooter. Use extra care
when ridingéa scooter that has added
cargo or accessories. Here, along with
the information about accessories be-
low, are some general guidelines to fol-
low if loading cargo to your scooter:
The total weight of the operator, pas-
> senger, accessories and cargo must
not exceed the, maximum load limit.
Operation of an overloaded vehicle
could cause an accident.
Maximum load: E
155 kg (342 Ib) a
—
When loading within this weight limit,
keep the following in mind:
e Cargo and accessory weight:
“should be kept as low and close to
the scooter as possible. Securely
pack your heaviest items as close
to the center of the vehicle as pos-
sible and make sure to distribute
the weight as;evenly as possible
on both sides of the scooter to min-
imize imbalance orinstability.
® Shifting weights can create a sud-
den imbalance. Make sure that ac-
cessories and cargo are sécurely
attached to the scooter beforé‘rid-
ing. Check accessory mounts and.
“gargo restraints frequently.
+ ‘Properly adjust the suspension
for: your load (suspension-ad-
justable models only), and
check the condition and pres-
sure of you tires.
"En
15%,
* Never attach any large or heavy
items to the handlebar, front
fork, or front fender. Such items
can create unstable handling or
a slow steering response.
* This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
Genuine Yamaha Accessories.
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are avail- >,
able only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and acces-
sories or offer other modifications for
Yamaha vehicles. Yamaha is not in a
position to test the products that these
aftermarket companies produce.
+. Therefore, Yamaha can neither en-
dorse nor recommend the use of. ac-
cessories not sold by ‘Yamaha “ar
modifications not specifically recom=".
mended by Yamaha, even if sold and
installed by a Yamaha dealer.
a.
Cy
Lt
{i
I
Со
=
CL
=r
x
il
+
Bg
r ==
Pas
aD SAFETY INFORMATION
Aftermarket Parts, Accessories,
and Modifications
While you may find eat Prod-
ucts similar in design and quality to.
genuine Yamaha accessories, recog- TE
nize that some aftermarket accessories
or modifications are not suitable be-
cause of potential safety hazards to you
or others. Installing aftermarket prod-
ucts or having other modifications per-
formed to your vehicle that change any
of the vehicle's design or operation
characteristics can put you, and others
at greater risk of serious injury, or death.
You are responsible for injuries felated
to changes in the vehicle. Y
Keep the following guidelines in miña,
as well as those provided under “Load +
ing" when mounting accessories.
* Never install accessories or carry
cargo that would impair the perfor-
mance of your scooter. Carefully
inspect the accessory before using
it to make sure that it does not in
any way reduce ground clearance
or cornering clearafice, limit sus-
pension travel, steering, travel or
control operation, or obscúre lights
or reflectors. de
* Accessories fitted to the handle-
bar or the front fork area can
create instability due to improper
weight distribution or aerody-
namic changes. If accessories
are added to the handlebar or
“front fork area, they must be as
“lightweight as possible and
should be kept to a minimum,
« Bulkÿ;or large accessories may
seriously. affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to lift
the scooter, or the scooter may
become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
e
y 2» Certain accessories can dis-
“place the operator from his or
her normal riding position. This
improper position limits the free-
dom ofrmovement of the opera-
tor and may limit control ability,
therefore, such accessories are
not recommended,
® Use caution when adding electn-
cal accessories. If electrical acces-
1-6
sories exéeed the capacity of the
scooters efectrical system, an
electric failure ‘could result, which
could cause a dangerous loss of
lights or engine power.
Aftermarket Tires and Rims “-
The tires and rims that came with our
scooter were designed to match the
peftormance capabilities and to provide ®s,
the best combination of handling, brak-
ing, and’gomfort. Other tires, rims, siz-
es, and combinations may not be
appropriate. Refer to page 6-17 for tire
specifications and. more information on
replacing your tires.
С ha
Transporting the Scooter
Be sure to observe following instruc-
tions before transporting the scooter in
another vehicle, >
® Remove all loose items from the
© Scooter.
° “Point the front wheel straight
ahéad on the trailer or in the truck
bed, änd choke it in a rail to pre-
vent movement.
e Secure the ecooter with tie-downs
or suitable tn that are attached
YE
ry
“a
1
de
E
=
Le,
A SAFETY INFORMATION
F,
À
to solid parts of the acheter, Such
as the frame or upper frontfork tri-
ple clamp (and not, for example, to
rubber-mounted
break). Choose the location for the
straps carefully so the straps will
not rub against painted surfaces
during transport.
The suspension should be com-
pressed somewhat by the
tie-downs, if possible, so that the
scooter will not bourice excessive-
ly during transport.
handlebars er
turn signals, or parts that could”
fur
Este PEU
Further safe-riding points
e
He
"..
(ar
“because the scooter could slide.
a
Be sure to signal clearly when
making tums.
Braking can be extremely difficult
on a wet road. Avoid hard braking,
Apply the brakes slowly when
stopping on a wet surface.
Slow down as you approach a cor-
ner or turn, Once you have com-
pleted a turn, accelerate slowly.
Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers be-
come extremely slippery when
wet. Slow down and cross them
“with caution. Keep the scooter up-
right, otherwise it could slide out
from tinder you.
The brake pads or linings could get
wet when You wash the scooter.
After washing the scooter, check
the brakes before riding.
Always wear a helmet, gloves,
trousers (tapered around the cuff
1-7
S-road. (See page 1-5.)
Fa
and anklés0 they do not flap), and
a brightly cotared jacket.
Do not carry tog much luggage on
the scooter. An overloaded scoot-
er is unstable. Use a strong cord to
secure any luggage tothe carrier
(if equipped). A loose loadwill af-
fect the stability of the scooter.and
could divert your attention from the
у r
L Зы
L я,
Вс "e Toh EL
“TT “Ta Е) a
a р. Bs i5 L 15
9 b 3,
> >, DESCRIPTION
8, E | FAL ME
Left view,
a
6,
E
a
Y =
Sy
ga
So ta
6, 6.
2,
E =
e te
TH Ta
co 5,
5 %
“a, =
% |
E
}
%
© Г
=
fg
vis,
“e
=
У
“e ©,
1. Front turn signal light (page 6-28). CA
e. 3, 2. Battery (page 6-25) La, ©. E
“45 3, Helmet holder (page 3-9) HB, e N %
4. Sidestand (page 3-10) 9, % b,
5. Vebelt case alr filter cover (page 6-14) “a,
6. Ceñterstand (page 6-23) e,
7. Air filter{page 6-14) De
8, Rear tur Signal light (page 6-28) “a
“a E 2:1 2 ¿
” 4
Бом = Е’
Fe Ca
го
I ci ut В "o }
>, DESCRIPTION * >, >
e "E
© ©, EAT
Pr
Ta
a
Cr
a
=
i To
со
с
E
: A
Ta
“E -
a
Же
я,
A
tou
) 4
ай
Pe
Sn
>,
E
Ta.
Ca
oF .
ir
=
He
Че
"Eb
“A
LA
. Tall/brake light (page 8:28)
. Muffler (page 3-7) La,
Storage compartment (page‘3-9}
. Seat (page 3-8) %,
. Fuel tank cap (page 3-5) x
“e, 6. Spark plug (page 6-10) e
A Sadi (раде 6-27) >
a “дя
= ил
; dr
de 2-2 e
i’ fl
4
)a nn оо =
=
Tad ue “= Вся
“ Yo i У.
f 195 # ST
"E + TE Ч
EZ, E >,
Ay Be DESCRIF 1 ION
ag Ly
5 6, EAL éd
ba a
Controls and instruments %
%, %,
Tf Ly a
ig 1 2 3 4 5 6 7 4
у Eo
т a fo
2 — > “2
& = — Ч
Ne т “а — | e
e o | *,
o. = В в Ë = E
o = | © 8 ®
4 © e
Ve, “E,
“0. 9
By Г | a
%, “E,
a % — DA a
1 : 3
> Ë Вх и З
я D
“2e, Y
1. Rear brake lever (page 3-5) LS 9. Main switch/steering lock (page 3-1) %
25 Left handlebar switches (page 3-4) = N Bs,
3. Speedometer unit (page 3-3) % A A By
д Fuel gauge (page 3-3) “E, % 2
E
5, Front brake fluid reservolr (page 6-21) +,
6. Right handlebar switches (page 3-4) E
7. Front brake lever (page 3-5) o
8. Throttle grip (pagé:6-16) “a,
2, 2-3 Wa
Li Li
ef
y
A
La
ей
и
Ч
or
“Main switch/steering lock
A
INSTRUMENT AND CONTROL FUNCTIONS
EAU
The main switch/steering lock controls
a %. the ignition and lighting systems, and is
ah Le
J
|
“used to lock the steering. The various
pasitions are described below.
TIP. |
The main switch/steering lock is
equipped With a keyhole cover. (See
page 3-2) 4
К
Ly,
>
o ЕАШТ2271
ON *
All electrical circuits are | plied with
power, and the meter lighting and tail-
light come on, and the engine can be
—6 started. The key cannot be removed.
“E
"о я
TIP To lock the steering
The headlight comes on automatically
when the engine is started and stays on
until the key is turned to "OFF". "E,
E&LNCEHD
OFF
All electrical systems are off. The key
can be removed.
ANTENA
Never turn the mm to “OFF” or
"LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which mE in
loss of control or an accident.
Ewa 1008:
1. Push.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the "OFF" po-
sition, and then turn it to "LOCK"
while still pushing it.
3. Remove the key.
te
LOCK a
The steering is locked, and all electrical +
systems are off. The key can be re-
moved. ] Te
il rw
" u“
ia Fr
F ; E
He
Aou)
Le.
EAUTEtIZ
Keyhole cover
1. Turn. oy e
2. Release. %, | 1. Keyhole cover lever
Push the key in, and Hen tum it to T
o open the keyhole cover
"OFF" while still pushing it. “=. pe у
>, Insert the key bow into the keyhole cov-
By er receptacle as shown, and then turn
the key to the right to open the cover.
“To close the keyhole cover
Push the keyhole cover lever inward
and’ The keyhole cover will close.
INSTRUMENT AND CON ROL FUNCTIONS °
Bal a —
Le Le
fo
EAL 1004
Indicator lights and warning
light Ty,
>,
1. Tur sigñal indicator light “<S >"
2. High beam indicator light “ED”
3. Engine trouble Wa ning light * 3"
E
EALTICE
Turn signal indicator fight ‘ко ое”
This indicator light flashes. when the
tum signal switch is pushed tóme left or
right. o
© сли ну
High beam indicator light “=p” Bs,
This indicator light comes on when the ©
high ban € of the headlight is switched
on. 2
CLE
NT AND CONTROL FUNCTIONS
6 EALIT EOS
Engine trouble warning: light a
This warning light flashes dfstays on if
an electrical circuit monitoring the en-
gine is not working correctly. If this oc-
curs, have a Yamaha dealer check me
self-diagnosis system.
The electrical circuit of the waming light :
can be checked by tuming the key to
“ON”, The warning light should come
on for a few Seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
orifthe warning light remains on, have
a Yamaha dealer check-the electrical
circuit. By
=
бя
F "o
EAT 1822
Speedometer unit
1. Speedometer
2. Odometer
The speedometer unit is equipped with
a speedometer and an odometer. The
speedometer shows the riding speed.
The odometer shows the total distance
traveled.
3-3
FALTA
1. Rael gauge
The fuel‘gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E" (Empty) as the fuel level
decreases. When the needle reaches
"E", refuel as soon as possible.
TIP
Do not allow the fuel tank to ТРУ itself
completely. &
“E,
AM
>,
Que KE to
Ya, a Vo
pa
«?
[=
Ls
noo EE EAUOMH rT e canot with the us See page 5-1 for start-
Handlebar switches =, Dimmer switch “0/50 ing instructions pa to starting the en-
Set this switch to “=p" for the high але.
Left В beam and to “go” for the low beam. y TE
we EAU 3481 “у
“Turn signal switch “</=>" Te
To signal a right-hand turn, push this a.
switch to ">". To signal a left-hand %.
turn, Push this switch to "<=". When re- _ oy
leased, the switch returns to the center = =
position. Te, cancel the turn signal "+ &
lights, push the switch in after it has re- i
turned to the center position. “e
1. Dimmer switch “30/806, с
2, Turn signal switch "<a/ >". EAU12501
3. Hom switch “we” Be Horn switch “ bh ” %
Right Press this switch to sound the hom. ! 6.
J
Tu ЕМ/12861 e
“%, Engine stop switch “O5” Sa,
Set this switch to "7" before starting %
thé“engine. Set this switch to “=” to Tas
| stop the engine in case of an emergen- KC
J cy, such’as when the vehicle overtums =.
or when theithrottle cable is stuck. E %
ESLHZT13 Era
Start switch “©” +
Push this switch to crank the engine +
1. Engine stop switch "O
2, Start switch “@" E
DO,
A, 3-4
<
Y
i
INSTRUMENT AND CONTROL FUNCTIONS
=
©. EAU EAS?
Front brake lever E, Rear brake lever
1. Front brake lever Y. 1 1. Rear brake lever
The front brake lever 15 located. on the The rear brake lever is located on the
right side of the handlebar. To apply the left side of the handlebar. To apply the
front brake, pull this lever toward the rear brake, pull this lever toward the
throttle grip. ©, handler grip.
jr EAUTSXH2
1. Fuel tank Bap
To open the fueltank cap
Insert the key into the dock and turn it 1/
4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened. A,
a
a
ci
To close the fuel tank cap < Bs
1. Push the fuel tank cap into position,
with the key inserted in the lock.
2, Tum the key counterclockwise to
the ‘original position, and then re-
move tk
TIP %
The fuel tank cap cannot be closed un-
less the key is in théjock. In addition,
6
i
a
=D
E
of
A,
he
ml
"ыы vum
<
a“
Ha
the key cannot be removed if the cap is
not properly closed and La
EAT Tr
Make sure that the fuel nk cap is
properly closed after filling fuel.
Leaking fuel is a fire hazard,
INSTRUMENT AND CONTROL FUNCTIONS
EAT
Fuel
Make sure there is sufficient gasoline in
the tank.
Gasoline and gasoline vapors are
Era ion
“i extremely flammable. To avoid fires
‘and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-
gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters and
clothes dryers.
2. Do not overfill the fuel tank. When
refueling, be sure to insert the
“pump nozzle into the fuel tank filler
“hole. Stop filling when the fuel
reaches the bottom of the fillers
tube. Because fuel expands when
it heats up, heat from the engine or
the sun can cause fuel to spill out
of the fuel tank.
3-6
42. Maximum fuel level
1. Fuel tank filler tube 5
3. Wipe up any spilled fuel immedi-
ately. NOTICE: Immediately wipe
off spilled fuel with a clean, dry,
soft cloth, since fuel may deteri-
orate painted surfaces or plastic
parts.ecaiors 7
4. Be sure to secdrely close the fuel
tank cap. ;
a EWALSIN2
Gasoline is poisonous and. can
cause injury or death. Handle gaso-
line with care. Never siphon gaso-
line by mouth. If you should swallow
some gasoline or inhale a lot of gas-
oline vapor, or get some gasoline in
INSTRUMENT AND CONTROL FUNCTIONS
E
of
a,
he
your eyes, see your doctor immedi-
ately. If gasoline spills on your skin,
wash with soap and water. If gaso-
line spills on your clothing, change
your clothes.
Fée
A
7
Recommended fuel
Unleaded gasoline only
Fuel tank capacity:
6.0 L (1.59 US gal, 1.32 Imp.gal)
NOTICE |
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
Cas well as to the exhaust system.
Your Yamaha engine has been de-
signed to use unleaded gasoline with a
pump oétane number [(R+M)/2] of 86 or =
higher, or airesearch octane number of
91 or higher. fi knocking (or pinging) oc-
curs, use a gasoline of a different brand
or premium unleaded fuel. Use of un-
leaded fuel will extend spark plug life
and reduce maintenance costs.
Gasohol %,
There are two typés, of gasohol: gaso-
hol containing ethanol and that contain-
ing methanol. Gasofig| containing
ethanol can be used if the ethanol con-
tent does not exceed 10% (E10). Gas-
ohol containing methanol is, not
“recommended by Yamaha because it
can cause damage to the fuel system.
or vehicle performance problems.
TA
ci,
a
=
e =
“E
EAU si
Catalytic converter ©
This model is equipped with a catalytic e
converter in the exhaust system.
EA OE
ÁN WARNING E
The exhaust system is hot after op-
eration. To prevent a fire hazard or
burns:
e Do not park the vehicle near
possible fire hazards: such as
grass or other materials that
easily burn.
® Park the vehicle in a pláve
where pedestrians or children.
are not likely to touch the hot
exhaust system.
* Make sure that the exhaust sys-
tem has cooled down before do-
ing any maintenance work.
* Do not allow the engine to idle
more than a few minutes. Long
idling can cause a. buiid- -up of
heat. =
À
—
se A
Use only unleaded gasoline. The. use
of leaded gasoline will cause unre- :
Que
Y
5
Ti
INSTRUMENT AND CONTROL FUNCTIONS:
E
e
Ls
E
pairable damage to the catalytic
* converter.
%,
a
=
"а
oy
a
e
2,
e
Th,
E.
Ca
Ss,
a
Ue
KC
xl
Co
=e
Ч
5.
Ta
EAUTS671
Le
3
Seat e
1. Open, 7,
To open the seat.
1. Place the scofgr on the center-
stand.
2. Insert the key into thé main switch,
and then turn it counterelockwise
to the "OPEN" position. If the main
switch is in the "ON" position Aum
the key clockwise to the "OPEN:
position. The seat will fold up auto- *,.
Matically.
TIP _
Do not pusficinward when tuming the
key from “OFF“to "OPEN" or from “ON”
to “OPEN”. %,
sills
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the main
TIP
switch if the scooter will be left un-
attended.
Make sure that the seat is properly se-
“,cured before riding.
E
I
har =
a, y
INSTRUMENT AND CONTROL FUNCTIONS
exe To release the helmet from the hel-
Helmet holder
1. Helmet holder
The helmet holder is located under the
seat
To secure a helmet to the helmet
“+ holder
“4,1. Open the seat. (See page 3-8.)
2_Attach the helmet to the helmet
Holder, and then securely close the
seat. WARNING! Never ride with
a helmet attached to the helmet
holder, since the helmet may hit
objects, causing loss of control
and possibly an accident. zwaoie
met holder >.
Open the seat, remove the helmet from
the helmet holder, and then close the
seat. 7
-
Y
val
Ll
a
— En
=.
Y
5
1. Storage compartment "A
The storage compartment is located
under the seat. (See page 3-8.)
When storing the Owners Manual or
other documents in the storage com-
partment, be sure to wrap them in à
plastic bag so that they will not get wet.
When washing the vehicie, be careful
not to let any water enter the storage
FOMpariort
EW 10252
= Do not id the load limit of 5
kg (11 Ib) for the storage com- Le
partment.
* Do not exceed the maximum
load of 155 kg (342 Ib) for the ve-
ml
tk,
Te
LA
=
INSTRUMENT AND CONTROL EUNCTIONS
hicle.
<>, Sidestand
БАШНЮ
i —]] e —_]] и -
1. Sidestand
~The sidestand is located on the left side
«of the frame. Raise the sidestand or
“Tower it with your foot while holding the
vehicle upright.
TIP_ +
The built-iñ-sidestand switch is part of
the ignition cireuit cut-off system, which
cuts the ignitiof.in certain situations.
(See the following Section for an expla-
nation of the ignition circuit cut-off sys-
tem.) %
dà WARNING
Evia 102az
The vehicle must not be ridden with
ke
3-10
the sidestand down, or if the sides-
tand cannot be properly. moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control,
Yamaha's ignition circuit cut-
system has been designed to веде |
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly and have a
Yamaha dealer repair it if it does not
function properly. —
“E
E
56
= ae
i
"INSTRUMENT AND CONTROL FUNCTIONS ,
© A
ta EAU rl
Ignition circuit cut-off system “a.
The ignition circuit cut-off system (com- Be
prising the sidestand switch and brake A
light switches) has the following func- Sq
tions. Уч og,
® |t prevents starting when the side- |
stand is up, but nelper brake is ap- %
plied. = 4%
; ® |t prevents starting when either o,
"ía brake is applied, but the Stastano - “a
%, is still down. 2 CN A
> it cuts the running engine when the O.
“4 sidestand is moved down. Ve,
Periodically check the operation of the “A.
ignition circuit cut-off system according “a
to the following procedure. »
y = ы -
L E E.
y Da A
a, “ta,
A A
de o"
6, Е: 3
“E. "As %,
a ых, A La
ty ый
de
| E ` th,
МИ
== =
z= бу
7 С A
Sy Же e
: a, INSTRUMENT AND CONTROL FUNCTIONS
"
a
Chey Ч
М
With the engine turned off: Gy, ÁRN WARNING 3
1. Move the sidestand down. “E * The vehicle must be placed on the Genter-
2. Make sure that the engine stop switch is dma on. stand during this inspection. с
> al io. pri dis brake avolisd Y e If a malfunction is noted, have a Yamaha”.
ep the front or rear brake applied. “а Ya,
5. Push the start switch. Yeu _Wealer check the system before riding. "%.
Does the engine start? “8 a
NO YES | ——
A 1 MA Te
e | Fo LF i
+, With the engine still off: % The sidestand switch may notbe working correctly.
6. Move the sidestand up. — 4, The scooter should not be ridden until
7. Keep the front or rear brake pies. le
checked by a Yamaha dealer. ¿Fr
8, Push the start switch. by He
Does the engine start? 9 “a
= | Lor
YES NO-— ] The brake switch may not be working correct;
т — The scooter should not be ridden until Е
With the engine still running: LO checked by a Yamaha dealer. “a
9. Move the sidestand down. Do +,
Does the engine stall? ig LA
- | YES NO | сч The sidestand switch may not be working correctly. %
y, > Y Че | The scooter should not be ridden until
pi 5 - A :
% The system is OK. The scooter can be ridden. Ч checked by a Yamaha dealer.
Cm >, A =
+, =r
Y
mo
LA
es
с
oF
Le
Inspect your vehicle each time you use it to make sure teenie is in safe operating condition. Always follow the inspection ie
and maintenance procedures and schedules described in the Owner's Manual. |
La EWwaéatilsz
Ak WARNING “a
“Failure to inspect or maintain the vehicle properly increases the, possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
thlé manual, have the vehicle inspected by a Yamaha dealer. "За.
Before Using this vehicle, check the following points: Lo >,
“HEM | ch CHECKS % PAGE
|» Check fuel level in ña tank. a,
Fuel = Refusal if necessary, %, 36 de
| * Check fuel line for leakagé: |
| « Check oil level in engine. 5 Fre
Engine oil = If necessary, add recommended oil to specified level, 6-11 to.
| * Check vehicle for oil leakage. + Ty
Final transmission ail | = Check vehicle for oil leakage. "a 6-13
| = Check operation, *
« If soft or spongy, have Yamaha dealer blest ycraulic system.
| « Check brake pads for wear. y
| Чт, brake " Replace If necessary. % 6-20, 6-21
« Check fluid level in reservoir. O,
% » If necessary, add specified brake fluid to specified leña,
te * | * Check hydraulic system for leakage. “# 1 =
K « Check соо 8 Вс *
: « Lubricate cable necessary, a HM
Rear brake “ + Check lever free p ly GTR,
| * Adjust if necessary, >, >
О Tl наи.
Чи
FOR YOUR SAFETY - РВЕ-ОРЕВАТЮМ СНЕСК$
3
de Ё
io
A
С
hs
ый
“4.2
de
4
FOR YOUR SAFETY — PRE-OPERATION CHECKS
5. x
ITEM “5 CHECKS PAGE “Io
|| bd felis.
* Make sure that operation is men. a,
« Check throttle grip free play. ©
Throttle grip * |f necessary, have Yamaha dealer adiust throttle grip free play and lubricate cable B16, 85d *
and опр housing. €
= Make sure that operation is smooth. To
% | Control cables « Lubricate If necessary. v 6-22
4 | « Check for damage. "o,
= « Check tire condition and tread depth. “e
Wheels and tires = Check air pressure, A 6-17, 6-18
ty = Correct if necessary. ty
e * Маке sure thatoperation is smooth. E E
Brake ley "E, | « Lubricate lever pivoting points if necessary. Be 623, 1
L | * Make sure that operation is smooth. e Ta,
coma skdstmd = Lubricate pivots if sary. Te i.
| = Make sure that all nuts, bols and screws are property tightened. ae
Chassis fasteners « Tighten if necessary di — “In
instruments, lights, signals | = Check operation. =, | _ te,
and switches + Correct if necessary. E " “E
“Engine stop switch | « Check operation. = 3-4 =
i = Check operation of ignition circuit cut-off system,
y =destand eviieh * If system is not working correctly, have Yamaha dealer check vehicia E
L LA “a 2 »
fx E
e. “e,
& AL
Hy ; fo
Чи че у =
Fa "E и To, La P
> A ec 1 L
> va 7 Pa
ty и
> E
LA La
о : a.
2
Е
Fe
Lee
OPERATION AND IMPORT
CLE
NT RIDING POINTS
Eases
Read the Owner's Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
= EJANOETZ
7 EIN TD
Failure to familiarize yourself with
-
bo
>
the éontrols can lead to loss of cor
trol, which could cause an accident “scrank when pushing the start switchs,
or injury. >
e
E
EMI
TIP >
This model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the, engine after a
turnover, be sure to tum the main
switch to “OFF” and then tó*ON”. Fail-
ing to do so will prevent the engine from
, starting even though the engine. will
a
ah
BL
a
>, ¿ 5-1
Ebro
Starting the engine ©
See page 5-3 for engine break-in in-
structions prior to operating the ve-
hicle for the first time.
In order for the ignition circuit cut-off
system to enable starting, the sides-
tand must be up. =
See page 3-11 for more infögmation.
1. Turn the key to "ON" and make
sure that the engine stop sich |5
set to “y”.
The engine trouble warning ig
should come on for a few seconds,
then go off. NOTICE: If the warn-
ing light does not go off, have a
Yamaha dealer check its electri-
cal circuit.gcariizy
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the front
or rear brake. 4,
If the engine does по start, re-
lease the start switch, wait a few
seconds, and then try again. Each
starting attempt should be as short,
a
re
ETA Fa
O
Ch
nl
“о
PERATION AND IMPORTANT RIDING P NTS
as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one at-
tempt.
ECAt 1045
For maximum engine life, never ac-
*. celerate hard when the engine is
“gold!
т =
cr
Les Fa
I
ESAS
Sta rting off
1.
While pulling the rear brake lever
with yourdeft hand and holding the
grab bar with your right hand, push
the scooter offithe centerstand.
. Sit astride the seat, and then ad-
just the rear view mirrors.
. Switch the turn signalson.
. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off, =
“5. Switch the turn signals off.
a=
т
E
2 de: 5-5
GEAUTéTé:
Acceleration and deceleration
By 6 (a) tu
La
The speed can be adjusted by « opening
and closing the throttle. To increase the Aa
speed, tum the throttle grip in direction
(a). To reduce the speed, turn the throt-
tle grip in direction (b). E, |
+
г
о
1
OPERATION AND IMPORTANT RIDING POINTS ^^
a
ся
ой
EARLIER
Braking
e EWA 10801
® Avoid braking hard or suddenly
(especially when leaning overto
one side), otherwise the scooter
may skid or overturn.
® Railroad crossings, streetcar
rails,ciron plates on road con-
struction sites, and manhole
covers become extremely slip-
pery when wet. Therefore, slow
down when approaching such
areas and cross sm with cau-
tion.
*e Keep in mind that braking on a
wet road is much more difficult.
® Ride slowly down a hill, as brak-
cult.
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually in-
creasing the pressure.
EXE
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the following
tips to reduce fuel consumption:
e Avoid high engine speeds during
Tae acceleration.
.. Avoid high engine speeds with no
“load on the engine.
5 Turn. | the engine off instead of let-
ting it'idle for an extended length of
time (e.g., in traffic jams, at traffic
lights or at railroad crossings).
ing downhill can be very diffic
5-3
"Aa
E EAL 6831
Engine break-in
There is never a more important period
in the life of yourengine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the follow-
ing material carefully. By
Since the engine is brand new, do not
put an excessive load on it for Де first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
te. the correct operating clearances:
During this period, prolonged full-throt-
tle opération or any condition that might
result in “engine overheating must be
avoided, LT
EALTESS3
0-150 km (0-90 тб ta,
Avoid prolonged operation above 1/3
throttle.
After every hour of operation“ “stop the
=. engine, and then let it cool for fivé'to ten
“minutes. By
Vary the engine speed from time to
time? Do not operate the engine at one
set th rotile portan.
a,
"OD
OPERATION AND IMPORTANT RIDING POINTS
150-500 km (90-300 mi) saura ©,
Avoid prolonged operation above 1/2 Parking Ч,
throttle. a When parking, stop the engine, and %,
Rev the engine freely , through the then remove the key from the main Cr
gears, but do not use full throttle atany Switch. 5
time. o EWAICHZ "Ч,
500-1000 km (300-600 mi) “ae ® Since the engine and exhaust 1 e.
Avoid prolonged operation above 3/4 system can become very hot, >
thréttle. NOTICE: After 1000 km (600°: — park in a place where pedestri- Ba
mi) of operation, the engine oil must ‘=, ans or children are not likely to 5.
be changed and the oil strainer “touch them and be burned. + M
cleaned. ¡có ® Do not park on a slope or on sols,
“6, ground, otherwise the vehicle "2,
1000 km (600 mi) and beyond may overturn, increasing the >.
Avoid prolonged full:throttle operation. risk of a fuel leak and fire. he
Vary the speed occasionally. ® Do not park near grass or other 4,
da ECATDET! flammable materials which м
NOTICE fa might catch fire. к
If any engine trouble should occur "% к
during the engine break-in period, Lo
immediately have a Yamaha dealer Rg
cing the vehicle. 6, 3. Е:
3 b, Ze,
CLE
PERIODIC MAINTENANCE AND ADJUSTMENT
= hy
+,
mi
a
LE
e БРАЛ Тао
Periodic inspection, adjustment, and lu-
brication will keep your vehicle in the
safest and most efficient condition pos: Е
sible. Safety is an obligation of the vehi-
cle owner/operator. The most important
points of vehicle inspection, adjust-
ment, and lubrication are explained on
the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a genétfa) guide under
normal riding conditions. However, de-
pending on the weather, terrain, geo-
graphical location, and individual use,
the maintenance intervals may need to
be shortened.
Failure to properly maintain the ve-
hicle or performing maintenance ac-
tivities Incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle ser-
vice, have a Yamaha ое perform
service.
EVA TONES
ES ÁN WARNING
EAST
Turn off the engine when performing
maintenance unless otherwise
specified.
% e A running engine has moving
| parts that can catch on body
“parts or clothing and electrical
parts that can cause shocks or
fires. >.
# Running. the engine while ser-
vicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning — possibly leading to
death. See page 1-4 for more in-
formation about carbon monox-
ide.
Ena 15461
Brake discs, calipers, drums, and
linings can become very hot during
use, Tor avoid possible burns, let
brake components cool before
touching them,
6-1
EAU 7300
Emission controlémot only function to
ensure cleaner air, but are also vital to
proper engine operationand maximum
performance. In the following periodic
maintenance charts, the services relat-
ed to emissions control are grouped
separately. These services require
specialized data, knowledge,
equipment. Maintenance, replacement,
or repair of the emission control devic-
es and Systems may be performed by
any repair establishment or individual
that is certified: {if applicable). Yamaha
dealers are traiñed and equipped to
perform these panujar services.
A
Ч
pe
and,
e
ea E = a
E He Le, xo
CA PERIODIC MAINTENANCE, AND ADJUSTMENT
Ш
Ca"
3
x
EATER
Owner's tool kit — 7e
AS Is SO | | LA
= A A
AA
Ea a 1
1. Owner's tool kit™, NA
a“
The owner's tool kit i$ located inside the €.
storage compartment tmder the seat. Ч
(See page 3-8.) CH Y
The service information included i in this o,
manual and the tools providedyin the 4
owner's tool kit are intended to assist ta,
you in the performance of preventive, 5
maintenance and minor repairs. How- Be
ever, additional tools such as a torque * %
wrench may be necessary to perform ©, ©. =
certain ma ntenance work correctly. "Ч. 1, %
pari с
a E, я
TIP KM
If you do not have“the tools or experi- %,
ence required for a particular job, have 4
a Yamaha dealer perform it for you. “E,
Ce
Ч Fe
J C Е 6-2 Ú Я
ly a!
if +
A
3
45
+
PERIODIC pa AE AÑD ADJUSTM ENT as %
=
TIP E
e From 12000 mi (19000 km) or 36 months, repeat the maintenance intervals starting from 4000 mi (7000 km) or 12
months.
e [tems marked with an asterisk reguire special tools, data and technical skills, have a Yamaha dealer pérform the service.
Fi E
Al a
a, Эа
> i. E №
> Ч = Bh
da Hy i Wr, E
= de E: “EL
Ta La Pa Lay
ty ¿A
LA "A
Ч ef
E ©
Gt Fa
8 i,
E, "E
3 2
Os 5,
Ls г, =
Ú Ww
y y
fire oy
>
“E LA
Len “а
gels
©, E.
À a
"а Ч.
© a. E Elo
o o = *
Je Le = | a
J de 5 ca
Fi 2
rl Ч
т “a
> E
A da
ve Dy
6, зы
ax Co
E -
hy E
Ч k
A =
6-3 é
5 i
С
a
D. “o >». EA
1 E + ia L L 3
© PERIODIC MAINTENANCE AND ADJUSTMENT
с E
&, ©, EAU 7é82
Periodic maintenance chart for the emission control system =
%, | INITIAL ODOMETER READINGS
(0 6000 mi 8000 mi 10000 mi
4 600 mi 2000 mi 4000 mi
No. ITEM ; | ROUTINE (1000 km) | (4000 km) | (7000 km) “poo (1 2400 (1 po
GE m m
5 or or or |
SE or or or
a 1 month 6 months | 12 months 18 months i Sais | 0 meniba
| Cle EL .
« Check fuel hoses for cracks or a
1 | * | Fuel line damages, Y y Y KA, Y
- * Replace ifnecessary. o Ta,
a « Check conditièn. "a Ч
à] s Adjust gap and'élean. ‘$ Ч
2 | {Spark plug * Replace at 4000 mi (7000 km) or Y Replace. Y Replace. y
ts 12 months and thereafter avery A
Ge 4000 mi (6000 km) or 12 months. “e
а | * | valve ch ‘ar « Check and adjust valve clearance J J “a J J J
Es, when engine is cold. *,
чо = “
| rene mer | care roro [Ma | Ea
system “+ | » Replace if necessary. a
5 | * | Fuel injection #4 « Check engine idle speed. | y y Ta Y y
| "Check for leakage. Va
6 | * | Exhaust system = Tighten if necessary. Y Y A 4 y y
* Replace gasket(s) if necessary. Ч
i xr =
Cy CH
"D ee “5 “e
Is > 5 L ;
( с Thy 2, hy
LA ta
4, A
+ 5
Fig L
Yo “a
> a.
Ue Ks
Ly ir)
©. os
e
€, ЕАЦЗ2129
General maintenance and lubrication chart a
| INITIAL ODOMETER READINGS
6000 mi 8000 mi 10000 mi
600 mi 4000 mi
d ITEM ROUTINE (1000 km) (7000 km) (10000 (13000 (16000
= km) km) km)
"% Поли Das months ar of ст
© = a 18 months | 24 months | 30 months
aa | E
Air filter element * Replace. e! y
V-belt case air filter | | Tb. E
element iM | len: ee | УЧ” : *e
Tha, |» Check operation, fluid level, and | | Pa
Front brake + for fluid leakage. A Y E y + y
| * Replace brake pads if necessary. 1%.
| * Check operation. | 6.
Rear brake * Adjust cable and replace brake Tn Y Y Y Y
shoes if necessary. e
| * Check for cracks or damage.
| * Check for correct routing and Y y y y
Brake hose clamping.
* Replace. Every 4 years
re * Check runout and for damage, | | | |
Wheels “ Replace if necessary. к * 4 * Y
Hy, | * Check tread depth and for "
» damage. Ye
Tires % |» Replace if necessary. Y Y Y
O. | « Check air pressure. ; oy o.
‘a, | * Correct if necessary. a, ús
“3, | » Check bearings for smooth ® |
Wheel bearings operation. o Y Ч | y
+ Replace If necessary. ”
DE
©
+
rt = = E e E
ET a or, xg
CA PERIODIC MAINTENANCE AND ADJUSTMENT *
Ч
Te, INITIAL ODOMETER READINGS
Ls A
LEA ; 6000 mi 8000 mi | 10000 mi
Ч 600 mi 2000 mi 4000 mi “Ez
t “a
No. (TEM ¿, ROUTINE (1000 km) | (4000 km) | (7000 km) ere % Gan) orice
J or or or ЧЁ
4 or or or
| © 1 month | 6months | 12 months | 48 months 24 moriths 30 months
« Check ie semble for Gi
loosaness. a Mo Ч
: » Moderately repack w | | | | Ч
9 steering bearings lithium-soap-basad gr 6 every Y Y Y Y Repack. %
. 8000 mi {13000 km) or 24%; 4 в ty
E months. | > A
Ne | = Check all chassis fitting and A — | "а
10| * | Chassis fasteners fasteners. Ч, y j 8 hy y y y =
4, | * Correct if necessary. CN
Front brake lever Fl i | Eu
11 pivot shaft E Apply silicone grease lighthy. Y Y %. y Y
19 Rear brake lever * Apply lithium-soap-basad graass J J J С J J
pivot shaft | Le TE.
| * Check operation. kr
| « | Centerstand and | J | бя u
13 sidestand pivots - übe Inia AnHp-tee sl grease Y y Y oY, | y
№ г.
|= i i i i Fe He
14| * | Sidestand switch carter replace if ; : Я T y y
| (AA
+ Check operation and for oll | e
15) * | Front fork leakage. a Y y y y AL
* Replace if necessary. к +
= "= Check operation and for oil | = Lo
=| Dock anil leaka ay, | J ds J y y %
assemblies” TE 5) L ©
CM = Replace if necessary. к 2 >
“2, | » Change (warm engine before | Ч
fe | draining). | | Ei
12 Engine oil te Check oil level and vehicle for oil Y à x 2 Y
| “leakage. | я
18] | Engine oil strainer | = Clean, | Y y a, y
+, 6-6 Be
E
La
=
Ч
Qu
"o
E
и
чл Í
PERIODIC MAINTENANCE AND ADJUSTMENT ^^.
I
a) INITIAL ODOMETER READINGS
Ta
FOR. TE E в
% 600 mi | 2000mi | 4000mi соо, 3000 oD
No. ITEM 2, ROUTINE (1000 km) | (4000 km) | (7000 km) A
Gr dé e Un km) “a km) km)
ka 1 month | 6 months | 12 months | ,, nie 2 a Moniha 20 merlin
| Куй
19| | Final transmission |» Check vn oil leakage. J J JB,
oil | * Change. Зы ЗАД
20 V-belt | = Replace, E Every 11000 mi (18000 km) ho
Front and rear brake | La , Ta
2 *| ei h | Check operation. bs, | y y ©. y y | a,
* Apply Yamaha cable lubricant or o CN
22 Control sind meter other suitable cable lubricant >. Y y Vg, y y y “Y
LA | thoroughly. | CM
“dg, * Check operation. He
6. | = Check throttle grip free play, and | | В
23| * | Throttle grip a adjust if necessary A * oF Y
‘4 Lubricate cable and grip housing. En
Lights, signals and | * Check operation. | ' | | | 6
“| | switches + Adjust headiight beam. : | A
=
%, Sip
E “5,
to Le
€ ©
TIP Ta с
® Air filter and V-belt filter “a =
pressed air to avoid damaging it. "So
usually wefor dusty areas.
® Hydraulic brake ‘service
E “5
E
* This model's air filter is equipped with &gisposable oil-coated paper element, which must not be cleaned KC :com-
Ta,
* The air filter element needs to be replaced año V-belt filter needs to be serviced more frequently when riding in uns,
« After Senseo the brake master cylinder and caliper, always change the fluid. Regularly check the brake fluid
level and fill the re Ч as required.
LC
E,
6-7 A,
En if
y ai
eg es
a “2
. PERIODIC MAINTENANCE AND ADJUSTMENT
« Every two years replace the internal com ponents of the brake master cylinder and caliper, and change the rake fluid.
Cs
=
=
Replace the brake hose every four years. Re if cracked or damaged.
Го
=
Пн
L
e
i L
a
o
A
=
IL ï
E E,
wt ls
r
E
“9.
| Li
Fa Tal
= = a
La ry
a
ne a
E E "MA
5 +
= E
om FN
Les Li
Ё
©,
be,
я
TO
Ea
.
T
i я
ci
A
+3 ы
CA
is
Ly,
E
E
A
“ak
Г к.
"A ==
ta E
to
hs al |
LA P
Е Flt E
2h A
y A al
e =
т” ли
E "
Бо Tar
wo
>,
“> PERIODIC MAINTENANCE AND ADJUSTMENT %
5 ving and installing or “6, 0 FanslB
dese. Panel A KC - |
The panels shown need to be removed
to perform sóme of the maintenance
jobs described (Athis chapter. Refer to
this section each a panel needs to
be removed and installed.
1. Panel A —
2. Panel B “a.
Remove the screw, and then pull out-
ward on the areas shown.
1. Panel A
2. Screw
Place the panel in the original position,
and then install the screw.
6-9 ke”
1. Remove panel A.
4 e Remove the screws and the quick
By fastener screws, and then take the
‘panel off
MA
4 1. Panel B
e. Screw
3. Quick fastener
“a,
To install
1. Place the panel in the original posi-
tion, and tl en install the screws
and the quick;fastener screws.
2. Install panel A.
“a
EXLITÍ MA
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
“the condition of the spark plug can re-
veal the condition of the engine. “+
To remove the spark plug
1. Place the vehicle on the center-
stand.
2. Remove panel B. (See page 6-9.)
3. Remove the spark plug cap.
4. Remove the spark plug as shown,
with the spark plug wrench includ-
ed in the owner's tool kit.
af №
1. Spark plug wrench }
To check the spark plug
‘4, Check that the porcelain insulator
‘around the center electrode of the
spark plug is a medium-to-light tan
(the ideal color when the vehicle is
ridden nörmally).
TIP
If the spark plug shows a distinctly dif-
ferent color, the enging could be oper-
ating improperly. Do not attempt to
diagnose such problems yourself. In-
stead, have a Yamaha dealér check
7, the vehicle.
7. Check the spark plug for electrode
“æ@rosion and excessive carbon or
other deposits, and replace it if
6-10
Pas
a. PERIODIC MAINTENANCE AND ADJUSTMENT
Los
necessary. E.
Specified spark plug: “a
DENSO / U22ESA-N a
To install the spark plug
1. Measure the spark plug gap with a
wire thickness gauge and, if nec-
essary, Aquat] the gap to specifica-
tion.
Spark plug gap:
0.7-0.8 mm (0. 028-0, ‚бал in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads. Cr
3, Install the spark plug with the +.
spark plug wrench, and then tight-
en it to the specified torque.
Tightening torque:
Spark plug;
13 Nm (1.3 kgf, 9.4 ft-Ibf)
TIP “a,
If a torque wrench is not available when
installing a spark plug, a good ‘estimate
of the correct torque is 1/4-1/224urn
“E
he
PERIODIC MAINTENANCE AND ADJUSTMENT
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.
4. Install the spark plug cap.
5. Install the panel.
я m
La
de, я
ли,
© EAUTZS87
Engl, oil
The enginépil level should be checked
before each” ride. In addition, the oil
must be changed and the oil strainer
cleaned at the intervals specified in the
periodic maintenance: and lubrication
chart. %
To check the engine oil level,
1. Place the vehicle on the denter-
' %, stand. A slight tilt to the side can
result in a false reading.
> “Start the engine, warm it up for
several minutes, and then tum it
%,
1. il filer cap
2, Mékimum level mark
3. Minimum level mark
4, 8-11
KC
3, Wait a few minutes until the éil set-
ties, remove the oil filler cap, wipe
the dipstick clean, insert it back
into the oil filler hole (without
screwing it in), and then remove it
again to check the oil level.
TIP
The engine oil should be between the
minimum and maximym level marks.
4. If the engine oil is below the mini-
mum level mark, add Sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler;
cap.
To change the engine oil
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan ainder the engine
to collect the used oi,
E
he's
Г 5
E
=]
1. Oil filler cap 5
3. Remove the engine “oil filler cap
A and the engine oil drain bolt to
drain the oil from the crankcase.
> 4. Install the engine oil drain bolt, and
“, then tighten it to the specified
| “orque.
Tightéhing torque:
Engine oil drain bolt:
20 Nm (2,0 m-Kgf, 14 ft-Ibf)
5. Refill with mé specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap. a
= Ro
Ls
| PERIODIC: MAINTENANCE AND ADJUSTMENT
it for oil leakage. If oil is leaking, im-
Recommended =r ql |
mediately turn the engine off and
See page 8-1. b,
Oil change quantity: “E, check for the cause.
0.85 L (0.90 US at, 0.75 Imp. a. 7. Turn the engine off, and then
ce check the oil level and correct it if
E necessary.
e. Do net use oils with a diesel e,
specification of “CD” or oils of a pA
higher quality than specified. In %
addition; do not use oils labeled Te,
“ENERGY › CONSERVING Il” or E
higher. A
® Be sure no foreign material en-
ters the crankcase.
\
8,
. Engine oil drain bot
6. Start the engine, Fn then let it idle
for several minutes while checking
%
6-12 3e
F
E
i
E
“6, EALENDE?
Final transmission oil
The final transmission case must be
checked for oil. leakage before each
ride. If any leakage is found, have a
Yamaha dealer cheek and repair the
scooter. In addition, the final transmis-
sion oil must be changed as follows at
the intervals specified in the. periodic
maintenance and lubrication chart.
|. Start the engine, warm up the final
%, transmission oil by riding fhe
“scooter for several minutes, and
then stop the engine.
2. Plate the scooter on the center-
stand’,
3. Place a cil pan under the final
transmission case to collect the
used oil. Ta
4. Remove the final transmission oil
filer cap and its O- ing. from the fi-
nal transmission case.
%
“A
©.
Eu
Ч
PERIODIC MAINTENANCE AND ADJUSTMENT
1. Final transmission oil fille” gap
L
5. Remove the final transmission oil
drain bolt and its gasket to.drain
the oil from the final transmission
case. o
T E i ÉS i
1. Final transmission oil drain bolt 75
=
6. Install the final transmissiof oil
drain bolt and its new gasket, and,
6-13
then tighten the bolt to the speci-
fied torque.
1. Tightening torque:
‘Final transmission oil drain bot.
es Nm (2.3 m-kgt, 17 ft-Ibf)
7. Refill with the specified amount of
the recommended final transmis-
sion oil. WARNING! Make sure
that no foreign material enters
the final transmission case.
Make sure that no oil gets on the
tire or wheel.ema
Recommended final transmission
oil:
“Qil quantity:
See page 8-1.
70.13L (0.14 US at, 0.11 Imp.gt}
8. Install the final transmission oil fill-
er cap and its new O-ring, and then
tighten the:oil filler cap.
9. Check the final transmission case
for oil leakage If oil is leaking,
check for the cause.
ip id = E "ыы и,
> PERIODIC MAINTENANCE AND ADJUSTMENT ^^,
Bum e “e PR the air filter case for accumulated
A Air filter and V-belt case air
“filter elements
The air filter and V-belt case air filter el-
ements should be cleaned at the inter-
vals “specified in the periodic
maintenánce and lubrication chart.
Check botfrsfilter elements more fre-
quently if you “are riding in unusually
dirt or water.
2. If dirt or water is visible, remove
the hose, clean it, and then install
it.
e Cleaning the V-belt case air filter el-
я %, ement
“5 Al. Remove the V-belt air filter case
wet or dusty areas. The air filter check | © : “gover by removing the screws. ©,
hose must be "rea checked and 1. Airfiter case cover | Pa
cleaned if necessary. 2. Screw —
3. Airfilter check Nose
Replacing the air filter element 3. Pull the air filtef ‘element out.
> 1. Place the scooter on the center- 4. Insert a new air filter element into
Sand. the air filter case. NOTICE: Make
2. Remove the air filter case cover by sure that the air filter element is
+ removing the screws. properly seated in the air filter
NR case. The engine should riever
a, DE DRE S ARNOUT TE AN filter 1. V-belt air filter case cover
% element installed, otherwise the“. а crew
a piston(s) and/or cylinder(s) may Ех
“a become excessively worn. cass 2:Remove the filter element holy,
Ч 5. Install the air filter case cover by in- by semoving the screw. у
Y stalling the screws, KY
E Cleaning the air filter check hose
“a A 1. Check the hose onthe front side of
= re
EA eu wy
a "a a
ча [ur Y
E
a
PERIODIC MAINTENANCE AND ADJUSTMENT
"te,
E 1. Air filter element holder a 1. Air filter element E
a + “ds
2, Screw 7 e
“a 4. Apply oil of the recommended type
3. Pull the air filter element out, and to the entire surface of the sponge
then clean it with solvent. After”. material, and then squeeze the ex-
6 cleaning, remove the remaining i cess oil out.
solvent by squeezing the element. TIP
WARNING! Use only a dedicat- a
ed parts cleaning Le ant To The air filter element should be wet but
avoid the risk of fire or explo- " APPO.
sion, do not use gasoline or sol- =
vents with a low flash Recommendedpil: —
5, point.ecæ NOTICE: To avoid mac a
ua damaging the air filter element, 2e,
>, handle it gently and carefully, 5, Insert the element intônthe air filter
- And do not twist it. scams a CASE. =
У
К 6. Install the filter element holder by
“installing the screw.
“47. Install the V-belt air filter case cov-
Ч
Зо 6-15
о >
A
E
7
I Es
er by installing the sérews.
м
fp
a
Le
le
vf
=
y
5
Fry
LA ия
“&
“a
e
1 de
Pa
La
Fed
2
A
“de
a
+ E
a
Y
Fu
Ge,
Un
cn
a
La
“E
e
ó
ih
E
Ф,
5
E,
E,
E.
E
LA
fl
wf
a
PERIODIC MAINTENANCE AND ADJUSTMENT
Ч
E
E
a =
= Г «а
” EALMATIS EALEZT8S E | EALIZ1402
Checking the engine idling Checking the throttle grip free Valve clearance
speed %% play The valve clearance changes with use,
Check the engine idling speed and, if
necessary, have it corrected oF ot C
Yamaha dealer.
Engine idling speed:
1700-1900 r'min
A.
Ч
"=
ca
I ro
A
“+,
Ч
Le
¢
я
$
Vio
Pe
de
2
E
a
6,
É
я
==
5
1. Throttle grip free play
The throttle grip free play should mea-
sure 3.0-5.0 mm (0.12-0.20 in) at the
inner edge of the throttle grip. Periodi-
cally check the throttle grip free play
- and, if necessary, have a Yamaha
“dealer adjust it.
resulting in improper air-fuel mixture
and/or engine noises To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the, periodic
maintenance and lubrication chart.
Ca
Ea
Ce
о
г :
=
2,
de)
Éd
“=
#5,
Ч
a
is
AL
Ta
TE
©
A
LE"
i a}
"E
Sn
7 ét.
Le
+
for
te
бе
4
E
“а
i,
>
=|
Г "6
"J
"A
TE
=
due
Ta
Le
e
>
«+
“E
Ya
we
PERIODIC MAINTENANCE AND ADJUSTMENT
EALÆTTE1
Tires =
Tires are the only’ ‘contact between the
vehicle and the road: Safety in all con-
ditions of riding depends/on a relatively
small area of road contact. Therefore, it
is essential to maintain the tirés.in good
condition at all times and replacethem
at the appropriate time with the ересь
fied tires. 6
Tire air, pressure
The tire air pressure should be checked
and, if do adjusted before each
ride. A
ge САЛО
ÁN WARNING MEZA
Operation of this vehicle with im-
proper tire pressure máy cause se-
vere injury or death from: 3088 of
control.
® The tire air pressure mustobe
- checked and adjusted on cold
- “ tires (.e., when the temperature -
of. the tires equals the ambient
temperature).
e Thetiré air pressure must be ad-
justed in accordance with the
riding speed. and with the total
Ga
“4, 90 kg (198 Ib) to maximum load:
weight of rider, passenger, car- “Tire inspection
go, and accessories approved
for this model.
Tire air pressure (measured on cold
tires):
Up to 90 kg (198 Ib) load:
Front:
175 kPa (1.75 kgf/em°, 25 psi)
Rear:
200 kPa (2.00 kgfem"°29 psi)
Front:
Hear:
225 kPa (2.25 kgficm®, 33 psi)
Maximum load*:
155 kg (342 Ib)
* Total weight of rider, passenger, car-
go and accessories
Never overload your vehicle. Opera-
tion of an overloaded vehicle could
EAST
_cause an accident.
“E
200 kPa (2.00 kgf/omË, 29 psi}*,
cr
GB,
Lo
ZALJE1 166
2
1. Tire sidewall
=. Tire wear indicator
% 3. Tire tread depth
The tires must be checked before each
ride. Af a a tire tread shows crosswise
lines (minimum tread depth), if the tire
has a nail‘or glass fragments in it, or if
the sidewalfs.is cracked, contact a
Yamaha dealer’ oca and have
the tire replaced.
Minimum tire tread depth {front and |
rear): ES,
1.0 mm (0.04 in) Ч
Ewa
“e It is dangerous to ride with a
hm
CLE
PERIODIC MAINTENANCE AND ADJUSTMENT
worn-out tire. When a tire tread
begins to show lines, have a
% Yamaha dealer replace the tire
‘immediately. Brakes, tires and
related wheel parts replacement
shoüld fan be left to a Yamaha
dealer,
¢ Ride at moderate speeds after
changing a“tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics. ——
Tire information
This model is equipped with tubeless
fires and tire air valves.
Tires age, even if they have not been
used of, have only been used occasion-
ally. Cracking of the tread and sidewall
rubber, sometimes accompanied by
carcass deformation, is an evidence of
ageing. Old and“aged tires shall be
checked by tire specialists to ascertain
their suitability for further use.
The front and rear tires should be of
EVA RDA
“the same make and design, other-
9
wise the handling characteristics of
the vehicle may be different, which
could lead to an accident. =
After extensive tests, only the es list-
ed below have been approved for mue
model by Yamaha.
Front tire:
Size:
120 £70 - 12 51L
Manufactürer/model:
KENDA / K761A
Rear tire: By,
Size: |
130 / 70-12 sele
Manufacturer/model: ©.
KENDA / K761 >
бя
Ta.
6-18
EALIZ1563
Cast wheels
To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.
7 ® The wheel rims should be checked
for cracks, bends, warpage or oth-
“er damage before each ride. If any
damage is found, have a Yamahas.
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.
® The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
“&. ened tire life.
he
Жо
PERIODIC MAINTEÑANCE AND ADJUSTMENT
ka
EALHGIST
Checking the front brake lever
free play
1. Front brake lever
There should be no free play at the
brake lever end. If there is free play,
have a Yamaha dealer inspect the
brake system.
A soft or spongy feeling in the brake
lever can indicate the presence of air
_ In the hydraulic system. If there Is air
Sin the hydraulic system, háve a
Yamaha dealer bleed the system be-
EA Ta
fore operating the vehicle. Air in the.
Seguit in loss of control and an acci-
dent.
%
a=
hydraulic system will diminish the ©.
braking performance, which may re-
E 6-19
>
A E E
Adjusting the rear brake | over
free play 6,
1. Rear brake lever free play “2 ©
The brake lever free play should mea-
sure as shown. Periodically спеёк the
brake lever free play and, if necesssyy,
adjust it as follows.
To increase the brake lever free play, 2
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, tum the adjusting
nut in direction th).
E
“ul
Eo KE
Ye #2]
e
Te
_ “PERIODIC MAINTENANCE AND ADJUSTMENT
e a enzo pad has wom to the point that the wear
\ Na Y * Checking the front brake pads “indicator groove has almost disap-
\ WAS and rear brake shoes peared, have a Yamaha dealer replace
The front brake pads and the rear brake
shoes must be checked for wear at the
intervals specified in the penodic main-
tenance and lubrication chart.
Elida
e. Front brake pads
1 Adjusting пы! ay
a EWA DES ty
If proper adjustment cannot be ob-
tained as described, have a Yamaha
dealer make this adjustment.
L}"
1. Brake pad wear indicator groove
E, 2. Brake pad
+ 3. Brake disc
O “a Each front brake pad is provided with a
+ “wear indicator groove, which “allows
LL you to check the brake pad wear with-
out having to disassemble the brake.
“a To check the brake pad wear, check “the wear limit line, have a Yamaha
the wear indicator groove. If a brake
с 6-20
a
J
the brake pads as a set.
y
q EAUSZE41
hy
Rear brake shoes
ir
бах
$
1. wear indicator
2. Wear limit line
Na
The rear brake is provided with a wear
indicator, whichallows you to check the
brake shoe wear without having to dis-
assemble the brake: To check the
brake shoe wear, checkthe position of
the wear indicator while ‘applying the
brake. If a brake shoe has worn to the
point that the wear indicator reaches
dealer replace the brake shoes as a
+
Ll
a
r
a
E
A
€.
oly
"PERIODIC MAINTENANCE AND ADJUSTMENT
To EME
Checking the brake fluid-level
Before riding, check that the brake fluid
is above the minimum level mark;
Check the brake fluid level with the top”
of the reservoir level, Replenish the
brake fluid if necessary.
1. Minimum level mark
e
performance.
* Clean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
_ ® Use only the specified brake flu-
“E id; otherwise, the rubber seals
“may deteriorate, causing leak-
age.
® Refill, with the same type of
brake fluid. Adding a brake fluid
other than:DOT 4 may result in a
harmful chemical reaction.
* Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
— lock.
Specified brake fluid:
DOT 4
EA 15001
Ah WARNING B
Improper maintenance can result in
loss of braking ability. Observe
these precautions: 7.
e Insufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
6-21 у
a BCE
Brake fluid may damage painted sur-
faces or plastic parts. Always clean
up spilled ffüid immediately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate wom brake pads and/or brake sys-
tem leakage; therefore, be sure to
fh?
=
La
E MAINTENANCE AND ADJUSTMENT
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before
further riding.
de
ел
EA
changing the brake fluid
Have a. Yamaha dealer change the
brake fluid. at the intervals specified in
the periodic-maintenance and lubrica-
tion chart. In addition, have the oil seals
of the brake master cylinder and caliper
as well as the braké-hose replaced at
the intervals listed beldi or whenever
they are damaged or leaking.
e Oil seals: Replace San two
years.
, ® Brake hose: Replace every four
“e. years.
a
%, ЕАЦ23000
Checking and lubricating 1 the
cables EM
The operation of all control cables and
the condition of the cables should be 7
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary, If a cable is damaged
or does not move smoothly, have a
Yamaha dealer theck or replace №
WARNING! Damage to the outer
housing of cables may result in in-
ternal rusting and cause interfer-
ence with cable movement: Replace
damaged cables as soon as possi-
ble to prevent unsafe condi-
tions. ewan + a
Recommended lubricant:
Yamaha cable lubricant or other suit-
able cable lubricant
e
A
J
E
a
Ch
nl 7
e,
PERIODIC MAINTENANCE AND ADJUSTMENT
EAvenié
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated by a
Yamaha dealer at the intervals speci-
fied in the periodic maintenance chart.
The throttle cable is equipped with a
rubber cover. Make stre that the cover
is securely installed. Even though the
cover is installed correctly, it does not
completely protect the cable from water
entry. Therefore, use care not to pour
“water directly onto the cover or cable
when washing the vehicle. If the cable
or cover becomes dirty, wipe clean with
a moist cloth.
“E.
EAT
Lubricating the front and rear
brake levers CM
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic main. В
tenance and lubrication chart.
Rear brake lever
Recommended lubricants:
Front brake lever:
Silicone grease
Hear brake lever:
Lithium-soap-based grease
2
о
6-23 € a
1 NGI
ithe centerstand or sidestand does
AUS
Checking and lubricating the
centerstand and sidestand
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and met-
al-to-metal contact surfaces should be
lubricated if necessary.
EA Oda
not move up and down smoothly,
have “a. Yamaha dealer check or re- _
pair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
at vum E mi al ry
E" =a - E
у de ‚
AM PERIODIC MAINTENANCE AND ADJUSTMENT
ESUISTSET
Recommended jubricant. Checking the front fork
РН dragse The condition and operation of the front
4 fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
“To check the condition
Check the front fork for damage ande ех-
cessive oil leakage.
pa E
a To check the operation NER A
% 1. Place the vehicle on a level sur- If any damage is found or the front
"A face and hold it in an upright posi- fork "does not operate smoothly,
v tion. WARNING! To avoid injury, have a Yamaha dealer check or re-
EC securely support the vehicle so pairit.
de there is no danger of it falling -
a [email protected][Pra0sz La
Ve 2. While applying the front brake, |
+ push down hard on the handlebars
several times to check if the front 5,
< fork compresses and rebounds É:
“smoothly. В 6
“Te SEP Fo
e
Y
a,
1 я
6-24
CLE
PERIODIC MAINTENANCE AND ADJUSTMENT
= hy
Si
5,
e, EAST
Checking the steering,
Worn or loose steering bearings. may
cause danger. Therefore, the operation
of the steering must be checked as fol:
EALLIONE
Checking the wheel bearings
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
lows at the intervals specified in the pe-' “stion chart. If there is play in the wheel
riodic maintenance and lubrication
chart.
1. Place the vehicle on the center-
stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
OVEer eva ros
2. Hold the lower еп of the front
fork legs and try to move-them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering,
Hub or if the wheel does not turn
smogthly, have a Yamaha dealer check
the wheel bearings.
fe
Fe
«т.
1
6-25
БАТ оу)
Battery .
This model is eduipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled waler, However,
the battery lead connections fieed to be
checked and, if necessary, tightened.
ED
dà WARNING ;
® Electrolyte is poisonous and”
dangerous since it contains sul-
furic: ‘acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield. your eyes when
working near batteries. In case
of contact, Sami inter the fol-
lowing FIRST AID.
EXTERNAL: Flush van por
of water.
+ INTERNAL: Drink large Guan-
tities of water or milk and im-
9, mediately call a physician. 1
+“ EYES: Flush with water for 15
minutes and seek prompt
medical attention.
® Batteries produce explosive hy-
drogen gas, Therefore, keep
1 *
_ PERIODIC MAINTENANCE AND ADJUSTMENT
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.
® KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
ЕСА!
Néver attempt to remove the battery
cell seals, as this would permanent»,
ly damage the battery.
The battery is located under panel A.
Remove the panel to access the bat-
tery. (See page 6-9.)
To charge the battery
Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
* 1 battery tends to discharge more quickly
“ifthe vehicle is equipped with One
electrical accessories.
To charge a VRLA (Valve Rec
Lead Acid) battery, a special (con-
ЕСА! “e,
Le
“Sétant-voitage) battery charger is re-
quired. Using a conventional battery
cha ger, wa damage the battery.
To store té battery
1. If the vehicle will not be used for
more than one; month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the‘ key is
turned to “OFF”, then discon-
nect the negative lead before
“. disconnecting the positive
“ead. ono
2. Ifthe battery will be stored for more
than“two months, check it at least
once a month and fully charge it if
necessary.
3. Fully charge the battery before in-
stalling it. NOTICE: When install-
ing the battery, be sure the key
is turned to “OFF*-then con-
nect the positive lead before
connecting the negative
lead. erase
24. After installing the battery, make
“sure that the battery leads are
6-26
properly connected to the Battery
terminals.
5. Tum the key from “ON” to “OFF”
three times in three-second inter-,
vals to initialize the idle speed con-7 _
trol system.
EC
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
“., PERIODIC MAINTENANCE AND ADJUSTMENT
© ALTRE:
"a
Replacing the fuses
©. Ne № j Ps
Grd SAN \
— == Te à | y | i
1. Fuse box
“The fuse box is located beside the bat-
Tr
tery, compartment under panel A. (See
page3d-8.)
If a fuses blown, replace it as follows.
1. Tum the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fase of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire. vasta
>
ей
E
a
=n
Specified fuses: [9
Main fuse: “5,
20.0 A “E,
Ignition fuse: & À
10.0 À “lo
Signaling system fuse:
15.0 A
Headlight fuse:
10.0 A
Fuel injection system fuse:
10.,0A $
я
a re
1
TIP 2
After removing and installing the main
fuse, be sure to tum the main switch
from “ON” to "OFF" three‘ times in
three-second intervals to initialize the
idle speed control system. % ,
3. Tum the key to “ON” and turn or
the electrical circuit in question to
check if the device operates.
à. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
=
J
"À
E
"ml
6-27
EAU SEA
Replacing a headlight bulb
This model is equipped with halogen
bulb headlights. К а headlight bulb
bums out, have a Yamaha dealer re-
“place it and, if necessary, adjust the
A
headlight beam.
E
"
"
Sy
Se
За
"ЧР
°
“Ea В
i)
Fa
%
i.
ls,
“o
x
a tor
Fr Lar
ihe +,
&
To
> 5, ls
PERIODIC MAINTENANCE AND ADJUSTMENT
7
EALMSOH @_ Env pushing it in and tuming it counter-
Tail/brake light Replacing a turn signal Tight clockwise.
If the > fail/brake light does not come on, bulb % 3. Insert a new bulb into the socket,
have a Yamaha dealer check its electri- 1, Remove the tum signal light lens. push it in, and then turn it clock-
cal circuit orreplace the bulb. by removing the screw. 7. wise until it stops.
“o. “a. Install the lens by installing the
e “screw. NOTICE: Do not over-
Be tighten the screw, otherwise the
E lens may break.iecariies
a, €,
CN Lo
e x
“E,
hy
Ca
Ca NE
‘2, Ta,
с i $
o a
> Es
Bs Cs
Ma 5,
6 1. Turn signal fight bulb =.
E 2. Remove the bumt-out bülb by
a. 6-28 *
“IGE
al um,
La
a“
"Se
“PERIODIC MAINTENANCE AND ADJUSTMENT
нову
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
% for checking these vital systems your-
self. However, should your scootér re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
EWG TE
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
heaters or fumaces. Gasoline or
“gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.
a
ea, including pilot lights from water ©.
A,
ta
У
E
Toh,
ra
E >
ch
a | Pe a)
À IN DJ
». PERIODIC MAINTENANCE AND ADJUSTMENT
2 T
©. € EAUTICOS
m a =
Troubleshooting chart % a
"a, >,
1. Fuel E ©
Г” Theré ls enough fuel, ds Check the battery “a
Check the fuel level in |
the fuel tank | rr ra anna a Fe
Fe e an does not start, oy
There is no fuel. ще Supply ful. —* Grisciche hairy. 5
or
Se
"Е
2. Battery Loa
do de tums over | el The battery is 90,
| EL. | |
Operate the alaciric starter. < The engine does not Start
| Thé engine tums over Check the battery ead Connections, savait ho halon Le
В =| and have a Yamaha dealét charge a
= the battery à necessary. “ty
7; LP
pi E +
3. Ignition a €
Wer >| Wipe off with a dry clolh and correct the ale Me electric starter A
Spark plug gap, or replace he spark plug pe ©,
and check the electrodes. Ч Чё.
a 7 The engine does not star. “2
| Dry ==) Have a a, dealer check the vehicle. С ep by Go
TT 7
a o
4. Compression + Ч
The ngine does not start
| Themes EA Have &%amaha dealer check the vehicle.
Орегайе the electra: starter e
bal Thereis nó compressión, -—e| Havea Yamafi dealer check the vehicle.
El д
o Bi “o
ds % da
+ “E +
Fa > Ta
Ae de
4. ©.
EN Ga,
Y Y
2 2
a 6-30 e,
Li L
— “i e
E
Э Ln 5 5
L а Le 5
SCOOTER CARE AND STORAGEé к
2 Ge 1 | EAUSTEM onsen ©. ucts onto seals, gaskets and wheel
Matte colorcaution Care “> axles. Always rinse the dirt and de-
“Bi ECAIS198
—
SAGE !
Some models are equipped with
matte colored finished: parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning ™
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-
ished parts. —-.
ie
a
=
À
€,
i
While the open design of a scooter re-
veals the attractiveness of the technol-
ogy, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Fre-
quent and proper care does not only
“comply with the terms of the warranty,
but it will also keep your scooter looking
good, extend its life and optimize its’, ©,
performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly in-
“%& stalled. 5
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcasé В,
degreasing agent and a ”
with a
brush, but never apply such prod-
1
“greaser off with water.
Cleaning _
EC ECA1O7E4
e Avoid using strong acídic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to- remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
> the area off with water, immedi-
“ately dry it, and then apply a cor-
rosion protection spray.
® Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
ag any detergent residue using
- phe
SCOOTER CARE AND STORAGE
KC id, antifreeze or electrolyte.
. Do not use high-pressure wash-
- cleaners or hard sponges AS. the rain,
реф of water, as it is harmful
to plastic.parts.
Do not use’ any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or: abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
ers or steam-jet cleaners since
they cause water seepage and
deterioration | in the following ar-
eas: seals {of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, “instruments,
switches and lights}; breather
hoses and vents.
For scooters equipped: with a
windshield: Do not use strong
they will cause dulling or
scratching. Some cleaning com-
pourids for plastic may leave
scratches on the windshield.
Test the product on a small hid-
Te
tr
den part of the windshield té
make sure that it does not leave “®4, Clean the scooter with cold water
any marks, If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
hand then rinse thoroughly with. clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubbom dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
after riding in ti | |
n salt-spr
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride in
near the sea“or on
“salt-sprayed roads. on
к) я
TIP %
Salt sprayed on roads in the winter ay” +,
7-2
- remain well into spring.
“and a mild detergent after the en-
giñe has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the за все
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, sure to prevent
corrosion.
TIT
~ Avoid using any alkaline or strong acid
“eleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield with
a cloth er sponge dampened with a mild
detergent; and then wash it off thor-
oughly with’ water. For additional clean-
ing, use Yamaha Windshield Cleaner
or another high: quality windshield
cleaner. Some clearing compounds for
plastics may leave sératches on the
windshield. Before usingisuch clean-
ers, test an area of the windshield
which does not affect your visibility and
which cannot be easily recognized.
i 5,
a
Fe
SCOOTER CARE AND STORAGE
After éleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2 Use a chfome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring”: of stain-
less-steel exhaust systems can be
removed through polishing3=.
», 3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
“tection spray on all metal.
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by storiés, etc.
6. Wax all painted surfaces,
7. Let the scooter dry completely be-
fore storing or covering №.
e EVA 10043
№ TEN Ч
‘Contaminants on the brakes or tirés
can.cause loss of control.
* Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with “-
warm water and a mild deter-
gent.
Before operating the scooter
test its braking performance
and cornering behavior.
ECA10801
JE ri =;
in al
E E
Apply spray oil nf ‘wax spar-
ingly and make sure to wpe off
any excess.
Never apply oil or wax о ‘апу
rubber and plastic parts, but.
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products*to use.
Washing, rainy weather pr humid
climates can cause the headlight
lens to fog. Tuming the headlight
on for a short period of time will,
7-3
help remove the moisture from the
lens.
=;
Le
À
SCOOTER CARE AND STORAGE
EAL SE
Storage
Short-term
Always store your scooter in a cool, dry
“a, place and, if necessary, protect it
% , against dust with a porous cover. Be
“sure the engine and the exhaust sys-
tem are cool before covering the scoot-
er. © €
da ECA)
® Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
* To prevent corrosion, avoid
ue damp cellars, stables (because
Pa of the presence of ammonia)
%. and areas where strong chemi-
“с, cals are stored.
fm
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
#
LA
2.
3.
E
E
ty
5, from sparking, make sure to
РЁ up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
Perform the following steps to pro-
tect the cylinder; ‘piston rings, etc.
from corrosion. La
a. Remove the spark. plug cap
and spark plug. Rs
h. Pour a teaspoonful of engine oil
into the spark plug bore. ‘ kb
c. Install the spark plug cap onto
,, the spark plug, and then place
“tthe spark plug on the cylinder
head so that the electrodes are
grotinded. (This will limit spark-
ing dufing the next step.)
d. Turn the’ ‘engine over several
times with the. starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug,<and then
install the spark plug and the
spark plug cap. WARNINGLTo
prevent damage or injury
“ground the spark plug elec-
trodes while turning the en-
gine over. ews:
2, 74
4. Lubricate all control cables andthe
pivoting points of all levers and.
pedals as well as of the sidestand/ “+.
centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet’ ‘with а
plastic bag to prevent moisture
from entering it. =
7. Remove the battery and fully * %,
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 “C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the — see page
6-25.
TIP “a,
Make any necessary repairs before
storing the scooter. *
YE я a
A
=
+
A”
8-1
E By У, Lo
SPECIFICATIONS . к ‘
т т
Dimensions: Y с. Engine oil: Clufeh:
COR Jong: > Recommended brand: Clutch, type
8 kd 5.2 in) %, YAMALUBE Dry, éentrifugal automatic
gt va N a Type: Transmission:
oa п) Un SAE 10w-a0 — Primary reduction ratio:
ight: | я, Recommended engine oil grade: 1.000 &
e hs (43.7 in) Ч API service SG type or higher, JASO stan- Final drive: Ч
eight: “E dard MB ta
y с) hoe oe Gear
me mm (30.7 in) Tg Engine oil quantity; Secondary reduction ratio
elbase: a Periodic oil change: 10.668 (40 / 15 x 44 / 117.0
1280 mm (50.8 in) ty 0,85 L (0.90 US gt, 0.75 Imp.qt) Transmission type: “by
SR N 2e iranemiesion oil: >, V-belt automatic “a,
: 5, Chassis: к
М 900 по в SAE 10W-30 type SE motor oil “ong Frame type: ©
Vii: м Li) Quantity: “>. Backbone
pr ón € 0.13 L (0.14 US gt, 0.11 Imp.at} “Caster angle:
weight: ao Air filter: “27,00 °
122 kg (269 Ib) te, Air filter element: тай
ne 1 % Е Oil-coated paper element 90 mME3.5 in)
pe: uel: F s
Air cooled 4-stroke, SOHC 7, Recommended fuel: “ner a,
E amangement: To Unleaded gasoline only Tubeless — *.
ingle cylinder “a, Fuel tank capacity: Size: За
ape % 6.0 L (1.59 US gal, 1.32 Imp.gal) 120/70 - 12 511 2.
а И, Le ©. Fuel injection: Manufacturerimodel: — %,
%, Throttle body: KENDA / K761A +
Ö So X e oi (2.06 x 2.28 in) 6, ID mark: s Rear tire: “6,
pression ra > 559100 “o Type: 7
10.0 À. кр * %
Starting syêl ; Spark-plug(s): 5, Tubeless Ч
Electric e Manufacturer/madel: %, Size: |
PT а e DENSO / U22ESA-N #4, 130/70- 12 561
E i AE, к, Spark plug gap: Manutacturer/model:
mp de, 0.7-0.8 mm (0.028-0.031 in) KENDA / K761
“E
a
Wa
a
=
El
LA
A”
=
pi a o
E A
, ", SPECIFICATIONS
| ===
%. Loading: Specified brake fluid: © Bulb voltage, wattage x quantity:
“a Maximum load: DOT 4 “a Headlight:
e 155 kg (342 Ib) Rear brake: “Gs 12 Y, 60.0 W/55.0 W x 2
2? (Total weight of rider, passenger, cargo Type: % à Tail/brake light:
“p and accessories) Drum brake E 12 Y, 5.0 W/21.0 Wx1
Tire air er (measured on cold Operation: г E Front tum signal light:
tires): Left hand operation NA 12 Y, 10.0 W»x2
Lone Condition: Front suspension: 2 Rear tum signal light:
0-80 kg 18-198 lb) Type: %. 12V,10.0Wx2
Front: : a Telescopic fork “æ License plate light:
175 kPa (1 95 kgferné, 25 psi) Spring/shock absorber type: org © 8 WW > 1 (Use with T/L) i
Rear: Coil spring/oil damper ighting: >
200 kPa (2.00 hy 29 psi) Wheel travels | 12, 1.7 Wx 2
Loading condition: 78 mm (3.1 fa, High beam indicator light:
90 kg - maximum load Rear suspension: 12v, 17Wx1
3, Front: Type: % » Turn signal indicator light:
"o 200 kPa (2.00 kgtrem”, 29 psi) Unit swing “с 12 Y, 1.7 Wx1
A. Rear: Spring'shock absorber types, Engine trouble warning light:
VE, 225 kPa (2.25 kgliem?®, 33 psi) Coil springloll damper — % 12V, 1.7 Wx1
Front wheel: Wheel travel: Te Fuses:
Wheel type: 71 mm (2.8 in) To Main fuse:
Cast wheel Electrical system: ae 20.0 A
Rim Ignition system; E Headlight fuse:
J12 x2. 75 TCI 79, 100A
Rear wheel: = Charging system: “6. Signaling system fuse:
Wheel type: + AC magneto 4 15.0 A
Cast wheel "5, Battery: = Ignition fuse: :
Rim size: Ty Model: "5, 9 A
J12 X MT3.00 > VT7B-BS” Fuel injection system fuse:
Front brake: ю Voltage, e 10.0 À
: Туре: 12 М, 6.5 Ав * я
6, Single disc brake Headlight: E
“a Operation: Bulb type: ©.
By Hight hand operation Halogen bulb a
* B-2 ®
ds
gy
A
oh
fa
CONSUMER INFORMATION
LL =. west KEY IDENTIFICATION NUMBER:
Identification numbers
Record the vehicle identification num-
ber, engine serial number, model label
information, and the key identification
number in the spaces provided bel
These identification numbers are ne = > EAUS64
ed when registering the vehicle withthe “Vehicle identification number
authorities in your area and when or- E
dering spare parts from a Yamaha
Le)
dealer. KA
F7, ©,
VEHICLE IDENTIFICATION NUM- 1. Engine serial number
BER: VE, The engine serial number is stamped
За into the crankcase.
we 6, % ae
“a, Model label“
"чт
1. Vehicle identification number
ENGINE SERIAL NUMBER: LS т
“2. The vehicle identification number is
“stamped into the frame.
TIP.
e The Vehicle identification number is b,
MODEL LABELINFORMATION: used to identify your vehicle and may
| “y be used to register it with the licensing
О “tg, authority in your area.
3 %
=
€ 9-1 E
т ФР
E
А
ged
hg Ned
i
oo
SF кой
a и
La
Ea
va La
The model label is affixed to the frame I EBT" -
under the seat. (See page 3-8.) Record, Vehicle Emission Control Informa- = A
the information on this label in the tion label *
space provided. This information willbe — Gen a
needed when ordering spare parts from LE
a Yamaha dealer.
ALGAR
Key identification number /
O. 1. Vehicle Emission Control Information label €
>. The Vehicle Emission Control Informa-
“i. tion label is affixed at the location in the
“illustration. This label shows specifica- :
tions related to exhaust emissions as he
requifí federal law, state law and "a
1. Key identification number 9 eg by 7,
E Canada. +
The key identification number is
stamped into the key tag. Record this ea,
number in the space provided and use Te ©.
it for reference when ordering a new a 7
key. = y e L
o et “M
en За
Ti
Le
6. 5.
=#
Ca
CONSUMER INFORMATION 3 x
“hs e БАЦ
Reporting safety defects — +
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you води immediately
inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor” ‘Corporation,
U.S.A. If NHTSA receives similar complaintsy | it may open an investigation, and if it finds that a safety defect exists in a group
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual роте
between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety ‘Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-8153); go to http №
www. safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE, West Building, Washington, DC 20590.
You can also obtain ather information about motor vehicle: safety from http://www. safercar. gov.
Y
“ль Ч
r ы] da
= :
4
ae
=
o
rr
AF
el
и Че
Que | E
Y
19,
Von | % cons MER INFORMATION
CALIZA
Motorcycle noise regulation LY
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: iC
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inopérative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-
hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in ‘use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
"AMONG THOSE ACTS PRESUM EDTO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW". +:
Thess añ include tampering with the ong systems; i.e., modification, removal, etc. >
“| Exhaust system © y,
Es Muller Ул Ч
«Exhaust pipe E >,
%, » Silencer 4 |
9, Intake system
e = Air cleaner case e
e « Air cleaner element "a
a « Intake duct о,
%
Г’
+”
4
= El = a
A "e % 9.
ÈS, A a
CONSUMER INFORMATION __ >
% KK)
LL E. EBEN
Maintenance record = =
Copies of work orders and/or одре: for parts purchased and installed on your motorcycle will be required to document that
maintenance has been completed inaccordance with the emissions warranty. The chart below is printed Soy as a reminder
that maintenance work is required. It ismot acceptable proof of maintenance work.
Bac 18 =
Maintenance Dateof > Servicing dealer %
interval service Bl, Mileage name and address remato,
600 mi Че Eo
(1000 km) or 4 A
1 month_ "a .
2000 mi 5 Ls LT So
(4000 km) or 5; ca TL E
Emonths — Y Fa,
4000 mi ve “ба
(7000 km) or ЧБ E ia
12 months a An
5000 mi >, Ca,
18 months Ty “iy
8000 mi = »
(12000 km) or E €.
& +
5
24 months “Ta.
10000 mi =A L-
(16000 km) or © a
30 months E, Be
12000 mi %, “o
(19000 kmpor %, 6, E
36 months 7, ¿a 1
14000 mi “5 “E ©
(22000 km) or “+, by
mn Ve 3
16000 mi a, 6)
(25000 km) or 7 o,
a8 maith > | _
#
np"
hk
=,
Ca
e y
* Ú 9-5 : С
<i
À
da
"m I E om; e
=r Tar a .
A Y a CN
LA E By 9 L To
T5 i te + E
% ” CONSUMER INFORMATION —
Fi]
a a A] =
= E,
7; с
E Servicing dealer $ rks
Maintenance ©, Date of Mileage nr AI Br Ч Rema
interval « service de.
Ч "У
7 E,
18000 mi E, >,
(28000 km) or Or : 7,
54 months “a -
- F- 10
20000 mi 2 5
{31000 km) or “a, a
60 months A —
EL Be
o =
/ ds
hy SA
Foi És e a
E ra TA Fe
= x, ; Fri ES
E > o 1 L Ze
i “EL © La
= wt Ч
By CB
= = 5
LF =
e ©
a AA
O >
Va %,
hr Ga
Ca Ú
С. а an
Le o =F
e A
"yr E
Tan Lo я
"а т
т a,
La 3
rl
a 2
= L
“а и Ce
= i = =)
ar a“ hy 7
57) Y fy
“4 7, a Ja
5 a E ;
Ч и E
‘a 5 A
a E
yA A
“E а 6:
+ 7 “E
Le *.
О Bs.
“e 0,
E 9-6 ke
La Es iu
a
i
e
E
TE
CONSUMER INFC RMATION
a
"e
1 =
YAMAHA MOTOR CORPORATION, U.S.A. 2015 AND LATER MODEL SCOOTER LIMITED
WARRANTY .
WSIMGSS.
lANTY TRANSFER: To transfer any femaining
ity from the original purchaser to any subsëquent
iser, it is imperative that the machine be inspected
:gistered for warranty by an authorized Yamaha,
r dealer. In order for this warranty to remain in
this inspection and registration must take place
ten (10) days after transfer. A reasonable dealer-
ad fee may be charged tar he inspection.
¿JONS CONTROL SYSTEM WARRANTY
la Motor Corporation, U.S.A, also warrants to the
e purchaser and each subsequén! purchaser of
famaha scooter covered by this wéfranty with a
sement of 50cc or greater, that the” vehicle ls
ed, built, and equipped so as to conform, at the
f sale with all U.S. emissions standards applicable
time of manufacture and that it is free from defétts
erials and workmanship which would cause it notæ,
et these standards within the periods listed
liately below. Failures other than those resulting
jefects in material ar workmanship which arise
as a result of owner abuse and/or lack of proper
nance are not covered by "us warranty
A:
"о я
a
“i
2 :
a
UIAER WANMANIT Ur ANT AINU, CAFAC55ELÓUA
IMPLIED. ALL IMPLIED WARRANTIES OF
MERCHANTABILITY
PARTICULAR PURPOSE WHICH EXCEED THE
OBLIGATIONS AND TIME LIMITS STATED IN THIS
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA
MOTOR CORPORATION, U.S.A. AND EXCLUDED
| Ном THIS WARRANTY. o
De
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO’ YOU. ALSO
EXCLUDED FROM THIS WARRANTY ARE ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION Fe
EAUB TH
AND FITNESS FOR A“
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO “%
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
+ RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE
YAMAHA MOTOR CORPORATION, LSA.
PO. Box 6555
Cypress, Califérnia 90630
E.
g-7 * a
Po
оо
Po
ay
A
What costs are my responsibility, during the warranty persod?
The customer's responsibility includes al cosita ol normal mántemencs sérwvaed, mor:
Mare regaira. accident ame colmión demages, ar cl, 0 Miters, air fiber. agak
plugs. and brakes shoes Cha,
#
What are seme examples of “abnormal, staan, maglect, él abuse?
These terme are general and overlap aach otherih areas. Specific examples include
Runneng the machine out of oil, sustained Hi full -thwotile, operating the
machine with a broken or damaged par whath caubds anothers part tó fail, damage
e Tailuna due Lo Improper ar carelesa Tranagor aio and ar tie dos. | EOL Poio dere
EDECÍNC Questions on operation or mamnienance, please contact your dealer for advce
Ti
Does the aan Cor CANTA CORTE such as Cives' img) or att due lo
a tañune? -
Mo The waranty LE limited to repair of the mache ¡tae Зы,
2 Е
May | perform am or all of the recommended maintenance shown in Er
Manual instead of, having the dealer do them?
‘Yes, if you are a que Pg hanes ard loBow the procedures specitied in the ner’
and Service Manual do recommend, however, tha items reguiring specral tools
or equipment be done ty a Yamaha Riva dealer.
ME E
Will the warranty be void e Eanceld if 1 do not operate or maintain my new Riva
exactly as specified in the Owner's Manual?
Mo. The warranty on a new Riva € be “vosded” or “cancelled” However, if a
particular fallure i caused by opera or maintenance other then sa shawn in the
Dinars Menual. thet fallure may not'be covered under TEEN:
What responsibility dogs my dealer have
Each Yamaha Five desler la expécied te: 47
1. Completely set up every nes machine before pale.
à Enplain the opération, maintenance, and varra equirements bo your satisia
tion at the mé of sale and upon your request af later date
3, Esch Yamaha Ana. dealer ig held responsible bor: his Bet Service and
warranty repair work “Te
E
thes a Ary 7
ls the warranty transferable 16 second owners’
Yes. The remainder of The euxssting warranty can be transferred un The
uni has to'be inspected and re-regisiened by an authonzed Yamaha dealer far
the policy 10 tema effective Si,
ua i L
bi
To e
A
7,
%,
©
AA
a,
ir
Er
я 9-8
Ч = a a
“TT “Ta
CONSUMER INFORMATION —*
LS
if your machine requires waranty service vou masi o amy audhonzed
Yamaha Riva deslés vithen the contmental Uned States Be swe to bring
vour warranty regéstration card or other valid proof ol the ” date of
purchase If a question or problem arises regarding warranty, tigi contact
the owner of the deadershap. Since all marraniy maiters are handled at the
dealer level, this person is in the best postson to help vou I you au а
noi satisfied and require additional assistance, please write
YAMAHA MOTOR CORPORATION US A. E
CUSTOMER RELATIONS DEPARTMENT a
PO Box 6555 E
Cypress, Californias 90630 E
When comacting Yamaha Motor Comporation, ULSA. dont forget lo include 5
any important iMormation such as names, addresses. model. V.I'H (frame Lo
number), dales, and receipis. pT er
= on Fe L
CHANGE OF ADDRESS E
E 7
The federal government requetes each manufakturer of a motor vehicie to
maintain a complete, up-0-date Нал of all ford purchasers a the
possibility of a safety-related defect and recall. Tg kat is compsed from
the purchase registrations sent to Yamaha Motor Corporation US A. by the
selfing dealer at the time of your purchase Te,
M you should move alter you have purchased your naw mol piquse ac
y оное алое ouf para ar rc name,
V.LN (rame numbar, dealer Pua Gor chairs ring x Wd abr you
warranty card, your name and new maling address. Mail bo: “о
YAMAHA MOTOR CORPORATION, US A ih
PO Box 6555
Cypress. Cabfornia 9080
Apenas: Warranty Departement
This will ensure thal Yamaha Motor Corporation, USA has an up-1o-date
registration recoed in accordance with federal Law.
=. Le = a“
CONSUMER INFORMATION Ko *
К
e | FAJZETEZ
YAMAHA EXT ENDED SERVICE (Y.E.S.) LA
Keep your Yaltigha protected even after vour warranty « In addition, Travel and Recreation Interruption Protection
expires with genuing Yamaha Extended Service (Y.E.5.). (TRIP) is included at no extra cost. TRIP gives you up to
$250 reimbursement per occurrence for any reasonable
expenses you incur because yoút: Yamaha needs
covered service: replacement vehicle réfital, emergency
towing, phone calls, even food and lodging when you are
» YES. designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factdry; -backed coverage for extra
PEACE Of mind. e, away from home. This superb coverage goesiinto effect
« Y.E.S. is flexible. You choose he plan that's right for when you purchase Y.E.S., so it applies to any Warranty
: vou: 12 months, 24 months, 36 months or, on certain repairs as well as covered repairs during your un
a, models, even 48 months beyond your yarranty period. Y.E.S. plan period: =
о Y.E.S. is designed and administered2by the same * Y.E.B coverage is honored at any authorized Yamaha >,
“yamaha people who handle your warranty — and it dealer nationwide;
ws In the comprehensive coverage benefits. There
are mo mileage imitations, Coverage Isn't limited to
“moving, parts” or the "drive train” like many other plans.
» T.E.S. coverage 15° “transferable to a new owner if you
sell or trade-in. That cap. make your Yamaha much more
And YES. covers manufacturing defects just like the valuable! wy,
warranty. Se the sample contract at your Yamaha This excellent Y.E.S. plan covérage is only available to
dealer to seechow comforting uninterrupted factory- Yamaha owners like you, and only while your Yamaha is still
backed protection san be. within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
y Fa В ï
« You dont have to pay anything for covered repairs. you how easy It is to protect your investment with Yamaha
There's no deductiblé- to pay, and repairs aren
Extended Service.
“pro-rated.” You don't havésany “out-of-pocket” expenses Ч
: Da pit
for covered repairs. = € a
= i
dr a
E. © © €
5 и r Ea "бо.
=, [e Г. 15
oh (e LÏ Li
РЕ Ga ee
Pa, ¡A , Ay
fh a =
A ; N
dr %
E
"E Ca
[i] с
E -
E. “En
Ч. *
Le. Ty
7 9-9 e
=
À
e a a E
> * CONSUMER INFORMATION
We urge you ta act now. You'll get the excellent benefits of
TRIP coverage“ fight away, and you'll rest easy knowing
you'll have strong Tactory- -backed protection even after your
Yamaha Limited Warranty expires,
=
A special note: y
If visiting your dealer isnt cénvenient, contact Yamaha with
your Primary ID number (your. frame number). We'll be
happy to help you get the Y.E.5. coverage vou need.
a ;
Yamaha Service Marketing À a
_ PO. Box 6555 iy yy
“Cypress, CA 90630 Be Zn Re
Ei = =
1-1866)- YES-EXTD (1-866-937-3983) > a, 5,
e E da
CA TA, E
A EA
Fe | a
“= e
=, F
o 5
[2 Ч
DA Ty
© %,
E
J iF
чо y
"Ч. 4 Ч
"EL y
A A,
[Lx
©. "e
AL 3
a =
i 6 2 e
+ + e h o " г o
5 5 A 1
ar = у a
Pa La E 2h 72
Ч a he
Fa PA,
© ©,
E La.
“r г
du
E. “a
e Te
Ce ia
Ú 9-10 i Er
a u
o INDEX =
%
A
AG leration and deceleratio........———————— De
Air filter and V-belt case air filter
elemel 6-14
B “
Ballery............ Pda imi rp Bm 6-25
Brake fluid, charíging ...........—......——......6-22
Brake fluid level, ch ing... a ET
Brake laver, FONE... yeeros 35
Brake lever, rear SE A sos BD
Brake levers, lubricating... Gy................5-23
| Brake pads and shoes, checking res 6-20
FL. BIRR. cov arin minis vim pps na Bo. res 5-3
Pa С ci,
Py Cables, checking and lubricating .............6-22
ee i ve Ной 7-1
BIVHC CONVEr ...ve=m=. eee A a-7
Cemterstand and sidestand, TE and
be „6-23
Dimmer sah. SR PRES 3-4
Engine break- E IT A TA 5-3
Engine idling o RI Доли т 6-16
Engine mil, CT OTTER |
Engine serial number... Ms. TE 9-1
Engine stop switch... relly reno DA
ы Engine trouble warning light... бонд
+ F En
2106-13
6-19
A
A Final transmission oil … a
“4. Front brake lever free pay, checking. eta
“Eront fork, chacking … a BD
Fuel. „ана
Fuefagnsumption, ira for Te O
be
e.
Ш
+ ;
Pa t
E
EU O reroll #3 5
Fual tank cap... #5 Sale-riding points... 1-7
Fuses, replacing... 6-07 Salely defects, reporting ............—.— 9-3
H % Safety Information... 1-3
Handlebar switches ...3% Seal... par oo A
Aeadiight bulb, replacing ............. 6-27 T - Sidestand.. 3-10
Helmet holder ... не praia 38 “Spark plug, checking... Re IO
High beam irndiemor light... cas css BB Spécifications … cie a mouse
HOT aaa RE En 34 Speedometer unit. puni ocean pu pe O 3-3
| Starting off A pe О ЕСО 5-2
Identification numbers .. Se, 91 Starting gains... ae EEE 5-1
Ignition circuit cut- имет ся sis a 11 Start switch. 2a. o Я
Indicator lights and warming light... A 3-2 Steering, check. venerar E
K Te, Storage... RRR Re
Keyhole cover. a) aie 3.9 Storage compartment... EEE Penes o
Key identification number oi ori ens gz T
"a Tailbrake light... = …. 6-28
Labels, location.....…creseesiiy. 1-1 Throttle grip and cable, checking and
M Ч lubricating ... ius а 23
Main switchsteering took... Throttle grip free pay. . checldng.. 6-16
Maintenance and lubrication, pariodic....... 6-5" TIES iii B17
Maintenance, emission control system... 6-4 6 kit. LAE aR fr Led E a SE 6-2
Maintenance ECO res ‚9-5 EI ae
dec crea ACA 98 Tao Bhat ro 6-30
Model label: “ino decia 91 Turn Signal indicator light... nene A
N Turn signal light bulb, replacing .. … 6-28
Noise regulation... £ 9.4 Tum signal‘gwvitch … сана, Вей
pu di eb a A ; м a
P " "Sh
Valve clearance. „6-16
pur Se wd a 5 Vehicle E Eason Gir tomar м
& o abe Ce ei
y "CTO ea Be > ét Vehicle identification number. venais. 9-1
pci A W
Rear brake lever free play, adjusting, . “ik Warranty, extended......................... 9-9
+ )
SD
CR
"E
1,
Warranty, limited.................
Wheel bearings, checking .......................6-25 =
Wheels.
LF
q
D
-
LE -
5, %,
Te
т
A
+
i Be >
A Fa
4 a
e e
E > >”
SS | )
A rd &
æ У |
# г
4 4 F
8 6 *
: e 8
a g
5°
# S
A A
J «°
& s
e #
er ge"
# 2 se”
oF В
; e & р &
& - 6
47 © E
pe eu ”
= E
1
FE
5
LS,
®,
fe,
Ee
Lar
Le
Eu da
EF чи -
19 “= Lo
Lr 15 Lr
Bs 25
1
=
ый Кей
tr ©
и
a Eliana
For your best ownership experience, think Genuine Yamaha! L
Se
Genuine Yamaha Parts — Genuine Yamaha replacement parts are the exact same parts as the ones originally
equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for
aftermarket parts that may not provide full confidence and ds ca
“Genuine Yamaha Accessories — Yamaha only offers accessories that meet our high standards for quality and
performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right — right
out of the box. e. 6, O.
[o >, a, y >
Yamalube>— Take care of your Yamaha with, legendary Yamalube oils, lubricar: and care products. They're formulated
and approved by the toughest judges we knot: the Yamaha engineering teams that know your Yamaha from the inside
out. M, L
Genuine Yamaha Service Manuals — Get the samé factory manual for your vehicle that the technicians at your
authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them
directly through yamahapubs.com (for US consumers only}.
e 7
5
Genuine Yamaha products are available only from your Yamaha ‘dealer.
%, %
Find out more at: *
Fors consumers, please visit yamaha-motor.com Te.
For Canadian consumers, please visit yamaha- motor.ca e, LA
a pe ue) 7
Ye
%
E
“O,
Tk
=,
AM
%
©
E
“i
PRINTED IN TAÏWAN
2014.07-0.8 x 1 NKT
(Е)
%,
“
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement