DeVilbiss FinishLine HAR-680 Service Bulletin

SERVICE BULLETIN

HAR-680 80 CFM FILTER + REGULATOR

DESCRIPTION

These units are designed to remove water and dirt particles.

SPECIFICATIONS:

Air Inlet: 1/2 NPT (female)

Air Outlet HAF-580: 3/8 NPT (female)

Air Outlet HAR-680: 1/4 NPSM (male)

Air Capacity: 80 CFM filter

50 CFM regulator

Max. Pressure:

Max. Temp.:

Filter Size:

150 PSI

150° F

5 micron

INSTALLATION

1. Assemble unit (refer to Figure1).

2. Install with the air flowing into the top of the filter.

3. Install in a vertical position.

OPERATION

1. Turn the regulator’s handle clockwise to increase pressure.

2. To decrease pressure, turn the handle counterclockwise.

3. Relieve downstream pressure by triggering spray gun or tool.

FIGURE 1

Risk of personal injury.

Risk of property damage.

MAINTENANCE

1. Drain filter daily.

2. Depressurize before replacing filter element.

3. Replace element at least once per year.

RELEASE ALL AIR PRESSURE

BEFORE SERVICING.

SERVICE PARTS

See Parts List, page 2.

This product is specifically designed for compressed air service. Use with any other fluid (liquid or gas) is a misapplication. For example, use with or injection of certain hazardous gases in the system (such as oxygen or liquid petroleum gas) could be harmful to the unit or result in a combustible condition that may cause fire or explosion.

Manufacturer’s warranties are void in the event of misapplication and manufacturer assumes no responsibility for any resulting loss.

WARRANTY

This product is covered by DeVilbiss’ one year limited warranty. See

SB-1-000 which is available upon request.

Only on

HAR-680

SB-6-224-A (11/2016) 1 / 2

PARTS LIST

Ref.

No. Order No. Part No. Description

1 130100 HAR-520 Regulator

2

3

4

5

6

7

8

240160

192314

—

803641

*

*

VA-594

GA-375

—

HAF-47

*

*

KK-5088

Shut-Off Valve

Pressure Gauge

80 CFM Filter Unit

80 CFM Filter Element

Socket Head Screw,

1/4-20 x 3/4

Wingnut, 1/4-20

Regulator Kit

* Purchase Locally

FIGURE 2

Individual

Parts Req.

1

1

1

1

1

4

1

1

8

1

2

3

8

4

1

6

5

7

4

WARRANTY POLICY

DeVilbiss products are covered by Carlisle Fluid Technologies one year materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid Technologies, will void all warranties. For specific warranty information please contact the closest Carlisle Fluid Technologies location listed below.

DeVilbiss Automotive Refinishing is part of Carlisle Fluid Technologies, a global leader in innovative finishing technologies. For technical assistance or to locate an authorized distributor, contact one of our international sales and customer support locations.

USA/Canada www.autorefinishdevilbiss.com [email protected]

Toll Free Tel: 1-800-445-3988

Toll Free Fax: 1-800-445-6643

Mexico www.autorefinishdevilbiss.com.mx

Toll Free Tel: 1-888-835-6232 USA

Carlisle Fluid Technologies reserves the right to modify equipment specifications without prior notice.

DeVilbiss ® , Ransburg ® , MS ® , BGK ® , Binks ® , TEKNA ® , FinishLine

©2016 Carlisle Fluid Technologies, Inc. All rights reserved.

® , StartingLine ® , CamAir ® , CVi ® , PLUS ® , GTi ® , and PRi ® are registered trademarks of Carlisle Fluid Technologies, Inc.

2 / 2 SB-6-224-A (11/2016)