Elero RolTop Instruction
elero RolTop is an electromechanical tubular motor drive designed for use in façade engineering to drive electrically powered sun protection devices. It performs parallel axial movements and can be used for a variety of applications, including roller blinds, awnings, and shutters. The RolTop is easy to install and operate, and it comes with a variety of features to make it a versatile and reliable choice for your sun protection needs.
Advertisement
Advertisement
RolTop Roller Blind Drive
Table Of Contents
13 Operating and installation instructions
14 General for instructions
14.1 Standards and Directives
14.2 Intended use
14.3 Foreseeable misuse
14.4 Warranty and liability
14.5 Customer service of the manufacturer
15 Safety
15.1 General safety instructions
15.2 Layout of the safety guidelines
16 Product description
17 Assembly
17.1 Mechanical fastening
17.2 Electrical connection
17.3 Connection example, RolTop 230 V/50 Hz
17.4 Parallel connection
17.5 Commissioning
17.6 Setting the end positions and the relief
17.6.1 Relief function for the end position(s)
17.6.2 Relief function at the upper stop
17.6.3 Relief function at the lower stop
17.6.4 Changing / Deleting the limit positions and deleting the discharge function
17.6.5 Four variants of end position settings
5
5
17.6.6 Variant A: Upper and lower end position freely adjustable 5
17.6.7 Variant B: Fixed upper limit stop / lower end position freely adjustable 6
17.6.8 Variant C: Fixed upper and lower limit stop
17.6.9 Variant D: Upper end position freely adjustable, fixed lower limit stop
18 Troubleshooting
19 Repair
20 Repair
21 Manufacturer's address
22 Disassembly and disposal
23 Conformity Declaration
6
7
7
6
7
7
7
6
2
2
2
2
2
2
2
1
1
1
5
5
4
4
5
5
4
4
3
3
3
24 Technical data and dimensions
24.1 RevoLine S
24.2 RevoLine M
24.3 RevoLine s_onro M
24.4 RevoLine L
RolTop Roller Blind Drive
13 Operating and installation instructions
Please keep these operating instructions for later use, to be available throughout the life of the product!
The German manual is the original version.
All other documents represent the language translations of the original text.
All rights in the case of a patent, utility model or ornamental design registration are reserved.
14 General for instructions
The content structure is based on the life cycles of the electric motor drive (hereinafter referred to as "Product").
The manufacturer reserves the right to make changes to the Specifications stated in these Operating Instructions at any time. These may, in individual cases, be different from the respective product version, however the functional information will not undergo significant changes or become invalid. The current version of the Specifications may be requested from the manufacturer at any time. No claims may be asserted against the manufacturer as a result of the preceding sentence. Deviations from text or picture statements are possible and depend on the technical development, features, and accessories of the products. Deviating information on special versions will be explained by the manufacturer in the sales documentation. Other information shall remain unaffected by these provisions.
14.1 Standards and Directives
During the design process, the basic health and safety requirements of the applicable laws, Standards and Directives were complied with. The safety is confirmed by the declaration of conformity (see "Declaration of Conformity").
All safety information in these Operating Instructions refer to the laws and regulations currently applicable in Germany.
All instructions in the Operating Instructions shall be ob served without limitation and at any time. Beside the safety instructions contained in these Operating Instructions, the provisions for accident prevention, environmental protection and occupational safety, which are applicable for the operating site, must be observed. Provisions and Standards for the safety rating can be found in the Declaration of Conformity
138133301_EN_ 1020
9
10
11
7
8
Warranty and liability | Safety
14.2 Intended use
The product is intended for use in façade engineering to drive electrically powered sun protection devices.
The determining factor for the drive is the elero drive computation program wwww.elero.com/drive-calculation/
Further fields of application have to be arranged with the manufacturer, elero GmbH Antriebstechnik (see Address).
The operator will be solely responsible for damages resulting from improper use of the product. The manufacturer cannot be held liable for personal or material damages caused by misuse or procedural errors, and by improper operation and commissioning.
The product may be operated only by trained and authorized personnel under observance of all safety.
Only if used according to the specifications of these operat ing and installation instructions for the safe and proper use and safe operation of the product are guaranteed.
Intended use includes the observance and compliance with all safety instructions with regards to this operating manual and all applicable regulations, and professional associations of applicable laws for environmental protection. Intended use includes the observance of prescribed operating rules in these operating and installation instructions.
14.3 Foreseeable misuse
A use which deviates from the intended use stated by the manufacturer, elero GmbH Antriebstechnik (see "Address"), is deemed as foreseeable misuse.
14.4 Warranty and liability
Principally, the General Terms and Conditions of the manufacturer, elero GmbH Antriebstechnik (see "Address"), apply. The terms and conditions are part of the sales documents and handed over to the operator upon delivery. Liability claims for personal or material damages are excluded when they can be attributed to one or more of the following causes:
• Opening of the product by the customer
• Unintended use of the product
• Improper installation, commissioning, or operation of the product
• Structural modifications to the product without the written consent of the manufacturer
• Operation of the product with improperly installed con nections, defective safety devices or improperly installed safeguards
• Non-observance of the safety provisions and instructions of these Operating Instructions
• Non-compliance with the technical data
14.5 Customer service of the manufacturer
The product should only be repaired by the manufacturer in case of a failure. The address for sending to customer service, see the chapter "Address".
If you have not purchased the product directly from elero, please contact the supplier of the product.
15 Safety
15.1 General safety instructions
The general safety notes when using pipe drives can be found in the leaflet "Instructions on safety" that is enclosed with each drive"(leaflet item no. 138200001). These operat ing instructions contain all the safety instructions that must be observed in order prevent and eliminate hazards in the handling of the product in the individual life cycles. The safe operation of the product can only be ensured when all given safety instructions are observed.
15.2 Layout of the safety guidelines
The safety instructions in this document are identified by hazard signs and safety symbols and are designed according to the SAFE principle. They contain information on the nature and source of the danger of possible consequences and to prevent the danger.
The following table defines the representation and descrip tion of hazard levels with possible personal injury, as used in this manual.
Symbol Signal word
DANGER
Meaning
Warns before an accident, which will result if instructions are not followed, which can lead to life-threatening, irreversible injury or death.
WARNING Warns before an accident, which can happen if the instructions are not followed, which can lead to serious, possibly fatal, irreversible injury or death.
CAUTION Warns before an accident, which can happen if the instructions are not followed, which may lead to minor reversible injury.
Fig. 1 Notation of personal injury
The following table describes the icons used in these operating instructions that are used for imaging of the dangerous situation in connection with the symbol of the threat level.
Symbol Meaning
Danger of electric voltage, electric shock:
This symbol indicates a risk of electric shock.
Fig. 2 Notation-specific hazard
The following table defines the representation used in the operating instructions and description of situations where damage can occur to the product or refers to important facts, conditions, tips and information.
2 | EN © elero GmbH
Product description | Assembly (mechanical attachment)
Symbol Signal word
NOTE
Meaning
This symbol warns of a possible property damage.
Important: This symbol points out important facts and conditions as well as to additional information in these operating and installation instructions. It also refers to certain statements that give additional information or help you perform a task easily.
Fig. 3 Notation of property damage as well as additional information
The following example represents the basic structure of a safety warning:
SIGNAL WORD
Type and source of danger
Explanation of the type and source of the danger
► Measures to prevent the danger.
16 Product description
The RolTop is an electromechanical tubular motor drive. It performs parallel axial movements.
Commissioning of the RolTop with for setting different functions. elero assembly cable
Roller shutter with free ride (torque deactivation)
Relief function for the roller shutter (roller shutter protection).
Type s_onro with soft stop downwards
• The variant-dependent values of your RolTop can be removed from the type label.
• The different versions of the RolTop contain different types of brake systems depending on size and torque.
The result may yield different performance e.g. regarding access to end positions.
17 Assembly
CAUTION
Personal injury from hot surfaces.
Drive heats up during operation, the drive housing can be hot. Possible burning of the skin.
► Wear personal protective equipment (gloves).
Triggered by a possible material errors may occur or impact shock and injury due to a gearbox break, bud break or a clutch defect.
► Suitable materials are to be used for the construction as well as perform a sampling inspection by double load test according to DIN EN 60335-2-97.
Risk of injury due to impact or shock caused by not properly mounted or latched motor bearings. Hazards caused by insufficient stability or stability and stored energy (gravity).
►Selection of engine bearing torque specifications.
► Drive must be backed up with all attached backup devices.
© elero GmbH
► Check for proper latching on engine mounts and correct tightening torques.
WARNING
Danger of injury due to electric current.
Electric shock possible.
► Electrical work can only be performed by an authorized electrician.
Danger of injury due to electric current.
Hazardous possibly by parts that have become live in the error state.
► Electrical connection is described in the operating and installation instructions including cable bushing.
CAUTION
Risk of injury due to malfunctions due to improper installation.
Driven by winds and possibly destroyed parts of the application.
► For safe operation, the end positions must be set / programmed.
► Training program of the manufacturer for specialist companies.
NOTE
Loss of power supply, termination of machine parts and other malfunctions.
► For safe operation, no false mount must be made and the end position settings must be carried out during commissioning.
Damage to the RolTop due to moisture penetration.
►For devices with protection class IP44, the ends of all cables or connectors must be protected against the ingress of moisture. This measure must be implemented immediately after removal of the RolTop from the original packaging.
► The drive may only be installed so that it is not irrigated.
Important
In the delivery status (factory setting), the RolTop in com missioning mode.
► You have to set the end positions (see chapter 5.6).
17.1 Mechanical fastening
Important preliminary consideration:
The working space around the built-in drive is usually very small. Therefore, before the mechanical installation provide an overview of the implementation of the electrical connection (see Section 5.2) and make any necessary changes right away.
NOTE
Damage to the electrical wiring by squeezing or tensile loading.
► Route all electrical cables so that they are not subjected to crushing or tensile load.
► Note the bending radius of the cables (at least 50 mm).
► Lay the connection cable in a loop downwards to prevent water running into the drive.
Damage to the drive by the action of impact forces.
►Insert the drive into the shaft, never thrust the drive into the shaft or smash onto the drive!
► Never allow the drive to fall!
EN | 3
Assembly (Electrical connection) | Commissioning
Damage or destruction of the drive by drilling.
► Never drill into the drive!
Important
Attach the RolTop only at the appropriate fasteners.
Permanently installed control devices shall be clearly displayed.
• The curtain must be fastened to the winding shaft.
• The profile tube must have enough distance to the motor tube.
• Look for an axial clearance (1-2 mm).
Installation in profile tubes
Ⓐ Insert the drive with a suitable adapt er and traction ring into the profile tube.
Lay the motor cable protected in order to prevent damage by the driven component.
M
1~
Ⓑ Secure the counter bearings against axial displacement, e.g. screw shaft
Ⓒ spider or rivet.
Secure drive in axial storage!
Secure hanging on the shaft!
1 0 2
Only operate the drive horizontally, as intended, with the connection cable loading out from the sinde and out of the blind winding area.
Netz
230V/50Hz
PE
N
L
17.2 Electrical connection
4 | EN
Removal and insertion of the device plug
Delivery status Remove plug Insert plug
→
2
1
→
3
Fig. 4 Removal and insertion of the device plug
→
17.3 Connection example, RolTop 230 V/50 Hz
junction box power grid
230V/50Hz
PE
N
L
M
1~
1 0 2
WARNING
Danger to life due to faulty electrical connection.
Electric shock possible.
►
M
Before commissioning check the correct connection of the PE conductor.
NOTE
Damage to the RolTop by faulty electrical connection.
► Before commissioning check the correct connection of the PE conductor.
Damage or destruction of RolTop by the penetration of moisture. de volet nection of the cable ends or connector (cable bushing)
must also be carried out in accordance with protection class IP 44. reseau electrique
230V/50Hz
PE
N
Damage or destruction of RolTop for variants with 230 V
AC 1 due to faulty control.
►Switch with OFF setting (Dead man) for drives must be installed within sight of the RolTop, but away from any moving parts and amounting to about 1.5 m.
Important
For electric connection no transmission and retransmission of the access line or connector is required as a rule.
Depending upon used mounting plate and/or adapter plate it is necessary in particular with the RolTop Type S to remove this screwed plate before a cable exchange.
Connection only in free of tension status, in addition drive line without tension
1 Using a suitable screwdriver, press out the lock of the device connector to the line.
2 Disconnect the plug.
3 Insert connector until the latch engages.
© elero GmbH
(3)
(2)
(1)
(3)
(2)
(1)
Fig. 5 Circuit diagram RolTop 230 V / 50 Hz and wiring when used with Hirschmann plug STAS 3
Important
The motor control must be interlocked in up / down direction.
A reversing delay of at least 0,5 seconds must be ensured.
Important
17.5 Commissioning
Important
The drive is in the delivery in commissioning mode.
► You have to set the end positions with the bly cable. elero assem-
► Connection of the assembly cable is only admissible for commissioning of the drive and the setting processes.
:KLWHQHXWUDOFRQGXFWRU
%ODFN
5HG
*UHHQ
%ODX1HXWUDOOHLWHU
Fig. 6 Connection for cable assembly
*UQJHOE
► Switch on mains.
► You can now set the end positions with the bly cable. elero assem-
Commissioning | Setting the end positions and the relief
17.6 Setting the end positions and the relief
Important preliminary consideration:
Decide on a specific relief function before setting the end positions (different combination options according to the following statements):
This will save unnecessary setting effort!
Press the travel key until the drive signals the transition into the setting mode, by a short automatic stop. You can now program the end positions. After setting the two end positions, the setting mode is completed.
17.6.1 Relief function for the end position(s)
If an end position is set to stop, an additional relief for the roller shutter can be released.
Important
Activation of the relief function (in the versions B to D) takes place in one work step when the end positions are programmed (see chapter 5.6.7 to chapter 5.6.9)!
17.6.2 Relief function at the upper stop
For variant C (see chapter 5.6.7) and variant D (see chapter 5.6.8):
Activate relief function at the upper stop.
1 Push and hold the UP button ▲ from instruction ①
(chapters 5.6.7 and 5.6.8) and actuate the DOWN button ▼ with the assembly cable (at the same time).
Keep both buttons pushed until the roller shutter stops.
The relief function at the upper stop is activated.
17.6.3 Relief function at the lower stop
For version C (see chapter 5.6.8) and version D (see chapter 5.6.9):
Activate relief function at the lower stop
1 Push and hold the DOWNP button ▼ from instruction
③ (chapters 5.6.8 and 5.6.9) and actuate the UP button ▲ with the assembly cable (at the same time).
Keep both buttons pushed until the roller shutter stops.
The relief function at the lower stop is activated.
17.6.4 Changing / Deleting the limit positions and deleting the discharge function
A change or deletion of a single end position is not possible.
This is always done in pairs (upper and lower end position simultaneously).
By the deletion of the end positions and the adjustment of the optional discharge function is lost.
Important
The roller shutter is adjusted only after a complete and uninterrupted access and exit to the blind.
Changing / Deleting the end positions
1 From a middle blind position with the assembly cable, push and hold both direction buttons (▲ and ▼) at the same time until the drive briefly moves up and down.
The deletion of the setting of end position is completed.
The end positions can be programmed again.
17.6.5 Four variants of end position settings
Four different combinations of end position settings are possible. They must be selected sensibly according to the technical requirements of the roller shutter.
End position settings
(4 versions)
A Upper and lower end position freely adjustable
B Fixed upper limit stop / lower end position freely adjustable
C Fixed upper and lower limit stop possible with
T-strap, tapes, belt
T-strap, tapes, belt, limit plugs, angle bracket
Anti push-up device, stiff shaft connector, limit plugs, angle bracket
Anti push-up device D Upper end position freely adjustable, fixed lower limit stop
Fig. 7 Versions of the end position settings in the RolTop
17.6.6 Variant A: Upper and lower end position freely adjustable
Variant A:
Upper and lower end position freely adjustable
① From a middle blind position with the assembly cable, push the UP button ▲ until the roller shutter has reached the desired end position.
The drive starts, stops briefly and then moves on
(while the UP button ▲ is pushed).
Correction is possible with the buttons ▲ and ▼ .
② Press the AB button ▼ until the drive stops auto matically.
-
The upper end position has been set.
③ Press the AB button ▼ again until the roller shutter has reached the desired lower end stop.
The drive starts, stops briefly and then moves on
(while the AB button ▼ is pushed).
Correction is possible with the buttons ▲ and ▼ .
④ Press the AUF button ▲ until the drive stops automatically.
The lower end position has been set.
Setting of the end positions variant A is now complete.
Fig. 8 End position setting Variant A:
© elero GmbH EN | 5
Setting the end positions and the relief | Troubleshooting
17.6.7 Variant B: Fixed upper limit stop / lower end position freely adjustable
Variant B: Fixed upper limit stop / lower end position freely adjustable
① From a middle blind position with the assembly cable, push the UP button ▲ until the roller shutter has reached the desired end position (run to the upper stop).
The drive starts, stops briefly and then moves on
(while the UP button ▲ is pushed).
The drive switches off automatically when the upper limit stop is reached.
② Press the AB button ▼ until the drive stops auto matically.
The upper end position has been set.
Optional: Activation of the relief function for the upper stop; see chapter 5.6.2
③ Press the AB button ▼ again until the roller shutter has reached the desired lower end stop.
The drive starts, stops briefly and then moves on
(while the button is pushed).
Correction is possible with the buttons ▲ and ▼ .
④ Press the AUF button ▲ until the drive stops auto matically.
-
Setting of the end positions variant B is now complete.
Fig. 9 End position setting Variant B:
17.6.8 Variant C: Fixed upper and lower limit stop
Variant C: Fixed upper and lower limit stop
① From a middle blind position with the assembly cable, push the UP button ▲ until the roller shutter has reached the desired end position (run to the upper stop).
The drive starts, stops briefly and then moves on
(while the UP button ▲ is pushed).
The drive switches off automatically when the upper limit stop is reached.
② Press the AB button ▼ until the drive stops auto matically.
-
The upper end position has been set.
Optional: Activation of the relief function for the upper stop; see chapter 5.6.2
③ Press the AB button ▼ again until the roller shutter has reached the lower end stop (run to lower end stop).
The drive starts, stops briefly and then moves on
(while the DOWN button ▼ is pushed).
The drive switches off automatically when the lower limit stop is reached.
④ Press the AUF button ▲ until the drive stops auto matically.
-
The lower end position has been set.
Optional: Activation of the relief function for the lower stop; see chapter 5.6.3
Setting of the end positions variant C is now complete.
Fig. 10 End position setting Variant C:
17.6.9 Variant D: Upper end position freely adjustable, fixed lower limit stop
Variant D: Upper end position freely adjustable, fixed lower limit stop
① From a middle blind position with the assembly cable, push the UP button ▲ until the roller shutter has reached the desired end position.
The drive starts, stops briefly and then moves on
(while the button is pushed).
Correction is possible with the buttons ▲ and ▼ .
② Press the DOWN automatically.
button ▼ until the drive stops
The upper end position has been set.
③ Press the DOWN button ▼ again until the roller shutter has reached the lower end stop (run to lower end stop).
The drive starts, stops briefly and then moves on
(while the DOWN button ▼ is pushed).
The drive switches off automatically when the lower limit stop is reached.
④ Press the UP button ▲ until the drive stops automatically.
The lower end position has been set.
Optional: Activation of the relief function for the lower stop; see chapter 5.6.3
Setting of the end positions variant D is now complete.
Fig. 11 End position setting Variant D:
18 Troubleshooting
Problem /
Error
• Drive stops during travel
• Drive stops after a short time
• Drive runs only in one direction
Possible cause
• End positions are not set
• Drive is in setting mode
• End position programmed
• Sluggish shutter
• Connection error
Cure
Remedy
• Set end positions
• Set second end position
• Check smooth running of the roller shutter
• Check connection
• Drive not responding
• Drive does not learn any end positions
• No mains voltage
• Temperature limiter has tripped
• Random travel
• Travel to end position or limit stop too short
• Check mains voltage
• Allow drive to cool
• Delete end positions
Reset end positions
• Drive must run, stop briefly and run on
(while a button is pushed at the assembly cable).
Fig. 12 Error search at the RolTop
6 | EN © elero GmbH
Relief function | End position settings
19 Repair
The RolTop is maintenance free.
20 Repair
Please contact your dealer if you have any questions.
Please always provide the following information:
• Item number and name on the type plate
• Type of fault
• Previous and unusual events
• Surrounding circumstances
• Own assumption
21 Manufacturer's address
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlerbach
Deutschland / Germany
Phone: +49 7021 9539-0
Fax: +49 7021 9539-212 [email protected] www.elero.com
Please visit our website if you require a contact outside
Germany.
22 Disassembly and disposal
Dispose of the packaging according to current regulations.
Dispose the product after previous use in accordance with applicable regulations.
Environmental information
No unnecessary packaging was used. The packaging can be easily divided into three material types: Cardboard (box),
Styrofoam (padding) and polyethylene (bag, foam material protective foil).
The device is made up of materials that can be reused if it is disassembled by a specialist operation. Please observe the local provisions on disposal of packaging material and old devices.
Always expect additional danger that does not occur in operation during disassembly.
WARNING
Danger of injury due to electric current.
Electric shock possible.
► Physically disconnect power supply lines and discharge charged energy storage. Wait for at least 5 minutes after deactivation for the motor to cool down and the capacitors to lose their voltage.
► Use suitable, tested and stable climbing aids when performing disassembly work above body height.
► All work at the electrical system must only be performed by the staff described in the chapter "Safety instructions for electrical installation".
Scrapping
During the scrapping of the product, the international, national and regional-specific laws and regulations are to be complied with.
Please make sure to consider material recyclability, ease of dismantling, and separability of materials and components as well as environmental and health hazards during recycling and disposal.
CAUTION
Environmental damage at incorrect disposal
► Electronic scrap and electronic components are subject to the hazardous waste rules and must only be disposed of by approved specialist operation.
► Groups of materials such as plastics and metals of various kinds are sorted for recycling and disposal process.
Dispose electrical and electronic components
Disposal and recycling of electric and electronic components must comply with the applicable national laws and regulations.
23 Conformity Declaration
elero GmbH hereby declares that this product corresponds to the applicable directives. The complete declaration of conformity can be found under www.elero.com/downloads-service/downloads .
24 Technical data and dimensions
The indicated technical data are subject to tolerances (according to the respective applicable standards).
© elero GmbH EN | 7
Technical data and dimensions
24.1 RevoLine S
Baugröße / Typ
Roller shutter
Roller blind
Noiseless soft brake
Rated voltage [V]
Rated frequency [Hz]
Rated torque [Nm]
Rated speed [1/min]
Rated current [A]
Rated power consumption [W]
Shaft Ø [mm]
Limit switch range (turns)
Ingress protection (IP-Code)
Operation duration (min S2)
Length C [mm]
Length D [mm]
Length E [mm]
Weight [kg]
Temperature range [°C]
Protection class I
Conformity
Item number (round head / starhead)
S1,5/70 S3/30 S5/30
■
S5
■
S8
■
S10 FL S12 FL S12/11 FL
■ ■ ■
■
■
1 ~ 230
50
1,5
70
0,55
130
■
■
1 ~ 230
50
3
30
0,55
130
■
■
1 ~ 230
50
5
30
0,73
168
■
■
1 ~ 230
50
5
17
0,55
130
■
■
1 ~ 230
50
8
17
0,73
168
■
-
1 ~ 230
50
10
17
0,55
130
■
-
1 ~ 230
50
12
17
0,73
168
38
160
44
5
38
80
44
5
38
80
44
4
38
40
44
5
38
40
44
4
38
40
44
4
38
40
44
4
534
517
11
1,3
534
517
11
1,2
534
517
11
1,2
534
517
11
1,2
534
517
11
1,3
514
497
11
1,2
534
517
11
1,4
-20 ... 60 -20 ... 60 -20 ... 60 -20 ... 60 -20 ... 60 -20 ... 60 -20 ... 60
■
-
1 ~ 230
50
12
11
0,55
130
38
40
44
4
514
497
11
1,2
-20 ... 60
■ ■ ■ ■ ■ ■ ■ ■
■ | ■ ■ | ■ ■ | ■
302210001 302110001 302310001
■ | ■
302330001
■ | ■
302530001
■ | ■
308230001
■ | ■
308130001
■ | ■
30815001
D
C
E 33
D
C
8 | EN
E
Maße mit und ohne Funk
Baugröße Typ
Drehzahl
RolTop/VariEco S1,5 70/84
C
RolTop/VariEco S3 30/36
RolTop/VariEco S5 (17)/19/20
534
534
534
RolTop S7 30
RolTop/VariEco S8 (17)/-/-
RolTop/VariEco S12 (17)/19/20
RolTop/VariEco S10
534
534
514
D
517
517
517
517
517
497
E
11
11
11
11
11
11
© elero GmbH
33
Technical data and dimensions
24.2 RevoLine M
C
D
Type
Max. torque [Nm]
M6
6
M7/23
7
M10
10
M10-K
12
M12/23
20
M20
20
M30
30
M40
40
M50
50
Speed [1/min] 14 23 14 14 23 14 14 14 14
Operating voltage [V] 1 ~ 230 230 ... 240 1 ~ 230 1 ~ 230 1 ~ 230 1 ~ 230 1 ~ 230 1 ~ 230 1 ~ 230
50 50 50 50
33
50 50 50 50 50
Noiseless soft brake ■ ■ ■ ■ ■ ■ - - -
Current [A] 0,52 0,60 0,60 0,60 0,90 0,90 0,90 1,05 1,30
Power [W] 118 140 140 140 200 200 200 242 300
Shaft Ø [mm]
Ingress protection (IP-Code)
50
44
C
50
44
50
44
50
44
50
44
50
44
50
44
50
44
50
44
Llimit switch range (turns) 40 D 40 40 40 40 40 40 40 40
Operating mode (min S2) 5 5 5 4 4 4 4 5 4
Length C [mm] 446
C
466 466 391 526 526 516 546 546
Length D [mm] 429 449 449 374 509 509 499 529 529
Length E [mm]
D
(elero, round head, starhead) 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19 14 | 12 | 19
Weight [kg] 1,6 1,7 1,7 1,9 2,2 2,2 2,3 2,5
-20 ... 60 -20 ... 60 -20 ... 60
33
-20 ... 60 -20 ... 60 -20 ... 60 -20 ... 60
3,1
-20 ... 60
Conformity ,
Item number
(elero, round head, starhead)
■ ■ ■
■, ■
C
■, ■
343010001
393010001
D 342250001
382250001
C
■, ■
342210001
382210001
392210001
■
■, ■
33
341110001
381110001
■
■, ■
■
■, ■
■
■, ■
■
■, ■
342350001
382350001
342310001
382310001
392310001
342410001
382410001
392410001
29
392510001
D
■
■, ■
342610001
392610001
E
D
C
33
E
D
C
33
E 33
E
C
D
C
D
33
29
E
E
E
E
E
D
D
C
C
D
C
33
© elero GmbH
33
33
33
33
29
EN | 9
D
C
E
E
E 33
E
E
D
C
E 33
Baugröße Typ
RolTop M1,8/138 RH Neher 384493401
RolTop M1,8/138-868 RH Neher 384403406
D= C-17mm (halbe Kupplung)
120
120
Stator FE C
381
391
456
466
486
526
546
556
D
364
374
439
449
469
509
529
539
E elero=14
Motorrohr
Rol/Sun/Vari
339
RH=12
SH=19
349
414
424
444
484
504
514
Baugröße Typ
RolTop M1,8/138 RH Neher 384493401
RolTop M1,8/138-868 RH Neher 384403406
D= C-17mm (halbe Kupplung)
120
120
Stator FE
466
486
526
546
556
C
381
391
456
449
469
509
529
539
D
364
374
439
E elero=14
Motorrohr
Rol/Sun/Vari
339
RH=12
SH=19
349
414
424
444
484
504
514
Baugröße Typ
RolTop M1,8/138 RH Neher 384493401
RolTop M1,8/138-868 RH Neher 384403406
D= C-17mm (halbe Kupplung)
120
120
Stator FE C
381
391
456
466
486
526
546
556
D
364
374
439
449
469
509
529
539
E elero=14
Motorrohr
Rol/Sun/Vari
339
RH=12 349
SH=19 414
424
444
484
504
514
Technical data and dimensions
24.3 RevoLine s_onro M
Baugröße/Typ
Rated voltage (V)
Rated frequency (Hz)
Noiseless soft brake
Rated torque (Nm)
Rated speed (1/min)
Rated current (A)
Rated power consumption (W)
Shaft diameter (mm)
Protection class (IP)
Limit switch range (turns)
Operation duration (min S2)
Length C (mm)
Lenght D (mm)
Length E (mm) elero head
Length E (mm) star head
Weight (kg)
Operation environment temperature (°C)
RolTop s_onro
M10
RolTop s_onro
M20
RolTop s_onro
M30
RolTop s_onro
M40
230 - 240 1 ~ 230 1 ~ 230 1 ~ 230
RolTop s_onro
M50
1 ~ 230
44
40
5
466
449
14
19
50
•
10
14
0,60
140
50
1,9
– 20 bis +60
44
40
4
526
509
14
19
50
•
20
14
0,90
200
50
2,2
– 20 bis +60
44
40
4
516
499
14
19
50
–
30
14
0,90
200
50
2,3
– 20 bis +60
44
40
5
546
529
14
19
50
–
40
14
1,05
242
50
2,5
– 20 bis +60
44
40
4
546
529
14
19
50
–
50
14
1,30
300
50
3,1
– 20 bis +60
• | • • | • • | • • | • • | •
Confomity
Emission sound pressure level (dBA)
Protection class I
Plug-in connecting (m)
< 70
•
2,0
< 70
•
2,0
< 70
•
2,0
< 70
•
2,0
< 70
•
2,0
Item number elero head
Item number star head
34 221.5601
39 221.5601
34 231.5601
39 231.5601
34 241.5601
39 241.5601 39 251.5601 39 261.5601
10 | EN © elero GmbH
L60-80
L40 DC
(Rohrdurchmesser!)
Technical data and dimensions
24.4 RevoLine L
Build / Type
Rated voltage (V)
Rated frequency (Hz)
Noiseless soft brake
Application protection up and down and reversion on obstacle
Rated torque (Nm)
Rated speed (1/min)
Rated current (A)
Rated power consumption (W)
Shaft diameter (mm)
Protection class (IP)
Limit switch range (turns)
Operating duration (min S2)
Length C (mm)
Length D (mm)
Length E (mm)
Weight (kg)
Operating environment temperature
(°C)
Emission sound pressure level
(dBA)
Protection class I
Plug-in connecting cable (m)
RolTop
L60
1 ~ 230
RolTop
L80
50
–
•
60 80
14
1,9
430
2,0
470
63
44
40
4
575
558
14
3,3
– 20 bis +60
3,6
< 70
•
2,0
Item number 36 731.0001
36 741.0001
D
C
E= 14
D
C
E= 14
E= 16
D
C
© elero GmbH
33
33
33
EN | 11
Technical data and dimensions
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach [email protected]
www.elero.com
We reserve the right to make technical changes
Advertisement