User Manual
ENGLISH
F e d e r a l C o m m u n i c a t i o n s C o m m i s s i o n S t a t e m e n t ( C l a s s A)
NOTE- This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
ƒ Reorient or relocate the receiving antenna.
ƒ Increase the separation between the equipment and receiver.
ƒ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
ƒ Consult the dealer or an experienced radio/television technician for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class
B ITE limits. Such equipment should not be restricted in its sale but the following warning shall
be included in the instructions for use:
Warning - This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
COPYRIGHT
© 2012 AVer Information Inc. All rights reserved.
All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form,
or by any means without the prior written permission of AVer Information Inc. is prohibited. AVer
Information Inc. reserves the rights to modify its products, including their specifications and any
other information stated herein without notice. The official printout of any information shall
prevail should there be any discrepancy between the information contained herein and the
information contained in that printout. “AVer” is a trademark owned by AVer Information Inc.
Other trademarks used herein for description purpose only belong to each of their companies.
NOTICE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE
INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.
W AR N I N G
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT
MODIFICATION.
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER
HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE
WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL
AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT
WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING,
PLEASE CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE
OR THE SHOP WHERE YOU PURCHASED THE PRODUCT.
ENGLISH
Remote Control B a t t e r y S a f e t y I n f o r m a t i o n
-
Store batteries in any cool & dry place.
Do not dispose used batteries in domestic waste. Dispose batteries at special
collection points or return to stores if applies.
Remove the batteries if they are not in use for long period of time. Battery leakage
and corrosion can damage the remote control, dispose batteries safely.
Do not mix and use old and new batteries.
Do not mix and use different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
Do not dispose batteries in a fire.
Do not attempt to short circuit the battery terminals.
ENGLISH
Table of Contents
Package Contents ........................................................................... 1 Optional Accessories ..................................................................... 1 Get Familiar with the AVerVision M70 ........................................... 2 Right Panel ............................................................................................. 2 Rear Panel ............................................................................................. 3 Left Panel ............................................................................................... 3 Control Panel.......................................................................................... 4 Remote Control ...................................................................................... 5 Making the Connections ................................................................ 8 Set the TV-RGB Switch Setting .............................................................. 8 Connect to a Monitor or LCD/DLP Projector........................................... 8 Connect to a Monitor or LCD/DLP Projector with HDMI interface .......... 9 Connect to a TV ..................................................................................... 9 Connecting the Power .......................................................................... 10 Connect to a Computer ........................................................................ 10 Connect to a Computer via USB ........................................................... 11 Connect an External Microphone .......................................................... 11 Connect an Amplified Speaker ............................................................. 12 Connect to a Microscope ...................................................................... 12 Setting Up AVerVision M70 .......................................................... 13 Camera Head ....................................................................................... 13 Mechanical Arm .................................................................................... 14 Infrared Sensor..................................................................................... 14 Mounting the M70 on a Flat Surface .................................................... 15 Anti-glare Sheet.................................................................................... 15 External Memory Storage ..................................................................... 16 Insert an SD Car
d ........................................................................... 16 Card
Insert a USB Flash Driv
e ................................................................ 16 Drive
OSD MENU ..................................................................................... 17 Navigate the Menu and Submenu ........................................................ 18 Image ................................................................................................... 18 Brightness ....................................................................................... 18 Contrast .......................................................................................... 18 Mode ............................................................................................... 19 Effect............................................................................................... 19 Mirror .............................................................................................. 19 Advanced ........................................................................................ 19 Auto Image ..................................................................................... 20 Exposure ........................................................................................ 20 White Balance................................................................................. 20 Focus .............................................................................................. 20 Presentation ......................................................................................... 21 ENGLISH
Spotlight .......................................................................................... 21 Visor................................................................................................ 21 PIP .................................................................................................. 22 Split Screen .................................................................................... 22 Timer............................................................................................... 23 Setting .................................................................................................. 23 Capture ........................................................................................... 23 Resolution ....................................................................................... 23 Quality ............................................................................................ 23 Type ................................................................................................ 24 Interval ............................................................................................ 24 Recording ....................................................................................... 24 Storage ........................................................................................... 24 Format ............................................................................................ 24 USB to PC ...................................................................................... 25 Flicker ............................................................................................. 25 System ................................................................................................. 25 Language ........................................................................................ 25 Output Display ................................................................................ 25 Backup ............................................................................................ 26 Save Setting ................................................................................... 26 Recall Setting.................................................................................. 26 Information ...................................................................................... 26 Default ............................................................................................ 26 Playback ............................................................................................... 27 Slide Show ...................................................................................... 27 Interval ............................................................................................ 27 Slide Show Effect ............................................................................ 27 Current Storage .............................................................................. 27 Delete All ........................................................................................ 27 Annotation ............................................................................................ 28 Connecting a USB mouse or AP20T ............................................... 28 Using the Annotation Control Panel ................................................ 29 Using the AP20T Slide Switch and F button ................................... 29 Transfer Captured Images/Videos to a computer .............................. 30 Technical Specifications .............................................................. 30 Image .............................................................................................. 30 Optics ............................................................................................. 30 Power ............................................................................................. 30 Lighting ........................................................................................... 31 Input/Output .................................................................................... 31 Dimension ....................................................................................... 31 External Storage ............................................................................. 31 RS-232 Diagram Connection........................................................ 31 RS-232 Cable Specifications ........................................................ 32 RS-232 Transmission Specifications .......................................... 32 RS-232 Communication Format ........................................................... 32 ENGLISH
RS-232 Send Command Table ............................................................. 32 RS-232 Get Command Table ............................................................... 37 Troubleshooting ............................................................................ 38 Limited Warranty ........................................................................... 39 ENGLISH
Packa ge Contents
Make sure the following items are included in the package.
RS-232/CVBS Cable
Anti-glare Sheet
USB Cable
RGB Cable
AVerVision M70
Remote Control
(batteries included)
Power Adapter (12V, 2A)
* The power adapter will vary
depending on the standard
power outlet of the country
where it is sold.
Software & Manual CD
Carrying Bag
Optional Accessories
Microscope Adapter
34mm Rubber Coupler
Light Box
28mm Rubber Coupler
1
AVer AP20T
(Interactive Wireless Pen)
ENGLISH
G e t F a m i l i a r w i t h t h e AV e r V i s i o n M 7 0
(5)
(1)
(6)
(7)
(2)
(8)
(3)
(9)
(4)
(fig. 1.1)
Name
(1) Camera head
(2) Camera lens
(3) Control panel
(4) Built-in MIC
(5)
(6)
Arm
Left panel
(7)
(8)
IR sensor
Rear panel
(9)
Right panel
Function
Contain the camera sensor.
Focus the image in the camera.
Easy access to various functions.
Record audio when recording video clip. The recorded sound will be
in monophonic.
Extendable for viewing coverage.
Connections for LCD monitor using HDMI cable, microphone,
speaker, computer, SD card, and TV-RGB display output switch.
Receive remote control commands.
Connections for power, computer for RGB input display and LCD
monitor using RGB cable.
On/off switch for USB flash drive port and power button.
R ig ht Pa ne l
(2)
(1)
(3)
(fig. 1.2)
Name
(1) USB PC - USB Flash
Drive switch
(2)
(3)
USB Thumb Drive port
Power button
Function
Switch to right (►) for audio video recording directly to a
USB flash drive and left (◄) when connecting AVerVision
M70 to a computer using a USB cable.
Insert a USB flash drive for audio video recording storage.
Turn the unit on/standby mode.
2
ENGLISH
Rear Pa nel
(4)
(3)
(fig. 1.3)
(1)
(2)
Name
(1) Antitheft Slot
Function
Attach a Kensington compatible security lock or antitheft
device.
(2)
(3)
DC12V port
RGB INPUT port
(4)
RGB OUTPUT port
Connect the power adapter into this port.
Input the signal from a computer or other sources and pass it
through to the RGB OUT port only. Connect this port to the
RGB/VGA output port of a computer.
Connect the AVerVision M70 to any display device with RGB
cable
L eft P ane l
(5)
(6)
(4)
(3)
(2)
(7) (fig. 1.4)
(1)
Name
(1) Mini USB port
(2)
HDMI OUTPUT
(3)
MIC port
(4)
(5)
Speaker port
RS-232/CVBS port
(6)
TV-RGB switch
(7)
SD card slot
Function
Connect to a USB port of a computer with a USB cable and use
AVerVision M70 as a USB Camera or transfer the captured
images/videos either from the memory source to computer.
Output the video signal from the main system on an LCD monitor
with HDMI interface using HDMI cable.
Connect a 3.5mm plug microphone. The built-in mic will be
disabled when an external MIC is connected to this port.
Connect to an amplified speaker.
Connect the supplied RS-232/CVBS cable into this port. The RCA
jack outputs the video signal from the camera to a TV or video
equipment. The RS-232 jack is used to connect to computer serial
port or to any control panel or for centralized control if desire.
TV switch to output display video from RS232/CVBS (via RCA
connection), and RGB to RGB and HDMI OUTPUT ports.
Insert the SD card with the label facing up.
3
ENGLISH
Cont rol Panel
(1)
(7)
(2)
(3)
(8)
(9)
(4)
(10 )
(11)
(5)
(12 )
(6)
Name
(1) MENU
(2) RECORDING
(3)
CAP/DEL
(4)
PLAYBACK
(5)
FREEZE / STOP
(6)
(7)
Built-in MIC
CAMERA / PC
(8)
▲,▼,◄, & ►
(9)
ZOOM IN
(10) ZOOM OUT
(11) ENTER
(12) AUTO FOCUS
(13) LAMP
(13 ) (fig. 1.5)
Function
Open and exit the OSD menu.
Start/Stop audio & video recording. Audio and video recording can be
saved on a SD card or an USB Flash drive only. See External
Memory Storage.
- Capture picture in Camera mode. In continuous capture mode,
press this button again to stop.
- Delete the selected picture/video in Playback mode.
View & playback captured still images and audio video files.
- Pause or resume image display in Camera mode.
- Stop audio & video playback in Playback mode.
Record audio automatically when recording video clip.
Switch between Camera and Computer.
- Pan and zoom-in image (above digital zoom level) in both live and
playback mode.
- Select options in OSD menu.
- Use ▲&▼ to increase and decrease the video playback volume.
- Use ◄&► to play the video backward and forward.
- Move the Spotlight frame and Visor screen cover.
Increase the image magnification in camera and picture playback
mode.
Decrease the image magnification in camera and picture playback
mode.
- Make a selection in Playback mode and OSD menu.
- Start/Pause video playback.
Adjust the focus automatically.
Turn the overhead light on/off.
4
ENGLISH
Remote Cont rol
The remote control requires two (2) “AAA” size batteries (supplied), make sure batteries
are installed properly before use. You can access all the features of AVerVision M70 with
the remote.
(1)
(2)
(3)
(4)
(12)
(13)
(14)
(15)
(16)
(5)
(6)
(7)
(17)
(18)
(19)
(8)
(9)
Name
Function
(1)
POWER
Turn the unit on/standby.
(2)
CAMERA
(3)
RECORD
(4)
CAPTURE
(5)
VISOR
Camera mode displays the video signal
from the built-in camera.
Start/Stop audio & video recording. Video
recording can only be saved either in a
SD memory card or a USB flash drive.
Capture still image in Camera mode. In
continuous capture mode, press this
button again to stop.
Call the Visor submenu. Visor covers part
of the presentation screen and allow
presenter to reveal the material as desire.
In the Visor submenu, the following
options are available.
(20)
(10)
(21)
(11)
(22)
(23)
(fig. 1.6)
ON/OFF – select to run/cancel the Visor.
Press
to move to the next selection.
Shade – set the opacity level of the
covered area. The shaded area will
completely turns black when it is set to
level 100. Press
selection.
to move to the next
OK – press
for the setting to take
effect. If you select ON, upper part of the
presentation screen is slightly exposed.
Use the ▲,▼,◄, & ► buttons to reveal
more of the covered area; and OFF will
close the submenu.
(6)
ROTATE
(7)
MENU
5
To turn off Visor, press
again.
Rotate the image by 90° in Camera
mode and Playback mode.
Open and exit the OSD menu.
ENGLISH
(1)
(2)
(3)
(4)
Name
Function
(8)
- Pan and zoom-in image (above digital
zoom level) in both live and playback
mode.
- Select options in OSD menu.
- Use ▲&▼ to increase and decrease
the video playback volume.
- Use ◄&► to play the video backward
and forward.
Move the Spotlight frame and Visor
screen cover.
▲,▼,◄, & ►
(12)
(13)
(14)
(15)
(16)
(5)
(6)
(7)
(17)
(18)
(19)
(8)
-
(9)
(20)
(10)
(21)
(11)
(22)
(23)
(fig. 1.6)
(9)
AUTO
FOCUS
Adjust the focus automatically.
(10) ZOOM +/-
(11) ZOOM
RESET
(12) PLAYBACK
(13) PC 1/2
(14) FREEZE /
STOP
(15) SPOTLIGHT
- Increase/decrease the image
magnification in camera and picture
playback mode.
- Use to easily page up and page down
16-thumbnail picture preview.
Reset zoom level to 100%.
View the captured picture/video from the
memory in 16-thumbnail images.
PC mode displays the video signal from
the RGB INPUT port of M70.
- Freeze live images.
- Stop video playback.
Call the Spotlight submenu. Spotlight
overlays a box frame on the presentation
screen. You can adjust the box size and
move it around.
In the Spotlight submenu, the following
options are available.
ON/OFF – select to run/cancel the
Spotlight. Press
to move to the next
selection.
Shade – set the opacity level of the area
outside the box. The shaded area will
completely turns black when it is set to
to move to the next
level 100. Press
selection.
Color – select the Spotlight frame color.
6
ENGLISH
Name
Function
(15) SPOTLIGHT
(1)
(2)
(3)
(4)
(12)
(13)
(14)
(15)
(16)
(5)
(6)
(7)
(9)
(20)
(10)
(21)
(11)
(22)
(23)
to move to the next selection.
OK – press
for the setting to take
effect. If you select ON, the frame will
appear and blink, use the ▲,▼,◄, & ►
buttons to adjust the frame size and press
(17)
(18)
(19)
(8)
Press
to set the desired size; and OFF will
close the submenu.
(16) SPLIT
SCREEN
(17) MODE
(fig. 1.6)
(18) TIMER
(19)
(20) LAMP
(21) BRIGHTNES
S +/(22) DEFAULT
(23) DEL
again.
To turn off Spotlight, press
Divide the screen into two. One side
displays the live image from the built-in
camera and the other side displays 8thumbnail size picture/video from the
memory.
Select from 6 type of modes:
Sharp - adjust the contrast along the
edges making text appear more visible.
Graphics - adjust the gradient of image.
Motion - increase frame rate. Sufficient
lighting is required when using this
mode.
Microscope - automatically adjust
optical zoom for microscopic viewing.
Macro - set to view when object is only
5 –10cm away from the camera.
Infinite - set to view when subject is at
least 80cm away from the camera.
Call the Timer submenu. Select to
Start/Pause/Stop the timer countdown
and set the timer duration.
- Make a selection in Playback mode
and OSD menu.
- Play/Pause video playback.
Turn the overhead light on/off.
Adjust the brightness.
Reset to factory default setting.
Delete the selected picture/video in
Playback mode.
7
ENGLISH
Making the Connections
Before making the connection, make sure the power of all devices are turned off. If you
are not sure on where to connect, simply follow the illustrated connections below and also
refer to the user manual of the device you are connecting the AVerVision M70 with.
S e t t h e T V- R G B S w i t c h S e t t i n g
The TV-RGB switch determines the display output selection. Switch it to RGB (right) to
output signal using RGB/HDMI connection and TV (left) to output signal using RCA
connection. (see fig. 1.4 # 6)
Switch
AVerVision Port
Display Device Port
RGB OUTPUT
RGB INPUT
RGB
HDMI OUTPUT
HDMI INPUT
To
TV
RS232/CVBS
(use RS-232/CVBS cable)
VIDEO IN
Connect to a Monitor or LCD/DLP Pr ojector
Locate the RGB (VGA) input port of the graphics display device and connect it to RGB
OUTPUT port of AVerVision M70.
Make sure the TV/RGB switch is set to RGB.
RGB cable
LCD/DLP projector
CRT monitor
LCD monitor
8
ENGLISH
Connect to a Monitor or LCD/DLP Pr ojector with
HDMI interface
Locate the HDMI input port of the display device and connect it to HDMI OUTPUT port of
AVerVision M70.
Make sure the TV/RGB switch is set to RGB.
HDMI cable
HDMI monitor
Connect to a TV
Locate the VIDEO or SCART RGB (if applicable) input port of the TV or Video equipment
(i.e., VCR) to record your presentation and connect it to RCA jack of RS-232/CVBS cable.
RS-232/CVBS cable
INPUT
Projector
VIDEO
Te l e v i s i o n
SCART
RCA cable
RCA to SCART cable
(not supplied)
VCR
9
ENGLISH
C o n n e c t i n g t h e Pow e r
Connect the power adapter to a standard 100V~240V AC power outlet. The unit
automatically in standby mode once the power is connected. Press
Power adapter
to turn on.
Wall outlet
Connect to a Computer
Locate the RGB (VGA) output port of the computer or laptop and connect it to RGB INPUT
port of AVerVision M70. The video signal from the RGB INPUT port is streamed to RGB
OUTPUT port.
- To display computer image, press Camera/PC button on the control panel
or remote control to switch AVerVision M70 to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5)
to switch between the display modes. For different command, please refer
to your laptop manual.
Desktop
Laptop
RGB cable
10
ENGLISH
Connect to a Computer via USB
Locate the USB port of the computer or laptop and connect it to USB port of AVerVision
M70. This enables you to use AVerVision M70 as a USB Camera or to transfer the
captured pictures/videos from the memory and to computer. Also see “Transfer File from
AVerVision M70 to PC”.
Make sure the USB Flash Drive switch (see fig. 1.2 #1) is set to the left.
Desktop
USB cable
Laptop
Connect an Exter nal Microphone
Plug a 3.5mm mono microphone to port. The built-in microphone on the control panel
will be disabled when an external microphone is connected. The recorded audio will be in
monophonic sound.
Microphone
11
ENGLISH
C o n n e c t a n A m p l i f i e d S p e a ke r
Plug a 3.5mm plug amplified speaker to
supported.
port. Only the audio from the video playback is
We recommend connecting an amplified speaker to the Audio output port.
Take caution when using earphones. Adjust the volume down on the
remote to prevent hearing damage due to loudness.
Amplified Speaker
Connect to a Microscope
Connect the AVerVision M70 to a microscope enables you to examine microscopic objects
on a big screen.
1.
Change the image display mode to
Microscope. Press MENU > select
IMAGE tab > select MODE > select
(microscope) and press
.
2.
Aim the camera head at the farthest
point and press AUTO FOCUS.
3.
Adjust the focus of the microscope.
4.
Select the appropriate rubber coupler
size for the microscope eyepiece and
insert it in the microscope adapter.
12
ENGLISH
5.
Remove the microscope eyepiece
from the microscope and connect it to
the microscope adapter with the
rubber coupler inserted. Fasten the 3
bolts until the adapter secures the
eyepiece.
Microscope
adapter
Microscope
eyepiece
For the eyepiece, we suggest
using 15.5mm eye relief or higher.
6.
Attach the microscope adapter to the
AVerVision camera head. Then
connect it to the AVerVision and
microscope.
Microscope
S e t t i n g U p AV e r V i s i o n M 7 0
This section provides useful tips on how to adjust the AVerVision M70 to meet your needs.
Camera Head
The camera head can turn freely at 90° to the left and right and up and down.
90°
90°
90°
90°
If the camera head is in upright position, you can also press ROTATE on the remote
control twice to rotate the image in 180°.
13
ENGLISH
Mechanical Ar m
The mechanical arm design can extend for a full A4 paper viewing.
52mm (2.0 in)
195°
180°
Infrared Sensor
Aim the remote control at the infrared sensor to operate the unit.
14
ENGLISH
M o u n ti ng t h e M7 0 o n a F l at S u rfa c e
Measure and mark the horizontal of 75 mm and vertical of 70 mm from the center line
distance between the holes on the flat surface as describe in the illustration below. Use 4
pieces of M4.0 screws for 6 mm holes and secure the M70 on the flat surface.
Anti-glare Sheet
The anti-glare sheet is a special coated film that helps eliminate any
glare that maybe encountered while displaying very shiny objects or
glossy surfaces such as magazines and pictures. To use, simply
place the anti-glare sheet on top of the shiny document to reduce
reflected light.
15
ENGLISH
Exter nal Memor y Storage
AVerVision M70 supports both SD memory card and USB flash drive for more image
capture and audio & video recordings. AVerVision M70 can detect when there is an
external storage media and automatically switch to the last detected storage. If no
external storage is connected, all captured still images will be saved in the built-in memory.
Insert an SD Card
Insert the card with the contact facing down until it reaches the end. To remove the card,
push to eject and pull the card out. The supported SD card capacity is from 1GB to 32GB
(FAT).
SD Card
Insert a USB Flash Drive
Make sure to set the USB Flash Drive switch (see fig. 1.2 #1) to the right before inserting
a USB flash drive. AVerVision M70 can support USB flash drive from 2GB to 32GB (FAT).
USB Flash Drive
16
ENGLISH
OSD MENU
There are 4 tabs on the OSD menu: IMAGE, PRESENTATION, SETTING and SYSTEM.
In Playback mode, you can access PLAYBACK OSD menu to enable the Slide Show
feature and modify Slide Show interval and transition setting if desire.
For TV output, the RESOLUTION will be disabled in SETTING menu list.
IMAGE
PRESENTATION
SETTING
SYSTEM
ANNOTATION
PLAYBACK
17
ENGLISH
N avi g ate t h e Me n u a n d S u b m en u
1. Press MENU button on the remote or control
panel.
2. Press ► and ◄ to toggle between tabs
3. Press ▼ and ▲ to choose a selection in the
menu list.
to make a selection.
4. Press
5. Use ► and ◄ to adjust the setting or make a
selection.
6. Press
to enter submenu.
7. Press MENU to close the OSD menu.
Image
Menu Screen
Function
Brightness
Adjust brightness level manually between 0 and 63.
Contrast
Adjust the contrast level manually between 0 and 255
under bright and dark environments.
18
ENGLISH
Menu Screen
Function
Mode
Select from the various image display settings.
Sharp - adjust the contrast along the edges making
text appear more visible.
Graphics - adjust the gradient of image.
Motion - increase frame rate. Sufficient lighting is
required when using this mode.
Microscope - automatically adjust optical zoom for
microscopic viewing.
Macro - set to view when object is only 5 – 10 cm
away from the camera.
Infinite - set to view when subject is at least 80cm
away from the camera.
Effect
Convert the image into positive (true color), monochrome
(black and white) or negative.
Mirror
Select to flip the image in Camera mode.
Advanced
Select to set the Auto Image, Exposure, and White
Balance settings.
19
ENGLISH
Menu Screen
Function
Auto Image
Select ON or OFF to automatically adjust the white
balance and exposure setting, and correct the color and
exposure compensation.
Exposure
Select the exposure setting.
AUTO - automatically adjust the camera exposure and
the amount of light required.
MANUAL - manually adjust the exposure level. The
exposure can be adjusted up to 100.
White Balance
Select the White Balance setting for various light
conditions or color temperature.
AUTO - automatically adjust the white balance.
MANUAL - manually adjust the red and blue color level.
The color level can be adjusted up to 255.
Focus
Manually adjust the focus.
20
ENGLISH
Pr esentation
Menu Screen
Function
Spotlight
Spotlight overlays a frame on
the presentation screen. You
can move the Spotlight around
the presentation screen using
the ▲, ▼, ◄, & ► buttons.
Select Execute to call the
Spotlight submenu.
In the Spotlight submenu, the
following options are available.
ON/OFF – select to run/cancel
the Spotlight. Press
to
move to the next selection.
Shade – set the opacity level of the area outside the box.
The shaded area will completely turns black when it is set
to level 100. Press
to move to the next selection.
Color – select the Spotlight frame color. Press
move to the next selection.
to
OK – press
for the setting to take effect. If you
select ON, the frame will appear and blink, use the ▲, ▼,
◄, & ► buttons to adjust the frame size and press
to set the desired size; and OFF will close the submenu.
Visor
Visor covers the presentation
screen. The upper part of the
presentation screen is slightly
exposed. Use the ▲, ▼, ◄, & ►
buttons to reveal more of the
covered area. Select Execute to call
the Visor submenu.
21
ENGLISH
Menu Screen
Function
In the Visor submenu, the following options are available.
to
ON/OFF – select to run/cancel the Visor. Press
move to the next selection.
Shade – set the opacity level of the covered area. The
shaded area will completely turns black when it is set to
level 100. Press
to move to the next selection.
OK – press
for the setting to take effect. If you
select ON, upper part of the presentation screen is slightly
exposed. Use the ▲, ▼, ◄, & ► buttons to reveal more
of the covered area; and OFF will close the submenu.
PIP
Select the thumbnail playback screen location and show
the thumbnail playback screen at the corner of the
screen to recall the captured image from the memory in
Camera mode. Select OFF to cancel PIP.
Lower Left
Upper Left
Upper Right
Lower Right
Split Screen
Divide the screen into two parts. Half of the screen
displays the 8-thumbnail images and the other half
display the image from the AVerVision M70 camera.
Select the display location of the 8- thumbnail playback
images. Select OFF to cancel Split Screen.
Left
Right
Top
Below
22
ENGLISH
Menu Screen
Function
Timer
Start/Pause/Stop the timer and set the timer duration.
The timer automatically counts up after the count down
reaches zero to show the elapsed time. Even when you
switch between Playback, PC or Camera modes, the
timer will continue.
Setting
Menu Screen
Function
Capture
Select to set the capture resolution, quality, type and
interval settings.
Resolution
Select the capture size. In 5M setting, the capture
resolution size is 2560 X 1920.
Quality
Select the capture compression setting.
23
ENGLISH
Menu Screen
Function
Type
Select the capture type.
Single - capture one picture only.
Continuous - capture successive pictures.
Interval
Set the time interval for continuous capture. The length
can be set up to 600 sec (10 min).
Recording
Select the video recording compression setting.
Storage
Change the storage location. Audio & video recording
can only be saved in SD memory card or USB flash
drive.
Format
Format to delete all the data in the selected memory.
24
ENGLISH
Menu Screen
Function
USB to PC
Select the status of the AVerVision M70 when it is
connected to the computer via USB. Make sure the USB
switch on the left panel is set to
.
Camera - can be used as a computer webcam or with
our bundled software to record video and capture still
image.
Storage - transfer the captured pictures/videos from the
memory to computer hard disk.
Flicker
Select between 50Hz or 60Hz. Some display devices
cannot handle high refresh rates. The image will flicker a
couple of times as the output is switched to another
refresh rate.
System
Menu Screen
Function
Language
Change and select different language.
Output Display
Set the resolution to display the image on screen. This
selection will be disabled in TV output mode.
25
ENGLISH
Menu Screen
Function
Backup
Copy the image from the built-in memory to SD card or
USB flash drive.
Save Setting
Save current setting in the selected profile number. Only
effect, mode, brightness and contrast settings can be
saved.
Recall Setting
Restore the setting back to the selected profile number.
Information
Display the product information.
Default
Restore all the settings into original factory default
setting.
26
ENGLISH
P l a y b a ck
Menu Screen
Function
Slide Show
Display all captured still pictures in an automated slide
show. The video file will be skipped.
Interval
Set the interval before displaying the next picture. The
length can be set up to 100 sec.
Slide Show Effect
Select the slide show transition effect.
Slide image
Wipe right
Checker down
Split Vertical Out
Wipe down
Split Horizontal Out
Current Storage
Select the source of the images.
Delete All
Permanently delete all the data in selected memory
source. A Warning Message will appear. Select YES to
continue and NO to stop formatting the storage.
27
ENGLISH
Annotation
In single image playback mode or when the screen is frozen in camera mode, you can use
the annotation feature to overlay straight line or freeform line on the captured image or still
camera screen with the USB mouse or AP20T connected to the USB port of AVerVision
M70. It comes with the following selections: Color Palette, Line Thickness, Line, Freehand,
Capture, Eraser, and Hide/Show icons.
Annotation can only be supported in the
following resolution setting :
- 1024 x 768
- 1280 x 720
- 1280 x 1024
Connecting a USB mouse or AP20T
1. Set the USB switch on the left panel to
. AVerVision M70 will then detect the
USB mouse and the
LED on the
control panel will light up.
2. Connect the USB mouse cable or AP20T dongle to the USB slot of AVerVision M70.
USB Mouse
AP20T
USB Dongle
28
ENGLISH
Using the Annotation Control Panel
The annotation control panel appears on the upper left corner of the screen. A cursor will
appear on the screen. Move the cursor on the Annotation control panel selections and leftclick to select the features you want to use.
Name
Function
Color Palette
Select the line color.
Line Thickness
Select the thickness of the line.
Line
Select to draw a straight line.
Freehand
Capture
Eraser
Hide/Show
Select to draw freeform line.
Capture the image with the annotation and save it as a new
file.
Select to erase any part of the annotation that it comes in
contact with or delete all annotation.
Shrink or expand the annotation menu.
Using the AP20T Slide Switch and F button
The slide switch and F button of AP20T allow you to use it to freeze the screen when you
are in camera mode and zoom in and out the image when you are in playback and
camera mode. With the Point Focus feature, you can adjust the focus anywhere on the
screen by simply pressing the pen tip on a flat surface.
(4)
(1)
Name
Function
(1) Slide Up
Increase the magnification.
(2) Slide Down
Decrease the magnification
Freeze the screen in camera mode and
turn on Annotation.
(3) F
(2)
(3)
Press to adjust the camera focus on
the point where the cursor is located.
(4) Pen tip
29
ENGLISH
Transfer Captured Images/Videos to a computer
This enables you to transfer the captured image from the built-in memory or SD to a
computer.
The instruction below MUST be read and followed BEFORE connecting
the USB cable.
1. Make sure to set the USB switch to
to detect AVerVision M70.
for the computer
2. MUST set the USB to PC as STORAGE before
connecting the USB cable.
3. When “Mass Storage Start…” appears at the lower
right corner of the presentation screen, you may now
connect the USB cable.
4. Upon connecting the USB cable, the system automatically detects the new removable
disk. You can now transfer the captured image(s) from the UUM70 built-in
memoryUU to the computer hard disk.
Te c h n i c a l S p e c i f i c a t i o n s
Image
Sensor
1/3.2” CMOS
Pixel Count
5 megapixels
Frame Rate
30 fps (max.)
White Balance
Auto / Manual
Exposure
Auto / Manual
Image mode
Sharp / Graphics / Motion / Microscope / Macro / Infinite
Effect
Color / B/W / Negative / Mirror / Rotate / Freeze
RGB output
1920x1080, 1600x1200, 1280x1024, 1280x720, 1024x768
HDMI output
HD 1080p; HD 720p
Image Capture
240 Frames(XGA) ; 80 Frames(5M Pixel)
Optics
Focusing
Auto / Manual
Shooting Area
420mm x 315mm
Zooming
Total zoom 192X ( 12X Optical + 2X AVERZOOM™ +8X
Digital Zoom)
Power
Power Source
DC 12V, 100-240V, 50-60Hz
Consumption
16.8 Watts (lamp off); 18 Watts (lamp on)
30
ENGLISH
Lighting
Lamp Type
LED light
Input/Output
RGB Input
15-Pins D-sub (VGA)
RGB Output
15-Pins D-sub (VGA)
HDMI Output
HDMI
CVBS/RS-232
Mini-DIN Jack (use CVBS/RS-232 Adapter cable)
Composite Video
RCA Jack
USB
USB2.0
DC 12V Input
Power Jack
MIC
Phone Jack
Speaker
Phone Jack
Dimension
Operating
452mm x 182mm x 504mm (+/-2mm include rubber foot)
Folded
367mm x 182mm x 63mm (+/-2mm include rubber foot)
Weight
2.1 kg (about 4.629 lbs)
External Storage
Secure Digital (SD)
Max 32GB (FAT)
USB Flash Drive
Max 32GB (FAT)
RS-232 Diagram Connection
AVerVision M70 can be controlled using a computer or any centralized control panel
through RS-232 connection.
RS-232/CVBS cable
Desktop
RS-232 cable
(not supplied)
Laptop
31
ENGLISH
R S - 2 3 2 C a b l e S p e c i f ic at i o n s
Make sure the RS-232 cable matches the cable specification design.
PC COM Port
DSUB-9P (Female)
5 4 3 2 1
9 8 7 6
CD 1
1
RXD 2
2 TXD
TXD 3
3 RXD
DTR 4
4
5 SG
SG 5
DSR 6
6
RTS 7
7
CTS 8
8
RI (CI) 9
9
AVerVision RS-232 Port
DSUB-9P (Female)
5 4 3 2 1
9 8 7 6
R S - 2 3 2 Tr a n s m i s s i o n S p e c i f i c a t i o n s
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
:1 bit
:8 bit
:1 bit
:None
:None
:9600bps
Start bit
Data bit
Stop bit
Parity bit
X parameter
Baud rate (Communication speed)
R S - 2 3 2 C o m m u n i c a t i o n Fo r m a t
Send Device Code(1 Byte)
Type Code(1 Byte)
DataLength Code(1 Byte)
Data Code(1 Byte)
Data Code(2 Byte)
Data Code(3 Byte)
Receive Device Code(1 Byte)
CheckSum Code(1 Byte)
Format
Example
: 0x52
: 0x0B
: 0x03
: See the Command Table for reference.
: See the Command Table for reference.
: See the Command Table for reference.
: 0x53
: See the Command Table for reference.
: Start + Type + DataLength + Data + CheckSum
: 0x52 + 0x0B + 0x03+ 0x3 + 0x01 + 0x00 + 0x00 + 0x53 +
0x5A (Command Power)
R S - 2 3 2 S e n d C o m m a n d Ta b l e
Send Format︰0x52 + 0x0B + 0x03 + Data[0] + Data[1] + Data[2] + 0x53 + CheckSum
Receive Format︰0x53 + 0x00 + 0x02+ *2 + *3 + 0x52 + CheckSum
*1 :CheckSum = 0x0B xor 0x03 xor Data[0] xor Data[1] xor Data[2] xor 0x53
*2 :Receive data ok : 0x0B, ID error: 0x01, CheckSum error: 0x02, Not Command : 0x03,
Function fail = 0x04
*3 :Data[0], Return 0x00 if error
32
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum
POWER OFF 0x01 0x00 0x00 0x5A POWER ON 0x01 0x01 0x00 0x5B CAMERA MODE 0x02 0x00 0x00 0x59 PLAYBACK MODE 0x03 0x00 0x00 0x58 PC‐1 PASS THROUGH 0x04 0x00 0x00 0x5F IMAGE CAPTURE TYPE: SINGLE 0x05 0x00 0x00 0x5E IMAGE CAPTURE TYPE: CONTINUOUS 0x05 0x01 0x00 0x5F CONT. CAPTURE INTERVAL + 0x06 0x00 0x00 0x5D CONT. CAPTURE INTERVAL ‐ 0x06 0x01 0x00 0x5C NORMAL IMAGE CAPTURE 0x07 0x00 0x00 0x5C 3M/5M IMAGE CAPTURE 0x07 0x01 0x00 0x5D TIMER START 0x08 0x00 0x00 0x53 TIMER PAUSE 0x08 0x01 0x00 0x52 TIMER STOP 0x08 0x02 0x00 0x51 0x03 VALUE[ 1 ~ 120 ] *1 TIMER SET TIME 0x08 PREVIEW MODE: SHARP 0x0A 0x00 0x00 0x51 PREVIEW MODE: GRAPHIC 0x0A 0x01 0x00 0x50 PREVIEW MODE: MOTION 0x0A 0x02 0x00 0x53 PREVIEW MODE: MICROSCOPE 0x0A 0x03 0x00 0x52 PREVIEW MODE: MACRO 0x0A 0x04 0x00 0x55 PREVIEW MODE: INFINITE 0x0A 0x05 0x00 0x54 PREVIEW MODE CAPTURE 0x0B 0x00 0x00 0x50 PLAYBACK DELETE 0x0C 0x00 0x00 0x57 PLAYBACK FULL SCREEN 0x0D 0x00 0x00 0x56 MIRROR OFF 0x0E 0x00 0x00 0x55 MIRROR ON 0x0E 0x01 0x00 0x54 ROTATE 0 0x0F 0x00 0x00 0x54 ROTATE 90 0x0F 0x01 0x00 0x55 ROTATE 180 0x0F 0x02 0x00 0x56 ROTATE 270 0x0F 0x03 0x00 0x57 33
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum
EFFECT: COLOR 0x10 0x00 0x00 0x4B EFFECT: B/W 0x10 0x01 0x00 0x4A EFFECT: NEGATIVE 0x10 0x02 0x00 0x49 CONTRAST INCREASE 0x11 0x00 0x00 0x4A CONTRAST DECREASE 0x11 0x01 0x00 0x4B *1 CONTRAST VALUE 0x11 0x02 VALUE[ 0 ~ 255 ] BRIGHTNESS INCREASE 0x12 0x00 0x00 0x49 BRIGHTNESS DECREASE 0x12 0x01 0x00 0x48 BRIGHTNESS VALUE 0x12 0x02 VALUE[ 0 ~ 63 ] *1 EXPOSURE: AUTO 0x13 0x00 0x00 0x48 EXPOSURE: MANUAL 0x13 0x01 0x00 0x49 EXPOSURE MANUAL INCREASE 0x14 0x00 0x00 0x4F EXPOSURE MANUAL DECREASE 0x14 0x01 0x00 0x4E WHITE BALANCE: AUTO 0x15 0x00 0x00 0x4E WHITE BALANCE: MANUAL 0x15 0x01 0x00 0x4F WHITE BALANCE BLUE INCREASE 0x16 0x00 0x00 0x4D WHITE BALANCE BLUE DECREASE 0x16 0x01 0x00 0x4C WHITE BALANCE RED INCREASE 0x17 0x00 0x00 0x4C WHITE BALANCE RED DECREASE 0x17 0x01 0x00 0x4D FLICKER: 50Hz 0x18 0x00 0x00 0x43 FLICKER: 60Hz 0x18 0x01 0x00 0x42 SPOTLIGHT: OFF 0x19 0x00 0x00 0x42 SPOTLIGHT: ON 0x19 0x01 0x00 0x43 SPOTLIGHT SHADE: 0% DARK 0x1A 0x00 0x00 0x41 SPOTLIGHT SHADE: 50% DARK 0x1A 0x01 0x00 0x40 SPOTLIGHT SHADE: 100% DARK 0x1A 0x02 0x00 0x43 SPOTLIGHT COLOR: RED 0x1B 0x00 0x00 0x40 SPOTLIGHT COLOR: GREEN 0x1B 0x01 0x00 0x41 SPOTLIGHT COLOR: BLUE 0x1B 0x02 0x00 0x42 SPOTLIGHT RESIZE 0x1C 0x00 0x00 0x47 34
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum
VISOR: OFF 0x1D 0x00 0x00 0x46 VISOR: ON 0x1D 0x01 0x00 0x47 VISOR SHADE: 50% DARK 0x1E 0x00 0x00 0x45 VISOR SHADE: 100% DARK 0x1E 0x01 0x00 0x44 PIP: OFF 0x1F 0x00 0x00 0x44 PIP: ON 0x1F 0x01 0x00 0x45 PIP POSITION: BOTTOM LEFT 0x20 0x00 0x00 0x7B PIP POSITION: TOP LEFT 0x20 0x01 0x00 0x7A PIP POSITION: TOP RIGHT 0x20 0x02 0x00 0x79 PIP POSITION: BOTTOM RIGHT 0x20 0x03 0x00 0x78 SPLITSCREEN: OFF 0x21 0x00 0x00 0x7A SPLITSCREEN: ON 0x21 0x01 0x00 0x7B SPLITSCREEN DIR: UPPER SCREEN 0x22 0x00 0x00 0x79 SPLITSCREEN DIR: LOWER SCREEN 0x22 0x01 0x00 0x78 SPLITSCREEN DIR: LEFT SCREEN 0x22 0x02 0x00 0x7B SPLITSCREEN DIR: RIGHT SCREEN 0x22 0x03 0x00 0x7A RECORDING: OFF 0x23 0x00 0x00 0x78 RECORDING: ON 0x23 0x01 0x00 0x79 MOVIE FAST REWIND 0x25 0x00 0x00 0x7E MOVIE FAST FORWARD 0x25 0x01 0x00 0x7F MOVIE VOL INC 0x26 0x00 0x00 0x7D MOVIE VOL DEC 0x26 0x01 0x00 0x7C RECORDING QUALITY: NORMAL 0x27 0x00 0x00 0x7C RECORDING QUALITY: HIGH 0x27 0x01 0x00 0x7D STORAGE: EMBEDDED 0x28 0x00 0x00 0x73 STORAGE: SD CARD 0x28 0x01 0x00 0x72 STORAGE: THUMB DRIVE 0x28 0x02 0x00 0x71 FORMAT: EMBEDDED 0x29 0x00 0x00 0x72 FORMAT: SD CARD 0x29 0x01 0x00 0x73 FORMAT: THUMB DRIVE 0x29 0x02 0x00 0x70 35
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum
OUTPUT RESOLUTION: 1024x768 0x2F 0x01 0x00 0x75 OUTPUT RESOLUTION: 1280x720 0x2F 0x02 0x00 0x76 OUTPUT RESOLUTION: 1920x1080 0x2F 0x03 0x00 0x77 OUTPUT RESOLUTION: 1280x1024 0x2F 0x04 0x00 0x70 OUTPUT RESOLUTION: 1600x1200 0x2F 0x05 0x00 0x71 USB CONNECT: USB CAMERA 0x30 0x00 0x00 0x6B USB CONNECT: MASS STORAGE 0x30 0x01 0x00 0x6A BACKUP TO SD CARD 0x31 0x00 0x00 0x6A BACKUP TO THUMBDRIVE 0x31 0x01 0x00 0x6B PROFILE SAVE: PROFILE 1 0x32 0x00 0x00 0x69 PROFILE SAVE: PROFILE 2 0x32 0x01 0x00 0x68 PROFILE SAVE: PROFILE 3 0x32 0x02 0x00 0x6B PROFILE RECALL: PROFILE 1 0x33 0x00 0x00 0x68 PROFILE RECALL: PROFILE 2 0x33 0x01 0x00 0x69 PROFILE RECALL: PROFILE 3 0x33 0x02 0x00 0x6A SLIDESHOW: OFF 0x34 0x00 0x00 0x6F SLIDESHOW: ON 0x34 0x01 0x00 0x6E SLIDESHOW EFFECT: EFFECT 0 0x35 0x00 0x00 0x6E SLIDESHOW EFFECT: EFFECT 1 0x35 0x01 0x00 0x6F SLIDESHOW EFFECT: EFFECT 2 0x35 0x02 0x00 0x6C SLIDESHOW EFFECT: EFFECT 3 0x35 0x03 0x00 0x6D SLIDESHOW EFFECT: EFFECT 4 0x35 0x04 0x00 0x6A SLIDESHOW EFFECT: EFFECT 5 0x35 0x05 0x00 0x6B AUTO IMAGE:OFF 0x36 0x00 0x00 0x6D AUTO IMAGE:ON 0x36 0x01 0x00 0x6C CAPTURE QUALITY: NORMAL 0x37 0x00 0x00 0x6C CAPTURE QUALITY: HIGH 0x37 0x01 0x00 0x6D CAPTURE QUALITY: FINEST 0x37 0x02 0x00 0x6E AUTO FOCUS 0x40 0x00 0x00 0x1B MENU 0x41 0x00 0x00 0x1A 36
ENGLISH
Function
Data[0]
Data[1]
Data[2]
CheckSum
ARROW ‐ DOWN 0x42 0x00 0x00 0x19 ARROW ‐ UP 0x42 0x01 0x00 0x18 ARROW ‐ LEFT 0x42 0x02 0x00 0x1B ARROW ‐ RIGHT 0x42 0x03 0x00 0x1A ENTER 0x43 0x00 0x00 0x18 FREEZE 0x44 0x00 0x00 0x1F DEFAULT 0x45 0x00 0x00 0x1E ZOOM ‐ 0x46 0x00 0x00 0x1D ZOOM + 0x46 0x01 0x00 0x1C ZOOM RESET 0x47 0x00 0x00 0x1C NEAR 0x48 0x00 0x00 0x13 FAR 0x48 0x01 0x00 0x12 LAMP OFF 0x49 0x00 0x00 0x12 LAMP ON 0x49 0x01 0x00 0x13 R S - 2 3 2 G e t C o m m a n d Ta b l e
Send Format︰0x52 + 0x0A + 0x01 + Data[0] + 0x53 + CheckSum
Receive Format︰0x53 + 0x0C + 0x01 + ReData[0] + 0x53 + ReCheckSum
*1 :ReCheckSum = 0x0C xor 0x01 xor ReData[0] xor 0x52
Data[0]
CheckSum
Code
RED VALUE 0x02 0x5A VALUE[ 0 ~ 255 ] BLUE VALUE 0x03 0x5B VALUE[ 0 ~ 255 ] POWER STATUS 0x04 0x5C 0 : OFF 1: ON LAMP STATUS 0x05 0x5D 0 : OFF 1: ON DISPLAY STATUS 0x06 0x5E 0: CAMERA MODE 1: PLAYBACK MODE 2: PC‐1 PASS THROUGH VIDEO OUTPUT STATUS 0x07 0x5F 0: VGA 1: TV FREEZE STATUS 0x08 0x50 0 : OFF 1: ON BRIGHTNESS VALUE 0x0A 0x52 VALUE[ 0 ~ 63 ] CONTRAST VALUE 0x0B 0x53 VALUE[ 0 ~ 255 ] Function
37
ReData[0]
ENGLISH
Tr o u b l e s h o o t i n g
This section provides many useful tips on how to solve common problems while using the
AVerVision M70.
There is no picture on the presentation screen.
1.
2.
3.
4.
Check all the connectors again as shown in this manual.
Check the on/off switch of the display output device.
Verify the setting of the display output device.
If you are presenting from a notebook or computer through the display output device, check the
cable connection from computer RGB (VGA) output to RGB input of AVerVision M70 and make
sure AVerVision M70 is in PC Mode.
5. For HDMI display output, a delay occurs while waiting for both the display device and M70 to
sync up. Wait for around 4 to 7 seconds until you see the camera image on the screen.
I have set up the AVerVision M70 and checked all the connections as specified in
the manual but I cannot get a picture on the preferred presentation screen.
1. The unit POWER button turns orange in standby mode. Press the POWER button again to turn
on and the LED light will turn blue.
2. The default camera display resolution setting is on 1024x768. If your output device does not
support this resolution; no image can be projected. Simply press hold the FREEZE and ► button
to the change the resolution setting.
3. If your display output device is on TV or any analog device, please switch the TV-RGB dip switch
to TV.
The picture on the presentation screen is distorted or the image is blurry.
1. Reset all changed settings, if any, to the original manufacturer default setting. Press DEFAULT on
the remote or select Default in Basic tab OSD menu.
2. Use the Brightness and Contrast menu functions to reduce the distortion if applicable.
3. If you discover that the image is blurry or out of focus, press the Auto Focus button on the control
panel or remote control.
There is no computer signal on presentation screen.
1. Check all the cable connections among the display device, AVerVision M70 and your PC.
2. Connect your PC to the AVerVision M70 first before you power on your computer.
3. For notebook, repeatedly press FN+F5 to toggles between display modes and display the
computer image on the presentation screen. For different command, please refer to your laptop
manual.
The presentation screen does not show the exact desktop image on my PC or
Notebook after I toggle from Camera to PC mode.
1. Return to your PC or Notebook, place the mouse on the desktop and right click, choose
“Properties”, choose “Setting” tab, click on “2” monitor and check the box “Extend my Windows
desktop onto this monitor”.
2. Then go back one more time to your PC or Notebook and place the mouse on the desktop and
right click again.
3. This time choose “Graphics Options”, then “Output To”, then “Intel® Dual Display Clone”, and
then choose “Monitor + Notebook”.
4. After you follow these steps, you should be able to see the same desktop image on your PC or
Notebook as well as on the presentation screen.
38
ENGLISH
AVerVision M70 can’t detect the inserted USB flash drive.
Make sure the USB flash drive switch is set to the right and check if the USB flash drive is properly
inserted.
I have connected the mouse/AP20T and switch to playback single image preview or
in camera freeze mode but still the Annotation control panel doesn’t show up.
1. Check the USB switch on the left panel is set to
.
2. Make sure the resolution setting is set to the annotation supported resolution setting of either
1024 x 768, 1280 x 720, or 1280 x 1024.
The recorded video on MAC with the bundled software doesn’t have sound.
Due to some limitation, we recommend recording the audio directly from the MAC MIC IN port for
better audio quality.
Li m i ted War r anty
For a period of time beginning on the date of purchase of the applicable product and extending as set
forth in the “Warranty Period of AVer Product Purchased” section of the warranty card, AVer
Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to
AVer’s documentation for the product and that its manufacture and components are free of defects in
material and workmanship under normal use. “You” as used in this agreement means you individually
or the business entity on whose behalf you use or install the product, as applicable. This limited
warranty extends only to You as the original purchaser. Except for the foregoing, the Product is
provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without
problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy
and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or
replacement of the Product with the same or a comparable product. This warranty does not apply to
(a) any Product on which the serial number has been defaced, modified, or removed, or (b) cartons,
cases, batteries, cabinets, tapes, or accessories used with this product. This warranty does not apply
to any Product that has suffered damage, deterioration or malfunction due to (a) accident, abuse,
misuse, neglect, fire, water, lightning, or other acts of nature, commercial or industrial use,
unauthorized product modification or failure to follow instructions included with the Product, (b)
misapplication of service by someone other than the manufacturer’s representative, (c) any shipment
damages (such claims must be made with the carrier), or (d) any other causes that do not relate to a
Product defect. The Warranty Period of any repaired or replaced Product shall be the longer of (a) the
original Warranty Period or (b) thirty (30) days from the date of delivery of the repaired or replaced
product.
Limitations of Warranty
AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained,
and used in accordance with AVer specifications. Specifically, the warranties do not extend to any
failure caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or
misuse, (ii) fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any
accessories or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or
repair of the Product by anyone other than AVer or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH
RESPECT TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE
39
ENGLISH
USAGE OR PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED
TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION,
OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF OR IN
CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF ANY
PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY
OTHER LEGAL THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. AVER’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE,
REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY
YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
Governing Law and Your Rights
This warranty gives you specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.
For warranty period, please refer to the warranty card.
40
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising