Dalian Dongfu Color Display Co.,Ltd LCD Module User Manual DM

Dalian Dongfu Color Display Co.,Ltd LCD Module User Manual DM
LCD Module User Manual
Dalian Dongfu Color Display Co.,Ltd
LCD Module User Manual
DM 12864-27
Tel.:
86-411-84619565
Fax:
86-411-84619585
E-mail:sales @ dongfu.com
Website: http://www.dongfu.com
Dalian Dongfu Color Disply Co.,Ltd
Page 1 of 14
LCD Module User Manual
REVISION RECORD
REV. NO.
DATA
REVISION ITEMS
1.0
JAN 20, 2006
First Release Version
Dalian Dongfu Color Disply Co.,Ltd
Page 2 of 14
LCD Module User Manual
Contents
1.Scope----------------------------------------------------------------------------4
2.Warranty------------------------------------------------------------------------4
3.Features-------------------------------------------------------------------------4
4.Mechanical Diagram---------------------------------------------------------6
5.I/O Terminal--------------------------------------------------------------------7
6. Quality Level------------------------------------------------------------------9
7.Reliability----------------------------------------------------------------------13
8.Handling Precautions------------------------------------------------------13
9.Precautions for Use---------------------------------------------------------14
Dalian Dongfu Color Disply Co.,Ltd
Page 3 of 14
LCD Module User Manual
1.Scope
This manual defines general provisions as well as inspection standards for standard LCD
module. If the event of unforeseen problem or unspecified items may occur, please contact the
nearest supplier or our company.
2.Warranty
If module is not stored or used as specified in this manual, it will be void the 12 month
warranty.
3.Features
3-1.
Features
(1) Display mode:
reflective type
STN LCD
(2) Display color:
Display dots: Black
Background:Yellow—Green
(3) Display Fonts:
Graphics Matrix
(4)Input data: 8-bit parallel data interfaced from a MPU
(5) Multiplex ratio:
1/64 Duty, 1/9 Bias
(6)Viewing direction: 6 O’clock
(7) Back light:
No
(8) Controller:
KS0108
3-2. Mechanical features
Item
Specifications
Unit
Outline dimensions
93.0(W)×70.0(H) ×9.0Max.(T)
mm
Viewing Area
71.7(W)×39.0(H)
mm
Image Area
66.52(W)×32.44(H)
mm
Number of Dots
128(W) ×64(H)
mm
Dot Size
0.48(W)×0.48(H)
mm
Dot Pitch
0.52(W)×0.52(H)
mm
Weight
---
g
3-3. Absolute maximum ratings
Item
Symbol
Condition
Min
Max
Units
Power supply for logic
Vdd
25℃
﹣0.3
7.0
V
Operating voltage for LCD
Vee
25℃
VDD-19.0
Vdd+0.3
V
Input voltage
Vin
25℃
﹣0.3
Vdd+0.3
V
Operating temperature
Top
---
0
50
℃
Storage temperature
Tstg
---
﹣20
70
℃
Dalian Dongfu Color Disply Co.,Ltd
Page 4 of 14
LCD Module User Manual
Note:
1)
The modules may be destroyed if they are used beyond absolute maximum ratings. In
ordinary operation, it is desirable to use them within recommended operation conditions.
Using the modules beyond these conditions may cause malfunction and poor reliability.
2)
All voltage values are referenced to GND=0V.
3-4 Electrical characteristics (VDD=5.0V, Vss=0V,Ta = 25℃)
Item
Symbol
Logic
Power Voltage
LCDdrive
Input High Voltage
Input Low Voltage
Output Voltage
Condition
Min.
Typ.
Max.
Vdd
----
5.0
---
Vdd-Vee
---
13.4
---
Vih1
0.7Vdd
---
Vdd
Vih2
2.0
---
Vdd
Vil1
0
---
0.3Vdd
Vil2
0
---
0.8
Unit
V
“H” Level
Voh
-Ioh=200uA
2.4
---
---
“L” Level
Vol
Iol=1.6mA
---
---
0.4
190
270
350
KHz
---
1.3
---
mA
Frame Frequency
Fosc
Power Consumption
Idd
Vdd=5.0V Rf=75k
Ω±2%
Note: All the dots are in the static state.
3-5.Example of power supply
Dalian Dongfu Color Disply Co.,Ltd
Page 5 of 14
LCD Module User Manual
14.0
48.26
66.52(I.A.)
7
3
4. Mechanical Diagram
32.44(I.A.)
65.0
NOTE:
TOLERENCES UNLESS OTHERWISE SPECIFIED:±0.2
ALL DIMENSIONS ARE IN mm
Dalian Dongfu Color Disply Co.,Ltd
Page 6 of 14
LCD Module User Manual
5.I/O Terminal
5-1 I/O Connection
Pin No.
Symbol
Function
1
VSS
Power supply (GND)
2
VDD
Power supply (+5.0V)
3
V0
Contrast adjust
Input terminal, interfaced with MPU
Register select signal
4
D/I=0, Instruction register (for write)
D/I
Busy flag: address counter ( for read)
D/I=1, Data register (for write and read)
Input terminal, interfaced with MPU
5
Data read/write
R/W
R/W=1
Read ;R/W=0
Write
Input terminal, interfaced with MPU
6
E
7-14
DB0-DB7
Data bus line
15
CS1
This is the chip select signal.
16
CS2
This is the chip select signal.
17
RST
When /RST is set to “L,” the settings are initialized.
18
VEE
Power supply for LCD
19
BL+
Power supply for LED (+)
20
BL-
Power supply for LED (-)
Enabe signal
5-2 Signal timing diagra
Dalian Dongfu Color Disply Co.,Ltd
Page 7 of 14
LCD Module User Manual
5-3. Instruction Table
Dalian Dongfu Color Disply Co.,Ltd
Page 8 of 14
LCD Module User Manual
5-3
Display command
Note:The details of The Display Commands ,please refer to KS0108/PT6608data sheet.
Dalian Dongfu Color Disply Co.,Ltd
Page 9 of 14
LCD Module User Manual
6. Quality Level
6-1 Inspection conditions
6-1-1The environmental conditions for inspection shall be as follows:
Room temperature: 20±3℃
Humidity: 65±20% RH
6-1-2 The external visual inspection:
The inspection shall be performed by using a 20W fluorescent lamp for illumination and the
distance between LCD and the eyes of the inspector should be at least 30cm.
(1) Light method
(2) Inspection distance and angle
6-2 Sampling procedures for each item’s acceptance level table
Defect type
Sampling procedure
AQL
MIL-STD-105D Inspection Level I
Major defect
QC/-07-2006(1)
Normal inspection
Single sample inspection
MIL-STD-105D Inspection Level I
Minor defect
Normal inspection
QC/-07-2006(1)
Single sample inspection
6-3 Classification of defects
6-3-1 Major defect
A major defect refers to a defect that may substantially degrade usability for product
applications.
6-3-2 Minor defect
A minor defect refers to a defect that deviates from existing standards almost
unrelated to the effective use of the product or its operation.
Dalian Dongfu Color Disply Co.,Ltd
Page 10 of 14
LCD Module User Manual
6-4 Inspection standar
Item
Defect
Criterion for defects
type
1) Display on inspection
(1) Non display
(2) Vertical line is deficient
(3) Horizontal line is deficient (4) Cross line is deficient
Size Φ(mm)
Acceptable number
Φ≤0.3
2) Black/White spot
Major
Ignore (note)
0.3<Φ≤0.45
3
0.45<Φ≤0.6
1
0.3<Φ
0
Minor
(Note) Not allowed if four more spots crowd together
Length (mm)
Width (mm)
L≤10
3) Black/White line
Acceptable number
W≤0.03
Ignore
5.0≤L≤10
0.03<W≤0.04
3
5.0≤L≤10
0.04<W≤0.05
2
1.0≤L≤10
0.05<W≤0.06
2
1.0≤L≤10
0.06<W≤0.08
1
L≤10 0.08<W
Minor
follows 2) point defect
Defects separate with each other at an interval of more than 20mm.
4) Display pattern
Minor
[Unit: mm]
A+B≤0.45
0<C D+E≤0.35 F+G≤0.35
2
2
2
Note: 1) Up to 3 damages acceptable
2) Not allowed if there are two or more pinholes every 3 of
fourths inch.
Size Φ(mm)
Φ≤0.7
5) Spot-like contrast
irregularity
Acceptable Number
Ignore (note)
0.7<Φ≤1.0
3
1.0<Φ≤1.5
1
1.5<Φ
0
Note: 1) Conformed to limit samples.
2)Intervals of defects are more than 30mm.
Dalian Dongfu Color Disply Co.,Ltd
Page 11 of 14
Minor
LCD Module User Manual
Item
Criterion for defects
Defect
type
Size Φ(mm)
Φ≤0.4
6) Bubbles in polarizer
7) Scratches and dent on the
polarizer
8) Stains on the surface of LCD
panel
9) Rainbow color
10) Viewing area
encroachment
11) Bezel appearance
12) Defect of land surface
contact
Acceptable Number
Ignore (note)
0.4<Φ≤0.65
2
0.65<Φ≤1.2
1
1.2<Φ
0
Scratches and dent on the polarizer shall be in the accordance
with “2) Black/white spot”, and “3) Black/White line”.
Stains which cannot be removed even when wiped lightly
with a soft cloth or similar cleaning.
No rainbow color is allowed in the optimum contrast on state within
the active area.
Polarizer edge or line is visible in the opening viewing area due to
polarizer shortness or sealing line.
Minor
Minor
Minor
Minor
Minor
Rust and deep damages that are visible in the bezel are rejected.
Minor
Evident crevices that are visible are rejected.
Minor
(1) Failure to mount parts
13) Parts mounting
(2) Parts not in the specifications are mounted
Major
(3) For example: Polarity is reversed, HSC or TCP falls off.
14) Part alignment
(1) LSI, IC lead width is more than 50% beyond pad outline.
(2) More than 50% of LSI, IC leads is off the pad outline.
Major
(1) 0.45<Φ, N≥1
15) Conductive foreign
matter (solder ball,
solder hips)
(2) 0.3<Φ≤0.45,
Minor
N≥1
Minor
Φ: Average diameter of solder ball (unit: mm)
(3) 0.5<L, N≥1
Minor
L: Average length of solder chip (unit: mm)
(1) Deep damage is found on copper foil and the pattern is nearly
16) PCB pattern damage
Major
broken.
(2) Damage on copper foil other than 1) above
Minor
(1) Due to PCB copper foil pattern burnout, the pattern is
connected, using a jumper wire for repair;2 or more places
17) Faulty PCB correction
are corrected per PCB.
Minor
(2) Short-circuited part is cut, and no resist coating has been
performed.
18) Bezel flaw
Bezel claw missing or not bent
Minor
(1) Failure to stamp or label error, or not legible.(all acceptable if
19) Indication on name plate
(sampling indication label)
legible)
(2) The separation is more than 1/3 for indication discoloration, in
which the characters can be checked.
Dalian Dongfu Color Disply Co.,Ltd
Page 12 of 14
Minor
LCD Module User Manual
7.Reliability
7-1 Lifetime
50,000 hours (25℃ in the room without ray of sun)
7-2 Items of reliability
Item
Condition
Criterion
1) High
60℃
Temperature
96hrs
No cosmetic failure is allowable.
Operating
Contrast ratio should be between initial value
±10%.
2) Low
Temperature
-20℃
96hrs
Total current consumption should be below
Operation
double of initial value.
3) Humidity
4)
40℃, 90%RH, 96hrs
High
Temperature
5)
Low
Temperature
6) Thermal
shock
70℃
96hrs
-30℃
96hrs
Contrast ratio should be between initial value
±20%.
25℃→30℃→25℃→70℃
5(min) 30(min) 5(min) 30(min)
5 cycle, 55~60%RH
10~55~10hz
7) Vibration
No cosmetic failure is allowable.
amplitude: 1.5mm
2hrs for each direction
(X,Y,Z)
Total current consumption should be below
double of initial value.
No defects in cosmetic and operational function
are allowable.
Total current consumption should be below
double of initial value.
8.Handling Precautions
8-1 Mounting method
A panel of LCD module consists of two thin glass plates with polarizers that easily get
damaged.
And since the module in so constructed as to be fixed by utilizing fitting holes in the printed
circuit board (PCB).
Extreme care should be used when handling the LCD modules.
8-2 Cautions of LCD handling and cleaning
When cleaning the display surface, use soft cloth with solvent (recommended below) and
wipe lightly.
…
Isopropyl alcohol
…
Ethyl alcohol
…
Trichlorotriflorothane
Do not wipe the display surface with dry or hard materials that will damage the polarizer
surface.
Do not use the following solvent:
…
Water
…
Ketone
…
Aromatics
Dalian Dongfu Color Disply Co.,Ltd
Page 13 of 14
LCD Module User Manual
-
8-3 Caution against static charge
The LCD module use C-MOS LSI drivers. So we recommend you:
Connect any unused input terminal to Vdd or Vss. Do not input any signals before power is
turned on, and ground your body, work/assembly areas, assembly equipment to protect
against static electricity.
8-4 Packaging
- Module employs LCD elements, and must be treated as such.
Avoid intense shock and falls from a height.
To prevent modules from degradation, do not operate or store them exposed direct to
sunshine or high temperature/humidity.
8-5 Caution for operation
- It is an indispensable condition to drive LCD module within the limits of the specified
voltage since the higher voltage over the limits may cause the shorter life of LCD
module.
An electrochemical reaction due to DC (direct current) causes LCD undesirable
deterioration so that the uses of DC (direct current) drive should be avoided.
- Response time will be extremely delayed at lower temperature than the operating
temperature range and on the other hand at higher temperature LCD module may
show dark color in them. However those phenomena do not mean malfunction or out of
order of LCD module, which will come back in the specified operating temperature.
8-6 Storage
In the case of storing for a long period of time, the following ways are recommended:
- Storage in polyethylene bag with the opening sealed so as not to enter fresh air
outside in it. And with not desiccant.
- Placing in a dark place where neither exposure to direct sunlight nor light is. Keeping
the storage temperature range.
- Storing with no touch on polarizer surface by any thing else.
8-7 Safety
- It is recommendable to crash damaged or unnecessary LCD into pieces and to wash
off liquid crystal by either of solvents such as acetone and ethanol, which should be
burned up later.
- When any liquid leaked out of a damaged glass cell comes in contact with your hands,
please wash it off well at once with soap and water.
9.Precautions for Use
9-1
Both parties should provide a limit sample on an occasion when both parties agree its
necessity.
The judgement by a limit sample shall take effect after the limit sample has been
established and confirmed by both parties
9-2 On the following occasions, the handling of problem should be decided through
discussion and agreement between responsible of the both parties.
-When a question is arisen in this manual.
-When a new problem is arisen which is not specified in this manual.
-Some problem is arisen due to the change of inspection and operating conditions in
users.
-When a new problem is arisen at the customer’s operating set for sample evaluation in
the customer site.
Dalian Dongfu Color Disply Co.,Ltd
Page 14 of 14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement