Euro-2100 - JUTA
Euro-2100
User manual
manual version 1.0
This manual was not subject to any language revision.
This manual cannot be copied or otherwise forwarded without editor’s consent.
All rights reserved © 2006, Elcom s. r. o.
Euro-2100
Obsah
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Basic definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Department. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tax level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sales units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PLU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Relationship between departments and PLUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bar code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Bar-code scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cumulated totals (grandtotals) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cash register characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Parts of the cash register, basic parameters. . . . . . . . . . . . . . . . . . . . . . . .11
Extensibility options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Euro-2100 keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Names and functions of ECR keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cashier display description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Customer display description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ECR displays description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Mode switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Paper ribbons installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Usage and storage of thermal paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Calculator feature description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Programming manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Initialisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Recommended procedure for Euro-2100 programming . . . . . . . . . . . . .19
Flags programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Initial programming of system flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
System flags correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Printing flags values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Flag 1 – Number of decimal places, method of rounding, TAX system… . . . . . . . . . . 20
Flag 2 - TAX printing, number of logo lines, blank lines…. . . . . . . . . . . . . . . . . . . . . 20
Flag 3 - Receipt consecutive number, cash register number . . . . . . . . . . . . . . . . . . . . . 20
Flag 4 - Required operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Flag 5 - Parameters of serial communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Flag 6 - Printing mode setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Flag 7 - Limit and value of the percent add-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Flag 9 - Time setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Extended flags programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Flag 8 - Limit and value of the percent discount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Flag 10 - Date setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
© Elcom, s. r. o.
© Elcom, s. r. o.
Euro-2100
Tax rates programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Correction of the tax level values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Printing of the preprogrammed tax values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Receipt logo programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Correction of the logo lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Printing the programmed logo lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cashier programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Correction of cashiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Printing of Cashier values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Function text programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Correction of function texts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Printing function texts setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Departments programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Correcting departments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Printing department values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sale unit programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Correcting programmed sale units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Printing sale unit settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Article items (PLU) programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Programming procedure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting up the bar-code scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Quick PLU price programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Quick PLU stock programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Correction of programmed PLUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Printing the programmed PLUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Programming the euro currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Stage without euro currency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
First euro currency stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Procedure for entering the first euro stage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Second euro currency stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Third euro currency stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Entering texts into ECR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Programming of programmable keyboard keys . . . . . . . . . . . . . . . . . . . .33
Deleting the key function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Printing of the programmed key name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Printing of the programmed key function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Printing the settings for all keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Operation in registration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Recommended procedures at the beginning of the day . . . . . . . . . . . . . .35
Printing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Status and functions required at the beginning of registration. . . . . . . . .35
Error warning: the Clear key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cashier log in: the Password key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cashier log out: the (Password) key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Finalizing a transaction: Cash, Cheque, Credit keys . . . . . . . . . . . . . . . . . . . . . . . 36
Samples of basic registration procedures . . . . . . . . . . . . . . . . . . . . . . . . .36
Registration using departments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Basic registration using departments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Registration using departments with price entry using keyboard . . . . . . . . . . . . . . . . . 37
Registration using departments with pre-programmed price . . . . . . . . . . . . . . . . . . . . 38
Registering multiple items using departments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Multiplying items during registration using departments. . . . . . . . . . . . . . . . . . . . 38
Registering fractions of items using departments . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Double multiplication of items during registration using departments . . . . . . . . . 39
Euro-2100
Single item sales using into departments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Basic PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Multiplication in PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Individual PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Overriding the pre-programmed PLU price. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Fractional PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Double multiplication in PLU registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Other means of registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Registration using bar-codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Weight entry by electronic scales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Registration using an external PC keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PC ON-LINE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Data are transmitted from a PC to the cash register . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Data are transmitted from the cash register to PC: . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Percent surcharge and discount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Percent surcharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Percent discount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Reference number and customer number . . . . . . . . . . . . . . . . . . . . . . . .46
Received on account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Paid out (cash or cheque) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Refunds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Registration using the euro currency. . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Stage without euro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
First euro currency stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Second euro currency stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Third stage of the Euro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
How to print out reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Generated reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Report contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Department report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
PLU report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Stock level report. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Financial report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cashier report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Total daily “X” report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Periodical “X” report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Total daily “Z” report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Periodical “Z” report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
How to print “X” reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Samples of “X” reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Samples of “Z” reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
How to print “Z” reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Euro2A software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Optional ECR accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Cash drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Electronic scales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Bar-code scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Metrologic MS-5145 ECLIPSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
© Elcom, s. r. o.
© Elcom, s. r. o.
Euro-2100
Metrologic MS-6720 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Metrologic Orbit MS-7120 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Metrologic MS-7625 - Horizon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Metrologic MS-9520 Voyager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Electronic payment terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
External keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
UV LED banknote checker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Optional internal battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
LAN connection options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
New features of Elcom ECRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Helpful advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Information and error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
What to do in case of power failure? . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Failures of register as a result of interference in power network . . . . . . . . . . . . . . . 63
What to do in case of “Low BAT., finish sale ” signal . . . . . . . . . . . . . . .63
Self tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Self-test of the electronics and display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Self-test of the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Self-test of keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Service codes of the ECR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Introduction
Euro 2100
© Elcom, s. r. o.
Introduction
Dear customer,
You have selected the state-of-the-art electronic cash register Euro-2100 in which you get not
only an ardent helper, but also a tool that greatly helps your management.
Thank you for the confidence you show in using our product and we believe that Euro-2100 will
help you manage your store effectively and help you reach desired success.
We would greatly appreciate when you share your experience with operation of this cash register,
which will allow us to customise this product to suit your needs.
Important
•
•
•
•
•
•
•
•
•
•
•
•
•
Install the cash register in a place where it will not be exposed to direct sunlight, unusual temperature changes (under 0 °C and above 50 °C) or high humidity. Installation in such places
could result in damage to both the cabinet and electrical components.
In the case that internal battery is included:
- Leave the cash register turned on for at least 8 hours to charge internal accumulator to full
capacity,
- It is strongly recommended to start battery charging after battery discharge signalling to
ensure long operating life and preservation of the battery capacity,
- If the external power adapter is connected to the cash register, internal battery is charged
also in the case that cash register is turned off.
When the cash register battery is charged, the cover can increase its temperature. We do not
recommend to place the cash register near flammable materials.
After transporting the unit from a cold environment to a warm one and vice-versa, do not
switch the cash register on for a minimum of 20 minutes in order to give all components time
to adjust to the new temperature conditions.
An individual having wet hands should not operate the cash register. Water could seep into
the interior of the Euro-2100 and cause component failure.
Clean the cash register with a dry, soft cloth. Never use cleaning agents such as petrol or solvents. Using such chemicals can result in discolouration or deterioration of cabinet.
Avoid spilling of any liquids on the cash register as they may cause damage. The keyboard
should be carefully protected.
Connect the cash register with the supplied adapter into a standard network plug (230V ±
10). Other electrical equipment connected in the same network circuit may cause improper
functioning of the cash register. In an environment with strong interference use the special
anti-interference aids recommended by the manufacturer of the cash register.
If the cash register malfunctions, contact your authorised dealer for service. Do not try to
repair the register yourself. Do not open the cash register!
Pull out the AC/DC adapter plug from its electrical plug if the device is to be fully disconnected.
If the external adapter is connected to the cash register, then the internal lead acid accumulator is charged even when the cash register is turned off.
During a receipt printing, wait until the printer has finished before tearing the receipt. Do
not tear off the receipt during printing as printer damage may result.
If the red streak appears at the end of the paper ribbon, exchange this ribbon as soon as
possible. If the ribbon is exchanged too late, it can damage the printer, or decrease its lifetime.
7
© Elcom, s. r. o.
Euro 2100
•
•
•
•
•
•
•
•
•
•
Introduction
Use the paper ribbon, whose end is not glued. If such paper ribbon is used and not exchanged
early enough, the printer could be damaged or its lifetime could be shortened. In this case,
the damaged printer warranty is not valid.
Use only high-quality thermal paper ribbons. Improper ribbons may damage the printer or
shorten its lifetime. When using suitable ribbons and by properly maintaining the printer,
the average lifetime is up to 25 million lines!
Journal paper storage recommendations: Do not expose thermal paper to light. Store at a
temperature not higher than 40 °C. Avoid contact of thermal paper with PVC, mollificators,
organic solvents or glue.
Use only the supplied AC/DC adapter or a source recommended by an authorised dealer for
electrical connection. The use of other adapter types may result in damage to the adapter or
the cash register.
Use only the program recommended by your authorised dealer and use only the original interconnecting cable for cash register communication with a computer. For bar code scanners,
use only the connector recommended in these instructions.
If the cash register is not to be used for a long time, it is necessary to turn on the cash register for at least eight hours every half year to charge the internal NiCd memory back up accumulator and to prevent data memory loss. Note that the capacity of the internal lead acid
accumulator drops to about 70  in six months.
If the cash register is used in ways other than those described in these instructions, the dealer
cannot be responsible for incorrect data or damage that may result.
Only equipment which meets the European Union standards (CE) can be connected to the
Euro-2100. In other cases, the Elcom company cannot guarantee the adherence to standards
of whole system. Ask the Elcom company or your authorised dealer of Euro-2100 for more
information.
The symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable take-back
scheme for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the enviroment and human health.
Do not leave appliance unattended while it is in use.
Basic definitions
Logo
The heading on each printed receipt is introductory information preceding the description of
the purchased goods. It is mainly used to identify the cash register owner (company name, tax
information, company identification, etc.).
Figure 1.1
>
"%#)*%(
F?=NLIHC=?KOCJG?HN
#
#
*$!/%+
3IOLL?=?CJN
Receipt logo.
Department
Departments (DPTs) are used to denote groups of goods having some common features (dairy
products, foodstuffs, fruit, etc.). A department is characterised by it’s name, parameters, and by
the preprogrammed selling price, if it is used for direct sale.
8
© Elcom, s. r. o.
Euro 2100
Introduction
Tax level
Tax level is used for the tax assessment of the sales line. It’s characterized by the percent value and
tax type (VAT, DO).
Sales units
Sales units are used in connection with the quantity of goods sold (metres, litres, etc.). Each PLU
has assigned a specific sales unit in which the quantity of the goods sold is indicated. It’s possible
to program 15 sales units with a maximum of three characters.
PLU
PLU (Price Look Up) is an abbreviation for the denomination of the specific goods (goods item).
The PLU code represents the article name, the sale price and flags (assignment to an department,
VAT level, PLU type etc.). For example: Fat milks - 0,85 GBP, White yoghurt - 1,20 GBP). If the
good has an assigned bar-code, this is used as the PLU.
Relationship between departments and PLUs
The example in figure 1.2 clearly illustrates the relation between the departments and the goods
items (PLU). Sixteen PLU and four goods groups were used here.
<
(00%4
Figure 1.2
Relationship betweem
PLUs and departments.
%15
%15
%15
%15O
%JBSZQSPEVDUT
4XFFUT
1BTUSZ
"MDPIPM
1-6
1-6
1-6
1-6X
'SVJUZPHIVSU
/VUDIPDPMBUF
8IPMFDPSOSPMM
#SBOEZ
1-6
1-6
1-6
1-6Y
4LJNNFENJMLM
5PõFF
#VO
#FFS
1-6
1-6
1-6
1-6Z
$PMCZDIFFTF
8BõFST
.BJ[FCSFBE
7PELB
1-6
1-6
1-6
1-6[
.POUFSSFZ+BDL
'VEHFDBOEZ
$SPJTTBOU
8JOF
Report
A report is a sales overview of a particular choice (financial, total, cashier, PLU etc.)
There are two basic types of reports: “X” and “Z”.
“X” reports print the concrete sales values (according to the report chosen) without resetting
the data.
“Z” reports print the sales values of the chosen report. After printing the values, all values are
then reset to zero in the cash register memory.
Bar code
Coding of the numeric description of products into bars corresponds with clearly defined international rules. If a product has an assigned bar-code, it appears on each of these goods. The most
frequently used code for product or merchandise denomination in Europe is the 13-digit code
according to the EAN norm (EAN-13) and the 8-digit code (EAN-8).
9
© Elcom, s. r. o.
>
Figure 1.3
Euro 2100
Introduction
Bar-code scanner
EAN bar-codes.
A bar-code scanning device is used to improve speed and accuracy in good registration.
System flags
>> Figure 1.4
Bar-code scanner.
System flags are basic settings of the register that largely influence correctness of cash register functions (Number of decimal places, system of numbers rounding, date,
time, etc.).
Cumulated totals (grandtotals)
Cumulated totals are variables that cumulate the values from all sales. There are usually three
known grandtotals: GT1, GT2, and GT3. Their meaning is as follows:
GT1 - gross turnover - this means the cumulated total of all positive values registered in the
ECR
GT2 - net turnover - the net turnover means the difference between gross turnover and negative
turnover
GT3 - negative turnover - this means the cumulated total of all negative vlaues (voidances, refunds, discounts...) registered in the ECR.
10
Euro-2100
Cash register characteristics
© Elcom, s. r. o.
Cash register characteristics
Parts of the cash register, basic parameters
The Euro-2100 ECR belongs to the middle
segment of ECRs. It‘s designed for more frequented establishments, convenience stores, bars,
caffés and luxury stores. The long term experience with development and manufacture of
ECR and deployment of the most recent technologies enabled us to produce this mature
electronic cash register. The Euro-2100 ECR
belongs to the top of the class with regard to its
technical parameters and friendliness of use.
Euro-2100 is very well technically equipped -it‘s possible to connect the Euro-2100 to a PC,
attach a bar-code reader, electronic payment
terminal and electronic scales. Other accessories include cash drawer, external PC keyboard or a specialised EK-3000 keyboard which
is especially suited for operation in small stores, restaurants and hotels. The Euro-2100 also
optionally includes an internal battery (which
allows up to eight hours of cordless operation),
an UV LED module for checking of banknotes (excellent built-in device to uncover forgery) and an optional ECR memory extension
(up to 27,000 PLU).
Operator display
The Euro-2100 ECR can be powered from:
•
230V (± 10) power mains via power adapter
• built-in battery (optional)
The packaging contains the ECR itself, power
adapter and CD with support and PC communication software suite.
The optional equipment includes a cash drawer,
electronic scales, bar-code scanner, and internal
battery. The unique ECR feature of Euro-2100
is USB connectivity to a PC. Other PC communication features are communication via
RS-232/RS-485 and RS-232/Ethernet interfaces
and communication using analogue and GSM
modems.
The ECR construction is designed to fit demanding criteria of ideal ergonomy workplace
and offers several ways of positioning the ECR
on the counter or cash drawer using two-sided adhesive tape. ECR design with extensible
props allows for easy access to all communication ports and does not hinder positioning of
the ECR.
Customer display
<
Figure 2.1
Basic features
of Euro-2100 ECR
Receipt gap
Power switch
Programmable
keyboard
Keyboard
Connector panel
Key CALCULATOR
11
Euro-2100
© Elcom, s. r. o.
>
Table 2.1
Euro-2100 ECR
parameters
Designed for
Number of PLU
Number of DPT
Number of cashiers
Cashier identification
Number of VAT levels
Printer
Printing speed
Paper tape
Number of characters
in PLU label
Number of characters
in logo
Logo
Large and small characters
Bold characters
Special characters
Keyboard description
Language for programming
Language for tapes
Language for reports
Small establishments,
convenience stores,
bars, caffés, boutiques
8 000 (27,000)
30
6
password, access rights
6+1
thermal printer
LT1320
max. 17 lines/s
thermal 2×38 mm
20
24/12
up to nine lines
yes
english
The unique built-in touch sensitive keyboard,
which is manufactured using the up-to-date
matrix technology, is the default ECR feature. The unique transparent touch panel allows
easy replacement of key labels and also complements the elegant design of Euro-2100 cash
register. The keyboard is composed of 36 individually programmable keys. The Shift key is
used to programme two levels of data for each
key thus extending the key availability to 72
Cash register characteristics
Reports
Cashier display
Customer display
PC interface
DPT, PLU, cashiers, financial, daily, periodical
alphanumerical,
20+10+6 characters
alphanumerical,
20+10+6
characters
RS-232, USB
Payment terminal inRS-232
terface
Interface for scanner
RS-232
and scales
External keyboard
PC keyboard, EK-3000
Cash drawer
coil based lock, 24 V
Dimensions [mm]
350×320×210
Weight
2,4 kg
adapter
Power supply
(230 V/24 V 1.5 A)
Power management
yes
Power consumption
max. 36 W
internal battery, UV
LED module for checking banknotes, memory expansion to 27,000
Optional equipment
PLU, cash drawer,
electronic scales, scanner, electronic payment
terminal, Ethernet communication module
states. Each key can be programmed to produce any sequence of standard keyboard strokes, such as direct registration of individual
items, departments, discounts and surcharges
etc. Calculator is a new feature that will allow
you to perform arithmetic operations (addition, subtraction, multiplication, and division)
without registering or while receipt is opened.
The ECR offers multiple managerial functions
and reports.
Extensibility options
The optional external devices are plugged
into connectors that are shown in figure 2.3:
power adapter or other external power supply (POWER connector – 1), PC, modem
or electronic payment terminal (PC connector – 2), electronic scales and bar-code reader
(SCAN/SCALE connector – 3), cash drawer
12
(DRAW connector – 4), external keyboard
(KEYB connector – 5) and USB connection to
the PC (6).
Recommendation: Ask your cash register dealer on the possibilities for connecting optional
external devices to the ECR.
Euro-2100
Cash register characteristics
© Elcom, s. r. o.
<
Bar-code scanner
Figure 2.2
External devices connectible to Euro-2100
ECR
Digital scales
Cash drawer
Computer
RS-232
Power adapter 230/24V
RS-232
External keyboard
Payment terminal
Computer
Modem
RS-232
Ethernet communication module
USB
<
Figure 2.3
Rear connnector panel
of Euro-2100 ECR
1
POWER (1):
Power supply adapter port
PC (2): PC/electronic payment terminal port
SCAN./SCALE (3):
Electronic scales/bar-code reader port
2
DRAW. (4):
KEYB. (5):
USB (6):
3
4
5
6
Cash drawer port
External keyboard port
PC USB port
Euro-2100 keyboard
The keyboard is very comfortable and is ready
for daytime work. The keys are marked by larKeyboard of Euro-2100 ECR is divided into
ge simple icons to facilitate ease of orientation.
three basic key groups – department keys, numeric keys and function keys.
Warning: The keyboard is sensitive to dusty
environments, humidity and dirt. Use dry cleIf there are two functions on a single key, then
an cloth to clean the plastic covers of the ECR.
you select the bottom function by simply presNever use cleaning agents as technical gasolising the key. When you wish to use the top
ne or solvents. Such chemicals can damage the
function on a key, the first press and hold Shift
plastic cover or cause discolouration. If you
key, then press the desired button.
13
© Elcom, s. r. o.
Euro-2100
Cash register characteristics
department keys
Figure 2.4 >
The Euro-2100 ECR
keyboard and its composition
programmable keyboard
numerical keys
functional keys
this button allows you to print the concrete
need to clean heavily soiled plastic parts, we reprogrammed values.
commend 3M cleaning spray.
The Scales button is used to register the
weight of goods from the electronic scales. It is
Names and functions of ECR keys also used for PLU stock programming in “P”
mode.
…$ Numerical keys are used for ente- The PO (Paid out) button is used to
ring numerical values and in the programming register the paid out cash or checks from the
cash register as a non-business transaction.
mode „P“ are used for entering text.
… Department keys (used during re- See paid-out function. In the void mode (R or
gistration of department sales), are used for re- T) this button functions as page up or jump
port of department sales in “X” mode and for through 5 items back. It evokes a monthly (periodical) report in “X” or “Z” mode. It is also
department programming in “P” mode.
The Clear button is used to clear an used for logo programming in “P” mode.
amount that has been entered incorrectly from The RA (Received on account) butthe numeric keyboard. This button also cancels ton is used to register the received payments
an incorrectly entered function and the sound if no business transaction has been executed.
signalling ERROR/ALARM. It cancels wrong It records, for example, the insertion of daily
letters when writing texts.
opening cash into the drawer. In the void mode
The Void button is used to correct an (R or T) this button functions as page down or
item that has already been registered. It is also jump forward through 5 items. It is also used
used for function texts programming in “P” for flag programming in “P” mode.
mode.
The Drawer button is used to print
The Refund button enables you to the customer number or other reference numpay back money, e. g. for damaged goods, du- bers on the receipt. It is also used to open the
ring the sale or as an independent transaction. drawer with no sale. In the void mode (R or T)
It is also used for VAT levels programming in this button functions as arrow down or jump
“P” mode.
to next item.
Pressing the EAN button allows you to The Password button is used in
enter the bar code directly from the keyboard “R” and “T” mode to identify the cashier by
in “R” and “T” mode. In “P” mode, pressing password and to permit the cashier to log in.
Through this method, the proper cashier cla-
14
Cash register characteristics
ims responsibility for the transactions. The
name of the logged-in cashier, is printed on
each receipt header. The transactions are recorded in the cashier’s account and are displayed
in the cashier’s report. In the void mode (R or
T) this button functions as arrow up or jump
to the previous item. It is also used to evoke the
cashier report in “X” mode and for the cashier
programming in “P” mode.
The Paper feed button shifts the receipt
ribbon without printing. The receipt ribbon is
fed in 1,5 cm by pressing this button.
Pressing the Receipt button in “T”
and “R” mode allows you to switch the receipt
printing on and off. The printing switched off
is signalled by characters “Prn”.
The Multiply button is utilized for multiplication if two or more pieces of the same
item are being sold. It used for displaying the
time in the registration mode. It is also used to
activate the backlight activation in “X” mode.
The Price button enables manual entry
of an item price rather than the preprogrammed PLU or DPT price. It is also used for fast
PLU price programming in “P” mode.
The PLU button (price look-up) makes
it possible by means of the PLU code to call
out the programmed data about an item, price,
name, department, VAT, etc. See PLU transactions. It evokes a PLU report in “X” or “Z”
Euro-2100
mode. It is also used for PLU programming in
“P” mode.
The Mode button is used for switching
into the individual modes of the cash register. Exit
the STANDBY mode by pressing this button.
After finishing a transaction, print
out the same receipt again by pressing Duplicate button. The receipt is denoted “DUPLICATE”.
The Credit button is used to finalize
the sale in case of credit card payment.
The Check button is used to finalize the
transaction in case of check payment. It also
evokes a financial report in “X” mode and is
used for the programmed data printing in “P”
mode.
a These two buttons are
used to add the percent add-on or to subtract
the percent discount for a particular item or
for the complete transaction according to the
programmed values. The percent add-on button is also used for sales units programming in “P” mode. The percent discount button (shift+cr) is also used for expended flags
programming.
The Subtotal button displays and
prints the actual subtotal value according to the
setting of the fourth system flag.
© Elcom, s. r. o.
ECR displays description
The Total/Cash button is used to finalize the sale in case of cash payment. It also evokes
a daily report in “X” or “Z” mode.
The function in an upper part of a key is
chosen by holding the Shift button and then
pressing the key with two functions
Cashier display description
15-12-2005
P
11:07:39
The displays fully support national characters (if
needed) and allow also other characters (as numerals and special characters). It‘s easy and com-
The cashier display of Euro-2100 is a colour al< Figure 2.5
phanumeric LCD display with 36 characters.
The high quality of display, its contrast and
Alphanumeric
LCD display.
brightness are result of black mask technology.
This type of display complements the unique- prehensive to read from this type of display.
ness of the Euro-2100 cash register. For improved readability, the display is divided into three The customer display has back-light installed
groups: the article name (first row, twenty cha- by default.
racters), amount and type of article (second
Customer display description
row, six characters) and finally the article price
(second row, ten characters). The visibility of
displayed data is also enhanced by the special
green-white colour combination for characters
and by using two character sizes.
15
Euro-2100
© Elcom, s. r. o.
Cash register characteristics
The Euro-2100 customer display is an alphanumeric LCD display (the display type is identical
with the cashier display).
„X“ The „X“ mode is used to print sales reports. The printing of “X” reports does not reThe customer display has back-light installed
set the current sales data.
by default.
Switching into the „X“: Mode switch
15-12-2005
By combining the numerical keys from to
and the % (Mode) button it is possible to set the mode of the cash register. Such
switching thus enables the operator to work
in different cash register modes (registration,
programming, reports, etc.).
„R“ Registration mode. This mode is used
15-12-2005
R
P
11:07:39
„Z“ The „Z“ mode is used to print various
reports. The printing of “Z” reports resets the
cash register sales data.
Switching into the „Z“: „P“ The “P” program mode is used to
program all values and functions of the cash
11:07:39
15-12-2005
for all registrations and transactions. After
T
11:07:39
switching into this mode, the topical time in
the first line and topical date and day in the se- register.
cond line appears on the display until you beSwitching into the “P” mode: 15-12-2005
X
11:07:39
gin registration.
Switching into the „R“ mode: „T“ The training mode provides all functions
of the “R” mode, but in this mode, the transactions are not included in the daily or monthly
(periodical) reports. The receipts printed in
this mode are marked by the text “Invalid document”.
Switching into the “T” mode:
„STANDBY“ When the cash register is not
15-12-2005
Z
STANBY
11:07:39
operated for certain time limit (see chap. 3.3.9,
Flag 6, Digit 5) and it is supplied from internal
power supply, it will switch into the “Standby”
mode. A cash register in the “Standby” mode
has a low consumption of energy. The notification “Standby” appears on the display.
Exit the “STANDBY” mode by pressing the
(Mode) button. In case the cash-register is supplied from external power supply then stand
by mode is not called.
Paper ribbons installation
16
Euro-2100
Cash register characteristics
© Elcom, s. r. o.
<
6
Figure 2.6
Procedure for installing
paper tapes into Euro-2100
ECR (numbers match figure 2.6):
2
5
4
3
7
1
The Euro-2100 cash register uses thermal paper
ribbons of 38 mm width. The right one (a front
view on the cash register) is designed for printing of customer receipts and the left one for
printing the journal.
rection several times. Make sure that the tape
holds firmly in the winding reel. Place the winding reel into the second rear cover (4) in such
way that it will be lightly stretched. Take the
receipt tape (7) and load it into the printer, the
printer will load the tape automatically. Close
Use only rolls of good quality paper with the the tape cover (2). Finally, press button to
maximum diameter of 55 mm. To ensure pro- feed neccessary amount of tape or cut off any
per cash register operation, make sure that the surplus tape.
printing saturation is correct. If any problems
occur, contact your local authorized dealer of Recommendation: If any of the tapes wrinkles
Euro-2100.
or jams during loading, use the printer head
lever to lift the printing head and take out the
Paper ribbons installation procedure for Euro- jammed tape. Fix the tape, lower the printing
2100:
head and try re-loading the tape(s) again.
Press the control button (1) to flip the tape cover (2) open. Take out the paper tape separator
(3) along with empty paper reel cores, remove
them and install new paper tape reels. Insert
the separator with installed tapes into the second rear cover (4). Evenly trim the tapes using
scissors. The tapes‘ ends must not contain dirt
or glue residue. Insert the journal tape into the
printer, the printer will load the tape automatically into its mechanism. Then place the end
of journal tape (5) into the winding reel (6)
and rotate the winding reel in the winding di-
Usage and storage of thermal
paper
The Euro-2100 printer prints on paper 38 mm
wide.
Journal paper storage recommendations:
•
•
do not expose thermal paper to direct light,
store at temperature not higher than 40°C,
17
© Elcom, s. r. o.
Euro-2100
Cash register characteristics
Calculator feature description
Implemented functionality
The built-in calculator is able to perform these
operations on real numbers:
- addition
- subtraction
- multiplication
- dividing
Maximum precision is 13 valid numbers.
The maximum range overflow (±1,79x10308)
error is not handled.
Keyboard operation
You can toggle the calculator functionality
of the ECR using the [CALC] (key (a special
round button on the top edge of the keyboard).
Individual operations are realised using following keys:
PLU
– addition
DPT
– subtraction
MULT
– multiplication
MODE
– dividing
TOTAL
– displays result
CLEAR
– initialises the calculator (ECR
enters the state before calculator has been
used)
Entering and editing numbers:
[1...9] – enter number
[PERIOD] – enter decimal separator
[EAN] – invert sign (positive sign is not displayed)
[VOID] – deletes the last entered number
It‘s possible to enter up to 14 digit signed number, including decimal separator. Single sign
(i. e. sign entered without a number) is ignored. The calculator retains the last performed
operation and it could be repeated using the
TOTAL key.
18
Calculator display
After the ECR is switched into calculator
mode, the bottom display row shows „Calculator“.
Entered numbers are shown in the top display
row; result is displayed similarly.
The current operation sign (+, -, *, /) is displayed in front of the „Calculator“ text in the
bottom row.
Examples:
16
+
Calculation
Display shows after pressing 16 + 45:
45
+
Calculation
Display shows after pressing TOTAL:
61
+
Calculation
Display shows after pressing TOTAL:
While the ECR is in the calculator mode, the
customer display remains empty.
Euro-2100
Programming manual
© Elcom, s. r. o.
Programming manual
Initialisation
Before putting the cash register into operation, 2) Press button. The “Memory cleait must be initialised. The cash register initiaring” label appears on the display.
lisation clears all programmed data and will
return the ECR to default settings. Only folMEMORY CLEARING
lowing data will be preserved: grand totals, reP
10:21:09
port numbers (Z1 and Z2) and value of system
flag no. 1. ECR initialisation is possible only if
daily and periodical reports have been issued 3) To confirm the initialisation, press the
in “Z” mode.
(Subtotal) button. The ECR printer
prints “Memory clearing” and it begins the
Initialisation procedure:
initialisation.
4) After initialisation enter the date
1) Turn the cash register on and press
(DDMMYY) and time (HHMM).
to enter “P” mode.
ENTER DATE
02-02-2005
P
19:05:33
ENTER TIME
Recommended procedure for Euro-2100 programming
The recommended procedure for ECR flags, 2) tax levels, 3) receipt logo, 4) cashiers,
programming advises an user to program- 5) function texts, 6) departments, 7) sale units
me the ECR in the following order: 1) system and finally 8) article items (PLUs).
Flags programming
Prior to programming the system flags, it is re- 1) Switch the cash register into “P” mode
commended that this subchapter is carefully
by pressing
. Notification
studied and clearly understood.
“PROGRAMMING MODE P” appears on
the display. Only a cashier authorised for
Note: If a key is used for two functions, choose
the programming mode can set the ECR
the function in a lower part of key by pressing
into “P” mode.
the key. To choose the function in the upper
part of a key, hold the (Shift) key and
301112
press the particular key.
SF1:
Initial programming of system
flags
2) Press button.
3) After entering flag values, store them by
The system flags represent settings that have
pressing the (Subtotal) button. The
primary influence on the proper performance
programming of the next flag follows. Conof ECR (number of decimal places, rounding,
tinue until you have programmed all necesdate, time, etc.).
sary flags.
4) Finish flags programming by pressing the
System flags programming procedure:
(Total) button.
19
Euro-2100
© Elcom, s. r. o.
System flags correction
1) To change the setting of any of the system
flags, switch the cash register into the “P”
mode by pressing .
2) Enter the flag number to be edited and
press the (RA) button.
3) Enter desired flag value and press the
(Subtotal) button.
4) Print the new programmed settings by
pressing the (Check) button.
Programming manual
5) Finish the programming by pressing the
(Total) button.
Printing flags values
In the programming mode, select the flags
programming by pressing the (RA)
button. Press the (Check) button to print
the flags values. It is possible to print the value
of currently programmed flag by pressing the
(EAN) button.
Flag 1 – Number of decimal places, method of rounding, TAX system…
Figure 3.1 >
First system
flag values.
Digit
1
Default
setting
0
Meaning
Valid values
System of rounding:
0 – up from 5, 1 – always up, 2 –
always down, 3 –special rounding
0 – VAT
1 – TAX
2
0
Tax system:
3
2
4
2
5
2
6
2
No. of decimal places to which total price
should be rounded
No. of decimal places to which VAT should
by rounded
No. of decimal places to which price should
be rounded
No. of decimal places to which price, VAT
should be displayed
0–3
Flag 2 - TAX printing, number of logo lines, blank lines…
Figure 3.2 >
Second system
flag values.
Digit
1
Default
setting
1
2
3
4
0
3
2
5
6
6
0
Meaning
Valid values
TAX values printing
0 – TAX values not printed,
1 – TAX values printed on receipt
Date format
0 – dd-mm-yy, 1 – mm-dd-yy
No. of decimal places of amount values
0–3
Number of blank lines between succeeding
0 – 6)
receipts
Number of logo lines
Split pricing/successive multiplication entries 0 – split pricing, 1 – successive
multiplication
Flag 3 - Receipt consecutive number, cash register number
Figure 3.3 >
Third system
flag values
Digit
1
2–3
4–7
Default
setting
0
01
0001
Meaning
Valid values
Receipt consecutive number clearing
0 – after “Z” total (daily) report, 1
– after “Z” periodical report
(01 – 99)
(01 – 9 999)
Cash register number
Receipt consecutive number
Flag 4 - Required operations
Digit
1
20
Default
setting
1
Meaning
Valid values
Subtotal amount printing after Subtotal key 0 – no, 1 – yes
is pressed
Euro-2100
Programming manual
2
0
3
0
4
0
© Elcom, s. r. o.
Required Subtotal key pressed before receipt 0 – not required, 1 – required
is finished
Required Credit Card number entering if 0 – not required, 1 – required
paid by Credit
Required customer’s payment amount ente- 0 – not required, 1 – required
ring
<
Figure 3.4
Fourth system
flag values.
Flag 5 - Parameters of serial communication
Digit
1
Default
setting
0
2
3
3
1
4
0
5
0
6
0
<
Meaning
Valid values
Programming of the terminal code for the
bar code scanner
Programming of communication speed of
the bar code scanner
Programming of communication speed of
the PC
Communication protocol for Electronic scales
0 – terminator CR and LF, 1 – terminator CR, 2 – terminator LF
0 – 1 200 Bd, 1 – 2 400 Bd, 2 – 4 800
Bd, 3 – 9 600 Bd, 4 – 19 200 Bd
0 – 9 600 Bd, 1 – 38 400 Bd
Figure 3.5
Fifth system
flag values.
0 – CAS Morcan, MARTES T,
1 – Euro scales, MARTES M,
2 – Macca K, 3 – not used
Data transmission direction in PC-ON 0 – PC transmits, 1 – PC transLINE mode
mits and receives
Communication protocol for payment ter- 0 – communication is not allowed,
minal
1 – Bull Amadeo, 2 – PinPad KeyCorp
Flag 6 - Printing mode setting
Digit
1
Default
setting
0
2
0
3
4
1
0
5
1
6
2
7
0
Meaning
<
Valid values
Figure 3.6
Sixth system
flag values.
Printing modes without external power sup- 0 – normal mode, 1 – economical
ply
mode, 2 – high speed mode
Printing modes with external power supply
0 – normal mode, 1 – economical
mode, 2 – high speed mode
Graphical logo printing
0 – no, 1 – yes
Height of printing font
0 – normal font: character height
of 2.5 mm, 1 – not used
Standby mode
0 – standby inactive, 1 – standby
after 1 min., 2 – standby after 5
min., 3 – standby after 10 min., 4
– standby after 15 min.
Stage of calculator key back-light in Calcu- 0 – off, 1 – on, 2 – blinking
lator mode
Stage of calculator key back-light outside of 0 – off, 1 – on
Calculator mode
Flag 7 - Limit and value of the percent add-on
You can shift from limit to value programming by pressing the (Subtotal) button. The
directional arrow shows either limit or value, whichever is actually programmed.
Digit
Default setting
Meaning
Valid values
Left
00
Limit for the percent add-on entered during
sale
00–99
Right
0000
Programmed percent add-on value (to set value of 10 enter 1 0 0 0)
0000–9999
<
Figure 3.7
Seven system
flag values..
21
Euro-2100
© Elcom, s. r. o.
Programming manual
Flag 8 - Limit and value of the percent discount
You can shift from limit to value programming by pressing the (Subtotal) button. The directional arrow shows either limit or value, whichever is actually programmed.
Figure 3.8 >
Eighth system
flag values..
Digit
Left
Right
Default
setting
00
0000
Meaning
Limit for the percent discount entered during sale (00 – 99)
Programmed percent discount value (to set
value of 15 enter 1 5 0 0)
Valid values
00–99
0000–9999
Flag 9 - Time setting
Figure 3.9 >
Ninth system
flag values..
Digit
1&2
3&4
D e f a u l t Meaning
setting
12
Hours setting
00
Minutes setting
Valid values
00–23
00–59
Flag 10 - Date setting
The cash register handles leap years and adjusts the number of days in each month automatically.
Figure 3.10 >
Tenth system
flag values..
Digit
Default
ting
set- Meaning
Valid values
1&2
01
Day
01–31
3&4
01
Month
01–12
5&6
01
Year
00–99
Extended flags programming
In the programming mode select the bar-code flags programming by pressing (Credit).
figure 3.11 >
Digit
Default setting Meaning
Extended
flags values
22
1
0
2
0
3
0
4
0
5
0
Valid values
0 – look-up using the entire
bar-code, 1 – as option 0, but
Look-up algorithm for PLUs when reading
if look-up fails, the bar-code
18-digit long bar-code
is considered EAN 13+5 and
look-up ignores extension
0 – look-up using the entire
bar-code, 1 – as option 0, but
Look-up algorithm for PLUs when reading
if look-up fails, the bar-code
15-digit long bar-code
is considered EAN 13+2 and
look-up ignores extension
Printing format and storage format in PC
0 – do not store and print
journal if ECR reads and successfully looks
anything, 1 – print and store
up the 13+5 bar-code
only bar-code extension,
Printing format and storage format in PC
2 – print and store entire barjournal if ECR reads and successfully looks
code
up the 13+2 bar-code
Printing format and storage format in PC
journal if ECR reads and successfully looks
0 – do not store and print
up bar-code with other length than 15/18
anything, 1 – print and store
or if a PLU has been read using the PLU
entire 18-digit long code
number that has length 15/18 and ECR
programmed
database contains the same EAN code with
for given PLU
given length (i. e. it is not considered an
EAN 13+2/13+5 code)
Euro-2100
Programming manual
© Elcom, s. r. o.
Tax rates programming
The cash register allows the use of six tax rates
name can contain up to ten standard width
plus one rate without tax. Both the tax rate and
characters.
its name are programmable. The seventh rate is 6) Enter the tax level name and press (Subtotal) key. For instance, if the tax level
not programmable.
name is VAT 19, you will enter following
key sequence: $, , 2 × ,
A tax rate consists of two programmable data:
/, 7 × 1, 6 × 9, 4 × 7. Enter capital
letters by pressing the (Shift) key and
1) tax rate (0, 19…)
the corresponding letter. You can continue
2) tax name (TAX, VAT, TAXABLE…)
to programme the remaining tax levels.
7) To exit the tax level programming, press
Tax level programming procedure:
(Total) key.
1) witch the ECR into programming mode
“P” by pressing .
2) Press the key. The display shows More details on entering texts are located at the
the number of programmed tax level and end of this chapter.
its rate.
Correction of the tax level values
19.00%
1
TAX RATE
1) Switch to the “P” mode by pressing
.
2) Enter the number of the tax level you want
to edit and press the (Refund) button.
3) Re-programme the parameters as described
in above section.
4) You can print the newly programmed tax
level values by pressing (Check) key.
5) Finish the corrections by pressing the (Total) key.
3) Enter the tax rate without decimal point.
First two numerals compose integer part of
the rate, last two compose decimal part (i.
e. for tax rate of 19 it is 1 9 0 0). The tax
rate can be changed only after daily and periodical report have been executed in “Z”
report mode. If you need to disable a specific tax level, programme its tax rate as 100
or higher.
Printing of the preprogrammed
4) Press the (Subtotal) key. Display will
tax values
show label for programming the tax level
To verify the programmed values, print them
name (or label).
by pressing the (Check) button in the tax
5) After the tax rate programming is finished, programming mode. If working in another
the display will show the name of currently programming mode, press the (Reund)
programmed tax level in the first display key and then the (Check) key. It is possibrow (VAT 19, TAX 10…) and its num- le to print the rate and name of a particular tax
ber in the second display row. The tax level level by pressing the (Ean) button.
Receipt logo programming
The Euro-2100 can print up to nine lines of 3) The notification „1 LOGO LINE“ appetext at the beginning of the receipt (e. g. “Royars in the first display row and informs you
’s Food Store”, “Thank you” etc.) Euro-2100
that you are programming the first line of
can have on each line up to 24 normal sized/12
the logo and the second display row will
double sized characters.
show the currently programmed text for
that row. Enter new data for the current
Logo programming procedure
logo line. If you mistype or make a mistake,
you can delete previous characters by pres1) Switch the ECR to “P” mode by pressing
sing (Clear) key. Programmed text
will be printed out just as typed in, starting
.
from the left.
2) Press the (Po) key.
23
Euro-2100
© Elcom, s. r. o.
Programming manual
3) Re-programme with corrected value as
shown in section above.
4) You can print out the entire logo by pres1
sing (Check) key; print out the current line by pressing (EAN) key.
4) Press the (Subtotal) key. The next
line will appear on the display and be ready 5) Finish corrections by pressing the (Tofor editing.
tal) key.
5) Press the key to finish the programPrinting the programmed logo
ming of receipt logo lines.
Euro-2100
Logo line
Correction of the logo lines
lines
Programmed logo lines can be printed in
1) Switch the ECR to “P” mode by pressing programming mode by pressing the (Check) key. Print a particular programmed
%.
2) Enter the line number you want to correct line by pressing the (EAN) key.
and press (PO).
Cashier programming
The programming of cashiers consists of three 4) Finish the cashier name programming by
steps:
pressing (Subtotal) key. The ECR
shows the current cashier number in the
• cashier’s name
first display row, together with the label
• cashier’s password
(“PASSW”) that indicates programming
• cashier’s authorisation
of cashier password. Press (Total) to
The ECR allows for up to six cashiers. This
finish the programming procedure (next
programming allows you to assign a password
steps will not run).
to each cashier, which will be used by him/her
to log into the ECR and use its functions. This
0001
password will also identify the cashier on the
1
CASH.
PSWD
ECR: the receipts issued by that cashier are
identified by his/her name and all operations
are assigned to him/her.
5) Enter the cashier’s password. The password
is composed by the up to four numerals.
Programming procedure:
If you mistype during entering of the password, you can use (Clear) key to cor1) Switch the ECR to “P” mode by pressing
rect
your mistakes.
.
%
2) Press the (Password) key. Display 6) Finish the programming of cashier’s password by pressing (Subtotal) key. The
will show the current cashier number and
ECR will then show the current cashier
label “NAME” in the first display row which
number in first display row along with label
indicates you are programming the cashier’s
(“ACCESS”) that indicates programming
name. Second display row contains the curof cashier’s authorisations for ECR morent cashier’s programmed name.
des. Press (Total) to finish the enti3) Enter the name for the current cashier.
re programming procedure (next steps will
CASHIER1
not run).
1
CASH NAME
1111
CASH. ACCES
Cashier name can have up to ten charac1
ters. If you mistype or make a mistake while entering text, you can use a (Clear)
key to delete recent characters. See the end 7) Programme the mode access flags according
to the table 3.11. If you mistype, correct
of chapter on hint on entering texts.
24
Euro-2100
Programming manual
2) Enter the number of the cashier you wish << Figure 3.11
Cashier access rights.
to correct and press (Password)
key.
Access to the “Z” mode:
0–no
3) Continue in the same way as when program1–yes
ming other cashiers.
Access to the “P” mode:
4) You can print out data on all cashiers by
Access to the “T” mode:
pressing (Check) key; press key to
print out data on the current cashier only.
your mistakes using (Clear) key.Warning: you cannot deny access to program- 5) Finish the corrections by pressing (Toming mode “P” for the cashier no. 1.
tal) key.
Press the (Subtotal) key to continue
Printing of Cashier values
programming of the remaining cashiers;
continue with step 3. If you press (Total) key, you finish the programming pro- To check the programmed names and other
cedure for the cashiers.
settings, press the (Check) key in the
cashier programming. If in the programming
Correction of cashiers
mode, press the (Password) key first
and then press (Check) key. Print the
Switch the ECR to “P” mode by pressing programmed values of the current cashier by
pressing the (EAN) key.
%.
Digit
Access authority 1111
1
Access to the “X” mode:
2
3
4
8)
1)
© Elcom, s. r. o.
Function text programming
The Euro-2100 allows you to programme all
function text in the first display row and
the operation labels that can be displayed/princontents of that text in the second display
ted to the receipt. The default values for all
row.
function texts are shown in the table 3.12. You 3) Enter new function text that could have up
to 17 characters. If you mistyped, you can
can adjust all of them to your needs.
correct mistakes by pressing (Clear)
key. Details on entering texts are located at
Function text programming procedure:
the end of this chapter.
1) Switch the ECR to “P” mode by pressing 4) Press (Subtotal) key to programme
next available function text; continue with
%.
step 3). Finish the function text program2) Press the (Void) key. ECR will display
ming by pressing (Total) button at
the number of the currently programmed
any time.
CASH
1
Text mo.
1
2
3
4
5
6
7
8
9
10
Func.text
Default setting
CASH
CHECK
CREDIT
CHANGE
REFUND
VOID
RA
PO
TOTAL
DOCUMENT NUMBER
Correction of function texts
1)Switch the ECR to “P” mode by pressing
%.
Description
Cash payment denomination
Check payment denomination
Credit card payment denomination
Change value denomination
Refund value denomination
Void denomination
Received on account denomination
Paid out denomination
Total value
Document number
<
Figure 3.12
Default
function texts.
25
Euro-2100
© Elcom, s. r. o.
2) Enter the number of text to be corrected
and press (Void) key.
3) Continue in the same way as when
programming function texts (consult section above).
4) Print out all programmed function texts by
pressing (Check) key; print the currently edited function text by pressing (EAN) key.
5) Correction of function texts is finished by
pressing Total button.
Programming manual
Printing function texts setting
To check the programmed function texts, press
(Check) key in function text programming mode. If in programming mode, press
(Void) key first and then the (Check)
key. Print the value of a particular function text
by pressing (EAN) key.
Departments programming
The Euro-2100 cash register has 30 depart- 3) Enter the new department price (maximents (DPT) available. Each department has
mum eight digits, including decimals). If
three basic components:
you mistype, you can correct your mistakes
by pressing (Clear) key.
1) Price
4) Press (Subtotal) key to continue with
2) Department flag
programming the flags for the current de3) Name
partment. The display shows current department number in the first display row
Programming procedure:
together with label (“FLAG”) to indicate
department flag programming. The value
1) Switch the ECR to “P” mode by pressing
of department’s flags are shown in the second display row. Press (Total) key to
%.
2) Press the (DPT). key. The current destop department programming (next steps
will not run).
partment number and the label (“PRICE”) appear in the first line on the display
to indicate department price programming.
00038
The programmed price appears in the se1
cond display row.
DPT flag
0.00
1
Figure 3.13 >
Digit
Cashier
access rights
26
Default
setting
DPT price
5) Enter the department flags for the current
department according to the table 3.13. If
Meaning
Valid values
0 – no tax , 1 – tax level 1, 2 – tax
level 2, 3 – tax level 3, 4 – tax level
4, 5 – tax level 5, 6 – tax level 6
0 – normal, 1 – single item department
0 – no, 1 – yes
0 – sale forbidden, 1 – open price (manually entered price), 2 – fixed price (preprogrammed price),
3 – 1+2 (preprogrammed price or
the possibility to enter a price manually)
1
0
Assigning VAT level to a department
2
0
Type of department
3
0
Negative department
4
3
Sale feature
5
8
HALO limit, maximum 8 (maximum num0–8
ber of digits allowed)
Programming manual
Euro-2100
© Elcom, s. r. o.
Correcting departments
you mistype, you can correct using the (Clear) key
6) Press (Subtotal) key to continue with 1) Switch the ECR to “P” mode by pressing
programming the name for the current de%.
partment. The ECR display shows current 2)Enter the number of the department you
department number along with the label
want to adjust (1–30) and press h (DPT)
(“NAME”) in the first display row; second
key. or press the selected department button
display row contains the assigned tax level
to directly choose required department.
3) Continue re-programming desired values
as shown in the section above.
DPT01
4) You can print out all the programmed de1
partment values by pressing ((Check)
key; to print out the currently programmed
on the left and current department name
department, press (EAN) key.
on the right.
5) Finish the corrections by pressing (To7) Enter the department name. If you mistytal) key.
pe, you can correct your mistakes by presPrinting department values
sing (Clear) to delete characters. See
the end of chapter for more detailed instructions on entering texts.
Check the programmed department values
8) Press the (Subtotal) to continue de- by pressing the (Check) key in the department programming for next depart- partment programming mode. If in another
ment; proceed to step 3). The program- programming mode, press the direct button
ming of departments can be finished at any of a department or a department number and
time by pressing (Total) key.
then press the h (DPT) button. Afterwards
press the (Check) button. To print the
settings of currently programmed department,
press the (EAN) key.
DPT name
Sale unit programming
Sale unit can be assigned to each PLU and represents the unit in which the PLU is sold. It is
possible to programme eight sales units of up
to three characters each. Table 3.14 shows the
default settings for sale units; you can adjust
these defaults to your needs.
Sale units programming procedure:
Digit
1
2
3
4
Message
PCS
kg
l
Digit
5
6
7
8
Message
m
m²
btl
pkg
consult the section on entering texts at the
end of this chapter.
1) Switch the ECR to “P” mode by pressing 4) Press (Subtotal) key to continue sale
units programming with the next sale unit.
%.
Finish sales unit programming at any time
2) Press the (Surcharge) key. The
by pressing the (Total) key.
ECR display shows the current sale item
number and its name in the second row.
Correcting programmed sale
3) Enter the text for the current sale unit (up
units
to three characters). You can correct mistypes by pressing (Clear) key and/or
1) Switch the ECR to “P” mode by pressing
%.
2) Enter the number of the sales unit you want
to modify and press (Surcharge)
1
key.
<
Figure 3.14
Default
sale units.
sale unit
27
Euro-2100
© Elcom, s. r. o.
3) Continue the programming as described in
the previous section (see above).
4) You can print out all programmed sale units
by pressing (Check) key; to print the
currently programmed sale unit, press (EAN) key.
5) Finish the corrections by pressing (Total) key.
Programming manual
If you want to check the settings of the sale
units, press the (Check) key in the sale
unit programming mode. If the ECR is in the
root programming mode, first press the (Surcharge) key, then the (Check) key. For
a printout of the current sale unit, press the (EAN) key.
Printing sale unit settings
Article items (PLU) programming
The article item is referenced as PLU (Price Look-Up) throughout this document. The
Euro-2100 cash register has up to 8 000 PLUs
available. The PLU has five basic programmed
components:
1)
2)
3)
4)
5)
PLU price
PLU 1st flag
PLU 2nd flag
PLU name
PLU bar code
ber and label (“FLAG1”) in the first display row and current value of the group of
flags in the second row. Press (Total)
to leave PLU programming (next steps will
not run)
001000
1
If you set up an article item as descriptive, that
item shows its name when sold, but it doesn’t
include any sale data (its quantity/value doesn’t
count in quantity/value of sold items).
Programming procedure:
PLU flag1
5) Enter the data for the first group of PLU
flags; orient yourself by the table 3.15. Correct mistypes by using (Clear) key.
PLUs within 1001–1015 mustn’t be assigned
to a negative department.
6) Press (Subtotal) to continue with
programming of second group of PLU
flags. The display will show current PLU
number and label (“FLAG2”) in the first
display row and current value of the group
of flags in the second row. Press (Total)
to leave PLU programming (next steps will
not run)
1) Switch the ECR to “P” mode by pressing
%.
2) If you wish to programme a PLU with a
specific number, enter that number now
and press (PLU) key. If you don’t supply any number, the ECR starts program001018
ming from the first PLU. The ECR display
1
shows the current PLU number and label
(“PRICE”) that indicates programming of
7) Enter the data for the second group of PLU
the PLU’s price.
flags; orient yourself by the table 3.15. Correct mistypes by using (Clear) key. No
0.00
PLUs can link to the PLUs within 1001–
1
1015.
8) Press (Subtotal) to continue with
3) Enter the price for the programmed PLU;
name programming for the current PLU.
maximum eight numerals, including deThe display shows current PLU number
cimals. You can delete mistyped numerals
and label (“NAME”) in the second display
using (Clear) key.
row and the assigned tax level (left) and
name (right) in the first display row. Press
4) Press (Subtotal) to continue with
programming of first group of PLU flags.
(Total) to finish the PLU programThe display will show current PLU numming (next steps won’t run).
PLU flag2
PLU
28
price
Euro-2100
Programming manual
Digit
Default
setting
<
Meaning
Valid values
Assigning a VAT level to the PLU
0 – no tax, 1 – tax level 1, 2 – tax level
2, 3 – tax level 3, 4 – tax level 4, 5 – tax
level 5, 6 – tax level 6
1 – 30
0 – no, 1 – yes
0 – normal PLU, 1 – single item PLU
0 – PLU forbidden, 1 – open price (manually entered price), 2 – fixed price
(preprogrammed price), 3 – 1+2 (preprogrammed price or the possibility to
enter a price manually)
1
0
2,3
4
5
01
0
0
Assigning a department to the PLU
Descriptive PLU
Type of PLU
6
0
Sale feature
1
© Elcom, s. r. o.
PLU name
Figure 3.15
First group of PLU
flags.
0000000000000000000
1 PLU barcod
9) Enter the PLU name/description, maxibe connected to ECR and properly confimum 20 characters (or 10 double width
gured). You can correct mistypes using characters). Consult end of this chapter on
(Clear) key.
how to enter texts. You can correct misty- 12) Press (Subtotal) key. If you entered a
pes by using (Clear) key.
bar-code that is already assigned to a PLU,
the ECR will hint you on this by displaying
10) Press (Subtotal) key to continue with
“BARCODE” along with the PLU number
programming of the bar-code for the curof the PLU that bar-code is assigned to.
rent PLU. The display shows the current
PLU number and label (“BARCODE”) in 13) After the bar-code has been successfully assigned, the ECR continues with programthe first display row and the currently assigming of next PLU; proceed to step 3). Press
ned bar-code in the second row. Press (Total) to finish the PLU programming
(Total) to finish the PLU programming. After the PLU programming is over,
(next steps won’t run).
the ECR will sort all the bar-codes and in11) Enter the PLU bar-code either using the
dicates that it’s doing so on its display. If
keyboard or using a scanner (scanner has to
Digit
Default
setting
1, 2
00
3
1
4
0
5
1
6
1
7
8
<
Meaning
Valid values
Assigning the sale of another PLU to the 00 – no linked PLU, 01 – PLU
sale of an actual PLU (linked PLU)
No. 1001 is linked, 02 to 15 – PLUs
1002-1015 are linked
Sales unit assigning
1 – The first sales unit assigning,
2 to 8 – assigning the sales unit 2
–8
PLU stock information on PLU report
0 – no, 1 – yes
PLU sale possibility even if stock is nega0 – no, 1 – yes
tive
Split pricing possibility
0 – no, 1 – yes
HALO limit, maximum 8 (maximum num0–8
ber of digits allowed)
Figure 3.16
Second group of PLU
flags.
29
Euro-2100
© Elcom, s. r. o.
BAR CODE DUPLICATE
3 PLU barcod
3. PLU
3
PLU barcod
Programming manual
1) Switch the ECR to “P” mode by pressing
.
2) Enter the PLU number and press the (Price) button. If you don’t enter any
number, the ECR will start form PLU no.
1. The PLU number and the label (“PRICE”) appear in the first display row, current
PLU price is displayed in the second row.
the ECR is disconnected from power, it
will resume sorting after turned on again.
0.00
1
PLU
price
CODE SORTING
3) Enter the new price (maximum eight digits
including decimals).
4) Press (Subtotal) key to continue in the
Setting up the bar-code scanner
price programming of the next PLU; proceTo secure a reliable functioning of bar code
ed to step 3). Press (Total) key to finish
scanning it is important to program the scanthe quick PLU price programming.
ner correctly and connect it properly to the
Quick PLU stock programming
cash register. Parameters of the bar code scanner setting:
The cash register also records stock informa• eight data bits
tion for each PLU. The PLU stock informa• none parity
tion can be changed to another value directly,
• one stop bit
or you can alter stock by operations in the re• transmission speed and terminal character gistration mode.
is according to setting of the fifth register
system flag
1) Switch the ECR to “P” mode by pressing
.
The default setting of flag no. 5 corresponds to 2) Enter the PLU number and press the Metrologic bar code scanners (MS 951, MS 6720,
(Scales) key. If you didn’t enter any numMS 7100, MS 860, MS 6130 and MS 9520). All
ber, the ECR will start from PLU no. 1. The
you have to do is read the following bar codes
display shows current PLU number and lafrom the scanner programming manual:
bel “STOCK” in the first display row and
the current stock for that PLU in the se1) Enter/Exit
cond row.
2) Recall Default
3) Enter/Exit
0.000
PLU stock
1
The ECR is able to handle bar codes containing data for product weight. The format is
the following: PP XXXX V MMMMM K; PP 3) Enter stock value (up to nine digits, to three
- prefix of bar code (28 or 29), XXXX - PLU
decimal places) and press:
number (0001-2400), V - scales check digit,
• (Subtotal) key to apply the
MMMMM - product weight (3 decimal digits)
entered number as the new stock
and K - bar code check digit.
value,
• (Surcharge) key to add
Quick PLU price programming
the entered number to the current
stock or
If you need to change only the prices of seve• (Discount) key to subral PLUs, you can easily do it by the following
tract the entered number from the
procedure:
current stock.
30
Programming manual
Euro-2100
© Elcom, s. r. o.
Maximum stock value is 999,999.999. If 4) You can print out all programmed PLUs
you enter integer amount, enter the numby pressing (Check) key or you could
print out the currently programmed PLU
ber and just press . After pressing any of
by pressing (EAN) key.
the above three keys, the ECR will continue with programming of the stock for the 5) You can jump to any PLU using the procedure in step 2). Press (Total) key to
next PLU.
4) Press (Total) to finish the quick PLU
finish correcting the PLUs.
stock programming.
Printing the programmed PLUs
Correction of programmed PLUs
1)Switch the ECR to “P” mode by pressingw
%.
2) Enter the PLU number and press the (PLU) button. You can analogously use the
bar-code scanner: if you are outside PLU
name programming, scanning the bar-code
will jump to the said PLU.
3) Continue programming the PLU values as
described in the relevant section.
To verify programmed values, print them by
pressing the (Check) key in the PLU
programming mode. If the cash register is in
root programming mode, press the (PLU)
key and then the . (Check) key. Only PLUs
that have been programmed will be printed. It
is possible to print the programmed value of a
particular PLU by pressing (EAN) key.
Programming the euro currency
1EUR=1GBP
The Euro-2100 allows you to use the euro currency. Because of the stage of the euro currency
implementation, it is also possible to register in
the national currency (stage no. 1 and no. 2) or 4) Enter the exchange rate for euro (eleven
in a foreign currency (stage no. 3). Registration
digits maximum, with four decimals); miwith the euro is divided into four stages:
nimum rate is 0.000 1 and maximum is
10,000. Press (Subtotal) key.
Stage without euro currency
5) Enter the currency flags (two digits). First
digit determines to how many decimal plaThe cash register works without the Euro. All
ces amount in euro will be displayed. Second
transactions are performed in the national curdigit determines to how many decimal plarency.
ces will the price in euro be rounded.
Curr. rate
First euro currency stage
After programming, the information on transition into first stage of euro currency is disIn the first euro stage the master currency is played. The same information is also printed
the national one, the secondary currency is the out along with information on values entered
euro. The customer can pay either in the natio- during the transition.
nal currency or in euro. Going back to the stage without euro isn’t possible without resetting During the first euro stage the actual exchange
the ECR. Call your service technician.
rate can be set by the following procedure:
Procedure for entering the first euro
stage:
1) Switch the ECR to “P” mode by pressing
%.
2) Press the (Drawer) key.
1) Switch the ECR to “P” mode by pressing 3) Enter the current euro exchange rate and
press (Subtotal Total) key sequence.
%.
2) Enter the code by pressing
Second euro currency stage
.
3) Enter the acronym for the national currency (three characters maximum) and press In the second euro currency stage the master
currency is euro, the secondary one is the nati (Subtotal) key.
31
© Elcom, s. r. o.
Euro-2100
Programming manual
onal currency. The customer can pay either in 4) Enter the exchange rate for euro (eleven
euro or in the national currency. ECR grand
digits maximum, with four decimals); mitotals will be erased by transition into second
nimum rate is 0.000 1 and maximum is
stage. The transition is possible only if dai10,000. Press (Subtotal) key.
ly and periodical report in “Z” mode are per- 5) Enter the currency flags (two digits). First
formed. Reversal into first euro currency stage
digit determines to how many decimal plais impossible without resetting the ECR. Call
ces amount in secondary currency will be
your service technician.
displayed. Second digit determines to how
many decimal places will the price in seProcedure for entering the second euro currencondary currency be rounded.
cy stage:
After programming, the information on tran1) Switch the ECR to “P” mode by pressing sition into third stage of euro currency is displayed. The same information is also printed
%.
2) Enter the code by pressing 2002 . out along with information on values entered
3) Enter the exchange rate for euro (eleven during the transition.
digits maximum, with four decimals); minimum rate is 0.000 1 and maximum is During the third euro stage the actual exchange rate can be set by the following procedure:
10,000. Press (Subtotal) key.
After programming, the information on transi- 1) Switch the ECR to “P” mode by pressing
tion into second stage of euro currency is dis%.
played. The same information is also printed 2) Press the (Drawer) key.
out along with information on values entered 3) Enter the secondary currency acronym (up
during the transition.
to three characters) and press (Subtotal) key.
During the second euro stage the actual exchan- 4) Enter the current euro exchange rate and
ge rate can be set by the following procedure:
press (Subtotal) key.
5) Enter currency flags (see above) and press
1) Switch the ECR to “P” mode by pressing
(Subtotal Total) key sequence.
%.
Entering texts into ECR
2) Press the (Drawer) key.
3) Enter the current euro exchange rate and
press (Subtotal Total) key sequ- The numerical keys are used in text programence.
ming (logo, PLU names, cashier names etc.).
There are numbers in the upper part of the keys
Third euro currency stage
and letters and other characters are in the lower
part. In national versions, all letters and characThe master currency is the euro, the secondary ters of the alphabet are on the keys. To enter a
currency is any foreign one. The customer can capital letter hold the # (Shift) key and press
pay either in euro or in the secondary foreign the relevant key. For instance, enter letter “a” by
currency. Reversal to second euro stage is not simply pressing the key, letter “F” by holpossible without resetting the ECR. Call your ding $ and pressing the
key thrice 2,
service technician.
number “5” by pressing the key four times,
to get the space character press /.
Procedure for entering the third euro currency stage:
Characters that are not printed on the keys are
„’“ (2 × ), „;“ (3 × ), „<“ (4 × ), „>“ (5 ×
1) Switch the ECR to “P” mode by pressing ), „=“ (6 × ), „?“ (7 × ) a „$“ (8 × ).
%.
2) Enter the code by pressing 2003 . If you want to print a double-spaced charac3) Enter the acronym for the secondary fore- ter, press the key before each doubleign currency (three characters maximum) -width character. The double-width character
and press (Subtotal) key.
is displayed as space on the ECR display. If the
programmed text string has characters which
32
Programming manual
are on the same key, press the particular key as
needed, wait until a full character appears on
the display, and then press the key again. If there are successive characters that belong to different keys, simply press the buttons in order
without waiting. Mistakes caused when entering characters can be corrected by a key to
clear the incorrect characters and continue.
Euro-2100
© Elcom, s. r. o.
"#$
!
<
Figure 3.1
Keyboard
layout.
Numeric keys
Programming of programmable keyboard keys
This procedure describes how to programme
the programmable ECR keys. An individual key could be programmed with arbitrary
keystroke sequence (function keys, up to 16)
that will be generated when the programmed
key is pressed in the future.
further function keys to the programmable sequence or press the currently progammed key to finish programming and assign
the programmed function sequence to that
key. The ECR will update the key definition and print the change information messages to both receipt and journal (this inThe programming of keys starts in programming
formation includes programmed key ID
mode. Press the key you wish to programme.
number, record type „01.Key“, info label on
function programming and its number „01.
1. The display shows the ID number of
Function“ and the programmed function
programmable key, the label „KEY NAME“
sequence). The ECR then continues with
and the current value assigned to that key.
programming of next key, or goes to the
2. Enter a new name and confirm by presfirst key if the currently programmed key
sing the (Subtotal) key. If you press was the last one.
(Subtotal) key without entering anything, 6. If you didn‘t enter the key programming
you just confirm the previous assigned vamode, then you can press (Subtotal) to
lue. When you press (Total), the key
confirm the current value and proceed to
the next key (or the first key if you were
programming procedure ends.
on the last key) and the programming pro3. If you have changed name for the programcedure continues again with step 1.
med key, the ECR will update its settings
and print the information on key name 7. Press (Total) button to exit the programchange on the receipt (ID number of
ming mode.
programmed key and the data on changed
Deleting the key function
parameter -- label „Key name“ and its newly programmed value).
4. The display will then show the number You can delete function sequece assigned to a
ID of the programmable key, information key if you press (Void) key during step 4 of
label for the function programming „01. the programming procedure.
Function“ and text description of the current key function.
The display will show that you are about to de5. Press „MULTIPLY“ key to enter the key lete the function sequence assigned to a key and
programming mode. The display will ask awaits a confirmation. Press (Void) key to
you to press a key. By pressing a function delete the value or press (Subtotal) to cankey (any key from the right part of the cel the deletion. When you cancel the deletion
keyboard), you‘ll assign its value to the you can proceed with programming procedure
programmed key. Keep pressing to add as usual. If you decide to confirm deletion, the
33
© Elcom, s. r. o.
Euro-2100
ECR will delete the assigned function sequence assigned to that key and prints the information on the deleted function (this information
includes programmed key ID number, record
type „01.Key“, info label on function programming and its number „01.Function“ and the
keyword „deleted“). The programming procedure then continues normally.
Printing of the programmed key name
Programming manual
The ECR will print to both receipt and journal
following information on the key: ID number
of the programmed key and record type „01.
Key“, parameter label „Key name“ and current
value assigned function sequence.
Printing the settings for all keys
You can print the setting for all ECR key if you
press (Cheque) key in either step 1 or step
4 of the programming procedure.
The name of the programmed key will be printed if you press (EAN) key during step 1 of The display will show „Keyboard prog.“ label
and the same will be printed to both receipt
the programming procedure.
and journal. For each key, the ECR will print:
The ECR will print to both receipt and journal
following information on the key: ID number - number ID and record type: „01.Key“
of the programmed key and record type „01. - parameter label „Key name“ and the name
Key“, parameter label „Key name“ and current
of the current key
value of that parameter.
- for each function in the current key‘s assigned function sequence will print number
Printing of the programmed key function
and label „1.Fucntion“ and the current value of that function and the programming
The name of the programmed key will be prinof the keys finishes.
ted if you press (EAN) key during step 4 of
the programming procedure.
34
Registration mode
Euro-2100
© Elcom, s. r. o.
Operation in registration mode
The functions that are described in the following chapters are used in the registration
mode. All financial transactions are stored in
this mode.
If the cash register allows you to use the training mode, you can try the following functions
in the training mode first (sales data are not
stored in the memory).
Recommended procedures at the beginning of the day
1) Check if there is enough paper on the prinb) a daily report was executed.
ter roll for the day. Insert a new paper roll, 3) Check whether there is enough cash in
if necessary.
drawer.
2) Print out an “X” report and make sure 4) Register the initial cash put into the drawer
that:
by pressing the (RA) key.
a) date and time are correct,
Printing modes
The Euro-2100 cash register allows you to cho- 3) High speed
printing saturation is norose a printing mode according to two basic crimal, printing speed is much higher than
teria: printing speed and power consumption.
normal. Power consumption is highest in
One font is included in the Euro-2100; its hethis mode. This mode takes advantage if
sales cadence is high. The discharge of the
ight is 2.5 mm.
internal lead-acid accumulator is much higher than in normal mode, so that the cash
There are three printing modes in Euro-2100:
register can work without external power
1) Normal
normal printing saturation,
supply less time than in normal mode.
normal power consumption. This mode is
set as default.
Programme the sixth system flag to set up the
2) Economical
printing saturation is nor- printing modes.
mal, the printing speed is a little bit lower
than normal. Power consumption is lowest If the cash register is not powered from an exin this mode. This mode allows the longest ternal power source (power adapter, car battepossible use of the cash register without an ry…), printing saturation may be a little lower,
external power supply.
depending on the charge of the internal accumulator.
Status and functions required at the beginning of registration
Error warning: the CLEAR key
If a key is used for two functions, choose the
function in the lower part of the key by simply
pressing the key and choose the function in the If a function key is used incorrectly or the reupper part of key by holding the (Shift) gistration range is exceeded, the machine issues
an error beep and an error message appears on
key and pressing the key.
the display. To recover and correct the condi35
Euro-2100
© Elcom, s. r. o.
tion, simply press the (Clear) key. The error code is cleared from the display. Then enter
the correct function or amount.
Cashier log in: the Password key
The cash register can assign a secret identification number (password) for up to six
cashiers. Cashier passwords, as well as names,
are programmed in the programming mode.
To use the cashier identification function, enter the numeric password and press the (Password) key. For extra security, press the
button before the password entry. Display will show a “PASSWORD” label. The entered password numbers are not visible on the
display at this time. If an incorrect password
is entered, the register beeps twice and remains locked. Enter the correct number and press
the (Password) key to unlock the
cash register. The password protection prevents
unauthorised use of ECR. If the cashier’s name
has been programmed, it will be printed in the
receipt header area after the cashier logs in.
Cashier log out: the (Password)
key
If the cash register has been protected from
unauthorised use, the cashier should log out by
pressing the . (Password) key after finishing registration. Display shows the “PASSWORD” label and the cash register is locked
until the correct password is entered and the
(Password) key is pressed. When the
cash register is locked, registration cannot be
performed and the cash drawer will not open.
This function is used when changing cashiers
or when a cashier leaves the ECR.
Finalizing a transaction: Cash,
Cheque, Credit keys
Pressing one of the payment keys determines
the payment method (by cash, by credit card or
by cheque). Finish the transaction by pressing
one of the following buttons (Cash), (Credit), (Cheque).
Samples of basic registration procedures
Figure 4.1 >>
Sample sale receipt:
1 - receip logo (header),
2 - ECR tax ID number, 3- taxpayer’s identification, 4- weekday,
5- date, 6- receipt number and ECR number,
7- time, 8- cashier
name, 9 - item (PLU)
name, 10 - assigned tax
level, 11 - sold quatity
and value, 12 - total
item sale value.
36
1) Switch the cash register into the “R” mode::
%
2) If needed, enter the password to log in.
3) Enter the PLU codes of the registered
items.
4) Press the (PLU) key.
5) Repeat step 3 and 4 for each PLU.
6) Press the (Subtotal) key. Total amount of the sale (including the VAT value)
appears on the display.
7) Announce the amount to the customer.
8) Enter the amount tendered by customer
and press the corresponding payment button: (Cash), (Cheque), (Credit).
9) The cash drawer opens. When the amount
tendered is greater than the amount due,
the register will show the change. Otherwise your register will show the additional
amount due.
10) Tear off the receipt and give it to your customer together with the change (if any).
1
2
3
4
6
8
10
MONGOOSE
Grocery Store
TPN: 123456789012
UN: 01234567/9876
T H A N K Y O U
Your receipt
08:25:11 Wed.01-03-2006
01*0005
Smith
Bread
A
1*2.40
=2.40
Roast coffee
A
2*33.00
=66.00
Fruit tea
A
1*10.20
=10.20
SUBTOTAL
88.20
---------------------TAXABLE VAT5% 78.60
NET VAT5%
74.86
VAT5%
3.74
NET TOTAL
74.86
VAT TOTAL
3.74
TOTAL
78.60
-----------------------CASH
78.60
5
7
9
11
Euro-2100
Registration mode
© Elcom, s. r. o.
Registration using departments
Step
To get better information about revenue of
particular items, split the articles into departments (article groups). The “department” means articles grouped in the same category (such
as dairy products, pastry, alcohol etc.), or of
the same tax level (VAT 16, TAX 10 etc.).
The Euro-2100 cash register enables the use of
a maximum of thirty departments and, if PLUs
are used as sub departments, the number increases up to 2,100.
1.
2.
3.
4.
Press
"
Department 7
A
1*27.00
=27.00
Department 10
A
1*31.20
=31.20
SUBTOTAL
58.20
---------------------TAXABLE VAT5% 58.20
NET VAT5%
55.43
VAT5%
2.77
NET TOTAL
55.43
VAL TOTAL
2.77
TOTAL
58.20
-----------------------CASH
58.20
Item registration is finished by pressing the
proper department key – . Departments are implemented so as to, after pressing
a department key, the registered amount, the
corresponding tax group, the maximum registration amount, a pre-programmed price and
others parameters are assigned to the revenue
of the department. The sale information is stored in the register memory and utilised for department reports.
Numeric keys – $ and department keys
– are used for registration (see keybo-
DEPARTMENT 7
27.00
ard picture). It is possible to register through
1
departments by entering the department number and pressing the (DPT) key ( , • Using the direct
…). Thus, you can register any de – partment. It is also possible to register departments 1 to 10 by pressing a department key
Step
Press
– .
Basic registration using departments
The ECR can be programmed to use pre-programmed price or the price entered from
the keyboard during registration using departments. If both types are allowed, the cash register will use the price entered from the keyboard.
Registration using departments with
price entry using keyboard
•
Using the (DPT) key
"
1.
2.
3.
4.
department
"
keys
Department 1
A
1*24.00
=24.00
Department 2
A
1*31.20
=31.20
SUBTOTAL
55.20
---------------------TAXABLE VAT5% 55.20
NET VAT5%
52.57
VAT5%
2.63
NET TOTAL
52.57
VAT TOTAL
2.63
TOTAL
55.20
-----------------------CASH
55.20
37
Euro-2100
Registration using departments with
pre-programmed price
© Elcom, s. r. o.
Registration mode
Registering multiple items using
departments
Example: The pre-programmed price for DPT It is not necessary to enter the price repeatedly if more than one of the same item are being
1 is 7.50 and for DPT 2 is 4.20.
sold. After entering the unit price, just press
the corresponding DPT key repeatedly for the
• Using the (DPT) key
number of items sold.
Step
Press
1.
2.
3.
4.
•
Using the direct
– Step
1.
2.
Department 1
A
1*7.50
=7.50
Department 2
A
1*43.20
=43.20
SUBTOTAL
50.70
---------------------TAXABLE VAT5% 50.70
NET VAT5%
48.29
VAT5%
2.41
NET TOTAL
48.29
VAT TOTAL
2.41
TOTAL
50.70
-----------------------CASH
50.70
3.
Using the direct
– Step
Press
1.
2.
3.
4.
department
Department 1
A
1*7.50
=7.50
Department 2
A
1*43.20
=43.20
SUBTOTAL
50.70
---------------------TAXABLE VAT5% 50.70
NET VAT5%
48.29
VAT5%
2.41
NET TOTAL
48.29
VAT TOTAL
2.41
TOTAL
50.70
-----------------------CASH
50.70
•
Press
Using the (DPT) key)
Step
2.
keys
3.
Press
h
h
!
Department 16
A
1*31.20
=31.20
Department 16
A
1*31.20
=31.20
Department 16
A
1*31.20
=31.20
Multiplying items during registration using departments
•
Multiplication of items with price entered
via keyboard
The customer buys 12 pieces of the same items
at 16.20:
Step
1.
2.
resp.
38
keys
Department 2
A
1*31.20
=31.20
Department 2
A
1*31.20
=31.20
Department 2
A
1*31.20
=31.20
1.
•
department
Press
! ( ! )
Euro-2100
Registration mode
Department 2
A
12*16.20
=194.40
© Elcom, s. r. o.
Department 2
A
3/5*31.20
=18.70
•
Multiplication of items with pre-program- • Fractional entry with pre-programmed price
med price
Example: The price is determined for a packing
Example: The customer buys 12 pieces of the that includes five pieces of the item (e. g. a box
same item with pre-programmed price of of processed cheese). The customer buys only
14.20:
three pieces, paying three fifths of the price of
the whole box.
Step
Press
Step
Press
1.
1.
2.
2.
resp.
( )
3.
Department 2
A
resp.
( )
12*16.20
=194.40
Department 2
A
3/5*22.50
=13.50
This feature helps when you need to enter a
large amount of items or you need to enter quDouble multiplication of items
antities that contain decimals (1.5, 0.125, etc.).
Multiplication of numbers with a decimal
during registration using departpoint is often used for weighed items (meat,
ments
vegetables, salads, etc.) where the unit price is
known (e. g. for 1 lb, for 1 litre, etc.). The lar- The cash register can be programmed for doubgest allowed multiplicand is 9,999.
le price multiplication. The function is practical, for example, when entering a sale of items
Registering fractions of items
sold by area (square metres). This function
must be programmed by setting the second sysusing departments
tem flag, digit no. 6 to 1.
The cash register can be programmed for registration of split prices. This functionality is • Double multiplication with entering the
price via keyboard
programmed by setting the second system flag,
digit no. 6 to 0.
Example: The price is determined for a squa• Fractional entry with entering the price via re metres. Your customer buys a 3 by 5 metres
piece.
keyboard
Example: The price is determined for a packing that includes five pieces of the item (e. g.
a box of processed cheese). The customer buys
only three pieces, paying three fifths of the price of the whole box.
Step
1.
2.
3.
resp.
Press
( )
Step
1.
2.
3.
resp.
Press
( )
Department 2
A
3*5*31.20
=468.00
39
Euro-2100
© Elcom, s. r. o.
Registration mode
•
Double multiplication of items with pre- key, the item is automatically registered, the sale
-programmed price
is automatically finished and the cash drawer
is automatically opened. This group is called a
Example: The pre-programmed price is 32.00 single item sale group. In the following example,
determined for a square metre. Your customer DPT 4 is programmed with the price of 5.50.
buys 3 by 5 metres.
Step
Press
Step
Press
1.
2.
3.
resp.
( )
1.
Department 4
A
1*27.00
=27.00
-----------------------TAXABLE VAT5% 27.00
NET VAT5%
22.70
VAT5%
4.30
NET TOTAL
22.70
VAT TOTAL
4.30
TOTAL
27.00
-----------------------CASH
27.00
Department 2
A
3/5*32.00
=480.00
Single item sales using into
departments
Some services often sell a single item (for example, cigarettes). To simplify the sale of such
items, it is possible to programme the price into
a department and set it up as single item sale
department. Then, by pressing the department
( )
If other transactions have already taken place
before a single item sale, the transaction is not
finalised and it is possible to continue with registration of other items.
PLU registration
Articles have assigned codes (PLU numbers).
For example, RAMA butter – PLU no. 5, Skimmed milk - 23, Rum 0.5 l - 189, etc. Data concerning the articles (name, price, assignment to the
department, etc.) are programmed in the cash
register memory and linked to a particular PLU
number. Entering the PLU number and pressing the (PLU) key looks up the data in the
register memory and registers it automatically.
PLU registration allows for storing of information about the sale of each particular item, printing the names of articles automatically on the
receipt, printing the unit price automatically
and assigning the transaction to a department. It
also prevents mistakes in keyboard registration.
The name of each item on the receipt satisfies
the customer for correctness of items purchased.
By automatically calling programmed data from
the cash register memory, faster customer service
and greater accuracy is provided.
PLU registration makes it possible to get a clear
overview of the sale of each particular item. A
personal computer and a bar code scanner can
supplement the advantages of PLU registration.
40
Basic PLU registration
Step
1.
2.
3.
4.
Press
Bread
A
1*27.00
=27.00
Butter
A
1*31.20
=31.20
SUBTOTAL
58.20
-----------------------TAXABLE VAT5% 58.20
NET VAT5%
55.43
VAT5%
2.77
NET TOTAL
55.43
VAT TOTAL
2.77
TOTAL
58.20
-----------------------CASH
58.20
Euro-2100
Registration mode
Bread
1
27.00
Multiplication in PLU registration
Example 1: The customer buys twelve pieces of
the same PLU with the price of 21.40 each.
Step
1.
2.
Press
12
1
Bread
12*21.40
A
=256.80
© Elcom, s. r. o.
and the drawer opened. This PLU is called a
single sale PLU. PLU 4 is programmed with
price 30.80 in the example.
Step
1.
Press
Cigarettes
A
1*70.00
=70.00
-----------------------TAXABLE VAT5% 70.00
NET VAT5%
66.67
VAT5%
3.33
NET TOTAL
66.67
VAT TOTAL
3.33
TOTAL
70.00
-----------------------CASH
70.00
Example 2: The customer buys twelve pieces of Note: If other transactions have already been
the same PLU with entering the price of 20.50 performed before the single item sale, then that
via keyboard.
sale does not complete the transaction. It is
possible to continue registering of other items.
Step
Press
1.
2.
3.
Bread
12*20.50
A
=246.00
Overriding the pre-programmed
PLU price
Either the pre-programmed price or a price entered from the keyboard may be used for PLU
registration. If both methods are possible, the
cash register uses the price entered from the
keyboard.
Example: The customer has been given a special price, different from the pre-programmed
This feature helps when you enter a large qu- one. PLU 3 has the pre-programmed price of
antity of items or need to enter quantities that 21.40, but the special price is 20.50.
contain decimals (1.5, 0.125; etc.). Multiplication by numbers with the decimal part is often
Step
Press
used by the weighed items (meat, vegetables,
1.
salads etc.) where the unit price is known (e. g.
for 1 lb or for 1 litre, etc.). The maximum mul2.
tiplicand is 9,999.
Individual PLU registration
Bread
1*20.50
A
=20.50
In some services, just a single item is often
sold, e.g. cigarettes. To simplify the sale of such
items, it is possible to program a single sale
PLU flag (see PLU programming). By entering
the PLU number and the v (PLU) key, the item
is registered, the sale is automatically finished
41
Euro-2100
© Elcom, s. r. o.
Registration mode
Fractional PLU registration
Double multiplication in PLU
registration
The function must be programmed by setting
the second system flag, digit no. 6 to 0.
The function must be programmed by setting
the second system flag, digit no. 6 to 1.
Example: The price is determined for packing
including five pieces of the article (e. g. a box of Example: The price is determined for the a squprocessed cheese) at the price of 15.60. The custo- are metre. Your customer buys 3 by 5 meters.
mer buys only three pieces. Thus, he is to pay
Step
Press
three fifths of the unit price of the whole box.
1.
3
Step
Press
2.
5
1.
3.
2
2.
3.
Butter
3/5*15.60
Linen
3*5*15.60
A
234.00
A
=9.40
Other means of registration
Registration using bar-codes
•
•
registration by a bar-code entered via the
keyboard
registration using a bar-code scanner
A bar-code scanner can be connected to the
cash register. Information is then registered
simply by scanning the bar-code on the article’s
packaging. If the bar-code scanner is to operate
correctly, it has to be properly configured and
the ECR has to have its relevant flags set to
proper values, more specifically the fifth system
flag (see PLU bar-code programming section
in the previous chapter).
Example: Customer buys three pieces of butter
that have a bar code on its packaging.
Step
In the case of bar-code scanner failure or if a
bar-code is damaged, it is possible to enter the
bar-code via the keyboard.
Example 1: Registration of beer with the bar-code 8 586001 760096.
Step
Press
1.
#
2.
3.
Butter
1*12.40
Press
1.
2.
using a bar-code scanner
Butter
3*34.90
A
=104.70
A
=12.40
Example 2: Registration of five beers with the
bar-code 8 586001 760098.
Step
Press
1.
2.
3.
4.
42
#!…!
#
#!…!
Euro-2100
Registration mode
Butter
5*12.40
A
=62.00
Weight entry by electronic scales
© Elcom, s. r. o.
To achieve the correct operation of the electronic scales, it is necessary to set the type of scales
by programming the fifth system flag of cash
register.
Ask your local dealer for more information on
the particular electronic scales type connectivity.
The Euro-2100 is able to read the weight of an
Registration using an external PC
article directly from connected electronic scales. Communication between the cash register
keyboard
and the scales is possible only in “R” and “T”
mode. The electronic scales are connected to The standard PC keyboard can be easily conSCAN./SCALE connector of the cash register. nected to the Euro-2100. Registration is then
similar to registration via the internal keyboPress the d button to communicate the weight ard.
with the Scales. You can change the weight of the article (add or take from the goods If one key is used for two characters, then the
on the scales) until the any key is pressed on character in a lower part is chosen by pressing
ECR keyboard. After the weight is read by the the actual key, the character in the upper part
cash register, enter the PLU number and press on the left side is chosen by pressing this key
the (PLU) button. If the weight on the along with the Shift key and the character in
scales is unstable, it is not possible to continue the upper part on the right side is chosen by
pressing this key along with the Alt key.
the sale.
Example: Registration of PLU no. 21 with we- Ask your local dealer for more information
about external PC keyboard connection.
ight 0.253 kg.
PC ON-LINE mode
Step
Press
1.
2.
reading of weight from scales
3.
Appels
0,253*31.20
Data are transmitted from a PC to the
cash register
A
=7.90
The cash register software allows the use of the
Euro-2100 as a fiscal printer. The cash register
replaces the POS printer and the PC fiscal module. This means that the cash register prints
the receipt based on your data from your PC
software.
This feature is useful where simple registration
is not sufficient due to the high quantity of
PLUs and where sales’ cadence is not high.
<
Figure 4.1
PC keyboard layout for
the Euro-2100 ECRs.
43
Euro-2100
© Elcom, s. r. o.
Setting up the PC ON-LINE mode:
The cash register is ready to communicate with
a PC (PC ON-LINE mode) in “R” or “T”
mode, when no sale is in a process of registration. The PC can transmit information on a
PLU sale, a PLU refund, a sale finishing signal,
or a PC-ON LINE mode finishing signal. The
text “PC” is displayed on the display.
PC
White wine
1 ks
86.20
Sales data transmitted from PC are added into
the financial data of departments, tax levels,
and sales data of PLU called PC ON-LINE.
The keyboard is inoperable in the PC ON-LINE mode, except the (Clear) key. By
using this key it is possible to exit the PC ON-LINE mode any time. The text “PC” will disappear from the display.
Registration mode
Data are transmitted from the cash
register to PC:
The cash register software allows use of the
Euro-2100 as on-line information source for
PC or payment terminal. This allows transmission of the sales data to a PC for processing or
transmitting data for payment terminal. It allows the preparation of an invoice or delivery
note by the PC according to information from
the cash register.
Setting up the PC ON -LINE:
If the cash register is in “R” or “T” mode, pressing the , (Cash) (Cheque) or (Credit) keys will transmit information about
the PLU sale, PLU refund, purchase finishing
signal and information about type and amount
of payment to the PC. The text “PC” will appear on the display during the communication
at the end of sale when the sale is finishing.
Switching the cash register off and on prepares
By switching the cash register off and on, the
the cash register for standard registration.
cash register is ready for standard registration.
Sales data transmitted from PC are added to
the financial data of the departments and tax The data transmission direction for the PC
levels. Sales values are recorded in the cash re- ON-LINE mode is set by the setting the fifth
gister under a special PLU called PC ON-LI- system flag, digit no. 5 to 1.
NE. PC ON -LINE sales values can be printed
Ask your local dealer for more information
and reset by using the full PLU report.
about PC ON-LINE mode.
It is impossible to manipulate programmed
and sales data of the special PLU called PC ON
-LINE in the EuroSoft software.
Clearing
In the following example, the price 12.30 was Void is used just to correct already sold items in
incorrectly registered instead of 12.90
the the non-finished sales.
• correction of the last entry (direct voidanStep
Press
ce)
1.
Example: The previous item was registered
2.
$ incorrectly and it is necessary to make a correction. If a mistake is made in an incorrect
3.
2 c
department, PLU, percentage, deduction or
other entry, void the incorrect entry by pressing the b (Void) key immediately after the inButter
(0002) [
correct entry.
1*12.90
=12.90
44
Euro-2100
Registration mode
Step
1.
2.
3.
Bread
1*27.00
Butter
1*31.20
VOID
Bread
1*27.00
Department 2
A
1*12.50
=12.50
VOID
Department 2
A
1*12.50
=12.50
Department 2
A
1*13.50
=13.50
(1)
VOID
-12.50
correction of the previous entries (indirect
voidance)
You can void any previous registrations (not
the last). Pressing the special keys, you can display any previous registration. Then press the
(Void) key. Special keys are: (jump
to the previous), (jump to next), (jump five items back) and (jump five
items forth).
Step
1.
2.
3.
Press
"
A
=27.00
27.00
voidance of receipt (subtotal voidance)
Example: Void the whole receipt. Subtotal voidance is used for total voidance of a sale. It
can be used only before pressing the (Total) key.
Step
1.
2.
3.
4.
5.
6.
Example: Void the first PLU in the sale (Gentian Cheese).
A
=27.00
A
=31.20
Bread
1
•
•
© Elcom, s. r. o.
Press
Press
!
Department 1
A
1*31.20
=31.20
Department 2
A
1*18.60
=18.60
Department 6
A
1*6.30
=6.30
SUBTOTAL
56.10
SUBTOTAL VOID -56.10
***************************
RECEIPT VOIDANCE
***************************
Percent surcharge and discount
The system permits programming of a per cent
that is usually used for a surcharge and
for a discount If you need to register a
different rate than the one that is pre-program-
med, enter the numeric value of the surcharge
or of the discount before pressing the relevant
key. The value of the new rate will be effective
only for one registration.
45
Euro-2100
© Elcom, s. r. o.
Registration mode
Percent surcharge
Entering the surcharge value from the keyboard is possible if the value is lower than the preExample 1: A five per cent surcharge for special -programmed limit (see seventh system flag).
services is added. In the following example the
(Surcharge) key was programmed for In the case of a linked PLU, the surcharge is
five percent.
applied to the first item only.
Percent discount
If all items within a transaction have the same
handling charge, the charge may be added at
one time for the whole transaction. When all Example: Pensioners are provided a 10 disitems have been registered on which the sur- count.
charge is applied, press the (Subtotal)
Step
Press
and then the (Surcharge) key.
1.
Step
Press
2.
1.
Department 2
A
2.
1*31.20
=31.20
DISCOUNT%Department 2
A
10%
1*31.20
=31.20
=-3.10
ADD ON%+
5.00%
=1.60
DISCOUNT%ADD ON%+
3.10
1.60
If the same discount is to be deducted from all
Example 2: Enter other than pre-programmed PLUs within the transaction, the discount for
rate (10 ).
the whole transaction may be entered in one
operation. When all items on which the discount is to be applied are registered, simply press
Step
Press
the (Subtotal) key, then the (Discount) key. Use of other than pre-program1.
med per cent discounts is the same as a percent
2.
surcharge.
Department 2
A
1*31.20
=31.20
ADD ON%+
10%
=3.10
Entering the discount value from the keyboard
is possible if the value is lower than the pre-programmed limit (see eighth system flag).
In the case of a linked PLU, the discount is applied to the first item only.
Reference number and customer number
Certain transactions require that a reference
number is printed on the receipt. If a reference
number is required, use the (Drawer) key.
By pressing the (Drawer) key when there is no open sale, the cash register drawer
46
Step
1.
Press
#
DOCUMENT NUMBER
#312085
Euro-2100
Registration mode
© Elcom, s. r. o.
opens and the printer prints a receipt with the The text DOCUMENT NUMBER can be chan“Drawer open” notification.
ged in the programming mode. See Function
texts programming section.
Received on account
The (RA) key is used to record non-fiscal payments (that are received on account).
As an example, daily initial cash can be entered
into the cash register drawer. The register enables printing a document that confirms the receive on account transaction. The RA transactions are reported in the cash register financial
report. According to your needs, the document
can contain the name of the person that performed the RA and the reason for the RA. The
name and reason of an RA can contain up to
24 characters. There is space for a signature on
the document.
Step
RA
WHO:
Brown
REASON:
Initial cash
SIGNATURE:
CASH
500.00
GBP
500.00
RA
NAME
Press
1.
2.
3.
enter name
4.
5.
enter reason
6.
REASON
Initial cash
Entry of person name and reason is not mandatory. If you do not need to enter these data,
finish RA operation by double pressing the (Subtotal) key.
Paid out (cash or cheque)
Cash or cheques paid out from the register
drawer that are not connected with a sale are
recorded using the (PO) key. This
function is used, for example, by taking away
revenue, when cashiers are changing, or when
it is suitable to lower the amount of money in
the drawer. According to your needs, the document can contain the name of a person and the
reason for the PO operation. The name and
reason of the PO can contain up to 24 characters. There is space for a signature on the
document.
Step
1.
2.
Press
3.
enter name
4.
5.
enter reason
6.
47
Euro-2100
© Elcom, s. r. o.
Registration mode
Entry of a name and a reason is not mandatory.
If you do not need to enter these data, finish
the PO operation by double pressing the (Subtotal) key.
PO
WHO:
BROWN
REASON:
Cashier change
SIGNATURE:
If the PO operation involves cheques, press the
(Cheque) key instead of the (Cash) key.
CASH
2000.00
GBP
2000.00
PO
Refunds
The (Refund) key records refund entries during a PLU sale or as an independent
operation. The function is used, for example,
in handling complaints.
REFUND
Department 13
A
1*-31.20
=-31.20
Example 1: It is necessary to refund goods re- Example 2: Returning of goods registered ungistered under department no. 2 with program- der department no. 13 with entering of price
med price 25.20.
via keyboard.
Step
1.
2.
Step
Press
1.
2.
REFUND
Department 2
A
1*-25.20
=-25.20
resp.
Press
( )
REFUND
Department 13
A
3*-31.20
=-93.60
Department 2
1
-25.20
Example 3: Returning of three pieces of the
same item registered under department no. 13
After pressing the (Refund) key, the with entering of price via keyboard.
“REFUND” label appears on the display. After
Step
Press
pressing the (DPT) key the count of refunded
1.
products and the name of DPT is displayed
in the upper right side of the display; also the
resp.
( )
value of refunded products is displayed in the
2.
bottom line.
Step
1.
2.
resp.
48
Press
( )
REFUND
Butter
1*-31.20
A
=-31.20
Euro-2100
Registration mode
Example 4: Returning of items registered under the PLU no. 3.
Step
After pressing the (Refund) key, the
“REFUND” label appears on the display. By
pressing the (PLU) key the count and the
name of refunded product is displayed in the
upper right side of the display and the value of
refunded products is displayed in the bottom
line.
2.
1.
resp.
3.
© Elcom, s. r. o.
Press
( )
REFUND
Chocolate
5*-31.20
A
=-156.00
Example 5: Returning of five pieces of the same
item registered under PLU no. 13. with entering of price via keyboard.
board. Payment was tendered in cheques (the
value of refund flag is 1).
Step
1.
2.
resp.
Press
( )
The manner of handling for cheque and credit
refund depends on the setting of the refund flag.
Setting the refund flag:
1) Switch the cash register into the “X” mode:
.
A
2) Press the numbers #on the nu=-156.00
meric keyboard.
3) Press the (Multiply) key. The information about the change and the flag value
Example 6: Returning of goods registered unare displayed: 0 – subtracting from cash,
der PLU no. 13. with entering of price via key1 – subtracting by sale finish type (default).
REFUND
Chocolate
5*-31.20
Registration using the euro currency
The Euro-2100 cash register is able to register
sales in the Euro currency. According to the
stage, it is possible to register in euro, particular national currency (1st and 2nd stage), or any
other foreign currency (3rd stage).
rency. If the (Price) key is pressed, the
amount of sale is converted to euro. Pressing
the (Price) key again, the subtotal amount
currency toggles from national to euro. After
choosing the required currency, press the (Total) key.
The registration in euro is divided into four
stages:
All financial data are stored in the national currency. Only the cash amount, the cash in the
Stage without euro
drawer, and RA and PO amounts are stored in
both currencies. The RA or PO operation in
the national currency can be done according to
The cash register works without euro.
the procedure described in previous chapter. As
First euro currency stage
to an RA or PO operation in euro, it is similar
to any common operation, but first it is necesIn the first stage, the master currency is the na- sary to press the (Price) button.
tional one, the secondary is euro. The customer can pay either in national currency or in
Step
Press
euro.
1.
Procedure:
2.
If the (Subtotal) key is pressed, the amount of the sale on the display is in national cur-
3.
49
Euro-2100
© Elcom, s. r. o.
Step
Registration mode
Step
Press
Press
4.
enter name
1.
5.
2.
6.
enter reason
3.
7.
4.
enter name
RA
WHO:
Brown
5.
6.
enter reason
7.
REASON:
PO
WHO:
Initial cash
SIGNATURE:
CASH
Brown
REASON:
Cashier change
SIGNATURE:
500.00
Example: RA of 500.00 euro in the first stage
of the Euro currency.
CASH
2000.00
Example: RA of 500.00 euro in the first stage The transition into the second stage is described
of the Euro currency.
in the program manual of this user manual.
Second euro currency stage
Third stage of the Euro
In the second stage, the master currency is euro,
the secondary currency is national one.
The customer can pay either in euro or in national currency.
In the 3rd stage, the master currency is euro,
the secondary currency is any foreign one. The
customer can pay either in euro or in any foreign currency.
Procedure:
Procedure:
If the (Subtotal) key is pressed, the amount of the sale on the display is in master currency – euro. If the (Price) key is pressed,
the amount of the sale is converted to the national currency. Pressing the (Price) key
again, the subtotal amount is converted and
displayed in the national currency or in euro.
After choosing the required currency, press the
(Total) key.
All financial data are stored in euro. Only the
cash amount, the cash in the drawer, and RA
and PO amounts are stored in both currencies.
The RA or PO operation in the euro can be
done according to the procedure described in
the previous chapter. As to RA or PO operation in the national currency, it is similar to any
common operation, but first it is necessary to
press the (Price) key.
If the (Subtotal) key is pressed, the amount of the sale on the display is in the master currency – euro. If the (Price) key is
pressed, the amount of the sale is converted to
the secondary currency. Pressing the (Price) key again, the subtotal amount is converted and displayed in the national currency or
in euro. After choosing the required currency,
press the (Total) key.
All financial data are stored in euro currency.
Only the cash amount, the cash in drawer, and
RA and PO amounts are stored in both currencies. The RA or PO operation in the euro currency can be done according to the procedure
described in the previous chapter. As to an RA
or PO operation in the secondary currency, it
is similar to any normal operation, but first it is
necessary to press the (Price) key.
Note: The transition into the 3rd stage is descriExample: Pay out cash of 2,000 DKK in the bed in the program manual of this user manual.
2nd stage of euro currency.
50
Euro 2100
Reports
© Elcom, s. r. o.
Reports
How to print out reports
There are two modes for printing reports: “X” ading may be made in any numbers. It does
mode and “Z” mode.
not affect the cash register memory.
Use the reading functionality of “X” mode if
it is necessary to obtain sales information since
the last resetting. It is used to generate reports
during the day, between two shifts, etc. The re-
Use the resetting functionality of “Z” mode
when you need to print reports and to clear the
register’s memory. “Z” report is usually carried
out once a day after finalising the daily report.
Generated reports
Report
“X” mode
“Z” mode
Department
•
PLU
•
Cashier
•
Financial
•
Total (daily)
•
•
Periodical
•
•
•
In the “Z” mode the department report, the
cashiers report and the financial report are carried out within the total “Z” report.
Report contents
Department report
PLU report
When printing a full department report, only Three different types of PLU reports can be
departments with non-zero sales are printed.
printed: the individual PLU report, report of
PLU range, and the full PLU report. Each of
Report contains:
these types can contain the PLU number (de1) Name of the department
pends on the report mode) or calling and stock
2) Number of items sold in the department
status according to the setting of second PLU
3) Total value of the items sold in depart- flag.
ment
4) Total value of sales including all depart- When printing a PLU report, only PLUs with
ments
non-zero sales are printed.
In the “Z” mode it is possible to print the de- A PLU report contains:
partment report only within the total “Z” report. See chapter on total daily “Z” report.
1) Number of the PLU (selective according to
the mode of report function calling).
51
Euro 2100
© Elcom, s. r. o.
Reports
2)
3)
4)
5)
The name of the PLU.
20) Cash value in the cash drawer.
Number of the PLU sold.
21) Cash value in the cash drawer in foreign
Financial value of the PLU sold.
currency (Euro)
PLU stock status (according to the setting 22) Cheque value in the cash drawer.
of the second PLU flag).
None of the above categories with zero values
The full PLU report prints by PLU the total fi- will be printed. The financial report can be prinnancial value of sales from the last reset. PLUs ted only by means of the total “Z” report in the
that were not activated are not printed.
“Z” mode. See chapter on total daily “Z” report.
Stock level report
Cashier report
Euro-2100 allows to print more types of stock
level reports: stock level report of one PLU, When printing the full cashiers report, only
stock level report of the range of PLUs and non-zero values will be printed.
total stock level report.
The cashier report prints:
Only the data about PLU with store level
listing allowed, with value different from zero 1) The cashier’s name.
and not forbidden PLU will be printed in the 2) The number of sales transactions (number
stock level report.
of customers) per cashier.
Report contains:
1. PLU number
2. PLU name
3. Current PLU stock level
3) The total sales value for each cashier.
In the “Z” mode the cashier report can be printed only by means of the total “Z” report. See
chapter on total daily “Z” report.
Financial report
The financial report contains:
1) Value of cumulative totals (grand totals)
GT1, GT2 and GT3.
2) Taxable amounts and taxes of all tax levels.
3) Overall sales value.
4) Overall sales value without tax.
5) Value of total tax.
6) Number and value of voids.
7) Number and value of refunds.
8) Number and value of discounts.
9) Number and value of add-ons.
10) Number and value received by cash payment.
11) Number and value received by cash in foreign currency (Euro)
12) Number and value received by check payment.
13) Number and value received by credit card
payment.
14) Number and value received on accounts by
cash.
15) Number and value received on accounts by
cash in foreign currency (Euro)
16) Number and value received on account by
cheques.
17) Number and value paid out by cash.
18) Number and value paid out by cash in foreign currency (Euro)
19) Number and value paid out by cheques
52
Total daily “X” report
Total “X” report contains:
• consecutive number of the total “Z” reports
that have already been executed
• department report
• cashier report
• financial report
Periodical “X” report
The periodical “X” report gathers financial
data from the total “Z” report in the course of
longer time period (i.e. a week, a month, etc.).
This report prints all financial data accumulated since the last total “Z” report.
Total daily “Z” report
The total “Z” report contains:
•
•
•
•
consecutive number of the total “Z” report
being executed on the machine
department report
cashier report
financial report
After printing the memory contents of the total
“Z” report, the data are added to the memory
Euro 2100
Reports
© Elcom, s. r. o.
registers of the periodical report and they are The periodical “Z” report gets the data from
then reset.
the total “Z” report throughout a longer time
period. It is usually printed weekly, monthly, or
Periodical “Z” report
quarterly or as needed. After printing the memory contents of the periodic “Z” report, the
memory is cleared.
How to print “X” reports
Switch the cash register into the “X” mode:
.Press any of the key combinations
shown in table  to print proper reports.
The “X” report can be printed as many times as
desired without influencing data in ECR memory.
15-12-2005
11:07:39
X
“X” report
Key operation
Cashier
Financial
Departments
Using this type of report you can get information about sales during the day. Values can be
used to check the cash balance in cash drawer,
the daily turnover in the store, and the sales
when shifts or cashiers are being changed, etc.
Pressing the PLU (Refund) key before
pressing thea (PLU) stlačiť tlačidlo (Refund), čím je na uzávierke pred predajnými údajmi vytlačené aj číslo PLU.
department button ( – , )
( ) Individual PLUPLU,number (1 −
(
… $) ( ) 2100)
Full PLU
PLU range
PLU stock level
Total (daily)
Periodical
starting PLU number finishing PLU number ( ) Samples of “X” reports
The cashier’s report provides an overview of
the activity of individual cashiers. The report
provides a summary of the number of customers served by a particular cashier and the total
receipts. This data permits rewarding the staff
based on total receipts or productivity and intensity of work.
***************** X *****************
***********************************
CASHIER REPORT
***********************************
Smith
SALE
27Q
1134.64
Hopkins
SALE
2Q
126,60
The department report provides a picture of
the sales frequency of individual articles within
a group of products. The cash register provides
data concerning the number of items sold and
turnover in the department, as well as the share
of department sales as a whole.
***************** X ****************
***********************************
* DPT REPORT *
**********************************
Groceries
3.000Q
93.60
Dairy
6.000Q
111.60
Stationery
4.000Q
124.80
DPT TOTAL:
330.00
53
© Elcom, s. r. o.
Euro 2100
***************** X *****************
***********************************
PLU REPORT
************************************
Bread
10.000Q
118.20
Butter
10.000Q
259.00
Fruit tea
7.000Q
35.40
Cigarettes
1.000Q
70.00
PLU TOTAL:
482.60
PLU report provides the most exact preview of
each item sales. Example of report on the right side is without listing the stock level and
number of PLU. Example of report on the left
side contains maximal available data of PLU
report. Because this report provides most extended data, we recommend to use a PC with
attached SW for programming of PLU and
stock level control and for evaluation and print
of sales preview.
The total “X” report provides detailed sales information during the day. It contains sales information within departments, total receipts,
the cashier’s share of receipts, taxable revenue
corresponding to the tax rate, the number of
corrections and refunds, and the cash or check
amounts in the drawer. Receipts are separated
from non-business transactions, i. e. received
on accounts and payouts.
**************** X ****************
***********************************
DAILY REPORT
***********************************
* Z1 #:
0001 *
***********************************
* DPT REPORT *
54
Reports
***************** X *****************
***********************************
TOTAL REPORT
***********************************
*Zn#:
0003*
***********************************
DPT REPORT
***********************************
Groceries
13.000Q
330.00
Dairy
6.000Q
111.60
Stationery
4.000Q
124.80
DPT TOTAL:
566.40
***********************************
CASHIER REPORT
***********************************
Hopkins
SALE
7Q
566.40
***********************************
FINANCIAL REPORT
***********************************
GT1
2789.97
GT2
2671.67
GT3
-118.30
TAXABLE VAT5%
566.40
NET VAT5%
539.42
VAT5%
26.98
TOTAL SALE
7Q
566.40
NET TOTAL
539.42
VAT TOTAL
26.98
REFUND
2Q
-37.20
VOID
2Q
58.20
CASH
5Q
-502.00
CHECK
1Q
68.40
CREDIT
1Q
1000.00
RA-CASH
1Q
500.00
PO-CASH
1Q
4000.00
RA-CHECK
1Q
3000.00
CASH
DRAWER
-4002.00
CHECK
DRAWER
3068.40
CREDIT
DRAWER
1000.00
Euro 2100
Reports
© Elcom, s. r. o.
The “X” report is often used to check revenu- The number of all total “Z” reports performed
es and cash received when the operator changes on the cash register is marked as Z1.
during the working day. Management can secure sales information at any time during a day.
How to print “Z” reports
Switch the cash register into the “Z” mode:
. Press the required keys according to the
table. If a large number of PLUs is used, it is
recommended that a computer be used to print
the PLU report.
During PLU report cash register allows by pressing /shift/ /rf/ (REFUND) before pressing the
key /PLU/ to print number of PLU in a front
of sales data.
To execute a PLU report without printing,
press $$$$$. PLU sales amounts will be deleted without printing.
12:19:23
Z MODE
“Z” report
Key operation
Full PLU
( ) Individual PLU, PLU number (12100)
… $ ( ) PLU range
starting PLU number finishing PLU number ( ) Total (daily)
Periodical
Samples of “Z” reports
The PLU report provides the most precise overview of the sales of each product. The
sample report on the left side is without stock
printouts and without PLU numbers (without
pressing (Refund) before pressing (PLU). The
sample report on the right contains all information. As it provides the most detailed information, it is recommended that a computer be
used for PLU programming, for running store records, for evaluation and the for printing
sales reports. The EuroSoft software supplied
with the cash register is sufficient for basic operations.
***************** Z *****************
***********************************
PLU REPORT
************************************
Bread
13.000Q
199.20
Butter
14.000Q
383.80
Fruit tea
10.000Q
66.00
Cigarettes
1.000Q
70.00
PLU TOTAL:
719.00
Number of all Total “Z” reports performed on
the cash register is designated as Z1 and the
number of all Periodical “Z” reports performed
on the cash register is Z2.
55
Euro 2100
© Elcom, s. r. o.
***************** Z ******************
*************************************
TOTAL REPORT
****************************************
* Z1 #:
0004 *
***************************************
* DPT REPORT *
****************************************
Groceries
13.000Q 330.00
Dairy
6.000Q 11.60
Stationery
4.000Q 124.80
DPT TOTAL
566.40
***********************************
CASHIER REPORT
***********************************
Hopkins
SALE
7Q
566.40
***********************************
FINANCIAL REPORT
***********************************
GT1
2789.97
GT2
2671.67
GT3
-118.30
TAXABLE VAT5%
NET VAT%
VAT5% 26.98
TOTAL SALE
7Q
566.40
NET TOTAL
VAT TOTAL
REFUND
2Q
-37.20
VOID
2Q
58.20
CASH
5Q
-502.00
CHECK
1Q
68.40
CREDIT
1Q
1000.00
RA-CASH
1Q
500.00
PO-CASH
1Q
4000.00
RA-CHECK
1Q
3000.00
CASH
DRAWER
-4002.00
CHECK DRAWER
3068.40
CREDIT DRAWER
1000.00
56
556.40
539.42
539.42
26.98
Reports
***************** Z ******************
***********************************
MONTHLY REPORT
***********************************
* Z2 #:
0002 *
* Z1 #:
0004 *
***********************************
* DPT REPORT *
***********************************
Groceries
47.000Q
1250.21
Dairy
34.000Q
690.86
Liquors
5.000Q
135.00
Stationery
12.000Q
374.40
Hardware
3.000Q
93.60
DPT TOTAL:
2544.07
***********************************
CASHIER REPORT
***********************************
Smith
SALE
27Q
1134.64
Hopkins
SALE
11Q
1409.43
***********************************
FINANCIAL REPORT
***********************************
GT1
2789.97
GT2
2671.67
GT3
-118.30
TAXABLE VAT5%
2369.47
NET VAT5%
2256.63
VAT5%
112.84
TAXABLE VAT0%
174.60
NET VATO
275.69
VAT0%
0.00
TOTAL SALE
38Q
2544.07
NET TOTAL
2431.23
VAT TOTAL
112.84
ADD ON%+
2Q
6.24
DISCONT%1Q
-0.10
REFUND
6Q
-118.20
VOID
5Q
128.90
SUBTOTAL VOID
1Q
56.10
CASH
35Q
1448.67
CHECK
1Q68.40
CREDIT
2Q
1027.00
RA-CASH
2Q
1000.00
PO-CASH
3Q
6200.00
RA-CHECK
1Q
3000.00
CASH
DRAWER
-3751.33
CHECK
DRAWER
3068.40
CREDIT DRAWER
1027.00
Euro2A software
Euro–2100
© Elcom, s. r. o.
Euro2A software
The Euro-2100 ECR is also deliver with the Euro2A software that makes programming, reporting and set-up for the Euro-2100 user easier.
The software allows simple and easy editing and transfer of all possible ECR data (ranging from
setting of the system flags, through logos up to programming PLUs and departments), enables
back-up of the ECR data, processes sales data and many more useful functions.
The most up-to-date version of Euro2A software is available for you to download from company‘s web page, http://www.elcom.sk.
57
© Elcom, s. r. o.
Euro-2100
Optional ECR accessories
Optional ECR accessories
Cash drawer
The Euro-2100 ECR allows connection of majority of cash drawers that are based on solenoid
opening mechanism (12-15 V; 1.2 A/24 V; 1.5 A). The ECR is equipped with cash drawer interface by default.
The cash drawer is connected to the ECR via a cable that enables its automatic opening. The cable and the connector is easily detachable. Small establishments will surely welcome the possibility
to place the cash drawer anyplace they wish and open it automatically using the ECR. The cash
drawer is opened automatically only if the ECR is powered
from mains; it will not work when ECR is powered from
the internal battery.
It is also possible to connect a FLIP TOP cash drawer (24
V) to the Euro-2100.
Ask your authorised Euro-2100 dealer on delivery and installation of cash drawers.
Electronic scales
The Euro-2100 ECR allows connection of multiple types of
electronic scales. The scales are usually equipped with the serial interface that enables them to co-operate seamlessly with the Euro2100 cash registers. You can use electronic scales also separately,
without connection to the Euro-2100. The electronic scales that
are delivered with Euro-2100 ECRs are certified and equipped
with a communication cable upon request.
Ask your authorised Euro-2100 dealer on delivery and installation
of electronic scales.
Bar-code scanners
Interface for connecting bar-code scanners is a default feature of Euro-2100 ECRs. In case you
wish to use bar-code scanners, this chapter will help you select the bar-code scanner suitable for
your establishment. In any case, we recommend consulting this decision with your authorised
Euro-2100 dealer.
The bar-code scanner is connected to the ECR via the standard
RS-232 interface. The same interface must be available on the
bar-code scanner. The ECR supplies +5 V DC voltage to power
the bar-code scannner. Both the ECR and the scanner must be
programmed appropriately in order to work together properly.
Metrologic bar-code scanners are the recommended option for
Euro-2100 ECRs. Ask your authorised Euro-2100 dealer on
further information on bar-code scanners.
58
Optional ECR accessories
Euro-2100
© Elcom, s. r. o.
Metrologic MS-5145 ECLIPSE
Scanning after pressing a trigger, hand scanner without
stand, power supply 5 V, 72 chars/s, scanning range 140
mm, RS-232 interface (model 5145 R).
Metrologic MS-6720
Combination of hand and stand scanner, great ergonomy, concentrated omnidirectional scanning mode, flexible handling, adjustable stand, easy programming, low cost, power supply 5 V,
1,000 rows/s, maximum scanning range 205 mm.
Metrologic Orbit MS-7120
Multidirectional, quick, presentable laser bar-code scanner. It‘s equipped with holographic scanning technology for barcodes. HoloPrism VLD technology allows focusing of rays in very large
scanning field depth (0-215 mm). The design is directed at use in limited space. Orbit is ideal
for small stores. Its unique shape allows this scanner to be also used as a hand scanner for large
packages. The scanning head can be vertically tilted up to 30 degrees. Power supply is 5 V, 1,200
rows/s, RS-232 interface available.
Metrologic MS-7625 - Horizon
Hardy runner for professionals, this compact scanner offers gense 20-row omnidirectional scanning grid, that offers quick and highly effective scanning of bar-codes. The bar-code is scanned
in one go over the scanning head. The price/performance ratio places this scanner as ideal candidate for convenience stores, hyper- and supermarkets and large shopping centres. Power supply
is 24 V, 2,000 rows/s, maximum scanning range is 179 mm.
Metrologic MS-9520 Voyager
Handheld laser scanner, hand and stand use. Row scanning mode, easy
programming, scanning speed 72 rows/s, scanning range 205 mm, power
supply 5 V, RS-232 interface (model 9520 R).
Ask your authorised Euro-2100 dealer on further information for scanner
types not mentioned here.
Electronic payment terminals
The Euro-2100 ECR allows connection of electronic payment terminal to allow payment by credit/debit cards. You
can ask any banking institution to supply and connect the
payment terminal.
External keyboard
There are multiple types of external keyboards available for the Euro-2100 ECR.
The first type of external keyboard is the EK-3000 keyboards that ideally complement the system
in retail, since their use is easy to learn and quick. The keys are fully programmable and of course
it‘s possible to easily replace the key labels. Every key on a EK-3000 keyboard can sustain up to
50 million strokes which is seven times more than a PC keyboard can sustain. The logging in of
cashiers is made easy thanks to the RF reader, which is an optional accessory of the EK-3000.
59
© Elcom, s. r. o.
Euro-2100
Optional ECR accessories
Another advantage over a PC keyboard is the programmable key layout, along with pleasing design. The keyboard covers are manufactured in attractive green or
blue, in grey or in imitation wood. The EK-3000 can
also be connected to a PC or any electronic device that
is equipped with PS/2 port. The Elcom keyboard allow
our customers to express their uniqueness and identity.
The second option is the standard PS/2 PC keyboard.
UV LED banknote checker
The Euro-2100 ECR can optionally be equipped with UV LED banknote checker. Since the ratio of forged banknotes is not negligible, this accessory will help you uncover false banknotes.
Now you can use your Euro-2100 to check banknotes and save on buying separate equipment.
Optional internal battery
The design of Euro-2100 makes it easy to use the ECR as portable and take it out-doors. It‘s easily portable and with help of internal battery it can be used as back-up ECR in case of a power
black-out. Minimum battery life is eight hours.
LAN connection options
The possibility to connect Euro-2100 ECR into an Ethernet network is offered by the RS-232/
Etherner converter.
What is to be gained from this? You can save lot of finances, since this will enable you to create
single ECR network that can be composed from various types of Elcom cash registers.
New features of Elcom ECRs
The GSM communcation widens the possibilites for ECR/PC data interchange. Detailed and
quickly obtained data are crucial for proper management in retail. This modern technology will
greatly facilitate connection with any of Euro-2100 ECRs.
60
Euro-2100
Helpful advice
© Elcom, s. r. o.
Helpful advice
Information and error messages
If it is necessary to inform the operator on the an error state, the error messages shown in tacurrent status of the ECR, or the ECR enters ble 8.1 are displayed.
Message
Meaning
No external power supply is connected. The power supply is
internal accumulator. The percentage value indicates the stage
100%
of internal accumulator charge.
ADD ON - DISCOUNT LIMIT Add on or discount amount limit over. Check the system
flags.
OVER
ADD ON - DISCOUNT
Add on or discount to negative amount disabled.
TO NEGATIVE VALUE
ADD ON - DISCOUNT
Add on or discount to returnable packs disabled.
TO RETURNABLE PACKS
Information about amount that has to be paid for sale termiAMOUNT DUE
nation.
Bar code is assigned to another PLU.
BAR CODE DUPLICATE
Credit card not accepted during EFT terminal payment.
CARD NOT ACCEPTED
ECR sorts programmed bar codes.
CODE SORTING
Communication error between ECR and PC or EFT termiCOMMUNICATION ERROR
nal.
ECR is ready to continue on sale.
CONTINUE ON SALE
CREDIT CARD PAYMENT LIMIT
Credit card payment limit is over.
OVER
Incorrect date entry.
DATE ERROR
Incorrect date entry.
DATE REVERSE ORDER
DECIMAL PLACES
Second system flag disables sale for more decimal place.
LIMIT OVER
Sale through this DPT is forbidden.
DPT INACTIVE
The printing of duplicate of last receipt.
DUPLICATE PRINT
The communication between ECR and PC running.
ECR -- PC
No sale from daily (total) report execution.
ECR AFTER REPORT
It’s mandatory to specify a customer. Enter 8-digit customer
ENTER DOCUMENT NUMBER
number.
Unblocking programming mode can be done only by entry
ENTER SERVICE CODE
of service code.
ENTER THE AMOUNT
Enforced entry of customer cash before sale termination.
OF CUSTOMER CASH
Unexpected entry. Incorrect sequence of keys pressed.
ENTRY ERROR
Maximum count of PLU in a sale has been reached (50), or
FINISH PURCHASE
maximum count of lines in one receipt has been reached.
Incorrect flag entry.
FLAG ERROR
FORBIDDEN ENTRY
Operation of bottles not can be performed.
OF RETURNABLE PACKS
Grandtotals reached the maximum amount. Execute daily (toGT LIMIT OVER
tal) and periodical report. Call your service technician.
EXECUTE REPORTS
Performed operation caused negative Grandtotal.
GT NEGATIVE VALUE
Information on the thermal head overheat. Wait a moment
HEAD OVERHEAT
until normal condition returns.
61
Euro-2100
© Elcom, s. r. o.
Message
HEAD UP POSITION
ILLEGAL EURO PHASE
ILLEGAL INVASION TO EPROM
ILLEGAL PAYMENT
ILLEGAL TAX RECEIPT
INACTIVE TAX
INCORRECT MODE
INVALID RECEIPT
ITEM NOT SOLD
MAX. STOCK
LIMIT OVER
MULTIPLICATION
LIMIT OVER
NOT PROCESSED BARCODE
OPEN PRICE INACTIVE
OPERATION CAUSED
NEGATIVE STOCK
PAPER MISSING
PARAMETER ERROR
PASSWORD
PASSWORD DUPLICATE
PAYMENT NOT ACCEPTED
PERFORM DAILY REPORT
PERFORM MONTHLY REPORT
PLU INACTIVE
PRESS KEY SUBTOTAL
PRICE HALO LIMIT OVER
PRICE MISSING
Prn
PROCESSING ERROR
PROGRAMMED PRICE
INACTIVE
RECHARGE BATTERY
SALE
SALE AMOUNT
LIMIT OVER
SCALES DISCONNECTED
SPLIT PRICING
DENIED
STANDBY
TAX LEVEL INACTIVE
TAX LEVEL
LIMIT OVER
TEAR OFF RECEIPT
AND PRESS SUBTOTAL KEY
UNAUTHORIZED ACCESS
UNKNOWN CODE
UNSUCCESSFUL CONTROL
WAIT PLEASE
VOID DISABLED
IN THIS PHASE
62
Helpful advice
Meaning
The thermal head is in an up position. Move it down to enable printing.
Access is not possible to this Euro phase.
Call for service!
This way of payment is not possible.
Receipt data has not been counted to ECR financial data. Illegal receipt.
Tax level cannot be assigned to DPT or PLU.
Incorrect mode. Finish operation before mode switching.
Receipt data is not counted to ECR financial data.
PLU not sold.
Stock amount reached max. 999 999,999.
Multiplication reached max. amount 10 000.
Bar code not processed during sale.
DPT (PLU) flag prevents entry of price from keyboard.
PLU flag prevents entry to negative stock.
Paper is missing in the printer.
Incorrect setting of ECR parameters.
It is necessary to cashier login.
Password is assigned to another cashier already.
Payment not accepted during EFT terminal payment.
Perform daily (total) report.
Perform periodical report.
PLU flag disables the sale of this PLU.
Press subtotal.
HALO limit over. Check the flags of DPT or PLU.
Programmed price is zero.
Receipt printing off. The printing can be switched on by
pressing f g button.
Error occurs during payment through EFT terminal.
DPT or PLU flag setting prevents use of programmed price.
It is necessary to connect external adaptor.
Normal sale mode. Data on receipt in R mode is counted to
GT.
Sale amount reached maximum. Terminate the sale.
Electronic scales are disconnected, or no data has been read.
PLU flag disables split pricing.
Standby mode. Exit the “standby” mode by pressing the A
(MODE) button.
DPT or PLU is assigned to inactive tax level.
Particular tax level amount over limit from the last daily report. Perform daily (total) report.
Get ready for electronic journal printing.
Cashier has no authorization to enter into this mode.
Bar code is assigned to no PLU.
Entered customer number is not saved in database of the customers (in the name of descriptive PLUs).
ECR executes operation that takes a longer time.
Void disabled in this stage of sale.
Euro-2100
Helpful advice
© Elcom, s. r. o.
What to do in case of power failure?
Power failure
This part is important only for registers that
operate without the built-in accumulator.
purchase; if one of the items has not been
added to the total sum of the purchase but
it was sold to the customer it is necessary to
register it additionally.
If you have used the register and a power failure
occurs, it is necessary:
Failures of register as a result of
interference in power network
•
•
•
to switch the register off
after electric power recovery switch on the
register
if the register displays the text Continue
on Sale it is necessary to complete the
purchase and compare the resulting sum
with the total of registered items within the
Accidental failures of electronic equipment are
frequently caused by the power network or by
electromagnetic interference. In case of intensive interference in your working area, or in case
of over or under voltage, installation of protective devices can help significantly. Ask your authorised dealer or service technician for help.
What to do in case of “Low BAT., finish sale ” signal
Displaying of the Low BAT., finish Long-term usage of the register when Low
sale warns the operator about discharging BAT., finish sale is signalled can rethe built-in accumulator.
sult in decreasing the accumulator lifetime or
in damaging the register. If the internal accuThe stage of internal accumulator charge de- mulator is very discharged and you want to
fines the percentage value in the upper left charge it by the external adaptor, first of all be
corner of the operators display. This percent- sure that ECR is turned off, then connect the
age value informs also that power supply of the external adaptor for at least 15 minutes (ECR is
ECR is internal accumulator (the external en- off ). The internal accumulator is charging even
ergizer is not connected). In case the charge is the ECR is turned off.
low (higher percentage value) the ECR displays
the text Low BAT., finish sale for a Care of internal battery:
short time and peeps alerting tone (e. g. by receipt printing when current input is higher). If • a complete battery charge takes 4-5 hours.
the discharge is higher (percentage value is low) • we suggest to charge a battery to 100  and
the text Low BAT., finish sale is disuse it till cash register starts to signalize the
played all the time and the ECR peeps alerting
battery charge requirement. Repeat this
and interrupted tone. After this warning the
process three times at least (it elongates an
cash register can print about hundred receipts.
endurance of the battery).
• we suggest to change the battery in case of
the battery decrease, e. g. shorter work cy10% Low BAT., finish sale
cle of the ECR after a battery charge.
• provide a battery charging only with a connected network.
It is necessary:
•
•
•
to register the purchase
to connect the register to the external
adapter
if it is not possible to connect the register to
the adapter, you should turn it off and start
to use it only after connecting the adapter
or battery box
63
Euro-2100
© Elcom, s. r. o.
Helpful advice
Self tests
Self tests of the Euro-2100 cash register permit the checking of its functionality simply
and quickly. Self testing permits the automatic checking of the functionality of electronic
circuits, display segments, keyboard buttons,
communication ports and the printer.
Self-test of the electronics and
display
FM enable/disable information and the complete character set in standard size with related
hexadecimal codes.
Procedure for running the self-test of the printer:
1) Switch ECR into the “P” mode: .
2) Press on the keyboard.
3) Press the (Multiply) button.
By executing this test, choice characters are
gradually lightened on and off in the both displays. Full characters will gradually displayed
on the cashier display. Then, the numbers from
0 to 9 are gradually displayed in the first row of
segments and the letters from A to J in the second row of segments.
The printer test end is announced by a beep.
You can continue in testing of other parts of
register.
1) Switch ECR into the “P” mode: .
2) Press on the keyboard.
3) Press the (Multiply) button.
Procedure for running self-test of keyboard:
Self-test of keyboard
The self-test of the keyboard displays the position, hexadecimal code and name after pressProcedure for running the self-test of the elec- ing a key. The test checks functionality of the
tronics and display:
register keys.
Switch ECR into the “P” mode: .
Press on the keyboard.
Press the (Multiply) button.
Press the individual buttons one after another and check the values on the display.
5) To finish the test press the (Total)
button.
1)
2)
Display test end is announced by a beep. You 3)
can continue testing other parts of register.
4)
Self-test of the printer
The self-test of the printer prints the identification data of the Euro-2100 on the receipt and If the key is functional, its position, code and
journal. It prints the program version number, name will appear on the display. Press the
cash register configuration (number of depart- (Total) button to finish the keyboard
ments, number of PLU), serial interface and test.
Service codes of the ECR
Codes accessible in the X-mode (press
to access it):
•
#
Switching of the time printing on the receipt.
•
#
Switching the check and credit payment
type when negative receipt total amount, e.
64
g. refund (cash, check or credit refund to
customer):
0 – subtracting from cash.
1 – subtracting by sale finish type (default).
Euro-2100
Notes:
© Elcom, s. r. o.
© Elcom, s. r. o.
Notes:
Euro-2100
Euro-2100
Notes:
© Elcom, s. r. o.
© Elcom, s. r. o.
Notes:
Euro-2100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement