Untitled

Untitled
www.tuv.com
Page 2 of 64
Report No.: 28207876 001
Copy of marking plate and summary of test results (information/comments):
Design of rating label of other models is identical to the above except for type designation, degree of
protection, sign of light source and flow rate. On the market labels beyond these signs other signs may be
applicable depend on the material and designation of decorative panel. (For details see ‘model list’ on page
3). The safety of the appliances is not influenced by these modifications.
Summary of testing:
Tests were conducted on models VENTS 100 Xstar 12
During the documentation check the English User’s Manual was evaluated.
Factory location: Ventilation Systems JSC 36, 40-Richchya Zhovtnya Str. Boyarka 08150, Kiev Region,
Ukraine.
The following standard amendments are added by MEEI in the Attachment 1:
- IEC 60335-1:2001 /A2: 2006
- IEC 60335-2-80:2002/A2: 2008;
- EN 60335-1:2002 /A2: 2006 +/A12: 2006, +/A13: 2008
- EN 60335-2-80:2003/A2: 2008
- EN 62233:2008
Attachments: 1: Standard amendments TRF (16 pages)
2: IEC 60598-2-1:1979+/A1: 1987 used in conjunction with IEC 60598-1: 2003+/A1: 2006
EN 60598-2-1: 1989 used in conjunction with EN 60598-1: 2004+/A1: 2006 TRF(28 pages)
3: Measuring equipment list (1 page)
This Test Report consists of three parts:
-
first part contains requirements of IEC 60335-2-80:2002 incl. A1:2004 in conjunction with IEC 603351:2001, incl. A1:2004; EN 60335-2-80:2003, incl. A1:2004 in conjunction with EN 60335-1:2002, incl.
A11:2004 and A1:2004 and EN 50366:2003 + A1:2006
-
second part (attachment 1) contains requirements of IEC 60335-2-80:2002/A2: 2008; EN 60335-280:2003/A2:2009, IEC 60335-1:2001 /A2: 2006, EN 60335-1:2002 /A2: 2006, EN 60335-1:2002 /A12:
2006, EN 60335-1:2002 /A13: 2008
-
third part (attachment 2) contains requirements of IEC 60598-2-1:1979+A1: 1987 in conjunction with
IEC 60598-1: 2003, IEC 60598-1: 2003/A1: 2006, EN 60598-2-1: 1989 in conjunction with EN 605981: 2004, EN 60598-1: 2004/A1: 2006
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 3 of 64
VENTS 100 Xstar 12
VENTS 100 Xstar 12 turbo
VENTS 100 Xstar 12 press
VENTS 100 Xstar 12 turbo press
VENTS 125 Xstar 12
VENTS 125 Xstar 12 turbo
VENTS 125 Xstar 12 press
VENTS 125 Xstar 12 turbo press
VENTS 150 Xstar 12
VENTS 150 Xstar 12 press
Rated
power
15 W
17 W
17 W
17 W
17 W
29 W
29 W
29 W
25 W
31 W
VENTS 100 Zstar 12 (XY)
VENTS 100 Zstar 12 turbo(XY)
VENTS 100 Zstar 12 press(XY)
VENTS 100 Zstar 12 turbo press (XY)
VENTS 125 Zstar 12 (XY)
VENTS 125 Zstar 12 turbo(XY)
VENTS 125 Zstar 12 press(XY)
VENTS 125 Zstar 12 turbo press (XY)
VENTS 150 Zstar 12 (XY)
VENTS 150 Zstar 12 press(XY)
15 W
17 W
17 W
17 W
17 W
29 W
29 W
29 W
25 W
31 W
Fan type
IP
protection
Report No.: 28207876 001
Class
IP 24
III
Motor type and manufacturer
BL 58-12E01
BL 58-16E01
BL 58-12E01
BL 58-16E01
BL 58-16E01
BL 58-30PE01
BL 58-16E01
BL 58-30PE01
BL 58-30PE01
BL 58-30PE01
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Shenzen Co. Ltd.
Hunan Keli Ltd.
Shenzen Co. Ltd.
Shenzen Co. Ltd.
Shenzen Co. Ltd.
BL 58-12E01
BL 58-16E01
BL 58-12E01
BL 58-16E01
BL 58-16E01
BL 58-30PE01
BL 58-16E01
BL 58-30PE01
BL 58-30PE01
BL 58-30PE01
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Hunan Keli Ltd.
Shenzen Co. Ltd.
Hunan Keli Ltd.
Shenzen Co. Ltd.
Shenzen Co. Ltd.
Shenzen Co. Ltd.
VENTS 100 ART 12 (XY)
VENTS 100 ART 12 turbo (XY)
VENTS 100 ART 12 press (XY)
VENTS 100 ART 12 turbo press (XY)
VENTS 125 ART 12 (XY)
VENTS 125 ART 12 turbo (XY)
VENTS 125 ART 12 press (XY)
VENTS 125 ART 12 turbo press (XY)
VENTS 150 ART 12 (XY)
VENTS 150 ART 12 press (XY)
14 W
BL 58-12E01
Hunan Keli Ltd.
16 W
BL 58-16E01
Hunan Keli Ltd.
16 W
BL 58-12E01
Hunan Keli Ltd.
16 W
BL 58-16E01
Hunan Keli Ltd.
16 W
BL 58-16E01
Hunan Keli Ltd.
IP X4
24 W
BL 58-30PE01
Shenzen Co. Ltd.
24 W
BL 58-16E01
Hunan Keli Ltd.
24 W
BL 58-30PE01
Shenzen Co. Ltd.
24 W
BL 58-30PE01
Shenzen Co. Ltd.
30 W
BL 58-30PE01
Shenzen Co. Ltd.
Voltage: 12 V; 50 Hz. All motor provided with 150 °C thermally protector. Tests were conducted on
models VENTS 100 Xstar 12. The structures of engines are basically same as the engine of unit
type VENTS 100 Xstar 12.
Models differ in model name, shape of enclosure, rated power, light source and degree of protection.
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 4 of 64
Report No.: 28207876 001
Test item particulars .................................................. : Classification of installation and use ............................ : Class III
Supply Connection........................................................ : Permanent connection, supply cord is not provided
Possible test case verdicts:
- test case does not apply to the test object..................: N/A
- test object does meet the requirement .......................: P(Pass)
- test object does not meet the requirement .................: F(Fail)
Testing ..........................................................................:
Date of receipt of test item ............................................: 16-11-2009
Date (s) of performance of tests ...................................: 16-11-2009 – 14-01-2009
General remarks:
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
General product information:
The fans are designed for ventilation of domestic and similar purposes and for continuous operation.
Meaning of characters in type references:
VENTS yyy M 12 w XY
‘VENTS’: trade mark
‘yyy’: the diameter of the duct [mm]. It can be: 100, 125, 150
‘M’: indication of the series. It can be: Xstar, Zstar, ART (Xstar: fan with a light source and
without a decorative panel; Zstar: fan with a light source and with a decorative panel;
ART: fan without light source and with a decorative panel)
‘12’: Voltage: 12 V~
‘w’ can be: blank, press, turbo, turbo press
press: increased press
turbo: motor with increased power is installed
-
'XY’ (not for Xstar):
X:
Y:
TRF No. IEC60335_2_80B_mod
Material of the decorative panel. It can be: blank (stainless steel),
1 (Glass); 2 (Organic glass);
Design option of the decorative panel: Digital designation from 0 up
to 9.
TRF originator: KEMA
www.tuv.com
Page 5 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
5
GENERAL CONDITIONS FOR THE TESTS
P
Tests performed according to cl. 5, e.g. nature of
supply, sequence of testing, etc.
P
5.7
Result - Remark
Verdict
Fans to be used in tropical climates, the tests of
clause 10, 11 and 13 are carried out at 40°C +/- 2°C
(IEC 60335-2-80)
Not for tropical climates.
Fans to be marked with ambient operating
temperature, the tests of clause 10, 11 and 13 are
carried out at the marked value +/- 2°C
(IEC 60335-2-80)
Test of Clause 10, 11 and 13
are performed on the
temperature of 45°C
N/A
P
6
CLASSIFICATION
6.1
Protection against electric shock:
Class 0, 0I, I, II, III ..................................................... :
Class III
(see Group differences too)
P
6.2
Protection against harmful ingress of water
IP X4
P
P
Duct fans shall be at least IP X2 (IEC 60335-2-80)
N/A
For temperate climate.
P
6.101
Classification to climatic conditions : temperature
climates, tropical climates (IEC 60335-2-80)
7
MARKING AND INSTRUCTIONS
7.1
Rated voltage or voltage range (V) ........................... :
12 (SELV)
P
Nature of supply......................................................... :
~
P
Rated frequency (Hz) ................................................ :
50
P
Rated power input (W) .............................................. :
For details see ‘model list’ on
page 3.
P
Rated current (A) ...................................................... :
Rated power stated.
Manufacturer's or responsible vendor's name,
trademark or identification mark................................ :
VENTS
P
Model or type reference............................................. :
See copy of marking plate.
P
Symbol 5172 of IEC 60417, for Class II appliances
See copy of marking plate.
P
IP number, other than IP X0...................................... :
IP 24; IP X4 (ART)
P
Symbol IEC 60417-5036, for the enclosure of
electrically-operated water valves in external hosesets for connection of an appliance to the water
mains
No water valve.
TRF No. IEC60335_2_80B_mod
P
N/A
N/A
TRF originator: KEMA
www.tuv.com
Page 6 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
For tropical climates marked with letter T
(IEC 60335-2-80)
Not for tropical climates.
Fans intended for operation in locations where the
local ambient temperature exceeds 40°C marked
with ambient operating temperature (IEC 60335-280)
45 °C is marked as Tmax.
N/A
P
Warning for stationary appliances for multiple supply
N/A
Warning placed in vicinity of terminal cover
N/A
Range of rated values marked with the lower and
upper limits separated by a hyphen
N/A
Different rated values marked with the values
separated by an oblique stroke
N/A
7.4
Appliances adjustable for different rated voltages, the Not adjustable.
voltage setting is clearly discernible
N/A
7.5
Appliances with more than one rated voltage or one
or more rated voltage ranges, marked with rated
input or rated current for each rated voltage or range,
unless
N/A
the power input is related to the mean value of the
rated voltage range
N/A
Relation between marking for upper and lower limits
of rated power input or rated current and voltage is
clear
N/A
7.2
7.3
7.6
Correct symbols used
7.7
Connection diagram fixed to appliances to be
connected to more than two supply conductors and
appliances for multiple supply
7.8
Except for type Z attachment, terminals for connection to the supply mains indicated
as follows:
P
N/A
P
- marking of terminals exclusively for the neutral
conductor (N)
N/A
- marking of protective earthing terminals (symbol
5019 of IEC 60417)
N/A
- marking not placed on removable parts
P
7.9
Marking or placing of switches which may cause a
hazard
No such switch.
N/A
7.10
Indications of switches on stationary appliances and
controls on all appliances by use of figures, letters or
other visual means .................................................... :
-
N/A
The figure 0 indicates only OFF position, unless no
confusion with the OFF position
TRF No. IEC60335_2_80B_mod
N/A
TRF originator: KEMA
www.tuv.com
Page 7 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
7.11
Indication for direction of adjustment of controls
7.12
Instructions for safe use provided
P
7.12.1
Sufficient details for installation supplied
P
Type or model number of luminaries which may be
installed for fans intended for this purpose
(IEC 60335-2-80)
P
For partition fans, if intended for mounting in outside
walls or windows (IEC 60335-2-80)
Result - Remark
Verdict
N/A
N/A
No partition fans.
N/A
For fans intended to be mounted at high level, fan
has to be installed so that the blades are more than
2.3 m above the floor, or windows
(IEC 60335-2-80)
For duct and partition fans precautions taken to avoid User’s Manual “Safety
back flow of gases into the room
requirements” states the
(IEC 60335-2-80)
necessary warning
P
N/A
If the instructions state that the guard has to be
No guard.
removed for cleaning purposes, the instructions shall
state the substance of the following:
“Ensure that the fan is switched off from the supply
mains before removing guard.”
(IEC 60335-2-80)
7.12.2
Stationary appliances not fitted with means for
User’s Manual “Preparation to
disconnection from the supply mains having a
device operation” states the
contact separation in all poles that provide full
necessary disconnection
disconnection under overvoltage category III, the
instructions state that means for disconnection must
be incorporated in the fixed wiring in accordance with
the wiring rules
7.12.3
Insulation of the fixed wiring in contact with parts
exceeding 50 K during clause 11; instructions stating
that the fixed wiring must be protected
N/A
7.12.4
Instructions for built-in appliances:
N/A
- dimensions of space
No built-in appliances.
P
N/A
- dimensions and position of supporting means
N/A
- distances between parts and surrounding structure
N/A
- dimensions of ventilation openings and
arrangement
N/A
- connection to supply mains and interconnection of
separate components
N/A
- allow disconnection of the appliance after
installation, by accessible plug or a switch in the fixed
wiring, unless
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 8 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
a switch complying with 24.3
N/A
Replacement cord instructions, type X attachment
with a specially prepared cord
N/A
Replacement cord instructions, type Y attachment
N/A
Replacement cord instructions, type Z attachment
N/A
7.12.6
Caution in the instructions for heating appliances with No heating appliances.
a non-self-resetting thermal cut-out
N/A
7.12.7
Instructions for fixed appliances stating how the
appliance is to be fixed
7.12.8
Instructions for appliances connected to the water mains:
N/A
- max. inlet water pressure (Pa) ................................ :
No water mains.
N/A
- min. inlet water pressure, if necessary (Pa)............ :
-
N/A
7.12.5
P
N/A
Instructions concerning new and old hose-sets for
appliances connected to the water mains by
detachable hose-sets
7.13
Instructions and other texts in an official language
7.14
Marking clearly legible and durable
P
7.15
Marking on a main part
P
Marking clearly discernible from the outside, if
necessary after removal of a cover
English and German language
provided.
Marking label repeated inside
too.
P
P
For portable appliances, cover can be removed or
opened without a tool
N/A
For stationary appliances, name, trademark or
identification mark and model or type reference
visible after installation
N/A
For fixed appliances, name, trademark or
identification mark and model or type reference
visible after installation according to the instructions
P
Indications for switches and controls placed on or
near the components. Marking not on parts which
can be positioned or repositioned in such a way that
the marking is misleading
N/A
7.16
Marking of a possible replaceable thermal link or fuse Non-replaceable thermal link
link clearly visible with regard to replacing the link
provided.
N/A
8
PROTECTION AGAINST ACCESS TO LIVE PARTS
P
8.1
Adequate protection against accidental contact with
live parts
P
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 9 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
8.1.1
Requirement applies for all positions, detachable
parts removed
N/A
Insertion or removal of lamps, protection against
contact with live parts of the lamp cap
N/A
Use of test probe B of IEC 61032: no contact with live
parts
N/A
8.1.2
Use of test probe 13 of IEC 61032 through openings
in class 0 appliances and class II appliances/
constructions: no contact with live parts
Result - Remark
Verdict
N/A
No contact.
N/A
Test probe 13 also applied through openings in
earthed metal enclosures having a non-conductive
coating: no contact with live parts
For appliances other than class II, use of test probe
41 of IEC 61032: no contact with live parts of visible
glowing heating elements
8.1.4
Accessible part not considered live if:
P
- safety extra-low a.c. voltage: peak value not
exceeding 42.4 V
P
8.1.5
8.2
No heating elements
N/A
8.1.3
- safety extra-low d.c. voltage: not exceeding 42.4 V
N/A
- or separated from live parts by protective
impedance
N/A
If protective impedance: d.c. current not exceeding
2 mA, and
N/A
a.c. peak value not exceeding 0.7 mA
N/A
- for peak values over 42.4 V up to and including
450 V, capacitance not exceeding 0,1 µF
N/A
- for peak values over 450 V up to and including
15 kV, discharge not exceeding 45 µC
N/A
Live parts protected at least by basic insulation before installation or assembly:
N/A
- built-in appliances
N/A
- fixed appliances
N/A
- appliances delivered in separate units
N/A
Class II appliances and constructions constructed so
that there is adequate protection against accidental
contact with basic insulation and metal parts
separated from live parts by basic insulation only
N/A
Only possible to touch parts separated from live parts
by double or reinforced insulation
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 10 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
9
Requirement - Test
Result - Remark
Verdict
After the removal of detachable parts for the
purposes of user maintenance, the basic insulation of
internal wiring may be touched provided that it is
electrically equivalent to the insulation of cords
complying with IEC 60227 or IEC 61245.
(IEC 60335-2-80)
N/A
STARTING OF MOTOR-OPERATED APPLIANCES
N/A
Requirements and tests are specified in part 2 when
necessary
N/A
10
POWER INPUT AND CURRENT
10.1
Power input at normal operating temperature, rated
voltage and normal operation not deviating from
rated power input by more than shown in table 1
P
(See appended table)
N/A
Shutters or similar devices are in open position
(IEC 60335-2-80)
10.2
Current at normal operating temperature, rated
voltage and normal operation not deviating from
rated current by more than shown in table 2
P
Rated current is not marked.
N/A
N/A
Shutters or similar devices are in open position
(IEC 60335-2-80)
11
HEATING
P
11.1
No excessive temperatures in normal use
P
11.2
Placing and mounting of appliance as described
P
11.3
Temperature rises, other than of windings,
determined by thermocouples
P
Temperature rises of windings determined by
resistance method, unless
P
the windings makes it difficult to make the necessary
connections
N/A
11.4
Heating appliances operated under normal operation No heating appliances.
at 1.15 times rated power input ................................ :
N/A
11.5
Motor-operated appliances operated under normal
12,7 V
operation at most unfavourable voltage between 0.94
and 1.06 times rated voltage..................................... :
11.6
Combined appliances operated under normal
operation at most unfavourable voltage between 0.94
and 1.06 times rated voltage..................................... :
TRF No. IEC60335_2_80B_mod
P
N/A
TRF originator: KEMA
www.tuv.com
Page 11 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
11.7
Operation until steady conditions are established
(IEC 60335-2-80)
11.8
Temperature rises not exceeding values in table 3
Result - Remark
Verdict
P
(See appended tables)
Sealing compound does not flow out
P
P
Protective devices do not operate, except
P
components in protective electronic circuits tested for
the number of cycles specified in 24.1.4
N/A
Fans for tropical climates: Temperature limits are
reduced by 15 K (IEC 60335-2-80)
N/A
The temperature rise limits for fans marked with an
ambient operating temperature are reduced by the
difference between the marked value and 25°C
(IEC 60335-2-80)
Temperature limits reduced by
20 K, see appended table.
P
13
LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING
TEMPERATURE
P
13.1
Leakage current not excessive and electric strength
adequate
P
Heating appliances operated at 1.15 times rated
power input ................................................................ :
N/A
-
Motor-operated appliances and combined appliances 12,7 V
supplied at 1.06 times rated voltage ......................... :
13.2
Protective impedance and radio interference filters
disconnected before carrying out the tests
N/A
Leakage current measured by means of the circuit
described in figure 4 of IEC 60990
P
Leakage current measurements
13.3
P
(See appended table)
The appliance is disconnected from the supply
Electric strength tests according to table 4
P
(See appended table)
No breakdown during the tests
14
P
P
P
TRANSIENT OVERVOLTAGES
N/A
Appliances withstand the transient overvoltages to
which they may be subjected
N/A
Clearances having a value less than specified in
Clearances are not less than
table 16 subjected to an impulse voltage test, the test specified.
voltage specified in table 6
N/A
No flashover during the test, unless of functional
insulation
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 12 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
N/A
In case of flashover of functional insulation, the
appliance complies with clause 19 with the clearance
short circuited
15
MOISTURE RESISTANCE
P
15.1
Enclosure provides the degree of moisture protection
according to classification of the appliance
P
Compliance checked as specified in 15.1.1, taking
into account 15.1.2, followed by the electric strength
test of 16.3
P
No trace of water on insulation which can result in a
reduction of clearances and creepage distances
below values specified in clause 29
P
15.1.1
Appliances, other than IPX0, subjected to tests as
specified in IEC 60529..............................................:
Tested for IPX4.
Water valves in external hoses for connection of an
appliance to the water mains tested as specified for
IPX7 appliances
N/A
Outer part of fans mounted in external structure of a
building, subjected to clause 14.2.4(a) of IEC 60529
(IEC 60335-2-80)
N/A
Fans marked with the second numeral of the IP
Tested for IPX4.
system are subjected to the appropriate of IEC 60529
both at rest and in operation while supplied at rated
voltage (IEC 60335-2-80)
15.1.2
P
P
Hand-held appliance turned continuously through the
most unfavourable positions during the test
N/A
Built-in appliances installed according to the
instructions
N/A
Appliances placed or used on the floor or table
placed on a horizontal unperforated support
N/A
Appliances normally fixed to a wall and appliances
with pins for insertion into socket-outlets are mounted
on a wooden board
N/A
For IPX3 appliances, the base of wall mounted
appliances is placed at the same level as the pivot
axis of the oscillating tube
N/A
For IPX4 appliances, the horizontal centre line of the
appliance is aligned with the pivot axis of the
oscillating tube
TRF No. IEC60335_2_80B_mod
P
TRF originator: KEMA
www.tuv.com
Page 13 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
15.2
Requirement - Test
Verdict
However, for appliances normally used on the floor or
table, the movement is limited to two times 90° for a
period of 5 min, the support being placed at the level
of the pivot axis of the oscillating tube
N/A
Appliances normally fixed to a ceiling are mounted
underneath a horizontal unperforated support, the
pivot axis of the oscillating tube located at the level of
the underside of the support
N/A
For IPX4 appliances, the movement of the tube is
limited to two times 90° from the vertical for a period
of 5 min
P
Wall-mounted appliances, take into account the
distance to the floor stated in the instructions
N/A
Appliances with type X attachment fitted with a
flexible cord as described
N/A
Detachable parts tested as specified
N/A
Spillage of liquid does not affect the electrical
insulation
No spillage in normal condition.
N/A
Appliances with type X attachment fitted with a
flexible cord as described
N/A
Appliances incorporating an appliance inlet tested
with or without an connector, whichever is most
unfavourable
N/A
Detachable parts removed
N/A
Overfilling test with additional amount of
water, over a period of 1 min (l)................................. :
15.3
Result - Remark
-
N/A
The appliance withstands the electric strength test of
16.3
N/A
No trace of water on insulation that can result in a
reduction of clearances and creepage distances
below values specified in clause 29
N/A
Appliances proof against humid conditions
48h, 95%, 25°C
P
Humidity test for 48 h in a humidity cabinet
P
The appliance withstands the tests of clause 16
P
16
LEAKAGE CURRENT AND ELECTRIC STRENGTH
P
16.1
Leakage current not excessive and electric strength
adequate
P
Protective impedance disconnected from live parts
before carrying out the tests
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 14 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
16.2
Single-phase appliances: test voltage 1.06 times
rated voltage .............................................................. :
12,7
Three-phase appliances: test voltage 1.06 times
rated voltage divided by √3........................................ :
-
Leakage current measurements
(See appended table)
P
Electric strength tests according to table 7
(See appended table)
P
16.3
Verdict
P
N/A
No breakdown during the tests
17
18
P
OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS
N/A
No excessive temperatures in transformer or
associated circuits in event of short-circuits likely to
occur in normal use
No transformers.
N/A
Appliance supplied with 1.06 or 0.94 times rated
voltage and the most unfavourable short-circuit or
overload likely to occur in normal use applied .......... :
-
N/A
Temperature rise of insulation of the conductors of
safety extra-low voltage circuits not exceeding the
relevant value specified in table 3 by more than 15 K
N/A
Temperature of the winding not exceeding the value
specified in table 8,
N/A
however limits do not apply to fail-safe transformers
complying with sub-clause 15.5 of IEC 61558-1
N/A
ENDURANCE
N/A
Requirements and tests are specified in part 2 when
necessary
Not applicable.
N/A
19
ABNORMAL OPERATION
P
19.1
The risk of fire or mechanical damage under
abnormal or careless operation obviated
P
Electronic circuits so designed and applied that a
fault will not render the appliance unsafe
P
Fans incorporating shutters or similar subjected to
the test of cl. 19.101 (IEC 60335-2-80)
See cl. 19.101.
N/A
19.2
Test of appliance with heating elements with
restricted heat dissipation; test voltage (V): power
input of 0.85 times rated power input........................ :
-
N/A
19.3
Test of 19.2 repeated; test voltage (V): power input of 1.24 times rated power input..................................... :
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 15 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
19.4
Test conditions as in cl. 11, any control limiting the
temperature during tests of cl. 11 short-circuited
N/A
19.5
Test of 19.4 repeated on Class 0I and I appliances
with tubular sheathed or embedded heating
elements. No short-circuiting, but one end of the
element connected to the elements sheath
N/A
The test repeated with reversed polarity and the other
end of the heating element connected to the sheath
N/A
The test is not carried out on appliances intended to
be permanently connected to fixed wiring and on
appliances where an all-pole disconnection occurs
during the test of 19.4
N/A
19.6
Appliances with PTC heating elements tested at
rated voltage, establishing steady conditions
Result - Remark
No PTC.
Stalling test by locking the rotor if the locked rotor
torque is smaller than the full load torque or locking
moving parts of other appliances
Locked rotor, motor capacitors open-circuited or
short-circuited, if required
N/A
N/A
The working voltage of the PTC heating element is
increased by 5% and the appliance is operated until
steady conditions are re-established. The voltage is
then increased in similar steps until 1.5 times working
voltage or until the PTC heating element ruptures
19.7
Verdict
P
No motor-capacitor.
N/A
Locked rotor, capacitors open-circuited one at a time
N/A
Test repeated with capacitors short-circuited one at a
time, if required
N/A
Appliances with timer or programmer supplied with
rated voltage for each of the tests, for a period equal
to the maximum period allowed
N/A
Other appliances supplied with rated voltage for a
period as specified
Separate controls are mounted on a dull-black
plywood board (IEC 60335-2-80)
P
No such controls.
N/A
Approximately 50% of the area of each ventilation
opening is blocked (IEC 60335-2-80)
N/A
Winding temperatures not exceeding values
specified in table 8
N/A
Temperature of the dull black-painted board for the
separate control do not exceed:
- 50K, for appliance with T marking
- 65K, for other appliances (IEC 60335-2-80)
TRF No. IEC60335_2_80B_mod
No such controls.
N/A
TRF originator: KEMA
www.tuv.com
Page 16 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
19.8
Three-phase motors operated at rated voltage with
one phase disconnected
Single-phase motors.
N/A
19.10
Series motor operated at 1.3 times rated voltage for
1 min .......................................................................... :
No series motor.
N/A
19.11
19.11.1
19.11.2
Verdict
During the test, parts not being ejected from the
appliance
N/A
Electronic circuits, compliance checked by evaluation
of the fault conditions specified in 19.11.2 for all
circuits or parts of circuits, unless they comply with
the conditions specified in 19.11.1
N/A
Appliances incorporating a protective electronic
circuit subjected to the tests of 19.11.3 and 19.11.4
N/A
Appliances having a switch with an off position
obtained by electronic disconnection, or a switch
placing the appliance in a stand-by mode, subjected
to the tests of 19.11.4
N/A
Before applying the fault conditions a) to f) in 19.11.2, it is checked if circuits or parts of
circuit meet both of the following conditions:
N/A
- the electronic circuit is a low-power circuit, that is,
the maximum power at low-power points does not
exceed 15 W according to the tests specified
N/A
- the protection against electric shock, fire hazard,
mechanical hazard or dangerous malfunction in other
parts of the appliance does not rely on the correct
functioning of the electronic circuit
N/A
Fault conditions applied one at a time, the appliance operated under conditions
specified in cl. 11, but supplied at rated voltage, the duration of the tests as specified:
N/A
a) short circuit of functional insulation if clearances or
creepage distances are less than the values
specified in 29
N/A
b) open circuit at the terminals of any component
N/A
c) short circuit of capacitors, unless they comply with
IEC 60384-14
N/A
d) short circuit of any two terminals of an electronic
component, other than integrated circuits. This fault
condition is not applied between the two circuits of an
optocoupler
N/A
e) failure of triacs in the diode mode
N/A
No such triacs.
N/A
f) failure of an integrated circuit
19.11.3
If the appliance incorporates a protective electronic
circuit which operates to ensure compliance with
clause 19, the relevant test is repeated with a single
fault simulated, as indicated in a) to f) of 19.11.2
TRF No. IEC60335_2_80B_mod
No protective electronic circuit.
N/A
TRF originator: KEMA
www.tuv.com
Page 17 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
During and after each test the following is checked:
N/A
- the temperature rise of the windings do not exceed
the values specified in table 8
N/A
- the appliance complies with the conditions specified
in 19.13
N/A
- any current flowing through protective impedance
not exceeding the limits specified in 8.1.4
N/A
If a conductor of a printed board becomes open-circuited, the appliance is considered
to have withstood the particular test, provided all three of the following conditions are
met:
N/A
- the material of the printed circuit board withstands
the burning test of annex E
N/A
- any loosened conductor does not reduce the
clearances or creepage distances between live parts
and accessible metal parts below the values
specified in cl. 29
N/A
- the appliance withstands the tests of 19.11.2 with
open-circuited conductor bridged
N/A
Appliances having a switch with an off position
obtained by electronic disconnection, or
N/A
a switch that can be placed in the stand-by mode,
N/A
subjected to the tests of 19.11.4.1 to 19.11.4.7
N/A
Appliances incorporating a protective electronic
circuit subjected to the tests of 19.11.4.1 to 19.11.4.7,
except that
N/A
appliances operated for 30 s or 5 min during the test
of 19.7 are not subjected to the tests for
electromagnetic phenomena.
N/A
19.11.4.1
The appliance is subjected to electrostatic discharges
in accordance with IEC 61000-4-2, test level 4
N/A
19.11.4.2
The appliance is subjected to radiated fields in
accordance with IEC 61000-4-3, test level 3
N/A
19.11.4.3
The appliance is subjected to fast transient bursts in
accordance with IEC 61000-4-4, test level 3 or 4 as
specified
N/A
19.11.4.4
The power supply terminals of the appliance
subjected to voltage surges in accordance with IEC
61000-4-5, test level 3 or 4 as specified
N/A
Earthed heating elements in class I appliances
disconnected
N/A
The appliance is subjected to injected currents in
accordance with IEC 61000-4-6, test level 3
N/A
19.11.4
19.11.4.5
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 18 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
19.11.4.6
The appliance is subjected to voltage dips and
interruptions in accordance with IEC 61000-4-11
N/A
19.11.4.7
The appliance is subjected to mains signals in
accordance with IEC 61000-4-13, test level class 2
N/A
19.12
If the safety of the appliance for any of the fault
conditions specified in 19.11.2 depends on the
operation of a miniature fuse-link complying with
IEC 60127, the test is repeated, measuring the
current flowing through the fuse-link; measured
current (A); rated current of the fuse-link (A) ............ :
19.13
During the tests the appliance does not emit flames,
molten metal, poisonous or ignitable gas in
hazardous amounts
Temperature rises not exceeding the values shown
in table 9
Result - Remark
Verdict
N/A
None.
P
(See appended table)
Enclosures not deformed to such an extent that
compliance with cl. 8 is impaired
P
N/A
If the appliance can still be operated it complies with
20.2
Insulation, other than of class III appliance, withstand the electric strength test of 16.3,
the test voltage specified in table 4:
P
- basic insulation........................................................ :
500 V
P
- supplementary insulation ........................................ :
-
N/A
- reinforced insulation ................................................ :
-
N/A
The appliance does not undergo a dangerous
malfunction, and
P
no failure of protective electronic circuits, if the
appliance is still operable
N/A
Appliances tested with an electronic switch in the off
position or in the stand-by mode, do not become
operational
N/A
19.101
Fans incorporating shutters or similar that are
operated automatically are supplied at rated voltage
in the closed or open position, whichever is more
unfavourable (IEC 60335-2-80)
20
STABILITY AND MECHANICAL HAZARDS
20.1
P
Adequate stability
TRF No. IEC60335_2_80B_mod
No shutter
N/A
Appliance shall be installed
properly according to the
User’s Manual.
N/A
P
TRF originator: KEMA
www.tuv.com
Page 19 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Verdict
Tilting test through an angle of 10° (appliance placed
on an inclined plane/horizontal plane); appliance
does not overturn
N/A
Tilting test repeated on appliances with heating
elements, angle of inclination increased to 15°
N/A
Possible heating test in overturned position;
temperature rise does not exceed values shown in
table 9
N/A
Portable pedestal fans exceeding 1,7 m and
exceeding 10 kg tested with a force of 40 N at 1,5 m
(IEC 60335-2-80)
20.2
Result - Remark
N/A
No such fans.
Moving parts adequately arranged or enclosed as to
provide protection against personal injury
P
Protective enclosures, guards and similar parts are
non-detachable
P
Adequate mechanical strength and fixing of
protective enclosures
P
Self-resetting thermal cut-outs and overcurrent
protective devices not causing a hazard, by
unexpected reclosure
N/A
No such cut-outs.
Not possible to touch dangerous moving parts with
test probe
P
20.101
Fan blades, other than those for mounting at high
level, shall be guarded, unless
(IEC 60335-2-80)
21
MECHANICAL STRENGTH
P
21.1
Appliance has adequate mechanical strength and is
constructed as to withstand rough handling
P
Checked by applying blows to the appliance in
accordance with test Ehb of IEC 60068-2-75, spring
hammer test, impact energy 0,5 J
P
If necessary, supplementary or reinforced insulation
subjected to the electric strength test of 16.3
N/A
If necessary, repetition of groups of three blows on a
new sample
N/A
Accessible parts of solid insulation having strength to
prevent penetration by sharp implements
P
21.2
The insulation is tested as specified, unless
the thickness of supplementary insulation is at least 1
mm and reinforced insulation is at least 2 mm
TRF No. IEC60335_2_80B_mod
Blades are guarded after the
installation according the
User’s Manual by the duct
P
N/A
P
TRF originator: KEMA
www.tuv.com
Page 20 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
21.101
Fan guards are subjected to a push and pull force of
20 N. Dangerous moving parts are not accessible
(IEC 60335-2-80)
Blades are guarded after the
installation according the
User’s Manual by the duct
21.102
Ceiling fans have adequate strength.
(IEC 60335-2-80)
No such fans.
22
Verdict
N/A
Load four times the mass of the fan is suspended
from the body of the fan for 1 min.
(IEC 60335-2-80)
N/A
A torque of 1 Nm is then applied to the fixed body of
the fan for 1 min. The test is repeated with the torque
applied the reverse direction.
(IEC 60335-2-80)
N/A
CONSTRUCTION
P
N/A
22.1
Appliance marked with the first numeral of the IP
system, relevant requirements of IEC 60529 are
fulfilled
22.2
Stationary appliance: means to provide all-pole disconnection from the supply
provided, the following means being available:
- a switch complying with 24.3
No switch with all-pole
disconnection.
- a statement in the instruction sheet that a
Statement in the User’s
disconnection incorporated in the fixed wiring is to be Manual.
provided
- an appliance inlet
No appliance inlet.
N/A
P
N/A
N/A
Singe-pole switches and single-pole protective
devices for the disconnection of heating elements in
single-phase permanently connected class I
appliances, connected in the phase conductor
Appliance provided with pins: no undue strain on
socket-outlets
P
N/A
- a supply cord fitted with a plug
22.3
P
No pins.
N/A
Applied torque not exceeding 0.25 Nm
N/A
Pull force of 50N to each pin after the appliance has
being placed in the heating cabinet; when cooled to
room temperature the pins are not displaced by more
than 1mm
N/A
Each pin subjected to a torque of 0.4Nm; the pins are
not rotating unless rotating does not impair
compliance with the standard
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 21 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
22.4
Appliance for heating liquids and appliance causing
undue vibration not provided with pins for insertion
into socket-outlets
No such appliance.
22.5
No risk of electric shock when touching the pins of
the plug, the appliance being disconnected from the
supply at the instant of voltage peak.
N/A
22.6
Electrical insulation not affected by condensing water
or leaking liquid
N/A
Electrical insulation of Class II appliances not
affected in case of a hose rupture or seal leak
N/A
N/A
22.7
Adequate safeguards against the risk of excessive
pressure in appliances provided with steamproducing devices
No steam.
N/A
22.8
Electrical connections not subject to pulling during
cleaning of compartments to which access can be
gained without the aid of a tool, and that are likely to
be cleaned in normal use
No such cleaning.
N/A
22.9
Insulation, internal wiring, windings, commutators
and slip rings not exposed to oil, grease or similar
substances
P
Adequate insulating properties of oil or grease to
which insulation is exposed
N/A
22.10
22.11
Not possible to reset voltage-maintained non-selfresetting thermal cut-outs by the operation of an
automatic switching device incorporated within the
appliance
N/A
Non-self resetting thermal motor protectors have a
trip-free action, unless
N/A
they are voltage maintained
N/A
Location or protection of reset buttons of non-selfresetting controls is so that accidental resetting is
unlikely
N/A
Reliable fixing of non-detachable parts that provide
the necessary degree of protection against electric
shock, moisture or contact with moving parts
P
Obvious locked position of snap-in devices used for
fixing such parts
N/A
No deterioration of the fixing properties of snap-in
devices used in parts that are likely to be removed
during installation or servicing
N/A
Tests as described
22.12
No such kind of devices.
Handles, knobs etc. fixed in a reliable manner
TRF No. IEC60335_2_80B_mod
P
N/A
TRF originator: KEMA
www.tuv.com
Page 22 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Fixing in wrong position of handles, knobs etc.
indicating position of switches or similar components
not possible
N/A
Axial force 15 N applied to parts, the shape being so
that an axial pull is unlikely to be applied
N/A
Axial force 30 N applied to parts, the shape being so
that an axial pull is likely to be applied
N/A
22.13
Unlikely that handles, when gripped as in normal use,
make the operators hand touch parts having a
temperature rise exceeding the value specified for
handles which are held for short periods only
N/A
22.14
No ragged or sharp edges creating a hazard for the
user in normal use, or during user maintenance
Verified by visual inspection.
P
No exposed pointed ends of self tapping screws etc.,
liable to be touched by the user in normal use or
during user maintenance
P
22.15
Storage hooks and the like for flexible cords smooth
and well rounded
N/A
22.16
Automatic cord reels cause no undue abrasion or
damage to the sheath of the flexible cord, no
breakage of conductors strands, no undue wear of
contacts
No automatic cord reel.
N/A
Cord reel tested with 6000 operations, as specified
N/A
Electric strength test of 16.3, voltage of 1000 V
applied
N/A
No spacers.
N/A
22.17
Spacers not removable from the outside by hand or
by means of a screwdriver or a spanner
22.18
Current-carrying parts and other metal parts resistant
to corrosion under normal conditions of use
22.19
Driving belts not used as electrical insulation
22.20
Direct contact between live parts and thermal
insulation effectively prevented, unless material used
is non-corrosive, non-hygroscopic and noncombustible
N/A
Compliance is checked by inspection and, if
necessary, by appropriate test
N/A
P
No driving belt.
N/A
22.21
Wood, cotton, silk, ordinary paper and fibrous or
hygroscopic material not used as insulation, unless
impregnated
No such material.
P
22.22
Appliances not containing asbestos
No asbestos.
P
22.23
Oils containing polychlorinated biphenyl (PCB) not
used
TRF No. IEC60335_2_80B_mod
P
TRF originator: KEMA
www.tuv.com
Page 23 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
22.24
Bare heating elements adequately supported
No heating elements.
N/A
In case of rupture, the heating conductor is unlikely to
come in contact with accessible metal parts
N/A
22.25
Sagging heating conductors cannot come into
contact with accessible metal parts
N/A
22.26
The insulation between parts operating at safety
extra-low voltage and other live parts complies with
the requirements for double or reinforced insulation
No such parts.
N/A
22.27
Parts connected by protective impedance separated
by double or reinforced insulation
No protective impedance.
N/A
22.28
Metal parts of Class II appliances conductively
connected to gas pipes or in contact with water:
separated from live parts by double or reinforced
insulation
N/A
22.29
Class II appliances permanently connected to fixed
wiring so constructed that the required degree of
access to live parts is maintained after installation
N/A
22.30
Parts serving as supplementary or reinforced
insulation fixed so that they cannot be removed
without being seriously damaged, or
N/A
so constructed that they cannot be replaced in an
incorrect position, and so that if they are omitted, the
appliance is rendered inoperable or manifestly
incomplete
N/A
Clearances and creepage distances over
supplementary and reinforced insulation not reduced
below values specified in clause 29 as a result of
wear
N/A
Clearances and creepage distances between live
parts and accessible parts not reduced below values
for supplementary insulation, if wires, screws etc.
become loose
N/A
Supplementary and reinforced insulation designed or
protected against deposition of dirt or dust
N/A
Supplementary insulation of natural or synthetic
rubber resistant to ageing, or arranged and
dimensioned so that creepage distances are not
reduced below values specified in 29.2
N/A
Ceramic material not tightly sintered, similar material
or beads alone not used as supplementary or
reinforced insulation
N/A
Oxygen bomb test at 70 °C for 96 h and 16 h at room
temperature
N/A
22.31
22.32
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 24 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
22.33
Conductive liquids that are or may become
No liquid.
accessible in normal use are not in direct contact with
live parts
N/A
Electrodes not used for heating liquids
N/A
For class II constructions, conductive liquids that are
or may become accessible in normal use, not in
direct contact with basic or reinforced insulation
N/A
For class II constructions, conductive liquids which
are in contact with live parts, not in direct contact with
reinforced insulation
N/A
22.34
Shafts of operating knobs, handles, levers etc. not
live, unless the shaft is not accessible when the part
is removed
N/A
22.35
Handles, levers and knobs, held or actuated in
normal use, not becoming live in the event of an
insulation fault
N/A
Not hand-held use.
Such parts being of metal, and their shafts or fixings
are likely to become live in the event of an insulation
fault, they are either adequately covered by insulation
material, or their accessible parts are separated from
their shafts or fixings by supplementary insulation
N/A
This requirement does not apply to handles, levers
and knobs on stationary appliances other than those
of electrical components, provided they are either
reliably connected to an earthing terminal or earthing
contact, or separated from live parts by earthed metal
N/A
N/A
22.36
Handles continuously held in the hand in normal use
are so constructed that when gripped as in normal
use, the operators hand is not likely to touch metal
parts, unless they are separated from live parts by
double or reinforced insulation
22.37
Capacitors in Class II appliances not connected to
accessible metal parts, unless complying with 22.42
N/A
Metal casings of capacitors in Class II appliances
separated from accessible metal parts by
supplementary insulation, unless complying with
22.42
N/A
22.38
Capacitors not connected between the contacts of a
thermal cut-out
N/A
22.39
Lamp holders used only for the connection of lamps
P
22.40
Motor-operated appliances and combined appliances Not movable appliance.
intended to be moved while in operation, or having
accessible moving parts, fitted with a switch to control
the motor. The actuating member of the switch being
easily visible and accessible
TRF No. IEC60335_2_80B_mod
Not hand-held use.
N/A
TRF originator: KEMA
www.tuv.com
Page 25 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
22.41
No components, other than lamps, containing
mercury
No mercury.
22.42
Protective impedance consisting of at least two
separate components
N/A
Values specified in 8.1.4 not exceeded if any one of
the components are short-circuited or open-circuited
N/A
P
N/A
22.43
Appliances adjustable for different voltages,
accidental changing of the setting of the voltage
unlikely to occur
Not adjustable.
22.44
Appliances are not allowed to have an enclosure that Not like a toy.
is shaped and decorated so that the appliance is
likely to be treated as a toy by children
22.45
When air is used as reinforced insulation, clearances
not reduced below the values specified in 29.1.4 due
to deformation as a result of an external force applied
to the enclosure
22.46
Software used in protective electronic circuits is
software class B or C ............................................... :
No software.
N/A
22.47
Appliances connected to the water mains withstand
the water pressure expected in normal use
No connection to the water.
N/A
P
N/A
No leakage from any part, including any inlet water
hose
N/A
22.48
Appliances connected to the water mains
constructed to prevent backsiphonage of non-potable
water
N/A
22.101
Appliances having provision for attaching a luminaire
incorporate appropriate terminals and internal wiring
(IEC 60335-2-80)
P
23
INTERNAL WIRING
P
23.1
Wireways smooth and free from sharp edges
P
Wires protected against contact with burrs, cooling
fins etc.
P
Wire holes in metal well rounded or provided with
bushings
N/A
No such parts.
Wiring effectively prevented from coming into contact The internal wiring is properly
with moving parts
fixed.
23.2
P
Beads etc. on live wires cannot change their position, No beads.
and are not resting on sharp edges or corners
N/A
Beads inside flexible metal conduits contained within
an insulating sleeve
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 26 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
23.3
Electrical connections and internal conductors
movable relatively to each other not exposed to
undue stress
Flexible metallic tubes not causing damage to
insulation of conductors
Result - Remark
Verdict
N/A
N/A
No such parts.
Open-coil springs not used
N/A
Adequate insulating lining provided inside a coiled
spring, the turns of which touch one another
N/A
No damage after 100 000 flexings for conductors
flexed during normal use and at rated voltage
(IEC 60335-2-80)
N/A
Electric strength test, 1000 V between live parts and
accessible metal parts
N/A
No bare internal wiring.
N/A
23.4
Bare internal wiring sufficiently rigid and fixed
23.5
The insulation of internal wiring withstanding the
electrical stress likely to occur in normal use
N/A
No breakdown when a voltage of 2000 V is applied
for 15 min between the conductor and metal foil
wrapped around the insulation
N/A
23.6
Sleeving used as supplementary insulation on
internal wiring retained in position by positive means
N/A
23.7
The colour combination green/yellow used only for
earthing conductors
Green/yellow is not used in
appliance.
23.8
Aluminium wires not used for internal wiring
No aluminium wire.
P
23.9
No lead-tin soldering of stranded conductors where
they are subject to contact pressure, unless
No soldering for this reason.
P
N/A
clamping means so constructed that there is no risk
of bad contact due to cold flow of the solder
N/A
23.10
The insulation and sheath of internal wiring,
incorporated in external hoses for the connection of
an appliance to the water mains, at least equivalent
to that of light polyvinyl chloride sheathed flexible
cord (60227 IEC 52)
N/A
24
COMPONENTS
P
24.1
Components comply with safety requirements in
relevant IEC standards
P
List of components
TRF No. IEC60335_2_80B_mod
(See appended table)
P
TRF originator: KEMA
www.tuv.com
Page 27 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
N/A
Components not tested and found to comply with
relevant IEC standard for the number of cycles
specified are tested in accordance with 24.1.1 to
24.1.6
P
Components not tested and found to comply with
relevant IEC standard, components not marked or
not used in accordance with its marking, tested under
the conditions occurring in the appliance
24.1.1
24.1.2
24.1.3
24.1.4
Capacitors likely to be permanently subjected to the
supply voltage and used for radio interference
suppression or for voltage dividing, complying with
IEC 60384-14, or
N/A
tested according to annex F
N/A
Safety isolating transformers complying with IEC
61558-2-6, or
tested according to annex G
N/A
Switches complying with IEC 61058-1, the number of
cycles of operation being at least 10 000, or
N/A
tested according to annex H
N/A
If the switch operates a relay or contactor, the
complete switching system is subjected to the test
N/A
Automatic controls complying with IEC 60730-1 with relevant part 2. The number of
cycles of operation being:
N/A
- thermostats:
10 000
N/A
1 000
N/A
300
N/A
- temperature limiters:
- self-resetting thermal cut-outs:
N/A
- voltage maintained non-self-resetting
thermal cut-outs:
1000
30 Approved thermal link.
- other non-self-resetting thermal cut-outs:
- energy regulators:
P
3 000
N/A
10 000
N/A
- timers:
24.1.5
N/A
No transformers.
Thermal motor protectors are tested in combination
with their motor under the conditions specified in
Annex D
N/A
For water valves containing live parts and that are
incorporated in external hoses for connection of an
appliance to the water mains, the degree of
protection declared for subclause 6.5.2 of IEC 607302-8 is IPX7
N/A
Appliance couplers complying with IEC 60320-1
TRF No. IEC60335_2_80B_mod
No appliance coupler.
N/A
TRF originator: KEMA
www.tuv.com
Page 28 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
However, appliances classified higher than IPX0, the
appliance couplers complying with IEC 60320-2-3
N/A
Interconnection couplers complying with IEC 603202-2
N/A
24.1.6
Small lamp holders similar to E10 lampholders
complying with IEC 60238, the requirements for E10
lampholders being applicable
N/A
24.2
Switches or automatic controls in flexible cords are
allowed for appliances not exceeding 25 W
(IEC 60335-2-80)
N/A
No devices causing the protective device in the fixed
wiring to operate in the event of a fault in the
appliance
P
No thermal cut-outs that can be reset by soldering
P
24.3
Switches intended for all-pole disconnection of
stationary appliances are directly connected to the
supply terminals and having a contact separation in
all poles, providing full disconnection under
overvoltage category III conditions
N/A
24.4
Plugs and socket-outlets for extra-low voltage circuits No such appliance or circuit.
and heating elements, not interchangeable with plugs
and socket-outlets listed in IEC 60083 or IEC 609061 or with connectors and appliance inlets complying
with the standard sheets of IEC 60320-1
N/A
24.5
Capacitors in auxiliary windings of motors marked
with their rated voltage and capacitance and used
accordingly
N/A
No auxiliary windings.
Voltage across capacitors in series with a motor
winding does not exceed 1,1 times rated voltage,
when the appliance is supplied at 1,1 times rated
voltage under minimum load
N/A
Working voltage of motors connected to the supply
mains and having basic insulation that is inadequate
for the rated voltage of the appliance, not exceeding
42V
N/A
In addition, the motors are complying with the
requirements of Annex I
N/A
24.7
Hose-sets for connection of appliances to the water
mains, complying with IEC 61770 and supplied with
the appliance
N/A
24.101
Thermal cut-outs in duct fans in order to comply with
cl. 19 are not self-resetting (IEC 60335-2-80)
N/A
24.6
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 29 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
25.1
Appliance not intended for permanent connection to fixed wiring, means for connection
to the supply:
N/A
- supply cord fitted with a plug
N/A
- an appliance inlet having at least the same degree
of protection against moisture as required for the
appliance
N/A
- pins for insertion into socket-outlets
N/A
Appliance not provided with more than one means of
connection to the supply mains
N/A
25.2
Stationary appliance for multiple supply may be
provided with more than one means of connection,
provided electric strength test of 1250 V for 1 min
between each means of connection causes no
breakdown
25.3
25.4
25.5
Result - Remark
500 V
Verdict
P
P
Connection of supply conductors for appliance
intended to be permanently connected to fixed wiring
possible after the appliance has been fixed to its
support
P
Appliance provided with a set of terminals for the
connection of cables or fixed wiring, cross-sectional
areas specified in 26.6
N/A
Appliance provided with a set of terminals allowing
the connection of a flexible cord
N/A
Appliance provided with a set of supply leads
accommodated in a suitable compartment
N/A
Appliance provided with a set of terminals and cable
entries, conduit entries, knock-outs or glands,
allowing connection of appropriate type of cable or
conduit
P
Cable and conduit entries, rated current of appliance
not exceeding 16 A, dimension according to table 10
P
Introduction of conduit or cable does not reduce
clearances or creepage distances below values
specified in 29
P
Method for assemble supply cord with the appliance:
P
- type X attachment
N/A
- type Y attachment
N/A
- type Z attachment is allowed for portable fans
(IEC 60335-2-80)
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 30 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
Type X attachment, other than those with a specially
prepared cord, not used for flat twin tinsel cords
N/A
25.6
Plugs fitted with only one flexible cord
N/A
25.7
Supply cord not lighter than:
N/A
- braided cord (60245 IEC 51)
Not provided.
N/A
- ordinary tough rubber sheathed cord
(60245 IEC 53)
N/A
- ordinary polychloroprene sheathed flexible cord
(60245 IEC 57)
N/A
- flat twin tinsel cord (60227 IEC 41)
N/A
- light polyvinyl chloride sheathed cord
(60227 IEC 52), appliance not exceeding 3 kg
N/A
- ordinary polyvinyl chloride sheathed cord
(60227 IEC 53), appliance exceeding 3 kg
N/A
Temperature rise of external metal parts exceeding
75 K, PVC cord not used, unless
N/A
appliance so constructed that the supply cord is not
likely to touch external metal parts in normal use, or
N/A
the supply cord is appropriate for higher
temperatures, type Y or type Z attachment used
N/A
Nominal cross-sectional area of supply cords
according to table 11; rated current (A); crosssectional area (mm²) ................................................. :
25.9
Supply cord not in contact with sharp points or edges
N/A
25.10
Green/yellow core for earthing purposes in Class I
appliance
N/A
25.11
Conductors of supply cords not consolidated by leadtin soldering where they are subject to contact
pressure, unless
N/A
clamping means so constructed that there is no risk
of bad contacts due to cold flow of the solder
N/A
25.12
Moulding the cord to part of the enclosure does not
damage the insulation of the supply cord
N/A
25.13
Inlet opening so shaped as to prevent damage to the
supply cord
N/A
Unless the enclosure at the inlet opening is of
insulation material, a non-detachable lining or
bushing complying with 29.3 for supplementary
insulation provided
N/A
TRF No. IEC60335_2_80B_mod
Not provided.
N/A
25.8
TRF originator: KEMA
www.tuv.com
Page 31 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
25.14
25.15
Requirement - Test
Result - Remark
If unsheathed supply cord, a similar additional
bushing or lining is required, unless
N/A
the appliance is class 0
N/A
Supply cords adequately protected against excessive
flexing
N/A
Flexing test:
N/A
- applied force (N)...................................................... :
-
N/A
- number of flexings................................................... :
-
N/A
The test does not result in:
N/A
- short circuit between the conductors
N/A
- breakage of more than 10% of the strands of any
conductor
N/A
- separation of the conductor from its terminal
N/A
- loosening of any cord guard
N/A
- damage, within the meaning of the standard, to the
cord or the cord guard
N/A
- broken strands piercing the insulation and
becoming accessible
N/A
Conductors of the supply cord relieved from strain,
twisting and abrasion by use of cord anchorage
Cord anchorage provided.
The cord cannot be pushed into the appliance to
such an extent that the cord or internal parts of the
appliance can be damaged
Pull and torque test of supply cord, values shown in
table 10: pull (N); torque (not on automatic cord reel)
(Nm)........................................................................... :
25.16
Verdict
P
P
30 N; 0.1 Nm
P
Max. 2 mm displacement of the cord, and conductors
not moved more than 1 mm in the terminals
P
Creepage distances and clearances not reduced
below values specified in 29.1
P
Cord anchorages for type X attachments constructed and located so that:
N/A
- replacement of the cord is easily possible
N/A
- it is clear how the relief from strain and the
prevention of twisting are obtained
N/A
- they are suitable for different types of cord
N/A
- cord cannot touch the clamping screws of cord
anchorage if these screws are accessible, unless
separated from accessible metal parts by
supplementary insulation
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 32 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
- the cord is not clamped by a metal screw which
bears directly on the cord
N/A
- at least one part of the cord anchorage securely
fixed to the appliance, unless part of a specially
prepared cord
N/A
- screws which have to be operated when replacing
the cord do not fix any other component, if applicable
N/A
- if labyrinths can be bypassed the test of 25.15 is
nevertheless withstood
N/A
- for Class 0, 0I and I appliances: they are of
insulating material or are provided with an insulating
lining, unless a failure of the insulation of the cord
does not make accessible metal parts live
N/A
- for Class II appliances: they are of insulating
material, or if of metal, they are insulated from
accessible metal parts by supplementary insulation
N/A
25.17
Adequate cord anchorages for type Y and Z
attachment
N/A
25.18
Cord anchorages only accessible with the aid of a
tool, or
N/A
so constructed that the cord can only be fitted with
the aid of a tool
N/A
Type X attachment, glands not used as cord
anchorage in portable appliances
N/A
Tying the cord into a knot or tying the cord with string
not used
N/A
25.20
Conductors of the supply cord for type Y and Z
attachment adequately additionally insulated
N/A
25.21
Space for supply cord for type X attachment or for
connection of fixed wiring constructed to permit
checking of conductors with respect to correct
positioning and connection before fitting any cover,
no risk of damage to the conductors when fitting the
cover, no contact with accessible metal parts if a
conductor becomes loose, etc.
P
For portable appliances, the uninsulated end of a
conductor prevented from any contact with
accessible metal parts, unless the end of the cord is
such that the conductors are unlikely to slip free
N/A
Appliance inlet:
N/A
- live parts not accessible during insertion or removal
N/A
- connector can be inserted without difficulty
N/A
25.19
25.22
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 33 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
25.23
Requirement - Test
Result - Remark
Verdict
- the appliance is not supported by the connector
N/A
- is not for cold conditions if temp. rise of external
metal parts exceeds 75 K, unless the supply cord is
not likely to touch such metal parts
N/A
Interconnection cords comply with the requirements
for the supply cord, except as specified
No interconnection cord.
N/A
If necessary, electric strength test of 16.3
N/A
25.24
Interconnection cords not detachable without the aid
of a tool if compliance with the standard is impaired
when they are disconnected
N/A
25.25
Dimensions of pins compatible with the dimensions
of the relevant socket-outlet. Dimensions of pins and
engagement face in accordance with the relevant
plug in IEC 60083
N/A
26
TERMINALS FOR EXTERNAL CONDUCTORS
26.1
Appliances provided with terminals or equally
effective devices for connection of external
conductors
P
Terminal block provided.
Terminals only accessible after removal of a nondetachable cover
P
N/A
However, earthing terminals may be accessible if a
tool is required to make the connections and means
are provided to clamp the wire independently from its
connection
26.2
Appliances with type X attachment and appliances
for connection to fixed wiring provided with terminals
in which connections are made by means of screws,
nuts or similar devices, unless the connections are
soldered
P
By screw.
P
Screws and nuts serve only to clamp supply
conductors, except
P
internal conductors, if so arranged that they are
unlikely to be displaced when fitting the supply
conductors
P
If soldered connections used, the conductor so
positioned or fixed that reliance is not placed on
soldering alone
Soldering alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free at the soldered joint
TRF No. IEC60335_2_80B_mod
Soldered connection is not
used.
N/A
N/A
TRF originator: KEMA
www.tuv.com
Page 34 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
26.3
Terminals for type X attachment and for connection
to fixed wiring so constructed that the conductor is
clamped between metal surfaces with sufficient
contact pressure and without damaging the
conductor
P
Terminals for type X attachment and those for connection to fixed wiring so fixed that
when tightening or loosening the clamping means:
P
- the terminal does not loosen
P
- internal wiring is not subjected to stress
P
- clearances and creepage distances are not reduced
below the values in 29
P
Compliance checked by inspection and by the test of 0,28
subclause 8.6 of IEC 60999-1, the torque applied
being equal to two-thirds of the torque specified.
Nominal diameter of thread (mm); screw category;
torque (Nm) ............................................................... :
P
26.4
Terminals for type X attachment, except those with a
specially prepared cord, and those for connection to
fixed wiring, no special preparation of conductors
required, and so constructed or placed that
conductors prevented from slipping out
P
26.5
Terminals for type X attachment so located or
shielded that if a wire of a stranded conductor
escapes, no risk of accidental connection to other
parts that result in a hazard
N/A
Stranded conductor test, 8 mm insulation removed
N/A
No contact between live parts and accessible metal
parts and, for class II constructions, between live
parts and metal parts separated from accessible
metal parts by supplementary insulation only
N/A
26.6
Terminals for type X attachment and for connection
to fixed wiring suitable for connection of conductors
with required cross-sectional area according to
table 13; rated current (A); nominal cross-sectional
area (mm²)................................................................. :
Result - Remark
Verdict
Terminal block is suitable for
2
connection up to 2,5mm
rated current < 3A
P
Terminals only suitable for a specially prepared cord
N/A
26.7
Terminals for type X attachment accessible after
removal of a cover or part of the enclosure
N/A
26.8
Terminals for the connection to fixed wiring, including No earthing terminal
the earthing terminal, located close to each other
P
26.9
Terminals of the pillar type constructed and located
as specified
P
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 35 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
26.10
Terminals with screw clamping and screwless
terminals not used for flat twin tinsel cords, unless
conductors ends fitted with a device suitable for
screw terminals
N/A
Pull test of 5 N to the connection
N/A
For type Y and Z attachment: soldered, welded,
crimped and similar connections may be used
N/A
For Class II appliances: the conductor so positioned
or fixed that reliance is not placed on soldering,
welding or crimping alone
N/A
For Class II appliances: soldering, welding or
crimping alone used, barriers provided, clearances
and creepage distances satisfactory if the conductor
becomes free
N/A
27
PROVISION FOR EARTHING
N/A
27.1
Accessible metal parts of Class 0I and I appliances,
permanently and reliably connected to an earthing
terminal or contact of the appliance inlet
N/A
Earthing terminals not connected to neutral terminal
N/A
26.11
Class 0, II and III appliance have no provision for
earthing
27.2
27.3
Result - Remark
Class III
Verdict
P
Safety extra-low voltage circuits not earthed, unless
protective extra-low voltage circuits
N/A
Clamping means adequately secured against
accidental loosening
N/A
Terminals used for the connection of external
equipotential bonding conductors allow connection of
conductors of 2.5 to 6 mm², and
N/A
do not provide earthing continuity between different
parts of the appliance
N/A
Conductors cannot be loosened without the aid of a
tool
N/A
For detachable parts that are plugged into another
part of the appliance, and having an earth
connection, the earth connection made before and
separated after current-carrying connections when
removing the part
N/A
For appliances with supply cord, current-carrying
conductors become taut before earthing conductor, if
the cord slips out of the cord anchorage
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 36 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
27.4
No risk of corrosion resulting from contact between
metal of earthing terminal and other metal
N/A
Adequate resistance to corrosion of coated or
uncoated parts providing earthing continuity, other
than parts of a metal frame or enclosure
N/A
Parts of steel providing earthing continuity provided at
the essential areas with an electroplated coating,
thickness at least 5 µm
N/A
Adequate protection against rusting of parts of
coated or uncoated steel, only intended to provide or
transmit contact pressure
N/A
In case of aluminium alloys precautions taken to
avoid risk of corrosion
N/A
Low resistance of connection between earthing
terminal and earthed metal parts
N/A
This requirement does not apply to connections
providing earthing continuity in the protective extralow voltage circuit, provided that clearances of basic
insulation are based on the rated voltage of the
appliance
N/A
Resistance not exceeding 0,1
resistance test
N/A
27.5
27.6
Result - Remark
Verdict
at the specified low-
The printed conductors of printed circuit boards not
used to provide earthing continuity in hand held
appliances
N/A
They may be used in other appliances if:
N/A
- at least two tracks are used with independent
soldering points and the appliance complies with
requirements of 27.5 for each circuit
N/A
- the material of the printed circuit board complies
with IEC 60249-2-4 or IEC 60249-2-5
N/A
28
SCREWS AND CONNECTIONS
P
28.1
Fixings, electrical connections and connections
providing earthing continuity withstand mechanical
stresses
P
Screws not of soft metal liable to creep, such as zinc
or aluminium
Only metal screws used.
P
Diameter of screws of insulating material min. 3 mm
N/A
Screws of insulating material not used for any
electrical connection or connections providing
earthing continuity
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 37 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
28.3
28.4
29
Verdict
Screws used for electrical connections or
connections providing earthing continuity screw into
metal
P
Screws not of insulating material if their replacement
by a metal screw can impair supplementary or
reinforced insulation
N/A
Type X attachment, screws to be removed for
replacement of supply cord or for user maintenance,
not of insulating material if their replacement by a
metal screw can impair basic insulation
N/A
For screws and nuts; test as specified
28.2
Result - Remark
(See appended table)
P
P
Electrical connections and connections providing
earthing continuity constructed so that contact
pressure not transmitted through insulating material
liable to shrink or distort, unless shrinkage or
distortion compensated
This requirement does not apply to electrical
connections in circuits carrying a current not
exceeding 0.5A
N/A
Space-threaded (sheet metal) screws only used for
electrical connections if they clamp the parts together
N/A
Thread-cutting (self-tapping) screws only used for
electrical connections if they generate a full form
standard machine screw threa
N/A
Such screws not used if they are likely to be operated
by the user or installer unless the thread is formed by
a swaging action
N/A
Thread-cutting and space-threaded screws may be
used in connections providing earthing continuity,
provided unnecessary to disturb the connection and
at least two screws are used for each connection
N/A
Screws and nuts that make mechanical connection
Mechanical connection does
secured against loosening if they also make electrical not serve electrical connection.
connections or connections providing earthing
continuity
N/A
Rivets for electrical connections or connections
providing earthing continuity secured against
loosening if subjected to torsion
N/A
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
P
Clearances, creepage distances and solid insulation
withstand electrical stress
P
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 38 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
29.1
Requirement - Test
Result - Remark
For coatings used on printed circuits boards to
protect the microenvironment (Type A) or to provide
basic insulation (Type B), annex J applies................ :
-
N/A
The microenvironment is pollution degree 1 under
Type A coating
N/A
No creepage distance or clearance requirements
under Type B coating
N/A
Clearances not less than the values specified in table
16, taking into account the rated impulse voltage for
the overvoltage categories of table 15, unless
P
for basic insulation and functional insulation they
comply with the implulse voltage test of clause 14
N/A
However, if the construction is affected by wear,
distortion, movement of the parts or during assembly,
the clearances for rated impulse voltages of 1500V
and above are increased by 0,5 mm and the impulse
voltage test is not applicable
N/A
Impulse voltage test not applicable:
P
- when the microenvironment is pollution degree 3
P
N/A
- for basic insulation of class 0 and class 01
appliances
Appliances are in overvoltage category II
Clearances less than specified in table 16 not
allowed for basic insulation of class 0 and class 0I
appliances,
29.1.1
Verdict
Considered
P
N/A
or if pollution degree 3 is applicable
P
Compliance is checked by inspection and
measurements as specified
P
Clearances of basic insulation withstand the
overvoltages, taking into account the rated impulse
voltage
P
Clearance at the terminals of tubular sheathed
heating elements may be reduced to 1mm if the
microenvironment is pollution degree 1
N/A
Lacquered conductors of windings considered to be
bare conductors
N/A
29.1.2
Clearances of supplementary insulation not less than
those specified for basic insulation in table 16
N/A
29.1.3
Clearances of reinforced insulation not less than
those specified for basic insulation in table 16, but
using the next higher step for rated impulse voltage
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 39 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
29.1.4
For functional insulation, the values of table 16 are
applicable, unless
29.1.5
29.2
29.2.1
Result - Remark
Verdict
P
the appliance complies with clause 19 with the
functional insulation short-circuited
N/A
Lacquered conductors of windings considered to be
bare conductors
N/A
However, clearances at crossover points are not
measured
N/A
Clearance between surfaces of PTC heating
elements may be reduced to 1mm
N/A
Appliances having higher working voltage than rated
voltage, the voltage used for determining clearances
from table 16 is the sum of the rated impulse voltage
and the difference between the peak value of the
working voltage and the peak value of the rated
voltage
N/A
If the secondary winding of a step-down transformer
is earthed, or if there is an earthed screen between
the primary and secondary windings, clearances of
basic insulation on the secondary side not less than
those specified in table 16, but using the next lower
step for rated impulse voltage
N/A
Circuits supplied with a voltage lower than rated
voltage, clearances of functional insulation based on
the working voltage used as the rated voltage in table
15
N/A
Creepage distances not less than those appropriate
for the working voltage, taking into account the
material group and the pollution degree
P
Pollution degree 2 applies, unless
N/A
precautions taken to protect the insulation; pollution
degree 1
N/A
insulation subjected to conductive pollution; pollution
degree 3
P
Microenvironment is pollution degree 3 unless
insulation is enclosed or located that it is unlikely to
be exposed to pollution during normal use
(IEC 60335-2-80)
P
Compliance is checked by inspection and
measurements as specified
P
Creepage distances of basic insulation not less than
specified in table 17
P
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 40 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
For pollution degree 1, creepage distance not less
than the minimum specified for the clearance in table
16, if the clearance has been checked according to
the test of clause 14
N/A
29.2.2
Creepage distances of supplementary insulation at
least as specified for basic insulation in table 17
N/A
29.2.3
Creepage distances of reinforced insulation at least
double as specified for basic insulation in table 17
N/A
29.2.4
Creepage distances of functional insulation not less
than specified in table 18
P
Creepage distances may be reduced if the appliance
complies with clause 19 with the functional insulation
short-circuited
N/A
Supplementary and reinforced insulation having
adequate thickness, or a sufficient number of layers,
to withstand the electrical stresses
N/A
29.3
Compliance checked by:
- measurement, in accordance with 29.3.1, or
29.3.1
29.3.2
29.3.3
30
P
P
- an electric strength test in accordance with 29.3.2,
or
N/A
- an assessment of the thermal quality of the material
combined with an electric strength test, in
accordance with 29.3.3
N/A
Supplementary insulation having a thickness of at
least 1 mm
N/A
Reinforced insulation having a thickness of at least 2
mm
N/A
Each layer of material withstand the electric strength
test of 16.3 for supplementary insulation
N/A
Supplementary insulation consisting of at least 2
layers
N/A
Reinforced insulation consisting of at least 3 layers
N/A
The insulation is subjected to the dry heat test Bb of
IEC 60068-2-2, followed by
N/A
the electric strength test of 16.3
N/A
If the temperature rise during the tests of Clause 19
does not exceed the value specified in Table 3, the
test of IEC 60068-2-2 is not carried out
N/A
RESISTANCE TO HEAT AND FIRE
TRF No. IEC60335_2_80B_mod
P
TRF originator: KEMA
www.tuv.com
Page 41 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
30.1
External parts of non-metallic material,
P
parts supporting live parts, and
P
thermoplastic material providing supplementary or
reinforced insulation,
N/A
sufficiently resistant to heat
P
Ball-pressure test according to IEC 60695-10-2
P
External parts: at 40 °C plus the maximum
Enclosure tested on 75°C
temperature rise determined during the test of clause
11, or at 75 °C, whichever is the higher; temperature
(°C)............................................................................. :
P
Parts supporting live parts: at 40°C plus the
maximum temperature rise determined during the
test of clause 11, or at 125°C, whichever is the
higher; temperature (°C)............................................ :
Approved terminal block
Parts of thermoplastic material providing
supplementary or reinforced insulation, 25°C plus the
maximum temperature rise determined during clause
19, if higher; temperature (°C)................................... :
30.2
Relevant parts of non-metallic material adequately
resistant to ignition and spread of fire
30.2.1
Glow-wire test of IEC 60695-2-11 at 550 °C, unless
30.2.3
30.2.3.1
30.2.3.2
P
N/A
P
Enclosure.
P
the material is classified at least HB40 according to
IEC 60695-11-10
N/A
Parts for which the glow-wire test cannot be carried
out meet the requirements in ISO9772 for category
HBF material
N/A
Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2
P
Test not applicable to conditions as specified
P
Parts of insulating material supporting connections
carrying a current exceeding 0.2A during normal
operation, and
P
parts of insulating material within a distance of 3mm,
N/A
having a glow-wire flammability index of at least
850°C according to IEC 60695-2-12
N/A
Parts of insulating material supporting currentcarrying connections, and
P
N/A
parts of insulating material within a distance of 3mm,
subjected to glow-wire test of IEC 60695-2-11
TRF No. IEC60335_2_80B_mod
Approved terminal block
P
TRF originator: KEMA
www.tuv.com
Page 42 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
N/A
Test not carried out on material having a glow-wire
ignition temperature according to IEC 60695-2-13 as
specified
Glow-wire test of IEC 60695-2-11, the temperature being:
P
N/A
-775°C, for connections carrying a current exceeding
0,2A during normal operation
-650°C, for other connections
30.2.4
31
32
A
B
Approved components
P
Parts that during the test produce a flame persisting
longer than 2 s, tested as specified
N/A
If a flame persists longer than 2 s during the test,
parts above the connection, as specified, subjected
to the needle-flame test of annex E, unless
N/A
the material is classified as V-0 or V-1 according to
IEC 60695-11-10
N/A
Base material of printed circuit boards subjected to
needle-flame test of annex E
N/A
Test not applicable to conditions as specified
N/A
RESISTANCE TO RUSTING
P
Relevant ferrous parts adequately protected against
rusting
P
RADIATION, TOXICITY AND SIMILAR HAZARDS
P
Appliance does not emit harmful radiation
P
Appliance does not present a toxic or similar hazard
N/A
ANNEX A (INFORMATIVE)
ROUTINE TESTS
N/A
Description of routine tests to be carried out by the
manufacturer
N/A
ANNEX B (NORMATIVE)
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
N/A
The following modifications to this standard are
applicable for appliances powered by batteries that
are recharged in the appliance
N/A
This annex does not apply to battery chargers
TRF No. IEC60335_2_80B_mod
No batteries.
N/A
TRF originator: KEMA
www.tuv.com
Page 43 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
3.1.9
Appliance operated under the following conditions:
N/A
-the appliance, supplied by its fully charged battery,
operated as specified in relevant part 2
N/A
-the battery is charged, the battery being initially
discharged to such an extent that the appliance
cannot operate
N/A
-if possible, the appliance is supplied from the supply
mains through its battery charger, the battery being
initially discharged to such an extent that the
appliance cannot operate. The appliance is operated
as specified in relevant part 2
N/A
If the appliance incorporates inductive coupling
between two parts that are detachable from each
other, the appliance is supplied from the supply
mains with the detachable part removed
N/A
3.6.2
Part to be removed in order to discard the battery is
not considered to be detachable
N/A
5.101
Appliances supplied from the supply mains tested as
specified for motor-operated appliances
N/A
7.1
Battery compartment for batteries intended to be
replaced by the user, marked with battery voltage
and polarity of the terminals
N/A
7.12
The instructions for appliances incorporating
batteries intended to be replaced by the user includes
required information
N/A
Details about how to remove batteries containing
materials hazardous to the environment given
N/A
7.15
Markings placed on the part of the appliance
connected to the supply mains
N/A
8.2
Appliances having batteries that according to the
instruction may be replaced by the user need only
have basic insulation between live parts and the inner
surface of the battery compartment
N/A
If the appliance can be operated without batteries,
double or reinforced insulation required
N/A
11.7
The battery is charged for the period described
N/A
19.1
Appliances subjected to tests of 19.101, 19.102 and
19.103
N/A
19.101
Appliances supplied at rated voltage for 168 h, the
battery being continually charged
N/A
19.102
Short-circuiting of the terminals of the battery, being
fully charged, for appliances having batteries that can
be removed without the aid of a tool
N/A
TRF No. IEC60335_2_80B_mod
Result - Remark
Verdict
TRF originator: KEMA
www.tuv.com
Page 44 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
19.103
Appliances having batteries replaceable by the user
supplied at rated voltage under normal operation with
the battery removed or in any position allowed by the
construction
N/A
21.101
Appliances having pins for insertion into socketoutlets have adequate mechanical strength, checked
according to procedure 2 of IEC 68-2-32
N/A
Part of the appliance incorporating the pins subjected to the free fall test, procedure 2,
of IEC 60068-2-32, the number of falls being:
N/A
- 100, the mass of part does not exceed 250 g
N/A
- 50, the mass of part exceeds 250 g
N/A
After the test, the requirements of 8.1, 15.1.1, 16.3
and clause 29 are met
N/A
22.3
Appliances having pins for insertion into socketoutlets tested as fully assembled as possible
N/A
25.13
An additional lining or bushing not required for
interconnection cords operating at safety extra-low
voltage
N/A
30.2
For parts of the appliance connected to the supply
mains during the charging period, 30.2.3 applies
N/A
For other parts, 30.2.2 applies
N/A
ANNEX C (NORMATIVE)
AGEING TEST ON MOTORS
N/A
Tests, as described, carried out when doubt with
regard to the temperature classification of the
insulation of a motor winding
N/A
ANNEX D (NORMATIVE)
THERMAL MOTOR PROTECTORS
N/A
Applicable to appliances having motors that
incorporate thermal motor protectors
N/A
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST
N/A
Needle-flame test carried out in accordance with
IEC 60695-2-2, with the following modifications:
N/A
Severities
N/A
The duration of application of the test flame is
30 s ± 1 s
N/A
C
D
E
5
TRF No. IEC60335_2_80B_mod
Result - Remark
Verdict
TRF originator: KEMA
www.tuv.com
Page 45 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
8
Test procedure
N/A
8.2
The specimen so arranged that the flame can be
applied to a vertical or horizontal edge as shown in
the examples of figure 1
N/A
8.4
The first paragraph does not apply
N/A
If possible, the flame is applied at least 10 mm from a
corner
N/A
The test is carried out on one specimen
N/A
If the specimen does not withstand the test, the test
may be repeated on two further specimens, both
withstanding the test
N/A
Evaluation of test results
N/A
The duration of burning not exceeding 30 s
N/A
However, for printed circuit boards, the duration of
burning not exceeding 15 s
N/A
ANNEX F (NORMATIVE)
CAPACITORS
N/A
Capacitors likely to be permanently subjected to the
supply voltage, and used for radio interference
suppression or voltage dividing, comply with the
following clauses of IEC 60384-14, with the following
modifications:
N/A
1.5
Terminology
N/A
1.5.3
Class X capacitors tested according to subclass X2
N/A
1.5.4
This subclause is applicable
N/A
1.6
Marking
N/A
Items a) and b) are applicable
N/A
3.4
Approval testing
N/A
3.4.3.2
Table II is applicable as described
N/A
4.1
Visual examination and check of dimensions
N/A
This subclause is applicable
N/A
4.2
Electrical tests
N/A
4.2.1
This subclause is applicable
N/A
4.2.5
This subclause is applicable
N/A
4.2.5.2
Only table IX is applicable
N/A
Values for test A apply
N/A
8.5
10
F
TRF No. IEC60335_2_80B_mod
Result - Remark
Verdict
TRF originator: KEMA
www.tuv.com
Page 46 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
4.12
4.13
4.14
4.14.7
4.17
4.18
G
Requirement - Test
Result - Remark
Verdict
However, for capacitors in heating appliances the
values for test B or C apply
N/A
Damp heat, steady state
N/A
This subclause is applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
Impulse voltage
N/A
This subclause is applicable
N/A
Endurance
N/A
Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7
applicable
N/A
Only insulation resistance and voltage proof are
checked
N/A
Visual examination, no visible damage
N/A
Passive flammability test
N/A
This subclause is applicable
N/A
Active flammability test
N/A
This subclause is applicable
N/A
ANNEX G (NORMATIVE)
SAFETY ISOLATING TRANSFORMERS
N/A
The following modifications to this standard are
applicable for safety isolating transformers:
No transformers.
N/A
7
Marking and instructions
N/A
7.1
Transformers for specific use marked with:
N/A
-name, trademark or identification mark of the
manufacturer or responsible vendor
N/A
-model or type reference
N/A
Overload protection of transformers and associated circuits
N/A
Fail-safe transformers comply with subclause 15.5 of
IEC 61558-1
N/A
Construction
N/A
Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are
applicable
N/A
29
Clearances, creepage distances and solid insulation
N/A
29.1, 29.2
and 29.3
The distances specified in items 2a, 2c and 3 in table
13 of IEC 61558-1 apply
N/A
17
22
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 47 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
H
ANNEX H (NORMATIVE)
SWITCHES
N/A
Switches comply with the following clauses of IEC 61058-1, as modified:
N/A
-The tests of IEC 61058-1 carried out under the
conditions occurring in the appliance
N/A
-Before being tested, switches are operated 20 times
without load
N/A
Marking and documentation
N/A
Switches are not required to be marked
N/A
However, switches that can be tested separately
from the appliance marked with the manufacturer’s
name or trade mark and the type reference
N/A
Mechanism
N/A
The tests may be carried out on a separate sample
N/A
15
Insulation resistance and dielectric strength
N/A
15.1
Not applicable
N/A
15.2
Not applicable
N/A
15.3
Applicable for full disconnection and microdisconnection
N/A
17
Endurance
N/A
Compliance is checked on three separate appliances
or switches
N/A
For 17.2.4.4, the number of cycles is 10 000, unless
otherwise specified in 24.1.3 of the relevant part 2 of
IEC 60335
N/A
Switches for operation under no load and which can
be operated only by a tool and switches operated by
hand that are interlocked so that they cannot be
operated under load, are not subjected to the tests
N/A
Subclauses 17.2.2 and 17.2.5.2 not applicable
N/A
The ambient temperature during the test is that
occurring in the appliance during the test of Clause
11 in IEC 60335-1
N/A
Temperature rise of the terminals not more than 30 K
above the temperature rise measured in clause 11 of
IEC 60335-1
N/A
Clearances, creepage distances, solid insulation and coatings of rigid printed board
assemblies
N/A
8
13
20
TRF No. IEC60335_2_80B_mod
Result - Remark
Verdict
TRF originator: KEMA
www.tuv.com
Page 48 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
This clause is applicable to clearances and creepage
distances for functional insulation, across full
disconnection and micro-disconnection, as stated in
table 24
N/A
ANNEX I (NORMATIVE)
MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE RATED
VOLTAGE OF THE APPLIANCE
N/A
The following modifications to this standard are
applicable for motors having basic insulation that is
inadequate for the rated voltage of the appliance:
N/A
8
Protection against access to live parts
N/A
8.1
Metal parts of the motor are considered to be bare
live parts
N/A
11
Heating
N/A
11.3
Temperature rise of the body of the motor is
determined instead of the temperature rise of the
windings
N/A
11.8
Temperature rise of the body of the motor, where in
contact with insulating material, not exceeding values
in table 3 for the relevant insulating material
N/A
16
Leakage current and electric strength
N/A
16.3
Insulation between live parts of the motor and its
other metal parts not subjected to the test
N/A
19
Abnormal operation
N/A
19.1
The tests of 19.7 to 19.9 not carried out
N/A
19.101
Appliance operated at rated voltage with each of the following fault conditions:
N/A
- short circuit of the terminals of the motor, including
any capacitor incorporated in the motor circuit
N/A
- short circuit of each diode of the rectifier
N/A
- open circuit of the supply to the motor
N/A
- open circuit of any parallel resistor, the motor being
in operation
N/A
Only one fault simulated at a time, the tests carried
out consecutively
N/A
22
Construction
N/A
22.101
For class I appliances incorporating a motor supplied
by a rectifier circuit, the d.c. circuit being insulated
from accessible parts of the appliance by double or
reinforced insulation
N/A
I
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 49 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
J
6.6
6.6.1
6.6.3
6.8.6
6.9
K
Requirement - Test
Result - Remark
Verdict
Compliance checked by the tests specified for double
and reinforced insulation
N/A
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
N/A
Testing of protective coatings of printed circuit boards No coated PCB.
carried out in accordance with IEC 60664-3 with the
following modifications:
N/A
Climatic sequence
N/A
When production samples are used, three samples
of the printed circuit board are tested
N/A
Cold
N/A
The test is carried out at -25°C
N/A
Rapid change of temperature
N/A
Severity 1 is specified
N/A
Partial discharge extinction voltage
N/A
Type A coatings not subjected to a partial discharge
test
N/A
Additional tests
N/A
This subclause is not applicable
N/A
ANNEX K (NORMATIVE)
OVERVOLTAGE CATEGORIES
P
The information on overvoltage categories is
extracted from IEC 60664-1
P
Overvoltage category is a numeral defining a
transient overvoltage condition
P
Equipment of overvoltage category IV is for use at
the origin of the installation
N/A
Equipment of overvoltage category III is equipment in
fixed installations and for cases where the reliability
and the availability of the equipment is subject to
special requirements
N/A
Equipment of overvoltage category II is energy
consuming equipment to be supplied from the fixed
installation
If such equipment is subjected to special
requirements with regard to reliability and availability,
overvoltage category III applies
TRF No. IEC60335_2_80B_mod
According to the clause 29.1.
P
N/A
TRF originator: KEMA
www.tuv.com
Page 50 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
N/A
Equipment of overvoltage category I is equipment for
connection to circuits in which measures are taken to
limit transient overvoltages to an appropriate low level
L
M
ANNEX L (INFORMATIVE)
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
P
Sequences for the determination of clearances and
creepage distances
P
ANNEX M (NORMATIVE)
POLLUTION DEGREE
P
The information on pollution degrees is extracted
from IEC 60664-1
P
Pollution
P
The microenvironment determines the effect of
pollution on the insulation, taking into account the
microenvironment
P
Means may be provided to reduce pollution at the
insulation by effective enclosures or similar
P
Minimum clearances specified where pollution may
be present in the microenvironment
P
Degrees of pollution in the microenvironment
P
For evaluating creepage distances, the following degrees of pollution in the
microenvironment are established:
P
- pollution degree 1: no pollution or only dry, nonconductive pollution occurs. The pollution has no
influence
N/A
- pollution degree 2: only non-conductive pollution
occurs, except that occasionally a temporary
conductivity caused by condensation is to be
expected
N/A
- pollution degree 3: conductive pollution occurs or
dry non-conductive pollution occurs that becomes
conductive due to condensation that is to be
expected
N
According clause 29.2 of
IEC 60335-2-80
P
- pollution degree 4: the pollution generates
persistent conductivity caused by conductive dust or
by rain or snow
N/A
ANNEX N (NORMATIVE)
PROOF TRACKING TEST
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 51 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
The proof tracking test is carried out in accordance
with IEC 60112 with the following modifications:
N/A
7
Test apparatus
N/A
7.3
Test solutions
N/A
Test solution A is used
N/A
10
Determination of proof tracking index (PTI)
N/A
10.1
Procedure
N/A
The proof voltage is 100V, 175V, 400V or 600V ...... :
N/A
The last paragraph of Clause 3 applies
N/A
The test is carried out on five specimens
N/A
In case of doubt, additional test with proof voltage
reduced by 25V, the number of drops increased to
100
N/A
Report
N/A
The report stating if the PTI value was based on a
test using 100 drops with a test voltage of (PTI-25) V
N/A
10.2
O
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
P
Description of tests for determination of resistance to
heat and fire
P
ANNEX P (INFORMATIVE)
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
N/A
Modifications applicable for class 0 and 01 appliances having a rated voltage
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE
N/A
Modifications may also be applied to class 1 appliances having a rated voltage
exceeding 150V, intended to be used in countries having a warm damp equable
climate and that are marked WDaE, if liable to be connected to a supply mains that
excludes the protective earthing conductor
N/A
5
General conditions for the tests
N/A
5.7
The ambient temperature for the tests of Clauses 11
+3
and 13 is 40 /0
N/A
7
Marking and instructions
N/A
7.1
The appliance marked with the letters WDaE
N/A
P
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 52 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
7.12
The instructions state that the appliance is to be
supplied through a RCD having a rated residual
operating current not exceeding 30 mA
N/A
The instructions state that the appliance is
considered to be suitable for use in countries having
a warm damp equable climate, but may also be used
in other countries
N/A
11
Heating
N/A
11.8
The values of Table 3 are reduced by 15 K
N/A
13
Leakage current and electric strength at operating temperature
N/A
13.2
The leakage current for class I appliances not
exceeding 0,5 mA
N/A
15
Moisture resistance
N/A
15.3
The value of t is 37 °C
N/A
16
Leakage current and electric strength
N/A
16.2
The leakage current for class I appliances not
exceeding 0,5 mA
N/A
19
Abnormal operation
N/A
19.13
The leakage current test of 16.2 is applied in addition
to the electric strength test of 16.3
N/A
Q
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
N/A
Description of tests for appliances incorporating electronic circuits
N/A
ANNEX R (NORMATIVE)
SOFTWARE EVALUATION
N/A
Software evaluated in accordance with the following clauses of Annex H of IEC 607301, as modified
N/A
Definitions
N/A
Only definitions H.2.16 to H.2.20 applicable
N/A
Information
N/A
Only footnotes 12) to 18) of Table 7.2, as modified,
applicable
N/A
Controls using software
N/A
All the subclauses of H.11.12, as modified, except
H.11.12.6 and H.11.12.6.1, applicable
N/A
Delete text
N/A
R
H.2
H.7
H.11.12
H.11.12.7
TRF No. IEC60335_2_80B_mod
Result - Remark
Verdict
TRF originator: KEMA
www.tuv.com
Page 53 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
H.11.12.7.1 For appliances using software class C having a
single channel with self-test and monitoring structure,
the manufacturer provides the measures necessary
to address the fault/errors in safety related segments
and data
N/A
H.11.12.8
N/A
Software fault/error detection occurs before
compliance with 19.13 of IEC 60335-1 is impaired
H.11.12.8.1 Replace text
N/A
H.11.12.13 Software and safety related hardware under its
control initializes and terminates before compliance
with 19.13 of IEC 60335-1 is impaired
N/A
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 54 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
Verdict
EU differences
6
CLASSIFICATION
P
6.1
Protection against electric shock:
Class I, II, III .............................................................:
7
MARKING AND INSTRUCTIONS
7.1
Rated voltage or voltage range (V) ..........................:
12 V
P
Single-phase appliances: 230 V covered
Covered, see previous line.
P
III
P
P
Multi-phase appliances: 400 V covered
N/A
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
N/A
25.6
Plugs fitted with only one flexible cord
N/A
25.7
No power supply cord provided.
Supply cords of single-phase portable appliances
having a rated current not exceeding 16 A shall be
fitted with a plug complying with the following
standard sheets of IEC 60083:1975:
N/A
- for Class I appliances: Standard Sheet C2b, C3B or
C4;
N/A
- for Class II appliances: Standard Sheet C5 or C6
N/A
Supply cord not lighter than:
N/A
- ordinary polychloroprene sheathed flexible cord
(code designation 60245 IEC 57)
N/A
When supply cords having high flexibility are used,
they shall not be lighter than
N/A
- rubber insulated and sheathed cord (code
designation 60245 IEC 86);
N/A
- rubber insulated, crosslinked PVC sheathed cord
(code designation 60245 IEC 87);
N/A
- crosslinked PVC insulated and sheathed cord (code
designation 60245 IEC 88).
N/A
ANNEX EMF
The Tested product also complies to the requirements of IEC 62233:2005

Limit ……………100%
P
TRF No. IEC60335_2_80B_mod
Measured max. : 0,628 %
TRF originator: KEMA
www.tuv.com
Page 55 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
10.1
TABLE: Power input deviation
Verdict
P
Input deviation of/at:
P rated (W)
P measured
(W)
dP
Required dP
VENTS 100 Xstar 12
15
14,5
- 0,5 W
+ 0,3 W
10.2
Remark
TABLE: Current deviation
Current deviation of/at:
I rated (A)
N/A
I measured (A)
dI
Required dI
Remark
-
11.8
TABLE: Heating test, thermocouples
P
Test voltage (V) ........................................................: 12,7

Ambient (°C).............................................................: 45

Thermocouple locations
∆T (K)
Max. ∆T (K)
Terminal block
3
40
Supply cord of the motor
10
30
Enclosure
3
according to clause 30.1
Plastic held in place the motor (the same
material as the enclosure)
5
according to clause 30.1
For model: VENTS 100 Xstar 12
Note(s):
With a rated maximum ambient temperature of 45°C, the max. temperature rise is calculated as follows:
Winding components:
- Class 130 (resistance method)
→ ∆Tmax = 95 - (45-25) K = 75 K
Surface of components:
- Terminal block
→ ∆Tmax = 60 - (45-25) K = 40 K
- Internal wire
→ ∆Tmax = 50 - (45-25) K = 30 K
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 56 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
11.8
TABLE: Heating test, resistance method
P
Test voltage (V) ........................................................: 12,7

Ambient, t1 (°C) .........................................................: 45

Ambient, t2 (°C) .........................................................: 45

Temperature rise of winding
VENTS 100 Xstar 12
13.2
Verdict
R1 ( )
R2 ( )
dT (K)
Max. dT (K)
Insulation
class
2,68
3,13
48
75
130
TABLE: Leakage current
P
Heating appliances: 1.15 x rated input ..................:
-
Motor-operated and combined appliances:
1.06 x rated voltage................................................:
12,7

Leakage current between

I (mA)
Max. allowed I (mA)
0.01
0.5
For model VENTS 100 Xstar 12
Conductor and enclosure wrapped with foil
13.3
TABLE: Electric strength
P
Test voltage applied between:
Voltage (V)
Breakdown
(Yes/No)
500
No
For model VENTS 100 Xstar 12
Conductor and enclosure wrapped with foil
14
TABLE: Transient overvoltages
Clearance between:
Cl (mm)
N
Required
Cl (mm)
Rated impulse
voltage (V)
Impulse test
voltage (V)
Flashover
(Yes/No)
16.2
TABLE: Leakage current
P
Single phase appliances: 1.06 x rated voltage ......:
12,7

Three phase appliances 1.06 x rated voltage
divided by √3: .........................................................:
-

Leakage current between
I (mA)
Max. allowed I (mA)
0.01
0.5
For model VENTS 100 Xstar 12
Conductor and enclosure wrapped with foil
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 57 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
16.3
TABLE: Electric strength
Result - Remark
Verdict
P
Test voltage applied between:
Voltage (V)
Breakdown
(Yes/No)
500
No
For model VENTS 100 Xstar 12
Conductor and enclosure wrapped with foil
17
TABLE: Overload protection, temperature rise
N/A
Temperature rise of part/at:
dT (K)
Max. dT (K)
19.7
TABLE: Abnormal operation, locked rotor/moving parts
P
Test voltage (V) ........................................................: 12

Ambient, t1 (°C) .........................................................: 25

Ambient, t2 (°C) .........................................................: 25

Temperature of winding
Thermal link operated
19.9
R1 ( )
R2 ( )
dT (K)
T (°C)
-
-
-
-
Max. T (°C)
TABLE: Abnormal operation, running overload
N/A
Test voltage (V) ........................................................:
-

Ambient, t1 (°C) .........................................................:
-

Ambient, t2 (°C) .........................................................:
-

Temperature of winding
R1 ( )
R2 ( )
dT (K)
T (°C)
Max. T (°C)
-
19.13
TABLE: Abnormal operation, temperature rises
Thermocouple locations
VENTS 100 Xstar 12
P
dT (K)
Max. dT (K)
Enclosure
2
according to clause 30.1
Plastic held in place the motor (the
same material as the enclosure)
4
according to clause 30.1
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 58 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
24.1
TABLE: Components
Verdict
P
Object / part No. Manufacturer/
trademark
Type / model
Technical data
Terminal
LTA 12-2,5
380V; 2,5 mm
Simet
Standard
Mark(s) of
conformity
2
EN 60998-2-1
BBJ*
2
Alt. terminal
Heavy Power
PA8H+P
380V; 2,5 mm
EN 60998-2-1
VDE*
Motor
HUNAN KELI
BL 58-12 E01
AC 230V, 50Hz, B
IEC 60335-1
IEC 60335-2-80
Tested in the
equipment
Thermal link
Aupo Electronics Ltd. P7
AC 250V, 2A 150ºC
EN 60691
VDE*
LED Cup lamp
and lamphorder
Ningbo Zhenkang
Electron Technology
Co., LTD.
AC 12 V
IEC 60335-1
IEC 60335-2-80
Tested in the
equipment
*)
MR16
An asterisk indicates a mark which assures the agreed level of surveillance
28.1
TABLE: Threaded part torque test
Threaded part identification
Diameter of thread
(mm)
Column number
(I, II, or III)
Applied torque
(Nm)
3.8
II
1.2
Motor holder screw
29.1
P
TABLE: Clearances
P
Overvoltage category...... :
II
P
Type of insulation:
Rated impulse
voltage (V):
Min. cl
(mm)
Basic
Functional
Supplementary
Reinforced
Verdict / Remark
N/A
330
0,5
500
0,5
800
0,5
N/A
1 500
1,0
N/A
2 500
2,0
N/A
4 000
3,5
N/A
6 000
6,0
N/A
8 000
8,5
N/A
10 000
11,5
N/A
2
TRF No. IEC60335_2_80B_mod
P
TRF originator: KEMA
www.tuv.com
Page 59 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
29.2
TABLE: Creepage distances, basic, supplementary and reinforced insulation
Working voltage
(V)
Verdict
P
Creepage distance
(mm)
Pollution degree
1
2
3
Material group
Material group
I
II
IIIa/IIIb
I
II
Type of insulation
IIIa/IIIb
B*)
S*)
R*)
Verdict


P

N/A
≤50
0,2
0,6
0,9
1,2
1,5
1,7
1,9
2
≤50
0,2
0,6
0,9
1,2
1,5
1,7
1,9

≤50
0,4
1,2
1,8
2,4
3,0
3,4
3,8

>50 and ≤125
0,3
0,8
1,1
1,5
1,9
2,1
2,4
>50 and ≤125
0,3
0,8
1,1
1,5
1,9
2,1
2,4

>50 and ≤125
0,6
1,6
2,2
3,0
3,8
4,2
4,8


>125 and ≤250
0,6
1,3
1,8
2,5
3,2
3,6
4,0
9


N/A
>125 and ≤250
0,6
1,3
1,8
2,5
3,2
3,6
4,0

9

N/A
>125 and ≤250
1,2
2,6
3,6
5,0
6,4
7,2
8,0


12
N/A
>250 and ≤400
1,0
2,0
2,8
4,0
5,0
5,6
6,3


N/A
>250 and ≤400
1,0
2,0
2,8
4,0
5,0
5,6
6,3


N/A
>250 and ≤400
2,0
4,0
5,6
8,0
10,0
11,2
12,6

>400 and ≤500
1,3
2,5
3,6
5,0
6,3
7,1
8,0
>400 and ≤500
1,3
2,5
3,6
5,0
6,3
7,1
8,0

>400 and ≤500
2,6
5,0
7,2
10,0
12,6
14,2
16,0

>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0

>500 and ≤800
3,6
6,4
9,0
12,6
16,0
18,0
20,0

>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5

>800 and ≤1000
4,8
8,0
11,2
16,0
20,0
22,0
25,0

>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0

>1000 and ≤1250
6,4
10,0
14,2
20,0
25,0
28,0
32,0

>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
TRF No. IEC60335_2_80B_mod
N/A



N/A

N/A
N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A
TRF originator: KEMA
www.tuv.com
Page 60 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0

>1250 and ≤1600
8,4
12,6
18,0
25,0
32,0
36,0
40,0

>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0

>1600 and ≤2000
11,2
16,0
22,0
32,0
40,0
44,0
50,0

>2000 and ≤2500
7,5
10,0
14,0
20,0
25, 0
28,0
32,0
>2000 and ≤2500
7,5
10,0
14,0
20,0
25, 0
28,0
32,0

>2000 and ≤2500
15,0
20,0
28,0
40,0
50,0
56,0
64,0

>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0

>2500 and ≤3200
20,0
25,0
36,0
50,0
64,0
72,0
80,0

>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0

>3200 and ≤4000
25,0
32,0
44,0
64,0
80,0
90,0
100,0

>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0

>4000 and ≤5000
32,0
40,0
56,0
80,0
100,0 112,0
126,0

>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0

>5000 and ≤6300
40,0
50,0
72,0
100,0
126,0 142,0
160,0

>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0

>6300 and ≤8000
50,0
64,0
90,0
126,0
160,0 180,0
200,0

>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0
>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0

>8000 and ≤10000
64,0
80,0
112,0
160,0
200,0 220,0
250,0

>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0
>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0

>10000 and ≤12500 80,0
100,0
142,0
200,0
250,0 280,0
320,0

Verdict

N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A
N/A



N/A

N/A

N/A
N/A
*), B=Basic, S=Supplementary and R=Reinforced
TRF No. IEC60335_2_80B_mod
TRF originator: KEMA
www.tuv.com
Page 61 of 64
Report No.: 28207876 001
IEC 60335-2-80
Clause
Requirement - Test
Result - Remark
29.2
TABLE: Creepage distances, functional insulation
Working voltage
(V)
Verdict
P
Creepage distance
(mm)
Pollution degree
1
2
3
Material group
Material group
I
II
IIIa/IIIb
I
II
IIIa/IIIb
Verdict / Remark
≤50
0,2
0,6
0,8
1,1
1,4
1,6
1,8
P
>50 and ≤125
0,3
0,7
1,0
1,4
1,8
2,0
2,2
N/A
>125 and ≤250
0,4
1,0
1,4
2,0
2,5
2,8
3,2
N/A
>250 and ≤400
0,8
1,6
2,2
3,2
4,0
4,5
5,0
N/A
>400 and ≤500
1,0
2,0
2,8
4,0
5,0
5,6
6,3
N/A
>500 and ≤800
1,8
3,2
4,5
6,3
8,0
9,0
10,0
N/A
>800 and ≤1000
2,4
4,0
5,6
8,0
10,0
11,0
12,5
N/A
>1000 and ≤1250
3,2
5,0
7,1
10,0
12,5
14,0
16,0
N/A
>1250 and ≤1600
4,2
6,3
9,0
12,5
16,0
18,0
20,0
N/A
>1600 and ≤2000
5,6
8,0
11,0
16,0
20,0
22,0
25,0
N/A
>2000 and ≤2500
7,5
10,0
14,0
20,0
25,0
28,0
32,0
N/A
>2500 and ≤3200
10,0
12,5
18,0
25,0
32,0
36,0
40,0
N/A
>3200 and ≤4000
12,5
16,0
22,0
32,0
40,0
45,0
50,0
N/A
>4000 and ≤5000
16,0
20,0
28,0
40,0
50,0
56,0
63,0
N/A
>5000 and ≤6300
20,0
25,0
36,0
50,0
63,0
71,0
80,0
N/A
>6300 and ≤8000
25,0
32,0
45,0
63,0
80,0
90,0
100,0
N/A
>8000 and ≤10000
32,0
40,0
56,0
80,0
100,0 110,0
125,0
N/A
>10000 and ≤12500 40,0
50,0
71,0
100,0
125,0 140,0
160,0
N/A
30.1
TABLE: Ball pressure
Part
Enclosure
TRF No. IEC60335_2_80B_mod
P
Test temperature (°C)
Impression diameter
(mm)
Allowed impression
diameter (mm)
75
0.8
2
TRF originator: KEMA
www.tuv.com
Page 62 of 64
Pictures of the appliances
Xstar
Report No.: 28207876 001
www.tuv.com
Page 63 of 64
Pictures of the appliances
Xstar
Report No.: 28207876 001
www.tuv.com
Page 64 of 64
Pictures of the appliances
-
Report No.: 28207876 001
www.tuv.com
Page 1 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
5
GENERAL CONDITIONS FOR THE TESTS
Tests performed according to cl. 5, e.g. nature of
supply, sequence of testing, etc. The test of 19.14 is
carried out before the tests of 19.11.
Result - Remark
Verdict
P
7
MARKING AND INSTRUCTIONS
7.5
The power input is related to the arithmetic mean
value of the rated voltage range
N/A
7.6
Correct symbols used
N/A
7.12
Instructions for safe use provided
P
The instructions state that:
- the appliance is not to be used by children or
persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction
P
8
PROTECTION AGAINST ACCESS TO LIVE PARTS
8.1.1
“Without appreciable force” is considered to be a
force not exceeding 1N (Note 2)
N/A
8.1.2
“Without appreciable force” is considered to be a
force not exceeding 1N (Note 2)
N/A
8.1.3
“Without appreciable force” is considered to be a
force not exceeding 1N (Note1)
N/A
8.1.4
- for peak values over 15kV, the energy in the
discharge not exceeding 350 mJ
N/A
8.2
Note 1 does not apply
N/A
Note: Built-in appliances and fixed appliances are
tested after installation.
N/A
10
POWER INPUT AND CURRENT
10.1
The permissible deviations apply for both limits of
the range for appliances marked with a rated
voltage range having limits differing by more than
10 % of the arithmetic mean value of the range.
N/A
Note 1 and 2 do not apply
N/A
The permissible deviations apply for both limits of
the range for appliances marked with a rated
voltage range having limits differing by more than
10 % of the arithmetic mean value of the range.
N/A
Test for an appliance with one or more rated voltage
ranges
N/A
10.2
www.tuv.com
Page 2 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
11
HEATING
14
Result - Remark
Verdict
Table 3:
First entry:
Replace the terms “class A, class B, class F and
class H” by the terms “class 105, class 120, class
130, class 155 and class 180”
P
Table 3:
Fifth entry:
Rubber, polychloroprene or polyvinyl chloride
insulation of internal and external wiring, including
supply cords:
without temperature rating or with a temperature
rating not exceeding 75 °C
with temperature rating (T) where T exceeds 75 °C
P
Footnote:
The temperature rise limit of windings in transformers
and inductors mounted on printed circuit boards is
equal to the thermal class of the winding insulation
reduced by 25 K provided the largest dimension of
the winding does not exceed 5 mm in cross section
or length.
N/A
j: IEC 60245 Types 53, 57 and 87 supply cords have
a T rating of 60 °C;
IEC 60227 Types 52 and 53 supply cords have a T
rating of 70 °C;
IEC 60227 Types 56 and 57 supply cords have a T
rating of 90 °C.
N/A
TRANSIENT OVERVOLTAGES
The impulse test voltage has a no-load wave shape
corresponding to the 1,2/50 s standard impulse
specified in IEC 61180-1. It is supplied from a
generator having conventional impedance not
exceeding 42 . The impulse test voltage is applied
three times for each polarity with intervals of at least
1 s.
N/A
www.tuv.com
Page 3 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
16
LEAKAGE CURRENT AND ELECTRIC STRENGTH
16.3
Electric strength tests according to table 7
(accordance with IEC 61180-1)
Result - Remark
(See appended table)
Verdict
P
Note 2: The characteristics of the high-voltage
source used for the test are described in Table 5.
P
Delete the penultimate paragraph of the test
specification.
P
19
ABNORMAL OPERATION
19.1
Appliances incorporating contactors or relays
subjected to the test of 19.14.
N/A
19.7
In the second paragraph, replace “IEC 60252” by
“IEC 60252-1”.
N/A
19.11
Replace the second and third paragraphs by the
following:
N/A
Appliances incorporating an electronic circuit are
subjected to the tests of 19.11.3 and 19.11.4.
Appliances incorporating an electronic circuit that
relies upon a programmable component to function
correctly, subjected to the test of 19.11.4.8
N/A
In the existing third paragraph, replace “switch” by
“device” in two places.
N/A
In the sixth paragraph replace “all three” by “both”
and delete the last dashed item.
N/A
19.11.2
g) failure of an electronic power switching device in a
partial turn-on mode with loss of gate (base) control.
During this test, winding temperatures shall not
exceed the values given in 19.7.
N/A
19.11.4
In the first paragraph, replace “switch” by “device” in
three places.
N/A
www.tuv.com
Page 4 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
Verdict
In the last paragraph, replace "arresters" by
"protective devices“.
N/A
19.11.4.6
The appliance is subjected to the Class 3 voltage
dips and interruptions in accordance with IEC 610004-11
N/A
19.11.4.8
The appliance is supplied at rated voltage and
operated under normal operation. After 60s the
power supply is reduced to a level such that the
appliance ceases to respond or a programmable
component cease to operate.
N/A
The appliance continues to operate normally or
requires a manual operation to restart
N/A
After the tests, and when the appliance has cooled to
approximately room temperature, compliance with
Clause 8 shall not be impaired and the appliance
shall comply with 20.2 if it can still be operated.
N/A
After operation or interruption of a control, clearances
and creepage distances across the functional
insulation withstanding the electric strength test of
16.3. the test voltage being twice the working voltage
N/A
19.13
Appliances tested with an electronic switch in the off position, or in the stand-by mode:
- do not become operational, or
N/A
- if they become operational, do not result in a
dangerous malfunction during or after the tests of
19.11.4
N/A
Note: Unintended operation that may impair safety can result from careless use of
appliances, such as:
19.14
- storage of small appliances while connected to the
supply;
N/A
– placing flammable material on working surfaces of
heating appliances; or
N/A
– placing objects in areas near motorized appliances
that are not expected to start.
N/A
Appliances operated under the conditions of Clause
11. Contactors or relays contacts operating under the
conditions of clause 11 short-circuited
N/A
www.tuv.com
Page 5 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
22
CONSTRUCTION
22.2
Singe-pole switches and single-pole protective
devices for the disconnection of heating elements in
single-phase, permanently connected class 0I and
class I appliances, connected to the phase conductor
N/A
22.5
No risk of electric shock from charged capacitors
having a rated capacitance exceeding 0,1 F when
touching the pins of the plug, the appliance being
disconnected from the supply at the instant of voltage
peak
N/A
Delete the note
N/A
22.21
This requirement does not apply to magnesium
oxide and mineral ceramic fibres used for the
electrical insulation of heating elements.
Delete note 2
N/A
22.32
Insulating material in which heating conductors are
embedded is considered to be basic insulation
and not reinforced insulation.
Delete Note 1 and renumber existing Note 2 as
Note
Instead of first paragraph:
actuated in normal use shall not become live in the
event of a failure of basic insulation. If these
handles, levers and knobs are of metal and if their
shafts or fixings are likely to become live in the
event of a failure of basic insulation, they shall be
adequately covered by insulating material or their
accessible parts shall be separated from their
shafts or fixings by supplementary insulation.
N/A
22.35
Result - Remark
Verdict
N/A
N/A
N/A
22.40
Unless the appliance can operate continuously,
automatically or remotely without giving rise to a
hazard, appliances for remote operation being fitted
with a switch. The actuating member of the switch
being easily visible and accessible.
N/A
22.44
Appliances shall not have an enclosure that is
shaped or decorated like a toy
22.49
For remote operation, the duration of operation shall
be set before the appliance can be started, unless
the appliance switches off automatically or can
operate continuously without hazard
N/A
22.50
Controls incorporated in the appliance take priority
over controls actuated by remote operation.
N/A
P
www.tuv.com
Page 6 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
22.51
A control on the appliance shall be manually adjusted
to the setting for remote operation before the
appliance can be operated in this mode. There shall
be a visual indication on the appliance showing that
the appliance is adjusted for remote operation. The
manual setting and the visual indication of the remote
mode are not necessary on appliances that can
Result - Remark
Verdict
N/A
- operate continuously, or
- operate automatically, or
- be operated remotely,
without giving rise to a hazard.
22.52
Socket-outlets on appliances accessible to the user
in accordance with the socket-outlet system used in
the country in which the appliance is sold.
24
COMPONENTS
24.1
NOTE 1: Compliance with the IEC standard for the
relevant component does not necessarily ensure
compliance with the requirements of this standard.
P
NOTE 2: Motors are not required to comply with IEC
60034-1.
P
NOTE 3: Unless otherwise specified, the
requirements of Clause 29 of this standard apply
between live parts of components and accessible
parts of the appliance.
N/A
N/A
NOTE 4: Unless otherwise specified, the
Approved components used
requirements of 30.2 of this standard apply to parts of
non-metallic material in components including parts
of non-metallic material supporting current-carrying
connections inside components.
P
Components that have been previously tested and
shown to comply with the resistance to fire
requirements in the IEC standard for the relevant
component need not be retested provided that
P
– the severity specified in the component standard is
not less than the severity specified in 30.2 of this
standard and
– unless the preselection alternative is used, the test
report for the component states whether it complied
IEC standard for the relevant component with or
without flame. Flames existing for a cumulative time
not exceeding 2 s during the test are ignored.
www.tuv.com
Page 7 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
Verdict
If the above two conditions are not satisfied, the
component is tested as part of the appliance.
N/A
There are two levels of severity specified for
appliances for which 30.2.3 is applicable.
N/A
Components that have not been previously tested
and shown to comply with the IEC standard for the
relevant component are tested according to the
requirements of 30.2 of this standard.
N/A
In the first paragraph of the test specification, replace
“24.1.1 to 24.1.6” by “24.1.1 to 24.1.9”.
P
Renumber Note 2 as Note 5.
P
Lampholders and starterholders not being tested and
found to comply with the relevant IEC standard,
tested as a part of the appliance and additionally
according to the gauging and interchangeability
requirements of the relevant IEC standard.
P
NOTE 6: Where the relevant IEC standard specifies
these gauging and interchangeability requirements at
elevated temperatures, the temperatures measured
during the tests of Clause 11 are used.
N/A
24.1.7
If the remote operation of the appliance is via a
telecommunication network, the relevant standard for
the telecommunication interface circuitry in the
appliance is IEC 62151.
N/A
24.1.8
The relevant standard for thermal links is IEC 60691.
Thermal links not complying with IEC 60691 are
considered to be an intentionally weak part for the
purposes of Clause 19
P
24.1.9
Relays, other than motor starting relays, are tested
as part of the appliance. However, they are also
tested in accordance with Clause 17 of IEC 60730-1
under the maximum load conditions occurring in the
appliance for at least the number of operations in
24.1.4 selected according to the relay function in the
appliance.
N/A
25
SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS
25.7
Supply cords being one of the following types:
- rubber sheathed (at least 60245 IEC 53)
N/A
www.tuv.com
Page 8 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
Verdict
- polychloroprene sheathed (at least 60245 IEC 57)
N/A
- cross-linked polyvinyl chloride sheathed (at least
60245 IEC 87)
N/A
Polyvinyl chloride sheathed:
Not used if they are likely to touch metal parts having
a temperature rise exceeding 75K during the test of
Clause 11.
N/A
- light polyvinyl chloride sheathed cord (at least
60227 IEC 52), appliances not exceeding 3 kg
N/A
- ordinary polyvinyl chloride sheathed cord (at least
60227 IEC 53), other appliances
N/A
Heat resistant polyvinyl chloride sheathed:
Not used for type X attachment other than specially
prepared cords.
N/A
- Heat-resistant light polyvinyl chloride sheathed cord
(at least 60227 IEC 56), appliances not exceeding
3 kg
N/A
- heat-resistant polyvinyl chloride sheathed cord
(60227 IEC 57), other appliances
N/A
26
TERMINALS FOR EXTERNAL CONDUCTORS
26.2
NOTE: Conductors connected by soldering are not
considered to be positioned or fixed so that reliance
is not placed upon the soldering alone to maintain it
in position unless they are held in place near the
terminals independently of the solder.
N/A
In Table 13, replace the last two rows by the
following:
N/A
>32 and 50
6 and 10
6 to 16
>50 and 63
10 and 16
10 to 25
26.3
Compliance checked by inspection and by the test of
subclause 9.6 of IEC 60999-1.
26.11
Replace Notes 1 and 2 by the following:
NOTE: Conductors connected by soldering are not
considered to be positioned or fixed so that reliance
is not placed upon the soldering alone to maintain it
in position unless they are held in place near the
terminals independently of the solder.
P
N/A
www.tuv.com
Page 9 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
27
PROVISION FOR EARTHING
27.6
The printed conductors of printed circuit boards shall
not be used to provide earthing continuity in handheld appliances. They may be used to provide
earthing continuity in other appliances if at least two
tracks are used with independent soldering points
and the appliance complies with 27.5 for each circuit
28
SCREWS AND CONNECTIONS
Replace the penultimate row of Table 14 by the
following:
>4,7 and
28.3
5,3
0,8
2,0
Verdict
N/A
N/A
1,0
Thread-cutting (self-tapping) screws and thread
rolling screws shall only be used for electrical
connections if they generate a full form standard
machine screw thread. However, thread-cutting (selftapping) screws shall not be used if they are likely to
be operated by the user or installer.
N/A
Thread-cutting, thread rolling and space-threaded
screws may be used in connections providing
earthing continuity provided it is not necessary to
disturb the connection
N/A
– in normal use,
– during user maintenance,
– when replacing a supply cord having a type X
attachment, or
– during installation.
At least two screws must be used for each
connection providing earthing continuity unless the
screw forms a thread having a length of at least half
the diameter of the screw.
29
29.1
N/A
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
If coatings are used on printed circuit boards to
protect the microenvironment (Type 1 coating) or to
provide basic insulation (Type 2 coating), Annex J
applies. The microenvironment is pollution degree 1
under Type 1 coating. There are no clearance or
creepage distance requirements under Type 2
coating.
N/A
In Note 2, replace “suppression” by “protective”.
N/A
www.tuv.com
Page 10 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
Verdict
NOTE 6: For appliances intended for use at altitudes
exceeding 2 000 m, the altitude correction factors for
clearances specified in Table A.2 of IEC 60664-1
should be taken into account.
N/A
29.1.1
The values of Table 16, or the impulse voltage test of
Clause 14, are applicable.
N/A
29.2
NOTE 1 The working voltage for parts connected to
the neutral is the same as for parts connected to the
phase and this is the working voltage for basic
insulation. Add the following new note:
N/A
NOTE 6 In a double insulation system, the working
voltage for both the basic insulation and
supplementary insulation is taken as the working
voltage across the complete double insulation
system. It is not divided according to thickness and
dielectric constant of the basic insulation and
supplementary insulation.
N/A
30
RESISTANCE TO HEAT AND FIRE
30.2
Parts of non-metallic material adequately resistant to
ignition and spread of fire.
P
This requirement does not apply to decorative trims,
knobs and other parts unlikely to be ignited or to
propagate flames that originate inside the appliance.
N/A
Compliance checked by the test of 30.2.1.
In addition:
P
- attended appliances, 30.2.2 applies
- unattended appliances, 30.2.3 applies
Appliances for remote operation, 30.2.3 applies.
N/A
Base material of printed circuit board, 30.2.4 applies.
N/A
The tests are carried out on parts of non-metallic
material that have been removed from the appliance.
When the glow-wire test is carried out, the parts are
placed in the same orientation, as they would be in
normal use.
P
www.tuv.com
Page 11 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
30.2.1
Glow-wire test of IEC 60695-2-11 at 550 °C, unless
the material is classified at least HB40 according to
IEC 60695-11-10
P
Parts for which the glow-wire test cannot be carried
out meet the requirements in ISO9772 for category
HBF material
N/A
Appliances operated while attended, parts of nonmetallic material supporting current-carrying
connections, and parts of non-metallic material within
a distance of 3mm of such connections, are
subjected to the glow-wire test of IEC 60695-2-11.
N/A
The glow-wire test is not carried out on parts of
material classified as having a glow-wire flammability
index according to IEC 60695-2-12 of at least:
N/A
-750 °C, for connections carrying a current exceeding
0,5 A during normal operation
N/A
-650 °C, for other connections
N/A
Test as specified for an interposed shielding material
N/A
When the glow-wire test of IEC 60695-2-11 is carried
out, the temperatures are:
N/A
-750 °C, for connections carrying a current exceeding
0,5 A during normal operation
N/A
-650 °C, for other connections
N/A
Test not applicable to conditions as specified
N/A
30.2.2
30.2.3
30.2.3.1
Result - Remark
Verdict
Appliances operated while unattended, tested as
specified in 30.2.3.1 and 30.2.3.2
P
Tests not applicable to conditions as specified
P
Parts of non-metallic material supporting
connections that carry a current exceeding
0,2 A during normal operation, and parts of nonmetallic material within a distance of 3 mm of such
connections, are subjected to the glow-wire test of
IEC 60695-2-11 with a test severity of 850 °C.
However, the glow-wire test is not carried out on
parts of material classified as having a glow-wire
flammability index of at least 850 °C according to
IEC 60695-2-12. If the glow-wire flammability index
is not available for a sample with a thickness within
± 0,1 mm of the relevant part, then the test sample
shall have a thickness equal to the nearest
preferred value specified in IEC 60695-2-12 that is
no thicker than the relevant part.
Approved terminal block
P
www.tuv.com
Page 12 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
Result - Remark
Verdict
NOTE 1 The preferred values in IEC 60695-2-12
are 0,75 mm ± 0,1 mm, 1,5 mm ± 0,1 mm and 3,0
mm ± 0,2 mm.
N/A
NOTE 2 Contacts in components such as switch
contacts are considered to be connections.
N/A
NOTE 3 The tip of the glow-wire is applied to the
part in the vicinity of the connection.
N/A
The glow-wire test is also not carried out on small
parts that comply with the needle-flame test of
Annex E or on small parts of material classified as
V-0 or V-1 according to IEC 60695-11-10 provided
that the test sample used for the classification was
no thicker than the relevant part of the appliance.
N/A
NOTE 4 Small parts are as defined in IEC 60695-4.
N/A
Where a non-metallic material is within 3 mm of a
current carrying connection, but is shielded from the
connection by a different material, the glow-wire test
of IEC 60695-2-11 is carried out at the relevant
temperature with the tip of the glow-wire applied to
the interposed shielding material with the shielded
material in place and not directly to the shielded
material.
N/A
www.tuv.com
Page 13 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
30.2.3.2
Parts of non-metallic material supporting currentcarrying connections, and parts of non-metallic
material within a distance of 3 mm of such
connections, are subjected to the glow-wire test of
IEC 60695-2-11. However, the glow-wire test is not
carried out on parts of material classified as having
a glow-wire ignition temperature according to IEC
60695-2-13 of at least
Result - Remark
Verdict
N/A
– 775 °C, for connections that carry a current
exceeding 0,2 A during normal operation,
– 675 °C, for other connections.
If the glow-wire ignition temperature is not available
for a sample with a thickness within
N/A
± 0,1 mm of the relevant part, then the test sample
shall have a thickness equal to the nearest
preferred value specified in IEC 60695-2-13 that is
no thicker than the relevant part.
NOTE 1 The preferred values in IEC 60695-2-13
are 0,75 mm ± 0,1 mm, 1,5 mm ± 0,1 mm and 3,0
mm ± 0,2 mm.
N/A
Where an non-metallic material is within 3 mm of a
current carrying connection, but is shielded from the
connection by a different material, the glow-wire test
of IEC 60695-2-11 is carried out at the relevant
temperature with the tip of the glow-wire applied to
the interposed shielding material with the shielded
material in place and not directly to the shielded
material.
N/A
When the glow-wire test of IEC 60695-2-11 is
carried out, the temperatures are
N/A
– 750 °C, for connections that carry a current
exceeding 0,2 A during normal operation,
– 650 °C, for other connections.
NOTE 2 Contacts in components such as switch
contacts are considered to be connections.
N/A
NOTE 3 The tip of the glow-wire is applied to the
part in the vicinity of the connection.
N/A
www.tuv.com
Page 14 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
If parts that withstand the glow-wire test of IEC
60695-2-11, but during the test produce a flame
that persists for longer than 2 s, then these parts
and adjacent parts are further tested as follows.
Result - Remark
Verdict
N/A
Parts above the connection within the envelope of
a vertical cylinder having a diameter of 20 mm and
a height of 50 mm are subjected to the needleflame test of Annex E.
However, parts shielded by a flame barrier that
meets the needle-flame test of Annex E are not
tested.
30.2.4
32
D
The needle-flame test is not carried out on parts of
material classified as V-0 or V-1 according to IEC
60695-11-10 provided that the test sample used for
the classification was no thicker than the relevant
part of the appliance.
N/A
Base material of printed circuit boards subjected to
needle-flame test of annex E
N/A
Test is not applicable to conditions as specified
N/A
RADIATION, TOXICITY AND SIMILAR HAZARDS
Appliance shall not emit harmful radiation, present a
toxic or similar hazard due to their operation in
normal use
P
Compliance is checked by the limits or tests specified
in Part 2. However, if no limits or tests are specified
in Part 2, then the appliance is deemed to comply
with the requirement without testing.
P
ANNEX D (NORMATIVE)
THERMAL MOTOR PROTECTORS
Delete the note
E
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST
Needle-flame test carried out in accordance with
IEC 60695-11-5, with the following modifications:
7
P
N/A
Severities
The duration of application of the test flame is 30 s
±1s
N/A
www.tuv.com
Page 15 of 16
Report No.: 28207876 001
Attachment 1
IEC/EN 60335-1/A2
Clause
Requirement + Test
9
Test procedure
9.1
The specimen so arranged that the flame can be
applied to a vertical or horizontal edge as shown in
the examples of figure 1
N/A
9.2
The first paragraph does not apply
N/A
If possible, the flame is applied at least 10 mm from a
corner
N/A
The test is carried out on one specimen
N/A
If the specimen does not withstand the test, the test
may be repeated on two additional specimens, both
withstanding the test
N/A
9.3
11
J
Result - Remark
Evaluation of test results
The duration of burning not exceeding 30 s
N/A
However, for printed circuit boards, the duration of
burning not exceeding 15 s
N/A
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
Testing of protective coatings of printed circuit boards
carried out in accordance with IEC 60664-3 with the
following modifications:
5.7
N/A
Additional tests
This subclause is not applicable
Q
N/A
Rapid change of temperature
Severity 1 is specified
5.9
N/A
Cold
The test is carried out at -25°C
5.7.3
N/A
Conditioning of the test specimens
When production samples are used, three samples
of the printed circuit board are tested
5.7.1
Verdict
N/A
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
Replace "19.10 " by " 19.10 and 19.14" in two places.
N/A
www.tuv.com
Page 16 of 16
Report No.: 28207876 001
Attachment 1
EN 60335-1/A12
Clause
Requirement + Test
Result - Remark
Verdict
29.
CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION
29.3.
Replace the third dashed item by:
Assessment of thermal quality of the material
combined with an electric strength test.
N/A
29.3.Z1
If accessible reinforced insulation consist of a single
layer, the thickness of this layer comply with Table Z1
N/A
EN 60335-1/A13:2008
Clause
Requirement – Test
24.
COMPONENTS
24.1.7.
Remote operation is via telecommunication network.
(Telecommunication interface circuity: EN 41003 and
EN 60950-1:2006, subclause 6.3)
Result – Remark
Verdict
N/A
IEC 60335-2-80/A2: 2008; EN 60335-2-80/A2: 2009
Clause
Requirement – Test
21.
MECHANICAL STRENGTH
21.101.
The test probe is applied with a force not exceeding
5N
Result – Remark
Verdict
N/A
ANNEX EMF
The Tested product also complies to the requirements of EN 62233: 2008

Limit ……………100%
P
Measured max. : 0,628 %
Test Report issued under the responsibility of:
Attachment 2
TEST REPORT
IEC/EN 60598-2-1
Luminaires
Part 2: Particular requirements:
Section One – Fixed general purpose luminaires
Report Reference No......................:
28207876 001
Date of issue.....................................:
14-01-2010
Total number of pages ......................
28
CB/CCA Testing Laboratory..........:
MEEI Kft. member of TÜV Rheinland Group
Address ............................................:
H-1132 Budapest, Váci út 48/a-b., Hungary
Applicant’s name............................:
Ventilation Systems JSC
Address ............................................:
Mikhaila Kotzubinskiego St., Kiev, UA-01030, Ukraine
Test specification:
Standard ...........................................:
IEC 60598-2-1:1979 (First Edition) + A1:1987 used in
conjunction with IEC 60598-1:2003+A1:2006
EN 60598-2-1:1989 used in conjunction with
EN 60598-1:2004+A1:2006
Test procedure .................................:
CB / CCA
Non-standard test method…………..:
N/A
Test Report Form No......................:
IECEN60598_2_1D
Test Report Form(s) Originator ........:
Intertek Semko AB
Master TRF.......................................:
2007-05
Copyright © 2007 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
If this Test Report Form is used by non-CCA members, the CIG logo and the reference to the CCA Procedure shall be
removed.
This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory and
appended to a CCA Test Certificate issued by an NCB in accordance with CCA
page 2 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Test item description .....................:
Lampholder (Lampholder is a structural part of fans)
Trade Mark .......................................:
VENTS
Manufacturer ....................................:
Ventilation Systems JSC; 1, Mikhaila Kotzubinskiego St., Kiev, UA01030, Ukraine
Model/Type reference of fans...........:
VENTS yyy M w XY
Ratings .............................................:
12 V~; 0-45 °C; IP 24; Class III
page 3 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Testing procedure and testing location:
CB/CCA Testing Laboratory:
MEEI Kft. member of TÜV Rheinland Group
Testing location/ address ..........................: H-1132 Budapest, Váci út 48/a-b., Hungary
Associated CB Laboratory:
Testing location/ address ..........................:
Tested by (name + signature) .........: Ferenc Horvát
Approved by (+ signature)...............: Zoltán Zsákai
Testing procedure: TMP
Tested by (name + signature) .........: Approved by (+ signature)...............: Testing location/ address ..........................: Testing procedure: WMT
Tested by (name + signature) .........: Witnessed by (+ signature) .............: Approved by (+ signature)...............: Testing location/ address ..........................: Testing procedure: SMT
Tested by (name + signature) .........: Approved by (+ signature)...............: Supervised by (+ signature) ............: Testing location/ address ..........................: Testing procedure: RMT
Tested by (name + signature) .........: Approved by (+ signature)...............: Supervised by (+ signature) ............: Testing location/ address ..........................: -
Summary of testing: Tests were conducted on models VENTS 100 Xstar 12.
During the documentation check the English User’s Manual was evaluated.
Factory location: 36, 40-Richchya Zhovtnya Str. Boyarka 08150, Kiev Region, Ukraine.
Verdict
page 4 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Tests performed (name of test and test clause):-
Result - Remark
Testing location:
MEEI Kft. member of TÜV Rheinland Group
H-1132 Budapest, Váci út 48/a-b., Hungary
Summary of compliance with National Differences: –
Copy of marking plate: -
Verdict
page 5 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Test item particulars .............................................. :
-
Classification of installation and use ........................ :
Class III
Supply Connection ................................................... :
Permanent connection, supply cord is not provided
.................................................................................. :
-
.................................................................................. :
-
Possible test case verdicts:
- test case does not apply to the test object ............. :
N/A
- test object does meet the requirement................... :
P (Pass)
- test object does not meet the requirement............. :
F (Fail)
Testing..................................................................... :
Date of receipt of test item ....................................... :
16-11-2009
Date (s) of performance of tests............................... :
16-11-2009 – 14-01-2009
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Note: EN Group Differences together with National Differences and Special National Conditions, if
any, are in the Appendix to the main body of this TRF.
Throughout this report a comma (point) is used as the decimal separator.
Clause numbers between brackets refer to clauses in IEC 60598-1
General product information:
The fans are designed for ventilation of domestic and similar purposes and for continuous operation.
Lampholder is a structural part of fans.
page 6 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
1.2 (0)
GENERAL TEST REQUIREMENTS
1.2 (0.1)
Information for luminaire design considered
Result - Remark
Standard
Yes
Verdict

No
1.2 (0.3)
More sections applicable ........................................: Yes
1.4 (2)
CLASSIFICATION
1.4 (2.2)
Type of protection................................................. : Class III;

1.4 (2.3)
Degree of protection (Requirement: Ordinary)..... : IP 24

1.4 (2.4)
Yes
Luminaire only suitable for non-combustible
surfaces ............................................................... :
No

Yes
Luminaire suitable for normally flammable
surfaces ................................................................ :
No

Yes
Luminaire suitable to be covered by insulating
material................................................................. :
No

Luminaire for normal use ..................................... : Yes
No

Luminaire for rough service ................................. : Yes
No

1.4 (2.5)
No

1.5 (3)
MARKING
P
1.5 (3.2)
Mandatory markings
P
Position of the marking
P
Format of symbols/text
P
Additional information
P
1.5 (3.3)
Language of instructions
English
P
1.5 (3.3.1)
Combination luminaires
N/A
1.5 (3.3.2)
Nominal frequency in Hz
P
1.5 (3.3.3)
Operating temperature
N/A
1.5 (3.3.4)
Symbol or warning notice
N/A
1.5 (3.3.5)
Wiring diagram
N/A
1.5 (3.3.6)
Special conditions
N/A
1.5 (3.3.7)
Metal halide lamp luminaire – warning
N/A
1.5 (3.3.8)
Limitation for semi-luminaires
N/A
1.5 (3.3.9)
Power factor and supply current
N/A
1.5 (3.3.10)
Suitability for use indoors
N/A
1.5 (3.3.11)
Luminaires with remote control
N/A
page 7 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
1.5 (3.3.12)
Clip-mounted luminaire – warning
N/A
1.5 (3.3.13)
Specifications of protective shields
N/A
1.5 (3.3.14)
Symbol for nature of supply
1.5 (3.3.15)
Rated current of socket outlet
N/A
1.5 (3.3.16)
Rough service luminaire
N/A
1.5 (3.3.17)
Mounting instruction for type Y, type Z and some
type X attachments
N/A
1.5 (3.3.18)
Non-ordinary luminaires with PVC cable
N/A
1.5 (3.4)
Test with water
P
Test with hexane
P
Legible after test
P
Label attached
P
1.6 (4)
CONSTRUCTION
P
1.6 (4.2)
Components replaceable without difficulty
1.6 (4.3)
Wireways smooth and free from sharp edges
P
1.6 (4.4)
Lampholders
P
1.6 (4.4.1)
Integral lampholder
P
1.6 (4.4.2)
Wiring connection
P
1.6 (4.4.3)
Lampholder for end-to-end mounting
N/A
1.6 (4.4.4)
Positioning
N/A
- pressure test (N) ................................................ : -
N/A
- bending test (N) ................................................. : -
N/A
1.6 (4.4.5)
Peak pulse voltage
N/A
1.6 (4.4.6)
Centre contact
N/A
1.6 (4.4.7)
Parts in rough service luminaires resistant to
tracking
N/A
1.6 (4.4.8)
Lamp connectors
1.6 (4.4.9)
Caps and bases correctly used
N/A
1.6 (4.5)
Starter holders
N/A
Starter holder in luminaires other than class II
N/A
Starter holder class II construction
N/A
1.6 (4.6)
Result - Remark
Verdict
P
N/A
P
Terminal blocks
P
Tails
P
page 8 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Unsecured blocks
1.6 (4.7)
Terminals and supply connections
1.6 (4.7.1)
Contact to metal parts
1.6 (4.7.2)
Test 8 mm live conductor
Test 8 mm earth conductor
Verdict
N/A
P
N/A
P
N/A
1.6 (4.7.3)
Terminals for supply conductors
P
1.6 (4.7.3.1)
Welded connections:
N/A
- stranded or solid conductor
N/A
- spot welding
N/A
- welding between wires
N/A
- Type Z attachment
N/A
- mechanical test according to 15.8.2
N/A
- electrical test according to 15.9
N/A
- heat test according to 15.9.2.3 and 15.9.2.4
N/A
1.6 (4.7.4)
Terminals other than supply connection
1.6 (4.7.5)
Heat-resistant wiring/sleeves
N/A
1.6 (4.7.6)
Multi-pole plug
N/A
- test at 30 N
N/A
Switches:
N/A
- adequate rating
N/A
- adequate fixing
N/A
- polarized supply
N/A
- compliance with 61058-1 for electronic switches
N/A
1.6 (4.9)
Insulating lining and sleeves
N/A
1.6 (4.9.1)
Retainement
N/A
Method of fixing .................................................... : -
N/A
Insulated linings and sleeves
N/A
a) & c) Insulation resistance and electric strength
N/A
b) Ageing test. Temperature (°C) ......................... : -
N/A
1.6 (4.10)
Insulation of Class II luminaires
N/A
1.6 (4.10.1)
No contact, mounting surface – accessible metal
parts – wiring of basic insulation
N/A
Safe installation fixed luminaires
N/A
Capacitors and switches
N/A
1.6 (4.8)
1.6 (4.9.2)
P
page 9 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Interference suppression capacitors according to
IEC 60384-14
N/A
Assembly gaps:
N/A
- not coincidental
N/A
- no straight access with test probe
N/A
Retainment of insulation:
N/A
- fixed
N/A
- unable to be replaced; luminaire inoperative
N/A
- sleeves retained in position
N/A
- lining in lampholder
N/A
1.6 (4.11)
Electrical connections
P
1.6 (4.11.1)
Contact pressure
P
1.6 (4.11.2)
Screws:
N/A
- self-tapping screws
N/A
- thread-cutting screws
N/A
- at least two self-tapping screws
N/A
Screw locking:
N/A
- spring washer
N/A
- rivets
N/A
1.6 (4.10.2)
1.6 (4.10.3)
1.6 (4.11.3)
1.6 (4.11.4)
Material of current-carrying parts
1.6 (4.11.5)
No contact to wood
N/A
1.6 (4.11.6)
Electro-mechanical contact systems
N/A
1.6 (4.12)
Mechanical connections and glands
P
1.6 (4.12.1)
Screws not made of soft metal
N/A
Screws of insulating material
N/A
Torque test: torque (Nm); part .............................. : -
N/A
Torque test: torque (Nm); part .............................. : -
N/A
Torque test: torque (Nm); part .............................. : -
N/A
1.6 (4.12.2)
Screws with diameter < 3 mm screwed into metal
N/A
1.6 (4.12.4)
Locked connections:
1.6 (4.12.5)
P
- fixed arms; torque (Nm)...................................... : -
N/A
- lampholder; torque (Nm)..................................... : -
N/A
- push-button switches; torque 0,8 Nm................. : -
N/A
Screwed glands; force (N) .................................... : -
N/A
page 10 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
1.6 (4.13)
Mechanical strength
P
1.6 (4.13.1)
Impact tests:
P
- fragile parts; energy (Nm)................................... : - other parts; energy (Nm) .................................... : 0,35
Verdict
N/A
P
1) live parts
N/A
2) linings
N/A
3) protection
P
4) covers
P
1.6 (4.13.3)
Straight test finger
P
1.6 (4.13.4)
Rough service luminaries
N/A
- IP54 or higher
N/A
a) fixed
N/A
b) hand-held
N/A
c) delivered with a stand
N/A
d) for temporary installations and suitable for
mounting on a stand
N/A
1.6 (4.13.6)
Tumbling barrel
N/A
1.6 (4.14)
Suspensions and adjusting devices
N/A
1.6 (4.14.1)
Mechanical load:
N/A
A) four times the weight
N/A
B) torque 2,5 Nm
N/A
C) bracket arm; bending moment (Nm) ................ : -
N/A
D) load track-mounted luminaires
N/A
E) clip-mounted luminaires, glass-shelve.
Thickness (mm) ................................................... :
N/A
Metal rod. diameter (mm) .................................... : -
N/A
Fixed luminaire or independent control gear
without fixing devices
N/A
Load to flexible cables
N/A
Mass (kg) ............................................................. : -
N/A
Stress in conductors (N/mm²) .............................. : -
N/A
Mass (kg) of semi-luminaire ................................. : -
N/A
Bending moment (Nm) of semi-luminaire ............ : -
N/A
Adjusting devices:
N/A
1.6 (4.14.2)
1.6 (4.14.3)
page 11 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
- flexing test; number of cycles ............................. : -
N/A
- strands broken
N/A
- electric strength test afterwards
N/A
1.6 (4.14.4)
Telescopic tubes: cords not fixed to tube; no
strain on conductors
N/A
1.6 (4.14.5)
Guide pulleys
N/A
1.6 (4.14.6)
Strain on socket-outlets
N/A
1.6 (4.15)
Flammable materials:
P
- glow-wire test 650 °C
- spacing ≥ 30 mm
N/A
- screen withstanding test of 13.3.1
N/A
- screen dimensions
N/A
- no fiercely burning material
1.6 (4.15.2)
1.6 (4.16)
1.6 (4.16.2)
P
- thermal protection
N/A
- electronic circuits exempted
N/A
Luminaires made of thermoplastic material with lamp control gear
N/A
a) construction
N/A
b) temperature sensing control
N/A
c) surface temperature
N/A
Luminaires marked with F-symbol
No lamp control gear
1.6 (4.16.1)
No such material
P
(Compliance with Section 12)
P
Lamp control gear spacing:
N/A
- spacing 35 mm
N/A
- spacing 10 mm
N/A
Thermal protection:
N/A
- in lamp control gear
N/A
- external
N/A
- fixed position
N/A
- temperature marked lamp control gear
N/A
1.6 (4.16.3)
“F” curve measured
(See 12.6)
N/A
1.6 (4.17)
Drain holes
Permanent ventilation, low
power of light source
N/A
Clearance at least 5 mm
1.6 (4.18)
Resistance to corrosion:
N/A
page 12 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
Verdict
1.6 (4.18.1)
- rust-resistance
N/A
1.6 (4.18.2)
- season cracking in copper
N/A
1.6 (4.18.3)
- corrosion of aluminium
N/A
1.6 (4.19)
Ignitors compatible with ballast
N/A
1.6 (4.20)
Rough service vibration
N/A
1.6 (4.21)
Protective shield:
1.6 (4.21.1)
Shield fitted
N/A
1.6 (4.21.2)
Particles from a shattering lamp not impair safety
N/A
1.6 (4.21.3)
No direct path
N/A
1.6 (4.21.4)
Impact test on shield
N/A
Glow-wire test on lamp compartment
N/A
1.6 (4.22)
Attachments to lamps
N/A
1.6 (4.23)
Semi-luminaires comply Class II
N/A
1.6 (4.24)
UV radiation, metal halide lamps
N/A
1.6 (4.25)
No sharp point or edges
1.6 (4.26)
Short-circuit protection:
1.6 (4.26.1)
Uninsulated accessible SELV parts
N/A
1.6 (4.26.2)
Short-circuit test
N/A
1.6 (4.26.3)
Test chain according to Figure 29
N/A
1.7 (11)
CREEPAGE DISTANCES AND CLEARANCES
P
Working voltage (V) .............................................. : 12

Voltage form
Sinusoidal
Non-sinusoidal

PTI
< 600

> 600
Rated pulse voltage (kV) ...................................... : -

crreq = 1,9 mm crmeas > 4 mm
(1) Current-carrying parts of different polarity: cr
(mm); cl (mm) ....................................................... : clreq = 0,8 mm clmeas > 4 mm
P
(2) Current-carrying parts and accessible parts: cr crreq = 1,9 mm crmeas > 10 mm
(mm); cl (mm) ....................................................... : clreq = 0,8 mm clmeas > 10 mm
P
(3) Parts becoming live due to breakdown of
basic insulation and metal parts:
cr (mm); cl (mm) ................................................... :
N/A
(4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)................................ :
N/A
page 13 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
(5) Not used
Verdict

(6) Current-carrying parts and supporting surface: cr (mm); cl (mm) ................................................... :
N/A
1.8 (7)
PROVISION FOR EARTHING
N/A
1.8 (7.2.1
+ 7.2.3)
Accessible metal parts
N/A
Metal parts in contact with supporting surface
N/A
Resistance < 0,5 Ω
N/A
Two self-tapping screws used
N/A
Thread-forming screws
N/A
Thread-forming screw used in a grove
N/A
Earth makes contact first
N/A
1.8 (7.2.2
+ 7.2.3)
Earth continuity in joints etc.
N/A
1.8 (7.2.4)
Locking of clamping means
N/A
Compliance with 4.7.3
N/A
1.8 (7.2.5)
Earth terminal integral part of connector socket
N/A
1.8 (7.2.6)
Earth terminal adjacent to mains terminals
N/A
1.8 (7.2.7)
Electrolytic corrosion of the earth terminal
N/A
1.8 (7.2.8)
Material of earth terminal
N/A
Contact surface bare metal
N/A
Class II luminaire for looping-in
N/A
Double or reinforced insulation to functional earth
N/A
Earthing core coloured green-yellow
N/A
Length of earth conductor
N/A
1.8 (7.2.10)
1.8 (7.2.11)
1.9 (14)
1.9 (15)
SCREW TERMINALS
Separately approved; component list
(see Annex 1)
P
Part of the luminaire
(see Annex 3)
P
SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS
Separately approved; component list
(see Annex 1)
N/A
Part of the luminaire
(see Annex 4)
N/A
page 14 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
1.10 (5)
EXTERNAL AND INTERNAL WIRING
1.10 (5.2)
Supply connection and external wiring
P
1.10 (5.2.1)
Means of connection............................................. : terminal block
P
1.10 (5.2.2)
Type of cable ........................................................ : -
N/A
Nominal cross-sectional area (mm²)..................... : -
N/A
Cables equal to IEC 60227 or IEC 60245
N/A
-
Verdict
1.10 (5.2.3)
Type of attachment, X, Y or Z
N/A
1.10 (5.2.5)
Type Z not connected to screws
N/A
1.10 (5.2.6)
Cable entries:
N/A
- suitable for introduction
P
- adequate degree of protection
P
1.10 (5.2.7)
Cable entries through rigid material have rounded
edges
P
1.10 (5.2.8)
Insulating bushings:
N/A
- suitably fixed
N/A
- material in bushings
N/A
- material not likely to deteriorate
N/A
- tubes or guards made of insulating material
N/A
1.10 (5.2.9)
Locking of screwed bushings
N/A
1.10 (5.2.10)
Cord anchorage:
P
- covering protected from abrasion
P
- clear how to be effective
P
- no mechanical or thermal stress
P
- no tying of cables into knots etc.
P
- insulating material or lining
P
1.10
(5.2.10.1)
Cord anchorage for type X attachment:
a) at least one part fixed
N/A
b) types of cable
N/A
c) no damaging of the cable
N/A
d) whole cable can be mounted
N/A
e) no touching of clamping screws
N/A
f) metal screw not directly on cable
Cord anchorage of fan
N/A
g) replacement without special tool
Cord anchorage of fan
N/A
page 15 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Glands not used as anchorage
Cord anchorage of fan
N/A
Labyrinth type anchorages
Cord anchorage of fan
N/A
1.10
(5.2.10.2)
Adequate cord anchorage for type Y and type Z
attachment
N/A
1.10
(5.2.10.3)
Tests:
N/A
- impossible to push cable; unsafe
N/A
- pull test: 25 times; pull (N) .................................. : -
N/A
- torque test: torque (Nm) ..................................... : -
N/A
- displacement ≤ 2 mm
N/A
- no movement of conductors
N/A
- no damage of cable or cord
N/A
1.10 (5.2.11)
External wiring passing into luminaire
P
1.10 (5.2.12)
Looping-in terminals
N/A
1.10 (5.2.13)
Wire ends not tinned
P
Wire ends tinned: no cold flow
N/A
Mains plug same protection
N/A
Class III luminaire plug
N/A
Appliance inlets (IEC 60320)
N/A
Appliance couplers of class II type
N/A
1.10 (5.2.17)
No standardized interconnecting cables properly
assembled
N/A
1.10 (5.2.18)
Used plug in accordance with
N/A
- IEC 60083
N/A
- other standard
N/A
1.10 (5.2.14)
1.10 (5.2.16)
1.10 (5.3)
Internal wiring
P
1.10 (5.3.1)
Internal wiring of suitable size and type
P
Through wiring
N/A
- not delivered/ mounting instruction
N/A
- factory assembled
N/A
- socket outlet loaded (A)...................................... : -
N/A
- temperatures ...................................................... : (see Annex 2)
N/A
Green-yellow for earth only
N/A
1.10 (5.3.1.1) Internal wiring connected directly to fixed wiring
page 16 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Cross-sectional area (mm²) .................................. : 0,5
P
Insulation thickness
P
Extra insulation added where necessary
N/A
1.10 (5.3.1.2) Internal wiring connected to fixed wiring via internal current-limiting device
N/A
Adequate cross-sectional area and insulation
thickness
1.10 (5.3.1.3) Double or reinforced insulation for class II
N/A
1.10 (5.3.1.4) Conductors without insulation
N/A
1.10 (5.3.1.5) SELV current-carrying parts
N/A
1.10 (5.3.1.6) Insulation thickness other than PVC or rubber
N/A
1.10 (5.3.2)
1.10 (5.3.3)
Sharp edges etc.
P
No moving parts of switches etc.
N/A
Joints, raising/lowering devices
N/A
Telescopic tubes etc.
N/A
No twisting over 360°
P
Insulating bushings:
N/A
- suitable fixed
N/A
- material in bushings
N/A
- material not likely to deteriorate
N/A
- cables with protective sheath
N/A
1.10 (5.3.4)
Joints and junctions effectively insulated
N/A
1.10 (5.3.5)
Strain on internal wiring
N/A
1.10 (5.3.6)
Wire carriers
N/A
1.10 (5.3.7)
Wire ends not tinned
N/A
Wire ends tinned: no cold flow
N/A
1.11 (8)
PROTECTION AGAINST ELECTRIC SHOCK
N/A
1.11 (8.2.1)
Live parts not accessible
Class III
N/A
Basic insulated parts not used on the outer
surface without appropriate protection
N/A
Protection in any position
N/A
Double-ended tungsten filament lamp
N/A
Insulation lacquer not reliable
N/A
Double-ended high pressure discharge lamp
N/A
page 17 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Relevant warning according to 3.2.18 fitted to the
luminaire
N/A
1.11 (8.2.2)
Portable luminaire adjusted in most unfavourable
position
N/A
1.11 (8.2.3)
Class II luminaire:
N/A
- basic insulated metal parts not accessible during
starter or lamp replacement
N/A
- basic insulation not accessible other than during
starter or lamp replacement
N/A
- glass protective shields not used as
supplementary insulation
N/A
Class I luminaire with BC lampholder
N/A
Portable luminaire:
N/A
- protection independent of supporting surface
N/A
- terminal block completely covered
N/A
1.11 (8.2.5)
Compliance with the standard test finger or
relevant probe
N/A
1.11 (8.2.6)
Covers reliably secured
N/A
1.11 (8.2.7)
Discharging of capacitors ≥ 0,5 µF
N/A
Portable plug connected luminaire with capacitor
N/A
Other plug connected luminaire with capacitor
N/A
Discharge device on or within capacitor
N/A
Discharge device mounted separately
N/A
1.11 (8.2.4)
1.12 (12)
ENDURANCE TEST AND THERMAL TEST
1.12 (12.3)
Endurance test:
1.12 (12.3.2)
- mounting-position ............................................... : horizontal axis

- test temperature (°C) .......................................... : 45

- total duration (h) ................................................. : 168

- supply voltage: Un factor; calculated voltage (V): 1,1xUn (13,2)

- lamp used ........................................................... : LED MR-16

After endurance test:
P
- no part unserviceable
P
- luminaire not unsafe
P
- no damage to track system
N/A
page 18 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
- marking legible
P
- no cracks, deformation etc.
P
1.12 (12.4)
Thermal test (normal operation)
(see Annex 2)
1.12 (12.5)
Thermal test (abnormal operation)
N/A
1.12 (12.6)
Thermal test (failed lamp control gear condition):
N/A
1.12 (12.6.1)
Through wiring or looping-in wiring loaded by a
current of (A) ........................................................ :

- case of abnormal conditions............................... : -

- electronic lamp control gear
1.12 (12.6.2)
-
P
N/A
- measured winding temperature (°C): at 1,1 Un . : -

- measured mounting surface temperature (°C) at 1,1 Un ................................................................... :
N/A
- calculated mounting surface temperature (°C) .. : -
N/A
- track-mounted luminaires
N/A
Temperature sensing control
N/A
- case of abnormal conditions............................... : -

- thermal link
N/A
- manual reset cut-out
N/A
- auto reset cut-out
N/A
- measured mounting surface temperature (°C) ... : -
N/A
- track-mounted luminaires
N/A
1.12 (12.7)
Thermal test (failed lamp control gear in plastic luminaires):
N/A
1.12 (12.7.1)
Luminaire without temperature sensing control
N/A
1.12
(12.7.1.1)
Luminaire with fluorescent lamp
N/A
70W
Test method 12.7.1.1 or Annex V......................... : Test according to 12.7.1.1:

N/A
- case of abnormal conditions

- Ballast failure at supply voltage (V) ................... : -

- Components retained in place after the test
N/A
- Test with standard test finger after the test
N/A
Test according to Annex V:
N/A
- case of abnormal conditions

- measured winding temperature (°C): at 1,1 Un.. : -

page 19 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
1.12
(12.7.1.2)
1.12
(12.7.1.3)
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
- measured temperature of fixing point/exposed
part (°C): at 1,1 Un................................................ :

- calculated temperature of fixing point/exposed
part (°C) ................................................................ :

Ball-pressure test:
N/A
- part tested; temperature (°C).............................. : -
N/A
- part tested; temperature (°C).............................. : -
N/A
Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA
- case of abnormal conditions

- measured winding temperature (°C): at 1,1 Un.. : -

- measured temperature of fixing point/exposed
part (°C): at 1,1 Un................................................ :

- calculated temperature of fixing point/exposed
part (°C) ................................................................ :

Ball-pressure test:
N/A
- part tested; temperature (°C).............................. : -
N/A
- part tested; temperature (°C).............................. : -
N/A
Luminaire with short circuit proof transformers
10 VA
N/A
- case of abnormal conditions
1.12 (12.7.2)
Verdict

- Components retained in place after the test
N/A
- Test with standard test finger after the test
N/A
Luminaire with temperature sensing control
N/A
- thermal link
Yes
No

- manual reset cut-out
Yes
No

- auto reset cut-out
Yes
No

- case of abnormal conditions

- highest measured temperature of fixing
point/exposed part (°C):........................................ :

Ball-pressure test:
N/A
- part tested; temperature (°C).............................. : -
N/A
- part tested; temperature (°C).............................. : -
N/A
page 20 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
Verdict
1.13 (9)
RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE
P
1.13 (9.2)
Tests for ingress of dust, solid objects and moisture:
P
- classification according to IP .............................. : IP 24

- mounting position during test ............................. : as indicated in the
manufacturer’s mounting
instructions

- fixing screws tightened; torque (Nm).................. : -

- tests according to clauses .................................. : 9.2.5.

- electric strength test afterwards
P
a) no deposit in dust-proof luminaire
N/A
b) no talcum in dust-tight luminaire
N/A
c) no trace of water on current-carrying parts or
where it could become a hazard
P
d) i) For luminaires without drain holes – no water
entry
P
d) ii) For luminaires with drain holes – no
hazardous water entry
N/A
e) no water in watertight luminaire
N/A
f) no contact with live parts (IP 2X)
Class III
N/A
f) no entry into enclosure (IP 3X and IP 4X)
N/A
f) no contact with live parts (IP3X and IP4X)
N/A
1.13 (9.3)
Humidity test 48 h
P
1.14 (10)
INSULATION RESISTANCE AND ELECTRIC STRENGTH
P
1.14 (10.2.1)
Insulation resistance test
P
Cable or cord covered by metal foil or replaced by a metal rod of mm Ø ............................................ :

Insulation resistance (MΩ)

SELV:
P
- between current-carrying parts of different
1 MΩ
polarity .................................................................. :
P
- between current-carrying parts and mounting
1 MΩ
surface .................................................................. :
P
- between current-carrying parts and metal parts 1 MΩ
of the luminaire ..................................................... :
P
Other than SELV:
N/A
page 21 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
1.14 (10.2.2)
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
- between live parts of different polarity................ : -
N/A
- between live parts and mounting surface........... : -
N/A
- between live parts and metal parts..................... : -
N/A
- between live parts of different polarity through
action of a switch .................................................. :
N/A
Electric strength test
P
Dummy lamp
N/A
Luminaires with ignitors after 24 h test
N/A
Luminaires with manual ignitors
N/A
Test voltage (V):
N/A
SELV:
P
500 V
- between current-carrying parts of different
polarity .................................................................. :
P
500 V
- between current-carrying parts and mounting
surface .................................................................. :
P
- between current-carrying parts and metal parts 500 V
of the luminaire ..................................................... :
P
Other than SELV:
N/A
- between live parts of different polarity................ : 1480
N/A
- between live parts and mounting surface........... : 3710
N/A
- between live parts and metal parts..................... : 1480
N/A
- between live parts of different polarity through
action of a switch .................................................. :
N/A
1.14 (10.3)
Leakage current (mA) ........................................... : 0,01
P
1.15 (13)
RESISTANCE TO HEAT, FIRE AND TRACKING
P
1.15 (13.2.1)
Ball-pressure test:
P
- part tested; temperature (°C).............................. : Housing, 75
P
- part tested; temperature (°C).............................. : Approved terminal block
P
1.15 (13.3.1)
1.15 (13.3.2)
Needle flame test (10 s):
N/A
- part tested........................................................... : -
N/A
- part tested........................................................... : -
N/A
Glow-wire test (650°C):
P
- part tested........................................................... : Housing
P
- part tested........................................................... : -
N/A
page 22 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
1.15 (13.4.1)
Tracking test: part tested ...................................... : -
Verdict
N/A
page 23 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 1: components
object/part No.
code manufacturer/
trademark
type/model
technical data
standard
mark(s) of
conformity
See in first part
The codes above have the following meaning:
A
- The component is replaceable with another one, also certified, with equivalent characteristics
B
- The component is replaceable if authorised by the test house
C
- Integrated component tested together with the appliance
D
- Alternative component
page 24 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
IEC/EN 60598-2-1
Clause
Requirement + Test
Result - Remark
Verdict
ANNEX 2: temperature measurements, thermal tests of Section 12
Type reference .....................................................: See on page 2

Lamp used............................................................: LED MR-16

Lamp control gear used .......................................: -

Mounting position of luminaire .............................: horizontal axis

Supply wattage (W)..............................................: 1

Supply current (A) ................................................: -

Calculated power factor .......................................: 1,06

Table: measured temperatures corrected for ta = 45 °C:
- abnormal operating mode ..................................: -

- test 1: rated voltage ...........................................: -

1,06x12 V = 12,72 V
- test 2: 1,06 times rated voltage or 1,05 times
rated wattage........................................................:

- test 3: Load on wiring to socket-outlet,
1,06 times voltage or 1,05 times wattage ............:

- test 4: 1,1 times rated voltage or 1,05 times
rated wattage........................................................:

Through wiring or looping-in wiring loaded by a
current of A during the test ..................................:

Clause 12.4 – normal
temperature (°C) of part
Clause 12.5 – abnormal
test 1
test 2
test 3
limit
test 4
Lampholder
-
48
-
80
-
Internal wires
-
49
-
90
-
Terminal block
-
45
-
85
-
Plastic housing
-
45
-
100
-
Mounting surface
-
44
-
90
-
VENTS 100 Xstar 12
limit
page 25 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
ANNEX 3: screw terminals (part of the luminaire)
(14)
SCREW TERMINALS
(14.2)
Type of terminal....................................................: LTA 12

Rated current (A)..................................................: -

1
P
(14.3.2.1)
One or more conductors
(14.3.2.2)
Special preparation
(14.3.2.3)
Terminal size
P
Cross-sectional area (mm²)..................................: 2,5
P
(14.3.3)
Conductor space (mm).........................................: 3
P
(14.4)
Mechanical tests
(14.4.1)
Minimum distance
(14.4.2)
Cannot slip out
P
(14.4.3)
Special preparation
P
(14.4.4)
Nominal diameter of thread (metric ISO thread)
P
External wiring
P
No soft metal
P
(14.4.5)
Corrosion
P
(14.4.6)
Nominal diameter of thread (mm) ........................: 2,9
P
Torque (Nm) .........................................................: 0,5
P
Between metal surfaces
P
(14.4.7)
(14.4.8)
N/A
N/A
Lug terminal
N/A
Mantle terminal
N/A
Pull test; pull (N) ...................................................: 50
P
Without undue damage
P
page 26 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
ANNEX 4: screwless terminals (part of the luminaire)
Verdict
N/A
(15)
SCREWLESS TERMINALS
(15.2)
Type of terminal....................................................: -

Rated current (A)..................................................: -

(15.3.1)
Material
N/A
(15.3.2)
Clamping
N/A
(15.3.3)
Stop
N/A
(15.3.4)
Unprepared conductors
N/A
(15.3.5)
Pressure on insulating material
N/A
(15.3.6)
Clear connection method
N/A
(15.3.7)
Clamping independently
N/A
(15.3.8)
Fixed in position
N/A
(15.3.10)
Conductor size
N/A
Type of conductor
N/A
(15.5.1)
Terminals internal wiring
N/A
(15.5.1.1)
Pull test spring-type terminals (4 N,
4 samples)….:
N/A
(15.5.1.2)
Pull test pin or tab terminals (4 N,
4 samples)……:
N/A
Insertion force not exceeding 50 N
N/A
(15.5.2)
Permanent connections: pull-off test (20 N)
N/A
(15.6)
Electrical tests
(15.7)
Voltage drop (mV) after 1 h (4 samples) ..............: -
N/A
Voltage drop of two inseparable joints
N/A
Number of cycles .................................................: -

Voltage drop (mV) after 10th alt. 25th cycle
(4 samples)...........................................................:
N/A
Voltage drop (mV) after 50th alt. 100th cycle
(4 samples)...........................................................:
N/A
After ageing, voltage drop (mV) after 10th alt.
25th cycle (4 samples) .........................................:
N/A
After ageing, voltage drop (mV) after 50th alt.
100th cycle (4 samples) .......................................:
N/A
Terminals external wiring
N/A
page 27 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
(15.8.1)
(15.9)
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
Terminal size and rating
N/A
Pull test spring-type terminals or welded
connections (4 samples); pull (N) ........................:
N/A
Pull test pin or tab terminals (4 samples);
pull (N) .................................................................:
N/A
Contact resistance test
N/A
Voltage drop (mV) after 1 h
N/A
terminal
1
2
3
4
5
6
7
8
9
10
voltage drop (mV)
Voltage drop of two inseparable joints
Voltage drop after 10th alt. 25th cycle
Max. allowed voltage drop (mV) ................ : terminal
1
2
3
4
5

6
7
8
9
10
voltage drop (mV)
Voltage drop after 50th alt. 100th cycle
Max. allowed voltage drop (mV) ................ : terminal
1
2
3
4
5

6
7
8
9
10
voltage drop (mV)
Continued ageing: voltage drop after 10th alt. 25th cycle
Max. allowed voltage drop (mV) ................ : terminal
1
2
3
4
5

6
7
8
9
10
voltage drop (mV)
Continued ageing: voltage drop after 50th alt. 100th cycle
Max. allowed voltage drop (mV) ................ : terminal
1
2
3
4
5

6
7
8
voltage drop (mV)
ANNEX 5: National Differences for (country name) or Group Differences
9
10
page 28 of 28
www.tuv.com
Report No.: 28207876 001
Attachment 2
Clause
IEC/EN 60598-2-1
Requirement + Test
Result - Remark
Verdict
CENELEC COMMON MODIFICATIONS (EN)
1.5 (3)
MARKING
N/A
1.5 (3.3.101)
Adequate warning on the package
N/A
1.10 (5)
EXTERNAL AND INTERNAL WIRING
P
1.10 (5.2.1)
Connecting leads
P
- without a means for connection to the supply
P
- terminal block specified
N/A
- relevant information provided
N/A
- compliance with 4.6, 4.7.1, 4.7.2, 4.10.1, 11.2,
12 and 13.2 of Part 1
P
1.10 (5.2.2)
Cables equal to HD21 S2 or HD22 S2
N/A
ZB
ANNEX ZB, SPECIAL NATIONAL CONDITIONS (EN)
N/A
(3.3)
DK: power supply cord with label
N/A
IT: warning label on Class 0 luminaire
N/A
(4.5.1)
DK: socket-outlets
N/A
(5.2.1)
CY, DK, FI, SE, GB: type of plug
N/A
ZC
ANNEX ZC, NATIONAL DEVIATIONS (EN)
N/A
(4 & 5)
FR: Shuttered socket-outlets 10/16A
N/A
(13.3)
DK: Needle flame test during 30 s
N/A
(13.3)
GB: Requirements according to United Kingdom
Building Regulation
N/A
(13.3.2)
FR: Glow-wire test 850°C alt. 750°C for
luminaires in premises open to public or 960°C
for luminaires in emergency exits
N/A
Mér eszköz lista
Measuring equipment list
www.tuv.com
Jegyz könyv szám / Test report No. 28207876 001
Melléklet 3 / Attachment 3
Mér eszköz
Measuring equipment
Gyártó
Manufacturer
Típus
Type
Oldal / Page 1 / 1
Leltári sz. / széria sz. Köv. kalibráció
Inventory / Serial No. Next calibration
Dielectric strength tester
Kikusui
TOS 5050
211/23246/2005
07. 2010.
Ohm meter
Ganz
DKE
0570632051
10. 2010.
Leakage current measurer
HIOKI
3156
2110/718
06. 2010.
Wattmeter
Norma
D 1150
023066
07. 2010.
Data acquisition system
Fluke
HELIOS I 2289 A
023061
10. 2010.
Torque screwdriver
Facom
A301A
60044
10.2010.
Glow wire test equipment
PTL
T 03.34
22196
05.2010.
Ball-pressure test device
MEEI KFT
-
2071/002
04.2010.
Test probe B of IEC 61032
MEEI KFT
-
023031
07.2010.
Test probe 13 of IEC 61032 MEEI KFT
-
023031
07.2010.
Caliper
Mitutoyo
CD-15B
0556014008
05.2010.
Spring hammer
NEMKO
0,5Nm
22869
07.2010.
Gauge pot
-
-
230/029
11.2010.
Stopwatch
HIDEKI
-
2041/016
09.2010.
Spring type force meter
Erichsen
0-50N
0570550051
07.2010.
Insulation resistance tester
Ganz
XS- 1000
0578065009
09.2010.
Megjegyzés / Remark: –
F 27-X1_1_0
Page 1/1
2007.07.10-t l
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement