Erico DYNASPHERE MKIV Installation Instructions
PDF
Download
Document
Advertisement
Advertisement
INSTRUCTION SHEET ERICO® DYNASPHERE MKIV Installation Instructions for 5m Aluminum Guyed Mast Final position of the FRP Mast and the ERICO DYNASPHERE ERICO DYNASPHERE (ERICO® Part # D/SMKIV-SS) ERICO® ERICORE Downconductor with factory fitted upper termination FRP Upper Support Mast 2M (ERICO Part # FRP2MBLACK) In Line Coupler (ERICO Part # ILCOUPL) Guy Wire Kit 4M (ERICO Part # GUYKIT4M) 1 Placement 6.6FT [2M] ЗМ Aluminum Mast (ERICO Part # MBMAST3M) For mast base refer to Detail ”B” Conductive Saddle for ERICO ERICORE Cable (ERICO Part # CONSAD/E2/5) Self Tapping Screws (ERICO Part # CONSAD—FX) ,_9-8FT [3M] ERICO® CADWELD® Connection or mechanical connection Detail "A" Lightning Event Counter (ERICO Part # LECIV) ERICO ERICORE Downconductor Crow’s Foot ea [AR $ -7/ Ground Inspection Well Bond to the existing building ground system with ERICO CADWELD Connection SA Minimum 2/0 (50mm?) Conductor Minimum 5/8” x 8’ [16mm x 2.4M] (3 x 20FT [6.1M] Length) ground rod in four locations Enclosed in GEM material Suggested three radial grounding system for each downconductor: The grounding system shown in the detail is a suggested layout. Each radial consists of a trench approximately 1.5FT [0.45M] deep. 3 x 20FT [6.1M] of 2/0 conductor is laid in the trench and is connected to ground rods. The conductor in each trench is encased in GEM material. Ground rods must extend 10FT [3M] below ground level. Note: This is one of several alternative installation methods. Refer to ERICO instruction print IP79157 for more details. ERICO is not responsible for field installaion of lightning protection systems. The installation integrity of each system should be approved and stamped (ERICO Part # LECIV) y | by a structural professional engineer. Conductive Saddle for ERICO ERICORE Cable D | l "В" Refer to installation manual for alternate locations. Mast Base (ERICO Part # CONSAD/E2/5) Self Tapping Screws (ERICO Part # CONSAD—FX) 9.00 [228.6mm] 4.50 [114.3mm] Every 3.3FT [1M] Typical WN ON o Every 3.3FT [1M] Typical Lightning Event Count [I ightning Event Counter ERICORE Downconductor (Minimum Bending Radius 40” [0.5M]) 0.25 [6.4mm] | For complete Grounding Welds System refer to Detail ”A” \ £ || || A 4.50 [114.3mm] 9.00 [228.6mm] a Lower Termination Kit (ERICO Part # ERICORE/LTKIT/A) 4 Holes Ground Inspection Well $0.50 [12.7тт] _ (©) -® (ERICO Part # T416B) Ground Rod —_ WARNING: 1. ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at www.erico.com and from your ERICO customer service representative. 2. ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 3. All instructions must be completely followed to ensure proper and safe installation and performance. 4. Improper installation, misuse, misapplication or other failure to completely follow ERICO’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death. SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation. ® 1 OF 1 ©2006,2014 ERICO International Corporation ERICO TECHNICAL SUPPORT: www.erico.com IP7996_B ">

Public link updated
The public link to your chat has been updated.
Advertisement