Datasheet - Mouser Electronics
®
Keithley’s Series 2400 Source Measure Unit (SMU) Instruments
are designed specifically for test applications that demand tightly
coupled sourcing and measurement. All SourceMeter models provide precision voltage and current sourcing as well as measurement capabilities. Each SourceMeter SMU instrument is both
a highly stable DC power source and a true instrument-grade
6½-digit multimeter. The power source characteristics include
low noise, precision, and readback. The multimeter capabilities
include high repeatability and low noise. The result is a compact,
single-channel, DC parametric tester. In operation, these instruments can act as a voltage source, a current source, a voltage
meter, a current meter, and an ohmmeter. Manufacturers of
components and modules for the communications, semiconductor, computer, automotive, and medical industries will find the
SourceMeter SMU instruments invaluable for a wide range of
characterization and production test applications.
• Five instruments in one
(IV Source, IVR Measure)
• Seven models: 20–100W DC,
1000W pulsed, 1100V to 1µV,
10A to 10pA
• Source and sink (4-quadrant)
operation
• 0.012% basic measure accuracy
with 6½-digit resolution
• 2-, 4-, and 6-wire remote
V-source and measure sensing
• 1700 readings/second at
4½ digits via GPIB
• Pass/Fail comparator for fast
sorting/binning
• Available high speed sense lead
contact check function
SMU INSTRUMENTS
SourceMeter SMU Instruments
• Programmable DIO port for
automation/handler/prober
control (except Model 2401)
• Standard SCPI GPIB, RS-232 and
Keithley Trigger Link interfaces
• Keithley LabTracer 2.0 I-V curve
tracing application software
(download)
Advantages of a Tightly Integrated Instrument
By linking source and measurement circuitry in a single unit,
these instruments offer a variety of advantages over systems
configured with separate source and measurement instruments.
For example, they minimize the time required for test station
development, setup, and maintenance, while lowering the overall
cost of system ownership. They simplify the test process itself
by eliminating many of the complex synchronization and connection issues associated with using
multiple instruments. And, their compact half-rack size conserves precious “real estate” in the test
rack or bench.
Power of Five Instruments in One (IV Source, IVR Measure)
The tightly coupled nature of a SourceMeter SMU instrument provides many advantages over solutions configured from separate instruments, such as a precision power supply and a digital multimeter. For example, it provides faster test times by reducing GPIB traffic and simplifies the remote programming interface. It also protects the device under test from damage due to accidental overloads,
thermal runaway, etc. Both the current and voltage source are programmable with readback to help
maximize device measurement integrity. If the readback reaches a programmed compliance limit,
then the source is clamped at the limit, providing fault protection.
ACCESSORIES AVAILABLE
TEST LEADS
1754
5804
5805
5808
5809
8607
CA-18-1
AND PROBES
2-Wire Universal 10-Piece Test Lead Kit
Kelvin (4-Wire) Universal 10-Piece Test Lead Kit
Kelvin (4-Wire) Spring-Loaded Probes
Low Cost Single-pin Kelvin Probe Set
Low Cost Kelvin Clip Lead Set
2-Wire, 1000V Banana Cables, 1m (3.3 ft)
Shielded Dual Banana Cable, 1.2m (4 ft)
SWITCHING
7001
7002
7019-C
7053
HARDWARE
Two-Slot Switch System
Ten-Slot Switch System
6-Wire Ohms Switch Card
High-Current Switch Card
CABLES/ADAPTERS
7007-1
Shielded GPIB Cable, 1m (3.3 ft)
7007-2
Shielded GPIB Cable, 2m (6.6 ft)
7009-5
RS-232 Cable
8620
Shorting Plug
Communication Interface
KPCI-488LPA IEEE-488 Interface/Controller for the PCI Bus
KUSB-488B
IEEE-488 USB-to-GPIB Interface Adapter
Triggering and Control
2499-DIGIO Digital I/O Expander Assembly
(not for Model 2401)
8501-1
Trigger Link Cable, DIN-to-DIN, 1m (3.3 ft)
8501-2
Trigger Link Cable, DIN-to-DIN, 2m (6.6 ft)
8502
Trigger Link to BNC Breakout Box
8503
Trigger Link Cable, DIN-to-Dual BNC, 1m (3.3 ft)
8505
Male to 2-Female Y-DIN Cable for Trigger Link
RACK MOUNT KITS
4288-1
Single Fixed Rack Mount Kit
4288-2
Dual Fixed Rack Mount Kit
4288-4
Dual Fixed Rack Mount Kit
4288-5
Shelf Type Side by Side Rack Mounting Kit
4288-9
Dual Fixed Rack Mounting Kit
Software
LabTracer 2.0 Curve Tracing Software (downloadable)
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
Tightly coupled precision sourcing and measurement
Tightly coupled precision sourcing and measurement
Series 2400
Tightly coupled precision sourcing and measurement
2400
200V, 1A, 20W
SourceMeter SMU
Instrument
2400-C 200V, 1A, 20W
SourceMeter SMU
Instrument with Contact
Check
2401 20V, 1A, 20W SourceMeter
SMU Instrument
2410 1100V, 1A, 20W
SourceMeter SMU
Instrument
2410-C 1100V, 1A, 20W
SourceMeter SMU
Instrument with Contact
Check
2420 60V, 3A, 60W SourceMeter
SMU Instrument
2420-C 60V, 3A, 60W SourceMeter
SMU Instrument with
Contact Check
2425 100V, 3A, 100W
SourceMeter SMU
Instrument
2425-C 100V, 3A, 100W
SourceMeter SMU
Instrument with Contact
Check
2430 100V, 10A, 1000W
Pulse Mode SourceMeter
SMU Instrument
2430-C 100V, 10A, 1000W
Pulse Mode SourceMeter
SMU Instrument with
Contact Check
2440 40V, 5A, 50W SourceMeter
SMU Instrument
2440-C 40V, 5A, 50W SourceMeter
SMU Instrument with
Contact Check
Accessories Supplied
Model 8605 Test Leads
LabVIEW Software Driver
­(downloadable)
LabTracer Software
­(downloadable)
®
I-V Characteristics
All SourceMeter SMU instruments provide four-quadrant operation. In the first and third quadrants
they o­ perate as a source, delivering power to a load. In the second and fourth quadrants they operate as a sink, d­ issipating power internally. Voltage, current, and resistance can be measured during
source or sink ­operation.
Imeter
Local
IN/OUT HI
Remote
SENSE HI
Imeter/Compliance
Isource
Local
IN/OUT HI
Remote
SENSE HI
Remote
SENSE LO
Local
IN/OUT LO
Vmeter
Vsource
DUT
DUT
Feedback to
Adjust Vsource
Vmeter/Compliance
Remote
SENSE LO
Local
IN/OUT LO
Source I–Measure V, I, or W configuration
Source V–Measure I, V, or W configuration
Series 2400 SourceMeter SMU Instruments
+1A
Model 2400
SourceMeter
SMU Instrument
–200V
+100mA
–20V
+20V
2400
only
+1A
Model 2401
Low-Voltage
SourceMeter
SMU Instrument
+200V
–200V
+100mA
–20V
+20V
2400
only
–100mA
–100mA
Duty cycle limited
Duty cycle limited
–1A
–1A
Model 2410
High-Voltage
SourceMeter
SMU Instrument
Model 2420
3A SourceMeter
SMU Instrument
+1A
+20V
Model 2425
100W SourceMeter
SMU Instrument
+200V +1100V
–60V
–20mA
Model 2430
1kW Pulse Mode
SourceMeter
SMU Instrument
+20V
+100mA
+60V
–100V
+10A
+3A
+1A
–3A
Duty cycle
limited
–3A
3A
100mA
–40V
–10V
+10V
+40V
–100mA
–100mA
–1A
–1A
–3A
–3A
Duty cycle limited
Pulse mode only
–10A
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
Duty cycle
limited
5A
Model 2440
5A SourceMeter
SMU Instrument
1A
+20 +60 +100V
+100V
–1A
–1A
Duty cycle
limited
+20 +60
–100mA
+100mA
–100V –60 –20
–60 –20
–100mA
–100mA
–1A
–20V
+3A
+1A
+100mA
+20mA
–20V
+3A
+1A
+200mA
–1100V –200V
+200V
Tightly coupled precision sourcing and measurement
Ordering Information
SourceMeter SMU Instruments
–5A
Duty cycle limited
SMU INSTRUMENTS
Series 2400
SourceMeter SMU Instruments
®
Automation for Speed
A SourceMeter SMU instrument streamlines production testing. It sources voltage or current while
making measurements without needing to change connections. It is designed for reliable operation
in non-stop production environments. To provide the throughput demanded by production applications, the SourceMeter SMU instrument offers many built-in features that allow it to run complex test
sequences without computer control or GPIB communications slowing things down.
Standard and Custom Sweeps
Sweep solutions greatly accelerate testing with
automation hooks. Three basic sweep waveforms
are provided that can be programmed for singleevent or continuous operation. They are ideal for
I/V, I/R, V/I, and V/R characterization.
• Linear Staircase Sweep: Moves from the start
level to the stop level in equal linear steps
• Logarithmic Staircase Sweep: Done on a
log scale with a specified number of steps
per decade
• Custom Sweep: Allows construction of
special sweeps by specifying the number of
measurement points and the source level at
each point
• Up to 1700 readings/second at 4½ digits to
the GPIB bus
• 5000 readings can be stored in the nonvolatile buffer memory
Stop
Start
Bias
Bias
Linear staircase sweep
Stop
Start
Bias
Bias
Logarithmic staircase sweep
Start
Stop
User
defined
steps
Built-In Test Sequencer
Bias
Bias
(Source Memory List)
The Source Memory list provides faster and
Custom sweep
easier testing by allowing you to setup and
execute up to 100 different tests that run without
PC intervention.
• Stores up to 100 instrument configurations, each containing source settings, measurement
­settings, pass/fail criteria, etc.
• Pass/fail limit test as fast as 500µs per point
• Onboard comparator eliminates the delay caused when sending data to the computer for analysis
• Built-in, user definable math functions to calculate derived parameters
Typical Applications
Devices:
• Discrete semiconductor devices
• Passive devices
• Transient suppression devices
• ICs, RFICs, MMICs
• Laser diodes, laser diode
modules, LEDs, photodetectors
• Circuit protection devices: TVS,
MOV, Fuses, etc.
• Airbags
• Connectors, switches, relays
• High brightness LEDs
(DC and pulse)
Tests:
• Leakage
• Low voltage/resistances
• LIV
• IDDQ
• I-V characterization
• Isolation and trace resistance
• Temperature coefficient
• Forward voltage, reverse
breakdown, leakage current
• DC parametric test
• DC power source
• HIPOT
• Photovoltaic cell efficiency
(source and sink)
• Dielectric withstanding
Example Test Sequence
SMU INSTRUMENTS
I
VF2
IR
VF1
Test 2
Test 1
Test 3
V
Test
Pass/Fail Test
If Passes Test
Test 1
Check V F1 at
100mA against
pass/fail limits
Go to Test 2
Test 2
Check V F2 at 1A
against pass/fail
limits
Go to Test 3
Test 3
Check leakage
­current at –500V
and test against
pass/fail limits
1. Bin part to good bin
2. Transmit readings to
computer while handler
is placing new part
3. Return to Test 1
If Fails Test
1. Bin part to bad bin
2. Transmit data to
computer while
handler is placing
new part
3. Return to Test 1
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
Tightly coupled precision sourcing and measurement
Tightly coupled precision sourcing and measurement
Series 2400
SourceMeter SMU Instruments
®
The digital I/O interface is available on all Series 2400 SoourceMeter
instruments except the Model 2401.
Trigger Link Interface
All SourceMeter SMU instruments include Keithley’s unique Trigger Link
interface which provides high-speed, seamless communications with many
of Keithley’s other instruments. For example, use the Trigger Link interface
to connect a SourceMeter SMU instrument with a Series 7000 Switching
System for a complete multi-point test solution. With Trigger Link, the
Series 7000 Switching Systems can be controlled by a SourceMeter SMU
instrument during a high-speed test sequence independent of a computer
and GPIB.
Optional Contact Check Function
The Contact Check function makes it simple to verify good connections
quickly and easily before an automated test sequence begins. This eliminates measurement errors and false product failures associated with contact fatigue, breakage, contamination, loose or broken connection, relay
failures, etc. Some capabilities of this function are:
• 350µs verification and notification process time
• The output of the SourceMeter SMU instrument is automatically shut
off after a fault and is not re-activated until good contact is verified,
protecting the device under test from damage and the operator from
potential safety h­ azards.
• 3 pass/fail threshold values: 2W, 15W, and 50W
• No energy passes through the device under test during the operation.
• Enabled either from the front panel or remotely over the GPIB
• 3 fault notification methods
• Allows users to configure and plot data easily from Series 2400
SourceMeter SMU instruments, making characterization of two, three,
and four terminal devices a snap.
+
GUARD
GUARD SENSE
Imeter
IN/OUT HI
SENSE HI
DUT
R2
Isource
Vmeter
R1
R3
SENSE LO
IN/OUT LO
6-Wire Ohms Circuit. All test current flows through R1 because the
high current guard drives the voltage across R2 to 0V.
Pass
350µs
Contact Check
IN/OUT HI
Fail
(optional)
SENSE LO
Pass
IN/OUT LO
Contact check option for 4-wire or 6-wire applications
Free LabTracer 2.0 device characterization software (downloadable)
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
SMU INSTRUMENTS
Vmeter
• Locks out parallel current paths when measuring resistor networks or
hybrid c­ ircuits to isolate the component under test.
GUARD SENSE
SENSE HI
V or I
Source
• Uses guard and guard sense leads in addition to the 4-wire sense and
source leads.
GUARD
-
Imeter
Unique 6-Wire Ohms Technique
SourceMeter SMU instruments can make standard 4-wire, split Kelvin, and
6-wire, guarded ohms measurements and can be configured for either the
constant current or constant voltage method. The 6-wire ohms technique:
Tightly coupled precision sourcing and measurement
Digital I/O Interface
The digital I/O interface can link a SourceMeter SMU instrument to many
popular component handlers, including Aetrium, Aeco, and Robotronics.
Other capabilities of the interface include:
• Tight systems integration for applications such as binning and sorting
• Built-in component handler interface
• Start of test and end of test signals
• 5V, 300mA power supply
• Optional expander accessory (Model 2499-DIGIO) adds 16 digital I/O lines
+
Tightly coupled precision sourcing and measurement
Series 2400
Series 2400
SourceMeter SMU Instruments
®
Voltage Accuracy (Local or Remote Sense)
Series 2400 condensed specifications
2400, 2400-C,
2401
2410, 2410-C
2420, 2420-C
2425, 2425-C
2430, 2430-C
2440, 2440-C
Range
200.000mV
2.00000V
20.0000V
200.000V*
200.000mV
2.00000V
20.0000V
1000.00V
200.000mV
2.00000V
20.0000V
60.0000V
200.000mV
2.00000V
20.0000V
100.0000 V
200.000mV
2.00000V
20.0000V
100.0000 V
200.000mV
2.00000V
10.0000V
40.0000V
Programming
Resolution
5µV
50µV
500µV
5mV
5µV
50µV
500µV
50mV
5µV
50µV
500µV
1.5mV
5 µV
50µV
500µV
2.5mV
5µV
50µV
500µV
2.5mV
5µV
50µV
500µV
5mV
Default
Measurement
Resolution
1 µV
10 µV
100 µV
1 mV
1 µV
10 µV
100 µV
10 mV
1 µV
10 µV
100 µV
1 mV
1 µV
10 µV
100 µV
1 mV
1 µV
10 µV
100 µV
1 mV
1 µV
10 µV
100 µV
1 mV
Measurement 2, 3, 4
Accuracy (1 Year)
23°C ±5°C
±(% rdg. + volts)
0.012% + 300 µV
0.012% +300 µV
0.015% + 1.5 mV
0.015% + 10 mV
0.012% +300 µV
0.012% +300 µV
0.015% + 1 mV
0.015% + 50 mV
0.012% +300 µV
0.012% +300 µV
0.015% + 1 mV
0.015% + 3 mV
0.012% +300 µV
0.012% +300 µV
0.015% + 1 mV
0.015% + 5 mV
0.012% +300 µV
0.012% +300 µV
0.015% + 1 mV
0.015% + 5 mV
0.012% +300 µV
0.012% +300 µV
0.015% + 750 µV
0.015% + 3 mV
Output Slew Rate
(±30%)
Source/Sink Limit
0.08 V/µs
0.5 V/µs
0.15 V/µs
0.5 V/µs
0.08 V/µs
0.14 V/µs
0.08 V/µs
0.25 V/µs
±21 V @ ±1.05 A
±210 V @ ±105 mA*
±21 V @ ±1.05 A
±1100 V @ ±21 mA
±21 V @ ±3.15 A
±63 V @ ±1.05 A
±21 V @ ±3.15 A
±105 V @ ±1.05 A
±105 V @ ±1.05 A
0.08 V/µs
0.25 V/µs
0.08 V/µs
0.25 V/µs
±105 V @ ±10.5 A
(pulse mode only)
±10.5 V @ ±5.25 A
±42 V @ ±1.05 A
*Not available on Model 2401.
Temperature Coefficient (0°–18°C and 28°–50°C): ±(0.15 × accuracy specification)/°C.
Voltage Regulation: Line: 0.01% of range. Load: 0.01% of range + 100µV.
Over Voltage Protection: User selectable values, 5% tolerance. Factory default = none.
Current Limit: Bipolar current limit (compliance) set with single value. Min. 0.1% of range.
Overshoot: <0.1% typical (full scale step, resistive load, 10mA range).
SMU INSTRUMENTS
ADDITIONAL SOURCE SPECIFICATIONS (All Models)
TRANSIENT RESPONSE TIME: 30µs minimum for the output to recover to its spec. following a
step change in load.
COMMAND PROCESSING TIME: Maximum time required for the output to begin to change
following the receipt of :SOURce:VOLTage|CURRent <nrf> command. Autorange On: 10ms.
Autorange Off: 7ms.
OUTPUT SETTLING TIME: Time required to reach 0.1% of final value after command is processed. 100µs typical. Resistive load. 10µA to 100mA range.
DC FLOATING VOLTAGE: Output can be floated up to ±250VDC (Model 2440 ±40VDC) from
chassis ground.
REMOTE SENSE: Up to 1V drop per load lead.
COMPLIANCE ACCURACY: Add 0.3% of range and ±0.02% of reading to base specification.
OVER TEMPERATURE PROTECTION: Internally sensed temperature overload puts unit in
standby mode.
RANGE CHANGE OVERSHOOT: Overshoot into a fully resistive 100kW load, 10Hz to 1MHz BW,
adjacent ranges: 100mV typical, except 20V/200V (20V/60V on Model 2420), 20V/100V on Model
2425 and 2430, range boundary, and Model 2440.
MINIMUM COMPLIANCE VALUE: 0.1% of range.
Additional Pulse Mode Source Specifications
(2430 and 2430-C only)
Maximum Duty Cycle: 8%, hardware limited, 10A range only. All other ranges 100%.
Maximum Pulse Width: 5ms from 90% rising to 90% falling edge, 2.5ms 10A range.
Minimum Pulse Width: 150µs.
Minimum Pulse Resolution: 50µs typical, 70µs max., limited by system ­jitter.
Source Accuracy: Determined by settling time and source range specifications.
Output Settling Time 0.1%:
800µs typ., source I = 10A into 10W, limited by voltage slew rate.
500µs typ., source I = 10A into 1W, limited by voltage slew rate.
Output Slew Rate:
Voltage (10W load): 0.25V/µs ±30% on 100V range. 0.08V/µs ±30% on 20V range, 10A range.
Current (0W load): 0.25A/µs ±30% on 100V range. 0.08A/µs ±30% on 20V range, 10A range.
NOTES
1. 2400, 2401, 2410 Only: Specifications valid for continuous output currents below 105mA. For operation above
105mA continuous for >1 minute, derate accuracy 10%/35mA above 105mA.
2. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A
ranges, add 0.05%. For 0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges, add
0.5%.
3. Accuracies apply to 2- or 4-wire mode when properly zeroed.
4. In pulse mode, limited to 0.1 PLC measurement.
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
Series 2400 condensed specifications
Model
Source1
Accuracy (1 Year)
23°C ±5°C
±(% rdg. + volts)
0.02% + 600 µV
0.02% + 600 µV
0.02% + 2.4 mV
0.02% + 24 mV
0.02% + 600 µV
0.02% + 600 µV
0.02% + 2.4 mV
0.02% + 100 mV
0.02% + 600 µV
0.02% + 600 µV
0.02% + 2.4 mV
0.02% + 7.2 mV
0.02% + 600 µV
0.02% + 600 µV
0.02% + 2.4 mV
0.02% + 12 mV
0.02% + 600 µV
0.02% + 600 µV
0.02% + 2.4 mV
0.02% + 12 mV
0.02% + 600 µV
0.02% + 600 µV
0.02% + 1.2 mV
0.02% + 4.8 mV
Series 2400
SourceMeter SMU Instruments
®
Current Accuracy (Local or Remote Sense)
2410, 2410-C
2420, 2420-C
2425, 2425-C
2430, 2430-C
2440, 2440-C
Programming
Resolution
50 pA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
50 pA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
50 µA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
50 µA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
500 µA
500 µA
500 pA
5 nA
50 nA
500 nA
5 µA
50 µA
50 µA
Temperature Coefficient (0°–18°C and 28°–50°C): ±(0.15 × accuracy specification)/°C.
CURRENT Regulation: Line: 0.01% of range. Load: 0.01% of range (except Model 2440
5A range 0.05%) + 100pA.
Voltage LIMIT: Bipolar voltage limit (compliance) set with single value. Min. 0.1% of range.
OVERSHOOT: <0.1% typical (1mA step, RL = 10kW, 20V range for Model 2400, 2401, 2410, 2420,
2425, 2430), (10V range for Model 2440).
Contact Check Specifications (requires -C version)
(Not available for Model 2401)
Speed: 350µs for verification and notification.
Contact Check:
2 W15 W50 W
No contact check failure
<1.00 W<13.5 W<47.5 W
Always contact check failure
>3.00 W>16.5 W>52.5 W
Default Measurement
Resolution
10 pA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
10 pA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
10 µA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
10 µA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
10 µA
10 µA
100 pA
1 nA
10 nA
100 nA
1 µA
10 µA
10 µA
Source/Sink Limit
±1.05A @ ±21 V
±105 mA @ ±210 V 8
±1.05A @ ±21 V
±21 mA @ ±1100 V
±3.15A @ ±21 V
±1.05 A @ ±63 V
Series 2400 condensed specifications
2400, 2400-C,
2401
Range
1.00000 µA
10.0000 µA
100.000 µA
1.00000 mA
10.0000 mA
100.000 mA
1.00000 A 2
1.00000 µA
10.0000 µA
100.000 µA
1.00000 mA
20.0000 mA
100.000 mA
1.00000 A 2
10.0000 µA
100.000 µA
1.00000 mA
10.0000 mA
100.000 mA
1.00000 A 2
3.00000 A 2
10.0000 µA
100.000 µA
1.00000 mA
10.0000 mA
100.000 mA
1.00000 A 2
3.00000 A 2
10.0000 µA
100.000 µA
1.00000 mA
10.0000 mA
100.000 mA
1.00000 A
3.00000 A 2
10.00000 A4
10.0000 µA
100.000 µA
1.00000 mA
10.0000 mA
100.000 mA
1.00000 A
5.00000 A
Measurement 5, 6, 7
Accuracy (1 Year)
23°C ±5°C
±(% rdg. + amps)
0.029% + 300 pA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 600 nA
0.055% + 6 µA
0.22 % + 570 µA
0.029% + 300 pA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 1.2 µA
0.055% + 6 µA
0.22 % + 570 µA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 600 nA
0.055% + 6 µA
0.066% + 570 µA
0.052% + 1.71 mA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 600 nA
0.055% + 6 µA
0.060% + 570 µA
0.052% + 1.71 mA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 600 nA
0.055% + 6 µA
0.060% + 570 µA
0.052% + 1.71 mA
0.082% + 1.71 mA
0.027% + 700 pA
0.025% + 6 nA
0.027% + 60 nA
0.035% + 600 nA
0.055% + 6 µA
0.060% + 570 µA
0.10 % + 3.42 mA
±3.15A @ ±21 V
±1.05 A @ ±105 V
±1.05A @ ±105 V
±10.5 A @ ±105 V
(pulse mode only)
±5.25A @ ±10.5 V
±1.05 A @ ±42 V
NOTES
1. 2400, 2401, 2410 Only: Specifications valid for continuous output currents below 105mA. For operation above
105mA continuous for >1 minute, derate accuracy 10%/35mA above 105mA.
2. Full operation (1A) regardless of load to 30°C (50°C for Model 2420 and 2440). Above 30°C (50°C for Model
2420 and 2440) ambient, derate 35mA/°C and prorate 35mA/W load. 4-wire mode. For current sink operation
on 1A, 3A, or 5A ranges, maximum continuous power is limited to approximately 1/2 rated power or less,
depending on current, up to 30°C ambient. See power equations in the User’s Manual to calculate allowable
duty cycle for specific conditions.
3. For sink mode, 1µA to 100mA range, accuracy is:
Model 2400, 2401: ±(0.15% + offset*4). Models 2410, 2420, 2425, 2430, 2440: ±(0.5% + offset*3).
For 1A range, accuracy is:
Model 2400, 2401: ±(1.5% + offset*8). Models 2410, 2420, 2425, 2430, 2440: ±(1.5% + offset*3).
4. 10A range only in pulse mode. Limited to 2.5ms pulse width maximum. 10% duty cycle maximum.
5. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A
ranges, add 0.05%. For 0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges,
add 0.5%.
6. Accuracies apply to 2- or 4-wire mode when properly zeroed.
7. In pulse mode, limited to 0.1 PLC measurement.
8. Model 2400 and 2400-C only.
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
SMU INSTRUMENTS
Series 2400 condensed specifications
Model
Source 1, 3
Accuracy
(1 Year)
23°C ±5°C
±(% rdg. + amps)
0.035% + 600 pA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 2 µA
0.066% + 20 µA
0.27 % + 900 µA
0.035% + 600 pA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 4 µA
0.066% + 20 µA
0.27 % + 900 µA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 2 µA
0.066% + 20 µA
0.067% + 900 µA
0.059% + 2.7 mA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 2 µA
0.066% + 20 µA
0.067% + 900 µA
0.059% + 2.8 mA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 2 µA
0.066% + 20 µA
0.067% + 900 µA
0.059% + 2.8 mA
0.089% + 5.9 mA
0.033% + 2 nA
0.031% + 20 nA
0.034% + 200 nA
0.045% + 2 µA
0.066% + 20 µA
0.067% + 900 µA
0.10 % + 5.4 mA
Series 2400
SourceMeter SMU Instruments
®
Range
Default
Resolution
Default Test
Current
2400, 2401, 2410
<0.20000 W3
–
–
Enhanced Accuracy
(23°C ±5°C) 4
1 Year, ±(% rdg. + ohms)
Default Test
Current
2420, 2425,
2430, 2440
2400, 2401
2410
2420, 2425, 2430, 2440
2400, 2401
–
Source I ACC + Meas. VACC
Source I ACC + Meas. VACC
Source I ACC + Meas. VACC
Source I ACC + Meas. VACC
1A
Source I ACC + Meas. VACC
Normal Accuracy (23°C ±5°C)
1 Year, ±(% rdg. + ohms)
2.00000 W3
10µW
–
Source I ACC + Meas VACC
Source I ACC + Meas. VACC
0.17% + 0.0003W
20.0000 W
100µW
100mA
100mA
0.10% + 0.003W
0.11% + 0.006W
0.10% + 0.003 W
0.07% + 0.001
200.000 W
1mW
10mA
10mA
0.08% + 0.03 W
0.09% + 0.1 W
0.08% + 0.03 W
0.05% + 0.01
W
2.00000kW
10mW
1mA
1mA
0.07% + 0.3 W
0.08% + 0.6 W
0.07% + 0.3
W
0.05% + 0.1
W
20.0000kW
W
100mW
100µA
100µA
0.06% + 3
W
0.07% + 6
W
0.06% + 3
W
0.04% + 1
W
200.000kW 1
W
10µA
10µA
0.07% + 30
W
0.07% + 60
W
0.07% + 30
W
0.05% + 10
W
W
2.00000MW6 10
1µA
1µA
0.11% +300
W
0.12% +600
W
0.11% +300
W
0.05% +100
W
20.0000MW7 100W
1µA
1µA
0.11% + 1
kW
0.12% + 2.4 kW
0.11% + 1
kW
0.05% +500
W
200.000MW3
>200.000 MW3
1kW
–
100nA
–
–
–
0.66% + 10 kW
Source I ACC + Meas. VACC
TEMPERATURE COEFFICIENT (0°–18°C and 28°–50°C): ±(0.15 × accuracy
specification)/°C.
Source I Mode, Manual Ohms: Total uncertainty = I source accuracy + V measure accuracy (4-wire remote sense).
Source V Mode, Manual Ohms: Total uncertainty = V source a­ ccuracy + I measure accuracy (4-wire remote sense).
6-wire ohms mode: Available using active ohms guard and guard sense. Max.
Guard Output Current: 50mA (except 1A range). Accuracy is load dependent.
Refer to White Paper no. 2033 for calculation f­ormula.
Guard Output Impedance: <0.1W in ohms mode.
0.66% + 24 kW
Source I ACC + Meas. VACC
Source I ACC + Meas. VACC
Source I ACC + Meas. VACC
0.35% + 5
kW
Source I ACC + Meas. VACC
NOTES
1. Speed = Normal (1 PLC). For 0.1 PLC, add 0.005% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.05%. For
0.01 PLC, add 0.05% of range to offset specifications, except 200mV, 1A, 10A ranges, add 0.5%.
2. Accuracies apply to 2- or 4-wire mode when properly zeroed.
3. Manual ohms only – except 2420, 2425, 2430, 2440 for 2W range and 2400, 2401, or 2410 for 200MW range.
4. Source readback enabled, offset compensation ON. Also available on 2410, 2420, 2425, 2430, and 2440 with similar a­ ccuracy
enhancement.
5. In pulse mode, limited to 0.1 PLC measurement.
6. Except 2440; default test current is 5µA.
7. Except 2440; default test current is 0.5µA.
Services Available
SMU INSTRUMENTS
2400-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2400-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
2401-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2410-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2410-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
2420-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2420-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
2425-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2425-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
2430-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2430-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
2440-3Y-EW
1-year factory warranty extended to 3 years from date of shipment
2440-C-3Y-EW 1-year factory warranty extended to 3 years from date of shipment
C/2400-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2400, 2400-C, 2400-LV*
C/2401-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Model 2401*
C/2410-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2410, 2410-C*
C/2420-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2420, 2420-C*
C/2425-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2425, 2425-C*
C/2430-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2430, 2430-C*
C/2440-3Y-ISO 3 (ISO-17025 accredited) calibrations within 3 years of purchase for Models 2440, 2440-C*
TRN-2400-1-C Course: Unleashing the Power of Your SourceMeter SMU Instrument
*Not available in all countries
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
Series 2400 condensed specifications
Series 2400 condensed specifications
Resistance Measurement Accuracy (Local or Remote Sense)1, 2, 5
Series 2400
SourceMeter SMU Instruments
®
System Speeds
Measurement1
MAXIMUM RANGE CHANGE RATE: 75/second.
MAXIMUM MEASURE AUTORANGE TIME: 40ms (fixed source).2
Fast
IEEE-488.1 Mode
Fast
IEEE-488.2 Mode
Medium
IEEE-488.2 Mode
Normal
IEEE-488.2 Mode
NPLC/Trigger Origin
0.01 / internal
0.01 / external
0.01 / internal
0.01 / external
0.10 / internal
0.10 / external
1.00 / internal
1.00 / external
Source-Measure
To Mem.
To GPIB
1551 (1515)
1369
1018 (990)
1035
1551 (1515)
1000 (900)
1018 (990)
916 (835)
470 (405)
470 (410)
409 (360)
409 (365)
58 (48)
58 (48)
57 (48)
57 (47)
Source-Measure5
Pass/Fail Test4, 5
To Mem.
To GPIB
902 (900)
981
830 (830)
886
902 (900)
809 (840)
830 (830)
756 (780)
389 (343)
388 (343)
374 (333)
374 (333)
56 (47)
56 (47)
56 (47)
56 (47)
Source-Memory4
To Mem.
To GPIB
165 (162)
165
163 (160)
163
165 (162)
164 (162)
163 (160)
162 (160)
133 (126)
132 (126)
131 (125)
131 (125)
44 (38)
44 (38)
44 (38)
44 (38)
Single Reading Operation Reading Rates (rdg./second) for 60Hz (50Hz):
Speed
Fast (488.1)
Fast (488.2)
Medium (488.2)
Normal (488.2)
Measure
To GPIB
537
256 (256)
167 (166)
49
(42)
NPLC/Trigger Origin
0.01 / internal
0.01 / internal
0.10 / internal
1.00 / internal
Source-Measure5
To GPIB
140
79 (83)
72 (70)
34 (31)
Source-Measure Pass/Fail Test4,5
To GPIB
135
79 (83)
69 (70)
35 (30)
Component for 60Hz (50Hz): 4, 6
Speed
Fast
Medium
Normal
NPLC/Trigger Origin
0.01 / external
0.10 / external
1.00 / external
Measure To GPIB
1.04 ms (1.08 ms)
2.55 ms (2.9 ms)
17.53 ms (20.9 ms)
Source Pass/Fail Test
0.5 ms (0.5 ms)
0.5 ms (0.5 ms)
0.5 ms (0.5 ms)
Source-Measure Pass/Fail Test5, 7
To GPIB
4.82 ms (5.3 ms)
6.27 ms (7.1 ms)
21.31 ms (25.0 ms)
NOTES
Reading rates applicable for voltage or current measurements. Auto zero off, autorange off, filter off, display off,
trigger delay = 0, and binary reading format.
Purely resistive lead. 1µA and 10µA ranges <65ms.
3 1000 point sweep was characterized with the source on a fixed range.
1
2
Pass/Fail test performed using one high limit and one low math limit.
Includes time to re-program source to a new level before making m
­ easurement.
6 Time from falling edge of START OF TEST signal to falling edge of end of test signal.
7 Command processing time of :SOURce:VOLTage|CURRent:TRIGgered <nrf> command not included.
4
5
general
Noise Rejection:
Fast
Medium
Slow
1
NPLC
0.01
0.1
1
NMRR
—
—
60 dB
CMRR
80 dB
80 dB
100 dB1
Except lowest 2 current ranges = 90dB.
Load Impedance: Stable into 20,000pF typical.
Common mode voltage: 250V DC (40V DC for Model 2440).
Common Mode Isolation: >109W, <1000pF.
OVERRANGE: 105% of range, source and measure.
Max. Voltage Drop Between Input/Output and sense terminals: 5V.
Max. Sense Lead Resistance: 1MW for rated accuracy.
SENSE INPUT IMPEDANCE: >1010W.
GUARD OFFSET VOLTAGE: <150µV, typical (300µV for Models 2430, 2440).
Source Output modes:
Pulse (Model 2430 only)
Fixed DC level
Memory List (mixed function)
Stair (linear and log)
Memory Buffer: 5,000 readings @ 5 digits (two 2,500 point buffers). Includes selected measured
value(s) and time stamp. Lithium battery ­backup (3 yr+ battery life).
SOURCE MEMORY LIST: 100 points max.
Programmability: IEEE-488 (SCPI-1995.0), RS-232, 5 user-definable power-up states plus
factory default and *RST.
Digital Interface:
Interlock: Active low input.
Handler Interface: Start of test, end of test, 3 category bits. [email protected] 300mA supply.
Not available on Model 2401.
Digital I/O: 1 trigger input, 4 TTL/Relay Drive outputs (33V @ 500mA, diode clamped).
Not available on Model 2401.
Power Supply: 100V to 240V rms, 50–60Hz (automatically detected at power up). Model
2400, 2401: 190VA. Model 2410: 210VA. Model 2420: 220VA. Model 2425, 2430: 250VA.
Model 2440: 240VA.
COOLING: Model 2401: Convection. Model 2410, 2420, 2425, 2430, 2440: Forced air,
variable speed.
EMC: Conforms to European Union Directive 89/336/EEC, EN 61326-1.
Safety: UL listed to UL 61010B-1:2003: Conforms to European Union Low Voltage Directive.
Vibration: MIL-PRF-28800F Class 3 Random.
WARM-UP: 1 hour to rated accuracies.
DIMENSIONS: 89mm high × 213mm wide × 370mm deep (3½ in × 83⁄8 in × 149⁄16 in). Bench
Configuration (with handle and feet):104mm high × 238mm wide × 370mm deep (41⁄8 in ×
93⁄8 in × 149⁄16 in).
WEIGHT: 3.21kg (7.08 lbs) (Model 2425, 2430, 2440: 4.1kg, 9.0 lbs).
ENVIRONMENT: Operating: 0°–50°C, 70% R.H. up to 35°C. Derate 3% R.H./°C, 35°–50°C.
Storage: –25°C to 65°C.
1.888.KEITHLEY (U.S. only)
www.keithley.com
A Greater Measure of Confidence
SMU INSTRUMENTS
Series 2400 condensed specifications
Speed
Measure
To Mem.
To GPIB
2081 (2030) 1754
1239 (1200) 1254
2081 (2030) 1198 (1210)
1239 (1200) 1079 (1050)
510 (433)
509 (433)
438 (380)
438 (380)
59
(49)
59 (49)
57
(48)
57 (48)
Series 2400 condensed specifications
Sweep Operation3 Reading Rates (rdg./second) for 60Hz (50Hz):
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Keithley Instruments, Inc.:
2410-C 2430-C 2400 2420-C 2401 2440-C 2440 2430 2425-C 2400-C 2425 2410 2420
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement