CleanStar GRAVITY V2200 Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS

BEFORE USING THIS APPLIANCE

WARNINGTo reduce the risk of fire, electric shock, or injury:

1. Do not leave the vacuum cleaner unattended when plugged in. Unplug from outlet when not in use.

2. To reduce the risk of electric shock, do not use outdoors or on wet surfaces

3. Use only as described in this manual. Use only manufacturers recommend attachments.

4. Do not use with a damaged cord or plug. If vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water, do not use the product, and take it to a service center prior to use.

5. Do not pull the cord beyond its full extended length, do not use cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces/area or anywhere where it may burn.

6. Do not unplug the unit by pulling on the cord. To unplug, grasp the plug, not the cord.

7. Do not handle the plug or vacuum cleaner with wet hands.

8. Do not put any object into openings. Do not use with any openings blocked. Keep free of dust, lint, hair and anything that may reduce airflow.

9. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

10. Turn all controls off before unplugging.

11. Use extra care when cleaning on stairs.

12. Do not use to pick up any liquids, powders, plaster dust, flammable or combustible liquids, such as gasoline, or use in areas where they may be present. This will void your warranty.

13. Hold the plug when rewinding the power cord onto the cord reel. Do not allow the plug to whip when rewinding.

14. Unplug before connecting the hose

15. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

16. Do not use without dust bag and/or filter in place.

17. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

18. Filters, tools and accessories are consumable items and not covered under warranty.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

- 2 -

COMPONENTS AND EQUIPMENT

6. Motor speed regulator knob

9. Suction hose connection

- 3 -

PREVENTION

Switch off the vacuum cleaner immediately if the air intakes, hose, floor brush or the telescopic tube becomes blocked. Before starting the vacuum cleaner up again remove the object causing the blockage:

1. Never use the vacuum cleaner in the immediate vicinity of hot bodies and do not suck up hot objects such as cigarette ends or ashes.

2. Only place the plug in the socket when your hands are dry.

3. Please remove large or sharp objects from the floor before using the vacuum cleaner to avoid any possible damage to it.

4. Do not pull by the mains cable when pulling out the plug.

- 4 -

ASSEMBLING THE VACUUM CLEANER

1. Assembly and disassembly of the tube

 Assembly:

Insert the hose end in the air intake opening.

Push the hose end in until it locks in place

 Disassembly:

Take the hose end out from the air intake after disconnecting from the mains socket.

2. Assembling the telescopic tube and accessories

2.1: Remove the telescopic tube from the hand grip.

2.2:

 Set the telescopic tube to the correct length.

 Push the telescopic tube slide forwards and pull out the lower part of the tube to the extension length required. Then simply let go of the slide and let it snap into place

2.3: Fix the floor brush to the telescopic tube.

2.4: Suitable for everyday cleaning of the carpet

and hard floor surfaces.

- 5 -

Furniture brush

Upholstery nozzle

Floor nozzle: Settings for carpets and tiled, wood-block or similar floors:

A: Hard floors = brush bar extended

B: Carpets = brush bar retracted

OPERATION

Vacuum cleaning

1: Before using the device first roll out a sufficient length of electric flex cable and plug into the mains socket.

The yellow mark on the electric flex cable is the maximum length that must not be exceeded.

To switch on the device press the foot pedal button on the casing with your foot

- 6 -

2: To rewind the power cable, press the button

with one hand and guide the cable with the other hand to ensure that it does not whip causing damage.

Regulating the suction power

You can set the suction power on the device individually as you require it using the suction regulator. We recommend using minimum suction power for delicate materials. Select medium suction power for mattresses, upholstered furniture and carpets. Select maximum suction power for tiled, wood and other robust floors.

- 7 -

CYCLONE CLEANING SYSTEM

The unit has a cyclone vacuum cleaner function without needing a dust bag. The sucked up dirt is forced into the dust container. The air is cleaned by a washable permanent filter in the dust container, motor protection filter and an exhaust air filter (HEPA filter).

Caution!

Never vacuum clean without a filter or with a damaged filter. The dust that is sucked up would force its way into the device and damage the motor.

Clean dust / dirt in the dust container by an entirely new method ---it’s simple, clean and so easy.

Caution!

Over Heating Protection:

In order to avoid Motor Over-Heating caused by abnormal operation （ Outlet of Ventilation is blocked … ..eg., ） this vacuum cleaner is equipped with Motor Over-Heating Protection. When vacuum cleaner is suddenly stopped please wait for five minutes, then you may press power on/off switch to restart the Vacuum Cleaner.

Emptying dust container

You can easily see with the transparent dust container when

it must be emptied.

1. Switch off the vacuum cleaner and disconnect the plug from the mains. To do this always pull on the plug and not on the cable.

2. You can pull the dust container together with the cleaning system out of their anchoring with the aid of the carrier handle on the dust container. Now lift out the dust container and carry it to the waste bin.

3. A push button is located on the dust container that you can use to open and empty it automatically (bottom-down technology).

To do this hold the dust container over your dustbin and press on the empty button.

4. After emptying it clean the air filter again if necessary

(see also Cleaning the air filter below). After this rinse out the dust container and wipe it dry. Make sure it is dry before use.

5. After this push the air filter cleaning system back into position in the cyclone vacuum cleaner until it snaps into place. Your cyclone vacuum cleaner is now ready for use again.

- 8 -

Cleaning the sponge filter

The sponge filter and the sponge cover should be cleaned regularly. Cleaning is best done when emptying the dust container. To do this follow the instructions in the Emptying dust container section.

1. Switch off the vacuum cleaner and disconnect the plug from the mains. To do this always pull on the plug and not on the cable.

2. You can pull the dust container together with the cyclone cleaning system out of their anchoring with the aid of the carrier handle on the dust container. Take hold of the carrier handle on the dust container and pull it upwards.

3. Turn the sponge cover over and take out the sponge filter

4. Now rinse the sponge filter under running water and allow it to dry.

5. Place the sponge filter back in the sponge cover (or replace with a new one) and fit it into the dust container.until it snaps into place. Your cyclone vacuum cleaner is now ready for use again.

Cleaning the exhaust air filter (HEPA filter)

The exhaust air filter cleans the air a final time before it leaves the vacuum cleaner. You can clean the exhaust air filter as follows:

1. Switch off the vacuum cleaner and disconnect the plug from the mains. To do this always pull on the plug and not on the cable.

2. Open the exhaust air grill (this is at the rear of the cyclone vacuum cleaner.)

3. The exhaust air filter is visible when the grill has been opened.

4. Rinse the filter under cold running water and allow dry.

5. Put the exhaust air filter back into place (or replace with a new one) and place in the grill.

6. Close the exhaust air filter grill.

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

Contact you local government for information regarding the collection systems available.

If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water and get into the food chain, damaging your health and well-being.

- 9 -