User manual | null User manual

e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
e-con Systems India Pvt Ltd
17, 54th Street,
Ashok Nagar
Chennai-600083
www.e-consystems.com
e-CAM50_OMAP_GSTIX
User Manual
Revision 1.2
Tuesday, July 19, 2011
Customer/ Partner
www.e-consystems.com | Subject to change without notice
Page 1 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
Contents
1
2
3
4
5
6
7
REVISION HISTORY ............................................................................................................................ 3
INTRODUCTIONS ................................................................................................................................ 4
SCOPE .................................................................................................................................................. 4
Attachment of e-CAM50_OMAP_GSTIX board with PALO Board ....................................................... 4
Accessories required ............................................................................................................................. 9
Mechanical requirements ...................................................................................................................... 9
Connector Pin out Details ................................................................................................................... 10
Figures
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
e-CAM50_OMAP_GSTIX front board View .......................................................................................... 4
e-CAM50_OMAP_GSTIX Rear board View .......................................................................................... 4
PALO Board – View .............................................................................................................................. 5
Interface cable ....................................................................................................................................... 6
Attachment of Interface cable to PALO Board………………………………………………………………6
Attachment of Interface cable to e-CAM50_OMAP_GSTIX ................................................................. 7
Power cable…………………………………………………………………………………………………….7
Attachment of Power cable ................................................................................................................... 8
Connecting Power cable to e-CAM50_OMAP_GSTIX Board ............................................................... 8
Attachment of Power cable and Interface cable ................................................................................... 9
Tables
a.
b.
c.
d.
PALO Board Connector Pin out (J5- 27 Pin) ....................................................................................... 10
e-CAM50_OMAP_GSTIX Board Connector Pin out (CN3-27 Pin) ..................................................... 11
e-CAM50_5642_MOD camera connector Pin out (CN2 - 24 Pin) ...................................................... 12
Connector Part Numbers .................................................................................................................... 13
www.e-consystems.com | Subject to change without notice
Page 2 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
e-CAM50_OMAP_GSTIX
1 REVISION HISTORY
Rev No
1.0
1.1
1.2
Date
Nov 10, 2010
Nov 10, 2010
Jul 19, 2011
Major Changes
Author
Initial draft version
S.Raghavendran
Updated E-con cable
S.Raghavendran
Updated Picture &Connector
pin out details
A.Shifana
www.e-consystems.com | Subject to change without notice
Page 3 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
2 INTRODUCTIONS
The e-CAM50_OMAP_GSTIX is an add on board from e-con Systems which works plug and play with every
Gumstix Overo computer-on-module (COM). This board provides the still capture upto resolution of 5MP.
3 SCOPE
The scope of this document is limited to the attachment of the e-CAM50_OMAP_GSTIX with PALO Board from
Gumstix.
The reader is assumed to have knowledge about gumstix processor board OVERO and it is reference Palo board its
connector details, working of the same.
4 Attachment of e-CAM50_OMAP_GSTIX board with PALO Board
I.
e-CAM50_OMAP_GSTIX front board View
Fig-1
II.
e-CAM50_OMAP_GSTIX Rear board View
F
i
g
2
Fig-2
www.e-consystems.com | Subject to change without notice
Page 4 of 13
e-CAM50_OMAP_GSTIX
III.
USER MANUAL
19 July 2011
PALO Board – View
J5 Connector- 27 Pin
Fig-3
www.e-consystems.com | Subject to change without notice
Page 5 of 13
e-CAM50_OMAP_GSTIX
IV.
USER MANUAL
19 July 2011
Interface cable
Fig-4
V.
Attachment of Interface cable to PALO Board
Fig-5
www.e-consystems.com | Subject to change without notice
Page 6 of 13
e-CAM50_OMAP_GSTIX
VI.
USER MANUAL
19 July 2011
Attachment of Interface cable to e-CAM50_OMAP_GSTIX
Fig-6
VII.
Power cable
Fig-7
www.e-consystems.com | Subject to change without notice
Page 7 of 13
e-CAM50_OMAP_GSTIX
VIII.
USER MANUAL
19 July 2011
Attachment of Power cable
Connecting Power cable to PALO board
Fig-8
IX.
Connecting Power cable to e-CAM50_OMAP_GSTIX Board
Fig-9
www.e-consystems.com | Subject to change without notice
Page 8 of 13
e-CAM50_OMAP_GSTIX
X.
USER MANUAL
19 July 2011
Attachment of Power cable and Interface cable
Fig-10
5 Accessories required
1. PALO board from gumstix – 1no
2. Overo processor board -1no
4. Power cable – 1 no
5. 2 Pin male connector- 1 no
4. Interface Cable -1 no
5. SD Card- 1 no
6 Mechanical requirements
The camera board fixing should be fixed as per the target application of customer requirements.
econ is not recommending any specific solution for mechanical fixing.
www.e-consystems.com | Subject to change without notice
Page 9 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
7 Connector Pin out Details
a. PALO Board Connector Pin out (J5- 27 Pin)
J5
Pin No
Signal Name
Description
1
GPIO94_CAM_HS
Camera horizontal Synchronization
2
GPIO95_CAM_VS
Camera vertical Synchronization
3
GPIO96_CAM_XCLKA
Camera Master clock
4
GPIO97_CAM_PCLK
Camera pixel clock
5
GPIO98_CAM_FLD
Camera Reset
6
GPIO99_CAM_D0
Camera Data D0
7
GPIO100_CAM_D1
Camera Data D1
8
GPIO101_CAM_02
Camera buffer Data D2
9
GPIO102_CM_D3
Camera buffer Data D3
10
GPIO103_CIF_DD04
Camera buffer Data D4
11
GPIO104_CIF_DD05
Camera buffer Data D5
12
GPIO105_CAM_D6
Camera buffer Data D6
13
GPIO106_CIF_DD07
Camera buffer Data D7
14
GPIO107_CIF_DD08
Camera buffer Data D8
15
CPIO108_CIF_DD09
Camera buffer Data D9
16
GPIO109_CAM_D10
Camera Data D10
17
GPIO110_CAM_D11
Camera Data D11
18
GPIO111_CAM_XCLKB
Clock signal
19
GPIO167_CAM_WEN
Power down mode enable active high
20
GPIO126_CAM_STROBE
Camera Strobe signal
21
VDDS_1.8
Power
22
SYSEN
System Enable
www.e-consystems.com | Subject to change without notice
Page 10 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
23
GND
Ground Signal
24
VCC3P3
Power
25
GPIO63_CAM_IRQ
Camera IRQ Signal
26
GPIO184_I2C3_SCL
I2C SCL Signal
27
GPIO185_I2C3_SDA
I2C SDA Signal
19 July 2011
b. e-CAM50_OMAP_GSTIX Board Connector Pin out (CN3-27 Pin)
CN3
Pin No
Signal Name
Description
1
OMAP_I2C_SDA
I2C SDA Signal
2
OMAP_I2C_SCL
I2C SCL Signal
3
CAM_IRQ
Camera IRQ Signal
4
VCC3P3
Power
5
GND
Ground Signal
6
SYSEN
System Enable
7
VCC_1P8
Power
8
OMAP_STROBE
OMAP Strobe signal
9
OMAP_CAM_PWDN
Power down mode enable active high
10
OMAP_XCLKB
OMAP Clock signal
11
CAM_OMAP_D11
Camera OMAP Data D11
12
CAM_OMAP_D10
Camera OMAP Data D10
13
BUF_CAM_OMAP_D9
Camera OMAP buffer Data D9
14
BUF_CAM_OMAP_D8
Camera OMAP buffer Data D8
15
BUF_CAM_OMAP_D7
Camera OMAP buffer Data D7
16
BUF_CAM_OMAP_D6
Camera OMAP buffer Data D6
17
BUF_CAM_OMAP_D5
Camera OMAP buffer Data D5
18
BUF_CAM_OMAP_D4
Camera OMAP buffer Data D4
www.e-consystems.com | Subject to change without notice
Page 11 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19
BUF_CAM_OMAP_D3
Camera OMAP buffer Data D3
20
BUF_CAM_OMAP_D2
Camera OMAP buffer Data D2
21
CAM_OMAP_D1
Camera OMAP Data D1
22
CAM_OMAP_D0
Camera OMAP Data D0
23
nOMAP_CAM_RST
OMAP Camera Reset
24
CLK_PIXEL_CAM_OMAP_BUF
Camera OMAP pixel clock
25
CLK_MASTER_OMAP_CAM
Camera OMAP Master clock
26
BUF_CAM_OMAP_FV
Camera vertical Synchronization
27
BUF_CAM_OMAP_LV
Camera horizontal Synchronization
19 July 2011
c. e-CAM50_5642_MOD camera connector Pin out (CN2 - 24 Pin)
Pin. No
Signal Name
Description
1
GND
Ground signal
2
VCC3P3
Power
3
CAM OMAP D4
Camera data output line 4
4
CAM OMAP D3
Camera data output line 3
5
CAM OMAP D5
Camera data output line 5
6
CAM OMAP D2
Camera data output line 2
7
CAM OMAP D6
Camera data output line 6
8
CLK_PIXEL_CAM_OMAP
Camera Pixel clock
9
CAM OMAP D7
Camera data output line 7
10
GND
Ground Signal
11
CAM OMAP D8
Camera data output line 8
12
CLK_MASTER_OMAP_CAM_BUF
Camera OMAP Master clock
13
CAM OMAP D9
Camera data output line 9
www.e-consystems.com | Subject to change without notice
Page 12 of 13
e-CAM50_OMAP_GSTIX
USER MANUAL
19 July 2011
14
VCC1P8
Power
15
DVDD
Do not connect
16
CAM_OMAP_LV
Digital video horizontal
synchronization output
17
BUF_OMAP_CAM_PWDN
Power down mode enable active
high
18
CAM_OMAP_FV
Digital video vertical
synchronization output
19
BUF_nOMAP_CAM_RST
Camera Reset Signal
20
OMAP_I2C_SCL
Sensor I2C SCL signal
21
VCC2P8
Power
22
OMAP_I2C_SDA
Sensor I2C SDA signal
23
GND
Ground Signal
24
SENSOR_STROBE
Camera strobe signal
d. Connector Part Numbers
Connector
Description
Manufacturer
Part Number
27 Pin PALO Board
Connector (J5)
0.3mm Contact Pitch, 1mm above
the board, Flexible Printed Circuit
ZIF Connectors
Hirose Electric
FH26-27S-0.3SHW
27 Pin eCam50 Board
Connector (CN3)
CONN FPC Double side contacts
0.30mm 27Pos Right Angled
SMD
Omron
XF2B-2745-31A
24 Pin Camera
Connector (CN2)
CONN FPC Double side contacts
0.50mm 24Pos Right Angled
SMD
Hirose Electric
FH19SC-24S0.5SH(05)
www.e-consystems.com | Subject to change without notice
Page 13 of 13

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project