CR9, CP9, CT9

Add to my manuals
108 Pages

advertisement

CR9, CP9, CT9 | Manualzz

CR9, CP9, CT9

Celeron® M / Pentium® M

6U CompactPCI® SBC with Hot Swap

Hardware User’s Manual

Edition 2.6

Copyright © 2003, © 2004, © 2005, © 2006, © 2007 SBS Technologies. All rights reserved.

CR9, CP9, CT9 Hardware User’s Manual

This manual applies to the CR9, CP9, CT9 Celeron® M/Pentium® M PC/AT Compatible 6U CompactPCI®

Single Board Computer hardware revision 2.0 and above, until superseded.

Rev /ID Date Chapter Comments

0.0 First release

0.1 MF

24. Nov. 2003 All

Footer

I/O Connector

J7003,

23. Dec. 2003

J7004, and J7005

Environment

Conditions

Title changed

J7005: RS422/485 interface names added to COM2

Table corrected

Minor typos corrected and formatting changed

0.2 MF 26. Jan. 2004

All

PMC1 Connectors

P6201, P6202, and

P6203

Compliant to VITA 32-2003

PMC2 Connectors

P7201, P7202

1.0 PS 1. July 2004

Placement Plans

Enter Setup

Specifications

Doc-layout

Specifications

CTM12

Temp. sensors

Compliant to VITA 32-2003

Updated to board revision V1.x

Press DEL when LED goes green

Maximum external battery voltage corrected

Heading styles renamed to standard

Battery external input and life time corrected

6U x 4HE/HP transition module

External Battery

Style table

Feature list

Specifications

Specifications description of both LM75 added

Hints for operating without onboard battery

Speaker is mounted for R-, 6-Style

Pentium M 1.8 GHz and Celeron M 1.3 GHz added

Operating thermal data and notes updated

Supply Voltage Ranges added

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 3

2.0 PS 19. Oct. 2004

Placement Plans

Footer

Updated to board revision V2.x

Updated to correct manual revision

Ethernet Interface

.

LED colors were mixed up between front panel and transition module CTM12

PMC interface

.

With board revision V2 and higher PMC slot 1 is

PCI-X capable with 66/100/133 MHz

Various

Specification

Hot Swap

External Battery

Input

Specification

Transition module

CTM12

Typos corrected with P700x for the CPCI connectors

Isolation voltage info added

Info about used pre-charge resistors added

More Hints added about working with battery less boards and storing Setup information then

Power consumption section updated

P7700/P7701 Power input/output clarified, fused and unfused +5 V corrected

2.1 PS

2.2 PS

2.3 HHS

2.4 MF

16. Dec. 2004

Not final

29. Aug. 2005

SMBus devices

External SMBus

.

External Access to onboard SMBus can only be done via the IPMI controller

Various

SMBus address of P64H2 updated

Typos corrected and improved

PMC1 Connector

App. B PMC

DVI

External Manuals

Getting Started

Transition module

Video connectors

Specification

IDSEL lines corrected, EREADY removed

Table max. current adjusted for Cx9

Max. resolution is limited to 1024x768

Referencing names corrected

Content of Application Note added into the manual

Never use two display devices connected to the rear of the Cx9. You have to use one front, one rear.

Height section added

Resources,

Function Blocks

Function Blocks

Serial ports

Function Blocks

GPIO

All chapters

APIC controller section with short description added, more Info with ICH4 datasheet

Watchdog section updated

RS485 drivers are enabled with DTR signal

Processor section added

Corrected to be on J7004

Cosmetic changes

Boiler plates

Technical corrections

Height and P1801 corrections check layout

Minor Cosmetic changes

2.5 HHS,

MF

11. May 2006 All chapters

29. June 2006

Legal Information

Page 23, 62, 63, 95

Page 22

Page 30

Table 24

Change China address

Add info on ATI Radeon graphics

Reference to LSI Logic SCSI BIOS deleted

Requirement for +3.3 V added

VxWorks and Linux added

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 4

2.6 HHS,

MF

Page 90

Page 69

22. May 2007 All

Figure renamed

RoHS compliance statement added

Cosmetic changes

Support

Title

Table 28

Figure 18

CTM12

Updated list of web site addresses

Change title, header and footer

Power Consumption for Celeron M 1.0 GHz and

Pentium M 1.4 GHz added

Temperature Curve updated for new processors

Correct pins on P2000

Page 7

Chap. 2 & 3

Insert Waste Disposal (WEEE) info

Update

Chap. 8, Specific. Insert note on electrical clearance

Chap. 3 Correct configuration paragraph

Environment

Conditions

Chap. 1, Chap. 7

Chap. 5

Intro

Correct storage temperature values & styles (non-

RoHS)

Insert info about EIDE/PATA transfer speed limits change primary/secondary on EIDE

Replace front panel drawings

Insert CE conformance text

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 5

Legal Information

Legal Disclaimers

© 2006 SBS Technologies, Inc. All rights reserved.

The information in this manual is proprietary to and is the confidential information of SBS Technologies, Inc. (SBS) and may not be reproduced in whole or in part, for any purpose, in any form or by any means, electronic, mechanical, recording, or otherwise, without written consent of SBS

Technologies, Inc. Use, disclosure, and reproduction is permitted only under the terms of an SBS license agreement or explicit written permission of SBS.

You are not authorized to use this document or its contents until you have read and agreed to the applicable license agreement. Receipt of this publication is considered acceptance of these conditions.

All information contained in this document has been carefully checked and is believed to be entirely reliable and consistent with the product that it describes.

However, no responsibility is assumed for inaccuracies. SBS assumes no liability due to the application or use of any product or circuit described herein; no liability is accepted concerning the use of SBS products in life support systems. SBS reserves the right to make changes to any product and product documentation in an effort to improve performance, reliability, or design.

THIS DOCUMENT AND ITS CONTENTS ARE PROVIDED AS IS, WITH

NO WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED,

INCLUDING WARRANTIES OF DESIGN, MERCHANTABILITY, AND

FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM ANY

COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

Changes or modifications to this unit, not expressly approved by SBS, could void the user’s authority to operate the equipment.

All computer code and software contained in this document is licensed to be used only in connection with an SBS hardware product. Even if this code or software is merged with any other code or software program, it remains subject to the terms and conditions of this license. If you copy, or merge, this code or software, you must reproduce and include all SBS copyright notices and any other proprietary rights notices.

The content of this manual if furnished for informational use only and is subject to change without notice. Reverse engineering of any SBS product is strictly prohibited.

In no event will SBS be liable for any lost revenue or profits or other special, indirect, incidental and consequential damage, even if SBS has been advised of the possibility of such damages, as a result of the usage of this document and the software that this document describes. The entire liability of SBS shall be limited to the amount paid by you for this document and its contents.

SBS shall have no liability with respect to the infringement of copyrights, trade secrets, or any patents by this document of any part thereof. Please see the applicable software license agreement for full disclaimer or warranties and limitations of liability.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 7

This disclaimer of warranty extends to SBS’ licensees, to licensees transfers, and to licensees customers or users and is in lieu of all warranties expressed, implied, or statutory, included implied warranties of scalability or fitness for a particular purpose.

SBS Technologies and the SBS logo are trademarks of SBS Technologies, Inc.

Other brand names and product names contained herein may be claimed as the property of others.

SBS Technologies, Inc., 7401 Snaproll NE, Albuquerque, NM 87109, U.S.A.

Regulatory compliance

Products sold or transferred between companies or operated on company premises (factory floor, laboratory) do not need CE, FCC or equivalent certification. Boards or subsystems which cannot provide a useful function on their own do not need certification.

Certification can only be granted to complete and operational systems. There are authorized testing agencies, regulatory organizations and laboratories who will issue certificates of compliance after system testing.

SBS Technologies designs and tests all their products for EMI/EMC conformance. Where SBS Technologies supplies a complete/functional system for use by end users a certificate will be cited in the manuals/documents which are provided with the products.

Products manufactured by SBS Technologies should normally be suitable for use in properly designed and produced customer equipment (system boxes or operational systems) without any major redesign or additional filtering.

However, the systems might not conform to specific regulations once assembled and used. The system integrator or installer must test for compliance as required in his country or by the intended application and certify this to the end user.

ESD/EMI issues

ESD (Electro-Static Discharge) and EMI (Electro-Magnetic Interference) issues may show up in complete and operational systems. There are many ways to avoid problems with these issues.

Any operational system with cables for I/O signals, connectivity or peripheral devices provides an entry point for ESD and EMI. If SBS does not manufacture the complete system, including enclosure and cables, it is the responsibility of the system integrator and end user to protect their system against potential problems. Filtering, optical isolation, ESD gaskets and other measures might be required at the physical point of entry (enclosure wall of box or rack). For example it is state-of-the-art that protection can not be done at the internal connector of an RTM if a cable is attached and routed outside the enclosure. It has to be done at the physical entry point as specified above.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 8

Products manufactured by SBS Technologies should normally be suitable for use in properly designed and produced customer equipment (system boxes or operational systems) without any major redesign. However, the systems might be subject to problems and issues once assembled, cabled and used. The end user, system integrator or installer must test for possible problems and in some cases show compliance to local regulations as required in his country or by the intended application.

Waste Disposal

The mark or symbol on any electrical or electronic product shows that this product may not be disposed off in a trash bin. Such goods have to be returned to the original vendor or to a properly authorized collection point.

Electric waste disposal symbol with black bar as explained below

The black bar underneath the waste bin symbol shows that the product was placed on the market after 13 August 2005. Alternatively the date of ‘placed on the market’ is shown in place of the bar symbol.

CE conformance declaration

CE certification is required in EU countries for equipment which is used/operated by the end user. Products sold or transferred between companies or operated on company premises (factory floor, laboratory) do not need CE certification.

CE certification can only be granted to complete and operational systems.

Boards or subsystems which cannot provide a useful function on their own do not need CE certification.

SBS Technologies designs and tests all their products for EMI/EMC conformance. Products manufactured by SBS Technologies should normally be suitable for use in properly designed and produced customer equipment (system boxes or operational systems) without any major redesign or additional filtering. The system integrator or installer must, in any case, test for CE compliance and certify this to the end user.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 9

Corporate headquarters

SBS Technologies Inc.

7401 Snaproll St., NE

Albuquerque, NM 87109

U.S.A.

Phone: +1-505-875-0600

Fax: +1-505-875-0400

Email: [email protected]

Regional headquarters

US EU

Americas & Pacific Rim (Japan,

Korea, China, Philippines, AUS,

NZ)

Europe, Russia, Near East, India, Africa

SBS Technologies, Inc.

7401 Snaproll St., NE

SBS Technologies GmbH & Co. KG

Memminger Str. 14

Albuquerque, NM 87109 86159 Augsburg

U.S.A. Germany

Phone: +1-505-875-0600 Phone: +49-821-5034-0

Fax: +1-505-875-0400 Fax: +49-821-5034-119

Email: [email protected] E-Mail: [email protected]

SBS Technologies on the Web: http://www.sbs.com

Chinese language address and web site

SBS Technologies

Room 501-502

Cyber Times Tower B

Tianan Cyber Park

Futian District

Shenzhen 518041

P.R. China

Phone: +86-755-8347-5668

Fax: +86-755-8347-6535

Email: [email protected]

Web: http://china.sbs.com

For contact and other information (service, warranty, support etc.) see address list in chapter: ‘Support, Service’.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 10

Welcome

The CR9, CP9, CT9 CompactPCI Single Board Computer is a fully IBM-AT compatible stand-alone PC equipped with numerous functions and add-on features on a minimized board size. This technical manual is designed to provide information regarding the general use and application of the CR9, CP9,

CT9 CompactPCI Single Board Computer, as well as detail the hardware design. Software methods and programming information are also provided.

Chapter 1 gives a brief overview of the functions, features and devices of the

CR9, CP9 and CT9.

Chapter 2 and 3 illustrate unpacking and installation procedures.

Chapter 4 describes how to get started

Chapter 5 describes all onboard and panel interfaces with pin assignments.

Chapter 6 contains notes on system resources.

Chapter 7 lists details of the function blocks.

Chapter 7 describes electrical and environmental specifications.

A number of expansion and add-on products are available for the CR9, CP9 and CT9. The CTM12 transition module and the PMC module are described in appendices to this manual. Please observe all safety instructions when handling

SBS products as outlined in the unpacking and installation chapters.

The following documents also cover items relevant to the CR9, CP9 and CT9

CompactPCI Single Board Computer. All documents are included as files on the Technical Product Information CD-ROM.

• CR9, CT9, CP9, VR9, VP9 User’s Manual for AMIBIOS8 Setup

• CR9, CT9, CP9, VR9, VP9 Board Specific Hardware Programmer’s

Manual

• AMIBIOS8 Check Point and Beep Code List

• AMIBIOS8 Error Messages

• Intelligent Platform Management Interface for CT9 User’s Manual

Typographic Conventions

This manual uses the following notation conventions:

Italics (sometimes additional in blue color) emphasize words in text or documentation or chapter titles or web addresses if underlined.

• Hexadecimal values (base 16) are represented as digits followed by “h”, for example: 0Ch.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 11

Product Properties

• Hexadecimal values (base 16) are represented as digits preceded by “H”, for example: H0C.

• Hexadecimal values (base 16) are represented as digits preceded by “$”, for example: $0C.

• Binary values (base 2) are represented as digits followed by “b”, for example 01b

• The use of a “#” (hash) suffix to a signal name indicates an active low signal. The signal is either true when it is at a logic zero level (voltage close to 0 V) or the signal initiates actions on a high-to-low transition.

• The use of a “\” (backslash) prefix to a signal name indicates an active low signal. The signal is either true when it is at a logic zero level (voltage close to 0 V) or the signal initiates actions on a high-to-low transition.

• Text in Courier font indicates a command entry or output from an SBS embedded PC product using the built-in character set.

• Notes, warning symbols and cautions call attention to essential information.

Certification

The product or products described in this technical manual cannot be operated by themselves. They are components for integration into operational systems or add-ons to such systems. The products have been designed to meet relevant regulatory standards like FCC and CE. As mandated by these standards conformance to these standards can only be certified for complete operational systems. This has to be done by the end-user or by the systems integrator in their operational systems. SBS Technologies have tested some products in their own systems. Upon request information is available which products have been tested and about the specific environment under which SBS has tested these components.

Altitude

Altitude, air pressure and ambient temperature influence the thermal operation of the components described in this manual. They have been developed and tested at about 500 m (1650 ft.) above sea level at a typical ambient temperature of 20 °C (68 °F). Because of only marginal variations within a limited range of altitudes these products operate as specified within altitudes from sea level to 1000 m (3300 ft.). SBS Technologies can assist the user of these components in planning operation outside this altitude range upon request.

Options

This manual describes the basic product plus all options. Your product may not have all options implemented. Please verify with your purchase contract which options are implemented. Descriptions of options which are not implemented obviously do not apply to your product.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 12

Support, Service and Warranty

The manufacturer grants the original purchaser of SBS products a warranty of

24 months from the date of delivery. For details regarding this warranty refer to

Terms & Conditions of the initial sale.

Please see chapter ‘Support, Service, and Warranty Information’ for further details on repairs and product support.

For support on the web and product information, visit our website at http://www.sbs.com

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 13

.

Contents

Legal Information

Legal Disclaimers

Regulatory compliance

ESD/EMI issues

Waste Disposal

Corporate headquarters

WELCOME 11

Product Properties 12

Certification 12

Altitude 12

Support, Service and Warranty 13

CONTENTS 15

7

7

8

8

9

10

.

CHAPTER 1

CHAPTER 2

INTRODUCTION 23

Design Features 26

UNPACKING AND INSPECTION

Delivery Volume

Available Accessories

29

29

29

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 15

CHAPTER 3

CHAPTER 4

CHAPTER 5

ESD 30

Warning 30

Initial Inspection 31

Unpacking 31

Handling 32

INSTALLATION 35

Installation preparation

General Advisories

Advice on CompactPCI products

35

35

35

Required items

Installation of a plug-in board

Installation of a plug-on module (mezzanine)

36

37

37

Installation of the Rear Transition Module CTM12

Initial Power-On Operation

Entering the BIOS SETUP

38

39

39

GETTING STARTED

Power Supply

Status indicator, Postcode and Beeps

Booting 42

Setup 43

Hot Swap on Cx9

Unexpected Resets

44

44

41

41

42

INTERFACES 45

Front Panel Interfaces 46

Cx9 Connectors

CPCI connector reference

CompactPCI bus Connector J7001 and J7002

46

46

48

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 16

CHAPTER 6

CHAPTER 7

I/O Connector J7003, J7004, and J7005

EIDE Connector P1800

Keyboard and PS/2 Mouse Interface P2001

Ethernet Interface U5600 and U5650

Serial Port COM1 P2201

VGA Interface P4200

USB Interfaces P1680

PMC2 Connectors P7201, P7202

PMC-I/O Connector P6204 and P7204

RESOURCES 61

Memory Map 61

Register Set

Standard Register Set

61

62

Interrupts 63

APIC Controller 64

49

51

52

53

54

55

56

58

59

FUNCTION BLOCKS 65

Processor 65

Memory Controller 65

DMA Controller

Interrupt Controller

65

66

Timer 66

Real Time Clock 67

Keyboard and Mouse Controller

EIDE Interface

USB Interface

Serial Interface

Parallel Interface

Floppy Controller

Graphics Controller

68

68

68

67

67

67

68

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 17

CHAPTER 8

Software Installation

PMC Interface

69

69

IPMI (CT9)

Ethernet Interface

Software Installation

Additional devices

Hot Swap

SMBus devices

SMBus external (IPMB)

Temperature Sensor LM83

Temperature Sensors LM75

Serial EEPROM

Power Management Event

INTP, INTS

ENUM# 73

Geographic Addressing 73

GPIO (0...7) 73

Watchdog 73

72

72

72

72

70

70

71

71

72

Programmable Timer 73

LEDs 74

Reset Button 74

Speaker 74

69

70

70

SPECIFICATIONS 75

Power Consumption 76

Onboard Lithium Battery

Environment Conditions

78

79

Electrical Characteristics

Supply voltage range

81

81

GPIO 0...7

Electrical clearance

82

82

Isolation 82

Placement Plan Component Side Cx9 V2 83

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 18

APPENDIX A

APPENDIX B

APPENDIX C

Placement Plan Solder Side Cx9 V2

TRANSITION MODULE CTM12

EIDE Connector P1800

Ethernet Interface 10/100/1000BaseT P5000 and P5500

Parallel Interface LPT1 P2002

Serial Interfaces COM1 P2200 and COM2 P2201/P2203

VGA Interface P4001

DVI-I connector P4100

USB connector P2005

Floppy connector P2003/2004

Miscellaneous connector

PMC I/O connectors

Power connector P1801

Power IN/OUT connectors P7700, P7701

Placement Plan

PCI MEZZANINE CARD (PMC)

Electrical characteristics

99

99

SUPPORT, SERVICE

Technical Support

101

101

102 Support on the Web

Warranty 102

Repairs 102

Warranty Repairs 102

Non-Warranty Repairs 103

Procedure 103

Obtaining an RMA Number

Shipping the Product

103

104

Error Report Form 105

84

92

92

94

94

96

97

85

87

87

89

90

90

91

98

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 19

List of Figures

F IGURE 1: S AMPLE PICTURE OF C X 9 BOARD .............................................................................................................. 23

F IGURE 2: L OGICAL DIAGRAM OF C X 9 BOARD .......................................................................................................... 25

F IGURE 3: B OARD PACKAGING .................................................................................................................................. 32

F IGURE 4: H ANDLING THE C X 9 BOARD ..................................................................................................................... 33

F IGURE 5: 6U BOARD INSERTION INTO SYSTEM BOX .................................................................................................. 37

F IGURE 6: I NSTALLING A PMC ON A 6U CPCI CARRIER BOARD ................................................................................ 38

F IGURE 7: L OCATION OF COMPONENTS ON BOARD AND FRONT PANEL ...................................................................... 45

F IGURE 8: S INGLE SLOT FRONT PANEL ...................................................................................................................... 46

F IGURE 9: D UAL SLOT FRONT PANEL ......................................................................................................................... 46

F IGURE 10: EIDE CONNECTOR LOCATION ................................................................................................................. 51

F IGURE 11: K EYBOARD & MOUSE CONNECTOR LOCATION ........................................................................................ 52

F IGURE 12: K EYBOARD & MOUSE CONNECTOR LAYOUT ........................................................................................... 53

F IGURE 13: E THERNET CONNECTOR LOCATION ......................................................................................................... 53

F

IGURE

14: E

THERNET CONNECTOR LAYOUT

............................................................................................................ 53

F IGURE 15: COM 1 LOCATION .................................................................................................................................. 55

F IGURE 16: VGA CONNECTOR LOCATION ................................................................................................................. 55

F IGURE 17: USB CONNECTOR LOCATION .................................................................................................................. 56

F IGURE 18: USB CONNECTOR LAYOUT ..................................................................................................................... 57

F IGURE 19: T EMPERATURE VS .

AIRSPEED .................................................................................................................. 80

F IGURE 20: C X 9 V2 COMPONENT SIDE PLACEMENT PLAN ......................................................................................... 83

F IGURE 21: C X 9 V2 SOLDER SIDE PLACEMENT PLAN ................................................................................................. 84

F IGURE 22: CTM12 COMPONENT LOCATIONS ........................................................................................................... 86

F IGURE 23: CTM12 E THERNET CONNECTOR LAYOUT ............................................................................................... 88

F IGURE 24: DVI CONNECTOR LAYOUT ...................................................................................................................... 91

F IGURE 25: P LACEMENT P LAN CTM12..................................................................................................................... 98

F

IGURE

26: M

OUNT

PMC

BOARD TO

C

X

9 ............................................................................................................... 100

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 20

List of Tables

T ABLE 1: S TYLES AVAILABLE ................................................................................................................................... 28

T ABLE 2: D ELIVERY VOLUME .................................................................................................................................... 29

T ABLE 3: L IST OF ACCESSORY OPTIONS ..................................................................................................................... 30

T ABLE 4: BIOS ID LINE ............................................................................................................................................ 40

T ABLE 5: B OOT TIMING ............................................................................................................................................. 43

T ABLE 6: S IGNAL NAME GROUPS .............................................................................................................................. 47

T ABLE 7: CPCI CONNECTORS .................................................................................................................................... 48

T ABLE 8: I/O CONNECTORS J7003 …5 .................................................................................................................... 49

T ABLE 9: EIDE CONNECTOR ..................................................................................................................................... 52

T ABLE 10: K EYBOARD & MOUSE PIN ASSIGNMENTS ................................................................................................. 53

T ABLE 11: E THERNET CONNECTOR PIN ASSIGNMENTS .............................................................................................. 54

T ABLE 12: E THERNET LED DISPLAY DEFINITIONS .................................................................................................... 54

T ABLE 13: COM 1 PIN ASSIGNMENTS ........................................................................................................................ 55

T

ABLE

14: VGA

CONNECTOR PIN ASSIGNMENTS

....................................................................................................... 56

T ABLE 15: USB CONNECTOR PIN ASSIGNMENTS ....................................................................................................... 57

T ABLE 16: PMC1 CONNECTOR PIN ASSIGNMENTS ..................................................................................................... 58

T ABLE 17: PMC2 CONNECTOR PIN ASSIGNMENTS ..................................................................................................... 59

T ABLE 18: M EMORY AREA ASSIGNMENTS ................................................................................................................. 61

T ABLE 19: S TANDARD REGISTER SET ........................................................................................................................ 62

T ABLE 20: I NTERRUPT ASSIGNMENTS ........................................................................................................................ 63

T ABLE 21: I NTERVAL TIMER FUNCTIONS ................................................................................................................... 66

T ABLE 22: P ARALLEL INTERFACE OPTIONS ............................................................................................................... 68

T ABLE 23: IPMB BACKPLANE PIN ASSIGNMENTS ...................................................................................................... 69

T ABLE 24: S UPPORTED OPERATING SYSTEMS ............................................................................................................ 70

T ABLE 25: SMB US DEVICES ...................................................................................................................................... 71

T

ABLE

26: P

OWER MANAGEMENT EVENTS

................................................................................................................ 72

T ABLE 27: BIOS POWER UP STATUS ......................................................................................................................... 74

T ABLE 28: P OWER CONSUMPTION CPU DEPENDENT ................................................................................................. 76

T ABLE 29: P OWER CONSUMPTION DRAM DEPENDENT ............................................................................................. 77

T ABLE 30: L ITHIUM BATTERY PARAMETERS ............................................................................................................. 78

T ABLE 31: E NVIRONMENT CONDITIONS .................................................................................................................... 79

T ABLE 32: S HOCK & VIBRATION PARAMETERS ......................................................................................................... 79

T ABLE 33: M AXIMUM HEIGHT USAGE ....................................................................................................................... 80

T

ABLE

34: P

OWER SUPPLY PARAMETERS

.................................................................................................................. 81

T ABLE 35: S UPPLY VOLTAGE RANGE ......................................................................................................................... 81

T ABLE 36: GPIO INPUT VOLTAGES ........................................................................................................................... 82

T ABLE 37: GPIO OUTPUT VOLTAGES ........................................................................................................................ 82

T

ABLE

38: CTM 12 EIDE

CONNECTOR

..................................................................................................................... 87

T ABLE 39: CTM12 E THERNET CONNECTOR PIN ASSIGNMENTS ................................................................................. 88

T ABLE 40: CTM12 E THERNET CONNECTOR LED ..................................................................................................... 89

T ABLE 41: P ARALLEL CONNECTOR PIN ASSIGNMENTS ............................................................................................... 89

T ABLE 42: COM1/COM2 CONNECTOR PIN ASSIGNMENTS ........................................................................................ 90

T ABLE 43: VGA CONNECTOR PIN ASSIGNMENTS ....................................................................................................... 90

T ABLE 44: DVI CONNECTOR DIGITAL PIN ASSIGNMENTS ........................................................................................... 91

T ABLE 45: DVI CONNECTOR ANALOG PIN ASSIGNMENTS .......................................................................................... 92

T

ABLE

46: USB

CONNECTOR

(10-

PIN HEADER

)

PIN ASSIGNMENTS

............................................................................ 92

T ABLE 47: F LOPPY CONNECTOR PIN ASSIGNMENTS ................................................................................................... 93

T ABLE 48: M ISCELLANEOUS CONNECTOR PIN ASSIGNMENTS .................................................................................... 94

T ABLE 49: PMC I/O ONBOARD PIM CONNECTOR PIN ASSIGNMENTS ........................................................................ 95

T

ABLE

50: PMC I/O 64-

PIN HEADER CONNECTOR PIN ASSIGNMENTS

........................................................................ 96

T ABLE 51: P OWER CONNECTOR PIN ASSIGNMENTS .................................................................................................... 97

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 21

T ABLE 52: P OWER IN/OUT CONNECTOR PIN ASSIGNMENTS ..................................................................................... 97

T ABLE 53: E LECTRICAL CHARACTERISTICS ............................................................................................................... 99

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 22

CHAPTER 1 Introduction

Chapter Scope

Board Design

Figure 1: Sample picture of Cx9 board

This chapter describes features, capabilities and compatibility of the CR9, CP9 and CT9 CompactPCI Single Board Computer. All three boards are based on the same PCB design. These three products will be referred to in this manual as the CX9 family. Any further specification in this document referring to Cx9 can be applied to CR9, CP9 and CT9 unless otherwise noted.

The Cx9 is a fully IBM-AT compatible stand-alone PC. It is equipped with many functions a conventional Personal Computer can only offer with several add-on cards. Extension boards can be connected via the CPCI interface. The minimized board size and the large number of interfaces and functions allow

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 23

the Cx9 to be used in many applications. See the following block diagram for the board design.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 24

Figure 2: Logical diagram of Cx9 board

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 25

Design Features

The Cx9 CompactPCI Single Board Computer features:

Microprocessor

Intel® Pentium® M processor 600 MHz to 1.8 GHz and higher,

Intel® Celeron® M processor 1.3 GHz

Chipset

Intel E7501 with ICH4 and a P64H2 PCI bridge

CMOS RAM

114 byte non-volatile RAM

MC146818 compatible RTC with onboard Lithium battery

EEPROM (Serial)

512 Bytes or 64 KBytes for user information

DRAM

256 MB to 2 GB DDR 200 MHz with ECC

Flash BIOS

Easy updating, in-system programmable

AMIBIOS

Intel Ethernet BOOT module

Keyboard/Mouse

IBM PC/AT compatible keyboard controller with PS/2 style connector

LCD/VGA

Version 2.x uses the NVIDIA® GeForce™ 420 Go series high performance graphics controller with integrated DDR memory 16 or 32 MBytes, max. resolution at DVI port 1024x768, at CRT 1600x1200

Version 3.x (RoHS version) uses the ATI Mobility™ Radeon™ graphics controller with 128/256 bit 2D, 3D and multimedia graphics accelerator, 16 MB to 64 MB DDR memory, max. resolution 1600 x 1200 analog and 1024 x 768

DVI

USB

One front and 4 rear USB 2.0 ports

Watchdog

Watchdog implemented in ICH4 chipset and National PC87417 Super I/O

High Resolution Timer

User programmable timer, allows ‘Real Time Functions’ implemented in chipset

Fast Ethernet

Two 10/100/1000BaseT high speed Ethernet channels either front or rear

(PICMG 2.16) with Intel 82546GB Ethernet controller

Hard/Flash Disk

Onboard mountable 2.5” IDE hard disk or Flash Drive

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 26

Floppy

Supported formats: 3.5 inch, 720 kBytes - 1.44 MBytes

EIDE/ATAPI

UDMA 100 EIDE/ATAPI interface within ICH4 with two IDE channels

(primary IDE off-board and secondary IDE on-board). Transfer rate with up to

100 MB/s, for two external devices (master/slave) and one onboard 2.5” hard/flash disk. The onboard (secondary) interface is limited in speed to

UDMA 2 (33.3 MB/s) because of cable/connector restrictions.

Serial I/O

National PC87417 Super I/O with two asynchronous 16550 compatible channels with 16 byte FIFO, Transfer rates up to 115.2 KBaud user selectable

RS232/422/485

Parallel I/O

Fully bidirectional IEEE 1284 enhanced parallel port support ECP and EPP modes

PMC slots

One 64 Bit/66 MHz (3.3 V IO voltage signaling) and one 32 Bit/33 MHz (5 V

IO voltage signaling) PCI mezzanine connector for standard PMC with front and rear I/O

I/O signals available at the rear connectors

With PCB version V2 the 64 bit PMC lot is PCI-X capable with 66/100/133

MHz

CPCI System slot

Up to 7 peripheral slots 64 Bit CPCI/33 MHz with Hint HB6 bridge (Up to 4 peripheral slots 64 Bit/66 MHz). Standard backplanes can be used. Onboard

Pullup resistors are optimized for 3.3 V I/O voltage, but 5 V I/O can also be used for 33 MHz.

CPCI I/O Slot

Cx9 works as peripheral board 64 Bit or 32 Bit with 66 MHz or 33 MHz and

Hot Swap functionality.

IPMI (CT9)

Hitachi controller for support of Intelligent Peripheral Management Interface.

Temperature Sensors

Measure temperatures of CPU-die and three onboard locations. The sensors are software readable in 1 °C increments from -55 °C to +125 °C.

Front panel I/O

2 x Ethernet, VGA, PMCI/O, COM1, KB/MS, USB1, Reset, 3xLED (blue: Hot

Swap; green, red: user definable) depending on the board configuration.

Back panel I/O

TMDS,VGA, LCD, IDE (Master/Slave), FDC, COM1-2, LPT, USB2-5, 2x

PMCI/O, KB, MS, speaker, reset, ext. Battery, SMBus, IPMB, GPIO[0...7], 2x

Ethernet. Transition modules with 1:1 PC compatible connectors are available.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 27

Power supply Usage

+5 V and +3.3 V for board supply

+12 V for PMC and Hot Swap controller supply

-12 V optional, if needed on PMC

Note:

The Cx9 boards shows a height violation which is to be checked if a PMC mezzanine module needs to be installed into the central area of the board

(PMC1).

Approval

Designed to meet standard UL1950, CE class A, FCC-A

H110 Backplanes

The CT9 can be optionally ordered without connector J7004 (=CPCI J4) assembled for backplanes providing H110 functionality. As a consequence some rear I/O will not be available. Please check in Chapter 4 in the Interfaces section for more details.

Styles available

Table 1: Styles available

Cx9 C D I H R N

1 2 3 4 6 8 x x x x x

x x x x

x

Conformal x x x x

Onboard battery x x x x

Onboard speaker x x x x

CT9 and CP9 can only be ordered in C-, 1- or I-, 3-style. x

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 28

CHAPTER 2 Unpacking and Inspection

Chapter Scope

This chapter covers the suggested inspection and preparation considerations and background information necessary prior to using the Cx9. Unpacking, initial inspection, and first-time operation of the Cx9 are covered. Following the procedures given in the chapter is recommended, since they will verify proper operation after shipping and before the product is integrated into your system.

Delivery Volume

Please check that the delivered package contains the following items:

Table 2: Delivery volume

Qty. Item Purpose

CP9 or

CT9

1 CDROM Technical Product Information with driver software and manuals in Adobe Acrobat

(PDF) format

The manual files are also available through the World Wide Web from our

Web-Server: http://www.sbs.com

Available Accessories

The following table lists accessory options which are available for the Cx9:

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 29

ESD

Table 3: List of accessory options

Item Purpose

ZKAAPS2SPLIT Front panel Y-cable for keyboard and mouse

CTM12 Transition module, 6U x 4HE/HP

VGA2DVI DVI to standard VGA converter

Please contact the sales department or your sales representative for latest information on options and accessories.

Accessories are subject to change without notice.

Electrostatic Discharge Notice

The discharge of static electricity, known as Electro Static Discharge or ESD, is a major cause of electronic component failure. The Cx9 has been packed in a static-safe bag which protects the board from ESD while the board is in the bag.

Before removing the Cx9 or any other electronic product from its static-safe bag, be prepared to handle it in a static-safe environment.

Warning

You should wear a properly-functioning antistatic strap and ensure you are fully grounded. Any surface upon which you place the unprotected Cx9 should be static-safe, usually facilitated by the use of antistatic mats. From the time the board is removed from the antistatic bag until it is in the card cage and functioning properly, extreme care should be taken to avoid ‘zapping’ the board with ESD. You should be aware that you could ‘zap’ the board without you knowing it; a small discharge, imperceptible to the eye and touch, can often be enough to damage electronic components. Extra caution should be taken in cold and dry weather when static easily builds up.

Only after ensuring that both you and the surrounding area are protected from

ESD, carefully remove the board or module from the shipping carton by grasping it by the front panel and the connectors. Place the board, in its antistatic bag, flat down on a suitable surface. You may then remove the board from the anti static bag by tearing the ESD warning labels.

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 30

Initial Inspection

Unpacking

Notes:

Drain static electricity before you install or remove any parts. Installing or removing modules without observing this precaution could result in damage to this and/or other modules in your system.

After unpacking the Cx9, you should inspect it for visible damage that could have occurred during shipping or unpacking. If damage is observed (usually in the form of bent component leads or loose socketed components), contact SBS

Technologies for additional instructions. Depending on the severity of the damage, it may need to be returned to the factory for repair. DO NOT apply

power to the board if it has visible damage. Doing so may cause further, possibly irreparable damage, as well as introduce a fire or shock hazard. Since the Cx9 incorporates a number of socketed components, including the CPU, memory, etc., these should be inspected to make sure they are seated fully in their sockets.

Since some of the boards or modules incorporate a number of socketed components, including the CPU, memory, etc., these should be inspected to make sure they are seated fully in their sockets.

Note

Please observe all safety procedures to avoid damaging system and protect operators and users.

Please read the manual carefully before unpacking the board or module or fitting the device into your system. Also adhere to the following:

• Please read this manual carefully before unpacking the module or fitting it into your system. This will certainly save time and avoid trouble.

• Observe all precautions for electrostatic sensitive modules

• If the product contains batteries, please do not place the board on conductive surfaces, antistatic plastic, or sponge, which can cause shocks and lead to battery or board trace damage.

• Please do not exceed the specified operational temperatures. Note that batteries and storage devices might also have temperature restrictions.

• Keep all original packaging material for future storage or warranty shipments of the board.

Although the Cx9 is carefully packaged to protect it against the rigors of shipping, it is still possible that shipping damages can occur. Careful inspection of the shipping carton should reveal some information about how the package was handled by the shipping service. If evidence of damage or rough handling is found, you should notify the shipping service and SBS Technologies as soon as possible.

Retain all packing material in case of future need.

Note

Before installing or removing any board, please ensure that the system power and external supplies have been turned off.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 31

Handling

Figure 3: Board packaging

Proper handling of the Cx9 is critical to ensure proper operation and long-term reliability. When unpacking the board, and whenever handling it thereafter, be sure to hold the board by the front panel or the card ejectors as shown in the drawing on the left. Do not hold the board by the circuit card edges, the heat sink, or the connectors.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 32

Figure 4: Handling the Cx9 board

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 33

CHAPTER 3 Installation

Chapter Scope

This chapter covers the installation of the Cx9 CompactPCI Single Board

Computer in a CompactPCI backplane and initial power-on operations.

Installation preparation

Use the following steps to install your SBS Technologies hardware.

• Before installing or removing any board, please ensure that the system power and external supplies have been turned off.

• Check that the jumpers and mezzanines are correctly configured for your application.

• Mount the board/mezzanine/transition module very carefully. See also additional advisories for VMEbus and CompactPCI products below.

• Connect all IO cables.

• Once you are certain that all modules are correctly fitted into the system and all connections have been made properly, restore the power.

General Advisories

Before installing or removing any board, please ensure that the system power and external supplies have been turned off.

Check that jumpers and mezzaniness are correctly configured for your application. Mount the board, mezzanine, or transition module very carefully.

See also sections on additional advisories below.

Do not restore power until you are sure that all modules are fitted correctly and all connections have been made properly.

Advice on CompactPCI products

Mount the CPU board carefully on the first CPCI bus slot (called system slot).

Note that on some boards connectors are used for IO purposes which must not

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 35

Required items

be inserted into a CPCI bus backplane. A transition module must be used instead.

Because the board is available in several options the description in this chapter is related to the standard configuration.

Note:

Make sure that the card ejectors are closed and the Hot Swap LED (blue) is

OFF.

The following items are required to start the Cx9 in a standard configuration:

Backplane and Power Supply

You will need a standard CompactPCI backplane wired into a regulated power supply capable of providing stable low noise +5 V, +3.3 V and +12 V sources.

Make sure that the supply is capable of meeting the total power requirements of

the Cx9. Please refer to chapter ‘Specifications’ on page 75 for details.

The Cx9 features Full Hot Swap capabilities according to the PCI Hot Plug specification PICMG 2.1. This allows orderly insertion and extraction of the board from the system host (backplane) without having to power down the system. Please note that this feature requires that Hot Swap functions are also

available on the backplane. See chapter ‘Hot Swap’ on page 70 for details.

Initially, you may plug the Cx9 into your 6U system slot of your CPCI system.

Optionally, when used as an intelligent peripheral board, the Cx9 can also be used in a non-system slot. In case that the Cx9 is used in a non-system slot you have to have an additional CPU board in the system slot for providing system clock, arbiter function and more. Please make sure that you do not have the power supply turned ON when the Cx9 is plugged into your backplane.

Keyboard and Mouse

You should have a compatible keyboard for initial system operation.

Depending on your application, this keyboard may be a standard full-travel keyboard, or one which utilizes membrane switches for harsh environments.

The miniature DIN keyboard connector is located on the front panel and is directly compatible with existing compliant keyboards. If your keyboard has the normal IBM PC-type keyboard connector you will need to use a cable adapter. This cable adapter is not delivered by SBS, but available on the shelf.

The connector is defined for both keyboard and mouse. SBS delivers a split adapter cable for keyboard and mouse, which has to be ordered separately. Plug this adapter cable ZKAAPS2SPLIT (Y form) into the keyed PS/2 connector on the front panel, then plug the keyboard and mouse into the adapter. If the adapter is not used, only a keyboard can be connected.

Plugging and unplugging a PS/2 keyboard or mouse while power is applied is not recommended and can cause software failure or damage to the PS/2 device and/or on-board circuitry. For proper function please use the split adapter delivered by SBS.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 36

Video Monitor

Any VGA-compatible video monitor can be used initially for display output.

The Cx9 offers front access to the video. Video can also be accessed via the J5

CPCI connector on the rear I/O side. In order to get access to these pins it is necessary to use a transition module.

Advice on Batteries

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by SBS Technologies.

Dispose of used batteries according to instructions of SBS Technologies and applicable local regulations.

Installation of a plug-in board

Boards are installed in a CPCI or VMEbus chassis by carefully sliding them into the guide rails, inserting them all the way until the handles can be operated to seat and lock the board in place. Handles typically have a lock (snap lever) to unlock them when extracting a board. Older boards may have screws instead of handles to secure the board in place.

Figure 5: 6U board insertion into system box

Installation of a plug-on module (mezzanine)

After making sure that you have installed the mezzanine properly onto your carrier board and installed both properly into a system shelf (subrack, card cage, enclosure), apply power to your system. When the board is completely reset, the processor should begin executing initial BIOS-resident routines indicated by the on-board status LED blinking red.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 37

Figure 6: Installing a PMC on a 6U CPCI carrier board

Note:

The carrier board might be of different size, like 6U (as shown here) or 3U or other form factor. It may conform to different board architectures, like CPCI

(as shown here) or VMEbus or other architecture.

Installation of the Rear Transition Module CTM12

The CTM12 is a 6U x 80 mm rear I/O module which has to be plugged into the

Cx9 separated by the backplane. This transition module has a DVI-I connector.

If necessary you need an external adaptor to be fully compatible with the VGA standard connector and pin assignments. On the transition module you either can connect a DVI panel or a standard VGA Monitor, but not both at the same time.

Plug your video monitor into this connector. Make sure that your selected chassis supports this type of rear I/O transition module.

After making sure that you have installed the Cx9 properly into your CPCI backplane, apply power to your video monitor and then the CPCI supply. When the board is completely reset, the processor should begin executing initial

BIOS-resident routines.

Note:

Make sure that the card ejectors are closed and the Hot Swap LED (blue) is

OFF.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 38

Note:

If the Cx9 was ordered without video on board, you can use an external video

CompactPCI card or a video PMC module. Consult the technical descriptions of these boards for required voltage and power consumption in the system.

Or use a terminal on COM1. Provide Port Settings – Bits, Data Bits, Parity and

Stop Bit.

Initial Power-On Operation

After some seconds, the Cx9 system BIOS banner will display on the and the red LED on the front will get non-blinking green.

If you have seen all the messages to this point, you can be confident that the board is running properly and is ready to be installed and setup for your application.

Entering the BIOS SETUP

To enter SETUP during the initial power-on sequence press the DELETE key during the boot up sequence. Check the on-screen messages. This tells you when you can enter the BIOS by pressing the DELETE key. If this message does not appear on your monitor, just press the DELETE key when you hear short beeps indicating the keyboard was initialized. You may also press the

DELETE key when the LED goes from blinking orange to blinking green.

Consult the 'AMI-BIOS for CR9, CP9, CT9 User’s and Programmer’s Manual' for further information on how to change settings and configurations.

If the board does not perform as described above, some damage may have occurred in shipping or the board is not installed or setup properly. Contact

SBS technical support as described in chapter ‘Support, Service, and Warranty

Information’ for further instructions.

If the BIOS setup is wrong in the CMOS RAM, then please press the

‘0/INS’key or the ‘INS’ key during boot up. This clears the CMOS settings and stops the video output at an early stage. There you can also see the BIOS ID line:

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 39

Example/coding of the ID line:

Table 4: BIOS ID line

62 – 0102 – 004199 – 00101111 – 071595 - E7501 – CR9– Y2KC-0 supplier major & minor BIOS revisions processor, flash ROM size

AMIBIOS core copyright date year 2000 compliant project

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 40

CHAPTER 4 Getting Started

Chapter Scope

This chapter gives some useful tips when using a board from Cx9 family the first time. It might be also useful to read this chapter carefully, when problems came up in using the Cx9.

Power Supply

All boards of the Cx family require up to 50 Watts from the power supply. For exact values please check the actual datasheet, but for rough data a current of up to 7 A at the 5 V rail and 12 A at the 3.3 V rail must be taken into consideration. The +12 V must only supply a few mA and is not very critical. If there are harddisc or PMC modules attached to the Cx9, then their power consumption must also be calculated. Keep in mind, that standard power supplies often require minimum loads on every supply voltage fro proper operation. It might be necessary to add a load to the +12 V to ensure correct voltage levels on 3.3 V and 5 V.

If you ever see the board not starting well or doing resets at random states, please check the voltage of the three supply voltages at the backplane. When measuring there, you can use a standard digital multimeter and you have to attach it to the backplane at positions where no high current is flowing. So better use rear contacts of the bus connectors or unused power connectors to measure, because measuring the voltages at the used power connectors can result in wrong values, which are caused by the high current flowing.

The +12 V are less critical, but 5 V and 3.3 V should reach their nominal value when measuring with a multimeter. If the voltages are less than 5.0 V or 3.3 V, then short voltage drops while the CPU or memory gets into high activities may result in resetting the Cx9 board.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 41

Status indicator, Postcode and Beeps

The Cx9 family has a dual color LED at the front panel for a quick status indicator usage. The possible colors are red, orange or green and the LED can blink in different frequencies or be on continuously.

The CR9, CP9, CT9 additional have a blue Hot Swap LED as required according to the PICMG specification. This blue LED is also an indication for a reset condition.

While running its BIOS initialization all boards of the Cx9 family write postcodes (POST = Power-On Self Test) to port 80h at the PCI bus 0 (at

PMC2). These accesses can be monitored with appropriate equipment or a

PMC post card. For easier access the postcodes are sent also to the parallel port

LPT1 data lines. When measuring their values or adding 8 LEDs with current limiting resistors to GND, you can follow the POST sequence of the BIOS.

When the boot process stops at a certain point also the eight voltage levels can be measured with a multimeter.

• Currently some more debug support is integrated on the Cx9 family, which beeps the postcode if the POST stops before the CRT is initialized. This

POST beep support can be removed at a later development stage, if the required space within the onboard programmable logic is no longer available, so don’t rely on this. The beeps are long for a ‘1’ and short for a

‘0’. They start with the highest bit 7 and beep 8 represents the lowest bit 0.

After some seconds the beep sequence is repeated for an easier recognition.

If the beep code is not repeated, then this beeps are issued within the BIOS execution to show some other failures (i.e. fails in memory detection or if no VGA is detected). For more information please check the AMIBIOS8

Check Point and Beep Code List as well as the AMIBIOS8 Error

Messages.

Booting

When switching-on the Cx9 following steps are done by hardware:

- On the CR9 family, all voltages at the backplane are observed until they reach a first trip point which is 2.5 V at the 5 V/3.3 V rails and 9.5 V at the +12 V rail.

After this the onboard voltages are controlled raised up to the external supplied value

- The continuous red Status LED shows that all circuitry is in reset

- All onboard DC/DC converters are ramped up

- If all onboard supply voltages are at their correct values, the ‘power good’ status is acknowledged to all onboard devices and the red LED is switched off

- On the CR9 family, the blue Hot Swap LED is switched off when the onboard

PCI reset is released. Especially when the battery is removed, this can take a few seconds to start the 32 kHz Oscillator. The PCI reset gets inactive after this period.

- After this the CPU start reading it first instructions from BIOS. Very soon the red LED is programmed to a red blinking state and the first postcode is issued

- If the CPU does not start correctly, the red LED keeps off until the hardware watchdog will issue a further reset 1.6 seconds later. You can see this at the red

LED, which is on again for a short moment (at the CR9 family also the blue

LED). This sequence continues until the CPU starts correctly.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 42

Setup

For reference the complete BIOS boot sequence is shown with the current

BIOS version. This version is a rather early one and hopefully some of the long periods will speed up. The times depend mainly on the memory size and they are measured with 1 GB and quick boot enabled. Some of the postcodes are 16 bit, but only the lower 8 bits can be seen at the parallel port data lines. All postcodes are shown in hex.

Table 5: Boot timing

Time after releasing

PCI reset

1 µs

726 ms

3.9 s *1

8.4 s

12.2 s

12.3 s

12.7 s

15.2 s

D0

AC

D4

D6

D7

03

4013

202A

Comment

Red 1 Hz blinking

Orange 1 Hz blinking All memory is initialized

Green 1 Hz blinking Keyboard enabled *2

Green 2 Hz blinking

Video Bios is started

*3

16.9 s

17.2 s

17.2 s

17.3 s

3C

78

8C

00

Green 3 Hz blinking

Starting external

BIOS *4

Green 4 Hz blinking

Green steady on Try booting from mass storage

*1 from here add 2.9 seconds for 2 GBytes of memory

*2 now is the right point to press DEL if you want to go to BIOS SETUP

*3 CRT and/or panel are now initialized and show the startup screen.

*4 external BIOS from add on cards i.e. SCSI

Depending on the monitor/display type it may need some additional seconds until you can see something on the screen

When you want to enter the BIOS Setup, you have to press the keyboard ‘DEL’ key at the right moment. Especially when using a slow starting monitor it might be too late to wait for the CRT to show the message ‘Press DEL to enter Setup’.

Better look for the LED and press ‘DEL’ as soon as the LED goes from orange to green blinking. When you are using add on cards with external BIOS, you can hit the DEL key while their BIOS runs (i.e. SCSI BIOS device scan).

When you miss the right moment to press the DEL key, please use the reset button on the front panel to restart the power up sequence or switch off the power supply for a few seconds and restart it. With the current BIOS pressing the Ctrl-Alt-Del key combination at this boot-moment will result in switching to the next bootable device and try to boot from this. This feature cannot be disabled within Setup.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 43

Hot Swap on Cx9

Unexpected Resets

The Cx9 family supports full Hot Swap according to CPCI specification 2.1.

This includes all hardware functionality to detect other bus cards or devices to be plugged in or removed while the system is running under power. Also the

Cx9 can be hot plugged to a running system or be removed from it.

The necessary software/driver and operating system handling is not done within the BIOS of the Cx9, because all the tasks to recognize new inserted boards, to re-enumerate the PCI memory space while other cards/transfers are still running, cannot be done within BIOS. These tasks have to be fully done from the used operating system. Currently SBS Technologies have no drivers to support these functionalities.

The handling of the blue LED is also done within the necessary drivers. So do not expect the blue LED to go on and off according to the CPCI specification if no driver is loaded.

Whenever the Cx9 unexpectedly issues a reset and starts booting again, you may want to know the reset source. For this reason a set of special registers is implemented onboard. Every reset source set there a special bit and can be read in the next boot up. The register description can be found in the ‘Board Specific

Hardware Programmer’s Manual’.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 44

CHAPTER 5 Interfaces

Chapter Scope

This chapter describes the interfaces of the Cx9 CompactPCI Single Board

Computer located on the board and on the front panel. Each section on a particular interface includes a graphics illustration of the connector and a pin assignment table as well as notes on certain signal line characteristics, if necessary.

For interfaces of the transition module, please refer to the appropriate chapters found in the ‘Appendices’ to this manual.

Figure 7: Location of components on board and front panel

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 45

Front Panel Interfaces

Refer to the next drawing for the location of interfaces on the front panel of the

CR9 and CT9 single slot board (either with front I/O or with dual PMC):

Figure 8: Single slot front panel

This drawing indicates the location of interfaces on the front panel of the CP9 dual slot board:

Cx9 Connectors

Figure 9: Dual slot front panel

This chapter describes connector pin assignments on the Cx9. A pin assignment description for available transition module can be found in the corresponding appendix chapters.

CPCI connector reference

The CPCI specification numbers the CPCI connectors from bottom to top J1,

J2, J3, J4, and J5. The CPCI connectors on the Cx9 are J7001, J7002, J7003,

J7004, and J7005 respectively.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 46

Table 6: Signal name groups

Determiner Signal groups floppy disk controller signals hard disk controller signals

Parallel port

COM1, COM2 signals

VGA signals

Universal Serial Bus

\FD....

HD.... and \HD....

L1... and \L1....

C1....., C2.....

VGA…

USB… keyboard signals mouse signals

LCD signals

LAN signals

KB…

MS…

TX…

RJ…

SMB (I2C-Bus) SMB…

IPMI IPMI…

Misc. signals \SPEAKER

\RST_BUT

VBATIN

PMC IO Signals PMC...

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 47

CompactPCI bus Connector J7001 and J7002

This interface is used for connection to a standard CPCI backplane.

Table 7: CPCI connectors

20 GND NC GND

SMB_SCL d

SMB_ALRT#GND

17 NC GND \PRST \REQ6 \GNT6 GND

NC NC \DEG GND NC GND

15 NC GND \FAL \REQ5 \GNT5 GND

AD35 AD34 AD33 GND AD32 GND

13 AD38 GND VIO AD37 AD36 GND

AD42 AD41 AD40 GND AD39 GND

11 AD45 GND VIO AD44 AD43 GND

AD49 AD48 AD47 GND AD46 GND

9 AD52 GND VIO AD51 AD50 GND

8 AD56 AD55 AD54 GND AD53 GND

7 AD59 GND VIO AD58 AD57 GND

6 AD63 AD62 AD61 GND AD60 GND

5 C/\BE5 \64EN VIO C/\BE4 PAR64 GND

3 CLK4 GND \GNT3 \REQ4 \GNT4 GND

2 CLK2 CLK3 \SYSEN \GNT2 \REQ3 GND

1 CLK1 GND \REQ1 \GNT1 \REQ2 GND

24 AD01 +5V

ENUM +3.3V

LVIO

23 +3.3V AD04 AD03

AD00 \ACK64

L+5V AD02 GND

22 AD07 GND L+3.3V AD06 AD05 GND

21 +3.3V AD09 AD08 M66EN C/\BE0 GND

20 AD12 GND VIO AD11 AD10 GND

18 \SERR GND +3.3V PAR C/\BE1 GND

16 \DEVSEL

IPMB_SDA \PERR GND

VIO \STOP \LOCK GND

9 C/\BE3 IDSEL AD23 GND AD22 GND

8 AD26 GND VIO AD25 AD24 GND

7 AD30 AD29 AD28 GND AD27 GND

L+3.3V CLK0 AD31 GND

NC NC \RST GND

\HEALTHY LVIO INTP NC GND a

3 \INTA \INTB \INTC L+5V \INTD GND

1 +5V GND

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 48

J7003 A a

On long backplane pins for early power supply b

The VIO signals are not used by the Cx9. They are either 5 V or 3.3 V, depending on backplane c

These signals are not used on the Cx9 d

These SMBus signals are not supported by the IPMI controller on the CT9

I/O Connector J7003, J7004, and J7005

The connector J7004 is not mounted on the CT9, if the H110-Bus is used on the backplane. For easy use a transition module is available from SBS

Technologies to connect the I/O-Connectors with standard connectors.

Table 8: I/O connectors J7003 - …5

B C D E F

18 LPA_DA+ LPA_DC+ LPA_DC- GND

17 LPA_DB+ LPA_DB- GND LPA_DD+

16 LPB_DA+ LPB_DA- GND LPB_DC+ LPB_DC- GND

15 LPB_DB+ LPB_DB- GND LPB_DD+ LPB_DD- GND

14 VCC3 VCC3 a

VCC3 a

VCC a

VCC a

GND

13 PMC1IO_05 PMC1IO_04 PMC1IO_03 PMC1IO_02 PMC1IO_01 GND

12 PMC1IO_10 PMC1IO_09 PMC1IO_08 PMC1IO_07 PMC1IO_06 GND

11 PMC1IO_15 PMC1IO_14 PMC1IO_13 PMC1IO_12 PMC1IO_11 GND

10 PMC1IO_20 PMC1IO_19 PMC1IO_18 PMC1IO_17 PMC1IO_16 GND

9 PMC1IO_25 PMC1IO_24 PMC1IO_23 PMC1IO_22 PMC1IO_21 GND

8 PMC1IO_30 PMC1IO_29 PMC1IO_28 PMC1IO_27 PMC1IO_26 GND

7 PMC1IO_35 PMC1IO_34 PMC1IO_33 PMC1IO_32 PMC1IO_31 GND

6 PMC1IO_40 PMC1IO_39 PMC1IO_38 PMC1IO_37 PMC1IO_36 GND

5 PMC1IO_45 PMC1IO_44 PMC1IO_43 PMC1IO_42 PMC1IO_41 GND

4 PMC1IO_50 PMC1IO_49 PMC1IO_48 PMC1IO_47 PMC1IO_46 GND

3 PMC1IO_55 PMC1IO_54 PMC1IO_53 PMC1IO_52 PMC1IO_51 GND

2 PMC1IO_60 PMC1IO_59 PMC1IO_58 PMC1IO_57 PMC1IO_56 GND

1 PMC1VIO PMC1IO_64 PMC1IO_63 PMC1IO_62 PMC1IO_61 GND

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 49

J7004 A B C D E F

25 NC

24 NC

USB3- USB2-

23 \FD_DRVO GND

GND

16 \L_PE \L_SLIN \L_INIT

12-14 KEY KEY KEY KEY KEY KEY

11 \VCCOFF NC VBATIN

10 NC NC NC \RST_BUT

GND

GND

9 NC NC NC GPIO2

8 NC NC NC GPIO4

7 NC NC NC GPIO6

6 NC NC NC GND GND GND

5 \M1LINK1000 GND

\M2LINK GND

2 \M1ACT \M2ACT GND

VCC3 a

VCC a

VCC a

-12V GND a

. for internal use only.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 50

J7005 A B C D E F

22 PMC2IO_05 PMC2IO_04 PMC2IO_03 PMC2IO_02 PMC2IO_01 GND

21 PMC2IO_10 PMC2IO_09 PMC2IO_08 PMC2IO_07 PMC2IO_06 GND

20 PMC2IO_15 PMC2IO_14 PMC2IO_13 PMC2IO_12 PMC2IO_11 GND

19 PMC2IO_20 PMC2IO_19 PMC2IO_18 PMC2IO_17 PMC2IO_16 GND

18 PMC2IO_25 PMC2IO_24 PMC2IO_23 PMC2IO_22 PMC2IO_21 GND

17 PMC2IO_30 PMC2IO_29 PMC2IO_28 PMC2IO_27 PMC2IO_26 GND

16 PMC2IO_35 PMC2IO_34 PMC2IO_33 PMC2IO_32 PMC2IO_31 GND

15 PMC2IO_40 PMC2IO_39 PMC2IO_38 PMC2IO_37 PMC2IO_36 GND

14 PMC2IO_45 PMC2IO_44 PMC2IO_43 PMC2IO_42 PMC2IO_41 GND

13 PMC2IO_50 PMC2IO_49 PMC2IO_48 PMC2IO_47 PMC2IO_46 GND

12 PMC2IO_55 PMC2IO_54 PMC2IO_53 PMC2IO_52 PMC2IO_51 GND

11 PMC2IO_60 PMC2IO_59 PMC2IO_58 PMC2IO_57 PMC2IO_56 GND

9 C1 _ DCD/TXD- C1 _ DSR/TXD+ \PHD_CS0 \PHD_IOR \PHD_IOW GND

8 C1 _ RXD/RTS C1 _ RTS/RTS+ PHD_A0 PHD_D08

-

7 C1 _ TXD/CTS+ C1 _ CTS/CTS

-

6 C1

+

_ DTR/RXD

PHD_IRQ PHD_D09 PHD_D06 GND

C1 _ RI/RXD- PHD_RDY PHD_D10 PHD_D05 GND

5 C2 _ DCD/TXD- C2 _ DSR/TXD+ \PHD_DAK PHD_D11 PHD_D04 GND

4 C2 _ RXD/RTS C2 _ RTS/RTS+ PHD_DRQ PHD_D12 PHD_D03 GND

-

3 C2 _ TXD/CTS+ C2 _ CTS/CTS \PHD_CS1 PHD_D13 PHD_D02 GND

2 C2 _ DTR/RXD

+

-

\PHD _ RST PHD_A2 PHD_D14 PHD_D01 GND

1 C2 _ RI/RXD- \PHD _ PDIAG PHD_A1 PHD_D15

EIDE Connector P1800

The EIDE interface is designed as a 44-pin 2 mm pitch male onboard connector

P1800 to fit directly to a 2,5-inch EIDE hard drive or flash disk. P1800 is the secondary EIDE interface of the onboard EIDE controller.

Figure 10: EIDE connector location

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 51

Table 9: EIDE connector

Name P1800 Name

HD_D8 4 3 HD_D7

HD_D9 6 5 HD_D6

HD_D10 8 7 HD_D5

HD_D11 10 9 HD_D4

HD_D12 12 11 HD_D3

HD_D13 14 13 HD_D2

HD_D14 16 15 HD_D1

HD_D15 18 17 HD_D0

HD_A2 36 35 HD_A0

\HD_CS1 38 37 \HD_CS0

GND 40 39 DASP

+5V 42 41 +5V

Keyboard and PS/2 Mouse Interface P2001

The Cx9 allows an easy adaptation of a keyboard to a standard 6-pin MINIDIN connector. Also a PS/2 mouse can be connected directly or via an external cable splitter.

Figure 11: Keyboard & mouse connector location

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 52

Figure 12: Keyboard & mouse connector layout

Table 10: Keyboard & mouse pin assignments

Name P2001

Keyboard Data

Mouse Data

1

2

GND 3

Fused +5 V

a

4

Keyboard Clk 5

Mouse Clk 6 a

the Fused +5 V pin is fused with a 2 A fuse. For normal operation don’t exceed 100 mA current. The used fuse does automatically recover if the over current is resolved.

Ethernet Interface U5600 and U5650

The Ethernet output front or rear can be selected via order. When ordered with front option, the connectors are located in the front panel.

Figure 13: Ethernet connector location

LED 1 LED 2

Figure 14: Ethernet connector layout

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 53

Table 11: Ethernet connector pin assignments

Name 10/100base Name 1000base Ethernet1, 2

NC

LP_DD+ 7

NC

LP_DD- 8

Two LED’s (LED1-green and LED2-yellow) are integrated in each of the RJ45 connector. These LED’s indicate the link status and activity of the interfaces.

Table 12: Ethernet LED display definitions

LED1 green Function

On Link

LED2 yellow Function

On, blink Tx/Rx activity

Off No activity

The pin assignment at the rear I/O is compliant with the PICMG 2.16

(Switched Packet Backplane) specification. The Ethernet interface can also be accessed via the CTM12 transition module (see Appendix A) for connector type and pin assignment.

Serial Port COM1 P2201

The Cx9 offers two RS232 serial ports. All COM ports are accessible via the transition module, and additionally COM1 is accessible via the front panel connector.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 54

Figure 15: COM 1 location

COM1, 2 are software selectable for RS-232 or RS-422/485 operation within

BIOS setup. The RS485 output drivers can be enabled or disabled with the

DTR signal. An active DTR means the drivers to be enabled. When using the

RS422 setting the output drivers are always enabled and the DTR signal is not used.

Table 13: COM 1 pin assignments

Name RS232 Name RS422/485 P2201

DCD TXD- 1

RXD RTS- 2

TXD CTS+ 3

CTS CTS- 8

GND GND 5

VGA Interface P4200

The monitor signals are available at the front panel on a standard 15-pin female

D-Sub connector.

Figure 16: VGA connector location

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 55

Table 14: VGA connector pin assignments

Name P4200

RED 1

GREEN 2

BLUE 3

HSYNC 13

VSYNC 14

DDC-Data 12

DDC-Clock 15

Fused +5 V a

9

GND 5, 6, 7, 8, 10 a

the Fused +5 V pin is fused with a 2 A fuse. For normal operation don’t exceed 100 mA current. The used fuse does automatically recover if the over current is resolved.

USB Interfaces P1680

One USB channel is available at the front panel and four USB devices are available on rear IO.

Figure 17: USB connector location

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 56

Figure 18: USB connector layout

Table 15: USB connector pin assignments

Name P1680

Fused +5 V

a

1

USB0- 2

USB0+ 3

GND 4 a

the Fused +5 V pin is fused with a 2 A fuse. For normal operation don’t exceed 100 mA current. The used fuse does automatically recover if the over current is resolved.

PMC1 Connectors P6201, P6202, and P6203

The following table lists the pin assignments of the onboard PMC1 connector.

The PMC1 slot is 64 bit and 66 MHz capable and works with the internal second PCI bus of the P64H2 PCI Bridge. If an installed PMC card operates at

33 MHz only the PCI bus speed is reduced to 33 MHz. With board revision V2 and higher, this slot is PCI-X capable with 66/100/133 MHz. The PMC is electrical and mechanical compliant to the specification IEEE 1386 and 1386.1

(check for possible height incompatibility in ‘Features’ and ‘Specifications’ sections of this manual) with enhancements of the Processor PMC Standard

VITA 32-2003. The enhancements provide pins for a second device (IDSELB and REQB/GNTB) but don’t support a monarch PMC card.

The PCI signaling voltage is fixed to 3.3 V. Nevertheless PMC cards with

3.3 V or 5 V supply voltage can be used on this PMC slot.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 57

Table 16: PMC1 connector pin assignments

-12 GND

PCIIRQ5# NC C/BE6 05 06 PCIIRQ6# GND C/BE5

PRESENT# GND C/BE4 07 08 +5

PCIIRQ7# Reserved V(I/O) 09 10 Reserved

GND PUP AD63 11 12 NC

PCICLK PCIRST# PDN

GND +3.3 GND

GND

+5 GND AD58

V(I/O)

GND +3.3 AD54

(IDSEL)

30 V GND AD50

FRAME# GND GND 33 34 GND AD30

(IDSELB)

AD48

DEVSEL# GND AD45 37 38 +5 STOP# GND

PCIXCAP PERR# V(I/O) 39 40 LOCK# GND AD44

Reserved +3.3 SERR# AD42

AD6 +3.3 AD35

V(I/O) NC V(I/O)

AD0 ACK64# Reserved 61 62 +5 V +3.3 V GND a

Weak 10k

Ω pull-down (PDN) to GND and pull-up (PUP) to VIO.

)

Reserved

V(I/O)

-12 V

Reserved. Do not connect anything

I/O Voltage, connected with +3.3 V

Only available if connected at the CPCI backplane.

PMC2 Connectors P7201, P7202

PMC2 is available on a CR9 and CT9 without the front Ethernet and/or front

VGA connector. On a CP9 PMC2 is available in the second slot

The following table lists the pin assignments of the PMC2 connector. The PMC slot is 32 bit and 33 MHz capable and works with the internal primary PCI bus of the I/O Controller Hub.. The PMC is electrical and mechanical compliant to the specification IEEE 1386 and 1386.1 with enhancements of the Processor

PMC Standard VITA 32-2003. Check for possible height incompatibility in

‘Features’ and ‘Specifications’ sections of this manual. The enhancements

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 58

provide pins for a second device (IDSELB and REQB/GNTB) but don’t support a monarch PMC card.

The PCI signaling voltage is fixed to 5 V for this PMC2. Nevertheless PMC cards with 3.3 V or 5 V supply voltage can be used on this PMC slot.

Table 17: PMC2 connector pin assignments

PCIIRQ7# NC

PRESENT# GND 07 08 +5 Reserved

PCIIRQ5# Reserved 09 10 Reserved Reserved

GND PUP

a

11 12 NC +3.3

13 14 GND PDN

a

PDN

a

REQ0# PME# 17

V(I/O) AD30 19 20 AD31 AD29

(IDSEL)

AD22 +3.3 27

FRAME# GND 33 34 GND AD29

(IDSELB)

DEVSEL# GND 37 38 +5 STOP#

Reserved +3.3 SERR#

AD9 AD8 49 50 +5 V +3.3 V

AD2 GND

61 62 +5 V

PUP

+3.3 V

NC a

Weak 10 k

Ω pull-down (PDN) to GND and pull-up (PUP) to VIO.

)

Reserved Reserved. Do not connect anything

V(I/O) I/O Voltage, connected with +5 V

-12 V Only available if connected at the CPCI backplane.

PMC-I/O Connector P6204 and P7204

Pin 1 of the I/O connector is PMCxIO_01; Pin 2 is PMCxIO_02 and so on. The x denotes PMC1 or PMC2 respectively. All traces are not connected to any

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 59

Transition Module signal onboard and no pairs or length adjusted traces are used to route this signals to the backplane connectors.

Please refer to the appendix chapters for interface location and connector pin assignments for the optional extension boards and transition modules.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 60

CHAPTER 6 Resources

Chapter Scope

This chapter describes system resources, such as memory mapping, register set and default interrupt request assignments.

Memory Map

The table below shows the memory address area used by the Cx9.

Table 18: Memory area assignments

Address Size Used by

$00000 - $9FFFF

$A0000 - $BFFFF

$C0000 - $DFFFF

640 kBytes

128 kBytes

128 kBytes

$E0000 - $FFFFF

$FFF80000 -

$FFFFFFFF

128 kBytes

$100000 - $3FFFFFFF Depends on avail.

DRAM

$4000000 -

$FFFBFFFF

Depends on avail.

DRAM

512 kBytes

System RAM

Video RAM (if enabled)

Used by PCI ROMs:

VGA, SCSI, Ethernet

System BIOS

Extended RAM

Dynamically used by PCI devices

System BIOS

Register Set

The following section provides an overview of the registers located in the I/O address area of the Cx9.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 61

Note:

The address location of PCI devices such as SCSI or Ethernet are not described in the following tables because the System BIOS automatically configures (PnP, Plug and Play) each PCI device to avoid address conflicts.

Many device drivers show the actual address locations after installation and loading.

Standard Register Set

The standard register set is the same as the standard PC/AT systems. The table below provides an overview of the address ranges occupied by these registers.

Table 19: Standard register set

I/O Address Range (Hex) Function

0000 - 000F

0020 - 0021

0040 - 0043

0060

0061

0064

0070 - 0071

0080 - 008F

00A0 - 00A1

00B2 - 00B3

00C0 - 00DE

00F0 - 00F1

0160 - 016F

DMA Controller 1

Interrupt Controller 1

Counter / Timer

Keyboard Controller

NMI Status and Control

Keyboard Controller

RTC, NMI Mask

DMA Page register

Interrupt Controller 2

Power Management

DMA Controller 2

Coprocessor

Reserved b

0170 - 0177

01F0 - 01F7

0278 - 027F

02E8 - 02EF

02F8 - 02FF

0378 - 037F

03BC - 03BF

03E8 - 03EF

Secondary EIDE

Primary EIDE

LPT a

COM port a

COM port a

LPT a

LPT a

COM port a

03F2 - 03F7 Floppy

03F8 - 03FF COM1 port a a. Via setup three address ranges can be defined for the parallel interfaces and four address ranges for the serial interfaces.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 62

Interrupts

b. Used for onboard programmable options. They are not intended to be used from normal users. For more explanation please check the ‘Board

Specific Hardware Programmer’s Manual’

Plug and Play Devices

See ‘Board Specific Hardware Programmer’s Manual’

The interrupt routing for standard components such as COM1/2 or LPT1 is in compliance with standard PC/AT systems. Unused interrupts can be used for add-on cards or other board specific PCI devices such as SCSI and Ethernet.

Table 20: Interrupt assignments

Hardware IRQ IRQ Source

IRQ06

IRQ07

INTC2

IRQ08

IRQ09

IRQ10

IRQ11

IRQ12

IRQ13

IRQ14

IRQ15

INTC1

IRQ00

IRQ01

IRQ02

IRQ03

IRQ04

IRQ05

System Timer

Keyboard

Cascade from INTC2

COM2 / COM1 a

COM1 / COM2 a

LPT1 a

/ PnP/PCI b

Floppy Disk Controller

LPT1 a

/ PnP/PCI b

Real Time Clock

Power Management Contr./PCI b

PnP/PCI b

PnP/PCI b

PS/2 Mouse c

Numeric Coprocessor

Rear EIDE d

Onboard EIDE e

ECC Error,

System Error a b

. This interrupt is available when no Interrupt Service Routine is installed.

. Interrupts are available for Plug and Play PCI devices c

. This interrupt is available when PS/2 mouse is not connected. d

. This interrupt is available when the primary EIDE is disabled in SETUP.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 63

APIC Controller

e

. This interrupt is available when the secondary EIDE is disabled in SETUP.

The Cx9 supports also the Interrupt handlings with APIC (Advanced Interrupt

Controller). This handling of the APIC interrupt services must be supported by the operating system. The I/O APIC handles interrupts very differently than the 8259. Briefly, these differences are:

Method of Interrupt Transmission. The I/O APIC transmits interrupts through a three wire bus, and interrupts are handled without need for the processor to run an interrupt acknowledge cycle.

Interrupt Priority. The priority of interrupts in the I/O APIC is independent of the interrupt number. For example, interrupt 10 may be given a higher priority than interrupt 3.

More Interrupts. The I/O APIC in the Intel ICH4 supports a total of 24 interrupts.

For a complete operation description please refer to the ‘Intel ICH4 I/O

Controller Hub’ datasheet.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 64

CHAPTER 7 Function Blocks

Chapter Scope

This section gives a brief overview of the software interfaces of onboard devices on the Cx9 CompactPCI Single Board Computer.

Processor

The Intel Pentium M processor family provides high performance with low power and features Enhanced Intel SpeedStep® technology which provides the ability to dynamically adjust the power and performance of the processor based on CPU demand. This results in optimal performance without compromising the power performance of the Cx9.

The processor die is thermally protected by two thermal monitor features.

When reaching a maximum safe operating temperature the Thermal Control

Circuit in the processor activates a throttling feature and reduces the voltage and frequency dynamically. If this feature is active the Cx9 will indicate it with short clicks at the speaker. In case of a catastrophic die overheating

(above 125 °C) the Cx9 switches off the processor core voltage. Recovery from this catastrophic event can be done with a power off-on cycle only.

Memory Controller

The memory controller in the Cx9 supports double data rate synchronous

DRAM (DDR SDRAM) with a data bus width of 64 bits + ECC. One, two or four banks are provided by the Cx9 with a size of either 256 MBytes or

512 MBytes. This results in a minimum memory size of 256 MBytes and a maximum size of 2 GBytes.

DMA Controller

In standard AT compatible PCs, as well as on the Cx9, the two DMA controllers integrated on the board are internally cascaded. Both controllers are compatible with the Intel 8237A. The DMA Controller 1 (DMAC1) is

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 65

Interrupt Controller

Timer

used for byte-wide transfers while the DMAC2 is used for word-wide transfers.

The Interrupt controller on a standard PC consists of two 82C59A devices with eight interrupt request lines each. The two controllers are cascaded so that 14 external and two internal interrupt sources are available. The master interrupt controller provides IRQ [7...1], the slave interrupt controller provides IRQ [15...8]. IRQ2 is used to cascade the two controllers, IRQ0 is used as a system timer interrupt and is tied to interval timer 1, counter 0. The remaining 14 interrupt lines are mapped to various onboard devices. Each

82C59A provides several internal registers. The interrupts at the IRQ input lines are handled by two registers, the interrupt request register IRR and the in-service register ISR. For programming details see the 82C59A data sheet.

The Cx9 supports also the Interrupt handlings with APIC (Advanced Interrupt

Controller). This handling of the APIC interrupt services must be supported by the operating system. The I/O APIC handles interrupts very differently than the 8259.

Standard PCs like the Cx9 are equipped with an 8254 compatible timer. This timer contains three counters. Each counter output provides a key system function. Counter 0 is connected to interrupt controller input IRQ0 and provides a system timer interrupt for time-of-day, floppy disk timeout and other system timing functions. Counter 1 generates a refresh request signal and Counter 2 generates the sound for the speaker.

The following table gives an overview over the 8254 functions.

Table 21: Interval timer functions

Interval Timer Functions

Function Counter 0 (System Timer)

Clock In 1.193 MHz (OSC/12)

Function

Clock In

Counter 1 (Refresh Request)

1.193 MHz (OSC/12)

Function

Gate

Counter 2 (Speaker Tone)

Programmable via Port $061

Clock In 1.193 MHz (OSC/12)

Out Speaker

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 66

The counter/timers are programmed by I/O accesses. A single control word register controls the operation of all three counters. For more information on programming and a detailed register description see the 8254 data sheet.

Real Time Clock

Keyboard and Mouse Controller

The communication between the PC and the keyboard is managed by a device compatible with the Intel 8042 microcontroller. This also provides the PS/2 mouse interface.

EIDE Interface

The RTC is a low-power clock that provides a time-of day clock and a 100year calendar with alarm features and battery backed operation. The time-ofday function includes 14 control registers. Other features include maskable interrupt sources and 242 bytes of general purpose CMOS RAM used by system BIOS. Valid RAM data and time can be maintained after power down through the use of an external battery source. The RTC is software compatible to the Dallas DS1287 and the Motorola MC146818.

The Cx9 offers two independent EIDE/ATAPI interfaces. Both channels are logically connected to the primary PCI bus. Therefore a high data transfer rate is achievable. The signals of the secondary EIDE interface are used for connection of a 2,5'' HDD or flash disk via connector P1800 on board. The signals of the primary EIDE interface are available at the backpanel IO connector only. The Cx9 System BIOS automatically detects a connected

EIDE HDD or flash disk and enters the corresponding drive parameters into the BIOS setup. This feature allows faster and easier handling of varying types of EIDE hard disks. At the primary EIDE interface two hard disks can be connected. In this case one HDD must be configured as the master and the other one as a slave. Read the hard disk manual to find out where these jumpers are located on your drive. The optional 2,5” onboard disk is connected to an onboard EIDE connector (secondary EIDE interface).

Using EIDE and SCSI devices: MS-DOS 6.22 can handle up to seven hard disks. The PC allows the simultaneous use of EIDE and SCSI hard disks.

BIOS setup allows reordering drives to boot from either SCSI or EIDE drives.

Please note:

For correct operation of the EIDE interface, a maximum cable length of 12 inches (30 cm) must not be exceeded. For use with fast transfer rates such as

UDMA 66 and higher a high density 80-pin cable must be used. The use of round wired cables is not recommended.

USB Interface

The Cx9 has five USB 2.0 channels. They are backward compatible to USB

1.0/1.1. The USB host controller supports legacy Keyboard/Mouse usage with

USB–based keyboard and mouse without using additional software drivers.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 67

Serial Interface

Parallel Interface

Floppy Controller

Graphics Controller

The Cx9 serial ports are fully compatible with the NS16450 and NS16550.

This means that each serial interface provides a 16 byte FIFO and therefore offers a higher performance than earlier used standard serial interfaces. The

UARTs have programmable baud rate generators capable of 50 to 115200 baud. There are four address locations defined for serial interfaces on standard PCs. The two serial interfaces are I/O mapped and can occupy four address ranges.

The parallel port is fully compatible with the new IEEE 1284 standard, including level 2 support. The parallel ports consist of an Enhanced Parallel

Port (EPP1.7/1.9) and an Extended Capabilities Port (ECP 16-Byte FIFO +

DMA support). The new modes allow higher transfer rates up to 1 MByte/s.

Via BIOS Setup, the operating modes of the parallel interface can be selected.

The following modes are supported:

Table 22: Parallel interface options

Mode Average transfer rate Average transfer rate

Standard

EPP

Read Write

100 kBytes/s

1 MByte/s

200 kBytes/s

1 MByte/s

ECP 1 MByte/s 1 MByte/s

On a standard PC, three address areas are defined for a parallel interface. The parallel interface is I/O-mapped and can occupy three address ranges. The address range $3BC cannot be used with EPP operation.

The Cx9 floppy controller is fully compatible with the PC8477, containing a superset of the NEC uPD72065B and the N82077AA. The floppy controller uses various I/O addresses in the PC I/O address space.

The Graphic Controller NVIDIA® GeForce™ 4 420 Go used in versions 2.x has the following features:

• Highly integrated Flat Panel and CRT GUI

• Max. pixel clock 350 MHz

• Dual Independent Display for CRT front and CRT/Flat Panel rear

• CRT resolution up to 1600x1200, DVI up to 1024x768

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 68

PMC Interface

IPMI (CT9)

The Graphic Controller ATI Mobility™ Radeon™ used in versions 3.x has the following features:

• Highly integrated Flat Panel and CRT GUI

• Max. pixel clock 400 MHz

• Dual Independent Display for CRT front and CRT/Flat Panel rear

• CRT resolution up to 1600x1200, DVI up to 1024x768

Software Installation

Since the NVIDIA and ATI graphic chips are used on a large number of computers, many operating systems like Windows 2000, Windows XP and

Linux Suse 9.1 already include high resolution drivers. The Technical Product

Information CD-ROM supplied with the Cx9 includes the most commonly used software drivers and utilities.

The PCI Mezzanine Card (PMC) Interface is an additional slot for parallel mounted expander or option cards. Please see chapter ‘PCI Mezzanine Card

(PMC)’ on page 99 of this manual for further details. The Cx9 PMC

Connector interface is described on page 94.

A Baseboard management controller (BMC) is implemented on the CT9, the interfacing between host processor and the system management network. This controller can also work as a Peripheral management controller (PM). The

BMC is mapped into the local CPUs I/O address space, specified in the ‘CR9,

CT9, CP9, VR9, VP9 Board Specific Hardware Programmer’s Manual’. The functionality of the IPMI controller is described in the ‘Intelligent Platform

Management Interface for CT9 User’s Manual’.

For information about the System Management in CompactPCI systems, please refer to the PICMG 2.9 specification 'System Management

Specification'. More information about IPMI can be found on the Intel website.

IPMB

The Intelligent Platform Management Bus (IPMB) is an I2C-based bus that provides a standardized interconnection between different CPCI-boards within a chassis. The standardized connection to the backplane is shown below:

Table 23: IPMB backplane pin assignments

J7001 Name Description

B17

C17

A4

IPMB_SCL

IPMB_SDA

IPMB_PWR

Serial Clock

Serial Data

Power Supply for all IPMI-devices

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 69

Ethernet Interface

Additional devices

Private I

2

C

The Private IPMI I

2

C bus is equivalent to the onboard SMBus (described in

'Additional devices/SMB'). The IPMI-controller works as a second Master on the I

2

C bus to read the SMBus devices.

Software Installation

The Technical Product Information CD-ROM supplied with the CT9 includes the most commonly used software drivers and utilities.

The Ethernet controller 82546GB from Intel used with the Cx9 is a high performance dual Gigabit Ethernet 10/100/1000 Mbit PCI controller. Both channels are available on the Cx9. Front or rear Ethernet can be selected via order.

For registration and identification of a workstation in a LAN, a unique ID number is required. Each network card is assigned a unique ID number, which resides in an Ethernet address ROM on the Cx9. An Ethernet boot option can be enabled in BIOS setup.

Software Installation

The drivers available for the Ethernet controller 82546GB support a large number of operating systems. The table shows operating systems supported by the available software:

Table 24: Supported operating systems

Type System

ODI

NDIS

DOS, VxWorks

DOS, Linux

NDIS Windows NT 4.0, 98, 2000, XP

The Technical Product Information CD-ROM supplied with the Cx9 includes the most commonly used software drivers and utilities.

Hot Swap

The PICMG 2.1 Hot Swap compliant Cx9 allows the orderly insertion and extraction under power, without adversely affecting system operation.

According to the PICMG 2.1 Hot Swap specification, the Cx9 uses its 2.7 k pull-up resistors for biasing purposes during hot insert. During this phase all

CPCI signals are pre-charged to 1.1 V with these 2.7 k resistors.

The Hot Swap process can be described in terms of three processes:

Physical Connection Process - describes the acts of:

• Hot Insertion - by which Cx9 is installed in a live system (as a nonsystem CPU)

• Hot Extraction – which means the Cx9 is removed from a live system (as a non-system CPU)

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 70

• Hardware Connection Process - Power Up/Down of the Cx9 onboard voltages

• Software Connection Process - Connection/disconnection of the software layer(s)

At the end of the Physical Connection Process (the shortest Pin has connection) the Hot Swap controller powers up the onboard voltages in a defined manner.

After the handle switches are closed, the CPCI bridge generates an insertion event, which signals a Hot Swap insertion to the system. The system then scans the CPCI-bus for changes.

Please note

The CPCI backplane must support this function and appropriate software must be installed for Hot Swap to work properly.

SMBus devices

The Cx9 uses a serial 2-wire I2C bus to communicate with several onboard devices:

Table 25: SMBus devices

Device Designators SMBus address a

Clock synthesizer *

User Serial EEprom (24C04)

Optional big User EEprom

SPD EEprom Bank 0 *

SPD EEprom Bank 1 *

Factory EEprom *

U1000

U1980

U1983

U1981

U1981

U1984

1101 001Xb

1010 00XXb

1010 010Xb

1010 100Xb

1010 101Xb

1010 11XXb

Temperature sensor LM83

Temperature sensor LM75-1

Temperature sensor LM75-2

Analog Digital Converter

U1982

U1985

U1986

U1953

0011 001Xb

1001 110Xb

1001 111Xb

1001 000Xb

IPMI Controller

Northbridge E7501

U8000

U1300

0010 XXXXb

0011 000Xb

Southbridge ICH4 (slave) U1600 1000 100Xb

PCI Bridge P64H2 * U6000 1110 011Xb

Devices marked by * are handled by BIOS. It is strongly recommended not to access these devices by user software.

An X at bit 0 represents the R/#W bit.

SMBus external (IPMB)

The Intelligent Platform Management Bus (IPMB) is available on the J7002

CPCI connector for external use. External access via IPMB to the onboard

SMBus devices can only be done via the IPMI controller. For more

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 71

information please see the IPMB description on page 69 within the IPMI

controller section.

Temperature Sensor LM83

A National Semiconductor LM83 temperature sensor is implemented on the

Cx9 board. The sensor is located close to the CPU and shows the dietemperature of the CPU and the local onboard temperature. The sensor has an over-temperature output integrated, which can be used to take actions like reducing the CPU speed. For programming information please see the 'AMI-

BIOS for CR9, CP9, CT9 User’s and Programmer’s Manual'.

More information on the LM83 can be found in the data sheet from National

Semiconductors.

Temperature Sensors LM75

Two LM75 temperature sensors from National Semiconductors are implemented on the Cx9 board. The first sensor shows the average between the air temperature below the heatsink and the PCB temperature in the CPU area. With the second LM75 the air temperature across the CPCI bridge and the Ethernet controller can be read. This reading is also influenced by the

PCB temperature is measured below the heatsink.

Serial EEPROM

For storage of user data a serial EEPROM is implemented on the Cx9 board..

The user EEPROM is a 24C512 type with 64 kByte. More information about writing and reading the contents can be found in the data sheets from the manufacturer (e.g. Microchip Technology, SGS Thomson, Atmel, Catalyst and many others).

Power Management Event

A Power Management Event can be initiated on Cx9 by one of the following events.

Table 26: Power management events

Event Description

ENUM

REMOVE

Wake Cx9 a

if a non-system board is removed or inserted

Wake Cx9 if user wants to remove this Cx9

Wake on LAN Wake Cx9 by Ethernet event

Wake on IO a

. Cx9 in System slot

Wake Cx9 by IO-device i.e. Modem, KB, MS, etc.

INTP, INTS

The INTP and INTS signals (PICMG2.0) are available on the J7001_D4/E4.

For Cx9 in System Slot, the high active INTP is used as a steerable interrupt which is routed to any legacy ISA interrupt. In Peripheral Slot, INTP can be

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 72

generated to trigger an interrupt in the system board. The corresponding interrupt for INTP is selectable via BIOS Setup.

Please note:

Only one peripheral board is allowed to use INTP.

For Cx9 in System Slot, the INTS signal can be used as serialized interrupt, in compliance with the ‘Serialized IRQ Support for PCI Systems’ specification,

Rev. 6.0. INTS is synchronous to the PCI clock and has the requirement of meeting the PCI specification.

ENUM#

ENUM (PICMG 2.0, open-collector) is available on J7001_C25. This signal is be driven by Hot Swap compatible boards after insertion and prior to removal.

For Cx9 in System Slot, the input ENUM is able to generate an interrupt to force the software to interrogate all boards within the system for resource allocation regarding I/O, memory and interrupt usage.

If the Cx9 works in a peripheral slot, the non-transparent bridge generate the output ENUM conform to the specification of a Hot Swap compliant board.

For programming information about this PnP device, please see the 'AMI-

BIOS for CR9, CP9, CT9 User’s and Programmer’s Manual'.

Geographic Addressing

If the backplane supports geographic Addressing, the Cx9 can detect the unique Address in a CPCI-System with the GA [4...0] pins (PICMG 2.0) on

J7002.

For programming information please see the 'AMI-BIOS for CR9, CP9, CT9

User’s and Programmer’s Manual'. For more information about geographic addressing in appliance to system management, see PICMG 2.9.

GPIO (0...7)

Eight GPIO pins are available on J7004. These pins can be used for I/O functions with output 3.3 V signals as well as 5 V tolerant inputs.

For more information please see the ‘Board Specific Hardware Programmer’s

Manual’.

Watchdog

For security of application software, the Cx9 offers a software controlled hardware two stage watchdog with independent count values for each stage.

First stage generates an INT or SMI. The second stage issuing a reset signal if its time-out interval expires. The configurable granularity reaches from 1µs to

10min.

For more information please see the Intel ICH4 I/O Controller Hub datasheet and the ‘Board Specific Hardware Programmer’s Manual’.

Programmable Timer

An additional programmable Timer is implemented on the Cx9. The timer can generate an Interrupt.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 73

For more information please see the ‘Board Specific Hardware Programmer’s

Manual’.

LEDs

Two LED’s are available at the front panel green/red and blue.

The Status LED is a green/red bi-color for BIOS power-up status indication, after boot loading the user software is free to use this LED for it’s own purpose.

Table 27: BIOS power-up status

Power-up, still Reset state

BIOS early init

BIOS start POST

BBIOS POSTA init

Red on (also the blue LED is on)

Blink red 1Hz

Blink amber 1Hz

Blink green 1Hz up to 4Hz

OS boot Green on

System halted or reset Red on

The blue LED is the Hot Swap LED and is working according the Hot Swap specification.

Reset Button

There is a Reset Button onboard. An external Reset button may be connected between the appropriate IO connector at the back side and GND. The PRST# on J7002_C42 (PICMG2.0) is used as Reset input only for the system board and is in this case, compatible to the onboard button.

• If the Cx9 works as a System board:

The push button will issue a hard power-on reset. The reset signal is active for all subsystems of the Cx9.

• If the Cx9 works as a Peripheral board:

1) The push button will issue a hard power on reset. The reset signal is active for the Cx9 including PMC modules, but will not reset other peripherals or the System board.

2) The Cx9 will signal a Hot Swap Insertion event when reset.

Speaker

An internal speaker is implemented on the Cx9 except on a CR9 N-Style (or

8-style). An external standard PC compatible speaker may be connected between the appropriate IO connector at the backside and +5 V.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 74

CHAPTER 8 Specifications

PCB

FR4 Multilayer

Size

Total board size: 6U, 4 HP (CR9 and CT9)

Total size with optional extension board 8HP (CP9)

Dimensions

PCB: 233.35 mm x 178 mm x 20 mm (CR9 and CT9 single slot)

PCB: 233.35 mm x 178 mm x 40 mm (CP9 dual slot)

Mechanical Incompatibility

There is an incompatibility in terms of component height on the Cx9 boards close to the P3 connector (CompactPCI). The Ethernet transformer is slightly higher than the height envelope of the respective specification

allows. This is to be checked when planning to insert a PMC mezzanine module in the center of a 6U board (PMC1). If no PMC is inserted into this mezzanine slot then there is no mechanical height violation.

Weight

Approx. 650 g (with front panel, HDD and heat sink),

Depending on model and style

RoHS compliance

Version 2 of Cx9 is only available in Non-RoHS

Version 3 of Cx9 is available in Non-RoHS and RoHS

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 75

Power Consumption

The following table is intended to help you calculate the power consumption of a Cx9 system. For measurement, the Cx9 board is mounted on a CPCI backplane. During measurement, the power consumption of the backplane, keyboard and the hard disk drive are withdrawn from the results. The values are typical measured. The current drawn from +5 V supply the CPU and all external devices. The 3.3 V supply all other components on the Cx9.

Table 28: Power consumption CPU dependent without Power management,

CPU die around +50

°C* running full cache access,

CPU die around +50

°C*

Windows XP,

CPU running a maximum power consumption instruction mix at

+100 °C die temperature

+5 V +5 V

0.9 A 0.9 A Pentium M 600

MHz 130 nm

+5 V

0.7 A

Celeron M 1.0 GHz

90 nm **

Pentium M 1.1 GHz

130 nm

Pentium M 1.4 GHz

90 nm **

Pentium M 1.6 GHz

130 nm

Pentium M 1.8 GHz

90 nm

0.7 A

1.2 A

1.2 A

2.7 A

2.5 A

0.9 A

1.6 A

1.6 A

3.5 A

3.0 A

Celeron M 1.3 GHz

130 nm

2.2 A 2.6 A

* for every 25 °C more please add around 10 %

** estimated values

0.9 A

2.3 A

2.3 A

5.4 A

4.5 A

4.6 A

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 76

Table 29: Power consumption DRAM dependent

256 MB (1 bank, 9 devices)

512 MB (2 banks, 18 devices)

CPU running or Windows XP, 3D during graphics active, full cache access, mid range temperature memory initialization both Gigabit

Ethernet channels linked

+3.3 V

4.9 A*

+3.3 V

5.8 A*

+3.3 V

6.2 A

5.2 A* 6.2 A* 6.7 A

1 GB (4 banks, 36 devices)

5.9 A* 7.1 A* 7.5 A

2 GB (4 banks, 36 devices)

5.9 A* 7.1 A* 7.5 A

* for every Ethernet channel linked to gigabit please add 0.55A

The exact values may vary with different dram vendors by +/- 20 %

• When using onboard PMC modules don’t forget to add their power consumption

• With an onboard hard disk drive please add following values to the +5 V current:

• During power up 0.9 A max.

• In an idle condition 0.13 A typical.

• During read/write access 0.42 A typical

Values are taken from the Fujitsu MHT 2060 AT datasheet

• With an onboard compact flash drive please add 0.1 A to the +5 V current

• For keyboard, mouse, etc. please add 0.1 A (typical) to the +5 V current

• Connectors P1680, P2001, and P4200 provide fused VCC voltage (+5

V). The total current drawn from this source may not exceed 1.0 A

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 77

Onboard Lithium Battery

BR1225, estimated life time depending on temperature and power status:

Table 30: Lithium battery parameters

External Battery Input

Temperature Cx9 powered Cx9 power off

<=35 °C

+50 °C

120 month

100 month

24 month

12 month

+70 °C 80 month 6 month

+85 °C 60 month 3.5 month

With the values from the table above, it should be possible to calculate the battery lifetime based on the used power on/off ratio.

The battery has a user accessible holder on the Cx9.

If exchanged by customer, please use same type for replacement and

ensure correct polarization.

For operating without battery please check the following description of

the external battery input.

VBATIN input ranges 2.4 to 3.3 V, max. Current (@ 3.0 V; 35 °C) 5 µA

Without an onboard battery it is recommended to use an external supply connected to this input. This voltage supplies the real time clock and the

CMOS RAM for storing the BIOS Setup settings.

Without battery and without this supply voltage, the real time clock oscillator has to be started at each power up. This time gets longer when operating at lower temperatures and can be up to around 30 seconds (at -40 °C). At normal ambient temperatures this delay is below one second.

The red status LED goes off after the reset sequence and starts its normal blinking within the BIOS POST after the RTC oscillator is up.

When ordering a battery-less CR9, the setup information is stored automatically within an onboard EEPROM and is updated via standard BIOS

Setup function. No external software is needed to create a user defined setup like in earlier products from SBS Technologies. It is still recommended to use an external supply voltage to this battery input to avoid the power on oscillator start time and to keep the date and time information.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 78

Environment Conditions

Ambient temperatures and humidity values for the Cx9:

Table 31: Environment conditions

High Temperature

- Storage (see note below)

- Operating (see diagram below)

Low Temperature

- Storage (see note below)

- Operating

Temperature Shock

- Storage

- Operating

+85 °C

-40 °C

0 °C

+/-10 °C/min

+/-5 °C/min

+85 °C

-40 °C

-40 °C

+/-20 °C/min

+/-10 °C/min

Relative Humidity

- Storage, Operating Up to 95 %, non-condensing

CT9 and CP9 only support C-, 1- and I-, 3-style

Storage temperature on R-, N- or 6-, 8-style is between -55 °C (low) and

+105 °C (high).

Shock and vibration values for the Cx9:

Table 32: Shock & vibration parameters

C-, D-, 1-, 2-

Style

I-, H-, R-, N-, 3-,

4-, 6-, 8-Style

C-, D-, I-, H-, 1-, 2-,

3-, 4-Style

R-, 6-Style N-, 8-Style

Vibration

- Spectrum

- Acceleration

5 to 100 Hz

2 g rms

5 to 2000 Hz

2 g rms

Shock

- Amplitude

- Duration

CT9 and CP9 only support C-,1- and I-, 3-style

Maximum height usage

12 g

6 ms

20 g

6 ms

5 to 2000 Hz

14 g rms

40 g / 100 g

11 ms / 6 ms

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 79

90,0

80,0

70,0

60,0

50,0

40,0

30,0

0,5 1

Table 33: Maximum height usage

C-, D-, I-, H-, R-,

1-, 2-, 3-, 4-, 6-Style

N-, 8-Style

Maximum height

- Operating

- Storage

4.5 km

12 km

Vacuum

Vacuum

Only the N-, 8-style board is capable to be used in a vacuum environment. All other styles contain either batteries and do not have the possibility to be cooled without airflow.

For highest operating temperatures (C-, D-, I-, H-, R-, 1-, 2-. 3-. 4-, 6-Style) please refer to the following diagram:

CR9/CT9/CP9 no PMC, no HDD, next slot occupied, worst thermal contact running full cache access

1.0 GHz Celeron M '373' 90nm

600 MHz Pentium M 130nm

1.4 GHz LV-Pentium M 90nm

1.1 GHz Pentium M 130nm

1.8 GHz Pentium M 90nm

1,5

1.3 GHz Celeron M 130nm

1.6 GHz Pentium M 130nm

VGA Limit 3D and/or TMDS for 600MHz, 1.1GHz, 1.4GHz

VGA Limit 2D, no TMDS or

Ethernet Limit 2xGigabit for 600MHz, 1.1GHz, 1.4GHz

2 2,5 3 3,5 4 Airspeed m/s

Figure 19: Temperature vs. airspeed

• 0.5 m/s airflow means convection cooled only with free airflow. This is the minimum required airflow for the Cx9.

• The core temperature of the CPU can be read out via the onboard temperature sensor. The value must be kept below 100 °C for all operating conditions. This value is already included in the airspeed diagram above. If this temperature limit is violated, the Pentium CPUs will start to reduce its internal frequency temporarily. This can be heard by a short click of the speaker which occurs every 0.8 seconds. The

Celeron processor will not automatically switch down to lower frequencies but will stop its internal clock in preprogrammed intervals.

• In the diagram above you can find two temperature limits. One shows the maximum operating temperature when using graphics with 3D

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 80

applications or the TMDS interface. The other shows the limit with the graphics option mounted or when using the Ethernet interface with both channel in Gigabit mode. For Fast Ethernet (100 Mbit). This limit needs not to be taken into consideration. Both limits are valid with the low power CPUs running at 600 MHz or 1100 MHz. For higher CPU frequencies, the maximum operating temperature is limited by the CPU already.

• When using an onboard hard disk drive (not with flash disk) the operating temperature is limited to 50 °C

• When using one or two PMC modules, please consider their power consumption and thermal limits in calculating the max. operating temperature

For more information on the N-, 8-style version, please check the thermal report document of the CR9.

Electrical Characteristics

The supply voltages are +5 V, 3.3 V, +12 V. The -12 V are required only if needed on the PMC slot. All Output voltages of the Cx9 boards have an over current protection. The maximum current for each voltage is shown below:

Table 34: Power supply parameters

Name U Imax Description Fuse

+12VIN 12 V 0.5 A Supply for Hot Swap controller and PMC-Module

U7700

-12VIN

USB_VCC

-12 V 0.1 A Supply for PMC-Module

5 V 2 A

U7700 a

Supply for front panel USB F1681 b a

F1680 b

USBR_VCC 5 V 2 A Supply for rear USB via transition module

FUSE_VCC 5 V 2 A Supply for front panel I/Os:

KB/MS, CRT-DCD a

. LTC1643L-1CGN (Linear Technologies) b

. TPS2034D (Texas Instruments)

Supply voltage range

F9001 b

The following ranges are defined by the CPCI specification PICMG 2.0 Rev

3.0. The voltages have to be measured at the Cx9 board (for example at the

CPCI connector pins at the solder side):

Table 35: Supply voltage range

Supply Voltage and tolerance

+5 V

+3.3 V

+12 V

5.0 V +5 % / -3 %

3.3 V +5 % / -3 %

12.0 V +/- 5 %

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 81

GPIO 0...7

This general purpose I/O pins can be used as inputs, with following signal levels:

Table 36: GPIO input voltages low -0.5 V ... +0.8 V high +2.0 V ... +5.5 V

When used as outputs, the following signal levels are supplied:

Table 37: GPIO output voltages

Signal level at current low -0.4 V at 6 mA sinking high +2.4 V at 3 mA sourcing

Electrical clearance

Starting with board version x.y certain rules on spacing between conductors on individual layers of the printed circuit board (PCB) apply. The boards starting with version V3.x are designed to meet the parameters as listed below.

Voltage between conductors (DC or AC peaks) of 51 V – 100 V require a spacing of

- 0.6 mm for type B2 conditions external conductors, uncoated, sea level to 3050 m.

These rules are in accordance with IPC-2221 requirements.

Isolation

The Isolation of the Ethernet outputs whether front or rear is limited to 500 V peak against GND and any other supply voltage.

By itself the onboard digital ground GND and the front panel/chassis frame ground FGND are isolated on the Cx9 with a layout distance of more than 0.3 mm in all PCB layers. However, most standard devices (keyboard, mouse, and monitor) except Ethernet will connect FGND and GND directly in the device. Also standard racks (our starter cage too) connect both grounds at the power supply for safety reasons.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 82

Placement Plan Component Side Cx9 V2

Figure 20: Cx9 V2 component side placement plan

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 83

Placement Plan Solder Side Cx9 V2

Figure 21: Cx9 V2 solder side placement plan

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 84

Appendix A Transition Module CTM12

The CTM12 transition module is used for easy connection of I/O signals to standard connectors.

Please note:

Additional +5 V/+12 V Power must be provided to the CTM12 via P7700 to supply an external EIDE or a 1” high floppy disk drive via the power output

P7701. This must be done when the Cx9 is intended to be used as a Hot Swap board for ramping up the external drives after the Cx9 is inserted in the backplane. Without the need for Hot Swap, the external drives may be connected direct to the power supply and P7700 and P7701 need not to be connected except the +12 V from P7700 for the PIM connectors P7100/P7200 are needed.

Please note:

You either can use a DVI display on P4100 or a standard VGA

Monitor/Display connected to P4001 or a standard VGA Monitor/Display via a DVI-to-VGA adaptor connected to P4100. You never can use two display devices connected to the transition module. If you want to have two display outputs, you will have to connect one to the front of the Cx9 and one to the rear/transition module.

Please refer to the drawing for the location of available interfaces:

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 85

Figure 22: CTM12 component locations

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 86

CTM12 Interfaces

This chapter describes all connector pinouts on the CTM12 transition module.

EIDE Connector P1800

The IDE interface is designed as a 40-pin 2.54 mm pitch male connector to connect directly to one or two external EIDE hard drives. The cable length must not exceed 30 cm. It is recommended to use an 80-pin high density cable for UDMA 3 and higher transfer.

Table 38: CTM 12 EIDE connector

Name

GND

HD_D8

HD_D9

HD_D10

HD_D11

HD_D12

HD_D13

HD_D14

HD_D15

P1800

2 1

4 3

6 5

8 7

10 9

12 11

14 13

16 15

18 17

Name

\RST_DRV

HD_D7

HD_D6

HD_D5

HD_D4

HD_D3

HD_D2

HD_D1

HD_D0

GND

GND

GND

22 21

24 23

26 25

HD_DRQ0

\HD_IOW

\HD_IOR

GND 30 29 HD_DAK0

NC 32 HD_IRQ

HD_A2 36 35 HD_A0

\HD_CS3 38 37 \HD_CS1

GND 40 39

Ethernet Interface 10/100/1000BaseT P5000 and P5500

NC

The Ethernet interfaces for Rear-IO requires usage of CAT 5 cable for proper operation with 100/1000BaseT.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 87

LED 1 LED 2

Figure 23: CTM12 Ethernet connector layout

Table 39: CTM12 Ethernet connector pin assignments

Name 10/100base Name 1000base Ethernet1, 2

TxD+ LP_DA+

TxD- LP_DA-

1

2

RxD+ LP_DB+

NC

3

LP_DC+ 4

NC

LP_DC- 5

RxD- LP_DB-

NC

6

LP_DD+ 7

NC

LP_DD- 8

Two LED’s (LED1 and LED2) are integrated in each of the RJ45 connector.

These LED’s indicates the link status of the interface.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 88

LED1 green

Table 40: CTM12 Ethernet connector LED

Function green blink green/orange

LED2 yellow

General link

General link with Rx/Tx activity

Function green

Orange

Parallel Interface LPT1 P2002

Link 100 Mbit

Link 1000 Mbit

Table 41: Parallel connector pin assignments

Name P2002

\Strobe

D0

D1

D2

D3

D4

D5

D6

D7

\ACK

BUSY

PE

SLCT

\AUTOFEED

\ERROR

1

3

5

7

9

11

13

15

17

19

21

23

25

2

4

\INIT

\SLCTIN

6

8

GND 10,12,14,16,18,20,22,24

FUSE_VCC

a

26 a

+5 V supplied by the Cx9 and fused with max 2 A at CTM12 for normal operation don’t exceed 100 mA at this pin.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 89

Serial Interfaces COM1 P2200 and COM2 P2201/P2203

The Cx9 offers two RS232 serial ports. All COM ports are accessible via the

Transition module at 10-pin headers and are software selectable for RS-232 or RS-422/485 operation. The RS485 output drivers can be enabled or disabled with the DTR signal. An active DTR means the drivers to be enabled. When using the RS422 setting the output drivers are always enabled and the DTR signal is not used. COM2 is also available at the rear panel with a 9-pin D-sub connector.

Table 42: COM1/COM2 connector pin assignments

Name RS232 Name RS422/485 COM2 P2203 P2200,2201

DCD TXD-

DSR TXD+

RXD RTS-

RTS RTS+

TXD CTS+

CTS CTS-

1

6

2

1

2

3

7 4

3 5

8 6

DTR RXD+

RI RXD-

4 7

9 8

GND GND 5 9

FUSE_VCC a

- 10 a

+5 V supplied by the Cx9 and fused with max 2 A at CTM12 for normal operation don’t exceed 100 mA at this pin.

VGA Interface P4001

The VGA monitor signals are available on P4100 a 10-pin male header. They are parallel connected with the DVI-I connector P4100. You either can use a

DVI display on P4100 or a standard VGA Monitor/Display connected to

P4001 or a standard VGA Monitor/Display via a DVI-to-VGA adaptor connected to P4100. You never can use two display devices connected to the transition module. If you want to have two display outputs, you will have to connect one to the front of the Cx9 and one to the rear/transition module.

Table 43: VGA connector pin assignments

Name P4001

RED 2

GREEN 4

BLUE 6

HSYNC 8

VSYNC 10

GND 1, 3, 5, 7, 9

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 90

DVI-I connector P4100

The CTM12 provides a DVI-I connector to connect DVI capable monitors.

Both digital and analog video signals are provided. For the digital signals the

Transition Minimized Differential Signaling (TMDS) is used. The maximum resolution with a Cx9 is limited to 1024x768.

Figure 24: DVI connector layout

Table 44: DVI connector digital pin assignments

1 TX2- (TMDS Data2–) 13 NC

(TMDS 14

a

3 GND

4 NC

5 NC

6 DDC Clock

17

18

TX0- (TMDS Data0–)

TX0+ (TMDS Data0+)

8 VSYNC

9 TX1- (TMDS Data1–) 21

NC

(TMDS 22 GND

11 GND

12 NC

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 91

Table 45: DVI connector analog pin assignments

C1

C2

C3

RED Analog Red Video

GREEN Analog Green Video

BLUE Analog Blue Video

C4 HSYNC Analog Horizontal Sync

C5 GND a

+5 V supplied by the Cx9 and fused with max 2 A at CTM12 for normal operation don’t exceed 100 mA at this pin.

USB connector P2005

Four channels are available on a 10-pin male header. USBVCC is supplied and controlled by the Cx9 board. It is fused with 2 A, but for normal operation don’t exceed 1 A at this pin.

Table 46: USB connector (10-pin header) pin assignments

Name P2005

USB0- 1

USB0+ 29

USB1- 3

USB1+ 4

USB2- 5

USB2+ 6

USB3- 7

USB3+ 8

GND 9

USBVCC 10

Floppy connector P2003/2004

The CTM12 provides a connector for direct adaptation of a floppy drive via a standard 2.54 mm 34-pin connector. For connection to the floppy drive please use a non twisted 34-pin flat cable connected to P2004. Alternatively, you can use a 26-pin foil cable connector (P2003).

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 92

Table 47: Floppy connector pin assignments

P2003 P2004 Name

\INDEX

\DRVSEL

\DSKCHG

\MOTOR

\DIR

\STEP

2

4

6

10

12

14

8

12

34

16

18

20

\WRDATA

\WGATE

\TRACK0

\WRPROT

16

18

20

22

22

24

26

28

\RDDATA

\HDSEL

24

26

30

32

GND 15, 17, 19, 21, 23, 25 1, 3, 5, 7, 9, 11, 13, 15,

17,19, 21, 23, 25, 27, 29,

31, 33

FUSE_VCC a

1, 3, 5 -

NC 7, 8, 9, 11, 13 2, 4, 6, 10, 14 a

+5 V supplied by the Cx9 and fused with max 2 A at CTM12 for normal operation don’t exceed 100 mA at this pin.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 93

Miscellaneous connector

P2000 contains miscellaneous signals:

Table 48: Miscellaneous connector pin assignments

P2000 Name

NC

NC

GND

FUSE_VCC a

FUSE_VCC a

FUSE_VCC a

FUSE_VCC a

GND

FUSE_VCC a

GND

FUSE_VCC a

USB1+

USB2+

GPIO1

1 2

3 4

5 6

7 8

9 10

11 12

13 14

15 16

17 18

19 20

21 22

23 24

25 26

27 28

Name

NC

NC

\RST_BUT

\SPEAKER

\WDG_REL

\LED

MOUSE_CLK

MOUSE_DAT

KBD_CLK

KBD_DATA

USB1-

USB2-

GND

VBATIN b a

+5 V supplied by the Cx9 and fused with max 2 A at CTM12 for normal operation don’t exceed 100 mA at this pin.

b

VBATIN is used to connect an external battery to Cx9. For description please check the section External c

Battery Input.

VIO is the I/O voltage of the PMC slot and is connected to +5 V on the CT

PMC I/O connectors

The PMC I/O signals of both PMC slots are either available at 64-pin male headers (P7101/P7201) or via VITA36 compliant PIM (PMC I/O Module) connectors (P7100/P7104 and P7200/P7204). The availability of a PIM interface or 64-pin header is mutually exclusive.

The following table lists the pin assignments of the onboard PIM connectors.

The I/O signals from PMC 1 (PMC1IO_xx) are connected to P7104 and the

I/O signals from PMC 2 (PMC2IO_xx) are connected to P7204.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 94

Table 49: PMC I/O onboard PIM connector pin assignments

P7100/P7200 P7104/P7204 Pin Pin P7100/P7200 P7104/P7204

PMCxIO_03

+5 V

a

PMCxIO_05 05 06 PMCxIO_06

PMCxIO_08

a

PMCxIO_10

GND PMCxIO_13 14 PMCxIO_14

PMCxIO_17

PMCxIO_19 19 20

+5 V

a

PMCxIO_21 21 22

PMCxIO_20

PMCxIO_22

PMCxIO_24

a

PMCxIO_26

GND PMCxIO_29 30 PMCxIO_30

PMCxIO_35

+5 V

a

PMCxIO_37 37 38 PMCxIO_38

PMCxIO_40

a

PMCxIO_42

GND PMCxIO_45 46 PMCxIO_46

PMCxIO_51

+5 V

a

PMCxIO_53 53 54 PMCxIO_54

PMCxIO_56

a

PMCxIO_58

PMCxIO_59

-12 V

a

PMCxIO_61 61 62 PMCxIO_62 a

+5 V, +3.3 V, –12 V nonfused supplied via Cx9, max 1 A for +5 V and

+3.3 V, and 100 mA for –12 V b

+12 V supplied via the CMT12 external power connector P7700, max current

500 mA

The following table lists the pin assignments of the PMC I/O signals of the 64pin header.

The I/O signals from PMC 1 (PMC1IO_xx) are connected to P7101 and the

I/O signals from PMC 2 (PMC2IO_xx) are connected to P7201.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 95

Table 50: PMC I/O 64-pin header connector pin assignments

P7101/P7201 Pin P7101/P7201

PMCxIO_01 1 2 PMCxIO_02

PMCxIO_03 3 4 PMCxIO_04

PMCxIO_05 5 6 PMCxIO_06

PMCxIO_07 7 8 PMCxIO_08

PMCxIO_11 11 12 PMCxIO_12

PMCxIO_13 13 14 PMCxIO_14

PMCxIO_15 15 16 PMCxIO_16

PMCxIO_17 17 18 PMCxIO_18

PMCxIO_19 19 20 PMCxIO_20

PMCxIO_21 21 22 PMCxIO_22

PMCxIO_23 23 24 PMCxIO_24

PMCxIO_25 25 26 PMCxIO_26

PMCxIO_27 27 28 PMCxIO_28

PMCxIO_29 29 30 PMCxIO_30

PMCxIO_31 31 32 PMCxIO_32

PMCxIO_33 33 34 PMCxIO_34

PMCxIO_35 35 36 PMCxIO_36

PMCxIO_37 37 38 PMCxIO_38

PMCxIO_39 39 40 PMCxIO_40

PMCxIO_41 41 42 PMCxIO_42

PMCxIO_43 43 44 PMCxIO_44

PMCxIO_45 45 46 PMCxIO_46

PMCxIO_47 47 48 PMCxIO_48

PMCxIO_49 49 50 PMCxIO_50

PMCxIO_51 51 52 PMCxIO_52

PMCxIO_53 53 54 PMCxIO_54

PMCxIO_55 55 56 PMCxIO_56

PMCxIO_57 57 58 PMCxIO_58

PMCxIO_59 59 60 PMCxIO_60

PMCxIO_61 61 62 PMCxIO_62

PMCxIO_63 63 64 PMCxIO_64

Power connector P1801

This optional 3-pin connector provides +5 V to supply external logic or devices as 2.5” hard drives etc.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 96

Table 51: Power connector pin assignments

Name P1801

GND 1

FUSE_VCC

a

2

GND 3 a

+5 V supply via Cx9 and fused with max 2 A at CTM12. Don’t exceed 1 A at this connector for normal operation.

Power IN/OUT connectors P7700, P7701

In case of Hot Swap (insertion or extraction phase) of the Cx9 the CTM12 provides the possibility of switch-off the power to external storage devices. The voltage +5 V and +12 V between power-in P7700 and power-out P7701 controls a Hot Swap controller via MOSFETs. The Hot Swap controller cut the voltage when the signal VCCOFF# is low. VCCOFF is controlled by the Hot

Swap at the Cx9. In case of over-current the controller switches off the voltages, too.

Table 52: Power IN/OUT connector pin assignments

Name Power In P7700 Power Out P7701

+12 V 1 4

GND 2 3

GND 3 2

+5 V

Over-current threshold:

+5 V 6 A

+12 V 3 A

4 1

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 97

Placement Plan

Figure 25: Placement Plan CTM12

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 98

Appendix B PCI Mezzanine Card (PMC)

Electrical characteristics

The PCI Mezzanine Card (PMC) Interface is an additional slot for parallel mounted add on cards. The interface is compliant to the IEEE 1386.1 specification and is based on the electrical and logical layer of the PCI specification. Check for possible height incompatibility in ‘Features’ and

‘Specifications’ sections of this manual. PMC Slot1 is 66/100/133 MHz PCI-

X capable. PMC Slot 2 is 33 MHz/32 bit only. The user definable I/O pins are connected to the rear IO connector on the Cx9, as defined in the PICMG 2.3 specification.

• A 5 V key is mounted on PMC2, for 5 V compatible PMC-Cards.

• A 3 V key is mounted on PMC1, for 3 V compatible PMC-Cards.

Table 53: Electrical characteristics

Parameter Comment Value

I3.3V

I5V

Max. current on 3.3 V Pins

Max. current on 5 V Pins

I+12V

I-12V a

V(I/O) b

Max. current on +12 V Pin

Max. current on -12 V Pin

Voltage for PCI IO

P Max. power consumption total a) -12 V must be connected to the backplane b) The appropriate key has to be mounted c) Total power dissipation on 3.3 V and 5 V rail is 7.5 W

2.1 A c

1.2 A c

0.1 A

0.1 A

3.3 V or 5 V

7.5 W

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 99

To mount a PMC board to the Cx9, follow these steps:

1. Remove Cx9 from system housing

2. Remove the front panel cover of the PC slot

3. Take PMC from inside through front panel and push connectors together.

4. Verify correct installation of EMC gasket

5. Fix PMC on host boards with the four screws supplied with the PMC card. The screws must be locked with Loctite 243 when using the Cx9 in a mechanical rough environment.

Figure 26: Mount PMC board to Cx9

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 100

Appendix C

Chapter Scope

Support, Service

And Warranty Information

Geographical Regions:

Technical Support

The following sections describes SBS Technologies’ product support program. It states our product warranty terms and provides details about what action to take if you experience a problem with the product.

World-wide headquarter of SBS Technologies, Inc. is at

SBS Technologies Inc.

7401 Snaproll St., NE

Albuquerque, NM 87109

U.S.A.

SBS Technologies, Inc. uses two regional headquarters for the purpose of support, service, RMA returns and other functions.

Regional areas:

WW world-wide

EU

US

Europe, Russia, Near East, India, Africa

Americas & Pacific Rim (Japan, Korea, China,

Philippines, AUS, NZ)

If you should have a problem with a SBS product: Free technical support is available by phone, fax or email. Telephone support is available during the hours indicated at main locations or at the regional center where the product was bought..

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 101

Support on the Web

Warranty

Repairs

EU US

Monday through Thursday

8:00 – 17:00 (CET)

Friday

8:00 – 16:00 (CET)

Phone +49-821-5034-170

Fax +49-821-5034-119

E-Mail [email protected]

Monday through Friday

8:30 AM – 5:30 PM (Eastern Time)

Phone +1-505-875-0600

Fax +1-505-875-0400

E-Mail [email protected]

For support and information, visit our website at http://www.sbs.com

Information for components, corresponding driver software, etc. can also be found at the following locations: www.amd.com

www.ami.com

Fedora

Linear Technology

Novell www.fedora.redhat.com

www.ibm.com

www.intel.com

www.linear-tech.com

www.microsoft.com

www.freescale.com

www.novell.com

NVIDIA www.nvidia.com

PCI Industrial Computer Manufacturing Group www.picmg.org

PLX Technology www.plxtech.com

www.qnx.com

Red Hat www.redhat.com

Smybios Logic

VITA

Wind River Systems www.lsilogic.com

www.vita.com

www.windriver.com

SBS Technologies’ products come with a ‘return-to-factory’ warranty which covers defects in materials and workmanship for a period of two years in the case of board-level products and one year in the case of system-level

products from the date of product shipment to the customer (original purchaser), provided the product is unmodified and has been subject to normal and proper use.

For details refer to the ‘Terms and Conditions’ of your purchase contract.

Warranty Repairs

Any product returned and found to be under warranty will be repaired or replaced at the discretion of SBS. The return shipping freight is paid by SBS.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 102

Non-Warranty Repairs

If a product is found not to be under warranty, SBS will:

• Repair the product without notice of the customer when the cost is below

Euro/US$250.

• Notify the customer of the non-warranty situation and provide a cost estimate to the customer, if the cost of the repair is equal to or greater than Euro/US$250. Non-warranty repairs above Euro/US$250 generally require that a purchase order be issued to SBS Technologies for the amount of the repair before repairs are undertaken.

The customer in addition to repair cost pays the shipping freight.

Procedure

In the event of repair, please return the product together with additional information. Please use the error report at the end of this manual and fill in:

• Description of the type of defect.

• Is the defect restricted to certain environmental conditions?

• What was the hardware environment before the defect appeared?

• Where there input signals? If yes, which?

• Please specify ‘warranty’ or ‘no warranty’ repair.

You may use the report form at the end of this manual for this purpose.

Please use the original packing material for shipping to avoid damage.

Otherwise warranty may be lost.

To expedite assistance for problems, also provide the following:

• Your Name, Phone and Company.

• Product with which you are having trouble.

• Serial Number, Part Number and Revision.

• Hardware environment the product is used.

• Operating system you are running.

• Detailed description of your problem and any error messages that have appeared on the screen.

• The name of a technically qualified individual at your company familiar with the product failure.

Depending on the circumstances of the problem, it may be deemed necessary to return the product to SBS Technologies for repair. In order to return the product for repair, the following steps are necessary:

• Obtain a Return Material Authorization number (RMA#) from SBS

Customer Support.

• Ship the product prepaid to the designated repair point.

• Provide a written description of the claimed defect with the product.

Obtaining an RMA Number

To obtain a product Return Material Authorization number (RMA#), you should call our Customer Service department through our main number.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 103

Shipping the Product

Any product returned to SBS should be in its original shipping carton if possible. Otherwise the product should be carefully packed in a conductive

(ESD) packing material and placed in a cushioned corrugated carton suitable for shipping.

Please mark the shipping label with the RMA number and return it to:

EU US

SBS Technologies GmbH & Co. KG

RMA# (put RMA here)

Memminger Strasse 14

86159 Augsburg

Germany

Customer Service Dept.

ATTN: RMA# (put RMA here)

SBS Technologies, Inc.

7401 Snaproll St., NE

Albuquerque, NM 87109

U.S.A.

Note:

Returns in the US and associated regions should be sent to the office where products were bought. See separate address list of office, support and RMA addresses.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 104

Albuquerque, USA

(Corporate)

Augsburg, D

Mansfield, USA

Newark, USA

Raleigh, USA

Shenzhen, CN

St. Paul, USA

Waterloo, CDN

Error Report Form

SBS Technologies Inc.

7401 Snaproll St., NE

Albuquerque, NM 87109

U.S.A.

SBS Technologies GmbH &

Co. KG

Memminger Str. 14

86159 Augsburg

Germany

SBS Technologies Inc.

603 West Street

Mansfield, MA 02048

USA

SBS Technologies Inc.

8371-C Central Avenue

Newark, CA 94560

USA

SBS Technologies Inc.

6301 Chapel Hill Road

Raleigh, NC 27607

USA

SBS Technologies

Room 501-502

Cyber Times Tower B

Tianan Cyber Park

Futian District

Shenzhen 518041

P.R. China

SBS Technologies Inc.

1284 Corporate Center Drive

St. Paul, MN 55121-1245

USA

SBS Technologies Inc.

101 Randall Drive

Waterloo, ON N2V 1C5

CDN

Phone: +1-505-875-0600

Fax: +1-505-875-0400

Email: [email protected]

Phone: +49-821-5034-170

Fax: +49-821-5034-119

Email: [email protected]

Phone: +1-508-261-7007

Fax: +1-508-261-1420

Email: [email protected]

Phone: +1-510-742-2500

Fax: +1-510-742-2501

Email: [email protected]

Phone: +1-919-851-1101

Fax: +1-919-851-2844

Email: [email protected]

Phone: +86-755-8347-5668

Fax: +86-755-8347-6535

Email: [email protected]

Web: http://china.sbs.com

Phone: +1-651-905-4700

Fax: +1-651-905-4701

Email: [email protected]

Phone: +1-519-880-8228

Fax: +1-519-880-8118

Email: [email protected]

When you are returning a product for repair, it is very important to include a written report which details the nature of the problem in order to expedite the repair. Please always use the Error Report Form attached at the end of this manual or include the following information:

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 105

• RMA Number, if applicable

• Product & Serial Number

• Part Number

• Version

• BIOS built date a

• Contact: Name & Phone Number

• Detailed Description of the Problem/Defect a

The BIOS built date can be found on the BIOS boot up summary. Please get into BIOS SETUP and deselect the quick boot option in the BOOT menu.

Example/coding of the ID line:

62 – 0102 – 004199 – 00101111 – 071595 - E7501 – VR9 - Y2KC-0 year

AMIBIOS core copyright date major & minor BIOS revisions processor, flash ROM size

You can stop the video output for proper reading the three information lines as described: Simply press the “0 / Enter” key during the start-up sequence.

This key is located on the numeric keypad of your keyboard.

SBS Technologies – CR9, CP9, CT9 Hardware User’s Manual, Edition 2.6 Page 106

Error Report Form (EU)

SBS Technologies GmbH & Co. KG

Memminger Str. 14

86159 Augsburg

Germany

Phone Number +49 821 5034-170

Fax Number +49 821 5034-119

Company Name

Department

Contact Person

Mailing Address

Phone Number

Fax Number

Email Address

RMA# _______________

Part. No.

____________

Version

__ . __

Date

__ __ __

Serial No.

______________

Error Description:

Hardware Environment:

Operating System/Software:

Warranty repair: ‰ YES ‰ NO (Please see section ‘Warranty’)

Error Report Form (US)

SBS Technologies, Inc.

Phone Number +

Fax Number +

Company Name

Department

Contact Person

Mailing Address

Phone Number

Fax Number

Email Address

RMA# _______________

Part. No.

____________

Version

__ . __

Date

__ __ __

Serial No.

______________

Error Description:

Hardware Environment:

Operating System/Software:

Warranty repair: ‰ YES ‰ NO (Please see section ‘Warranty’)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement