Allen-Bradley 140G-K-CEAA Installation Manual
Allen-Bradley 140G-K-CEAA is an auxiliary contact for LSIG-D-MM wired (1AX+1AL) for 140G-K. It is used for electrical signaling of circuit-breaker open or open due to trip. The device has the following capabilities:
- Electrical signaling: The 140G-K-CEAA can be used to send an electrical signal to indicate that a circuit breaker is open or has tripped. This can be used to trigger an alarm or to shut down other equipment in the event of a power failure.
- Wired connection: The 140G-K-CEAA is wired directly to the circuit breaker, making it easy to install and maintain.
- Compact design: The 140G-K-CEAA is compact in size, making it easy to fit into tight spaces.
Advertisement
Advertisement
140G-K-CEAA, 140G-M-CEAA
Auxiliary contacts for LSIG-D-MM wired (1AX+1AL) for 140G-K, 140G-M
Contatti ausiliari per LSIG-D-MM cablati
Hilfskontakte für LSIG-D-MM, verdrahtet
Contacts auxiliaires pour LSIG-D-MM câblés
Contactos auxiliares para LSIG-D-MM cableados
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
Bul. 140G/140MG
1 2 140G-K
DIR 1000436R0606 (L2518)
CLACK
3 140G-M
4 140G-M
5 140G-K
6 140G-M
DIR 1000436R0606 (L2518)
(2)
7 140G-M
8
9 140G-K 10 140G-K
DIR 1000436R0606 (L2518)
(3)
11 140G-K 12
10.62 lb-in
1.2 Nm
140G-M
13 140G-M 14 140G-M
DIR 1000436R0606 (L2518)
(4)
10.62 lb-in
1.2 Nm
15 16 140G-K
17 140G-M 18
XA connection located on trip unit
140G-K
XA connection located on trip unit
DIR 1000436R0606 (L2518)
(5)
19 140G-M 20 140G-K
21
9.73 lb-in
1.1 Nm
140G-K 22 140G-M
DIR 1000436R0606 (L2518)
(6)
17.7 lb-in
2 Nm
23 140G-M 24
DIR 1000436R0606 (L2518)
(7)
25
TO XA CONNECTION
ON ELECTRONIC
TRIP UNIT
X8
AX
X6
AL
11
12
95
98
AL/AX For Comm.
1406-K-CEAA or
140-M-CEAA
LEGEND - LEGENDA - ZEICHENERKLÄRUNG - LEGENDE - LEYENDA
AX = Contact for electrical signalling of circuit-breaker open
AX = Contatto per la segnalazione elettrica di interruttore aperto
AX = Kontakt für die elektrische Anzeige der Ausschaltung des Leistungsschalters
AX = Contact pour la signalisation électrique de disjoncteur ouvert
AX = Contacto para la señalización eléctrica de interruptor abierto
AL = Contact for electrical signalling of circuit-breaker open due to trip
AL = Contatto per la segnalazione elettrica di interruttore aperto per intervento degli sganciatori (posizione di scattato)
AL = Kontakt für die elektrische Anzeige der Ausschaltung des Leistungsschalters wegen Auslösung der thermomagnetischen Auslöser
(Ausgelöst-Stellung)
AL = Contact pour la signalisation électrique de disjoncteur ouvert pour fonctionnement des déclencheurs (position déclenché)
AL = Contacto para la señalización eléctrica de interruptor abierto para intervención de los relés (posición de disparo)
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN011-MU-P - April 2013
DIR 1000436R0606 (L2518)
Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved.

Public link updated
The public link to your chat has been updated.
Advertisement