Network Camera FLC-1301A, FXC-1302A - C-Tac

Network Camera FLC-1301A, FXC-1302A - C-Tac
Network Camera
FLC-1301A, FXC-1302A
User Manual
V3.0.0
1
User Manual of Network Camera
2
User Manual of Network Camera
Safety Instructions
• Read these safety instructions and the operation manual first before you install and commission
the camera.
• Keep the manual in a safe place for later reference.
• Protect your camera from contamination with water and humidity to prevent it from permanent
damage.
Never switch the camera on when it gets wet. Have it checked at an authorized service center in
this case.
• Never operate the camera outside of the specifications as this may prevent the camera
functioning.
• Do not operate the cameras beyond their specified temperature, humidity or power ratings.
Operate the camera only at a temperature range of -10°C to +50°C and at a humidity of max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.
• Pay attention when laying the connection cable and observe that the cable is not subject to heavy
loads, kinks, or damage and no moisture can get in.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open. This can destroy the sensor.
• Installation, maintenance and repair have to be carried out only by authorized service centers.
Before opening the cover disconnect the unit from mains input.
• The fitter is responsible for the system of protection being followed in accordance with the
technical data, e.g. by sealing of the cable outlet with silicone.
• Contact your local dealer in case of malfunction.
• Only use original parts and original accessories from Videor E. Hartig GmbH.
• Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean the
dome surface.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
• During assembly, care must be taken to ensure that existing seals are correctly inserted and are
not displaced as a result of assembly.
You must not continue to use damaged seals.
3
User Manual of Network Camera
NOTE: This is a class A digital device. This digital device can cause harmful interference in a
residential area;
in this case the user may be required to take appropriate corrective action at his/her
own expense.
4
User Manual of Network Camera
Table of Contents
Chapter 1 Introduction........................................................................................................................... 1
1.1 Network camera Functions and Features ................................................................................. 1
1.2 Applications............................................................................................................................... 1
1.3 Package Contents ...................................................................................................................... 2
Chapter 2 Installation ............................................................................................................................. 3
2.1 Camera Description ................................................................................................................... 3
2.1.1 Camera Physical Description ........................................................................................... 3
2.1.3 Camera Connection......................................................................................................... 4
2.2 Hardware Installation ................................................................................................................ 5
Chapter 3 Network Camera Connection ................................................................................................ 7
Chapter 4 Network Access ..................................................................................................................... 9
4.1 Access over IE Browser.............................................................................................................. 9
4.1.1 Live View ....................................................................................................................... 10
4.1.2 Parameters Configuration ............................................................................................. 12
4.2 Access over Client Software .................................................................................................... 23
4.2.1 Client Software Installation ........................................................................................... 23
4.2.2 Live View ....................................................................................................................... 25
4.2.3 Camera Parameters Configuration ................................................................................ 29
Chapter 5 Access over Internet ............................................................................................................ 32
5.1 Access network camera with static IP .............................................................................. 32
5.2 Access network camera with dynamic IP ......................................................................... 33
Chapter 6 Specifications and Drawings................................................................................................ 37
6.1 Specifications ................................................................................................................... 37
6.2 Dimensional Drawings ..................................................................................................... 39
Appendix 1 SADP Introduction............................................................................................................. 40
Appendix 2 Port Map ........................................................................................................................... 42
Appendix 3 Pin Definition .................................................................................................................... 44
1
User Manual of Network Camera
Chapter 1 Introduction
Network camera is a kind of embedded digital surveillance product that combines the features
of both traditional analog camera and network DVS (Digital Video Server). Due to the embedded
Linux operation system and the latest Davinci hardware platform of TI, the system operates with
high scheduling efficiency. Furthermore, the firmware is burned in the flash, which makes the
product small, reliable and highly stable.
1.1 Network camera Functions and Features
Functions:
‹ Network Function: Support the TCP/IP protocols and IE browsing.
‹ Heartbeat Function: The server can acquire real time operating performance of the network
camera through the heartbeat function.
‹ Alarm Function: Supports Motion Detection, Storage exception.
‹ User Management: Support multilevel right management. The administrator can create up to
15 separate users with different right levels, which highly improves the system security.
Compression Functions:
‹ Support 1 channel video signal and standard H.264 encoding compression, which supports both
variable bit rate and variable frame rate; besides, you can self-define both the video quality and
its compressed bit rate.
Remote Control:
‹ The product offers a 10M/100M self-adaptive Ethernet interface.
‹ Support TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP protocols.
‹ Set the parameters, browse real time videos or check the camera performance by software or
IE, and store the compressed bit rate through network.
‹ Support remote upgrades and maintenance.
1.2 Applications
This camera is ideal for remote control network applications. E.g.:
1. Network surveillance for supermarkets and factories.
2. Remote surveillance for homes and offices.
3. Indoor monitoring scenes, such as hotel, corridor, stairway.
2
User Manual of Network Camera
1.3 Package Contents
1.
2.
3.
4.
5.
6.
Camera × 1
Bracket × 1
User Manual × 1
Quick Start Guide × 1
Installation Guide × 1
CD × 1
3
User Manual of Network Camera
Chapter 2 Installation
NOTE:
1. Please check if all the items on the package list have been included with your camera.
2. Read the following contents carefully before the installation.
3. Make sure that all the related equipment is power-off during the installation.
4. Check the power supply to prevent any damage caused by mismatching problems.
5. If the product does not operate properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. Users are responsible for any
problem caused by modification or repairing without authorization.
2.1 Camera Description
2.1.1 Camera Physical Description
8
5
6
9
10
2
1
3
4
7
4
User Manual of Network Camera
Serial NO.
Description
1
Microphone hole
2
Micro SD card solt
3
LINK: Network status LED indicator.
When the network is connected, the LED flickers in green.
4
Power LED indicator, which turns red when power is applied to the unit
5
Lens
6
ETHERNET: 10M / 100M self-adaptive Ethernet interface
7
RESET: Reset all parameters to factory default settings
8
Speaker hole
9
Power supply
10
Bracket mounting holes, used to fix the camera to the bracket
NOTE:
When the camera is power up, press the ‘RESET’ button for about 10 seconds, then all parameters,
including user name, password, IP address, port number, etc., will be reset to the factory default
settings.
2.1.3 Camera Connection
Step1:
Connect one end of the network
cable to the camera and the other
end to PC.
Step2:
Connect one end of the power cord
to the camera and the other end to
power socket to supply power for
the camera.
Step3:
Access the camera over IE or client
software to view live video images.
5
User Manual of Network Camera
2.2 Hardware Installation
Cube camera can be fixed in both wall and ceiling, customers can choose different ways to install
the camera according to their specific needs. The following section introduces the ceiling mounting,
and the wall mounting follows the same way:
Step 1: Fix the camera mounting bracket to the ceiling.
Fig 2.2.1 Fix camera mounting bracket
NOTE:
If it is wall, you need to fix the expand bolt (note: the mounting hole of the expand bolt should align
with the bracket) before fixing the bracket as ① in Fig 2.2.1 . If the wall surface is wooden, the part
of ① in Fig 2.2.1 can be ignored and you can use the self-tapping screw to directly fix the bracket.
Please note that the wall on which the camera is fixed should be able to bear at least three times
the weight of the bracket and the camera.
6
User Manual of Network Camera
Step 2: Screw the mounting hole to the mounting bracket, and then adjust the camera to the
desired monitoring location and finally tighten the knob on bracket to secure the camera to the
ceiling.
Fig 2.2.2 Fix the Camera
Step 3: Viewing the video on the computer, if the scene is not that you want to monitor, loosen the
knob on the mounting bracket and adjust the camera lens to the desired monitoring scene, and
finally tighten the knob on bracket.
Fig 2.2.3 Done
7
User Manual of Network Camera
Chapter 3 Network Camera Connection
Two methods can be used to connect between network camera and PC, shown as below:
Fig. 3.1 Cross Line Connection
Fig. 3.2 Direct Line Connection
Before visiting network camera over network, user should acquire its IP address first. SADP is a
software tool which can automatically detect network device in the LAN and give the device’s
information like IP address, mask, port number, device serial number, software version, etc., shown
as Fig. 3.3.
8
User Manual of Network Camera
Fig. 3.3
Select the device, and set its IP address and mask at the same network segment with the PC.
For the detailed introduction of SADP, please refer to Appendix 1.
Note: The network camera is set with the factory default IP address of “192.0.0.64”, the port of
“8000”, the super user name of “admin” and the password of “12345”.
9
User Manual of Network Camera
Chapter 4 Network Access
After hardware installation, user can view live video and configure parameters for the network
camera, including IP address, subnet mask and port number, etc. The following two methods can be
used to access the camera:
1. View live video and configure parameters over IE browser.
2. View live video and configure parameters over client software.
4.1 Access over IE Browser
Before access to the camera over IE
browser, user should adjust the security
level.
Open the IE browser, and set the
security level to Medium in Tools/
InternetOptions/Security/Custom
Level..., and enable or prompt Activex
Control and Plug-in directly as well.
Fig. 4.1.1 Adjust the Security Level
10
User Manual of Network Camera
4.1.1 Live View
Step 1: Install Active-X Control
Type the IP address of the network
camera and press Enter, then the
ActiveX mention dialog will pop
up.
Click Install to install the ActiveX
control.
Fig. 4.1.2 Install the ActiveX Control
Step 2:
Input the Username (default:
admin), Password (default: 12345)
and Port (default: 8000) of the
camera, and then click [Login].
Fig. 4.1.3 Login Interface
11
User Manual of Network Camera
Step 3:
After successful login, user is allowed to view the live video. Refer to Figure 4.1.4.
Fig. 4.1.4 Live View Page
Icons on Live View Page:
Icon
Description
Full-screen display mode
Exit full-screen display mode
Start Preview
Stop Preview
Capture Picture
Start/Stop Record
Digital Zoom
Video Parameters
12
User Manual of Network Camera
Digital Zoom:
Click mouse in the desired position of live video image and scroll the mouse to realize zoom in and
zoom out function.
Video Parameters:
Icon
Description
Brightness: 0~100 configurable
Contrast: 0~100 configurable
Saturation: 0~100 configurable
Hue: 0~100 configurable
Gain: 0~100 configurable
Exposure time: 0~40000
configurable
Restore default
Fig. 4.1.5 Video Parameters
4.1.2 Parameters Configuration
Click Configuration to enter the Parameters Configuration interface.
4.1.2.1 Local Configuration
Fig. 4.1.6 Local Configuration
13
User Manual of Network Camera
Local Configuration:
Parameters
Description
Protocol type
TCP and UTP selectable
Stream type
Main stream and Sub stream selectable
Display mode
Full-screen, 4:3 mode, 16:9 mode or adjustable to resolution
Package file size
128M, 256M, 512M selectable
Transmission
performance
Shortest delay mode, good real-time, normal real-time and fluency
and good fluency options selectable
Save record file as
The default directory for saving record files is C: \OCXRecordFiles,
which can be modified by user
Save captured
picture as
The default directory for saving captured files is
C:\OCXBMPCaptureFiles, which can be modified by user
4.1.2.2 Remote Configuration
Basic Information:
In the Basic Information
settings interface, user is
allowed to set the Device
Name and Device ID, as well as
view the information of IP
camera, including Device
Description, Device Location,
MAC address, Device Type,
Device SN, Firmware Version,
and U-boot Version.
Fig. 4.1.7 Basic Information
14
User Manual of Network Camera
Channel Parameters Æ Display
Setting:
According to different
requirements, enable the
display of Date&Time and
Week by clicking the checkbox.
Different date formats can be
selected.
The OSD Status can be set to
transparent & flickering,
transparent & unflickering,
nontransparent & flickering, or
nontransparent & unflickering.
Fig. 4.1.8 Display Settings
Channel Parameters Æ Video Settings:
Fig. 4.1.9 Video Settings
15
User Manual of Network Camera
Parameter
Description
Stream type
Select stream type to Main stream or Sub stream
Resolution
Select the resolution for your need,
Image Quality
Select image quality to Highest, High, Medium, Low, Lower or Lowest
Bitrate Type
Select the bitrate type to Constant bitrate or Variable bitrate
Max. Bitrate
Select or custom bitrate according to the resolution
Frame Rate
Select a proper frame rate for the corresponding resolution.
Multicast
Set the multicast address, with the default multicast of 0.0.0.0
RTSP Port
Set the RTSP port, with the default RTSP port of 554
Mirror
Change the left and right direction of the picture, like mirror
Flip
Rotate the picture 180°. Change the bottom of the picture to the top
Channel Parameters Æ
Motion Detection Setting:
Select the checkbox of Enable
motion detection to enable this
function.
Zone Settings:
Click Start draw button to draw
motion detection zone by
clicking and dragging the
mouse in the live video image.
User is allowed to draw
multiple motion detection
zones in the same picture.
When all zones have been set,
click Stop draw to finish
drawing.
Sensitivity:
The sensitivity level can be set
to 0, 1, 2, 3, 4 and 5. When it is
set to 0, the sensitivity is
disabled.
Linkage:
The Linkage method can be
selected to either Email link or
Trigger alarm output.
Fig. 4.1.10 Motion Detection Zone Settings
Fig. 4.1.11 Motion Detection Linkage Settings
16
User Manual of Network Camera
Channel Parameters Æ Text
Overlay Setting:
Input the characters in the Text
Information box and define the
OSD location in the image by
setting the XPosition and
YPosition, and then select the
checkbox of OSD Text. After
clicking Save to finish the
settings, the defined title will
be displayed on the image.
Note:
The values of XPosition and
YPosition refer to the position
relative to the origin as the
upper left corner of the image.
Fig. 4.1.12 Text Overlay Settings
Network Parameters Æ
Network Setting:
Set the IP Address, Subnet
Mask, Gateway and DNS Server
of the network camera.
Fig. 4.1.13 Network Settings
17
User Manual of Network Camera
Network Parameters Æ
PPPOE Setting:
Click the checkbox of Enable
PPPOE to enable this
function.
Input the PPPOE user name
and password in the text box
and then click Save to finish
settings. After reboot, the
camera will obtain a public IP
address.
Fig. 4.1.14 PPPOE Settings
Network Parameters Æ DDNS
Setting:
Click the checkbox of Enable
DDNS to enable this function.
The protocol type can be set to
DynDNS.
Fig. 4.1.15 DDNS Settings
If the protocol type is selected to
DynDNS, please input the Server
Address, e.g., members.dyn dns.
org.
Port option is reserved and not
configurable.
The User Name and Password
refer to the user name and
password registered in the
DynDNS website.
The Domain Name refers to the
domain name applied in the
DynDNS website.
Fig. 4.1.16 DynDNS Settings
18
User Manual of Network Camera
Network Parameters Æ NTP
Setting:
Click the checkbox of Enable
NTP to enable this function.
Input the Server Address and
Port of NTP.
If the public network is
applied, please input the NTP
Server Address with provision
of time sync service, e.g.,
210.72.145.44.
In the private network is
applied, the NTP software can
be used to establish NTP server
to achieve time
synchronization.
Fig.4.1.17 NTP Settings
Network Parameters Æ E-mail
Setting:
Through E-mail settings, the
alarm message can be sent to
the designated E-mail address
when alarm event occurs.
Input the SMTP server, SMTP
port, user name, password,
E-mail sender and receiver, JPEG
can be attached in this mail by
activating Attachment option,
and finally click Save to finish
E-mail settings.
Fig. 4.1.18 E-mail Settings
Alarm Parameters Æ Alarm
Input Setting:
Set the type of Relay Status
to NC or NO.
The Linkage method can be
selected to E-mail link or
Trigger alarm output.
Fig. 4.1.19 Alarm Input Settings
19
User Manual of Network Camera
Alarm Output Æ Alarm Output
Setting:
The Output Delay refers to the
length of time that the relay
remains in effect after alarm
occurs. The output delay time
can be set to 5sec, 10sec,
30sec, 1min, 2min, 5min, 10min
or Manual (manually disable).
Fig. 4.1.20 Alarm Output Delay Settings
Alarm Deployment Time:
The Deployment time can be set
to a day of the week or to all
week, with a period configurable
for each day.
Note: The alarm deployment
time setting is valid only when
the camera has already been
configured with the motion
detection, alarm input and alarm
output functions.
Fig. 4.1.21 Alarm Deployment Time Settings
User Management:
Fig. 4.1.22 User Management
When the current login user is admin, it is allowed to create other users. Up to 15 users can be
created. Refer to Fig. 4.1.22.
20
User Manual of Network Camera
Add User:
Click Add to enter the
settings interface as
shown in Fig. 4.1.23.
Input the user name,
password, IP address,
MAC address, and then
select user type. Finally,
click OK to finish the user
addition.
Modify User:
Click Modify to enter the
settings interface as shown
in Fig. 4.1.24.
It is allowed to modify the
user name, password, IP
address, MAC address, and
then select user type.
Finally, click OK to finish the
user modification.
Note: The user admin can
only be modified with its
password.
Fig. 4.1.23 Add User
Fig. 4.1.24 Modify User
Remote Upgrade:
Click Browse to select the
local update file and then
click Upgrade to finish
remote upgrade.
Fig. 4.1.25 Remote Upgrade
21
User Manual of Network Camera
Restore Default:
Select Full Mode or Basic
Mode to restore the default
settings.
Note:
The Full Mode refers to
restore all parameters to the
factory default settings.
The Basic Mode refers to
restore the parameters to
factory default settings
except IP address, subnet
mask, gateway and port.
Fig. 4.1.26 Restore Default
Reboot Device:
Click OK to reboot the
network camera.
Fig. 4.1.27 Reboot Device
22
User Manual of Network Camera
4.1.2.3 Advanced Configuration
Note: This chapter is applicable to professional configuration.
1: Input the IP address of the
network camera and “config”
(Such as http://171.9.9.77/config),
and then click [Enter].
2: Type the Username (default:
admin), Password (default: 12345)
and Port (default: 8000) of the
camera, and then click [Login].
3: The “Remote config” dialog will
pop up, which has more advanced
settings including schedule record
and HDD settings and so on.
Please refer to “FINITRA_en_93172.pdf” for a more detailed parameters configuration. You can find
the document in the PC Operating System after the installation of eneo FINITRA by selecting
“Start”-> “All Programs”-> “eneo FINITRA”.
23
User Manual of Network Camera
4.2 Access over Client Software
4.2.1 Client Software Installation
Note:
It is recommended to use the computer adopting INTEL P3, P4, C4, Core4 CPU, and the Intel chipset
motherboard of well-known brands (Asus, Gigabyte, MSI, ECS, and INTEL etc.) to ensure the stability
of the system. After testing, the following models of the current graphics cards support the
installation of the client software: ATIRadeonX1650, X1600, X1550, X1300, X800, X600, X550,
HD2400, HD2600, NVIDIA GeForce 8600GT, 8500GT, 8400GS, 7600, 7300LE, 6600LE, 6200LE, and
INTEL915/945G. And the graphics driver must support hardware scaling function.
Step 1:
Double click ‘eneo FINITRA.exe’ in the
Windows Operating System. The
‘Preparing Setup’ dialog box will
automatically pop up as shown Fig.4.2.1.
Fig. 4.2.1 Client Software Installation
Step 2:
Input the User Name and Company
Name, and then click Next.
Fig.4.2.2 Customer Information
24
User Manual of Network Camera
Step 3:
Select the destination folder and click
Next to enter the next step.
Fig. 4.2.3 Ready to Install the Program
Step 4:
Click Install to start installation till
finishing the installation.
Fig. 4.2.4 Installation
25
User Manual of Network Camera
Step 5:
Click Finish to close the dialog box.
Fig. 4.2.5 Done
After the client software has been installed, you can find the remote client software through Start->
Programs from your PC.
4.2.2 Live View
After the installation of eneo FINITRA, there is a short-cut icon named “eneo FINITRA” on
computer’s desktop. Please double click “eneo FINITRA” to run the software.
Step 1:
Used for the first time:
User needs to register an administrator if
the software is used for the first time.
Input User name, Password, Verification,
and click OK, then user can log in as the
administrator.
Fig. 4.2.6 Register Administrator
26
User Manual of Network Camera
User login:
Input User, Password and click Login to
enter the GUI window of the software.
Fig. 4.2.7 User Login
Fig. 4.2.8 GUI window of the software
Step 2:
Click Setup to enter the configure
mode, and then click Device
Management.
Fig. 4.2.9 Device Management
27
User Manual of Network Camera
Step 3:
Right click the left area, and then click
Add Area.
Input Area Name for your need, and
then click OK to add area.
Fig. 4.2.10 Add Area
Step 4:
Right click the area that you add, and
then click Add Device to add network
camera.
Input “Device Name” for your need.
Select “Normal IP” from Register Mode.
Input network camera’s IP in Device IP,
e.g. 192.0.0.64, Port: 8000, User Name:
admin, Password: 12345.
Enter the number of cameras in
“Channel No.” field, e.g. enter 4 for
FNR-4004 NVR. “Multicast Address’ is
optional and used for media
broadcasting (D type IP address).
Finally, click OK to finish settings.
Fig. 4.2.11 Add Device
28
User Manual of Network Camera
Fig. 4.2.12 Camera Adding Completed
Step 5: Click the Preview, and then double click the device name in the left tree to view the live
video.
Fig. 4.2.13 Preview
29
User Manual of Network Camera
4.2.3 Camera Parameters Configuration
NOTE:
Different types of network cameras maybe have different configuration parameters in the interface
of “Config Sensor Parameters”. This section takes a type of network camera for example to
introduce configuration parameters in the interface of “Config Sensor Parameters”. If the
information in the actual interface of “Config Sensor Parameters” is not different from the
information shown in this section, then subject to the actual interface information.
For viewing better image, you can set the parameters of the camera, and operate as following:
Step 1:
Right click in the preview window, and
click [Config Sensor Parameters…], then
the [Config Sensor Parameters…] box will
pop up.
Fig. 4.2.14 Sensor Parameters
Step 2: Video Parameters Configuration
Adjust the value of “Brightness”, “Contrast”,
“Saturation”, “Hue”, “Sharpness” and
“Gain” for your need, which can be set
from 1 to 100.
Fig. 4.2.15 Video Parameters
30
User Manual of Network Camera
Step 3: White Balance Configuration
Select the mode to Auto1 or Off for your
need.
Fig. 4.2.16 White Balance
Step 4: Exposure Configuration
Select “Exposure time” and “Iris mode” for
your need.
Fig. 4.2.17 Exposure
Step 5: Day/Night Mode Configuration
Select “Day”, “Night” or “Auto” mode in
Mode and adjust the value of “Day->Night”,
“Night->Day”, and “Filter time” for your
need.
Fig. 4.2.18 Day/ Night Mode
31
User Manual of Network Camera
Step 6: Other Parameters Configuration
Select the value of “Power Line”, “Mirror”,
“E-PTZ” and “Local Output”.
Fig. 4.2.19 Other Parameters
Please refer to “FINITRA_en_93172.pdf” for more detailed parameters configuration. You can find
the document in the PC Operating System after the installation of eneo FINITRA by selecting
“Start”-> “All Programs”-> “eneo FINITRA” -> “eneo FINITRA.exe”.
32
User Manual of Network Camera
Chapter 5 Access over Internet
5.1 Access network camera with static IP
When there is a static IP from an ISP, open some ports (such as 80 and 8000 ports) in the router.
Then a user can visit it through a web browser or client software via the internet. The steps for port
forwarding are different for each model of router. Please call the router manufacturer for assistance
with port forwarding or visit www.portforward.com.
Note: Refer to Appendix 2 for a detailed explanation about Port Map.
Users can directly connect the network camera to the internet without using a router.
Fig. 5.1 Access IPC through Router with Static IP
Fig.5. 2 Access IPC with Static IP directly
For the client software to view the camera, in the adding equipment column, select the normal
model, and then fill in the IP info.
33
User Manual of Network Camera
Fig. 5.3 Selecting Normal IP
5.2 Access network camera with dynamic IP
Fig. 5.4 Access IPC through PPPoE Dail-up
This camera supports the PPPoE auto dial-up function, connecting the camera to a Modem for
dial-up access to an ADSL network to get a public IP address; First, through local network access to
the network camera, select “Configure ”Æ” Right Click the Device”, “Remote Configuration”, and
finally select “PPPoE Settings” under “Network Paramters” to fill in the PPPoE user name and
password and confirm the password. Please restart the network camera after completion of
configuration. Then the network camera can obtain a dynamic IP from an ISP operation business.
However, the obtained IP address is dynamically assigned via PPPoE, so the IP address always
changes accompanied with modem rebooting.
34
User Manual of Network Camera
Fig. 5.5 PPPoE configuration Dialog box
It is inconvenient to view a network camera with a dynamic IP, therefore, users should register with
a dynamic DNS service provider. (Such as DynDns.com)
Domain name resolution contains normal domain name resolution and private domain name
resolution. First, we will introduce normal domain name resolution.
1. Normal Domain Name Resolution
Fig. 5.6 Normal Domain Name Resolution
35
User Manual of Network Camera
Apply a domain name from a domain name provider, then view the camera via the applied domain
name. If the camera connects to the internet via a router, users should port forward the router.
Please refer to Appendix 2.
Input domain names in the client software or IE to view the network cameras. Take the client
software configuration as an example.
Fig. 5.7 Selecting Normal Domain Mode
2. Private Domain Name Resolution
Fig. 5.8 Private Domain Name Resolution
36
User Manual of Network Camera
A PC with a static IP which is running the domain name resolution service is necessary.
When the network camera connects to the internet through PPPoE and obtains an IP address, it will
send its name and IP address to the resolution server. When the client software connects to the
network camera, it will connect to the resolution server and tell the resolution server the expected
camera’s name. And the server will find the camera from all the registered cameras and send its IP
address to the client software. Once the client software gets the IP address, it can connect the
network camera.
Fig. 5.9 Selecting Private Domain Mode
37
User Manual of Network Camera
Chapter 6 Specifications and Drawings
6.1 Specifications
Type
Art. No.
Series
Resolution standard
System
Sensor size
Imager
Sensitivity (at 50% video signal)
Digital Noise Reduction (DNR)
Low speed shutter
Wide Dynamic Range (WDR)
Backlight compensation
IR cut filter
Privacy zones masking
Activity detection
Motion detector
Text display
Menu languages
Audio support
Audio
Alarm inputs
Alarm outputs
Internal storage
Digital storage media
Compression standard
Resolution max.
Resolution
Image transmission rate max.
Stream types
Ethernet interface
FLC-1301A
203661
FXC-1302A
203613
eneo F
SD
day&night
1/3"
CMOS
0.1 Lux, (colour);
0.01Lux (B&W) at F1.2
0.5 Lux at F1.2
no
yes, 1/25sec. ~1/100,000sec.
no
no
OLPF (Overlay Low Pass Filter)
4 areas selectable
yes
integrated motion detector
supplied
English, Chinese
yes
Built-in microphone, speaker
Micro SD card, SDHC card, SD card
Apacer 1GB, 4GB, 8GB, 16GB; Kingston 1GB, 2GB, 4GB,
8GB, 16GB, 32GB; ScanDisk 1GB, 2GB, 4GB, 8GB, 32GB;
Crucial 1GB; Trancend 4GB, 8GB, 16GB; KINGMAX 4GB,
8GB, 16GB; A-Data 4GB, 16GB
H.264, MJPEG
640 x 480
1600 x 1200
VGA
2 megapixels
30 pictures/sec.
H.264, MJPEG multiple
100Base-TX
38
User Manual of Network Camera
Type
Art. No.
Web browser
Network protocols
Remote configuration
Lens type
Lens mount
Focal length
Digital zoom
PTZ support
Serial interfaces
Password protection
Management Software Support
SDK
ONVIF
Power consumption
Temperature range (operation)
Colour (housing)
Housing material
Supply voltage
Power over Ethernet
Protection rating
Integrated wall mount
Hidden cable management
Sunshield
Window heater
Vandalism resistant
Certificates
Parts supplied
Weight
Dimensions (HxWxD)
FLC-1301A
FXC-1302A
203661
203613
MS Internet Explorer vers. 7.0 or higher
TCP/IP, HTTP, DHCP, DNS, DDNS, RTP, RTCP, PPPoE, FTP,
SMTP, NTP, SNMP, HTTPS, SIP, IPv4, IPv6
via web browser, remote software
fixed focal length
M12
4mm
no
yes
no
yes
Finitra, Zelaris
Available, SDK incl. HTTP-API and ActiveX
core specifications 1.02
3W
-10°C ~ +60°C
RAL9010
plastic
5VDC, PoE (IEEE-802.3af)
yes
n/a
yes
no
no
no
no
CE
lens, PSU
250 g
see drawings
Optional Accessories
The optional accessories currently available can be found on our Homepages: www.videor.com and
www. eneo-security.com
39
User Manual of Network Camera
6.2 Dimensional Drawings
33
70.4
59.4
110
1/4 20UNC
Dimensions: mm
40
User Manual of Network Camera
Appendix 1 SADP Introduction
1. Brief introduction
SADP (Search Active Devices Protocol) is a kind of software which can automatically search
network speed dome in LAN. User can modify the IP address, subnet mask and port of the
device without visiting IP address of the device. Additionally, password of the super user in this
device can be recovered as default.
SADP software needs to support SADP, so we should install WinPcap at first, which is placed at
the directory of SADP software.
2. Search active devices online
After installing WinPcap, double click sadpdlg.exe. The software will start to search active
devices in LAN, and device type, IP address, Port number, Device Serial No., subnet mask, MAC
address, the number of channels, main control and encoding version and device initiating time
are showed in the list, as following:
41
User Manual of Network Camera
3. Modify device information
Select the device that needs modification in the device list, then basic information of the device
will be demonstrated in the information column on the right. Click “modify” button to activate
IP address, subnet mask, device port editing and password validating box, as follows:
Select the device that needs modification in the device list, then basic information of the device
will be demonstrated in the information column on the right. Click “modify” button to activate
IP address, subnet mask, device port editing and password validating box, as following:
Input new IP address, subnet mask, and port number, and click “save” button. If a dialog pops up,
showing “saved successfully”, that means you have modified the configuration information; if
“saving failed” turns up, click the “cancel” button to quit it.
4. Recover default password
You can reset the password of the super user as “12345” in the case of a lost password.
Input certain validation code into the ‘Resume default password’ box, and click ‘OK’ to finish the
administrator’s password initiating.
42
User Manual of Network Camera
Appendix 2 Port Map
Note: The following setting is about TP-LINK router (TL-R410), which is maybe distinct from other
router’s setting.
1. Firstly, select the router’s WAN connection Type. As the following Fig. shows:
2. Set the “network parameter” of the router as the below figure. The setting includes subnet
mask and gateway.
43
User Manual of Network Camera
3. Set the port map in the virtual severs of Forwarding. By default, camera uses port 80, 8000, 554
and 8200. You can change these ports value with IE or client software.
The following figure gives the illustration. One camera’s ports are 80, 8000, 554, 8200 and its IP
address is 192.168.1.23. The other camera’s ports are 81, 8001, 555, 8201 and IP is 192.168.1.24.
Afterwards, enable all or TCP protocols. Enable the port map after pressing the ‘Save’.
As the settings mentioned above, map the router’s port 80 and 8000 to the network camera at
192.168.1.23; and port 81 and 8001 to the network camera at 192.168.1.24. In this way, user can
access the 192.168.1.23 through accessing the router’s port 80 and 8000.
Note: The port of the network camera cannot conflict with other ports. For example, some router’s
web management port is 80. User can amend the router’s or the camera’s port to solve this
problem.
44
User Manual of Network Camera
Appendix 3 Pin Definition
(1) UTP between the network port of camera and HUB (Direct Cable)
(2) UTP between the network port of camera and PC (Cross Cable):
45
User Manual of Network Camera
46
User Manual of Network Camera
47
User Manual of Network Camera
eneo® is a registered trademark of Videor E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
Videor E. Hartig GmbH
Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany
Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved.
© Copyright by Videor E. Hartig GmbH 06/2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement