Pharos GPS Phone 600 Series
Pharos GPS Phone 600 Series
Hardware User's Manual
GPRS / EDGE Settings for AT&T / Cingular
Step 1
Step 2
♦ Tap
Start, Settings, the
Connections tab,
Connections, and then the
Tasks tab.
♦ Tap Add a new modem
connection.
Step 3
♦ Enter a new connection name
(i.e. Cingular GPRS).
♦ Select Cellular Line (GPRS).
♦ Tap Next.
Step 4
♦ Enter Access point name
wap.cingular.
♦ Tap Next.
♦ Tap Finish.
i
GPRS / EDGE Settings for T-Mobile
Step 1
Step 2
♦ Tap
Start, Settings, the
Connections tab,
Connections, and then the
Tasks tab.
♦ Tap Add a new modem
connection.
Step 3
♦ Enter a new connection name
(i.e. T-Mobile GPRS).
♦ Select Cellular Line (GPRS).
♦ Tap Next.
Step 4
♦ Enter Access point name
wap.voicestream.com.
♦ Tap Next.
♦ Tap Finish.
ii
Table of Contents
GPRS / EDGE Settings for AT&T / CINGULAR
i
GPRS / EDGE Settings for T-Mobile
ii
Table of Contents
1
Please Read Before Proceeding
6
Important Safety Precautions
7
Chapter 1: Voice Command Satellite Navigation
1.1 Navigation Device Installation
1.2 GPS Navigation Software Installation
1.3 Conditions for Using GPS Car Navigation
9
9
10
10
Chapter 2: Getting Started
2.1 Package Contents
2.2 External Views
• Hardware Hot Key Functions
• Rear Side
2.3 Using the GPS Phone 600 for the First Time
• Charging Power and Power Supply
• Re-installation or Replacing the Battery
2.4 Power On and Off
• Sleep Mode
• Turn on the Screen
• Restarting the GPS Phone 600
• Reset
• Cold Boot
12
12
13
14
15
16
16
18
19
19
20
21
21
22
Chapter 3: Using the GPS Phone 600
3.1 Start Screen
• Today Screen
• Programs
• System Application Programs
3.2 Entering Information on Your GPS Phone 600
• Entering Text Using the Input Panel
• Typing with the Soft Keyboard
• Using Letter Recognizer
• Using Block Recognizer
• Using Transcriber
• Selecting Typed Text
• Writing on the Screen
24
24
25
27
29
31
31
32
32
33
33
33
34
1
•
•
•
•
•
•
•
•
Selecting Writing
Convert Writing to Text
Drawing on the Screen
Creating a Drawing
Selecting a Drawing
Recording a Message
Creating a Recording
Using My Text
34
35
36
36
37
37
38
39
Chapter 4: Using the Phone
4.1 Installing and Removing the SIM Card
• Installing the SIM Card and Battery
Using
the Phone
4.2
• Adjusting the Phone Volume
4.3 Turning the Phone On / Off and Making Calls
• Phone Toolbar
• Calling from Contacts
• Calling from Speed Dial
• Calling from the Call History
4.4 Customizing Your Phone
4.5 Phone Application Programs
• SIM Tool Kit
• SMS Sender
40
41
41
42
43
44
45
45
46
46
47
48
48
48
Chapter 5: Customize Your GPS Phone 600
5.1 Adjusting Settings
5.2 Notifications
5.3 Power Preference Settings
5.4 Backlight
5.5 Microphone
5.6 Adjusting the Volume
5.7 Find and Organizing Information
5.8 Navigation Bar and Command Bar
5.9 Pop-Up Menus
5.10 Redefine Hot Keys
49
49
50
51
52
53
54
55
56
57
58
Chapter 6: Using Microsoft ActiveSync
6.1 Installing and Using ActiveSync
• ActiveSync Connection Troubleshooting
6.2 USB Synchronization
• USB Synchronization
6.3 Synchronizing Using Bluetooth
59
60
61
62
62
65
Chapter 7: Connections
7.1 Connecting to the Internet
66
66
2
7.2
7.3
7.4
7.5
• Setting the GPRS / EDGE Connection
• Starting GPRS / EDGE Connection
• Disconnecting GPRS / EDGE
Using Bluetooth
• Bluetooth Connection Wizard
• Bluetooth Connection Setting
• Service
• Serial Port
• Bluetooth Headset
• FTP Sharing
CSD Type
Connecting with a Personal Computer
Wireless LAN Transmission
67
68
69
70
70
72
73
74
75
75
76
77
77
Chapter 8: Using Wireless LAN
8.1 Connecting to Wireless LAN
8.2 Configure Your Wireless Network
(Reference for a Normal Network Setup)
8.3 Configure Your Wireless Network
(Reference for Proxy Setup)
78
78
Chapter 9: Sending and Receiving Messages
9.1 E-mails and SMS Messages
• Synchronizing E-mail Messages
• Connecting Directly to the Mail Server
• E-mail Server Setup
• Using E-mails and SMS
• Direct Push Technology Alert
• Direct Push Technology Alert Settings
9.2 MSN Messenger
• Setting Up
• Working with Contacts
• Chatting with Contacts
84
84
85
86
87
88
91
91
93
94
95
96
Chapter 10: Multimedia
10.1 Using Camera
• Camera Mode
• Camera Mode Using Wizard
• Managing Pictures Shot by Continuous Shutter
• Digital Video Mode
• Digital Video Mode Using Wizard
• Speed Shooting Using the Hardware Hot Keys
10.2 FM Tuner
97
97
98
99
100
101
103
104
105
Chapter 11: Companion Programs
107
3
80
82
11.1 Calendar: Scheduling Appointments and Meetings
• Create an Appointment
• Use the Summary Screen
• Create Meeting Requests
• Schedule a Meeting
11.2 Contacts: Tracking Friends and Colleagues
• Create a Contact
• Find a Contact
• Use the Summary Screen
11.3 Tasks: Keeping a To Do List
• Create a Task
• Use the Summary Screen
Notes:
Capturing Thought and Ideals
11.4
• Create a Note
11.5 Word Mobile
11.6 Excel Mobile
• Tips for Working in Excel Mobile
11.7 PowerPoint Mobile
11.8 Windows Media Player
11.9 Internet Explorer
• Using Internet Explorer
• Browse the Internet
• View Mobile Favorites
• The Mobile Favorites Folder
• Favorite Links
• Synchronize Mobile Favorites
• Create a Mobile Favorite
• Save GPS Phone 600 Memory
108
109
110
110
110
111
112
113
113
114
115
116
117
117
118
120
122
123
124
125
125
126
127
127
128
128
128
129
Chapter 12: Maintaining the GPS Phone 600
12.1 Adding or Removing Programs
• Add Programs Using ActiveSync
• Add a Program Directly from the Internet
• Add a Program to the Start Menu
• Remove Programs
12.2 Manage Memory
• View Memory Status
• Find Available Memory
12.3 System Information
130
130
130
131
131
132
133
133
135
138
Chapter 13: Specifications
139
Appendix
A.1 Regulation Notices and Safety Declaration
• Health and Safety Information
140
140
140
4
A.2 FCC Regulations
A.3 RF Exposure Information (SAR)
• SAR Information
• Holster Information
• Where to Find Information
A.4 FAQ
142
143
143
143
144
145
5
PLEASE READ BEFORE PROCEEDING
♦ This device is not charged when you take it out of the box. When you use this
product the first time, we recommend that you install the battery as illustrated and
fully charge it for about 8 hours before use. Do not remove the battery pack when
the device is charging.
♦ Before you install the SIM card, make sure to tap the ALL OFF Button in Wireless
Manager to turn off your GPS Phone 600’s mobile phone, Bluetooth, and
wireless LAN functions. Press the “Power Button” of the GPS Phone 600 to turn
off the screen. Otherwise, disconnection problems or damage to the SIM card
may occur.
♦ When you are on a plane, in a medical facility or at a gas station where wireless
communications devices are not allowed and must be turned off, please go to
Wireless Manager and select the ALL OFF Button to turn off your GPS Phone
600’s mobile phone, Bluetooth, and wireless LAN functions. By pressing the
“Power Button” of the GPS Phone 600, you only turn off the display.
♦ In case the GPS Phone 600 is damaged, send it back to the dealer for repair. Do
not attempt to disassemble the GPS Phone 600 on your own; otherwise the
warranty will be void. Your warranty will be invalidated if you open or tamper with
the device’s outer casing.
♦ This document lists the functions, specifications, and illustrations for reference
only. Product specifications are subject to change.
6
Important Safety Precautions
When using this product the safety precautions below must be taken to offset possible
legal liabilities and damages.
Electrical Safety
This product is intended for use when supplied with power from the battery. Other
usage may be dangerous and will invalidate any approval given to this product.
Safety in Aircraft
Due to the possible interference caused by this product to an aircraft’s navigation
system and its communications network, using this product on board an airplane is
against the law in most countries.
Interference with Medical Equipment Functions
This product may cause medical equipment to malfunction. The use of this device is
forbidden in most hospitals and medial clinics.
Nonionizing Radiation
This product should be operated in the suggested normal condition only to ensure the
radioactive performance and safety of the interference. As with other mobile radio
transmitting equipment, users are advised that for satisfactory operation of the
equipment and for the safety of personnel, it is recommended that no part of the human
body be allowed to come too close to the antenna during operation of the equipment
Body-worn Operations
This device was tested for typical body-worn operations with the back of the phone kept
1.5 cm from the body. To maintain compliance with FCC RF exposure requirements,
use only belt-clips, holsters or similar accessories that maintain a 1.5 cm separation
distance between the user’s body and the back of the phone, including the antenna.
The use of belt-chips, holsters and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements, and should be
avoided.
Road Safety
Vehicle drivers in motion are not permitted to use telephony services with handheld
devices, except in the case of emergency. In some countries, using hands-free devices
as an alternative is allowed.
Environment Restrictions
Do not use this product at gas or refueling stations. The use of this product is also
prohibited in fuel storehouses, chemical plants, and locations containing explosives.
7
Safety for Environments
Do not use this product in gas stations, fuel depots, chemical plants or where blasting
operations are in progress, or in potentially explosive atmospheres such as fueling
areas, below deck on boats, fuel or chemical transfer or storage facilities, and areas
where the air contains chemicals or particles, such as grain, dust, or metal powders.
Please be aware that sparks in such areas could cause an explosion or fire resulting in
badly injury or even death.
Explosive Atmospheres
When in any area with a potentially explosive atmosphere or where flammable materials
exist, the product should be turned off and user should obey all signs and instructions.
Sparks in such areas could cause an explosion or resulting in bodily injury or even
death. Users are advised not to use the equipment at refueling points such as service or
gas stations. Users are reminded of the need to observe restrictions on the use of radio
equipment in fuel depots, chemical plants or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked.
These include fueling areas, below desk on boats, fuel or chemical transfer or storage
facilities, and areas where the air contains chemicals or particles, such as grain, dust, or
metal powders.
8
Chapter 1
Voice Command Satellite Navigation
1.1 Navigation Device Installation
1. GPS Phone 600: Slide into the GPS Holder.
2. Car Charger: When GPS Phone 600 is low on power, recharge by
connecting one end to the car cigarette lighter/12 volt power outlet and
the other end to the socket on base of the GPS Holder.
3. Car Mount/Holder
™ Attention:
The GPS signal receiver is built into the GPS Phone 600. If car windscreen has
heat reflective metallic film, or the GPS Phone 600 is obstructed by other
objects, reception of the GPS signals may be affected.
9
1.2 GPS Navigation Software Installation
Please refer to the Ostia User Manual for instructions on installing and operating Ostia
Navigation software.
1.3 Conditions for Using GPS Car Navigation
By using this system you are agreeing to the following conditions:
♦ When using this device, please use the included car mounting. Affix device
securely to the car mount. Please note that installation in the areas shown below
can be dangerous.
1.
2.
3.
4.
Do not place where it will obstruct driver vision.
Do not place over air bag.
Do not place where it can not be securely attached.
Do not place in path of activated air bag.
♦ Please set navigation destination before driving. Do not operate the controls on this
system while driving. The responsibility for safe driving rests with you.
♦ GPS positioning is limited by weather and usage location (tall buildings, tunnels,
underpasses, trees, bridges). Most GPS do not work indoors, nor can GPS signals
penetrate buildings, car sun shades and heat reflective film with metallic content.
Please use your GPS where it has a clear view of the sky.
♦ The GPS system is built and operated by the U.S. Department of Defense which is
also responsible for its maintenance and calibration. Any changes made by them
may affect the operation and accuracy of the GPS system.
10
♦ Wireless devices (mobile phones, speed radar detectors) may interfere with the
satellite signal and cause unreliable signal reception.
♦ The GPS position fix is provided for your reference and should not affect actual
driver behavior.
♦ The electronic map data provided in the navigation system is for reference only and
not intended for high precision applications. You should determine your exact
location based on actual road conditions.
♦ When not in use, please do not leave the device inside the car. If exposed directly
to sunlight, the battery may overheat and cause damage to this device. This may
endanger the vehicle as well.
11
Chapter 2
Getting Started
2.1 Package Contents
12
2.2 External Views
1.
2.
3.
4.
5.
6.
7.
Volume control keys
Screen orientation / record hot key
Earphone and microphone jack
Hot key for Ostia
Cell Phone speaker
Today Screen hot key
Left LED
♦ WLAN active LED (Orange)
♦ Bluetooth active LED (Blue,
blinks once)
♦ GPS active LED (Blue,
blinks twice)
8. Right LED
♦ Power charging LED (Red)
♦ Cell phone active LED (Green)
9. Touch screen
10. Left Soft-Key
11. Right Soft-Key
12.
Send button
13.
End button
14. Navigation button.
Press the center of the button
to set as launch key.
15. Micro SD Slot
16. Microphone
17. Mini USB port
18. Stylus holder.
Slide the stylus out of the
holder. This is a two-stage
push-pull stylus.
19. Power button
20. Reset button
21. Camera shutter
22. Built-in camera lens / preview
mirror
23. Hidden antenna for cell phone
24. Speaker
25. Back cover. Battery is inside.
13
Hardware Hot Key Functions
Hardware
Button
1
2
3
4
5
6
7
8
9
10
11
Short Press
(Press once and release)
♦ Adjust volume
♦ Zoom in/out during camera mode
Change screen orientation
Hot key for Ostia
Connect to Today Screen
Connect to Phone/dial/redial/answer
Left Soft-Key:
Soft-keys on the left.
To perform the command / function shown
above the button at the bottom of the screen
display.
Right Soft-Key:
Soft-keys on the right.
To perform the command / function shown
above the button at the bottom of the screen
display.
♦ Hang up during call
♦ Disconnect during GPRS connection
♦ Skip to Today’s screen while in other
programs.
♦ Power Button = open or close screen
♦ Power Button + Reset Button = Cold boot
Reset Button
Camera
14
Long Press
(Press for a few
seconds and
release)
N/A
Voice recording
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Rear Side
Installing the SIM Card
1. Insert the SIM card into the
SIM card slot with its golden
contacts facing down. Refer to
the picture on the right.
Installing the Battery
1. Insert the battery. Refer to the
picture on the right.
2. To keep the battery in place, push
the lock switch up. To take out the
battery, first pull the lock switch
down. Refer to the picture on the
right.
15
2.3 Using the GPS Phone 600 for the First Time
Charging Power and Power Supply
a.
Connect the AC adapter plug to any household power outlet.
b.
Connect the other plug from the AC adapter to the USB port. The
GPS Phone 600 starts to charge automatically.
c.
If you need to connect GPS Phone 600 and a desktop computer,
connect the USB cable to the USB port on the GPS Phone 600
and connect the other end of the USB cable to the USB port on
the desktop computer. Your GPS Phone 600 will also charge at
the same time.
1.
Remove the back cover. (If you are opening this product for the first time, the
main battery and the GPS Phone 600 are packed separately inside the product
package.)
2.
Install the main battery properly and lock the battery securely (install the SIM card
first if you want to use the phone functions).
3.
Connect the AC adapter to any household power outlet and connect the cord from
the AC adapter to the mini-USB port on the GPS Phone 600.
16
4.
Cold Boot: Press and hold the “Power Button” with one hand, and use the stylus
tip to press the “Reset Button” with the other hand. Release the “Power Button”
and the “Reset Button” at the same time. Wait for the GPS Phone 600 to restart
and follow the instructions on the screen to complete screen alignment.
5.
It will take about 8 hours to fully charge the battery the first time. Subsequent
charging will only take about 3 hours. After charging, you can disconnect the AC
Adapter and carry the GPS Phone 600 with you. To maintain reliable operation
charge the power regularly. View the battery icon on the upper right corner to
check the power usage condition.
6.
The LED indicator on the upper left of the GPS Phone 600 displays the WLAN,
Bluetooth and GPS status.
WLAN Active
Bluetooth Active
Orange L E D flashes Blue LED blinks once
every 4 seconds
7.
GPS Active
Blue L E D blinks twice
every 4 seconds
The LED indicator on the upper right of the GPS Phone 600 indicates the
charging status, cell phone status, and notices.
Charging
Fully charged
Insufficient power
Red L E D lights up
Red LED goes off
Green LED lights up
Red LED flashes
Phone is on
Caution or Warning
Green L E D flashes
Orange L E D flashes
17
Re-installation or Replacing the Battery
If the phone, GPRS or wireless LAN connection function is already activated, deactivate
it first and then replace the battery.
1. Slide and remove the back
cover of the GPS Phone 600.
2. Press down to unlock the main
battery lock in order to remove
the battery.
3. Replace the main battery and
lock it properly. When you
remove the main battery, your
GPS Phone 600 will enter sleep
mode.
4. Slide the back cover into the
groove, and reinstall the back
cover.
18
2.4 Power On and Off
Sleep Mode
1. Press the “Power Button” of the GPS Phone 600 to enter the Sleep mode. When
you do so, the screen is turned off and all peripheral devices enter the powersaving mode. If the Phone application is activated it will remain in call waiting
mode (as indicated by the flashing of the green indicator).
2. To turn on the screen later, just press the “Power Button.”
3. Tap
Start, Settings, the System tab, Power and then the Advanced tab to
set the device to turn off automatically after a specified time period.
19
Turn on the Screen
This product is designed with a power-saving feature. If the screen is turned off, press
the “Power Button” of the GPS Phone 600 to turn it on.
If the screen is too dark
and you cannot see
clearly, set the proper
brightness level for the
backlight.
Start, Settings, the
Tap
System tab, Backlight and
then the Backlight Level
tab.
Using the Stylus to Touch the Screen
♦
Your GPS Phone 600 is designed for graphics-based
operation. Use the stylus to perform basic actions such as tap,
drag, and tap and hold on the touch screen. Other actions such
as reset and cold boot will require the use of the stylus tip.
♦
Pull the stylus to full-length to make it easier to tap the screen
during operation. When kept completely in the stylus holder,
the stylus length shortens.
♦
To avoid damage to the screen, avoid pressing too heavily on
the touch screen with the stylus or your fingers.
20
Restarting the GPS Phone 600
If the GPS Phone 600 is unable to maintain normal operation, has no response, or if the
screen is frozen.
Try the following steps in order. If the problem is solved, skip the remaining steps.
Option
Reset
Default
Settings
procedure
Clean Boot
Procedure
Press the “Reset Button” of GPS Phone 600 with the tip of
the stylus.
If the touch screen is functional, please tap
Start,
Programs, Utilities, and then Default Settings.
Hold the “Power Button” and press once on the “Reset
Button” with the tip of the stylus, and release both buttons
simultaneously. Next, continually hold the End Button
until the system inquiry screen is displayed, then
release the End Button. Answer the question(s).
Reset
♦
♦
♦
Reset method: Press the “Reset Button” of GPS Phone 600 with tip of the stylus.
Appropriate situation: If the GPS Phone 600 is unable to maintain normal
operation, has no response, or if the screen is frozen.
Result: In a moment, when GPS Phone 600 automatically completes the system
startup process, the last display will be the Today screen. This will retain all of
your data, settings, and any programs you may have installed.
21
Cold Boot
Cold boot method
Hold the “Power Button” of the GPS Phone 600 with one hand while using the
stylus tip to push in the “Reset Button.” Simultaneously release both the
“Power Button” and “Reset Button”
Appropriate situation
If a previous reset has already been attempted and the GPS Phone 600 is still unable
to maintain normal operations, has no response, or if the screen is frozen.
Before executing the preceding “Cold boot method”, please carefully consider the
following instructions and then decide on the cold boot method.
1. After a cold boot is performed, if no buttons are pressed, the result is identical
to the reset result.
2. If a previous reset has already been attempted but the GPS Phone 600 is still
unable to maintain normal operation, consider the following solution: After
on the bottom right of the GPS Phone
cold boot, hold the End Button
600 until the system inquiry screen is shown, and then release the End
Button. Next, please read thoroughly through the instructions on cold booting
before continuing.
22
Perform cold boot and hold the End Button
. The system will display a two
question inquiry screen. Please carefully refer to following instructions.
♦ Erase all data and load default? (The default is “No.” If Yes or
No was not selected, after a few seconds the system will
automatically execute the default No).
♦ If you press the Left Soft-Key for a few seconds to select
“Yes” then the system will erase all data and load the default
settings. After your GPS Phone 600 restarts, follow the
instructions on the screen to complete.
♦ Delete registry only? (The default is “No.” If Yes or No was
not selected, after a few seconds the system will
automatically execute the default No).
♦ If you press the Left Soft-Key for a few seconds to select
“Yes” then the system will delete the registry only.
Caution
1. After performing a cold boot, the system will retain Microsoft
Windows and pre-installed programs. If you answer “Yes” to the two
questions displayed after a cold boot, other items such as your data,
any programs you have installed, and any custom settings will be lost.
2. There are two ways to retain your data, loaded default and registry:
♦ Perform a Reset.
♦ Performing a Cold Boot, and answer “No” when the above two
questions display.
23
Chapter 3
Using the GPS Phone 600
3.1 Start Screen
Tap
Start, Settings, the System tab, and then Screen.
The first time you use or cold boot the GPS Phone 600, the system will ask you to align
the screen. Continue to tap the center of each cross (+) that appears and follow the
screen instructions to complete the operation. If you feel that the position is not quite
accurate while tapping on the screen, you can align the screen again at any time.
1. Orientation:
♦ Portrait (default)
♦ Landscape (right-handed)
♦ Landscape (left-handed)
2. Tap the Align Screen button to calibrate the
screen. When Align Screen appears, use the
stylus to tap the center of the cross (+) until
the next cross appears, and then follow the
screen instructions to complete the
operation. Finally, tap to exit.
3. Text Size tab:
For selecting the desired text size.
If you are unable to use the stylus, use the following steps to open the touch screen
calibration mode.
1. Simultaneously press the Left Soft-Key on the bottom-left of the GPS Phone
600 and the execution button in the center of the navigation pad.
2. Release these two buttons at the same time, and you will enter the calibration
screen.
24
Today Screen
The Today screen displays important information, such as upcoming appointments and
Start and then Today or by pressing
status indicators. You can access it by tapping
the Today button on the upper-right of your GPS Phone 600.
1.
Start. Tap to switch to a program.
2.
Tap to enable or disable the GPRS
connection feature.
3.
Antenna icon. Tap to turn the phone on or
off.
4.
Speaker icon. For adjusting volume.
5. Time. Tap to display the current date, time, and upcoming appointments.
Tap and hold the time area to select analog or digital clock display from the
list.
6. Today screen. Display important information for the day. Tap on any item to
to sign in to Pocket
enter its relevant setup screen. For example, tap
MSN.
7. The icons mean you can tap to quick link to programs, such as Wireless
Manager, etc.
8. Tap to quick link to Contacts.
25
The following table lists the icons that you may see. Refer to the “Meaning” column for
explanation or tap on the icon to access the instant message.
Icon
Meaning
Speaker is on.
Speaker is off.
Main battery is charging.
Main battery power is low.
Main battery power is very low.
Main battery is fully charged.
Notify you that you have one or more MSN instant messages.
Notify you that you have one or more e-mails, text messages or SMS.
Notify you that you have one or more voice mails.
If there is not enough space on the screen to display all notification icons,
tap this icon to view all icons.
PowerPoint slide show.
Active connection to computer.
Active Sync is synchronizing.
SIM card unavailable.
Phone is powered off.
Signal strength indicator for phone function.
No data sessions active.
GPRS in use.
The G is replaced by an E when the EDGE signal is detected.
GPRS available.
The G is replaced by an E when the EDGE signal is detected.
Wireless LAN Active.
Wireless LAN Data Calling.
Wireless LAN in use.
26
Programs
You can switch from one program to another by selecting it from the
Start menu.
(You can customize which programs you see on this menu. For information, see
“Adjusting Settings” section.) To access some programs, you’ll need to tap
Start,
Programs, and then the program name.
Icon
Programs
Games Group
Description
Bubble Breaker, Solitaire.
Multimedia
Group
Phone Group
Camera, FM Tuner.
Utilities Group
Application Recovery, Bluetooth Manager,
Default Settings, WLAN Utility.
Synchronize information between your GPS Phone 600
and desktop computer.
ActiveSync
SIM Tool Kit, SMS Sender.
Calendar
Keep track of your appointments and create meeting
requests.
Contacts
Keep track of your friends and colleagues.
Notes
Tasks
Create handwritten or typed notes, drawings, and
recordings.
Keep track of your tasks.
Messaging
Send and receive e-mail messages.
Internet
Explorer
Pocket MSN
Browse Web and WAP sites, and download new
programs and files from the Internet.
MSN related programs. For example, send and receive
instant messages with your MSN Messenger contacts.
Create new documents or view and edit Word documents
created on your desktop computer.
Create new workbooks or view and edit Excel workbooks
created on your desktop computer.
View PowerPoint slide shows created on your desktop
computer.
Performs basic calculations.
Word Mobile
Excel Mobile
PowerPoint
Mobile
Calculator
Pictures &
Videos
Take, view, and edit pictures.
27
Icon
Programs
Windows Media
Player
Description
Plays movies or sound files.
File Explorer
Manages files or folders.
Wireless
Manager
Manage the mobile phone, Bluetooth, and wireless LAN
functions.
™ You can also switch to some programs by pressing a program button. Your GPS
Phone 600 has one or more programs buttons located on the front or side of the
unit. The icons on the buttons help to identify the programs they activate. For more
information, refer to “Redefine Hot Keys” section.
28
System Application Programs
♦
Tap
Start, Settings, the Personal tab.
Programs
Buttons
Input
Menus
MSN Options
Owner
Information
Lock
Phone
Sounds &
Notifications
Today
♦
Tap
Description
Set the hot key for GPS Phone 600 hardware button.
Set the details about the input method.
Set the items displaying on the
Start menu
Set the details about Pocket MSN.
Input owner information.
Set the access rights and password of GPS Phone 600.
Set the details about the phone.
Set the volume and notification method.
Set the look of Today screen and display information.
Start, Settings, the System tab.
Program
About
Backlight
Certificates
Clock &
Alarms
Memory
Microphone
Power
Regional
Settings
Remove
Programs
Screen
System
information
Description
Display the important information about the GPS Phone
600.
Set the details about the backlight and brightness.
For network identification to prevent unauthorized access.
Set the time and alarms.
View the memory usage, and the list of running programs,
etc.
Set the microphone volume.
View the power usage condition, whether or not to power off
after a waiting period.
Set the region and information display formats such as date,
time, etc.
Remove programs that are no longer used.
Aligning the screen is helpful in improving the touch
accuracy. You can select the portrait or landscape
orientation.
View the system information.
29
♦
Tap
Start, Setting, the Connections tab.
Program
Beam
Description
Set if receiving end will accept Bluetooth beam data
automatically or not.
Connections Set the network connection.
CSD Type
Set GPS Phone 600 to simulate a modem and access the
Internet through the built-in GSM device.
Network
Set the details about network cards.
Cards
USB to PC
Change the type of USB connection.
30
3.2 Entering Information on Your GPS Phone 600
You have several options for entering new information:
1.
2.
3.
4.
5.
Use the input panel to enter typed text, either by using the soft keyboard or
other input method.
Write directly on the screen.
Draw pictures on the screen.
Speak into your GPS Phone 600 microphone to record a message.
Use Microsoft® ActiveSync® to synchronize or copy information from your
desktop computer to your GPS Phone 600. For more information on
ActiveSync, see ActiveSync Help on your desktop computer.
Entering Text Using the Input Panel
Use the input panel to enter information in any program on your GPS Phone 600. You
can either type using the soft keyboard or write using Letter Recognizer, Block
Recognizer, or Transcriber. In either case, the characters appear as typed text on
the screen.
To show or hide the input panel, tap the Input Panel button. Tap the arrow next to the
Input Panel button to see your choices.
1. Select an input method.
2. Tap to see your choices.
3. Input Panel button.
31
When you use the input panel, your GPS Phone 600 anticipates the word you are
typing or writing and displays it above the input panel. When you tap the displayed
word, it is inserted into your text at the insertion point. The more you use your GPS
Phone 600, the more words it learns to anticipate.
1. Tap here if this is the right word.
™ To change word suggestion options, such as the number of words suggested at
one time, tap
Start, Settings, the Personal tab, Input, and then the Word
Completion tab.
Typing with the Soft Keyboard
1. Tap the arrow next to the Input Panel button and then Keyboard.
2. On the soft keyboard that is displayed, tap the keys with your stylus.
Using Letter Recognizer
With Letter Recognizer you can write letters using the stylus just as you would on paper.
1. Tap the arrow next to the Input Panel button and then Letter Recognizer.
2. Write a letter in the box.
When you write a letter, it is converted to typed text that appears on the screen. For
specific instructions on using Letter Recognizer, with Letter Recognizer open, tap the
question mark next to the writing area.
32
Using Block Recognizer
With Block Recognizer you can input character strokes using the stylus that are similar
to those used on the other PDA’s.
1. Tap the arrow next to the Input Panel button and then Block Recognizer.
2. Write a letter in the box.
When you write a letter, it is converted to typed text that appears on the screen. For
specific instructions on using Block Recognizer, with Block Recognizer open, tap the
question mark next to the writing area.
Using Transcriber
With Transcriber you can write anywhere on the screen using the stylus just as you
would on paper. Unlike Letter Recognizer and Block Recognizer, you can write a
sentence or more of information. Then, pause and let Transcriber change the written
characters to typed characters.
1. Tap the arrow next to the Input Panel button and then Transcriber.
2. Write anywhere on the screen.
For specific instructions on using Transcriber, with Transcriber open, tap the question
mark in the lower right hand corner of the screen.
Selecting Typed Text
If you want to edit or format typed text, you must select it first. Drag the stylus across
the text you want to select. You can cut, copy, and paste text by tapping and holding the
selected words and then tapping an editing command on the pop-up menu, or by
tapping the command on the menu.
33
Writing on the Screen
In any program that accepts writing, such as the Notes program, and in the Notes tab
in Calendar, Contacts, and Tasks, you can use your stylus to write directly on the
screen. Write the way you do on paper. You can edit and format what you’ve written
and convert the information to text at a later time.
Tap Menu and then check Draw to switch to writing mode. This action displays lines on
the screen to help you write.
1. Tap Menu and then check
Draw. Use your stylus like a
pen now.
Some programs that accept writing may not have the Draw function. See the
documentation for the program to find out how to switch to writing mode.
Selecting Writing
If you want to edit or format writing, you must select it first.
1. Tap and hold the stylus next to the text you want to select.
2. Without lifting, drag the stylus across the text you want to select.
If you accidentally write on the screen, tap Menu, then Undo and try again. You can
also select text by tapping Menu and then Draw to deselect it and then dragging the
stylus across the screen.
You can cut, copy, and paste written text in the same way you work with typed text: tap
and hold the selected words and then tap an editing command on the pop-up menu, or
tap the command on the Menu menu.
34
Convert Writing to Text
Tap Menu, Tools, and then Recognize. If you want to convert only certain words,
select them before tapping Recognize on the Tools menu (or tap and hold the selected
words and then tap Recognize on the pop-up menu). If a word is not recognized, it is
left as writing.
1. Select the text you want to convert and tap Recognize on the pop-up
menu.
2. The writing is turned into text.
If the conversion is incorrect, you can select different words from a list of alternates or
return to the original writing. To do so, tap and hold the incorrect word (tap one word at
a time). On the pop-up menu, tap Alternates. A menu with a list of alternate words
appears. Tap the word you want to use, or tap the writing at the top of the menu to
return to the original writing.
1. Tap to return to your original
writing.
2. Or, tap the word you want to
use.
35
Tips for getting good recognition:
1. Write neatly.
2. Write on the lines and draw the descenders below the line. Write the cross of the
“t” and apostrophes below the top line so that they are not confused with the
word above. Write periods and commas above the line.
3. For better recognition, try increasing the zoom level using the Zoom menu.
4. Write the letters of a word closely and leave big gaps between words so that the
GPS Phone 600 can easily tell where words begin and end.
5. Hyphenated words, foreign words that use special characters such as accents,
and some punctuation cannot be converted.
6. If you add writing to a word to change it (such as changing a “3” to an “8” ) after
you attempt to recognize the word, the writing you add will not be included if you
attempt to recognize the writing again.
Drawing on the Screen
You can draw on the screen in the same way that you write on the screen. The
difference between writing and drawing on the screen is how you select items and how
they can be edited. For example, selected drawings can be resized, while writing
cannot.
Creating a Drawing
Cross three ruled lines on your first stroke. A drawing box appears. Subsequent
strokes in or touching the drawing box become part of the drawing. Drawings that
do not cross three ruled lines will be treated as writing
1. The drawing box indicates the
boundaries of the drawing.
2. Tap Menu and then check Draw.
You may want to change the zoom level so that you can more easily work on or
view your drawing. Tap Menu, Zoom and then a zoom level.
36
Selecting a Drawing
If you want to edit or format a drawing, you must select it first. Tap and hold the
stylus on the drawing until selection handle appears. To select multiple drawings,
tapping Menu and then Draw to deselect it and then drag to select the drawings
you want.
You can cut, copy, and paste selected drawings by tapping and holding the
selected drawing and then tapping an editing command on the pop-up menu, or by
tapping the command on the Menu menu. To resize a drawing, make sure the
Draw function is not selected, and drag a selection handle.
Recording a Message
In any program where you can write or draw on the screen, you can also quickly capture
thoughts, reminders, and phone numbers by recording a message. In Calendar, Tasks,
and Contacts, you can include a recording in the Notes tab. Refer to “Voice Recordings
Format” section.
In the Notes program, you can either create a stand-alone recording or include a
recording in a written note. If you want to include the recording in a note, open the note
first. In the Inbox program, you can add a recording to an e-mail message.
37
Creating a Recording
1. Hold your GPS Phone 600’s microphone near your mouth or other source of
sound.
2. Press and hold the Record hardware button on your GPS Phone 600 until you hear
a beep.
3. While holding down the Record button, make your recording.
4. To stop recording, release the Record button. Two beeps will sound. The new
recording appears in the note list or as an embedded icon.
♦ You can also make a recording by tapping the Record button on the
Recording toolbar.
♦ To play a recording, tap it in the list or tap its icon in the note.
1.
2.
3.
4.
Indicates an embedded recording.
Tap to begin recording.
Recording toolbar.
Tap Menu and then check View
Recording Toolbar.
38
Using My Text
When using Messaging or MSN Messenger, use My Text to quickly insert preset or
frequently used messages into the text entry area. To insert a message, tap My Text
and tap a message.
You can add text after inserting a My Text message before sending it. To edit a My
Text message, select Edit My Text Messages. Select the message you wish to edit
and make desired changes.
39
Chapter 4
Using the Phone
The Phone feature on the GPS Phone 600 allows you to perform the following tasks:
1.
2.
3.
4.
5.
6.
Make and receive calls
Quickly make calls or listen to voice mail without entering phone numbers using
Contacts, Speed Dial, or your Call Log.
Check the Call Log to see who has called, whom you have called, add a new
number to Contacts, and access notes taken while you were on a call.
Receive calls and easily take notes during the call.
Send SMS messages.
Customize how your phone rings.
To switch to the Phone function, press the
start and then Phone.
Phone 600 or tap
♦
♦
♦
♦
button on the lower part of the GPS
Caution
To avoid distraction and affecting driving safety, never use your GPS
Phone 600 will driving an automobile or any other moving vehicle.
Make sure that the SIM card is properly installed in your GPS Phone 600
and the Phone is already turned on before you use the functions
described in this section.
When you are on a plane, in a medical facility or at a gas station where
wireless communications devices are not allowed and must be turned
off, please go to Wireless Manager and select the ALL OFF button to
turn off your GPS Phone 600 mobile phone, Bluetooth, and wireless LAN
functions. By pressing the “Power Button” of the GPS Phone 600, you
only turn off the display.
The Phone function relies on the GPS Phone 600 main battery for
power. Maintain the main battery power level to assure call quality and
the normal operation.
40
4.1 Installing and Removing the SIM Card
1. Tap the ALL OFF button in Wireless Manager to turn off your GPS Phone
600’s mobile phone, Bluetooth, and wireless LAN functions
2. Press the “Power Button” of the GPS Phone 600 to turn off the screen.
3. Remove the back cover, unlock the main battery lock and remove the battery.
4. Insert the SIM card into the SIM card slot with the golden contacts facing down.
Use according to the picture labeled on the GPS Phone 600, or remove the SIM
card horizontally.
5. Reinstall the main battery and then lock the main battery lock.
6. Slide the back cover into the groove, and reinstall the back cover.
Installing the SIM Card and Battery
1. Insert the SIM card into the SIM
card slot with its golden contacts
facing down. Follow the picture
indicated on the GPS Phone 600.
2. Main Battery.
3. Back cover.
4. Follow the direction in the
picture to install the main
battery.
5. Main battery lock
41
4.2 Using the Phone
1. Microphone
2. Earphones
Combination
Method
Hold the GPS
Phone manually
for calls.
3. Phone Speaker
4. Phone Microphone (Bottom of GPS Phone 600)
Operation
Hold the GPS
Phone 600 and
position the
speaker close to
your ear and the
microphone close
to your lips.
Install the
Place the
external headset. earphone in your
ear and position
the microphone to
your lips.
Answer or End a Call
Press
Send Button
or
End Button on
the lower part of the
GPS Phone 600.
Use the line control
function. Press the
button on the headset
answer or end the call.
42
Adjust Earphones
Volume
While answering a
call, push the volume
control key on the
side of the GPS
Phone 600 to test
the earphones
volume.
Use the knob on the
headset to adjust the
volume of the
earphones during a
call.
Adjusting the Phone Volume
Tap on the top and adjust all programs’ sound
functions under . Adjust the phone sound volume
under
.
When there is no call, you can push the volume
control key on the side of the GPS Phone 600 or
use the stylus to tap the speaker icon. Tap and
then
to adjust the ring volume of the incoming
call.
Push the volume control key on the side of the GPS
to adjust the
Phone 600 or tap and then
phone volume. You can only do this during a call.
♦
♦
Vibration mode: The speaker icon on the top changes to
Mute mode: The speaker icon on the top changes to
.
.
Adjusting for proper volume:
If earphones are used with the GPS Phone 600 to make calls, set the volume according
to your personal needs.
1. If you are not using earphones, you can set the volume to the top two levels for
hands-free operation.
2. For holding the GPS Phone 600 close to the ear directly for calls, set the volume to
the lower four levels. It is recommended not to use the top two levels because the
volume is high and may affect your hearing.
Turn on / off the speakerphone:
1. Enable the speakerphone: While answering a call, tap Speaker on to turn on.
2. Disable the speakerphone: Tap Speaker off to turn off.
43
4.3 Turning the Phone On / Off and Making Calls
Make certain that the SIM card is properly installed
before attempting to make calls.
1. Turn on the phone: Tap the
icon. When the
message window appears, tap “Turn off flight
mode,” and input the PIN and wait for the phone to
turn on. The
icon changes to .
to enter the phone screen. Use the
2. Dial: Press
stylus to tap the telephone number and then tap the
Enter Button.
3. Answer a call: Press
.
4. End a call: Press
.
icon. When the
5. Turn off the phone: Tap the
message window appears, tap “Turn on flight
mode.”
The following table shows the icons that you may see on the Navigation Bar on the top
of the screen.
Signal
Indicator
Description
SIM card unavailable.
The phone is turned off. To turn it on, tap this icon.
Network is searching or unavailable.
Phone connection unavailable or network error. To turn it off, tap
this icon.
The phone is turned on and signal reception is normal. To turn
off, tap this icon.
Active call. To switch back from other programs, tap this icon.
Call forwarding active.
Calls are forwarded.
Missed call.
Roaming mode.
44
Phone Toolbar
1. Contacts Button: Link to Contacts.
2. Menu Button:
♦ Save to Contacts: Save the dialed phone number
to Contacts.
♦ Create Note: While making a call, you can enter
Notes to use the panel as the memo pad for writing
down notes, pictures or recording.
♦ Options: Change the phone setup such as ring
tone, vibration mode, PIN cod, etc.
3. Keypad Button: Tap to return to the keypad.
4. Speaker on Button: While answering a call, tap to
enable the speakerphone.
Calling from Contacts
Phone numbers entered in Contacts can be used to quickly locate phone numbers and
make calls.
1. In the contact list, tap and hold the contact to
display a pop-menu.
2. Tap Call Mobile or Call Work on the pop-up menu.
3. Tap a contact to display the details.
45
Calling from Speed Dial
On the Phone screen, tap Speed Dial Button to enter the following screen.
1. Tap and hold on a contact. The pop-up menu provides the
Delete and Edit options for phone setup.
2. Tap to redial this number. Remember that this code (for
example, “2”) you want to dial can also be dialed from the
number area in the Phone screen by tapping on “2”.
3. Tap Menu and the New to show the Contacts name and
number will add it to the Speed Dial list. A maximum of 99
numbers are allowed.
Calling from the Call History
Tap Call History Button on the phone screen to enter the following screen.
1.
2.
3.
4.
Tap Menu and then Filter to list the categories. To
search, tap By Caller and follow the screen
instructions to complete the operation.
Tap this icon to redial this number immediately.
Tap and hold the phone number area and tap the
option you need on the pop-up menu. For example,
tap Call to redial this number, tap Save to Contacts
to add this number to the Phonebook.
Tap Menu and then Delete All Calls to delete all call
records. Or tap Call Timers to view the number of
calls, call time and manage call records as shown in
the figure on the left.
46
4.4 Customizing Your Phone
Tap Menu, Options, and then the Phone, Services, Network, or Others tabs to modify
the relevant service setup. Note that the setup values you can change here depend on the
services provided by your telephone company.
♦ Tap the Others tab.
1. GPRS Setting: You can set the
option for GPRS connection.
2. Broadcast Channels: If your telephone
company provides this service, you can
activate it.
3. Band: You can set the band for different
regions.
♦ Tap Menu Options, and then the Phone tab.
1. You can set the ring type as ring, vibration or
mute.
2. If you want to use a customized ring tone file,
use the ActiveSync program, on your desktop
computer to copy the .wav, .mid, or .mp3 ring
tone file to the /Windows/Rings folder on the
GPS Phone 600. You can then select this ring
tone from the Ring tone list.
3. Set the key sound for dialing.
4. You can set a PIN (Personal Identity Number)
to block unauthorized access to your phone.
Your first PIN is provided by your phone
service provider.
47
4.5 Phone Application Programs
Caution
Before you can use the functions described in the Phone Group. Make sure that
the SIM card is properly installed in your GPS Phone 600 and the Phone is
turned on.
SIM Tool Kit
Tap
Start, Programs, Phone, and then SIM Tool Kit.
This screen is for reference only. The actual screen is
based on the service items provided by your telecom
company.
1. Tap any service item.
2. Select Button: Launch service item. Follow the
screen or voice instructions.
SMS Sender
Tap
Tap
Start, Programs, Phone, and the SMS Sender.
Start, Messaging and then New.
Enter the composing SMS screen in Messaging.
1. “Text Messages” means you are editing SMS.
2. Input the mobile phone number.
3. Input the messages you want to send.
4. Tap Menu and then My Text to select canned
messages or to edit your Text Messages.
5. Tap to send SMS message.
48
Chapter 5
Customize Your GPS Phone 600
You can adjust the GPS Phone 600 settings according to your personal preferences
and install other programs.
5.1 Adjusting Settings
To see available options, tap
Start, Settings, then the Personal or System tab
located at the bottom of the screen. The following utilities allow you to adjust the
settings based on your personal work style.
♦ Clock & Alarms
To change the time or to set alarms.
♦ Menus
To customize what appears on the
from the New button.
Start menu, and to enable a pop up menu
♦ Owner Information
To enter your contact information.
♦ Lock
To limit access to your GPS Phone 600.
♦ Power
To maximize battery life.
♦ Today
To customize the look and the information that is displayed on the Today
screen.
49
5.2 Notifications
Your GPS Phone 600 reminds you in a variety of ways when you have something to
do. For example, if you’ve set up an appointment in Calendar, a task with a due date in
Tasks, or an alarm in Clock & Alarms, you’ll be notified in any of the following ways:
♦ A Message box appears on the screen.
♦ A sound, which you can specify, is played.
♦ A light flashes on your GPS Phone 600.
♦ The GPS Phone 600 vibrates.
To choose reminder types and sounds for your GPS Phone 600, tap
Start and
then Settings. In the Personal tab, tap Sounds & Notifications. The options you choose
here apply throughout the GPS Phone 600.
50
5.3 Power Preference Settings
Tap
Start, Settings, the System tab, and then Power.
View the power usage condition or perform the relevant power management settings.
1. Key Lock
With Key Lock checked, when you
accidentally press the hardware buttons
on the GPS Phone 600, the GPS Phone
600 will not exit the sleep mode. This will
prevent unnecessary power
consumption if a button is accidentally
pressed.
2. Battery Icon
Checking this item displays the power
icon on the upper right side of the
screen.
3. Advanced tab
Set the GPS Phone 600 to turn off
automatically after a period of
inactivity.
51
5.4 Backlight
Tap
Start, Settings, the System tab, and then Backlight.
1. Battery Power or External Power tab: Set
the relevant backlight functions.
2. Backlight Level tab: Adjust the backlight
level.
52
5.5 Microphone
Profile
Voice Commander
voice control
Speech recording
Tap
Microphone
Turn the volume down and find the proper
volume setting for better recognition of system.
Turn the volume up.
Start, Settings, the System tab, and then Microphone.
1. Use the slider to adjust volume of the recording
microphone.
2. Default Button: Restore to default system
settings.
53
5.6 Adjusting the Volume
Push the volume control key on the side of the GPS Phone 600 or use the stylus to tap
the
icon on the top of the screen to adjust all program sound functions under
.
Adjust the phone volume under
.
1. Adjust volume: When set to € On, use the stylus
to tap and drag the slider up and down to adjust the
volume. You can also push + or -- on the side of
the GPS Phone 600.
2. Vibrate: Under € Vibrate mode, the sound
function of all programs will be replaced by
icon
vibration, including incoming call rings. The
on the top changes to
.
3. Mute: Under € Off mode, the sound function of all
programs will be turned off, including incoming call
rings. The
icon on the top changes to
.
54
5.7 Finding and Organizing Information
The Search feature on your GPS Phone 600 helps you quickly locate information.
1. Tap
Start, Programs, and then Search.
Input
the text you want to find and then select the
data type. Tap on Search to start the search.
2. To find information that occupies a larger
space, select Larger than 64 KB for Type.
You can also use the File Explorer to search for files and place these files into folders
systematically. Just tap
Start, Programs, and then File Explorer.
1. Tap to change folders.
2. Select the sort order for the list.
3. Tap the folder name to open folder.
4. Tap Menu and then New Folder to
create a new folder.
™ You can move files in File Explorer by tapping and holding the items you want to
move, and then tapping Cut, Copy, or Paste on the pop-up menu.
55
5.8 Navigation Bar and Command Bar
The navigation bar is located at the top of the screen. It displays the active program and
current time, and allows you to switch to programs and close screens.
Use the command bar at the bottom of the screen to perform tasks in programs. The
command bar includes menu names, buttons, and the Input Panel button. To create a
new item in the current program, tap New. To see the name of a button, tap and hold the
stylus on the button. Drag the stylus off the button so that the command is not carried
out.
1. Tap to change volume or mute the GPS
Phone 600.
2. Tap to select a program.
3. Tap to quickly select a program you have
recently used.
4. Tap to see additional programs.
5. Tap to customize the GPS Phone 600.
6. M e n u button.
7. Input panel button.
8. New button
56
5.9 Pop-up Menus
With pop-up menus, you can quickly choose an action for an item. For example, you
can use the pop-up menu in the contact list to quickly delete a contact, make a copy of a
contact, or send an e-mail message to a contact. The actions in the pop-up menus vary
from program to program. To access a pop-up menu, tap and hold the stylus on the item
name that you want to perform the action on. When the menu appears, lift the stylus, and
tap the action you want to perform. Or tap anywhere outside the menu to close the menu
without performing an action.
1. Tap and hold to display the popup menu.
2. Lift the stylus and tap the action
you want.
3. Tap outside the menu to close it
without performing an action.
57
5.10 Redefine Hot Keys
Tap
Start, Settings, the Personal tab, and then Buttons.
These hot keys can be redefined as launch
keys for frequently used programs.
™ End Button
and Send Button
are
exclusive phone functions so they cannot
be redefined.
58
Chapter 6
Using Microsoft ActiveSync
Using Microsoft® ActiveSync®, you can synchronize the information on your desktop
computer with the information on your GPS Phone 600. Synchronization compares the
data on your GPS Phone 600 with your desktop computer and updates both computers
with the most recent information. For example:
♦
Keep Pocket Outlook data up-to- date by synchronizing your GPS Phone 600
with Microsoft Outlook data on your desktop computer.
♦
Synchronize Microsoft Word and Microsoft Excel files between your GPS Phone
600 and desktop computer. Your files are automatically converted to the correct
format.
By default, ActiveSync does not automatically synchronize all types of information. Use
ActiveSync options to turn synchronization on and off for specific information types.
With ActiveSync, you can also:
♦
Back up and restore your GPS Phone 600.
♦
Copy (rather synchronize) files between your device and your desktop computer.
♦
Control when synchronization occurs by selecting a synchronization mode. For
example, you can synchronize continually while connected to your desktop
computer or only when you choose the synchronize command.
♦
Select which information types are synchronized and control how much data is
synchronized. For example, you can choose how many weeks of past
appointments you want synchronized.
59
6.1 Installing and Using ActiveSync
Important Installation Notice
Before you install ActiveSync, make sure that the USB cable on the GPS Phone
600 is not connected to the personal computer. Connect the USB cable only
after ActiveSync is installed.
1. Installing ActiveSync: You could use the Getting Started CD to install Microsoft
ActiveSync version 4.1 or above on the personal computer. ActiveSync is already
installed on your GPS Phone 600.
2. Hardware installation: The USB cable is a plug-and-play device. Use the USB
cable to connect your GPS Phone 600 to your personal computer.
60
3. Using ActiveSync
♦ After installation is complete, the ActiveSync Setup Wizard
helps you customize your synchronization settings.
♦ Once you use the USB cable to connect the two devices properly,
the Set Up a Partnership screen appears on the personal
computer. Set it up according to your requirements. The green
icon
appears on the status bar of your personal computer to
indicate that it is connected.
♦ Click Explore on the Microsoft ActiveSync window on the personal
computer to access files in the GPS Phone 600. You can then use
Windows Explorer to manage the files on your GPS Phone 600.
™ Windows 95 and Windows NT do not support USB connections.
ActiveSync Connection Troubleshooting
Tap
Start, Settings, the Connections tab, and then USB to PC.
1. Factory setting defaults to checking the box.
2. If you have followed the above installation and
operation procedures and find that the connection
between your GPS Phone 600 and desktop PC still
cannot be established, uncheck the box shown on
the left.
61
6.2 USB Synchronization
Before you start to synchronize, use the GPS Phone 600 Getting Started CD to
install ActiveSync on your personal computer. For more information on how to
install ActiveSync, please refer to the ActiveSync CD or online help. ActiveSync is
already installed on your GPS Phone 600.
USB Synchronization
1. After installation is complete, the Setup Wizard will continue to guide you. Adjust
the options according to your actual needs.
2. Use the USB cable to connect the two devices properly and the Set Up a
Partnership screen appears on the personal computer. Set it up according to
your requirements.
1. If this message appears, you
may want to disconnect your
GPS Phone 600 and install
Outlook on your PC before
continuing. In any event,
click OK to close the
message box.
2. Click Next.
3. Check the items you want to
synchronize.
4. Click Next.
62
5. Click Finish.
After installation is complete, the ActiveSync Setup Wizard helps you connect
your GPS Phone 600 to your desktop computer, set up a partnership so you can
synchronize information between your GPS Phone 600 and your desktop
computer, and customize your synchronization settings. Your first synchronization
process will automatically begin when you finish using the wizard.
The green icon appears on the status bar of the personal computer to indicate
that it is connected.
After your first synchronization, take a look at Calendar, Contacts, and Tasks on
your GPS Phone 600. You’ll notice that information you’ve stored in Microsoft Outlook
on your desktop computer has been copied to your device, and you didn’t have to type
a word. Disconnect your GPS Phone 600 from your computer and you’re ready to go!
63
Once you have set up ActiveSync and completed the first synchronization process, you
can initiate synchronization from your GPS Phone 600. To switch to ActiveSync on your
GPS Phone 600, tap
Start and then tap ActiveSync.
For more information on how to use ActiveSync on your personal computer, run
ActiveSync and refer to the ActiveSync online help. To learn more about the GPS Phone
600 ActiveSync, switch to ActiveSync and tap
Start and then Help. Just refer to the
Help for more information.
After the synchronization is complete, tap Calendar, Contacts, and Tasks on the
GPS Phone 600 to view if the information saved in Microsoft Outlook on the
personal computer is already copied to the GPS Phone 600.
On the GPS Phone 600:
Tap
Start, Programs and then
ActiveSync.
1. View synchronization status.
2. View connection status.
3. Tap to connect and synchronize.
4. Tap to synchronize via Bluetooth or
change synchronization settings.
64
6.3 Synchronizing Using Bluetooth
Without using the USB cable to connect the two devices, you can still synchronize using
Bluetooth. The greatest advantage is that you don’t have to plug in and detach from the
USB cable so often. This is especially useful for managing several GPS Phone 600s.
For details on Bluetooth devices, refer to “Using Bluetooth” section.
65
Chapter 7
Connections
7.1 Connecting to the Internet
This section teaches you how to use GPRS wireless network connection. GPRS
wireless networking is a convenient function for working at home or while traveling. You
can use the GPS Phone 600 to browse websites and read or send E-mails, SMS or
MSN messages.
Make sure that your telecom company provides this service and apply for a SIM with
GPRS function. If you already have a SIM card, all you need to do is apply for the
GPRS function from your service provider. Current SIM cards can support GPRS
networking functions.
Generally, you will only need to install the SIM card to your GPS Phone 600 to use the
mobile phone function. The system will automatically add the connection items for this
SIM card. To verify, Tap
Start, Settings, the Connections tab, Connections, and then
“Manage existing connections,” the list will show the newly added network name.
If the system is unable to successfully add the connection to your SIM card, use the
Connection Wizard as shown next.
66
Setting the GPRS / EDGE Connection
Tap
Start, Settings, the Connections tab, Connections, and then the Tasks tab.
1. As shown in the screen on the left tap “Add a new
modem connection.”
2. Enter the “Make New Connection” screen as shown
in the screen on the left.
♦ Input a new connection name for
convenience in making connections in the
future.
♦ Select “Cellular Line (GPRS)”.
♦ Lastly tap Next.
3. Input the Access Point Name provided by your
telecom company (this may appear as APN in the
information provided by your carrier) and tap Next.
4. Input your personal information such as account
number, and tap Finish.
67
Starting the GPRS / EDGE Connection
1. Tap the
or
icon at the top of the
screen and when a message window
appears tap “Turn off flight mode” and input
your PIN to turn on the Phone. The
icon
will change to
while the icon changes
to
.
2. Tap
, then tap Settings to link to
Connections. You are ready to connect
GPRS / EDGE.
3. Select “Message existing connections” in
Connections. Tap and hold on the newly
created connection name, and then select
Connect to finish GPRS / EDGE
connection.
4. Input your account information in the Logon
Network screen and tap to login to the
Network.
5. After the connection is established, the
icon will change to
.
6. Now you can use the appropriate program
to access the Internet, receive or send
E-mails, etc.
68
Disconnecting GPRS / EDGE
1. Disconnect GPRS / EDGE
and the message window
♦ Tap
appear.
♦ Tap Disconnect.
2. Turn off Phone
♦ Tap
and the message window
appear.
♦ Tap “Turn on flight mode.”
69
7.2 Using Bluetooth
Bluetooth is a short-distance wireless communication technology with an effective range
under 10 meters (30 feet). When you enable Bluetooth function, the blue LED blinks
once every 4 seconds.
Bluetooth LED
indicator (Blue)
1. Tap
Wireless
Manager.
2. Tap
to enable
Bluetooth.
Bluetooth Connection Wizard
Tap
Start, Programs, Utilities, and then Bluetooth Manager.
1. Tap on any one of the icons on the left
side of the Wizard screen, the system will
ask you if you would like to activate
Bluetooth. After activation, the LED
indicator on the upper left will flash blue.
2. Tap here and the system will search for all
nearby Bluetooth headsets.
3. Tap to configure your Bluetooth device.
4. Tap to enter the Bluetooth device pairing
screen.
70
All nearby Bluetooth devices found by the
system.
1. Tap on any one the shortcut icons and
you will be able to follow the on-screen
instructions to pair with that particular
device. Devices that have already been
paired with are shown with a 5.
2. Tap on one of the icons which represent
a Bluetooth headset, when a 5 is
shown, it means that you may use that
particular Bluetooth headset.
3. Refresh Search Button: re-scan for all
nearby Bluetooth devices.
4. Change viewing method.
Tap Bluetooth Manger Button in the
Wizard Mode screen to enter this screen.
1. The system will search once again and
add to the number of the devices that
you may pair with.
2. Return to Bluetooth Wizard.
3. Tap to configure your Bluetooth
device.
71
Bluetooth Connection Setting
Tap Settings Button in the Bluetooth Wizard screen to display the Bluetooth Settings
screen.
Tap the General tab.
1. Bluetooth Status
♦ Tap Open to enable Bluetooth function.
♦ Tap Close to disable Bluetooth function.
™ Make sure that you disable Bluetooth function
when you need to save power or if you are in
locations such as an airplane or hospital that
ban the use of wireless devices.
2. Device Identification
♦ Name
Other devices supporting Bluetooth can identify your GPS Phone 600 by
this name.
♦ Address
This is the unique address of your GPS Phone 600.
3. Access
♦ Check “Discoverable”
Within an effective range of 10 meters (30 feet), all devices supporting
Bluetooth can detect your GPS Phone 600 and data transmission is
performed with confirmation from the other party.
♦ Uncheck “Discoverable”
Your GPS Phone 600 can transmit data to other devices but other
devices cannot detect your GPS phone 600.
72
Service
Tap the Service tab.
Provide the settings about
services of serial port, file
transport and exchange vCard
73
Serial Port
If you have other Bluetooth software or hardware that uses a serial port, use the product
as instructed and refer to the accompanied documentation and this section to register
your GPS Phone 600 as a serial port or search for other serial ports.
Tap the Serial Port tab.
1. Tap Add to enter the Settings screen.
™ If you no longer need to use a registered
serial port, tap this serial port under the
“Name” column to highlight and then tap
Delete to delete it.
2. The figure on the left shows the settings screen
for registering a new serial port.
♦ If you select COM for the “Name” field then
the valid options for the “Index” field are 0,
2, 4, 6, and 7.
♦ If you select BTS for the “Name” field, then
the valid options for the “Index” field are 0
to 9.
74
Bluetooth Headset
Tap the Bluetooth Headset tab.
1. Select a headset from the period list.
2. Check “Use Headset.”
FTP Sharing
Tap the FTP tab.
Specify one of the folders on your GPS
Phone 600 as a shared directory.
75
7.3 CSD Type
Tap
Start, Settings, the Connections tab, and then CSD Type.
You must first apply for Circuit-Switched Data (CSD) service from your telecom
company before you can use this function. In short, this function is similar to the modem
dial-up in a personal computer. By simulating the GPS Phone 600 as a modem and
connecting through the built-in GSM device, you can use the GPS Phone 600 to access
the web.
™ This figure is for reference only.
The parameters shown in the screen will be
based on the settings provided by your
telecom company. The charge rate is
regulated by your telecom company.
76
7.4 Connecting with a Personal Computer
For more information, refer to “Microsoft ActiveSync” section.
7.5 Wireless LAN Transmission
Tap the Wireless Manger icon
on the lower right corner of the Today screen. For
more information, refer to “Using Wireless LAN” section.
Wireless LAN LED
indicator (Orange)
Tap
77
Wireless Manager
Chapter 8
Using Wireless LAN
8.1 Connecting to Wireless LAN
This section teaches you how to use the GPS Phone 600’s built-in wireless LAN
function to connect to the Internet. It is convenient for you to browse websites and send
/ receive E-mails through wireless networks at certain locations where wireless
networking services are provided.
When you purchase credits for connecting to the Internet through a wireless LAN, you
may be given some or all of the following information: an IP address, DNS name server
address, Proxy server, port, and network key, etc. You need this information to setup
and activate your connection. In some cases, you may need additional information to
use a company’s wireless connection, please confirm with the network administrator in
your company.
If this is your first time using the wireless LAN function, firstly you should refer to the
following “Configure Your Wireless Network” section for instructions for the necessary
configuration settings. After you have completed the one-time configuration process,
you only need to select the icon
in the Wireless Manager main menu for
subsequent connections.
78
Select the
icon on the bottom right of the Today screen or Tap
and then Wireless Manager.
Start, Programs
1. This icon will show up on your screen whenever your
GPS Phone 600 has detected a usable wireless network
and has connected to that network, indicating that your
GPS Phone 600 has successfully connected to the
network hotspot (Access Point). At this point, the
indicator on the upper left of your GPS Phone 600 will
flash orange.
2. Tap to enter the setup screen.
3. Tap to connect or disconnect to your wireless network, a
means that this function has been disabled.
When the screen shown on the left appears, please choose
a wireless network that you can use, and then tap OK
button. Then, select Work, and tap Connect button.
The first time you use the wireless LAN function, your
system will ask you to set the above mentioned settings,
after that, your system will continue to use the settings from
your most recent successful connection
.
79
8.2 Configure Your Wireless Network
(Reference for a normal network setup)
You will need a correct IP address, DNS name server address, Proxy server, and
connection port number to setup your connection. If you have purchased a wireless
Internet service account, then the service desk at the location where you will be
connecting will provide you with this information, or, you should obtain this information
from the network administrator of your company.
When your GPS Phone 600 is unable to
automatically detect or connect to a usable
wireless network, please try to configure the
network manually. Please refer to this section’s
settings instructions.
1. Select the
icon in the Wireless Manager
main menu, an
navigation bar.
icon will display on the
2. Then Tap
Start, Settings, the
Connections tab, Connections, and then
the Advanced tab, the screen displays shown
on the left.
3. Select the Select Networks Button.
4. As shown on the left, make sure that My Work
Network is selected for both items, and finally
tap
to save and exit.
™ My Work Network is the WLAN connection
method. The next time you need to use the
GPRS connection, you will have to refer to the
above listed steps, select My ISP for the first
item.
80
5. Tap
Start, Programs, Utilities, and then
WLAN Utility or in the Wireless Manager
main menu, select to enter the WLAN
Utility screen.
6. Then select the Configure Button to enter
the WLAN setup screen.
7. Select name of a currently available network
to enter the WLAN authorization setup screen.
8. Set according to the rules and information
provided by the hotspot location.
a.
b.
c.
d.
Authentication: Select Open
Data Encryption: Select WEP to enable
the entry bar about Network key
Network key
Network key index
9. Tap and hold on the name of the network
connection that you can currently use, and then
icon appears on
select Connect. When the
the top of the screen, your wireless network
has been successfully connected.
81
8.3 Configure Your Wireless Network
(Reference for Proxy setup)
To successfully configure your network, you will need the following information: a
correct IP address, DNS name server address, Proxy server, and connection port
number, etc. Please obtain the above listed information from your company’s network
administrator. If your company’s networking environment doesn’t need Proxy server
settings, please close the proxy connection.
Tap
Start, Settings, the Connections tab, Connections, and then the Tasks tab.
If your GPS Phone 600 fails to automatically detect or
connect to a usable wireless network, please try using the
manual method to configure your network settings. Refer
to the settings information in this section.
1. Select “Setup my proxy server” or” Edit my proxy
server,” as shown on the left.
2. In the Proxy Settings tab screen, make sure that the
following items have been checked:
a. This network connects to the Internet
b. This network uses a proxy server to connect to the
Internet
™ The above is applicable to an office environment that requires a Proxy setup.
For networks that do not use a proxy server, skip the following procedures.
3. Enter the name into the “Proxy server” field.
4. Select the Advanced button and enter the advanced settings screen.
82
5. You can modify the settings by tapping the HTTP
type.
6. Enter the number into the “Port” field. Finally, tap
to save and exit.
83
Chapter 9
Sending and Receiving Messages
9.1 E-mails and SMS Messages
Refer to “Connecting to the Internet” section to learn how to connect the GPS Phone
600 to the Internet and start using Messaging to send and receive E-mails and SMS
messages.
This section explains the basics. For additional information, see the online help.
Use Messaging to send and receive E-mails messages in either of these ways:
1. Send and receive e-mail messages by connecting directly to an e-mail server
through an Internet service provider (ISP) or a network.
2. Synchronize e-mail messages with Microsoft Exchange or Microsoft Outlook on
your desktop computer.
™ Inbox synchronization does not support synchronization with Microsoft Outlook
Express.
Reference for using E-mail:
1. Refer to “E-mail Server Setup” section.
2. Refer to “Using E-mails and SMS”.
Reference for using SMS:
1. Refer to “Using E-mails and SMS” section.
2. To send and receive SMS only, you only need to turn on the Phone (antenna icon
on the Navigation Bar is ). It is not necessary to connect GPRS to the network
nor is it necessary to establish a new E-mail account and connection in
Messaging.
84
Synchronizing E-mail Messages
If you want to synchronize e-mails with company or home usage, please refer to this
section. E-mail messages can be synchronized as part of the general synchronization
process. You will need to enable Inbox synchronization in ActiveSync. For information
on enabling Inbox synchronization, see ActiveSync Help on the desktop computer.
During synchronization:
1. Refer to “Connecting to the Internet” section. Select the partnership you want to
establish under “Set up a Partnership” and you can start to synchronize data. If
you choose not to synchronize data, you can manually copy or move E-mails
between the GPS Phone 600 and a personal computer.
2. E-mail messages in the “Outbox” folder on your GPS Phone 600 are transferred
to Exchange or Outlook, and then sent from those programs.
3. Exchange or Outlook E-mail is supported.
4. Messages in the GPS Phone 600 Inbox folder will be transmitted to the personal
computer.
5. If you delete mail in the GPS Phone 600, this mail will also be deleted from the
personal computer the next time the two devices perform synchronization.
6. SMS messages are not synchronized.
85
Connecting Directly to the Mail Server
For single-machine use, not combining office and home E-mails, please refer to “E-mail
Server Setup” section.
You will receive messages directly from the mail server without using a PC. You can
work online or offline. When working online, you read and respond to messages while
connected to the e-mail server. Messages are sent as soon as you tap Send, which
saves space on your GPS Phone 600.
When working offline, once you’ve downloaded new message headers or partial
messages, you can disconnect from the e-mail server and then decide which messages
to download completely. The next time you connect, Inbox downloads the complete
messages you’ve marked for retrieval and sends the messages you’ve composed.
Based on your preference, you can program the GPS Phone 600 to receive mail for the
last few days, receive subjects only or the entire mail, or just receive mail with file
attachments smaller than a specified size. If you want to receive more or less mail, tap
Menu, Tools and then Options to adjust the E-mail account settings according to your
needs.
86
E-mail Server Setup
Refer to this section if you are preparing for single-machine use and not combining
office and home E-mails. If you already have an E-mail account from your ISP or
company network, you can use Messaging to send and receive mails and messages.
To establish a new Messaging E-mail server on your GPS Phone 600, refer to the
following sections.
1. Obtain the following information from your ISP or company’s network administrator
for convenience in setting up the E-mail service.
♦ E-mail address, account name and password.
♦ POP3 or IMAP4 server name for internal mail.
♦ SMTP server name for sending mail.
For AT&T / Cingular, use cwmx.com as the outgoing mail server.
2. E-mail Setup
♦ Tap
Start, Messaging, Menu, Tools, and
then New Account to display the screen on the
left.
♦ Follow the screen instructions to set up the
E-mail service.
3. Refer to “Connecting to the Internet” section to
connect the GPS Phone 600 to the Internet and you
can start sending and receiving E-mails and SMS
messages.
4. Connecting to the E-mail server
♦ Tap Messaging, Menu, Switch Accounts, and
then check POP3.
♦ Tap Menu and then Send / Receive.
™ Tap Menu, Tools and then Options to change the E-mail setup.
87
Using E-mails and SMS
Below is a brief description of the Messaging screen functions:
1. Select the service and folder you want to
display.
2. Select the sort order for messages.
3. Tap to open a message.
4. Tap and hold to display a pop-up menu of
actions.
5. Status bar.
6. Tap to change the account settings.
7. Tap to compose a message.
88
Brief description on writing, sending, reading and replying (to) mail:
1. Send and Receive Mail:
Tap New to compose a message and then tap Send to send it.
2. Tap To, Cc or Bcc to open the Contacts screen. As long as you have set up
Contacts beforehand, you can just tap to select.
3. Tap the data area to input the E-mail address, mobile phone number and subject
directly. If there is more than one contact, use a semi-colon (;) to separate the
addresses.
4. POP3 means to send E-mail, and Text Messages means to send an SMS
message. Note that the same message cannot be sent as E-mail and SMS
message at the same time.
5. Use the scroll bar to view the header.
6. Menu Button: Provides frequently-used functions for writing mail such as request
return receipt, attach files to E-mail, select canned messages, edit canned
messages or cancel mail.
7. Send Button: Send your messages.
89
8. Read and Reply:
Receive new mails by tapping Menu and then Send/Receive. Switch to the “Inbox”
folder and tap to open. The following figure shows the open mail screen.
The menu provides additional functions for
replying to or forwarding message.
9. Change preference settings.
♦ Set the Inbox Synchronization option under ActiveSync.
♦ Tap Messaging, Menu, Tools, Options, and then the Accounts,
Message ... tabs on the GPS Phone 600 to set the appropriate options.
90
Direct Push Technology Alert
The Direct Push Technology alert function will enable you as a corporate user to never
miss another e-mail. Through the ActiveSync feature, your GPS Phone 600 can
instantly and automatically receive important e-mails from Microsoft Exchange Server.
Direct Push Technology Alert Settings
The following description will explain how to setup the ActiveSync program on the GPS
Phone 600 end, and to directly synchronize the GPS Phone 600 with Exchange Server.
This way, your device under GPRS or wireless network connections will be able to
receive in-coming e-mail alerts, and be able to instantly read the messages.
A reminder that if you selected the connection method to be wireless network, for power
saving purposes when the GPS Phone 600 enters sleep mode the connection will be
broken. During this time you will not be able to receive instant e-mail. However, you will
only need to press the “Power Button” to automatically complete the connection to the
wireless network.
Tap
Start, Programs, ActiveSync, Menu, and then
Configure Sever.
1. If the Exchange Server synchronization has not been
setup before, please select Add Server Source.
1) Tap to connect and synchronize.
2) Tap to modify the synchronization settings.
91
2. Obtain the server address, user name, network
etc. from the company network administrator to
successfully setup the server data
3. Tap Menu and then Schedule. The Peak times
and Off-peak times provide an As items arrive
option, this is the direct push technology alert
function.
92
9.2 MSN Messenger
On the Today screen, tap to display the MSN Messenger sign-in screen.
Tap Start, Programs, Pocket MSN, and then MSN Messenger.
To switch to MSN Messenger, tap Start, Programs, and then tap Pocket MSN.
MSN Messenger on your GPS Phone 600 is an instant messaging program that lets
you:
♦ See who is online.
♦ Send and receive instant messages.
♦ Have instant message conversations with groups of contacts.
For more information on using MSN Messenger, tap
Start and then Help.
To use MSN Messenger, you must have a Microsoft Passport™ account or a
Microsoft Exchange e-mail account. You must have a Passport to use MSN
Messenger Service. If you have a Hotmail® or MSN account, you already have a
Passport. Once you have obtained either a Microsoft Passport or a Microsoft Exchange
account, you are ready to set up your account.
™ Sign up for a Microsoft Passport account at http://www.passport.com. Get a free
Microsoft Hotmail e-mail address at http://www.hotmail.com.
93
Setting Up
Before you can connect, you must enter Passport or Exchange account information.
To sign in, enter your e-mail address and password.
™ If you already use MSN Messenger on your desktop computer, your contacts will
show up on your GPS Phone 600 without being added again.
94
Working with Contacts
The MSN Messenger window shows all of your messenger contacts at a glance, divided
into Online and Not Online categories. From this view, while connected, you can chat,
send an e-mail, block the contact from chatting with you, or delete contacts from your
list using the pop-up menu.
1. Tap a contact to start a chat.
2. Tap and hold to display a pop-up menu of
actions
™ To see others online without being seen, tap Menu, My Status, and then select
Appear Offline.
If you block a contact, you will appear offline but will remain on the blocked contact’s
list. To unblock a contact, tap and hold the contact, then tap Unblock on the pop-up
menu.
95
Chatting with Contacts
1. View full chat.
2. Enter message.
3. Tap to send message.
4. View status of the chat. To know if the contact
you are chatting with is responding, look for the
message under the text entry area.
Tap a contact name to open a chat window. Enter your message in the text entry area,
and tap Send. Or tap Menu and then My Text to select a preset message. To invite
another contact to a multi-user chat, tap Menu and then Invite and tap the contact you
want to invite.
To switch back to the main window without closing a chat, tap Menu and then My
Contacts. To revert back to your chat window, tap Menu and then Chats and select the
person whom you were chatting with.
96
Chapter 10
Multimedia
10.1 Using Camera
Tap
Start, Programs, Multimedia, and then Camera.
To take photos of scenery or of other people, turn the GPS Phone 600 so the
screen is facing you and when you are satisfied with the composition, press
the button on the side of the GPS Phone 600.
♦ To take a picture of yourself, turn the GPS Phone 600 around so that the
preview mirror is facing you.
♦ Tap
Start and then Messaging to send the picture as an attachment in an
E-mail.
♦
1.
2.
3.
4.
Shutter
Lens
Preview Mirror
Zoom In / Out
Shooting Tips
To take a self-portrait, it is best to face into the light. For best photo
results, avoid backlit or dark areas.
97
Camera Mode
You can use Camera to shoot pictures and
videos. This section describes the Camera
tools.
1.
2.
3.
4.
Exit Camera.
Camera toolbar.
Viewfinder.
Switch between Camera and Digital video
modes.
5. Open or close the toolbar.
Icon
Meaning
Photo mode: Normal, Timer, Continuous shutter, Portrait.
Activate “Timer” to select the fixed time for shooting a picture.
Activate “Continuous shutter” to select the number of pictures to be
taken.
Choose landscape or portrait.
Enable or disable the flash function.
Display or hide the date.
File format.
Select resolution. The higher the resolution, the larger the picture files.
Select white balance mode.
Select storage path.
Enable or disable Wizard.
Select special effect.
Select picture frame.
Select Frequency.
98
Camera Mode Using Wizard
Tap
or
to select Wizard. After you press the shutter button on the side of the
GPS Phone 600, the Wizard will guide you through how to link to other programs
conveniently. This section explains the Wizard tools.
1. Exit Camera.
2. Photo-viewing area retains the last photo
just taken.
3. Wizard toolbar.
4. If “Continuous Shutter” is selected, it will
directly open or use the last picture just
taken when linking to other programs.
Icon
Meaning
Return to Camera to continue taking pictures.
Delete current picture.
Connect to Messaging.
99
Managing Pictures Shot by Continuous Shutter
to select “Continuous shutter” in the wizard mode. After you press the shutter
Tap
button, you can preview all thumbnails just shot and delete the unnecessary ones.
1. Exit Camera.
2. Tap the thumbnail that you want to
delete.
on the toolbar to delete the
3. Tap
unnecessary picture.
100
Digital Video Mode
recorder
Recording without entering the Camera screen: Directly press and hold the
Button for a few seconds and then release to start recording. To finish recording, press
the Recorder Button to stop.
1. Tap
Start, Programs, Multimedia, and then Camera, DV Mode (the camera
icon in the lower left corner of the screen switches camera modes).
♦ Since only horizontal (landscape) mode is supported, please rotate your GPS
Phone 600 90 degrees when recording.
♦ To shoot a video, turn the GPS Phone 600 so the screen is facing you, press the
Recorder Button on the side of the GPS Phone 600 to start recording. To
finish recording, press the Recorder Button again to stop.
♦ To shoot the footage of yourself, turn the GPS Phone 600 around so that the
preview mirror is facing you.
™ Note: The 3GP format is a compressed version of MPEG 4 used on GSM
camera phones. The 3GP video files can be viewed on a PC using a compatible
player such as Apple’s QuickTime Player or you can obtain a program for your
PC to convert the 3GP files to another format for use with players such as
Windows Media Player.
This section explains the Camera’s digital
video tools.
1.
2.
3.
4.
Exit Camera
Digital Video Mode toolbar
Viewfinder
Switch between Camera and Digital
Video modes
5. Open or close the toolbar
101
Icon
Meaning
Recording quality. The higher the resolution, the larger the file.
Select file format.
Select resolution. The higher the resolution, the larger the file.
Select scene.
Enable or disable sound recording.
Select storage path.
Enable or disable Wizard.
Select special effect.
Select Frequency.
102
Digital Video Mode Using Wizard
or
to select Wizard. After you finish recording, the Wizard will guide you
Tap
through how to link to other programs conveniently. This section explains the Wizard
tools.
1. Exit Camera.
2. The photo viewing window stops at the
first scene of the video you just recorded.
3. Wizard toolbar.
Icon
Meaning
Return to Camera and continue shooting video.
Delete current video.
Connect to Messaging.
Connect to Window Media.
103
Speed Shooting Using the Hardware Hot Keys
♦ Capture Mode
1.
2.
3.
4.
5.
Adjust zoom
Exit Camera
Switch between Camera and Video Recording modes
Open or close the toolbar
Camera Shutter / Video Recorder
♦ Setting Mode / Wizard Mode
1. Use the Navigation Button to navigate up, down, left and right to select from the
icons on the screen.
2. Press the middle button to execute selection.
104
10.2 FM Tuner
Tap
Start, Programs, Multimedia, and then FM Tuner.
This program is for listening to the radio with the headset. The headset will improve
radio quality with its built-in antenna and is necessary to hear the radio.
1. Tool bar:
♦ Screen off: This function turns off the screen
but leaves the program running. Turn on the
power to activate the screen. When the GPS
Phone 600 enters sleep mode, the system
will shut down the program.
♦ My Favorite: Manage My favorite radio
station list.
♦ Band: Change the band frequency. Use the
function to change the local band rate when
traveling overseas.
2. Show the selected band frequency.
3.
Tap and edit the frequency to change the station. The marquee below
shows the relevant information from the radio station.
4.
The volume setting.
5.
Show the My favorite station list. Tap an item from the list to listen to the
station. Hold an item for a few seconds to save the current station.
6.
Turn the sound on or off.
7.
Seek to the first radio station.
Seek to the next radio station.
8.
or
: Set the last or next frequency.
105
Set the station frequency:
1. Tap and edit the frequency to set a custom
station.
Note: The frequency must be in the legal
range.
2. Cancel.
3. OK.
4. Delete the previous digit.
Tap the My Favorite Button in the main screen to
set My favorite station.
1. Close and save the setting.
2. The default value is EUROPE. To change the
setting, hold the desired tab for a few seconds.
3. My favorite station list.
4. Choose an empty item and tap the + button in
the tool bar to edit the station.
5. Tool bar:
Add station
Delete station
Edit station
Set the position in the list
Close without saving
106
Chapter 11
Companion Programs
Microsoft® Pocket Outlook includes Calendar, Contacts, Tasks, Messaging, and
Notes. You can use these programs individually or together. For example, e-mail
addresses stored in Contacts can be used to address e-mail messages in Messaging.
Using ActiveSync, you can synchronize information in Microsoft Outlook or Microsoft
Exchange on your desktop computer with your GPS Phone 600. You can also
synchronize this information directly with a Microsoft Exchange server. Each time you
synchronize, ActiveSync compares the changes you made on your GPS Phone 600 and
desktop computer or server and updates both computers with the latest information. For
information on using ActiveSync, see ActiveSync Help on the desktop computer.
You can switch to any of these programs by tapping them on the
107
Start menu.
11.1 Calendar: Scheduling Appointments and Meetings
Use Calendar to schedule appointments, including meetings and other events. You can
check your appointments in one of several views (Agenda, Day, Week, Month, and
Year) and easily switch views by using the View menu.
1.
2.
3.
4.
Tap to go to today.
Tap to display or edit the appointment details.
View menu.
Tap Menu and then New Appointment to create a
new appointment
™ You can customize the Calendar display, such as changing the first day of the week,
by tapping Menu and then Options.
108
Create an Appointment
1. Tap to return to the calendar (the appointment is
saved automatically).
2. Tap to choose from predefined text.
3. Tap to choose from previously entered locations.
4. Tap to select a time.
5. Tap to select a date.
6. Notes are a good place for maps and directions.
1. If you are in Day or Week view, tap the desired date and time for the appointment.
2. Tap Menu and then New Appointment.
3. Using the input panel, enter a description and a location. Tap first to select the field.
4. If needed, tap the date and time to change them.
5. Enter other desired information. You will need to hide the input panel to see all
available fields.
6. To add notes, tap the Notes tab. You can enter text, draw, or create a recording. For
more information on creating notes, see “Notes: Capturing Thoughts and Ideas”
section.
7. When finished, tap
to return to the calendar.
™ If you select Remind me in an appointment, your GPS Phone 600 will remind you
Start, Settings, the Personal Sounds &
according to the options set in
Notifications.
109
Use the Summary Screen
When you tap an appointment in Calendar, a summary screen is displayed. To change
the appointment, tap Edit.
1. View appointment details.
2. View.
3. Tap to change appointment.
Create Meeting Requests
You can use Calendar to set up meetings with users of Outlook or Pocket Outlook. The
meeting request will be created automatically and sent either when you synchronize
Inbox or when you connect to your e-mail server. Indicate how you want meeting
requests sent by tapping Menu and then Options. If you send and receive e-mail
messages through ActiveSync, select ActiveSync.
Schedule a Meeting
1. Create an appointment.
2. In the appointment details, hide the input panel, and then tap Attendees.
3. From the list of e-mail addresses you’ve entered in Contacts, select the meeting
attendees.
The meeting notice is created automatically and placed in the Outbox folder.
For more information on sending and receiving meeting requests, see Calendar Help
and Messaging Help on the GPS Phone 600.
110
11.2 Contacts: Tracking Friends and Colleagues
Contacts maintains a list of your friends and colleagues so that you can easily find the
information you’re looking for, whether you’re at home or on the road.
1. Tap and enter part of a name to quickly find it in the
list.
2. Tap to display the contact details.
3. This icon indicates that this particular contact entry
is stored on your SIM card, so some of the
information you will only be able to modify when
the mobile phone is turned on.
4. Tap and hold to display a pop-up menu of actions.
5. Provides the relevant menu. For example, select
Options to change the way information is displayed
in the list. Or select Save to SIM or Save to
Contacts to duplicate to Contacts or SIM
phonebook.
6. Tap to create a new contact.
111
Create a Contact
1. Tap New.
2. Using the input panel, enter a name and other contact information. You will need to
scroll down to see all available fields.
3. To assign the contact to a category, scroll to and tap Categories and select a
category from the list. In the contact list, you can display contacts by category.
4. To add notes, tap the Notes tab. You can enter text, draw, or create a recording. For
more information on creating notes, see “Notes: Capturing Thoughts and Ideas”
section.
5. When finished, tap
to return to the contact list.
1. Tap to return to the contact list (the contact is saved
automatically).
2. Tap to select a representative picture for this
contact, when dialing, this picture will appear on
your screen, making it easier to identify the contact
which you are dialing to and adding a lot of fun.
3. Scroll to see more fields.
4. Notes are a good place for maps and directions.
112
Find a Contact
There are four ways to find a contact:
♦ In the contact list, enter a contact name in the box under the navigation bar. To show
all contacts again, clear text from the box or tap the button to the right of the box.
♦
In the contact list, tap Menu, Filter and then select the type of contact that you want
displayed. To show all contacts again, select All Contacts. To view a contact not
assigned to a category, select No Categories.
♦
To view the names of companies your contacts work for, in the contact list, tap
Menu, View By and then Company. The number of contacts that work for that
company will be displayed to the right of the company name.
♦ Tap Start, Programs, and then Search, enter the contact name, select Contacts
for the type, and then tap Search.
Use the Summary Screen
When you tap a contact in the contact list, a summary screen is displayed.
1. View contact details. All of the available contact
information is listed, you can tap and use easily.
2. Tap Menu and then Edit to change the contact
information.
3. Tap to view notes.
113
11.3 Tasks: Keeping a To Do List
Use Tasks to keep track of what you have to do.
1. Indicates high priority.
2. Tap to display or edit the task details.
3. Tap and hold to display a pop-up menu of actions.
4. Tap to create a new task.
5. Provides the relevant menu.
For example, tap Filter to select the category of tasks
you want displayed in the list. Tap Sort By to select the
sort order of the list. Or tap Options to change the way
information is displayed in the list.
114
Create a Task
1. Tap New.
2. Using the input panel, enter a description.
3. You can enter a start date and due date or enter other information by first tapping
the field. If the input panel is open, you will need to hide it to see all available fields.
4. To assign the task to a category, tap Categories and select a category from the list.
In the task list, you can display tasks by category.
5. To add notes, tap the Notes tab. You can enter text, draw, or create a recording. For
more information on creating notes, see “Notes: Capturing Thoughts and Ideas”
section.
to return to the task list.
6. When finished, tap
1. Tap to return to the task list (the task is saved
automatically).
2. Tap to choose from predefined subjects.
3. Notes is a good place for maps and drawings.
To quickly create a task with only a subject, check Show Tasks entry bar on the
Options menu. Then, tap “Tap here to add a new task” and enter your task information.
115
Use the Summary Screen
When you tap a task in the task list, a summary screen is displayed. To change the
task, tap Edit.
1. View task details.
2. Tap to show and hide additional summary
information.
3. View notes.
4. Tap to change task
.
116
11.4 Notes: Capturing Thoughts and Ideas
Quickly capture thoughts, reminders, ideas, drawings, and phone numbers with Notes.
You can create a written note or a recording. You can also include a recording in a note.
If a note is open when you create the recording, it will be included in the note as an
icon. If the note list is displayed, it will be created as a stand-alone recording.
1.
2.
3.
4.
5.
Tap to change the sort order of the list.
Tap to open a note or play a recording.
Tap and hold to display a pop-up menu of actions.
Tap to record.
Provides the relevant menu. For example, check
View Recording Toolbar to show the Recording
toolbar.
6. Tap to create a new item.
Create a Note
1. Tap New.
2. Create your note by writing, drawing, typing, and recording. For more information
about using the input panel, writing and drawing on the screen, and creating
recordings, see “Enter Information on Your GPS Phone 600.”
1. Tap to return to the note list (the note is saved
automatically)
2. Tap to show or hide the input panel.
3. Provides the relevant menu. For example, check
View Recording Toolbar to add a recording to the
note; or check Draw to write on the screen
117
11.5 Word Mobile
Word Mobile works with Microsoft Word on your desktop computer to give you easy
access to copies of your documents. You can create new documents on your GPS
Phone 600, or you can copy documents from your desktop computer to your GPS
Phone 600. Synchronize documents between your desktop computer and your GPS
Phone 600 so that you have the most up-to-date content in both locations.
Use Word Mobile to create documents, such as letters, meeting minutes, and trip
reports. To create a new file, tap Start, Programs, Word Mobile, and then New. A
blank document appears. Or, if you’ve selected a template for new documents in the
Options dialog box, that template appears with appropriate text and formatting already
provided. You can open only one document at a time; when you open a second
document, you’ll be asked to save the first. You can save a document you create or edit
in a variety of formats, including Word (.doc), Word Mobile (.pwi), Rich Text Format
(.rtf), and Plain Text (.txt).
Word Mobile contains a list of the files stored on your GPS Phone 600. Tap a file in the
list to open it. To delete, make copies of, and send files; tap and hold a file in the list.
Then, select the appropriate action on the pop-up menu.
1. Select the type of folder you want displayed in the
list.
2. Tap to change the sort order of the list.
3. Tap to open a document.
4. Tap and hold an item to see a pop-up menu of
actions.
5. Tap to create a new document.
™ You can change the zoom magnification by tapping View and then Zoom. Then
select the percentage you want. Select a higher percentage to enter text and a lower
one to see more of your document.
If you’re opening a Word document created on a desktop computer, check Wrap to
Window on the View menu so that you can see the entire document.
Using the input panel, enter typed text into the document. For more information on
entering typed text, see “Entering Information on Your GPS Phone 600.”
118
To format existing text and to edit text, first select the text. You can select text as you do
in a Word document, using your stylus instead of the mouse to drag through the text
you want to select. You can search a document to find text by tapping Menu, Edit and
then Find / Replace.
1. Tap to return to the document list (changes are
saved automatically).
2. Tap and hold to see a pop-up menu of actions.
3. Tap to format text.
4. Provides the relevant menu. For example, select
Format to change formatting options.
5. Tap View and then check Toolbar to show the
toolbar.
119
11.6 Excel Mobile
Excel Mobile works with Microsoft Excel on your desktop computer to give you easy
access to copies of your workbooks. You can create new workbooks on your GPS
Phone 600, or you can copy workbooks from your desktop computer to your GPS
Phone 600. Synchronize workbooks between your desktop computer and your GPS
Phone 600 so that you have the most up-to-date content in both locations.
Use Excel Mobile to create workbooks, such as expense reports and mileage logs. To
create a new file, tap
Start, Programs, Excel Mobile, and then New. A blank
workbook appears. Or, if you’ve selected a template for new workbooks in the Options
dialog box, that template appears with appropriate text and formatting already provided.
You can open only one workbook at a time; when you open a second workbook, you’ll
be asked to save the first.
Excel Mobile contains a list of the files stored on your GPS Phone 600. Tap a file in the
list to open it. To delete, make copies of, and send files; tap and hold a file in the list.
Then select the appropriate action from the pop-up menu.
120
Excel Mobile provides fundamental spreadsheet tools, such as formulas, functions,
sorting, and filtering. To display the toolbar, tap View and then check Toolbar.
1. Cell contents appear here as you
enter them.
2. Select cell contents for the resource
of chart.
3. Insert Chart button
4. AutoSum button
5. Zoom button
Tap Insert Chart Button to modify the
relevant information, such as titles,
scale, type and series.
121
Tips for Working in Excel Mobile
For more information on using Excel Mobile, tap Start and then Help. Note the
following when working in large worksheets in Excel Mobile:
♦ View in full-screen mode to see as much of your worksheet as possible. Tap View
and then Full Screen. To exit full-screen mode, tap Restore.
♦ Show and hide window elements. Tap View, Show and then tap the elements you
want to show or hide.
♦ Freeze panes on a worksheet. First select the cell where you want to freeze panes.
Tap View and then Freeze Panes. You might want to freeze the top and leftmost
panes in a worksheet to keep row and column labels visible as you scroll through a
sheet.
♦ Split panes to view different areas of a large worksheet. Tap View and then Split.
Then drag the split bar to where you want it. To remove the split, tap View and then
Remove Split.
♦ Show and hide rows and columns. To hide a row or column, select a cell in the row
or column you want to hide. Then tap Menu, Format, then Row or Column, and
then Hide. To show a hidden row or column, tap Menu, Format, then Row or
Column, and then Unhide.
122
11.7 PowerPoint Mobile
View PowerPoint slides created in PowerPoint 97 and above versions on your desktop
computer. The supported formats include .ppt and .pps files. PowerPoint Mobile cannot
be used to create or edit PowerPoint slides.
1. Select the folder you want displayed in the list.
2. Tap to change the sort order of the list.
3. Tap to open a file, and play the slides.
Depending on the slide layout, your screen may
automatically switch to landscape mode to
display the slides.
4. Tap to open the file you played last time.
5. Provides the relevant menu.
Tap
on the lower left corner to open the menu.
Tap End Show to quit.
123
11.8 Windows Media Player
Use Microsoft Windows Media Player to play digital audio and video files that are
stored on your GPS Phone 600 or on a network. To switch to Windows Media Player,
tap Start and then Windows Media.
1. Use full-screen to view video.
2. Display website. Find music or video to be
played from website.
3. Return to the start of the current file or previous
file.
4. Tap to play or pause.
5. Tap to skip to the next song.
6. Tap to adjust volume.
7. Audio / Mute
8. Indicates the progress of the current track.
To enter the screen shown on the left, tap Menu
and then Library.
1. Select Library.
2. Tap and hold the file or folder to be played,
then tap Play or Queue Up.
3. Menu Button: Tap Open File to play files that
do not belong to the current library. Tap
Update Library to update the file list.
Use Microsoft Windows Media Player on your desktop computer to copy digital audio
and video files to your GPS Phone 600. You can play Windows Media and MP3 files
on your GPS Phone 600.
For more information about using Windows Media Player, tap
Help.
124
Start, and then tap
11.9 Internet Explorer
Using Internet Explorer
Use Microsoft® Internet Explorer Mobile to view Web or WAP pages in either of these
ways:
♦ During synchronization with your desktop computer, download your favorite links
and mobile favorites that are stored in the Mobile Favorites subfolder in Internet
Explorer on the desktop computer.
♦ Connect to an Internet service provider (ISP) or network and browse the Web. To
do this, you’ll need to create the connection first, as described in “Connect to the
Internet”.
When connected to an ISP or network, you can also download files and programs from
the Internet or intranet.
To switch to Pocket Internet Explorer, tap
Start and then Internet Explorer.
125
Browse the Internet
Refer to “Connecting to the Internet” section to connect the GPS Phone 600 to the
Internet and start browsing websites.
1. Tap
Start and then Internet Explorer.
2. Input the site address into the address bar at the top of the screen and connect to this
site.
3. Use the scroll bar at the right side or bottom of the screen, or press the up or down
button on the GPS Phone 600 to view the contents of the entire website.
1. Input address here
2. Tap to launch
3. Back Button
4. Provides the relevant menu, such as Favorites, Add
to Favorites, Home, and Refresh.
Aside from keying in the address directly, you can also connect to websites using the
following methods.
♦ Tap the Favorites button, and then tap the favorite you want to view.
♦ In the address bar, tap the arrow ▼ to choose from previously entered
addresses.
To add a favorite link while using the GPS Phone 600, go to the page you want to add,
tap and hold on the page, and tap Add to Favorites.
126
View Mobile Favorites
1. Tap the favorite you want to view.
2. Tap to add or delete a folder or favorite link.
1. Tap the Favorites button to display your list of favorites.
2. Tap the page you want to view.
You’ll see the page that was downloaded the last time you synchronized with your
desktop computer. If the page is not on your GPS Phone 600, the favorite will be
dimmed. You will need to synchronize with your desktop computer again to download
the page to your GPS Phone 600, or connect to the Internet to view the page.
The Mobile Favorites Folder
Only items stored in the Mobile Favorites subfolder in the Favorites folder in Internet
Explorer on your desktop computer will be synchronized with your GPS Phone 600.
This folder was created automatically when you installed ActiveSync.
127
Favorite Links
During synchronization, the list of favorite links in the Mobile Favorites folder on your
desktop computer is synchronized with Pocket Internet Explorer on your GPS Phone
600. Both computers are updated with changes made to either list each time you
synchronize. Unless you mark the favorite link as a mobile favorite, only the link will be
downloaded to your GPS Phone 600, and you will need to connect to your ISP or
network to view the content. For more information on synchronization, see ActiveSync
Help on the desktop computer.
Synchronize Mobile Favorites
If you are using Microsoft Internet Explorer 5.0 or later on your desktop computer, you
can download mobile favorites to your GPS Phone 600. Synchronizing mobile favorites
downloads Web content to your GPS Phone 600 so that you can view pages while you
are disconnected from your ISP and desktop computer.
Use the Internet Explorer plug-in installed with ActiveSync to create mobile favorites
quickly.
Create a Mobile Favorite
1. In Internet Explorer on your desktop computer, click Tools and then Create Mobile
Favorite.
2. To change the link name, enter a new name in the Name box.
3. Optionally, in Update, select a desired update schedule.
4. Click OK. Internet Explorer downloads the latest version of the page to your desktop
computer.
5. Synchronize your GPS Phone 600 and desktop computer. Mobile favorites that are
stored in the Mobile Favorites folder in Internet Explorer are downloaded to your
GPS Phone 600.
™ If you did not specify an update schedule in step 3, you will need to manually
download content to keep the information updated on your desktop computer and
GPS Phone 600. Before synchronizing with your GPS Phone 600, in Internet
Explorer on your desktop computer, click Tools and then Synchronize. You will see
the last time content was downloaded to the desktop computer, and you can
manually download content if needed. You can add a button to the Internet Explorer
toolbar for creating mobile favorites. In Internet Explorer on your desktop computer,
click View, Toolbars, and then Customize.
128
Save GPS Phone 600 Memory
Mobile favorites take up storage memory on your GPS Phone 600. To minimize the
amount of memory used:
♦ In the settings for the Favorites information type in ActiveSync options, turn off
pictures and sounds, or stop some mobile favorites from being downloaded to the
GPS Phone 600. For more information, see ActiveSync Help.
♦ Limit the number of downloaded linked pages. In Internet Explorer on the desktop
computer, right-click the mobile favorite you want to change and then Properties. In
the Download tab, specify 0 or 1 for the number of linked pages you want to
download.
129
Chapter 12
Maintaining the GPS Phone 600
12.1 Adding or Removing Programs
Programs added to your GPS Phone 600 at the factory are stored in ROM (read-only
memory). You cannot remove this software, and you’ll never accidentally lose ROM
contents. All other programs and data files added to your GPS Phone 600 after factory
installation are stored in RAM (random access memory).
You can install any program created for your GPS Phone 600, as long as your GPS
Phone 600 has enough memory. The most popular place to find software for your GPS
Phone 600 is on the Pocket PC Web site
(http://www.microsoft.com/windowsmobile/pocketpc/).
Add Programs Using ActiveSync
You’ll need to install the appropriate software for your GPS Phone 600 on your desktop
computer before installing it on your GPS Phone 600.
1. Programs created for Windows Mobile 5 Pocket PCs are compatible with the GPS
Phone 600, and that many older Pocket PC programs may also run.
2. Read any installation instructions, Read Me files, documentation that comes with the
program. Many programs provide special installation instructions.
3. Connect your GPS Phone 600 and desktop computer.
4. Double-click the *.exe file.
♦ If the file is an installer, the installation wizard will begin. Follow the directions on
the screen. Once the software has been installed on your desktop computer, the
installer will automatically transfer the software to your GPS Phone 600.
♦ If the file is not an installer, you will see an error message stating that the
program is valid but it is designed for a different type of computer. You will need
to move this file to your GPS Phone 600. If you cannot find any installation
instructions for the program in the Read Me file or documentation, use
ActiveSync Explore to copy the program file to the Program Files folder on your
GPS Phone 600. For more information on copying files using ActiveSync, see
ActiveSync Help.
Once installation is complete, tap
switch to it.
Start, Programs, and then the program icon to
130
Add a Program Directly from the Internet
Programs created for Windows Mobile 5 Pocket PCs are compatible with the GPS
Phone 600, and many older Pocket PC programs may also run.
1. Download the program to your GPS Phone 600 straight from the Internet using
Pocket Internet Explorer. You may see a single *.exe or *.zip file, a Setup.exe file, or
several versions of files for different Pocket PC types and processors. Be sure to
select the program designed for Windows Mobile 5.
2. Read any installation instructions, Read Me files, or documentation that comes with
the program. Many programs provide special installation instructions.
3. Tap the file, such as a *.zip or *.exe file. The installation wizard will begin. Follow the
directions on the screen.
Add a Program to the Start Menu
Tap
Start, Settings, the Personal tab, and then Menus.
Check the box for the program you want to add.
If you do not see the program listed, you can either use
File Explorer on the GPS Phone 600 to move the
program to the Start Menu folder, or use ActiveSync on
the desktop computer to create a shortcut to the program
and place the shortcut in the Start Menu folder.
♦ Using File Explorer on the GPS Phone 600: Tap Start, Programs, File Explorer,
and locate the program (tap the folder list, labeled My Documents by default, and
then My Device to see a list of all folders on the GPS Phone 600). Tap and hold the
program and tap Cut on the pop-up menu. Open the Start Menu folder located in
the Windows folder, tap and hold a blank area of the window, and tap Paste on the
pop-up menu. The program will now appear on the Start menu.
♦ Using ActiveSync on the desktop computer: Use the Explorer in ActiveSync to
explore your GPS Phone 600 files and locate the program. Right-click the program,
and then click Create Shortcut. Move the shortcut to the Start Menu folder in the
Windows folder. The shortcut appears on the Start menu. For more information,
see ActiveSync Help.
131
Remove Programs
Tap Start and then Settings.
On the system tab, tap Remove Programs.
Tap a program name from the list under “Programs
in storage memory” to highlight it and then tap
Remove.
If the program does not appear in the list of
installed programs, use File Explorer on your GPS
Phone 600 to locate the program, tap and hold the
program, and then tap Delete on the pop-up menu.
132
12.2 Manage Memory
View Memory Status
Tap
Start, Settings, the System tab, and then Memory.
♦ Tab the Main tab.
1. The status of Storage and Program
memory.
2. Find: Quick link to the Search
program.
♦ Tap the Storage Card tab.
1. Current storage card memory
status.
2. Tap to select the built-in or external
storage card.
133
♦ Tap the Running Programs tab.
1. Tap a program name in “Running Programs
List” and when it is highlighted, tap Activate
or Stop.
2. Activate: Start running the program you selected.
Stop: Stop the program you selected.
Stop All: Stop all programs in the “Running Programs List.”
134
Find Available Memory
Under certain circumstances such as insufficient memory, the GPS Phone 600 cannot
allocate memory automatically. Try to solve this problem through the following methods:
Tap
Start, Programs, and then Search.
1. To find files occupying larger amounts of
Memory, select “Larger than 64 KB” for
type and tap Search.
2. Then, use File Explorer.
3. Tap Start, Programs, and then File Explorer.
Use File Explorer to move the files you want to keep
to external storage cards. Tap and hold the items to
be moved, then tap Cut or Copy on the pop-up
menu. Move to the storage card and then tap Paste.
4. Use File Explorer to delete files that you no longer
need.
135
Tap Start, Messaging, Menu, Tools, Options, and then
Storage tab.
Check “Store attachments on storage card” to save attached
files from E-mails automatically in the storage card in future.
Tap Start, Internet Explorer Menu, Tools, Options and
then Memory.
Tap Clear History and Delete Files to delete records of
websites that you have browsed.
136
Tap Start, Programs, Notes / Word Mobile / Excel Mobile, Menu, and then
Options.
1. Enter the Notes file list screen.
2. Tap Menu and then Options.
3. Tap the “Save to” function button and select SDMMC from the list. This indicates that
you are using your external storage card. Hereafter, new files will be automatically
saved to this storage card.
™ Follow the same operation procedure for Notes in Word Mobile and Excel Mobile.
In addition, you can use the Rename / Move or Save As function provided by the
program above to move or save files to the storage card.
137
12.3 System Information
Tap Start, Settings, the System tab, and then System Information.
Tap + or - to display or hide the system information.
138
Chapter 13
Specifications
Item
Operating system
Processor
Memory
Display
Phone
GPS
Digital camera / camcorder
FM
Interface
Expansion
Battery
Weight
Dimensions
Accessories
Environmental
Description
Windows Mobile 5.0 (AKU 3.0)
Samsung SC3 2442, 400 MHz
128 MB Flash ROM
64 MB SDRAM
2.8" transmissive TFT LCD, touch panel
QVGA 240 x 320,16-bit / 65,536 colors
GSM Quad band 850 / 900 / 1800 / 1900 MHz
EDGE/GPRS Class 10
Bluetooth 2.0 Class 2 + EDR
WiFi IEEE 802.11b/g
Unlocked with one SIM card slot
Up to 5 hours talk time, 160 hours standby
SiRFstarIII 20-channel GPS receiver, WAAS enabled
2.0 mega pixels with flash
Up to 1600 x 1200 resolution
Tri-Band FM radio
Ready for TMC applications
Audio: Microphone, speaker, stereo headset jack
Data: Mini USB
One micro SD card slot
1530 mAh Li-Ion Polymer, rechargeable, replaceable
146 g / 5.2 oz (including battery)
L = 4.45 inch / 113 mm
W = 2.34 inch / 59.5 mm
H = 0.61 inch / 15.5 mm
Getting Started CD, Manuals CD
AC charger, USB cable, stereo earphones, leather case
Car charger*, car mount/holder*, micro SD card*
Operation temperature: -5°C ~ 45°C; 23oF ~ 113oF
Storage temperature: -25°C ~ 50°C; -13oF ~ 122oF
Humidity: 5% - 80% non-condensing
* These items and Ostia navigation software are not included in the 600e package.
139
Appendix
A.1: Regulation Notices and Safety Declaration
Health and Safety Information
Electrical and Battery Safety
♦ Use only the AC adapter provided with this product. Do not use similar items from
other products. The provided AC adapter is for use with this product only. Do not use
it for other electrical products.
♦ Follow the specifications of the battery manufacturer: Avoid charging the battery
when the environmental temperature is higher than 45°C. Do not store or use the
battery when the environmental temperature is higher than 50°C. Otherwise, battery
expansion or leakage may occur.
♦ Do not attempt to disassemble, pound, pierce or damage the battery to avoid
causing injury, danger or risk.
Application Environment Safety
♦ Do not directly expose the GPS Phone 600 to any of the following environments:
rapid changes of temperature, high temperature (such as direct exposure to sunlight
or stoves), extremely low temperature, high pressure, areas with electrostatic
discharge interference or dusty and humid places. Do not soak or wet the GPS
Phone 600 with water or any other liquid.
♦ Do not place the GPS Phone 600 near electrical appliances (such as TVs,
computers, scanners, disc players, faxes, hair dryers, etc.) that may generate
electrostatic discharge interference.
♦ Never drop the GPS Phone 600 nor subject it to strong impact.
♦ Do not use ordinary pen or any object with a sharp tip to tap the GPS Phone 600
cover or screen (LCD panel) to avoid damaging and scratching the surfaces.
♦ Do not use corrosive or volatile liquids to wipe the GPS Phone 600. If necessary,
use a soft cloth or tissue to wipe the GPS Phone 600.
Warranty Security
♦ In case the GPS Phone 600 is damaged, return it to your place of purchase. Do not
attempt to disassemble this device on your own as this may void the warranty.
♦ If any hazards result from the failure of the user to comply with usage rules, we will
not be held responsible for any resulting warranty claims.
Data Security
♦ This company is not responsible for any data loss or damage to the GPS Phone 600
due to improper use. Record important data in your notebook separately or use the
USB accessories that come with this product to save important data to your
computer or storage card.
140
Privacy Restrictions
♦ Some countries require full disclosure of recorded telephone conversations, and
stipulate that you must inform the person with whom you are speaking that the
conversation is being recorded. Always obey the relevant laws and regulations of
your country when using the recording feature of your GPS Phone 600 Phone.
141
A.2: FCC Regulations
♦ This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
♦ This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
o Reorients or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
o Consult the dealer or an experienced radio TV technician for help.
♦ Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
142
A.3: RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This
device is designed and manufactured not to exceed the emission limits for exposure to
radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard for wireless devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests
for SAR are conducted using standard operating positions accepted by the FCC with
the device transmitting at its highest certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the maximum value. This is
because the device is designed to operate at multiple power levels so as to use only the
poser required to reach the network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
The FCC has granted an Equipment Authorization for this device with all reported SAR
levels evaluated as in compliance with the FCC RF exposure guidelines. SAR
information on this device is on file with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: HFS-GPS600.
For body worn operation, this device has been tested and meets the FCC RF exposure
guidelines for use with an accessory that contains no metal and the positions the
handset a minimum of 1.5 cm from the body. Use of other enhancements may not
ensure compliance with FCC RF exposure guidelines. If you do no t use a body-worn
accessory and are not holding the device at the ear, position the handset a minimum of
1.5 cm from your body when the device is switched on.
SAR Information
Read this manual carefully before using.
Warning: Reduced electromagnetic waves, please use properly.
Head: 0.776 W/Kg – PCS 1900
FCC WLAN: 0.136 W/Kg
GSM 850 Body with holster: 0.987 W/Kg
Holster Information
Holster model name: PZX28
Dimensions: 6.1 x 11.8 x 2.5 cm +/- 0.1 cm
143
Where to Find Information
For information on
Programs on your GPS Phone 600
Additional programs that can be installed on
the GPS Phone 600
Connecting to and synchronizing with a
desktop computer
Up-to-date information on your GPS Phone
600
See this source
This User’s Guide and GPS Phone 600 Help. To
Start and then H e l p .
view Help, tap
The GPS Phone 600 Getting Started CD.
Check the user’s guide that comes with this
product or look for the online help relevant to
ActiveSync on the desktop PC or the GPS Phone
600.
http://www.microsoft.com/windowsmobile/
or http://www.pharosgps.com
144
A.4: FAQ
1. What features does the GPS Phone 600 have?
Answer:
1). Built-in 802.11b/g wireless networking module.
2). The built-in camera module’s sensitization and filming quality are better than
other brands of Pocket PCs in the same class.
3). The latest Microsoft Windows Mobile 5.0 operating system, with all its settings
stored on a Flash ROM. You won’t have to worry about losing your data even if
the GPS Phone 600 runs completely out of power. The extra-large Flash memory
space is capable of storing a large amount of personal data and application
programs.
2. How do I configure the wireless network? And how do I connect to the Internet?
Answer:
Wireless Manager will assist you in managing your Bluetooth devices, GSM mobile
devices, and your wireless networks.
1). When you purchase credit points for connection to the Internet via a wireless
connection, you will be given an IP address, DNS name server address, Proxy
server, connection port number, and network key information, you will need this
information to successfully connect to the Internet. Sometimes corporate
networks may need additional information, please contact your company’s
network administrator for details. If you are using your wireless network for the
first time, please refer to the “Configure your Wireless Network” section and set
the necessary configurations.
2). In general, you can activate the wireless connection by tapping the
icon in
Wireless Manager. When your GPS Phone 600 detects and connects to a
available wireless network, a
icon will appear on the top of your screen, this
means that your GPS Phone 600 has successfully connected with a network
hotspot (Access Point). At this time, the indicator on the upper left of your GPS
Phone 600 will flash orange.
3. My GPS Phone 600 cannot boot. What should I do about it?
Answer:
1). Make sure the GPS Phone 600 battery you use still has enough power.
2). Plug your GPS Phone 600 into the charger, and make sure the red charging
indicator lights up. Press the “Power Button.”
3). If you have done the above but your GPS Phone 600 still cannot boot, proceed
with the following step: Remove the GPS Phone 600 back cover, and check the
battery lock is in place. If not, the system cannot be started.
145
4. My GPS Phone 600 has a screen freeze or the system does not respond.
What should I do about it?
Answer:
1). You may reset your GPS Phone 600. This means to re-start the whole system to
release unnecessary resources so that the system can return to normal.
2). If you have reset your GPS Phone 600 but it still cannot operate normally, then
you need to carry out a cold boot to solve this problem. How to carry out a cold
boot: Press and hold the “Power Button” with one hand, and use the stylus tip to
press the “Reset Button” with the other hand. Release the “Power Button” and
the “Reset Button” at the same time. If you answer “Yes” to the two questions
displayed after a cold boot. (Erase all data and load default? Delete registry
only?) The programs installed by yourself, self-made settings, and self-made
data (e.g., “Contacts” and “Calendar”) will disappear and return to their default
settings. As a result, we suggest you copy your data to the storage card. Data
stored in the storage card will not vanish because of a cold boot. Or you can
synchronize the data on your GPS Phone 600 with your desktop computer.
5. Why doesn’t my GPS Phone 600 make any sound?
Answer:
1). Tap the speaker icon
on the top right of the screen, then select the volume
control options, or adjust the volume of the incoming call sound.
2). Alternatively, you may use the volume control key on the side of your GPS
Phone 600 by pushing it up or down to control the volume.
6. Why does my GPS Phone 600 screen automatically become dark?
Answer:
Tap Start, Settings, the System tab, Backlight, and then the Battery Power or
the External Power tab. You may find that if you use battery power, the backlight
automatically shuts down after 30 seconds by default; the external power shuts
down after 1 minute by default. If you think these times are too short, you may
extend them as needed.
7. When I want to open a program or file, a warning message “Not enough memory”
pops up. What should I do about it?
Answer:
Because your GPS Phone 600’s memory is shared by storage memory and program
memory, the following methods are available. You may choose the one that works
best for you.
1). Remove the programs you installed or that are not frequently used to release
program memory space.
2). Delete data that is not used frequently or unnecessary to release storage
memory space.
146
8. The characters on the screen are too small to read. How can I enlarge them?
Answer:
Tap Start, Settings, the System tab, Screen, and then the Text size tab. You
may adjust the text size as you wish. Also, you may select the landscape orientation
in the General tab screen. Try and change them so that you can read more
smoothly.
9. The contact point of my stylus is not quite precise. What should I do about it?
Answer:
Align the screen and the touch screen can respond to the operation of your stylus
more precisely. The following two ways will bring you into the touch screen
calibration mode.
1). Tap Start, Settings, the System tab, Screen, and then Align Screen Button.
2). Simultaneously press the Left Soft-Key on the bottom-left of the GPS Phone 600
and the execution button in the center of the navigation pad.
10. A hardware button on my GPS Phone 600 doesn’t make any response or calls a
wrong program. What should I do about it?
Answer:
Tap Start, Settings, the Personal tab, and then Buttons. Check each button for
correct setup.
11. My GPS Phone 600's ActiveSync cannot be executed or make a connection.
What should I do about it?
Answer:
1). Make sure you have installed ActiveSync version 4.1 or above. The CD
accompanying the product contains the software. If you have lost the CD, you
may download it from the Microsoft Website.
2). Make sure the USB cable supplied with your GPS Phone 600 is connected to
your PC.
3). Make sure you are not executing another program that uses the same serial port
you selected for operation during installation.
4). If your ActiveSync is still not working, remove the ActiveSync software at the PC
end and install it once again.
147
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising