Series 90-70 Programmable Controller Data Sheet Manual, GFK

Series 90-70 Programmable Controller Data Sheet Manual, GFK
1
Discrete Output Modules
IC697MDL341
51
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module (IC697MDL341)
datasheet GFK-0382J
Features
D
D
D
a44139
12 individually isolated points
2 amp capacity per point
A1
A2
A3
A4
A5
A6
A7
A8
High inrush capacity (10x rated current)
Functions
The 120/240 Volt AC 2 Amp Isolated Output Module for use
with a Programmable Logic Controller (PLC) provides 12
isolated output points. This allows each point to be used on
different phases of the AC supply. Each output point is individually fused with a 3.15 amp replaceable fuse.
B1
B2
B3
B4
B5
B6
B7
B8
C1
C2
C3
C4
C5
C6
C7
C8
FUSE
D1
D2
D3
D4
D5
D6
D7
D8
A1
A2
A3
A4
A5
A6
A7
A8
B1
B2
B3
B4
B5
B6
B7
B8
C1
C2
C3
C4
C5
C6
C7
C8
D1
D2
D3
D4
D5
D6
D7
D8
FUSE
OUTPUT
120/240V AC
2A/PT
PILOT DUTY
50/60 HZ
16A MAX/MODULE
1
3
A1
4
5
LED indicators which give the ON - OFF status of each
point on the logic (PLC) side of the circuit as well as an
LED to indicate the status of the fuses are located at the
top of the module. If one or more of the fuses should
blow, this LED will turn ON.
The module is mechanically keyed to ensure correct replacement with a similar module type in the field. I/O
references are user configurable without the use of jumpers or DIP switches on the module.
Configuration is done using the configuration function of the MS-DOSr or Windowse programming
software running on Windowsr 95 or Windows NTr
over Ethernet TCP/IP or through the SNP port. The
Programming Software configuration function is
installed on the programming device. The programming device can be an IBM XT, AT, PS/2 or compatible Personal Computer.
A1
H
~N
~N
A2
6
A2
The module provides a high degree of inrush current
which makes the outputs suitable for a wide range of inductive and incandescent loads. The module will operate
most size 4 contactors.
H
2
7
H
8
9
A3
~N
10
A3
11
H
12
13
B1
14
15
H
~N
~N
B2
16
B2
B1
17
H
18
19
B3
B3
~N
20
21
H
22
23
C1
24
25
H
~N
~N
C2
26
C2
C1
27
H
28
29
C3
C3
~N
30
31
H
32
33
D1
34
35
H
~N
~N
D2
36
D2
D1
37
H
38
39
D3
D3
~N
40
SLOT
MODULE IC697MDL341
LABEL 44A726758–013R02
Although this module is configured as a 16 point output, only outputs 1 through 12 are available to be referenced in your program. For example, if the starting
reference is Q0017, then valid references are Q0017
through Q0028.
r IBM and PS/2 are registered trademarks of International Business Machines Corporation.
r MS-DOS, Windows, Windows 95, and Windows NT are registered trademarks of Microsoft Corporation.
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
51-1
Discrete Output Modules
2
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
Operation - 120/240 Volt AC 2 Amp Isolated Output Module
OPTO
ISOLATOR
BACKPLANE
SYSTEM
INTERFACE
OPEN FUSE
DETECTOR
a44140
ÎÎÎÎ
H
FUSE
3.15A
LED
OPTO
ISOLATOR
OUTPUT
DRIVER
~
N
ÎÎÎ
LOAD
FIELD
CONNECTIONS
MODULE
Figure 1. Block Diagram for IC697MDL341
Output Characteristics
The 120/240 Volt AC 2 Amp Isolated Output Module is
compatible with a wide variety of load devices, such as:
D
D
D
Solenoids
Fusing
Motor starters
Indicators
The rating of 2 amps per point applies to the long-term
current capacity of each point. Because of overall heat
dissipation within the module, the maximum current for
the module is limited to 16 amperes.
Each output on this module is capable of transiently conducting a surge current which is much greater than its longterm current rating. The rate at which such surges can be
repeated depends on the current rating of the device and the
duty cycle (percent of time the device is ON).
For typical incandescent devices operating at a 50% duty
cycle, the following repetition rates apply to this module.
Steady-State Current (mA)
Repitition Rate (Hz)
0.5
5
1
1
2
0.1
Fault Mode Selection
This output module can be configured from the programmer
so that output points assume one of two states in response to
certain operating or default conditions. These states are:
D
D
For more detailed information on module configuration,
refer to the Programming Software User’s Manual for
IC641 software products.
Maintain existing output state
Turn outputs OFF
51-2
Each output is fused with a replaceable 3.15 amp fuse.
Replace with the following type:
D
Metric 5 x 20 mm - 3.15 amp, 250V, Slo-blo
Module Mechanical Keying
This module includes a mechanical key that prevents inadvertent substitution of one module type for another in a
given slot. The key fits a uniquely shaped area on the
board below the connector. Each module has a key packaged with it.
When the module is first installed, the key latches onto the
backplane center rail. When the module is extracted, the
key remains in the center rail, configuring the slot to accept only identical module types.
If it is necessary to change the module location in the rack
after the key has been latched onto the center rail of the
rack, the key can be removed by pushing it upward to unhook the latch while pulling it off the rail. It may then be
reinserted onto the module and the module inserted into
the rack in the desired location.
Note that on;y a power supply can be placed in the leftmost rack position, and slot 1 (adjacent to the power supply) must always contain a CPU (in rack 0 - the CPU
rack), or a Bus Receiver Module (in an expansion rack).
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
Discrete Output Modules
3
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
Field Wiring
The module is wired as shown in Figure 2. Since each
output is isolated from the other outputs, a wire from the
power source to the power input terminal for each output
is required (power input terminals for each output are not
connected inside the module).
The detachable field wiring terminal board will accept
wire sizes from #22 (0.36 mm2) through #14 (2.10
mm2). Two wires may be terminated on a given lug if
both wires are the same size. There is room for a
bundle of forty #14 (2.10 mm2) wires to be routed out
through the terminal board cavity.
The wire bundle can be secured to the terminal board
by passing a cable tie through a cleat located at the
lower corner of the terminal board.
a43985
TERMINALS
FIELD WIRING
1
2
3
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
H
~
N
A1
4
5
6
A2
7
8
9
A3
10
11
12
13
B1
14
15
16
B2
17
18
19
B3
20
21
22
23
C1
24
25
26
C2
27
28
29
C3
30
31
32
33
D1
34
35
36
D2
37
38
39
D3
40
Figure 2. Field Wiring Connections
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
51-3
Discrete Output Modules
4
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
Recommended Field Wiring Procedures
The following procedures are recommended when connecting field wiring to the detachable terminal board on this input
module. Module features referenced in the following procedures which are common to all IC697 I/O modules are illustrated in the following figure.
a43855
JACKSCREW
JACKSCREW
HINGED
DOOR
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
Î ÎÎÎÎ
Î
ÎÎÎÎ
ÎÎ
ÎÎ
Î
Î
TERMINAL
BOARD
CORD
TIE
CORD
TIE
CLEAT
CORD
TIE
CLEAT
CORD
TIE
STRAP
CLEAT
Î
Î
Î
Î
STRAP
STRAP
Figure 3. I/O Module Features
1. Turn off power before removing or installing terminal boards. Open the hinged door on the module to access a jackscrew which holds the terminal
board securely in place. The detachable field wiring terminal board can now be removed from the
module by turning the jackscrew counter-clockwise until it is fully disengaged.
2. To remove the terminal board, grasp the top of the
terminal board and swing it outward as shown in
Figure 4.
Caution
Do not use the hinged door to remove the
terminal board. The hinged door could
be damaged if this is done.
51-4
3. The terminal board is designed to accept wire sizes
from AWG #22 (0.36 mm) through AWG #14 (2.10
mm2). It is important that when using AWG #14
(2.10 mm2) wire for wiring all points, that a maximum insulation diameter of .135 inch (3.43) not be
exceeded. To ensure proper connection, two wires
may be terminated on any one terminal only if
both wires are the same size.
4. The terminal board is designed to accept a maximum of (40) AWG #14 (2.10 mm2) wires. If AWG
#14 (2.10 mm2) wires are to be used, then wire
markers should be placed at least 8 inches (203
mm) from termination end to provide sufficient
space for the hinged door to close.
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
Discrete Output Modules
5
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
Î
Î
ÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎÎÎ
ÎÎ
Î
Î
ÎÎ
Î
ÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Î
Î
Î
ÎÎ
ÎÎ
JACKSCREW
a43747
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎÎ
ÎÎ
ÎÎÎÎ
ÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
DO NOT
PULL
ON DOOR
WIRE BUNDLE CABLE TIE CLEAT
Figure 4. Removal of I/O Terminal Board
5. After completing connections to all modules in a
rack, the wire bundle must be secured. To ensure
that the wire bundle is secured properly, it is recommended that a cable tie be wrapped around the
wire bundle and tightly secured through the cable
tie cleat located at the lower right corner of the
terminal board. For extremely large wire bundles,
additional cable ties should be used.
6. A door label insert is included with each module to
indicate circuit wiring information and provide
space to record user circuit wiring identification.
A slot is provided on the hinged door to allow for
insertion of this label. If the label is difficult to insert, crease the scored edge before insertion. The
outside label has a color coded stripe to allow
quick identification of the module voltage type
(blue: low voltage; red: high voltage).
7. After field wiring is completed, the terminal board
should be securely fastened to the rack by inserting the terminal board strap (attached to each
module) into the small rectangular slots in the bottom card guide grill on the rack. This strap not
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
only secures the terminal board to the rack, it also
provides a way of identifying the wired terminal
board with its correct mating rack slot location.
8. For adequate module ventilation, it is recommended that at least a 6 inch (152mm) clearance be
allowed above and below the rack grill. Wire
bundles should not obstruct the rack grill work.
Removing an I/O Module
The instructions below should be followed when removing an I/O module from its slot in a rack.
D Grasp the board firmly at the top and bottom of
the board cover with your thumbs on the front of
the cover and your fingers on the plastic clips on
the back of the cover.
D Squeeze the rack clips on the back of the cover
with your fingers to disengage the clip from the
rack rail and pull the board firmly to remove it
from the backplane connector.
D
Slide the board along the card guide and remove
it from the rack.
51-5
Discrete Output Modules
6
GFK-0382J
August 1997
120/240 Volt AC, 2 Amp Isolated 12-Point Output Module
Table 1. Specifications for IC697MDL341 [
Rated Voltage:
120/240 volts AC
Outputs per Module:
Isolation:
12 individually isolated
1500 volts - any output to backplane
500 volts between points
Output Voltage Range:
85 to 264 volts AC, 47-63 Hz
Output Current:
2 amps maximum per point
16 amps maximum per module
Output Characteristics
Inrush Current:
20 amps maximum for one cycle (20 ms)
Output Voltage Drop:
1.5 volts maximum
Response Time-On:
1 ms maximum
Response Time-Off:
1/2 cycle maximum
Output Leakage:
3 mA maximum at 120 volts AC
Current Required from 5 V Bus:
6 mA maximum at 240 volts AC
.25 amp
VME
System designed to support the VME standard C.1
[ Refer to GFK-0867B, or later for product standards and general specifications. For installations requiring compliance to more
stringent requirements (for example, FCC or European Union Directives), refer to Installation Requirements for Conformance to
Standards.
Table 2. Ordering Information
Description
Catalog Number
OutputModule, 120/240 VAC, 2 Amp Isolated, 12 Points
IC697MDL341
Note: For Conformal Coat option, or Low Temperature Testing option please consult the
factory for price and availability.
51-6
t
Series 90 -70 Programmable Controller Data Sheet Manual
GFK-0600F
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement