Advertisement
Advertisement
ZN-BT662XE-MIR Installation Guide
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL.
!
!
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ZN-BT662XE-MIR Installation Guide
Table of Contents
APPENDIX (C): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................... 20
01A.01 3
ZN-BT662XE-MIR Installation Guide
1. FEATURES
Camera
Indoor/Outdoor IR Bullet IP Camera
1/2.7” 1080p CMOS
ICR type true day & night
ONVIF Support (End of Aug)
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MJPEG, 25/30FPS@1080p(PAL/NTSC)
Analog video out for external monitors
Video Motion Detection supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
OSD for camera control supported
SDK (Software Development Kit) provided
ZNS
presence (Included as basic)
01A.01 4
ZN-BT662XE-MIR Installation Guide
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera Video out cable
Hex wrench driver Screws
Quick installation Guide DC power adaptor
Terminal block
Screw anchors i
Note
The above contents are subject to change without prior notice.
01A.01 5
IPN6602HD-5215
ZN-BT662XE-MIR Installation Guide
3. PART NAMES
①
④
IPN6602HD-5311 IPN6602HD-5215
⑤
⑥
②
* Models herein and their appearance are subject to change without any prior notice.
Cable arrange
③
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
Red : AIN
White : AOUT
⑦
⑧
⑨
⑩
⑪
TELE
WIDE
FAR
NEAR
VOUT
AF
NT/PAL
F/D
FAR
TELE
NT/PAL
VOUT F/D
NEAR
WIDE
① Sunshield
Position the sunshield to prevent direct sunshine.
② Control panel
Open the control panel to control LEDs, OSD menus, and the extra video output. You can also find the reset button on the control panel. To learn how to reset your device, refer to 6.3.
Reset .
③ Ventilation hole
The ventilation holes help to reduce the temperature difference between inside and outside and prevent water from being condensate.
④ Joint for 3 axis
Use this part to adjust the camera to the desired position. Refer to 4. Installation for more details.
⑤ Panning joint
Use this part for panning adjustment. Refer to 4. Installation for more details.
⑥ Tilting adjustment
01A.01 6
ZN-BT662XE-MIR Installation Guide
Use this part for tilting adjustment. Refer to 4. Installation for more details.
⑦
4 Pin Connector
A: DO,- B: DO+, C: DI+, D: DI-
⑧
Power Adaptor Connector
The camera needs DC 12V for power supply.
⑨
Network Port
Use this RJ45 LAN connector for connecting the camera to network.
⑩
Audio In
Connect to the audio input device such as a mike.
⑪
Audio Out
Connect to the audio output device such as the amplifier speaker.
01A.01 7
ZN-BT662XE-MIR Installation Guide
4. INSTALLATION
1)
Place the installation template that is provided in the package on the desired position of installation.
2)
Drill four holes on the template and insert anchor blocks into the holes.
Fasten the camera with screws.
3)
Make sure the cables are properly connected to the camera.
4)
Adjust the camera to the desired angle by unscrew the joints by referring to the following pictures.
Adjust this joint to install it on the wall
Tiling adjustment Panning adjustment
!
Caution
The camera may fall off the ceiling even after the proper installation and mounting. To prevent any accident, make sure the ceiling is firm and stable enough to support the camera. If any reinforcement is needed, consult with your safety personnel and proceed with the installation.
01A.01 8
IPN6602HD-5311
ZN-BT662XE-MIR Installation Guide
4.1. Installation Template
01A.01
(Unit: mm)
Cable arrange
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
9
Red : AIN
White : AOUT
IPN6602HD-5311 IPN6602HD-5215
ZN-BT662XE-MIR Installation Guide
4.2. Adjusting LED options and lens focus
Adjust the zoom and focus of the lens with the lever of ① and ② on the following picture.
TELE FAR AF
WIDE NEAR NT/PAL
RESET
VOUT
TELE/WIDE : Uses for zoom
FAR/NEAR : Uses for focus
AF : Auto focus
NT/PAL : NTSC, PAL button
Vout : Uses only for installation
4.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Camera . Brightness, contrast, saturation and sharpness can be adjusted.
IPN6602HD-5311 IPN6602HD-5215
TELE
WIDE
FAR
NEAR
VOUT
AF
NT/PAL
F/D
FAR
TELE
NT/PAL
VOUT F/D
NEAR
WIDE
FAR
TELE
NT/PAL
VOUT RESET
NEAR
WIDE
01A.01 10
IPN6602HD-5215
ZN-BT662XE-MIR Installation Guide
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
DI/DO
Power DC 12V
LAN Port
Red : AIN
White : AOUT
Audio In
Audio Out
DI/DO Connection
A: DO-, B: DO+ , C: DI+ , D: DI-
Sensor (DI) connection
The camera provides 1 channel D/I. It can be connected to either a voltage type sensor or a relay type sensor as the following figures. It can be selected by software.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Input voltage threshold: 1.5V
!
Caution
Do not exceed the maximum input voltage or relay rate.
01A.01 11
ZN-BT662XE-MIR Installation Guide
Internal +3.3V
DI
Output of
Sensor
+ -
Internal
DI
Output of
-
COM - + COM
Relay Type
Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
!
Caution
Do not exceed the maximum relay rating.
Internal
DO
Device
Voltage Type
COM
Relay Type
Power Connection
A 12 DC power connector is required for this device.
Network Connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Connect a LAN cable.
Audio Input/Output Connection
Connect the audio input device such as a mike to the audio input port and the audio output device such as the amplifier speaker to the audio output port.
Audio Input : Linein, 1.43Vp-p(M in 1.35Vp-p, max 1.49 Vp-p), 39 KΩ
Audio Output : Lineout, 46mW Power, 16 Ω
01A.01 12
ZN-BT662XE-MIR Installation Guide
!
Caution
Do not connect the speaker without amplifier.
01A.01 13
ZN-BT662XE-MIR Installation Guide
6. CONFIGURATION
6.1.Set up network environment
The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the MAC address of your device. Please make sure the device and your PC are on the same network segment before running the installation. If the network segment between your PC and the device is different, change your PC’s settings as below.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.2. View video on web page
View the live video on a web page using your IP device and its IP address. You can use the
IPAdminTool or enter the IP address on the web page.
6.2.1. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras and shows the product name, IP address, MAC address and etc. IPAdminTool is provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
01A.01 14
ZN-BT662XE-MIR Installation Guide
To use the IPAdminTool and view the live video on a web page:
1.
Start IPAdminTool. Names and info of currently activated devices appear as a list.
2.
Right-click on the desired device and select Web view .
3.
Click pop-up blocked and install the ActiveX setup.exe by clicking the Run or Save button. You need to install the ActiveX for displaying the images. i
4.
Follow the instructions of the dialog boxes and complete the installation. Then the live video is displayed on the main page of the web browser.
5.
If the live video is not displayed with the message said, “ This software requires the
Microsoft XML Parser V6 or higher. Please download MSXML6 from the Microsoft website to continue. Error code: Can not create XMLDOMDocument.
”, please download and install the relevant MSXML.
Note
If the ActiveX setup.exe
file fails to be installed successfully, close all of the
Internet Explorer windows and go to Program Files > AxInstall folder on your computer. Then, run Uninstall.exe
and try to perform the steps 1 to 4 above again.
01A.01 15
ZN-BT662XE-MIR Installation Guide
6.2.2. View video using IP address
View the live video on a web page using your IP device and its IP address. To have the correct
IP address ready and use it on a web page:
1.
Convert a MAC address to an IP address or check the IP address on the IPAdminTool. Refer to
Appendix (D): Hexadecimal-Decimal Conversion Table .
(The MAC address is attached on the side or bottom of the device.)
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the Hexadecimal number to Decimal number.
2.
Open a web browser and enter the IP address of the device.
3.
Click pop-up blocked and install the ActiveX setup.exe by clicking the Run or Save button.
You need to install the ActiveX for displaying the images.
4.
Follow the instructions of the dialog boxes and complete the installation. Then the live video is displayed on the main page of the web browser.
6.3. Reset
1.
While the device is in use, press the Reset button.
2.
Wait for the system to reboot.
6.4. Factory Default
1.
Press reset button and hold.
2.
Release the Reset button after 5 seconds until LED blinks.
3.
Wait for the system to reboot.
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway:
User ID:
Password:
192.168.0.1 root pass
01A.01 16
ZN-BT662XE-MIR Installation Guide
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
Image Sensor
Effective Pixels
TV System
Horizontal Resolution
Zoom
White Balance
Scanning System
Sync System
Min. Illumination
Lens
Focus
Iris
Day & Night
Shutter Speed
S / N Ratio
AGC
BLC
DNR
Video
Compression
Number of Streams
Resolution
Compression FPS
De-interlacing
Motion Detection
Burnt-in Text(digital)
Analog Video Output
Audio
Input / Output
Compression
Function
IR Range
Network
OV2715 CMOS
768 x 494 (NTSC) /752 x 582 (PAL)
NTSC / PAL
TBD
X16 Digital Zoom
ATW / AWC / Manual / Outdoor / Indoor
2:1 Interlace
Internal
TBD
3.0 – 9.0mm Vari-Focal F1.2 Motorized Focus & Zoom
Motorized
Auto
COLOR / B/W / AUTO
1/60s ~ 1/120,000s
52 dB (AGC off)
Low / High / Off (Selectable)
BLC / HLC / Off
On/Off (1~32 Level Adjustable)
H.264, MPEG-4, MJPEG Selectable per Stream
Dual stream, Configurable
1920x1080, 1280x720, 800x450, 480x270, 320x180
25/30 fps @ D1 (PAL/NTSC)
Supported (DSP)
Supported
Supported (DSP)
PAL/NTSC (Auto off)
1/1
PCM, G.711
Internal Use: 30M
External Use: 20M
10/100 Base-T
01A.01 17
ZN-BT662XE-MIR Installation Guide
Power over Ethernet
DI / DO
RS-232C/RS-485
Protocol
Local Storage
802.3af (Normal)
1 / 1 ch
Not available
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP,
SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,
FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH, SNMP v2/v3
Not available
Electrical Characteristics
Poser source
Power consumption
Analog Video Output
Audio Input
Audio Output
Sensor(D/I)
Alarm(D/O)
DC 12V
1200mA (Heater ON)
1 Vp-p, 75Ω, Composite
Linein, 1.43Vp-p(Min 1.35Vp-p, max 1.49 Vp-p), 39 KΩ
Lineout, 46mW Power, 16 Ω
Max 50mA@5VDC, TTL level 4.5V threshold
Max 500mA@24VAC or 1A@12VDC
On-state resistance: 50 Ω (max continuous)
Environment Condition
Operating Temperature
Operating Humidity
Operating Range
DC12V : -40˚C ~ 50˚C (-40˚F ~ 122˚F)
PoE : 0 ˚C ~ 50 ˚C (32˚F ~ 122˚F)
Cold Start
DC12V : -20˚C (-4˚F)
PoE: 0 ˚C (32˚F)
Up to 85% RH
Environment Condition
Dimensions
Color
Weight
83mm x 82mm x 194mm (Without bracket)
Ivory
Net: 1.5Kg
01A.01 18
IPN6602HD-5311
ZN-BT662XE-MIR Installation Guide
APPENDIX (B): DIMENSIONS
(Unit: mm)
Cable arrange
DCBA
A : DO-
B : DO+
C : DI+
D : DI-
Red : AIN
White : AOUT
01A.01 19
ZN-BT662XE-MIR Installation Guide
APPENDIX (C): HEXADECIMAL-DECIMAL
CONVERSION TABLE
Refer to the following table when you convert the MAC address of your device to IP address.
Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec Hex Dec
00 0
01 1
02 2
03 3
04 4
05 5
06 6
07 7
08 8
09 9
0A 10
0B 11
0C 12
0D 13
0E 14
0F 15
10 16
11 17
12 18
13 19
14 20
15 21
16 22
17 23
18 24
19 25
1A 26
1B 27
1C 28
1D 29
1E 30
1F 31
20 32
21 33
22 34
23 35
24 36
25 37
26 38
27 39
28 40
29 41
2A 42
2B 43
2C 44
2D 45
2E 46
2F 47
30 48
31 49
32 50
33 51
34 52
35 53
36 54
37 55
38 56
39 57
3A 58
3B 59
3C 60
3D 61
3E 62
3F 63
40 64
41 65
42 66
43 67
44 68
45 69
46 70
47 71
48 72
49 73
4A 74
4B 75
4C 76
4D 77
4E 78
4F 79
50 80
51 81
52 82
53 83
54 84
55 85
56 86
57 87
58 88
59 89
5A 90
5B 91
5C 92
5D 93
5E 94
5F 95
60 96
61 97
62 98
63 99
64 100
65 101
66 102
67 103
68 104
69 105
6A 106
6B 107
6C 108
6D 109
6E 110
6F 111
70 112
71 113
72 114
73 115
74 116
75 117
76 118
77 119
78 120
79 121
7A 122
7B 123
7C 124
7D 125
7E 126
7F 127
80 128
81 129
82 130
83 131
84 132
85 133
86 134
87 135
88 136
89 137
8A 138
8B 139
8C 140
8D 141
8E 142
8F 143
90 144
91 145
92 146
93 147
94 148
95 149
96 150
97 151
98 152
99 153
9A 154
9B 155
9C 156
9D 157
9E 158
9F 159
A0 160
A1 161
A2 162
A3 163
A4 164
A5 165
A6 166
A7 167
A8 168
A9 169
AA 170
AB 171
AC 172
AD 173
AE 174
AF 175
B0 176
B1 177
B2 178
B3 179
B4 180
B5 181
B6 182
B7 183
B8 184
B9 185
BA 186
BB 187
BC 188
BD 189
BE 190
BF 191
C0 192
C1 193
C2 194
C3 195
C4 196
C5 197
C6 198
C7 199
C8 200
C9 201
CA 202
CB 203
CC 204
CD 205
CE 206
CF 207
D0 208
D1 209
D2 210
D3 211
D4 212
D5 213
D6 214
D7 215
D8 216
D9 217
DA 218
DB 219
DC 220
DD 221
DE 222
DF 223
E0 224
E1 225
E2 226
E3 227
E4 228
E5 229
E6 230
E7 231
E8 232
E9 233
EA 234
EB 235
EC 236
ED 237
EE 238
EF 239
F0 240
F1 241
F2 242
F3 243
F4 244
F5 245
F6 246
F7 247
F8 248
F9 249
FA 250
FB 251
FC 252
FD 253
FE 254
FF 255
01A.01 20
ZN-BT662XE-MIR Installation Guide
REVISION HISTORY
MAN# DATE(M/D/Y)
D1A.01
01A.01
04/20/2012
05/02/2012
Preliminary version
Comments
Power consumption revise
01A.01 21
Advertisement