Ganz ZN-NH11VNE User Guide

 

  

 

ZN-Y11VP(N)E/ZN-NH11VP(N)E/ZN-NHW11VP(N)E

 

Quick User Guide

 

 

  

 

 

This   manual   has   been   designed   to   guide   you   through   basic   settings   of   your   IP   devices,   such   as   installation   and   configuration   for   using   them.

 

 

Step1. Connect cables to IP device

Connect   each   cable   to   the   device.

  To   see   the   correct   positions   of   all   connectors,   refer   to   the   following   image   below.

 

*   Models   herein   and   their   appearance   are   subject   to   change   without   any   prior   notice.

 

LOOP OUT  

 

RS-485   DO   DI

RESET

AUDIO

 

RESET   Button  

  + C 1

 

C

 

1 Out In

Micro SD

+

RED  

+ ‐

‐

ETHERNET

LAN  

DC   12V   

CCW  

Set   Screw  

(For   IRIS   LENS)  

!

Caution

Power   Adaptor   Connector   (DC   12V)  

 

Make   sure   the   polarity   is   correct.

  Incorrect   connection   may   cause   malfunction   or   damage   to   the   IP   device.

 

 

 

Step2. Set up network environment

The   default   IP   address   of   your   IP   device   is   192.168.XXX.XXX.

  You   can   find   the   available   IP   address   from   the  

MAC   address   of   your   device.

  Please   make   sure   the   device   and   your   PC   are   on   the   same   network   segment   before   running   the   installation.

  If   the   network   segment   was   different   between   your   PC   and   the   device,   change   your   PC’s   settings   as   below.

 

 

IP   address       :    192.168.xxx.xxx

 

Subnet   mask:    255.255.0.0

 

EC11   Ver1.2

 

1  

 

 

EC11   Ver1.2

 

2  

 

STEP3. View video on web page

View   the   live   video   on   a   web   page   using   your   IP   device   and   its   IP   address.

  To   have   the   correct   IP   address   ready   and   use   it   on   a   web   page:    

1.

Convert   a   MAC   address   to   an   IP   address.

 

(The   MAC   address   is   attached   on   the   side   or   bottom   of   the   device.)  

 

MAC   address   =   00 ‐ 1 C ‐ B8 ‐ C0 ‐ 14 ‐ B1 →  IP   address   =   192.168.20.177

the   Hexadecimal   number   to   Decimal   number.

 

2.

Open   a   web   browser   and   enter   the   IP   address   of   the   device.

 

3.

Click   Continue   to   this   website   (not   recommended)   as   below.

 

(The   explanation   and   captured   images   at   this   manual   are   mainly   on   the   basis   of   Internet   Explorer   7.0)  

 

 

 

4.

Click   pop ‐ up   blocked   and   install   the   ActiveX   control   as   below.

  You   need   to   install   the   ActiveX   for   displaying   the   images.

 

 

 

 

EC11   Ver1.2

 

3  

 

 

5.

Wait   for   a   few   seconds   while   the   web   page   loads.

  The   live   video   is   displayed   as   below.

 

 

6.

If   the   live   video   is   not   displayed   and   “ Can   not   Create   XMLDOMDocument   Install   MSXML4.0

”   message   is   shown   as   below,   please   download   and   Install   from   the   link   below.

  http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B ‐ B4F2 ‐ 46DA ‐ B4B6 ‐

C5D7485F2B42&displaylang=en  

(VCA   Library   requires   MS   XML   4.0

  library   which   is   an   xml   parser   made   by   Microsoft.)  

 

 

 

EC11   Ver1.2

 

4  

 

 

 

Step4. Setting IP Address

 

 

To   set   up   the   Network   configuration:    

1.

Click   Setup   on   the   upper   right   of   the   web   page.

  The   login   page   is   displayed   as   below.

 

2.

Enter   the   default   user   name   (root)   and   the   default   password   (pass),   and   then   select   OK .

 

The   default   username   and   password   are:   root   and   pass .

 

 

3.

Click   System   Options ,   and   then   select   TCP/IP   from   the   drop ‐ down   menu.

 

 

 

To   change   the   IP   address,   please   make   sure   to   check   and   have   the   correct   Subnet   mask   and   Gateway   ready.

  To  

  use   DHCP,   select   Obtain   an   IP   address   via   DHCP .

  

To   learn   how   to   set   up   the   web   page   for   advanced   configuration,   refer   to   the   Web   Page   User's   Manual,   which   is   available   on   the   SDK   at   the   following   path.

  

{SDK root}\DOC\

EC11   Ver1.2

 

5  

 

Advanced setup (ZNS-GIT IPAdminTool)

ZNS ‐ GIT   IPAdminTool   is   a   utility   program   for   IP   products.

  Following   list   shows   a   part   of   features   that   ZNS ‐ GIT  

IPAdminTool   provides.

  z Configure   IP   address,   Subnet   mask   and   Gateway   z Shows   network   related   information   such   as   MAC   address   z Updates   firmware    z Reboots   the   device  

ZNS ‐ GIT   IPAdminTool   is   provided   with   SDK   at   the   following   SDK   path.

 

{SDK root}\BIN\TOOLS\AdminTool\

Rebooting

Reset   can   be   carried   out   as   follows:  

1.

While   the   device   is   in   use,   press   and   hold   the   Reset.

  

2.

Release   the   Reset   button   after   3   seconds.

  

3.

Wait   for   the   system   to   reboot.

 

 

 

Resetting to the Factory Default Settings

This   will   reset   all   parameters,   including   the   IP   address,   to   the   Factory   Default   initialization.

  

To   perform   the   Factory   Default   settings:  

1.

Disconnect   the   power   supply   from   the   device.

  

2.

Connect   the   power   to   the   device   with   the   Reset   button   pressed   and   held.

  

3.

Release   the   Reset   button   after   5   seconds.

 

4.

Wait   for   the   system   to   reboot.

 

 

 

More Information

To   learn   more   about   using   other   features   of   your   devices,   refer   to   the   manual,   which   is   available   on   the   SDK   at   the   following   path.

  

 

{SDK root}\DOC\

EC11   Ver1.2

 

6