Zebex Z-3050BT Linear Image Wireless Handheld Scanner Quick Guide

Add to My manuals
2 Pages

advertisement

Zebex Z-3050BT Linear Image Wireless Handheld Scanner Quick Guide | Manualzz
Radio Notice
This equipment generates uses and can radiate radio frequency energy. If not installed and used in
accordance with the instructions in this manual, it may cause interference to radio communications.
The equipment has been tested and found to comply with the limits for a Class A computing device
pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC rules. These specifications are
designed to provide reasonable protection against interference when operated in a commercial
environment.
Radio and Television Interference
Operation of this equipment in a residential area can cause interference to radio or television
reception. This can be determined by turning the equipment off and on. The user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna.
Relocate the device with respect to the receiver.
Move the device away from the receiver.
Plug the device into a different outlet so that the device and the receiver are on different branch
circuits.
If necessary the user may consult the manufacturer, and authorized dealer, or experienced
radio/television technician for additional suggestions. The user may find the following booklet
prepared by the Federal Communications Commission helpful: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402 U.S.A., Stock No. 004000003454.
For CE-countries
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power
supply unit should be used in order to maintain CE conformance.
Laser Safety
The laser scanner complies with safety standard IEC 60825 -1for a Class I laser produce. It also
complies with CDRH as applicable to a Class IIa laser product. Avoid long term staring into direct
laser light.
Radiant Energy: The laser scanner uses one low-power visible laser diodes operating at 650nm in
an opto-mechanical scanner resulting in less than 3.9µW radiated power as observed through a
7mm aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unprotected laser light with a
peak output up to 0.8mW would be accessible inside.
Laser Light Viewing: The scan window is the only aperture through which laser light may be
observed from this product. A failure of the scanner motor, while the laser diode continues to emit a
laser beam, may cause emission levels to exceed those for safe operation. The scanner has
safeguards to prevent this occurrence. If, however, a stationary laser beam is emitted, the failing
scanner should be disconnected from its power source immediately.
Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the
protective housing of the scanner. There are no user-serviceable parts inside.
Caution: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure.
Optical: The use of optical instruments with this product will increase the eye hazard. Optical
instruments include binoculars, magnifying glasses, and microscopes but do not include normal eye
glasses worn by the user.
593-351BTE-002
No warranty of any kind is made in regard to this material, including, but not limited to, implied
warranties of merchantability or fitness for a particular purpose. We are not liable for any errors
contained herein or incidental or consequential damages in connection with furnishing, performance
or use of this material.
No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed,
or translated into any language or computer language in any form or by any means electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without express written consent and
authorization.
We reserve the right to make changes in product design without reservation and without notification.
The material in this guide is for information only and is subject to change without notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various
respective owners.
Copyright © 2009.
Scanner Outline
All rights reserved.
Introduction
This scanner is well featured with advanced wireless technology, enabling working
efficiency for simultaneous data transfer when scanning as well as working portability
as not being constrained by short of cable length. Working places as shipping industry,
cargo warehouses, superstores, pharmacies, and many more open-space or
large-scale manufacturing sites are delighted to enjoy this move-around freedom.
The cradle, a dongle or any device with wireless technology can be the host of this
scanner. All scanned data are instantly transferred to the connected host in a
100-meter connection range in open space or 75-meter range in indoor environments
(the actual communication range may vary due to indoor placement). As if out of
connection range, the embedded 32KB flash memory provides sufficient data space to
store up to 500 sets of data.
Either scanning in the handheld or stand mode, this scanner always offers a
high-accuracy and reliable scanning ability. This scanner would be your trusted tool
scanning partner.
Unpacking
This scanner package contains:
1 ea.
Wireless Single-Line Laser Scanner
1 ea.
Charging Cradle or Cradle with Radio
Communication
1 ea.
DC 9V Power Adapter
2 ea.
Ni-MH AA Recharge Battery
1 ea.
Interface Cable (only for the cradle with radio
communication)
1 ea.
Hand stripe
1 ea.
User’s Manual
If any contents are damaged or missing, please contact your dealer immediately.
Please leave this user’s manual within easy access of person using the scanner.
Cradle Host Outline
Cradle Host
The cradle host features with advanced wireless technology and designs to support
radio communication to the scanner. It the same has charging functionality.
Installing and Charging Scanner Batteries
Installing Batteries
The rechargeable batteries are packed individually for shipping safety.
Please follow the steps below to install the batteries.
Caution:
Always use the rechargeable batteries provided by the manufacturer to avoid any
non-compatible danger or void the warranty.
1.
2.
3.
Connection on Cradle Host
The scanner pairs with the cradle, when the scanner scans barcode data and passes
to cradle via radio communication, the cradle sends data to host by its interface cable.
Steps to connect the cradle to host as follows:
1.
Take the desirable interface cable and insert the RJ-45 connector to cradle
cable box until you hear a clear and short “click” sound, then connect the
other end to the host.
2.
When using Keyboard wedge and USB interface for radio communication, it
is not necessary to have an external power adapter if host has sufficient
power. But these interfaces need external power adapter when charging
batteries.
Loose the two screws enough to remove the battery cover. (It would not be
necessary to remove the screws otherwise may result in losing them.)
Insert the batteries into the scanner one by one. (positive pole to positive pole,
negative pole to negative pole)
Note: When external power adapter (9V) is available, the cradle will disregard the
power supply from host (5V).
3.
If using RS-232 interface, it is necessary to plug an external power adapter
always. Plug the power adapter into the DC-Jack of cradle cable box.
(Shown as Below)
4.
Once cradle powers up, its LED lamp lights RED for one second then turns to
flashes BLUE light. The BLUE LED means the cradle is waiting to be
connected. If the scanner pairs with this cradle, they are connected, and
BLUE LED light is always on.
Put back the battery cover, and tighten both screws.
Detach the Interface Cable
There is a hole on cradle cable box, and use a sharp pin to push down the hole while
using another hand gently pull out the interface cable to release it slowly.
Charging Batteries
For users with the charging cradle, you can connect the charging cradle with power
adapter and the scanner is now in charging.
For cradle host users, you can connect the cradle with the power adapter first, then
place the scanner into the cradle in a 30° angle and press down to make it seat tight
into the cradle; a clear and short beep is heard when position correctly into the cradle.
Press Down Here
Pairing Scanner and Cradle Host
This scanner supports three radio communication types,
Cradle Host,
SPP (Serial Protocol Profile) Slave
SPP (Serial Protocol Profile) Master.
Refer to User’s Manual for detailed description.
Paging the Scanner
Once the scanner is well situated in the cradle, press down any one of the small
buttons at the side of LED lamp to start charging (Shown as Below).
Paging the scanner often happens when you have two or more pairs of scanners and
communication cradles, and can not find which scanner pairs with its cradle.
Press any key on cradle, and it sends out a signal to its paired scanner, this scanner
beeps 3 beeps and lights BLUE LED 3 times. But if the scanner is out of its
receiving range, then it won’t react to the cradle.
The LED light in RED as in charge, and light in BLUE when full charged.
Scanning
We call this “Smart Charge”, as battery life is well depended on the charging number
of times, so only charge the batteries when necessary by following the
abovementioned procedures to prolong your battery life.
There are two ways to scan with this device.
Handheld scanning
Hands-free scanning
You may also set up auto-charging as every time the scanner is placed into the
cradle. Follow and scan the appropriate barcode symbols to set up from
programming section of this booklet.
Handheld Scanning
In the handheld scanning, hand held the scanner and simply aim at a barcode label
and push the scanner trigger to scan. Avoid aim vertically to the barcode label as a
total reflection might effect the scanning performance.
Note:
For first charging, always charge the batteries over 5 hours continuously
to prolong your battery life.
After every full charge, you may use the scanner for 8 hours continuously.
Recommended charging environment is temperature in 0°C~35°C
(32°F~95°F).
Connecting the Cradle
There are two types of cradle to select for this scanner.
Charging Cradle
Cradle Host
Charging Cradle
This cradle designs for battery charging only, it does not support radio
communication. Simply connect the external DC-9V9W power adapter into it and
place scanner into cradle to start charging.
Hands-free Scanning
Put the scanner into the cradle for hands-free scanning, and move the barcode label
approach the scanner scanning zone.
Maintenance
This device provides reliable and efficient operation with a minimum of care. Any
visibly dirty, or scratch on the scanner window will degrade reading performance,
therefore do not use abrasive wipes or tissues on the window. When the scanner is
not operating, use a soft cloth or lens tissue and gently wipe the scanning window
lens.
Do not spread liquid or submerge into liquid in any circumstance.
To know more about Pairing or Programming of this scanner, please refer to
User’s Manual or contact your sales distributor for detail set up procedures.

advertisement

Related manuals

Download PDF

advertisement