L.B. White CP125EK Owner's Manual And Instructions

Add to My manuals
30 Pages

advertisement

L.B. White CP125EK Owner's Manual And Instructions | Manualzz

Owner’s Manual and Instructions

Tradesman Kerosene Heaters

MODELS

CP045DK

CP075DK

CP125EK

CP175EK

CP210EK

OUTPUT (BTUH)

45,000

75,000

125,000

175,000

210,000

FUEL

1-K

Kerosene

Certification by:

C US

SCAN THIS QR CODE

with your smartphone or visit http://goo.gl/nvneR to view maintenance videos for L.B.White

heaters.*

*Requires an app like QR Droid for Android or

QR Reader for iPhone.

Congratulations!

You have purchased the finest kerosene portable forced air construction heater available.

manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, thank you for your confidence in our products and welcome any s uggestions or comments you may have...call us, toll-free, at (800) 345-7200 or e-mail [email protected]

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance with the requirements of Standard UL733 and ANSI A10.10-1998, CAN/CSA B140.0-03 and CSA B140.8 - 1967 and is listed and approved as a Kerosene forced-air construction heater with application for the temporary heating of buildings under construction, alteration, or repair. If you are considering using this product for any application other than its intended use, then please contact the L.B. White Co., Inc.

Quality heaters you can count on.

411 Mason St., Onalaska, WI 54650 • (800) 345-7200 • (608)783-5691 • (608) 783-6115, fax • [email protected]

150-28814

1

GENERAL HAZARD WARNING

Failure to comply with the precautions and instructions provided with this heater, can result in:

— Death

— Serious bodily injury or burns

— Property damage or loss from fire or explosion

— Asphyxiation due to lack of adequate air supply or carbon monoxide poisoning

— Electrical shock

Read this Owner’s Manual before installing or using this product.

Only properly-trained service people should repair or install this heater.

Save this Owner’s Manual for future use and reference.

Owner’s Manuals and replacement labels are available at no charge.

See website, or for assistance, contact

L.B. White at 800-345-7200.

of life.

WARNING

Fire and Explosion Hazard

Not for home or recreational vehicle use.

Installation of this heater in a home or recreational vehicle may result in a fire or explosion.

Fire or explosions can cause property damage or loss

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING

Fire and Explosion Hazard

Keep solid combustibles a safe distance away from the heater.

Solid combustibles include wood, paper, or plastic products, building materials and dust.

Do not use the heater in spaces which contain or may contain volatile or airborne combustibles.

Volatile or airborne combustibles include gasoline, solvents, paint thinner, dust particles or unknown chemicals.

Failure to follow these instructions may result in a fire or explosion.

Fire or explosions can lead to property damage, personal injury or loss of life.

IMKFAT-GCU

Table of Contents

SECTION PAGE

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Heater Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Information

2

3

5

5

Installation & Assembly

Heater Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Operation

7

8

Overview of Heater Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

The Safety System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Fueling Your Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

To Start Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

To Shutdown Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

To Restart Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Extra Electrical Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

11

10

10

10

10

9

9

9

10

Longterm Storage of Your Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Maintenance

Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Air Intake Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Air Output /Lint Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Rotor/Vanes, Rotor Insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Fan Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

S p a r k P l g

13

14

15

15

12

12

12

12 u .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

.

..

1 5

Photocell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Pump Pressure Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Replacing Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

20

16

16

17

18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Parts Identification

Parts Schematic (CP045DK & CP075DK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Parts List (CP045DK & CP075DK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Parts Schematic (CP125EK & CP175EK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Parts List (CP125EK & CP175EK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Parts Schematic (CP210EK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Parts List (CP210EK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

27

28

General Information

This Owner’s Manual includes all options and accessories commonly used on this heater.

When calling for technical service assistance, or for other specific information, always have model number, configuration number and serial number available. This information is contained on the dataplate.

This manual will instruct you in the operation and care of your unit. Have your qualified installer review this manual with you so that you fully understand the heater and how it functions.

The installation, repair, and servicing of the heater requires continuing expert training and knowledge of kerosene heaters and should not be attempted by anyone who is not so qualified.

Contact your local L.B. White distributor or the L.B. White

Co., Inc. for assistance, or if you have any questions about the use of the equipment or its application.

The L.B. White Co., Inc. has a policy of continuous product improvement. It reser ves the right to change specifications and design without notice.

2

3

SPECIFICATIONS CP045DK

Fuel Type

Heater Specifications

Model

CP075DK

1-K, Kerosene

Max Input (BTUH) 45,000

Pump Pressure (psig) 2.8

Fuel Consumption per Hour (gal) .35

75,000

3.8

.57

Motor Characteristics

Ball Bearing

1/8 HP, 3,300 RPM 1/8 HP, 3120 RPM

Electrical Supply (Voltz/Hz/Phase) 120/60/1

Amp Draw

CONTINUOUS

OPERATION

1.6

1.6

Dimensions (Inches) Length x width x height 32” x 11.8” x 16.8”

Minumum Safe

Distances From

Nearest

Combustible

Materials

TOP

SIDES

BACK

BLOWER OUTLET

BULK FUEL STORAGE CONTAINER

Net Weight (Lbs.)

27.6

Shipping Weight (Lbs.) 32.0

Minimum Ambient Temperature in Which Heater May Be Used

4 ft.

4 ft.

4 ft.

8 ft.

25 ft.

-20 o

F

27.6

32.0

SPECIFICATIONS

Fuel Type

Max Input (BTUH)

CP125EK

125,000

Heater Specifications

Model

CP210EK CP175EK

1-K, Kerosene

175,000 210,000

Pump Pressure (PSIG)

Fuel Consumption per Hour (gal)

Motor Characteristics

Electrical Supply (Voltz/Hz/Phase)

Amp Draw

Length x Width x Height

Minumum Safe

Distances From

Nearest

Combustible

Materials

Net Weight (lbs.)

Shipping Weight (lbs.)

Minimum Ambient Temperature in which Heater may be used

5.5

.95

1/5HP 3455 RPM

7.5

1.32

Ball Bearing

1/4HP 3430 RPM 1/3HP 3380 RPM

120/60/1

8.5

1.6

3.2

3.7

CONTINUOUS

OPERATION

2.5

36.1” x 21.5” x 24.6”

Top

Sides

Back

Blower Outlet

Bulk Fuel Storage Container

58.6

65.9

41.8” x 23.1” x 26.1”

4 ft.

4 ft.

4 ft.

8 ft.

25 ft.

65.0

73.9

-20 o

F

66.6

75.4

4

5

Safety Information

HAZARD DEFINITIONS

DANGER

Indicates an imminently hazardous situation which, if not avoided WILL result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.

GENERAL SAFETY INFORMATION

WARNING

Before using this heater, please read this USER’S

MANUAL very carefully. This USER’S MANUAL has been designed to instruct you as to the proper manner in which to assemble, maintain, store, and most importantly, how to operate the heater in a safe and efficient manner.

WARNING

Never leave the heater unattended while burning!

DANGER

Improper use of this heater can result in serious injury or death from burns, fire, explosion, electrical shock, and/or carbon monoxide poisoning.

WARNING

Risk of CO Poisoning!

- Use this heater only in well ventilated areas.

Provide proper ventilation. Proper ventilation air for combustion must be provided in accordance with

OSHA 29 CFR 1926.154, Temporary Heating Devices.

ANSI A 10.10, Safety Requirements for Temporary and Portable Space Heating Devices, or the Natural

Gas and Propane Installation Code, CAN/CSA B149.1 as appropriate.

GENERAL SAFETY INFORMATION (cont.)

CANADIAN RESIDENTS:

Use of this heater shall be in accor dance with authorities having juris diction and

CSA Standard B139.

NEW YORK CITY RESIDENTS: For use only at construction sites in accordance with applicable NYC codes under

NYCFD certificate of approval #5034 and 5037

- Never use this heater in living or sleeping areas.

- Carbon Monoxide Poisoning: Early signs of carbon

such as headaches, dizziness, and/or nausea. If you

have these symptoms, your heater may not be

working properly.

- Get fresh air at once! Have the heater serviced.

- People with breathing problems should consult a

physician before using the heater.

WARNING

Risk of Burns/Fire/Explosion!

- Keep all combustible materials away from this heater.

Minimum Clearances

Outlet 8 feet (250 cm)

Sides, Top and Rear 4 feet (125 cm)

- NEVER use fuels such as gasoline, benzene, paint

thinners, or other oil compounds in this heater

(RISK OF FIRE OR EXPLOSION).

be present.

WARNING

Risk of Electric Shock!

- Use only the electrical power (voltage and

heater. Use only a three prong, grounded outlet and

extension cord.

- ALWAYS install the heater so that it is not directly

exposed to water spray, rain, dripping water, or wind.

- ALWAYS unplug the heater when not in use.

CALIFORNIA RESIDENTS: This heater produces carbon monoxide, which is listed by the State of California as a reproductive toxin under Proposition 65.

MASSACHUSETTS RESIDENTS:

Massachusetts state law prohibits the use of this heater in any building which is used in whole or in part for human habitation. Use of this heating device in Massachusetts requires local fire dept. permit (M.E.L.C. 148, Section 10A).

operating or still hot. This heater is EXTREMELY HOT

while in operation.

- NEVER block air inlet (rear) or air outlet (front) of

heater.

- NEVER use duct work in front or at rear of heater.

- NEVER move or handle heater while still hot.

- NEVER transport heater with fuel in its tank.

- When used with optional thermostat or if equipped

with a thermostat, the heater may start at any time.

- ALWAYS locate heater on a stable and level surface.

- Use 1-K kerosene in this heater. #1 fuel oil is a

suitable substitute.

- Bulk fuel storage should be a minimum of 25 ft. from

heaters, torches, portable generators, or other sources

of ignition. All fuel storage should be in accordance

with federal, state, or local authorities having jurisdiction.

6

7

Installation and Assembly Instructions

HEATER SPECIFICATIONS

Introduction

Please read this USER’S MANUAL carefully. It will show you how to assemble, maintain and operate this heater safely

Product Features

features.

Consumer: Retain these instructions for future reference.

Unpacking

1. Remove all packing items applied to heater for

shipment.

2. Remove all items from carton.

3. Check all items for shipping damage.

If heater is damaged, promptly inform dealer where you

purchased heater.

Dimen sions

46

0 PSI

8

10

14

16 3/4"

Fan Guard

Hot Air Outlet

Lower Shell

Fuel Tank

Side Cover

Lamp

Thermostat Knob

(CP075DK model only)

LED Power/Reset Switch

Upper Shell

Handle

Pressure Gauge

Cord Wrap

Fuel Gauge

Fuel Cap

Power Cord

Figure 2.1 - Features

32"

11 3/4"

M DK aanndd CCPP007755 DK

Figure 1.1 - Heater Dimensions

Dimen sions

L

Figure 1.2 - Heater Dimensions

Height

Length

Width

CP125EK

24.6”

36.1”

21.5”

2

6 10

W

CP175EK

CP210EK

26.1”

41.8”

23.1”

H

Product Features

Handle Front

Hot Air Outlet

Upper Shell

Lower Shell

Fuel Gauge

Fuel Cap

Side Cover

Lamp

Thermostat

Knob

Figure 2.2 - Features

Pressure Gauge

Cord Wrap

Handle Rear

P ower Cord

(Piggy Back)

Power/Reset Switch

Room Temp. Display

Installation and Assembly Instructions

ASSEMBLY

TOOLS REQUIRED

CP045DK/CP075DK

- Medium Phillips screwdriver.

on the upper housing.

2. Align the holes in upper housing with two mounting holes on the handle as shown in Figure 4.

3. Secure handle with screws provided.

4. Insert cord wrap into the rectangle holes on the supporter and align the hole on the cord wrap with

the mounting hole on the side covers shown in Figure 4.

5. Secure cord wrap with screws provided.

CP125EK/CP175EK/CP210EK

- Medium Phillips screwdriver.

- M5 open, or adjustable wrench.

1. Slide threaded axle through the rear section of the wheel support frame.

2. Slide one axle bushing on to each side of the axle. Slide one wheel on to each side of the axle.

3. Attach one cap nut on to each side of the threaded axle and tighten well.

4. Place heater on wheel support frame. Make sure the air inlet end (rear) of heater is over wheels. Align the holes on fuel

6. Align the hole on the handle (front and rear) with the mounting hole on the cord wrap.

WARNING

Fire or explosion hazard!

- Do not operate heater without support frame fully

assembled to tank.

Model

Wheel Support Frame

Wheels

Front-Handle

Rear-Handle

Axle

Cord Wrap

H ardware Kit

Handle

CCPP004455 DK // CCPP007755 DK M

Handle

Hardware Kit

Cord Wraps

Wheels

CP125 EK / CP175 EK / CP210 EK

Screws

Flange Screws

Nuts

Cord Wraps

Cap Nut S

Bushings

Cap Nuts L

Front Handle

CP045DK/CP075DK CP125EK CP175EK CP210EK

No

Yes

Yes

Yes

No

No

No

No

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

Yes

Yes

Yes

No

Yes

Yes

Yes

Yes

Screw

Handle

Front Guard

Wedged

Portion

Slit Hole

Side Cover

Supporter

Cord Wrap

Screw

FFiigguurree 44 – Handle and Cord Wrap Installation CP045DK and CP075DK

Wheel Support Frame

Axle

Rear Handle

8

Assembly

(cont.)

Front Handle

Hot Air Outlet

Screw

Flange Screw

Cord Wrap

Rear Handle

Cap Nut S

Air Inlet

Fuel Tank

Flange

OPERATION

Wheel Support Frame

Nut

Figure 5 - Assembly

Wheel

Cap Nut L

Axle

Wheel Bushing

Figure 6 – Overview of Heater Design

OVERVIEW OF HEATER DESIGN

Fuel System: This heater is equipped with an electric air pump that forces air through the air line connected to the fuel intake, and then through a nozzle in the burner head.

When air passes in front of the fuel intake, it causes fuel to rise from the tank and into the burner nozzle.

This fuel and air mixture is then sprayed into the

SureFire Ignition: The electronic ignitor sends voltage to a specially designed spark plug. The spark plug ignites the fuel and air mixture described above.

The Air System:

The heavy duty motor turns a fan that forces air into and around the combustion chamber. Here, the air is heated and then forced out the front of the heater.

THE SAFETY SYSTEM

Temperature Limit Control: This heater is equipped with a Temperature Limit Control designed to turn the heater off should the internal temperature rise to an unsafe level.

If this device activates and turns your heater off, it may require service.

Once the temperature falls below the reset temperature, you will be able to start your heater.

Model Internal Shut-off

Temp.+/-10 Degrees

Reset Temp.

+/-10 Degrees

9

CP045DK/CP075DK

CP125EK

CP175EK

CP210EK

176°F/80°C

230°F/110°C

158°F/70°C

194°F/90°C

122°F/50°C

194°F/90°C

104°F/40°C

140°F/60°C

Electrical System Protection: This heater’s electrical system is protected by a fuse mounted to the PCB

Assembly that protects it and other electrical components from damage. If your heater fails to operate, check this

Flame-Out Sensor: Utilizes a photocell to monitor the extinguish.

FUEL SPECIFICATIONS

KEROSENE (1-K)

For optimal performance of this heater, it is strongly suggested that 1-K kero sene be used. 1-K kerosene has as sulfur, which can cause a rotten egg odor during the operation of the heater. However, #1 or #2 fuel oil (diesel fuel) may also be used if 1-K kerosene is not available. Be advised that these fuels do not burn as clean as 1-K kerosene, and care should be taken to provide more fresh air ventilation to accommodate any added contaminants that may be added to the heated space.

WARNING

Fire or explosion hazard!

- Kerosene should only be stored in a blue container

that is clearly marked “kerosene”. Never store

kero sene in a red container. Red is associated with

gasoline.

- NEVER store kerosene in the living space. Kerosene

should be stored in a well ventilated area outside

the living area.

- NEVER use fuel such as gasoline, benzene, alcohol,

white gas, camp stove fuel, paint thinners, or other

oil compounds in this heater (THESE ARE VOLATILE

FUELS THAT CAN CAUSE A FIRE OR EXPLOSION).

- NEVER store kerosene in direct sunlight or near a

source of heat.

- NEVER use kerosene that has been stored from one

season to the next. Kerosene deteriorates over time.

OLD KEROSENE WILL NOT BURN PROPERLY IN THIS

HEATER.

- Use 1-K kerosene in this heater. #1 fuel is a suitable

substitute.

FUELING YOUR HEATER

tank outdoors.

WARNING

Fire and explosion hazard!

still hot.

IMPORTANT : REGARDING FIRST IGNITION OF be done OUTDOORS. This allows the oils, etc., used in manufacturing heater to be burned off outside.

TO START HEATER

1. Fill fuel tank with kerosene or No. 1 fuel oil.

2. Attach fuel cap.

3. Plug power cord into three prong, grounded extension

cord. Extension cord must be at least six feet long.

- Extension Cord Wire Size Requirements:

- 6 to 100 feet (1.8 to 30.53 meters) long, use 16

AWG conductor.

- 101 to 200 feet (30.8 to 61 meters) long, use 14

AWG conductor.

NO THERMOSTAT ON 45

4. Turn thermostat control knob to desired setting and

push power switch to “ON” position. Power lamp will

light and heater will start.

NOTE

: Room Temp. display indicates as following:

- When room temp. is less than 0

ºF

: “lo”.

- When room temp. is between 0

ºF

and 99

ºF

:

“Temp. is Displayed”

- W h e n r o o m t e m p i s g r e a t e r t h a n 9 9

ºF

: “Hi”

If heater does not start, the thermostat setting may be too low. Turn THERMOSTAT CONTROL

KNOB to higher position to start heater. If heater still does not start, turn power switch to “OFF” and then to “ON” position (See Figure 7.1 &7.2)

If heater still does not start, see Troubleshooting on page 18.

NOTE: The major electrical components of this heater are protected by a safety fuse mounted to the PCB board. If your heater fails to start, check should also check your power source to insure that proper voltage and frequency are being supplied to the heater.

OPERATION (cont.)

TO SHUT DOWN HEATER

Turn switch to “OFF” and unplug power cord.

Model CP045DK

Lamp

Lamp

Model CP075DK

Power/Reset

Switch

Power/Reset Switch

Figure 7.1 - Controls

Thermostat Control Knob

Model CP125EK, CP175EK, CP210EK

Lamp Room Temp. Display

Power/Reset

Switch

Thermostat

Control Knob

Figure 7.1 - Controls

TO RESTART HEATER

1. Wait 10 seconds after stopping heater.

2. Repeat steps under, “TO START HEATER.”

PIGGYBACK POWER CORD

Cover

Electric Outlet

Figure 7.2 - Controls

WARNING

SHOCK HAZARD!

• Always cover electric outlet when not in use.

Don’t plug and use an appliance of more than

5A current in this outlet.

10

OPERATION (cont.)

LONG-TERM STORAGE OF YOUR HEATER

FUEL TANK DRAIN CP045DK & CP075DK

1. Drain fuel tank through fuel cap opening.

2. Using a small amount of kerosene, swirl and rinse the

inside of the tank.

NEVER MIX WATER WITH KEROSENE, as it will cause rust inside the tank. Pour the kerosene out, making sure that you remove it all.

IMPORTANT: Do not store kerosene over summer for use during next heating season. Using old fuel may damage heater.

3. Reinstall fuel cap. Properly dispose of old and

dirty fuel.

- Make sure storage place is free of dust and corrosive

fumes.

- Store the heater in the original box with the original

packing material and keep USER’S MANUAL with

heater.

IMPORTANT: Do not store kerosene over summer for use during next heating season. Using old fuel may damage heater.

3. Tighten drain bolt firmly into the tank, otherwise it will

not seal completely.

- Make sure storage place is free of dust and corrosive

fumes.

- Store the heater in the original box with the original

packing material and keep USER’S MANUAL with heater.

FUEL TANK DRAIN CP125EK & CP175EK & CP210EK

1. Remove drain bolt from bottom of fuel tank . See

Figure 9.

Figure 9 – Drain Plug Removal

1. Using a small amount of kerosene, swirl and rinse the

inside of the tank.

NEVER MIX WATER WITH KEROSENE, as it will cause rust inside the tank. Pour the kerosene out, making sure that you remove it all.

11

MAINTENANCE

USE ORIGINAL EQUIPMENT REPLACE MENT PARTS. Use of third-party or other alternate components will void warranty and may cause unsafe operating conditions.

WARNING

Fire or explosion hazard!

•Never service heater while it is plugged in or while hot!

REPLACE EVERY 500 HOURS OF OPERATION OR ONCE A

YEAR

- Remove upper shell and fan guard (See Air Intake Filter

Figure 10).

- Turn air pressure gauge counter-clockwise and remove.

screwdriver.

FUEL TANK

FLUSH EVERY 200 HOURS OF OPERATION OR AS NEEDED

(See Longterm Storage, page 11).

AIR INTAKE FILTER

Screw

Upper Shell

Air Intake Filter

- Reinstall fan guard and upper shell.

PUMP SERVICING

●PUMP ROTOR

Pump Body

Fan Guard

Screw

Vane

End Pump Cover

Figure 10 - Air Filter Access

WASH AND DRY WITH SOAP AND WATER EVERY 500 HOURS

OF OPERATION, OR AS NEEDED.

- Remove screws along each side of heater using medium

Phillips screwdriver.

- Lift off upper shell.

- Remove fan guard.

- Reinstall fan guard and upper shell.

AIR OUTPUT FILTER, LINT FILTER

Air Output Filter

End Filter Cover

Screw

Rotor Insert

Screw

Rotor

Figure 12 - Rotor Pump Assembly

REPLACE IF CHIPPED, CRACKED OR AS NEEDED

- Remove upper shell and fan guard (See Air Intake

Filter Figure 10).

- Turn air pressure gauge counter-clockwise and

remove.

Phillips Screwdriver (See Air Output Filter, Lint Filter

Figure 11).

- Remove end pump cover screws using a 5/16”

(8mm) nut driver/socket.

- Replace rotor, all 4 vanes and plastic rotor insert. All

of these components must be replaced at the same

time.

Lint Filter

Air Pressure Gauge

Figure 11 - Filter Assembly

Air Intake Filter

12

13

PUMP SERVICING (cont.)

●ROTOR GAPPING

IMPORTANT: The newly inserted rotor must be gapped properly before you reinstall the end pump cover.

MAINTENANCE (cont.)

●END FILTER COVER & GASKET(LEAKING)

REPLACE IF SPLIT ,CRACKED OR AS NEEDED.

- Replace End filter cover.(See Air output filter,page 12)

- Replace Air ouput filter.(See Air output filter,page 12)

Rotor Gap Pump Body Screw

FAN BLADES

Flush

Set Screw

Motor Shaft

Rotor

Pump Body

Figure 13 - Rotor Gapping

- Slightly loosen the pump body screws using a medium

screw driver.

- Position pump body to set rotor gap to .003’’~.004’’ at top

dead center and retighten pump body screws.

- Verify the gap using calipers, a micrometer or a dollar bill.

- Reinstall the end pump cover.

- Reinstall air output filter and lint filter.

- Reinstall end filter cover and air pressure gauge.

- Reinstall fan guard and upper shell.

●AIR LINE (LEAKING)

REPLACE IF SPLIT, CRACKED OR AS NEEDED.

- Remove air line from air line fitting (See Figure 14) and from nozzle adaptor.(See Nozzle, page 14)

- Reinstall Air line to air line fitting and nozzle adaptor.

Air Line Fitting

Gasket

Air Outfilter Filter

End Filter Cover

Air Line

Air Line

Fan Blade

Motor

Figure 15 - Fan Assembly

CLEAN EVERY SEASON OR AS NEEDED

- Remove upper shell (See Air Intake Filter Figure 10).

- Use M6 Allen wrench to loosen set screw which holds fan

blade to motor shaft.

- Slip fan blade off motor shaft.

- Clean fan blade using soft cloth moistened with kerosene

or solvent.

- Dry fan blade thoroughly.

- Reinstall fan blade to motor shaft.

- Place fan blade hub flush with end of motor shaft.

- Place set screw on flat of shaft.

- Tighten screw firmly (40-50 inch-pounds/4.5-5.6 N-m).

Reinstall upper shell.

Figure 14 - Check Air leaks around Pump.

MAINTENANCE (cont.)

NOZZLE

Combustion Chamber

Screw

Ignitor Wire

Fuel Line

Air Line

Spark Plug

Nozzle Adaptor

Burner Head

Combustion Chamber

Screw

Ignitor Wire

Fuel Line

Spark Plug

Nozzle Adaptor

Bracket-Burner

Air Line

Nozzle Face

Nozzle Adaptor

Nozzle

Nozzle Adaptor

Figure 16 – Nozzle Replacement For Models CP045DK-CP175EK

CLEAN NOZZLE AS NEEDED

(For Models CP045DK - CP175EK only)

- Remove upper shell (See Air Intake Filter, page 12).

- Remove fan blade (See Fan Blades).

- Remove fuel and air line hoses from nozzle adaptor.

- Remove ignitor wire from spark plug.

- Remove spark plug from nozzle adaptor using medium

phillips screwdriver.

- Turn nozzle adaptor 1/9 turn(40°) to counter clock wise

and pull toward motor to remove. (See Figure 16)

- Place plastic hex-body into vise and lightly tighten.

- Carefully remove nozzle from burner head using 5/8”

socket wrench.

- Blow compressed air through face of nozzle.

(this will remove any dirty in nozzle)

- Reinstall nozzle into nozzle adaptor until nozzle seats.

Tighten 1/3 turn more using 5/8” socket wrench.

(40~45 inch-pounds)

- Reinstall nozzle adaptor to burner head.

- Reinstall spark plug to nozzle adaptor.

- Attach ignitor wire to spark plug.

- Attach fuel and air line hoses to nozzle adaptor.

- Reinstall fan blade and upper shell.

Nozzle Face

Nozzle Adaptor

Nozzle

Nozzle Adaptor

Figure 17 – Nozzle Replacement CP210EK

(For Model CP210EK Only)

- Remove upper shell (See Air Intake Filter, page 12).

- Remove fan blade (See Fan Blades, page 13).

- Remove fuel and air line hoses from nozzle adaptor.

- Remove ignitor wire from spark plug.

- Remove spark plug from nozzle adaptor using medium

phillips screwdriver.

- Turn nozzle adaptor 1/8 turn (45°) to counter clock wise

and pull toward motor to remove. (See Figure 17)

- Place plastic hex-body into vise and lightly tighten.

- Carefully remove nozzle from adaptor-nozzle using 5/8”

socket wrench.

- Blow compressed air through face of nozzle.

(this will remove any dirt in nozzle)

- Reinstall nozzle into nozzle adaptor until nozzle seats

Tighten 1/3 turn more using 5/8” socket wrench

(40~45 inch-pounds)

- Reinstall nozzle adaptor to burner bracket

- Reinstall spark plug to nozzle adaptor.

- Attach ignitor wire to spark plug.

- Attach fuel and air line hoses to nozzle adaptor.

- Reinstall fan blade and upper shell.

14

SPARK PLUG

CLEAN AND REGAP EVERY 600 HOURS OF OPERATION OR

REPLACE AS NEEDED.

Screw

Spark Plug

Nozzle Adaptor

Spark Plug

Ignitor Wire

PHOTOCELL

MAINTENANCE (cont.)

Side Cover

Screw

PhotocellWire

Switch

Wires

Bracket

Install Photocell

Incorrect

Correct

Photocell

Lens

Figure 18 – Spark Plug Replacement

(For Models CP045DK-CP175EK)

- Remove upper shell (See Air Intake Filter, page 12).

- Remove fan (See Fan Blades, page 13).

- Remove ignitor wire from spark plug.

- Remove spark plug from nozzle adaptor using

medium phillips screwdriver.

- Clean and regap spark plug electrodes to 3.5mm gap.

- Reinstall spark plug to nozzle adaptor.

- Attach ignitor wire to spark plug.

- Reinstall fan and upper shell.

Figure 20 – Photocell Replacement

CLEAN PHOTOCELL ANNUALLY OR AS NEEDED.

- Remove upper shell (See Air Intake Filter, page 12)

- Remove fan (See Fan Blades, page 13)

- Remove photocell from its mounting bracket.

- Clean photocell lens with cotton swab.

TO REPLACE: Remove side cover near power switch.

- Disconnect wires from power switch and remove

side cover.

- Disconnect wires from circuit board and remove

photocell.

- Install new photocell and attach wires to circuit board

- Replace switch wires to power switch and side cover.

- Replace fan and upper shell.

Nozzle Adaptor

Spark Plug

Screw

Spark Plug

Ignitor Wire

Figure 19 – Spark Plug Replacement

(For Model CP210EK only)

- Remove upper shell (See Air Intake Filter, page 12).

- Remove fan (See Fan Blades, page 13).

- Remove ignitor wire from spark plug.

- Remove spark plug from nozzle adaptor using mediumphillips screwdriver.

- Clean and regap spark plug electrodes to 3.5mm gap.

- Reinstall spark plug to nozzle adaptor.

- Attach ignitor wire to spark plug.

- Reinstall fan and upper shell.

15

MAINTENANCE (cont.)

FUEL FILTER

CLEAN OR REPLACE TWICE PER HEATING SEASON OR AS

NEEDED.

Fuel Filter

Fuel Line

Switch Wires

PUMP PRESSURE ADJUSTMENT

Flat blade

Screwdriver

Screw

Side Cover

Power Switch

Figure 21 – Fuel Filter Replacement

- Remove side cover screws using medium Phillips

screwdriver.

- Disconnect switch wires from power switch and remove

side cover.

- Reinstall side cover.

Relief Valve

Figure 22 – Adjusting Pump Pressure

- Start heater (See “Operation”, page 9).

- Allow motor to reach full speed.

- Turn relief valve clockwise to increase pressure.

- Turn relief valve counterclockwise to decrease

pressure.

- Set pump pressure to correct pressure for each

model.

- Stop heater (see “Operation”, page 9).

Model

CP045DK

CP075DK

CP125EK

CP175EK

CP210EK

Pump Pressure

2.8 PSI

3.8 PSI

5.5 PSI

7.5 PSI

8.5 PSI

NOTE: USE ONLY ORIGINAL EQUIPMENT

REPLACEMENT PARTS. Use of alternate or third party components will void warranty and may cause an unsafe operating condition.

16

MAINTENANCE (cont.)

REPLACING FUSE

NOTE: The heater is fuse protected. If your heater fails to ignite, DO NOT

RETURN YOUR HEATER TO THE STORE.

Please follow the simple instructions below to inspect and change the fuse.

- Unplug heater.

- Remove side cover screws using medium Phillips screwdriver.

WARNING

Burn hazard!

•SHOCK HAZARD. To prevent presonal injury, unplug the

power cord before replacing fuse.

- Remove fuse from fuse holder (See Figure 23).

- Replace fuse with enclosed fuse.

- Replace switch wires to power switch.

- Replace side cover.

NOTE:

Fuse

Fuse Holder

Model : CP075DK

Side Cover

Power

Switch

Screw

Switch

Wires

Fuse

Fuse

Fuse Holder

Model : CP045DK

Fuse Holder

Figure 23 – Replacing Fuse

17

WIRING DIAGRAM

DISPLAY PCB

POWER LAMP

(LED)

CN1

2P

CN1

PHOTO CELL

CONTROL PCB

PW-W/H

PW-BLK

CN3

CN7

RED

RED

ORANGE

RED

BLACK

SPARK PLUG

IGNITOR

BLACK

BLACK

PUMP

MOTOR WHITE

GREEN

CAPACITOR

15uF/230VAC

EARTH

BLACK

BLACK

CN2

POWER

PLUG

BLACK

GREEN

POWER

SWITCH

BLACK

LIMIT

CONTROL

WHITE

FUSE

8A/125VAC

EARTH

Figure 24 - Wiring Diagram Model CP045DK

POWER LAMP

(LED)

CONTROL PCB

ROOM

SENSOR

CN6

CN2(AC2)/ WHT

CN1(AC1)/ BLK

CN4

CN3

RED

BLACK

SPARK PLUG

RED

IGNITOR

BLACK

ORANGE

RED

PUMP

MOTOR

GREEN

BLACK

WHITE

CAPACITOR

15uF/230VAC

EARTH

PHOTO

CELL

THERMOSTAT

(TEMP. CONTROL)

BLACK

CN5

BLACK

AC120V

60Hz

POWER

PLUG

BLACK

GREEN

POWER

SWITCH

BLACK

LIMIT

CONTROL

WHITE

FUSE

8A/125VAC

EARTH

Figure 25 - Wiring Diagram Model CP075DK

18

19

WIRING DIAGRAM

POWER LAMP

(LED)

PHOTO

CELL

THERMOSTAT

(TEMP. CONTROL)

BLACK

CN5

BLACK

CONTROL PCB

ROOM

SENSOR

CN6

CN2(AC2)/ WHT

CN1(AC1)/ BLK

CN4

CN3

RED

BLACK

SPARK PLUG

RED

IGNITOR

BLACK

ORANGE

RED

BLACK

PUMP

MOTOR WHITE

GREEN

CAPACITOR

20uF/350VAC

EARTH

POWER

PLUG

BLACK

GREEN

POWER

SWITCH

BLACK

LIMIT

CONTROL

WHITE

FUSE

8A/125VAC

EARTH

Figure 26 – Wiring Diagram Models CP125EK, CP175EK, CP210EK

Troubleshooting

Symptom

Heater ignites but MAIN PCB assembly shuts heater off after a short period of time. (Indicator display indicates “E1”)

Heater will not ignite but motor runs for a short period of time.

room temp. display indicates

“E1”)

Possible (Cause(s))

1. Wrong pump pressure

2. Dirty a ir output, a ir Intake or l int lilter

3. Dirty f uel f ilter

4. Dirt in n ozzle

5. Dirty p hotocell lens

6. Photocell a ssembly not p roperly I nstalled (not

7. Bad electrical connection between photocell and

MAIN PCB a ssembly.

8. Defective photocell

9. Cracks in e nd filter cover.

10. Defective r otor& v ane.

11. Splits/cracks on a ir line.

12. Air leaks around the pump area.

1. No fuel in tank

2. Wrong pump pressure

3. Carbon deposits on spark plug and/or improper

gap

5. Dirt in n ozzle

6. Water in fuel tank

7. Bad electrical connection between igniter and

MAIN PCB Assembly

8. Igniter wire is not attached to spark plug

Corrective Action

1. See Pump Pressure Adjustment, page 16

2. See Air Output, Air Intake and Lint Filters, page 13

3. See Fuel Filter, page 16

4. See Nozzle, page 14

5. Clean Photocell Lens, page 15

6. Make sure photocell boot is properly seated in

bracket, Page 15

7. Check electrical components. See Wiring Diagrams,

page 18

8. Replace Photocell, page 15

9. Check for cracks in e nd filter cover.

Replace if cracked,page 13

10. Check r otor & v ane condition.

Replace if chipped,cracked,page 12

11. Check a ir line for splits/cracks.

Replace if splited,cracked,page 13

12. Check a ir leaks around the pump area,page 13

1. Fill tank with kerosene

2. See Pump Pressure Adjustment, page 16

3. See Spark Plug, page 15

4. See Fuel Filter, page 16

5. See Nozzle, page 14

6. Flush fuel tank with clean kerosene, page 12

7. Check electrical components. See Wiring Diagram,

page 18

8. Attach igniter to spark plug. See Spark Plug, page 15

Fan does not turn when heater is plugged in and power switch was in the “ON” position. (Indicator room temp. display indicates “E2”) room temp. display indicates “E3”)

Heater will not turn-on (Indicator

Lamp is off)

1. Thermostat setting is too low

2. Bad electrical connection between motor and MAIN

PCB Assembly

3. Jammed/shattered rotor

1. Turn thermostat control knob to a higher setting

2. Check electrical connections. See Wiring Diagram, page 18

3. See Servicing Pump, page 12.

1. Sensor f ailure 1. Replace sensor. See Wiring Diagram, page 18

1. Thermostat switch failure

2. Temperature limit safety device is overheated

3. No electrical power

4. Blown fuse

5. Bad electrical connection between temperature

limit safety device and PCB board

1. Replace MAIN PCB

2. Turn power switch to “OFF” and allow to cool (about 10 min.)

3. Check to insure heater cord and extension cord are

plugged in. Check power supply

4. Replace safety fuse in PCB board. See Replacing

Fuse, page 17

5. Check electrical connections. See Wiring Diagrams page 18

20

Parts Identification

PARTS SCHEMATIC (CP045DK, CP075DK)

For Repair Parts, call 1-800-345-7200

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

26

23

24

14-1

14-2

14-3

17-1

17-3

11

17-2

17-4

17-7

17-8

17-9

25

12

21

22

20

13

14

19

17-5

10

17-6

1

6

9

16

17

3

2

7

8

15

18

4

5

Figure 27– Repair Parts Illustration for Portable Oil-Fired Heaters Models CP045DK, CP075DK

21

14-4

Parts List (CP045DK, CP075DK)

Reference

Number Description

Part Number for Models:

CP045DK CP075DK

1 Fuel Tank Assembly 572701 572700

2 Fuel Gauge

572454

3 Fuel Cap ----------

573414

----------

4 Panel Right Side Assembly 572920

5 Power Switch ---------572251 ----------

572919

6 Display P.C.B. Assembly 572162

7 Power Cord ---------

8 Panel Left Side Assembly 572254

-----

572159 ---------

572257

9 Ignition Transformer ---------573399 ----------

10 Fuel Filter ---------572154----------

11 Combustion Chamber

12 Photocell Bracket

572698

572184

572699

572 185

13 Photocell Assembly

14 Burner Head Assembly

14-1 Burner Head

----------572186----------

572901

----------572692----------

14-2 Nozzle Assembly

14-3 Nozzle Adaptor

572192

----------572652---------

14-4 Spark Plug Assembly ----------572200----------

15 Fan Guard ----------572265----------

16 Fan Assembly 572232

17 Motor and Pump Assembly

17-1 Motor

----------572651----------

----------572694----------

17-2 Capacitor

17-3 Motor Support

----------572650----------

----------572695----------

17-4 Pump Body ----------572223----------

572903

572193

572233

17-5 Filter Kit* ----------572227----------

17-6 Pump Adjustment Kit*** ----------572230----------

17-7 Rotor Kit** ----------572225----------

17-8 Pump Cover ----------572696----------

17-9 Filter Cover ----------572229----------

18 Pressure Gauge ----------572231----------

19 Main P.C.B. Assembly

20 Air/Fuel Lines

572653

----------572691----------

21 Clip Nut (8-Pack) ----------572284----------

22 Temperature Limit Assembly

----------572726---------

23 Screw (12-Pack) ----------572282----------

24 Upper Shell

----------572697---------

25 Lower Shell

----------572693----------

26 Front Guard ----------572270----------

Fuse ----------572447----------

Hardware Kit ----------572324----------

Pump/Filter Cover Screws (10-Pack) ----------572283----------

Filter Kit* - Includes Intake, Outlet, and Lint Filter

Rotor Kit** - Include Rotor, Blades, and Insert

Pump Adjustment Kit*** - Includes Ball Spring and Adjusting Screw

573403

22

Parts Identification

PARTS SCHEMATIC (CP125EK & CP175EK)

For Repair Parts, call 1-800-345-7200

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

14-4

24

23

14-1

14-2

17-1

17-3

11

17-2

17-4

17-5

17-8

17-9

17-10

25

12

21

17-6

22

10

20

17-7

1

2

13

14

19

9

16

17

3

4

5

Figure 28– Repair Parts Illustration for Portable Oil-Fired Heaters Models CP125EK, CP175EK

23

6

7

18

8

14-3

15

PARTS LIST (CP125EK & CP175EK)

Reference

Number Description

Part Number for Models:

CCPP112255EK CCPP11775EK

1 Fuel Tank Assembly

2 Fuel Gauge

3 Fuel Cap

4 Panel Right Side Assembly

5 Power Switch

6 Drain Plug

7 Power Cord

8 Panel Left Side Assembly

9 Ignition Transformer

10 Fuel Filter

11 Combustion Chamber

12 Photocell Bracket

13 Photocell Assembly

14 Burner Head Assembly

14-1 Burner Head

14-2 Nozzle Assembly

14-3 Nozzle Adaptor

572707 572714

572455

---------573414 ----------

572456

572925

---------572251 ----------

572924

----------572450----------

---------573404 ----------

573406

---------573399 ----------

573407

----------572155----------

572706

----------572185----------

572713

----------572186----------

572897 572898

572705 572711

572194

-----------572658-----------

5 72195

14-4 Spark Plug Assembly

15 Fan Guard

16 Fan Assembly

17 Motor and Pump Assembly

17-1 Motor

17-2 Capacitor

17-3

17-4

17-5

17-6

Motor Support

Capacitor Holder

Pump Body

Filter Kit*

17-7 Pump Adjustment Kit***

17-8 Rotor Kit**

17-9 Pump Cover

17-10 Filter Cover

18 Pressure Gauge

19 Main P.C.B. Assembly

20 Air/Fuel Lines

21 Clip Nut (8-Pack)

22 Temperature Limit Assembly

23 Screw (12-Pack)

572704

----------572201----------

572266

572234

572659

572709

-----------572655-----------

---------572703---------

---------572702---------

----------572223----------

----------572227----------

----------572230----------

----------572225----------

---------572696---------

----------572229----------

----------572231----------

-----------573402 -- ---

----------572284----------

572907

572235

572660

572716

572712

24 Upper Shell

25 Lower Shell

Fuse

Hardware Kit

Pump/Filter Cover Screws (10-Pack)

572727

----------572282----------

572933

572710

572708

----------572447----------

-----------572928-----------

----------572283----------

Filter Kit* - Includes Intake, Outlet, and Lint Filter

Rotor Kit** - Include Rotor, Blades, and Insert

Pump Adjustment Kit*** - Includes Ball Spring and Adjusting Screw

572717

572715

24

Parts Identification

PARTS SCHEMATIC (CP210EK)

For Repair Parts, call 1-800-345-7200

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

17-1

17-2

15-4

25

20

15-2

15-1

11

17-4

17-3

17-5

17-6

17-7

17-9

24

12

23

17-8

17-10

1

2

10

14

22

13

15

9

21

16

17

18

8

15-3

19

3

4

5

Figure 29 – Repair Parts Illustration for Portable Oil-Fired Heater (Model CP210EK)

25

6

7

PARTS LIST (CP210EK)

Reference

Number Description

Part Number for Models:

CP210EK

3

4

5

6

1

2

Fuel Tank Assembly

Fuel Gauge

Fuel Cap

Panel Right Side Assembly

Power Switch

Drain Plug

572721

572457

573414

572923

572251

572450

7

8

9

10

11

12

13

14

15

15-1 Nozzle Assembly

15-2 Bracket Burner

15-3 Nozzle Adapter

15-4

16

17

Spark Plug Assembly

Fan Assembly

Motor and Pump Assembly

17-1 Motor

17-2 Motor Support

17-3

Capacitor Holder

17-4 Capacitor

17-5

Pump Body

17-6 Rotor Kit**

17-7 Pump Cover

17-8

Filter Kit*

17-9 Filter Cover

17-10

Pump Adjustment Kit***

18 Pressure Gauge

19

20

21

22

23

24

Fan Guard

Screw (12-Pack)

Main P.C.B. Assembly

Air/Fuel Lines

Clip Nut (8-Pack)

Lower Shell

25

Power Cord

Panel Left Side Assembly

Ignition Transformer

Fuel Filter Assembly

Combustion Chamber

Photocell Bracket

Photocell Assembly

Temperature Limit Assembly

Burner Assembly

Upper Shell

Hardware Kit

Fuse

573404

573407

573399

572155

572720

572185

572186

572725

572899

572196

572719

572662

572202

572235

572661

572723

572703

572702

572655

572224

572226

572696

572227

572229

572230

572231

572267

572282

573402

572718

572284

572722

572724

572928

572447

Pump/Filter Cover Screws (10-Pack) 572283

Filter Kit* - Includes Intake, Outlet, and Lint Filter

Rotor Kit** - Include Rotor, Blades, and Insert

Pump Adjustment Kit*** - Includes Ball Spring and Adjusting Screw

26

27

1

4

5

HARDWARE KIT

Parts Identification

PARTS SCHEMATIC HANDLES & WHEELS

For Repair Parts, call 1-800-345-7200

Please provide following information:

-Model number

-Serial number (if any)

-Part description and number as shown in parts list

2

3

Figure 30– Repair Parts Illustration for Models CP125EK, CP175EK, CP210EK

Replacement Parts List for Models CP125EK, CP175EK, CP210EK

Ref.

No.

3

4

1

2

5

Description

Upper Handle Kit

Wheel Support/Axle Kit

Wheels Kit

Cordwarp Kit

Hardware Kit

Part No. for Models:

CP125EK

572927

572273

576416

572275

572928

CP175EK & CP210EK

572926

572277

Warranty Policy

EQUIPMENT

L.B. White Co., Inc. warrants that the component parts of its heater are free from defects in material and workmanship, when properly installed, operated, and maintained in accordance with the Owner’s Manual safety guides and

24 labels contained with each unit. If, within months from the date of purchase by the end user, any component is found to be defective, L.B. White Co., Inc. will at its option, repair or replace the defective part or heater, with a new part or heater, F.O.B., Onalaska, Wisconsin, USA.

Registering your product online with L.B. White will automatically qualify a unit and its component parts for warranty consideration. If a product has not been registered with L.B.White, a copy of the bill of sale will be required to establish warranty qualification. If neither is available, the warranty period will be 24 months from date of shipment from L.B.White.

PARTS

L.B. White Co., Inc. warrants that replacement parts purchased from the company and used on the appropriate

L. B. White heater are free from defects both in material and workmanship for 24 months from the date of purchase by the end user. Warranty is automatic if a component is found defective within 24 months of the date code marked on the part. If the defect occurs more than 24 months later than the date code but within 24 months from the date of purchase by the end user, a copy of a bill of sale will be required to establish warranty qualification.

The warranty set forth above is the exclusive warranty provided by L.B. White, and all other warranties, including any implied warranties or merchantability or fitness for a particular purpose, are expressly disclaimed. In the event any implied warranty is not hereby effectively disclaimed due to operation of law, such implied warranty is limited in duration to the duration of the applicable warranty stated above. The remedies set forth above are the sole and exclusive remedies available hereunder. L.B. White will not be liable for any incidental or consequential damages directly or indirectly related to the sale, handling or use of the heater, and in any event L.B. White's liability in connection with the heater, including for claims based on negligence or strict liability, is limited to the purchase price.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

To register your product and ensure full warranty, go to http://www.lbwhite.com/product-registration.

Please have the serial number(s) and model(s) handy for the products you are registering.

Replacement Parts and Service

Contact your local L.B. White dealer for replacement parts and service . Y ou may also call L.B White Co., Inc. at (800)345-7200 for assistance or email to [email protected].

Be sure that you have heater model number and configuration number when calling.

28

advertisement

Related manuals

Frequently Answers and Questions

What is the fuel type for the L.B. White CP045DK?
The L.B. White CP045DK uses 1-K, Kerosene as its fuel.
What is the maximum input BTU rating for the L.B. White CP045DK?
The L.B. White CP045DK has a maximum input BTU rating of 45,000 BTU.
What is the fuel consumption per hour for the L.B. White CP045DK?
The L.B. White CP045DK consumes approximately 0.35 gallons of fuel per hour.
What type of motor does the L.B. White CP045DK have?
The L.B. White CP045DK has a 1/8 HP, 3120 RPM ball bearing motor.
What is the electrical supply requirement for the L.B. White CP045DK?
The L.B. White CP045DK requires a 120 volts, 60 hertz, and 1 phase electrical supply.
Is continuous operation allowed with L.B. White CP045DK?
Yes, the L.B. White CP045DK can operate continuously.