Key Innovations ATU Larmöverföringsenhet

Key Innovations ATU Larmöverföringsenhet
Anyway AWU 1020
Anyway Wireless Unit
Output ON or OFF at outgoing alarm
Activate output when sending alarm to other AWU units.
1.
2.
3.
4.
Open menu Sys.prog.
Go to Rly int alarm OFF (or ON)
Press key RIGHT to change function. Display is showing Rly int alarm ON. ON/OFF is alternating when
key RIGHT is pressed.
Press key LEFT to leave
Firmware 2.11.0
User Manual
Automatic reset time at incoming alarm
Select reset time when receiving alarm from external AWU. At reset the display stops flashing and the relay is
released. Other AWU units are not affected by the reset.
1.
2.
3.
4.
Open menu Sys.prog.
Go to Time e alarm 5m
Press key RIGHT to increase reset time. After 30m the value starts again with 5s.
Press key LEFT to leave
Please read this User Manual before using AWU!
Important: Anyway Wireless Unit AWU uses radio signals to communicate and is
designed to reduce influence of interference. At unfavorable conditions the signal
may yet be blocked.
Getting started
Automatic reset time at outgoing alarm
Select reset time when sending alarm to other AWU units. At reset the display stops flashing and the relay is
released. Other AWU units are not affected by the reset.
1.
2.
3.
4.
Open menu Sys.prog.
Go to Time i alarm 5m
Press key RIGHT to increase reset time. After 30m the value starts again with 5s.
Press key LEFT to leave
Firmware version
The firmware version can be read in the menu Sys.prog.
1.
2.
3.
Open menu Sys.prog.
Go to Firmware: X.X.X
Press key LEFT to leave
Input signal MAKE or BREAK
Selects the input to be normally open or normally closed.
Note! The signal connected to the alarm input must have a zero volt potential.
1.
2.
3.
4.
Select whether the unit will extend the range (distance) when repeating ID to other units. Default value is
OFF. Use with caution.
4.
1.
2.
Take the lid off (pull it straight up).
Connect a 9-12V power supply to the power terminal or connect 12 V DC to the screw terminal
according to the picture below.
The AWU will find other units within a couple of minutes.
At delivery, the AWU has an identity consisting of four characters – two letters and two digits. It’s convenient
to change the identity to something in plain language. See instruction below.
Connections and keys
At the front of the AWU there is a display, four keys for setup purposes and one key to activate the alarm.
Connections for power and signal I/O are located under the lid. The lid must be removed to reach the
connections.
Power may be connected to the 2.1mm DC connector or to the screw terminal according to the picture below.
Cables may be secured with a cable strap around the “T”-shape on the circuit board.
Open menu Sys.prog.
Go to Alarm input MAKE (MAKE = normally open)
Press key RIGHT to change function. The display is showing Alarm input BRAKE (BRAKE = normally
closed). MAKE/BRAKE is alternating when key RIGHT is pressed.
Press key LEFT to leave
Extended range repeater mode ON or OFF
1.
2.
3.
It’s easy to get started with AWU:
Open menu Sys.prog.
Go to Extend range OFF
Press key RIGHT to change function. Display is showing Extend range ON. ON/OFF is alternating when
key RIGHT is pressed.
Press key LEFT to leave
Alarm Input
DC connector
(9-12V)
+ (9-12V)
–
Input (MAKE or
Input BREAK)
(potential free)
Relay output:
Distributor:
Common
Normally closed
Normally open
WIRELESS COMMUNICATIONS
www.anyway.se
The AWU can be activated by external
equipment, such as the central unit of a burglar
alarm or a button or a magnetic door switch. The
signal can be either MAKE or BREAK. MAKE is
the default setup. This can be changed in
Sys.prog.
Note! The signal connected to the alarm input
must be potential free, i e no external voltage
source.
Alarm Output
The AWU has a built-in relay that can be used to
activate external equipment when the AWU
receives and/or sends an alarm. This can be
changed in Sys.prog. The output can be
connected as normally open or normally closed
according to the picture.
Keys
Change group - CHANGE GROUP OF ALL CONNECTED AWU 1020/1310
LEFT – Used to move the cursor left when entering text and also used to undo.
RIGHT - Used to move the cursor right when entering text and also used to commit.
Each unit belongs to a group. The unit can only communicate with other units belonging to the same group.
The group identity consists of 3 characters and can be changed. The default group identity is AA0. There are
more than 6000 possible group identities.
DOWN - Used to step down in the menu and step down character value when entering text.
1.
UP – Used to step up in the menu and step up character value when entering text.
ALARM KEY – Used to activate an alarm. Same function as the alarm input.
Usage
The AWU unit is used to receive, send and retransmit alarm signals and identities throughout the network.
Incoming alarm
When an incoming alarm from another AWU is received, the buzzer sounds and the display shows the name
of the other AWU.
1.
Press any key to silent the buzzer
2.
Scroll incoming alarm´s AWU name with keys DOWN and UP
3.
Press key LEFT to reset display
If no key is pressed, the AWU will reset automatically after the preset time – see System programming.
2.
3.
4.
5.
Open menu Change group. The current group is shown in the display and the cursor is at first
character.
Use keys DOWN and UP to change the character
Use keys RIGHT and LEFT to move the cursor between character positions
When the group is changed, move the cursor past the rightmost position with key RIGHT. The display is
showing New group stored!!
Press key LEFT to leave
NOTE: STUDY THE USER MANUAL FOR PROGRAMMING REMOTE UNIT AWU 1310
Connection test
1.
Open menu Alarm testing.
2.
Press key RIGHT to activate the connection test. The display is showing Test alarm sent.
3.
The display will show Test alarm OK if the unit is able to recognize any other unit.
4.
Press key LEFT to leave
The other units will show -=TEST ALARM=-. The buzzer is silent.
System programming (Sys.prog.)
Outgoing alarm
To send an alarm you can either press the ALARM KEY or activate the alarm input on the screw terminal. The
input can be normally closed or normally open – see System programming.
1.
When activated, the display is showing INTERNAL ALARM
2.
Press key LEFT to reset
In the System programming menu, the following functions may be altered:










If no key is pressed, the AWU will reset automatically after the preset time – see System programming.
General setup
The AWU unit can be implemented for many applications without any need for setup. However, the following
parameters can be changed in the setup menu:






The menu:
1.
2.
3.
4.
Name
Group
Sound buzzer
In- and output
Time for automatic reset
Extended range repeater mode
Open the main menu by pressing keys LEFT and RIGHT simultaneously
Scroll the menu with keys DOWN and UP
Open a menu line with key RIGHT
Press key LEFT to leave
Change name
Sound ON/OFF at incoming alarm
Sound ON/OFF at outgoing alarm
Relay Output ON/OFF at incoming alarm
Relay Output ON/OFF at outgoing alarm
Time for automatic reset at incoming alarm
Time for automatic reset at outgoing alarm
Firmware version
Input MAKE/BREAK
Extended range repeater mode ON/OFF
Programming Remote unit (see Manual AWU 1310)
Sound ON or OFF at incoming alarm
Activate the built in buzzer when receiving alarm from external AWU.
Open menu Sys.prog. The display is showing Snd ext alarm ON (or OFF)
1.
2.
Press key RIGHT to change function. The display is showing Snd ext alarm OFF. ON/OFF is alternating
when key RIGHT is pressed.
Press key LEFT to leave
Sound ON or OFF at outgoing alarm
Activate the built in buzzer when sending alarm to other AWU units.
1.
2.
3.
Open menu Sys.prog.
Go to Snd int alarm OFF (or ON)
Press key RIGHT to change function. The display is showing Snd int alarm ON. ON/OFF is alternating
when key RIGHT is pressed.
Press key LEFT to leave
Each AWU unit has a unique, factory set identity. This identity may be changed to anything consisting of not
more than 16 alphanumeric characters.
4.
1.
Activate output when receiving alarm from external AWU.
2.
3.
4.
5.
Open menu Change name. The current name is shown in the display and the cursor is at first
character.
Use keys DOWN and UP to change the character
Use keys RIGHT and LEFT to move the cursor between character positions
When the name is changed, move the cursor past the rightmost position with key RIGHT. The display is
showing Name stored!
Press key LEFT to leave
Output ON or OFF at incoming alarm
1.
2.
3.
4.
Open menu Sys.prog.
Go to Rly ext alarm OFF (or ON)
Press key RIGHT to change function. Display is showing Rly ext alarm ON. ON/OFF is alternating when
key RIGHT is pressed.
Press key LEFT to leave
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement