ESIM264 - Induo Wireless
GSM ALARM AND MANAGEMENT SYSTEM
USER MANUAL
ESIM264
COMPLIES WITH EN 50131-1 GRADE 2, CLASS II REQUIREMENTS
User Manual v2.1
Valid for ESIM264 v7.11.18 and up
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• GSM alarm & management system ESIM264 (also referenced as alarm system, system or device) has radio transceiver operat­
ing in GSM 850/900/1800/1900 bands.
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
• System label is on the bottom side of the device.
GSM alarm system ESIM264 is a device mounted in limited access areas. Any system repairs must be done only by quali­
fied, safety aware personnel.
The system must be powered by main 16-24V 50 Hz ~1.5A max or 18-24V
1,5A max DC power supply which must
be approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply
to the system, switching the pole terminals places does not have any affect.
Any additional devices linked to the system ESIM264 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
Main power supply can be connected to AC mains only inside installation room with
automatic 2-pole circuit breaker capable of disconnecting circuit in the event of short
circuit or over-current condition. Open circuit breaker must have a gap between con­
nections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
ESIM364
USB cable
Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installa­
tion or maintenance must not be done during stormy conditions.
Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one
of battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching
the pole terminals places is NOT allowed.
In order to avoid fire or explosion hazards the system must be used only with approved backup battery.
The device is fully turned off by disconnecting 2-pole switch off device of the main power supply and disconnecting
backup battery connector.
Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the
product must not be disposed of together with household waste. To prevent possible harm to human health and/or the environ­
ment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how
to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal in your area.
Limited Liability
The buyer must agree that the system will reduce
the risk of fire, theft, burglary or other dangers but
does not guarantee against
such events.
“ELDES UAB” will not take any responsibility re­
garding personal or property or revenue loss
while using the system. “ELDES UAB” liability ac­
cording to local laws does not exceed value of the
purchased system. “ELDES UAB” is not affiliated
with any of the cellular providers therefore is not
responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the
manufacturer “ELDES UAB”. Warranty period starts
from the day the system has been purchased
by the end user. The warranty is valid only if the
system has been used as intended, following all
guidelines listed in the manual and within speci­
fied operating conditions. Receipt must be kept as
a proof of purchase date.
The warranty is voided if the system has been
exposed to mechanical impact, chemicals, high
humidity, fluids, corrosive and hazardous environ­
ments or other force majeure factors.
Technical Support
If you require more detailed information on your
system or in case of system failure occurrence,
please, contact your alarm system installer.
About User Manual
This document describes basic configuration and
usage of alarm system ESIM264. It is very impor­
tant to read the user manual before starting to use
the system.
Package Content
Contents
1. General Information...................................................................... 4
1.1 1.2 1.3 1.4 Short Description of Main Definitions................................................4
EKB2 Keyboard Overview........................................................................5
EKB3 Keyboard Overview........................................................................7
Partitions.......................................................................................................7
2. Technical Specifications................................................................ 8
2.1 2.2 2.3 Electrical & Mechanical Characteristics..............................................8
Main Unit, LED & Connector Functionality.......................................9
Wiring Diagrams...................................................................................... 10
2.3.1 General Wiring.......................................................................... 10
2.3.2 Zone Connection Types......................................................... 10
3. Basic Configuration & Use...........................................................11
3.1 Setting Up Date & Time......................................................................... 11
3.2. Arming, Disarming the System & Turning Off the Alarm.......... 12
3.2.1 Arm, Disarm & Turn off the Alarm by Phone Call.......... 12
3.2.2 Arm by SMS Message............................................................. 13
3.2.3 Disarm & Turn off the Alarm by SMS Message.............. 13
3.2.4 Arm by EKB2/EKB3 Keyboard.............................................. 14
3.2.5 Disarm & Turn off the Alarm by EKB2/EKB3 Keyboard.14
3.2.6 Arm by iButton® Key............................................................... 15
3.2.7 Disarm & Turn off the Alarm by iButton® Key................ 15
3.2.8 Arm by EWK1 – Wireless Key-fob........................................ 16
3.2.9 Disarm & Turn off the
Alarm by EWK1 – Wireless Key-fob.................................... 16
3.3 Activating STAY Mode........................................................................... 17
3.3.1 Arm by EKB2 Keyboard in STAY Mode Manually.......... 17
3.4 Alarm Indications & Viewing Violated Zones / Tampers............ 19
3.5 Bypassing & Unbypassing Violated Zone....................................... 20
3.6 Viewing System Information............................................................... 21
3.7 Managing Periodical System Information...................................... 21
3.8 Viewing Zone & PGM Output Information..................................... 22
3.9 Managing Temperature Information............................................... 23
3.10 Trouble Indications................................................................................. 24
3.11 Controlling Electrical Appliances...................................................... 25
3.12 Turning ON/OFF the Electrical
Appliances for a Determined Time Period..................................... 26
4. If the Alarm System is Connected to Monitoring Station.........27
1. ESIM264................................................. qty. 1
2. Microphone.......................................... qty. 1
3. SMA antenna....................................... qty. 1
4. Backup battery connection wire.qty. 1
5. User manual......................................... qty. 1
6. Resistor 5,6kΩ...................................... qty. 6
7. Resistor 3,3kΩ...................................... qty. 6
NOTE: For full system configuration and control,
please refer to ESIM264 installation manual lo­
cated at www.eldes.lt/en/download
Copyright © “ELDES UAB”, 2012. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization
by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby,
“ELDES UAB” declares that this GSM alarm and management system ESIM264 is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
1. General Information
ESIM264 is an alarm system for private houses, cottages, village houses, garages, warehouses and other buildings, also capable of
turning on/off the electrical appliances by SMS message and alarm system keyboard. This alarm system provides a simple thus effec­
tive way of use.
The system consists of:
• ESIM264 alarm system device;
• Up to 4 EKB2/EKB3 keyboards;
• Wired and/or wireless sensors: movement sensors, magnetic door sensors, smoke sensors etc.;
• Other devices: indoor/outdoor sirens, heating, lighting, gates etc.
For more details on ESIM264 system, please, consult with your alarm system installer.
1.1 Short Description of Main Definitions
The following table provides the explanation of main definitions which are met in this user manual.
Definition
Description
System; alarm system
ESIM264 device
SMS
Short Message Service text
Keyboard
Device with a set keys allowing to configure & control the system, view violated zones & system troubles
EKB2
Model of LCD keyboard
EKB3
Model of LED keyboard
User phone number; User 1... 5 Phone number of the user allowed to control the system
System phone number
Phone number of the SIM card inserted in ESIM264 device
User password
4-digit combination intended for system arming/disarming using a keyboard
iButton® key
Small metal tab containing a unique ID code intended for system arming/disarming
Zone
Alarm system input for wired and wireless sensor connection
PGM output
Alarm system output for connection of electrical appliances (heating, lighting, gates etc.)
Partition
Section dividing one alarm system into two independent parts software-wise
4
1.2 EKB2 Keyboard Overview
EKB2 is an LCD keyboard intended for using with ESIM264 alarm system.
Temperature
Keys Functionality
One menu level back / cancel
GSM Signal
Strength
Digital Clock
20,20C
Menu navigation – up
System Status
Message
Menu navigation – down
Confirm (enter) value
...
Value typing
Keyboard partition switch / minus
symbol for entering negative
temp. value
STAY
BYP
TBL
00:45
ready
GARAGE
Main Screen
View
Bypass Mode
Indication
System
Trouble
Indication
Stay Mode
Indication
Custom
Keyboard
Partition
Title
Additional menu / minus symbol
for entering negative temp. value
Fig. No. 1
Main Messages & Icons
Icon / Message
Description
Delay zone violated when system is disarmed.
Exit Delay countdown initiated.
System is armed and menu is locked.
System is disarmed and menu is unlocked
Icon / Message
24H zone violated.
FIRE ALARM
Fire zone violated.
TAMPER ALARM
READY
NOT READY
ARMED
+ CONFIGURATION
MODE
BURGLARY ALARM
Configuration mode activated.
Delay, Instant or Follow zone violated when
system is armed.
MANUAL ELDES ESIM264 V2.1
Description
24 ALARM
Tamper violated
System is ready to be armed.
System is not ready to be armed – one or more
zones / tampers violated.
System is armed (optional feature).
STAY
Stay mode activated
BYP
One or more zones bypassed
TBL
One or more system troubles are present
5
EKB2 LCD screen is intended for displaying alarm system status messages and alerts. Message READY is displayed on the screen that
no zones are violated or no troubles are present and the system is prepared for arming. Message NOT READY (and TBL) shows up in
case of zone violation or if system troubles are present. The alarm system cannot be armed until the troubles are removed or violated
zone (-s) is restored, bypassed or set up to operate under Force mode. The following troubles allow system arming when present:
•
backup battery problem;
•
main power supply failure;
•
date & time not set;
•
GSM connection problem.
Audio Indication
The built-in mini buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for success­
fully carried out configuration, one long beep – for invalid configuration. In addition, the mini-buzzer continuously provides short
beeps in case of alarm.
Visual Indication
EKB2 can be used even in dark premises as the LCD screen and keys are illuminated continuously. In case of alarm the keyboard il­
lumination level is boosted and stays in this state until the system is disarmed. The illumination level lowers down in 3 minutes after
the last key-touch while the system is disarmed.
6
1.3 EKB3 Keyboard Overview
EKB3 is a LED keyboard intended for using with ESIM264 alarm system.
LED Functionality
ARMED
Alarm system is armed /Configuration mode
READY
System is prepared for arming
SYSTEM
System troubles / valid command is being entered
BYPS
Zone bypass mode
1-12
Violated zone
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
5
6
10
11
12
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
Fig. No. 2
Keys Functionality
[BYPS]
Zone bypass mode
[CODE]
Additional options - system trouble list / violated high zone indication / violated tamper indication
[*]
Configuration mode (when typed as a 1st character) / cancel command (when typed as a 2nd character) / keyboard
partition switch (if enabled)
[#]
Confirm (enter) command
[0] ... [9]
Command typing
[STAY]
Manual Stay mode activation
[INST]
(currently inactive)
The green LED READY indicates that no zones are violated or no troubles are present and the system is prepared for arming. LED
SYSTEM lights up or flashes in case of zone violation or if system troubles are present. The alarm system cannot be armed until the
troubles are removed or violated zone (-s) is restored, bypassed or set up to operate under Force mode. The following troubles allow
system arming when present:
•
backup battery problem;
•
main power supply failure;
•
date & time not set;
•
GSM connection problem.
Audio Indication
The built-in mini buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for success­
fully carried out configuration command, one long beep – for invalid configuration command. In addition, the mini-buzzer continu­
ously provides short beeps in case of alarm.
Visual Indication
EKB3 keys have a LED back-light, therefore it is possible to use this keyboard even in dark premises. In case of alarm the keyboard
back-light turns on and lasts until the system is disarmed. The back-light lasts for 3 minutes after the last key-stroke while the system
is disarmed.
1.4 Partitions
Your alarm system may be divided into 2 partitions: partition 0 & partition 1. Each system partition operates independently from each
other, therefore dividing the system into partitions allows to use 1 alarm system unit to secure 2 different areas, for example: office
and warehouse, house and garage. By default configuration, the system is NOT divided into 2 partitions and all user phone numbers,
user passwords, keyboards, iButton® keys, zones are assigned to partition 0.
MANUAL ELDES ESIM264 V2.1
7
2. Technical Specifications
2.1 Electrical & Mechanical Characteristics
Electrical & Mechanical Characteristics
Main Power Supply
Current in Standby without External Sensors and Keyboard
Recommended Backup Battery Voltage, Capacity
Recommended Backup Battery Type
Maximum Battery Charge Current
GSM Modem Frequency
Cable Type for GSM/GPRS Antenna Connection
Number of Zones on Board
Nominal Zone Resistance
Number of PGM Outputs on Board
PGM Output C1-C4 Circuit
16-24V 50 Hz ~1.5A max / 18-24V
Up to 80mA
12V; 1,3-7Ah
Lead-Acid
900mA
850/900/1800/1900MHz
Shielded
6 (ATZ mode: 12)
5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ)
4
Maximum Commuting PGM Output Values
BELL: Siren Output when Activated
BELL: Maximum Siren Output Current
BELL: Maximum Cable Length for Siren Connection
BELL: Cable Type for Siren Connection
AUX: Auxiliary Equipment Power Supply Voltage
AUX/BELL: Maximum Accumulative Current of Auxiliary Equip­
ment and Siren
AUX: Maximum Cable Length for Auxiliary Equipment Connection
AUX: Cable Type for Auxiliary Equipment Connection
BUZ: Maximum Current of Mini Buzzer
BUZ: Power Supply Voltage of Mini Buzzer
BUZ: Cable Type for Mini Buzzer Connection
Dimensions
Operating Temperature Range
Supported Temperature Sensor Model
DATA: Maximum Cable Length for 1-Wire® Communication
DATA: Cable Type for 1-Wire® Communication
Supported iButton® Key Model
Maximum Supported Number of Keyboards
Y/G: Maximum Cable Length for RS485 Communication
Y/G: Cable Type for RS485 Communication
MIC: Maximum Cable Length for Microphone Connection
MIC: Cable Type for Microphone Connection
Voltage – 30V; Current – 100mA;
Connected to COM
500mA
up to 30 meters
Unshielded
13,8V DC
1A
Wireless Transmitter-Receiver Frequency *
868 Mhz
Wireless Communication Range*
Maximum Supported Number of Wireless Devices*
Event Log Size
Maximum Supported Number of Zones
Maximum Supported Number of PGM Outputs
Cable Type for Zone and PGM Output Connection
Communications
Supported Protocols
Up to 30m in premises; up to 150m in open areas
16
500 events
44
44
Unshielded
SMS, Voice calls. GPRS network, RS485, CSD
Ademco Contact ID®, 4+2, EGR100, Kronos
* only for system ESIM264 with module EWT1
8
1R
OUT
1,5A max
Open Collector Output.
Output is pulled to COM
when turned ON.
up to 100 meters
Unshielded
150mA
5V DC
Unshielded
140x100x18mm
-20...+550C
Maxim®/Dallas® DS18S20, DS18B20
up to 30 meters
Unshielded
Maxim®/Dallas® DS1990A
4 x EKB2 / EKB3
up to 100 meters
Unshielded
Up to 2 meters
Unshielded
2.2 Main Unit, LED & Connector Functionality
STATUS
PWR
Z6
Z5
Z4
Z3
Z2
Z1
C1
C2
NETWORK
Main Unit Functionality
GSM network 850/900/1800/1900MHz
modem
SIM CARD
SIM card slot / holder
DEF
Pins for restoring default settings
USB
Mini USB port
FUSE F1
3A fuse
C4
C3
ANTENNA
SMA
SIM
CARD
GSM
MODEM
DEF
3A
PRG
ANTENNA
GSM/GPRS antenna SMA type con­
nector
MODULES
Slots for EA1, EA2 or EPGM8 module
EWT1
Slots for EWT1 wireless module
FUSE F1
GSM MODEM
EWT1
MODULES
USB
AKU+
AKU-
AC/DC
AC/DC
AUX+
AUXBELL+
BELLCOM
G
Y
C2
C1
BUZ+
BUZMIC+
MIC+5V
DATA
COM
Z6
COM
Z5
Z4
COM
Z3
Z2
COM
Z1
LED Functionality
NETWORK GSM network signal strength
Fig. No.3
C2, C1
PGM output C1, C2 status – on/off
Z1
Zone Z1 state – alarm/restore (ATZ mode: Z1 and Z7)
Z2
Zone Z2 state – alarm/restore (ATZ mode: Z2 and Z8)
Z3
Zone Z3 state – alarm/restore (ATZ mode: Z3 and Z9)
Z4
Zone Z4 state – alarm/restore (ATZ mode: Z4 and Z10)
Z5
Zone Z5 state – alarm/restore (ATZ mode: Z5 and Z11)
Z6
Zone Z6 state – alarm/restore (ATZ mode: Z6 and Z12)
PWR
Power supply status
STATUS
Micro-controller status
Connector Functionality
Z1 - Z6
Security zones
COM
Common terminal for all zones
DATA
1-Wire® interface for iButton® key & temperature sensor connection
+5V
Temperature sensor power supply contact (+5V)
MIC-
Microphone negative terminal
MIC+
Microphone positive terminal
BUZ-
Mini buzzer negative terminal
BUZ+
Mini buzzer positive terminal
C1 - C4
PGM outputs
Y
RS485 interface for communication (yellow wire)
G
RS485 interface for communication (green wire)
COM
Common return terminal
BELL-
Siren negative terminal
BELL+
Siren positive terminal
AUX-
Negative power supply terminal for auxiliary equipment
AUX+
Positive power supply terminal for auxiliary equipment
AC/DC
Main power supply terminal
AKU-
Backup battery negative terminal
AKU+
Backup battery positive terminal
MANUAL ELDES ESIM264 V2.1
9
2.3 Wiring Diagrams
2.3.1 General Wiring
AKU+
AKU-
Резервная
Батарея
12В 1.3-7Ач
AC/DC
AC/DC
AUX+
AUXBELL+
BELLCOM
G
Y
C2
C1
BUZ+
BUZMIC+
MIC+5V
DATA
COM
Z6
COM
Z5
Z4
COM
Z3
Z2
COM
Z1
PE контакт
металической
коробки
Fuse 500 mA
~16-24В
Z6
5.6k
5.6k
5.6k
5.6k
5.6k
Z5
Z4
Z3
Z2
Z1
MIC
Сирена
Fig. No. 4
~230V 50Гц
BUZ
EPGM1
500 мА макс.
iButton®
key reader
Модуль
реле
EKB3
Температурный сенсор
EKB2
2.3.2 Zone Connection Types
Type 1
Normally open contact
with 5,6KΩ end of line
resistor
Fig. No. 5
10
Type 2
Normally closed con­
tact with 5,6KΩ end of
line resistor
Type 3
Tamper and 5,6KΩ
end of line resistor
and 3,3KΩ end of line
resistor with normally
closed contact
Type 4
Type 5
ATZ Mode: 5,6KΩ end
of line resistor and nor­
mally closed contact
with 3,3KΩ end of line
resistor and normally
closed contact
ATZ Mode: Tamper,
5,6KΩ end of line
resistor, 5,6KΩ end of
line resistor with nor­
mally closed contact
and 3,3KΩ end of line
resistor with normally
closed contact.
3. Basic Configuration & Use
ATTENTION: System configuration described in this chapter is based on default system parameter values. Your alarm system
installer may have changed those values. For more details, please, contact your alarm system installer.
This chapter provides a description of basic configuration and use of ESIM264 alarm system by the following methods:
•
SMS message;
•
Phone call;
•
EKB2 keyboard;
•
EKB3 keyboard;
•
iButton® key.
SMS
EKB2
EKB3
In order to configure and control the system using SMS message, send the text command to the ESIM264 system phone
number from one of the preset user phone numbers. In this user manual the underscore symbol ”_” represents one space
character. Every underscore symbol must be re­placed by a single space character. There must be no spaces or other un­
necesary characters at the beginning and at the end of the message. XXXX – 4-digit SMS password set by your alarm
system installer.
The system configuration and control by EKB2 keyboard is performed by navigating throughout the menu section list dis­
played on LCD screen. To navigate in the menu path, touch ↓, ↑ keys to select the desired menu section and touch OK key
to open the selected section. To enter a required value, use 0... 9 keys and touch OK key for value confirmation or cancel/
go one menu section back by touching ←key. The value can be typed in directly by touching 0... 9 keys while highlighting
the desired menu section. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will
be brought back to the beginning of the list after touching the ↓ key. In this user manual, the menu path is provided under
“tree” view by starting at main screen view. In this user manual valid parameter values and range are indicated in brackets.
The system configuration and control by EKB3 keyboard is performed by entering a valid configuration command using
the number keys 0... 9 and [#] key for confirmation. Some commands require [BYPS], [CODE] and [STAY] keys as well. The
structure of standard configuration command is a combination of digits. In this user manual configuration commands,
valid param­eter values and range are indicated in brackets.
3.1 Setting Up Date & Time
NOTE: When the alarm system is connected to a monitoring station the date and time are set automatically. The system retrie­
ves this data from the monitoring station by itself.
SMS
1. Send the following SMS message to the phone number of ESIM264 alarm system:
SMS text:
XXXX_YYYY.MM.DD_HR:MN
Value: YYYY– year; MM – month, range – [01... 12]; DD – day, range - [01... 31];
HR – hours, range – [00... 23], MN – minutes, range – [00... 59];
Example: 1111_2011.12.15_13:45
2. The system will reply with confirmation by SMS message to user phone number who sent the SMS message
after the date & time is set successfully.
EKB2
Navigate through the following menu path using OK and arrow keys and
enter the date and time values using the number keys:
Menu path:
OK → DATE/TIME SET → [YYYY-MM-DD_HR:MN]
Value: YYYY– year; MM – month, range – [01... 12]; DD – day, range - [01... 31];
HR – hours, range – [00... 23], MN – minutes, range – [00... 59];
Example: 2011-12-15 13:45
MANUAL ELDES ESIM264 V2.1
11
3.2. Arming, Disarming the System & Turning Off the Alarm
Before arming the system it is necessary to close all doors and windows in the secured area and move yourself away from the move­
ment detection field.
Don’t stand in
movement sensor
detection zone
Close all
doors
Close all
windows
Close all
doors
Fig. No. 6
3.2.1 Arm, Disarm & Turn off the Alarm by Phone Call
ATTENTION: User must leave the secured area before arming the system by phone call.
1. To arm the system, disarm the system or turn off the alarm, make a phone call to the system‘s phone number
from any out of 5 preset user phone numbers. The phone call is free charge as the system rejects it and performs
arming or disarming after-wards. When arming the system, it rejects the phone call after 2 rings, when disarming
- the system rejects the phone call immediately.
2. After the system is successfully armed or disarmed, it will reply with confirmation by SMS message to the user
phone number who made a phone call.
CALL
SMS
User
ESIM264
Fig. No. 7
3. When attempting to arm the system in case of violated zone / tamper presence, the system will reply with vio­
lated zone / tamper number. For more details, please refer to chapter 2.5 Bypassing & Unbypassing Violated
Zone.
12
3.2.2 Arm by SMS Message
SMS
1. Leave the secured area.
2. To arm the system, send the following SMS message to the system‘s phone number from any out of 5 preset user
phone numbers:
SMS text:
XXXX_ARM1 or XXXX_ARM2 or XXXX_ARM1,2
Value: 1 – partition 0; 2 – partition 1; 1,2 – both partitions
Example: 1111_ARM1
3. After the system is successfully armed, it will reply with confirmation by SMS message to the user phone number
who sent the SMS message.
SMS
SMS
User
ESIM264
Fig. No. 8
4. When attempting to arm the system in case of violated zone / tamper presence, the system will reply with vio­
lated zone / tamper number. For more details, please refer to chapter 2.5 Bypassing & Unbypassing Violated
Zone.
3.2.3 Disarm & Turn off the Alarm by SMS Message
SMS
1. The system will initiate the Entry Delay countdown (by default – 15 seconds) after the user has entered the
secured area. Entry Delay countdown is intended for user to enter a valid user password before the alarm is
caused.
2. To disarm the system or turn off the alarm, send the following SMS message to the system‘s phone number
from any out of 5 preset user phone numbers:
SMS text:
XXXX_DISARM1 or XXXX_DISARM2 or XXXX_DISARM1,2
Value: 1 – partition 0; 2 – partition 1; 1,2 – both partitions
Example: 1111_DISARM1
3. After the system is successfully disarmed, it will reply with confirmation by SMS message to the user phone
number who sent the SMS message.
SMS
SMS
User
MANUAL ELDES ESIM264 V2.1
ESIM264
Fig. No. 9
13
3.2.4 Arm by EKB2/EKB3 Keyboard
EKB2
EKB3
1. To arm the system, enter any out of 10 available 4-digit user passwords using the number keys:
1
2
3
4
5
6
7
8
9
0
Fig. No. 10
Enter user password:
[NNNN]
Value: NNNN – 4-digit user password
EKB2 Example: 1111OK
EKB3 Example: 1111
2. The system will initiate the Exit Delay countdown (by default – 15 seconds) intended for user to leave the secu­
red area. The countdown is indicated by short beeps provided by keyboard built-in mini-buzzer (if any).
3. After the system is successfully armed, it will reply with confirmation by SMS message to User 1 phone number
(by default).
SMS
User
ESIM264
Fig. No. 11
3.2.5 Disarm & Turn off the Alarm by EKB2/EKB3 Keyboard
EKB2
1. The system will initiate the Entry Delay countdown (by default – 15 seconds) after the user has entered the
secured area. Entry Delay countdown is intended for user to enter a valid user password before the alarm is
caused.
EKB3
2. To disarm the system or turn off the alarm, enter any out of 10 available 4-digit user passwords using the num­
ber keys:
1
2
3
4
5
6
7
8
9
0
Fig. No. 12
Enter user password:
[NNNN]
Value: NNNN – 4-digit user password
EKB2 Example: 1111OK
EKB3 Example: 1111
3. After the system is successfully disarmed, it will reply with confirmation by SMS message to User 1 phone
number (by default).
SMS
User
14
ESIM264
Fig. No. 13
3.2.6 Arm by iButton® Key
1. To arm the system, touch the iButton® key reader by any out of 5 iButton® keys:
Fig. No. 14
2. The system will initiate the Exit Delay countdown (by default – 15 seconds) intended for user to leave the secu­
red area. The countdown is indicated by short beeps provided by ESIM264 mini-buzzer (if any).
3. After the system is successfully armed, it will reply with confirmation by SMS message to User 1 phone number
(by default).
SMS
User
ESIM264
Fig. No. 15
3.2.7 Disarm & Turn off the Alarm by iButton® Key
1. The system will initiate the Entry Delay countdown (by default – 15 seconds) after the user has entered the
secured area. Entry Delay countdown is intended for user to enter a valid user password before the alarm is
caused.
2. To disarm the system or turn off the alarm, touch the iButton® key reader by any out of 5 iButton® keys:
Fig. No. 16
3. After the system is successfully disarmed, it will reply with confirmation by SMS message to User 1 phone num­
ber (by default).
SMS
User
MANUAL ELDES ESIM264 V2.1
ESIM264
Fig. No. 17
15
3.2.8 Arm by EWK1 – Wireless Key-fob
EWK1
1. To arm the system, press 1 out of 4 EWK1 buttons (by default –
button) assigned to arm the alarm system.
Arm the
system
Fig. No. 18
2. The system will initiate the Exit Delay countdown (by default – 15 seconds) intended for user to leave the secured area.
3. After the system is successfully armed, it will reply with confirmation by SMS message to User 1 phone number (by
default).
SMS
User
ESIM264
Fig. No. 19
3.2.9 Disarm & Turn off the Alarm by EWK1 – Wireless Key-fob
EWK1
1. The system will initiate the Entry Delay countdown (by default – 15 seconds) after the user has entered the secu­
red area. Entry Delay countdown is intended for user to enter a valid user password before the alarm is caused.
2. To disarm the system or turn off the alarm, press 1 out of 4 EWK1 buttons (by default –
disarm the alarm system
button) assigned to
Disarm the
system
Fig. No. 20
3. After the system is successfully disarmed, it will reply with confirmation by SMS message to User 1 phone
number (by default).
SMS
User
16
ESIM264
Fig. No. 21
3.3 Activating STAY Mode
EKB2
EKB3
EWK1
Stay mode allows the user to remain in the secured area after arming the system. In Stay mode, the system does not
cause the alarm when the zones, set up to operate under this mode, become violated. This mode is usually used
when arming the system before night.
There are two ways to activate Stay mode:
•
Automatic - This mode is activated automatically in case the user does not leave the secured area (if Delay
zone is not violated) during Exit Delay countdown when arming the system.
•
Manual - The system goes into Stay mode after the user opens an additional menu or presses [STAY] key and
enters a valid user password by EKB2/EKB3 keyboard.
There is no Exit Delay countdown when activating Stay mode manually.
Stay mode status is indicated in the main screen view of EKB2.
Stay mode is NOT activated when arming the system by phone call or SMS message.
NOTE: Delay Zone Becomes Instant in Stay Mode feature may be enabled on your system. In that case the alarm will be
caused instantly instead of Entry Delay countdown being initiated if a Delay zone becomes violated while the system
is operating in Stay mode. For more details, please, contact your alarm system installer.
3.3.1 Arm by EKB2 Keyboard in STAY Mode Manually
EKB2
1. Navigate through the following menu path using P2 and arrow keys and enter a valid user password using the
number keys to arm the system in Stay mode manually:
Menu path:
P2 → ENTER STAY → [NNNN] → OK
Value: [NNNN] - 4-digit user password
2. After the system is successfully armed, it will reply with confirmation by SMS message to User 1 phone number
(by default).
SMS
User
ESIM264
For more details on how to disarm & turn off the alarm by EKB2 keyboard, please refer to chapter 3.2.5 Disarm & Turn
off the Alarm by EKB2/EKB3 Keyboard
MANUAL ELDES ESIM264 V2.1
17
3.3.2 Arm by EKB3 Keyboard in STAY Mode Manually
EKB3
1. Arm the system in Stay mode manually by entering the following combination using [STAY] and number keys:
Press [STAY] key & enter user password:
[STAYnnnn]
Value: nnnn - 4-digit user password
Example: STAY1111
2. After the system is successfully armed, it will reply with confirmation by SMS message to User 1 phone number
(by default).
SMS
User
ESIM264
For more details on how to disarm & turn off the alarm by EKB3 keyboard, please refer to chapter 3.2.5 Disarm & Turn
off the Alarm by EKB2/EKB3 Keyboard
18
3.4 Alarm Indications & Viewing Violated Zones / Tampers
By default configuration, the system makes a phone call to User 1 in case of alarm. By answering the call, the user is
able to listen on his/her mobile phone to what is happening in area surrounding ESIM264 unit. This feature is pro­
vided by a microphone (if any) connected to ESIM264.
The phone call is made to the next preset user (presumably to User 2) in a row in case the previous user was unreach­
able (was “out of radio coverage”, provided “busy” signal or did not answer the call). This routine is continued until one
of the preset users is reachable, but will not go in a circle i. e. return to User 1 if none of the users were reachable. In
addition, the system will not make a phone call to the next preset user in a row if the previous user was reachable, but
rejected the phone call. The phone calls will cease to be made to the user as soon as the system is disarmed.
CALL
User
ESIM264
Fig. No. 22
NOTE: Your alarm system installer may have configured the system to make the phone calls to the next available user even if the
previous one has answered the call.
SMS
By, default configuration the system sends an SMS message containing violated zone or tamper number in case of
alarm. The SMS message can also contain a star * character next to the violated tamper in case the tamper violation is
caused due to wireless connection loss between ESIM264 and a wireless device (if any).
This SMS message is sent to User 1. The system sends the SMS message to the next preset user (presumably to User
2) in a row only if the previous user was unreachable (the system did not receive a successful SMS message delivery
confirmation in 20 seconds from the recipient). This routine is continued until one of the preset users is reach­able, but
will not go in a circle i. e. return to User 1 if none of the users were reachable. The SMS messages will cease to be sent
to the user as soon as the system is disarmed.
SMS
User
ESIM264
Fig. No. 23
See also chapter 2.6 Viewing System Information.
NOTE: Your alarm system installer may have configured the system to send the SMS message to the next available user even if
the previous one has received it.
MANUAL ELDES ESIM264 V2.1
19
EKB2
EKB3
The built-in EKB2 mini-buzzer and ESIM264 mini-buzzer (if any) provide short beeps continuously in case of alarm.
In addition, the LCD screen back-light level is boosted and the alarm message (depending on violated zone type or
tamper violation) is displayed in the main screen view of EKB2 screen. The mini-buzzer can be silenced by disarm­
ing the system using any method. Navigate through the following menu path using OK and arrow keys to view the
violated zone or tamper number:
Menu path:
VIEW VIOLATED ZONE: OK → VIOLATED ZONES → ZONE [1... 44]
VIEW VIOLATED TAMPER: OK → VIOLATED TAMPERS → TAMPER [1... 44]
The built-in EKB3 mini-buzzer and ESIM264 mini-buzzer (if any) provide short beeps continuously in case of alarm. In
addition, the violated zone number is indicated by illuminated zone LED or flashing SYSTEM LED (if the violated zone
number is above 12). The violated tamper number is indicated by illuminated SYSTEM LED. The mini-buzzer can be
silenced by disarming the system using any method.
For more details on EKB3 violated high zone & tamper number indication, please, refer to chapter 3.10 Trouble Indications.
By default configuration, the siren (if any) provides continuous alarm sound for 1 minute in case of alarm. The fire
alarm is indicated by pulsing siren alarm sound. Siren alarm sound can be silenced by disarming the system using any
method.
3.5 Bypassing & Unbypassing Violated Zone
Arming the system is disabled while there’s at least 1 violated zone. Bypassing the zone allows to temporally disable a particular
violated zone and arm the alarm system after-wards.
EKB2
Navigate through the following path using OK and arrow keys to bypass a violated zone (-s):
Menu path:
Bypass a zone: OK → BYPASS → BYPASS LIST [1... 3] → ZONE [1... 44] → BYPASS
OK → BYPASS → BYP VIOLATED ZONES
Bypass all zones:
Navigate through the following path using OK and arrow keys to unbypass a violated zone:
Menu path:
Unbypass a zone: OK → BYPASS → BYPASS LIST [1... 3] → ZONE [1... 44] → UNBYPASS
NOTE: The alternative way to unbypass all zones at once is to arm and disarm the system.
EKB3
Bypass a violated zone by entering the following combination using [BYPS], number and [#] keys:
Enter zone number & user password:
[BYPSxxyyyy#]
Value: xx – zone number, range – [01... 44]; yyyy – 4-digit user password
Example: BYPS051111#
NOTE: The alternative way to unbypass all zones at once is to arm and disarm the system.
ATTENTION: Bypassing a violated tamper is NOT allowed. Please, restore the tamper (for example: close sensor‘s enclosure)
before arming the system
20
3.6 Viewing System Information
SMS
1. In order to find out the system‘s current information, send the following SMS message to the system‘s phone
number from any out of 5 preset user phone numbers:
SMS text:
XXXX_INFO
Example: 1111_INFO
2. The system will reply to the user phone number who sent the SMS message with the following up-to-date
information:
•
•
•
•
•
•
system date & time;
system status (armed/disarmed);
GSM signal strength level;
main power supply status;
temperature of the area surrounding ESIM264 temperature sensor (if any);
state of zones (OK/alarm).
SMS
SMS
User
ESIM264
Fig. No. 24
3.7 Managing Periodical System Information
SMS
1. By default configuration, the SMS message mentioned in chapter 3.6 Viewing System Information is sent
periodically to User 1 phone number at 11:00 daily.
SMS
User
ESIM264
Fig. No. 25
2. In order to set a different SMS sending frequency (in days) and time, send the following SMS message to the
system‘s phone number from any out of 5 preset user phone numbers:
SMS text:
XXXX_INFO:FF.TT
Value: FF – frequency in days, range – [0... 125]; TT – time, range – [0... 23]
Example: 1111_INFO:2.15 (every 2nd day at 15:00)
MANUAL ELDES ESIM264 V2.1
21
3. In order to disable periodic SMS message, send the following SMS message to the system‘s phone number
from any out of 5 preset user phone numbers:
SMS text:
XXXX_INFO:0.0
Example: 1111_INFO:0.0
4. The system will reply with confirmation by SMS message to the user phone number who sent the SMS message.
SMS
SMS
User
ESIM264
Fig. No. 26
3.8 Viewing Zone & PGM Output Information
SMS
1. In order to find out the current zone & PGM output information, send the following SMS message to the sys­
tem‘s phone number from any out of 5 preset user phone numbers:
SMS text:
XXXX_STATUS
Example: 1111_STATUS
2. The system will reply to the user phone number who sent the SMS message with the following up-to-date
information:
•
•
•
•
system status (armed/disarmed);
status of zones & PGM outputs (ON/OFF);
zone alarm texts;
PGM output names.
SMS
SMS
User
22
ESIM264
Fig. No. 27
3.9 Managing Temperature Information
SMS
1. If the temperature sensor is installed in your system, it can send an SMS message containing temperature value
in case the set lowest or highest temperature limit value is exceeded. This SMS message is sent to User 1 only. By
default configuration this SMS message is disabled.
SMS
User
ESIM264
Fig. No. 28
2. In order enable or set a different lowest and highest temperature limit value, send the following SMS message
to the system‘s phone number from any out of 5 preset user phone numbers:
SMS text:
XXXX_TEMP:MIN:MAX
Value: MIN - lowest temperature limit boundary in oC, range - [-55... 125];
MAX - highest temperature limit boundary in oC, range - [-55... 125]
Example: 1111_TEMP:-15:30
3. In order to disable temperature SMS message, send the following SMS message to the system‘s phone number
from any out of 5 preset user phone numbers:
SMS text:
XXXX_TEMP:0:0
Example: 1111_TEMP:0.0
4. The system will reply with confirmation by SMS message to the user phone number who sent the SMS message.
SMS
SMS
User
MANUAL ELDES ESIM264 V2.1
ESIM264
Fig. No. 29
23
3.10 Trouble Indications
EKB2
Message TBL displayed in the lower left side of the main screen view indicates presence of system troubles.
In order to find out more on the particular system problem, please, open menu section TROUBLES. The description on
each system problem is indicated in the table below.
Menu path:
OK → TROUBLES → T [1... 6]
EKB3
Trouble
Name
Description
TROUBLE 1
VIOLATED TAMPER
One or more tampers are violated.
TROUBLE 2
REPLACE BATTERY
Backup battery problem.
TROUBLE 3
AC FAILURE
Main power supply problem.
TROUBLE 4
TIME NOT SET
Date/time not set.
TROUBLE 6
GSM ERROR
GSM connection problem.
Yellow LED SYSTEM indicates system troubles. SYSTEM LED indications are mentioned in the table below.
SYSTEM LED
Description
Illuminated continously
One ore more zones or tampers are vio­
lated; other system troubles
Flashing
One or more high zones are violated
In order to find out more on the particular system problem, please, enter command A. After this procedure the system will activate red
zone LEDs for 15 seconds. The description on each LED indication is mentioned in the table below.
Zone LED
Description
1
One or more tampers are violated.
2
Backup battery problem.
3
Main power supply problem.
4
Date/time not set.
5
One or more high zones (Z13 - Z44) are violated.
6
GSM connection problem.
In order to find out which particular high zone is violated, please, enter command B.
In order to find out which particular tamper is violated, please, enter command C.
A. System trouble indication - enter command:
[CODE#]
B. Violated high zone indication – enter command:
[CODE1]
C. Violated tamper indication – enter command:
[CODE2]
24
The number of violated high zone or tamper can be calculated using the table below according to the formula: number from zone
LED section B + number from zone LED section A.
Example: LED #3 from section A is flashing and LED #8 from section B is illuminated continuously. According to the table below LED
#8 is equal to number 18, therefore 18 + 3 = 21.
Result: Violated high zone or tamper number is 21.
Zone LED section - A
(flashing)
Zone LED section - B
(illuminated continously)
Zone LED 1 = 1
Zone LED 7 = 12
Zone LED 2 = 2
Zone LED 8 = 18
Zone LED 3 = 3
Zone LED 9 = 24
Zone LED 4 = 4
Zone LED 10 = 30
Zone LED 5 = 5
Zone LED 11 = 36
Zone LED 6 = 6
Zone LED 12 = 42
3.11 Controlling Electrical Appliances
SMS
Your system features 4 or more PGM outputs intended for connection and control of various electrical appliances. This
provides a possibility to control garage gates, turn on and off your house heating, lighting, cooling system, reset smoke
sensors to restored state etc. The PGM outputs must be configured by your installer before using them.
1. In order to turn ON a specified PGM output, send the following SMS message to the system’s phone number
from any out of 5 preset user phone numbers:
SMS text:
XXXX_Cn:ON or XXXX_OutputName:ON
Value: Cn – PGM output number, range – [C1... C44]
Example: 1111_Pump:ON
2. In order to turn OFF a specified PGM output, send the following SMS message to the system‘s phone number
from any out of 5 preset user phone numbers:
SMS text:
XXXX_Cn:OFF or XXXX_OutputName:OFF
Value: Cn – PGM output number, range – [C1... C44]
Example: 1111_C2:OFF
3. The system will reply with confirmation by SMS message to the user phone number who sent the SMS message.
SMS
SMS
User
MANUAL ELDES ESIM264 V2.1
ESIM264
Fig. No. 30
25
3.12 Turning ON/OFF the Electrical Appliances for a Determined Time Period
1. In order to instantly turn ON a specified PGM output and keep it in this state for a determined time period, send the follo­
wing SMS message to the system’s phone number from any out of 5 preset user phone numbers:
SMS text message content:
XXXX_Cn:ON:hr.mn:sc or XXXX_OutputName:ON:hr.mn:sc
Value: Cn – PGM output number, range – [C1... C44]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59];
sc – seconds, range – [00... 59].
Example: 1111_Pump:ON:12:30:15
2. In order to instantly turn OFF a specified PGM output and keep it in this state for a determined time period, send the following
SMS message to the system’s phone number from any out of 10 preset user phone numbers:
SMS text message content:
XXXX_Cn:OFF:hr.mn:sc or XXXX_OutputName:OFF:hr.mn:sc
Value: Cn – PGM output number, range – [C1... C44]; hr – hours, range – [00... 23], mn – minutes, range – [00... 59];
sc – seconds, range – [00... 59].
Example: 1111_C3:OFF:13.25:56
3. The system will reply with confirmation by SMS text message to the user phone number who sent the SMS message.
SMS
SMS
User
ESIM264
Fig. No. 31
4. If the Alarm System is Connected to Monitoring Station
The following system features become disabled automatically or may be disabled by your alarm system installer if the system is con­
nected to a monitoring station:
• Confirmation by SMS message when arming, disarming & turning off the alarm by phone call, SMS message, EKB2/EKB3
keyboard, iButton® key, EWK1 - wireless key-fob;
• Alarm indication by phone call;
• Alarm indication by SMS message;
• Violated zone/tamper name indication by SMS message;
• Temperature indication by SMS message;
• Periodical system information by SMS message;
• Main power loss/restore indication by SMS message.
NOTE: For full system configuration and control, please refer to ESIM264 installation manual located at
www.eldes.lt/en/download
Made in Lithuania.
www.eldes.lt
iButton is a registered trademark of Maxim Integrated Products, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement