Fortress Technologies Winner 3 Owner's Manual

OWNER‘S MANUAL
3 & 4 Wheel Scooters
Issue 4
October 2010
Handicare®
All rights reserved.
The information provided herein may not be reproduced and/or published in any form, by print,
photoprint, microfilm or any other means whatsoever (electronically or mechanically) without the
prior written authorisation of Handicare®.
The information provided is based on general data concerning the constructions known at the time
of the publication of this manual. Handicare executes a policy of continuous improvement and
reserves the right to changes and modifications.
The information provided is valid for the product in its standard version. Handicare® cannot be
held liable for possible damage resulting from specifications of the product deviating from the
standard configuration.
The available information has been prepared with all possible diligence, but Handicare® cannot be
held liable for possible errors in the information or the consequences thereof.
Handicare accepts no liability for loss resulting from work executed by third parties.
Names, trade names, etc. used by Handicare® may not, as per the legislation concerning the
protection of trade names, be considered as being available.
XXXXXX-000001000-en.doc
2
Table of contents
Introduction ........................................................................................ 5
This manual ........................................................................................ 5
Product labels..................................................................................6-7
Symbols used in manual.................................................................... 8
Service and technical support........................................................... 9
Identification plate.............................................................................. 9
Identification of the product .............................................................. 9
Warranty....................................................................................... 10-11
Use according to purpose ............................................................... 12
1 General safety regulations and instructions............................ 13
1.1 Labels and instructions on the scooter ............................ 13
1.2 Technical specifications................................................... 13
1.3 Modifications ................................................................... 13
1.4 Safety......................................................................... 13-15
2 General description ................................................................... 16
3 Main components.................................................................. 17-18
4 Operation.................................................................................... 19
4.1
Driving with the Fortress Winner........................................ 19
4.1.1 Inspection before use................................................ 19
4.2
Operating Controls .............................................................. 20
4.2.1 Console ............................................................... 21-23
4.2.2 Switching on ............................................................. 24
4.2.3 Charging connection ................................................. 24
4.3
Driving Procedures.............................................................. 25
4.3.1 Driving forward and in reverse .................................. 25
4.3.2 Corners..................................................................... 26
4.3.3 Slopes....................................................................... 27
4.3.4 Obstacles.................................................................. 28
4.3.5 Overload Shutdown .................................................. 29
4.3.6 Switching off ............................................................. 29
4.3.7 Parking ..................................................................... 30
4.3.8 Charging the batteries............................................... 30
4.3.9 Battery charger ......................................................... 31
4.4
Transferring in and out........................................................ 32
4.5
Pushing the scooter ............................................................ 32
4.5.1 Freewheel position of the scooter ............................. 33
4.6
Reducing the size of the scooter for storage .................... 34
4.6.1 Removing the seat .................................................... 34
4.6.2 Folding down the steering tiller.................................. 35
4.7
Transport.............................................................................. 35
3
5 Adjustment options ................................................................... 36
5.1
Seat adjustments................................................................. 36
5.1.1 Adjusting the seat height .......................................... 36
5.1.2 Adjusting the seat depth ........................................... 36
5.1.3 Backrest adjustment ................................................. 37
5.1.4 Adjusting the armrest................................................ 37
5.1.5 Adjusting the headrest ............................................. 38
5.2 Adjusting the steering tiller...................................................... 38
6 Maintenance............................................................................... 39
6.1
Maintenance table ............................................................... 39
6.1.1 Batteries ................................................................... 39
6.1.2 Replacing the batteries ............................................. 40
6.1.3 Cleaning the batteries............................................... 41
6.2
Tires ..................................................................................... 42
6.2.1 Inflating the tires ....................................................... 42
6.3
Cleaning............................................................................... 43
7 Troubleshooting ........................................................................ 44
7.1
Troubleshooting table.................................................... 44-45
7.2
Automatic circuit breaker ................................................... 46
7.3
EMI malfunction .................................................................. 47
8 Technical specifications ........................................................... 48
8.1
Product specifications Fortress Winner....................... 48-49
8.2
Approval .............................................................................. 50
8.3
Authorized service and technical support......................... 51
4
Preface
Introduction
Thank you for choosing a Fortress Winner electric scooter.
Welcome to a growing community of people who use a scooter from the
Handicare product range.
Handicare stands for reliability and innovative technology, which results in
easily operated quality products.
XXXXXX-010001000-en.doc
This manual
With this manual you can safely use and maintain the product. In case of
doubt always contact your dealer.
In this manual, the words "left", "right", "front" and "back" are used to indicate a
certain part of the product. This is viewed from the position of the user seated
on the scooter.
XXXXXX-010003000-nl.doc
Please refer to the back cover of this manual to find to your scooter’s serial
number, model description, and your authorized Handicare dealer. This
information will be helpful for any product assistance that you may require
In the future.
5
Preface
Product Labels
XXXXXX-010004000-en.doc
B
A
D
C
E
The product has the following decals and labels:
A.
B.
C.
D.
E.
F.
6
Charging connection
Fuse for lighting
Circuit breaker
Freewheel
Tire pressure wheels
Tilt steering adjustment
F
Preface
Product Labels
A. Charging connection
For charging of the batteries, see 'Charging the batteries'.
PICPRO-010004210-en.doc
B. Fuse for the lighting
Here you will find the fuse for the lighting. See 'Product
specifications sheet'.
C. Circuit breaker
The scooter has a safety breaker feature. See ‘Automatic
circuit breaker’.
PICPRO-010004270-en.doc
D. Freewheel
1.
Lever in the uppermost position:
The drive of the motor has been switched on: The
scooter can be electrically driven.
2.
Lever in the lowermost position:
The drive of the motor is disconnected: the scooter can
be pushed manually.
E. Tire pressure
MAX.
2,7
BAR
For tire pressure of the wheels, see 'product specifications’.
F. Tilt steering adjustment
Adjust the steering tiller to obtain a position that is most
comfortable for you while driving. See ‘Adjusting the
steering tiller’.
7
Preface
Symbols used in this manual:
XXXXXX-010004020-en.doc
CAUTION
Procedures that can result - if they are not executed
properly - in damage to the product, the environment, or
human injury.
PICDOC-010004110-en.doc
ATTENTION!
Suggestions that help specific procedures to be carried out
more easily.
PICDOC-010004120-en.doc
Consult the specified information source(s) first.
PICDOC-010004130-en.doc
Pull the charge cord out of the charging connection of the
scooter before doing any maintenance on the scooter.
PICDOC-010004140-en.doc
8
Preface
Service and technical support
For information concerning specific settings, maintenance or repair work
please contact your dealer. He is always prepared to help you.
Ensure you have at hand:
Model
Serial number
This information is provided on the identification plate. See diagram below.
XXXXXX-010006000-nl.doc
Identification plate
Product information can be found on
plate (A). See: 'Identification of the
product'.
A
Identification of the product
•
See Fig. 010007010.
XXXXXX-010007010-en.doc
A
B
C
¨
Model
Year of manufacture
Serial/Identification number
User area indoors or outdoors
Maximum load in kg
LAGE DIJK 10
5705 BZ HELMOND
THE NETHERLANDS
A.
B.
C.
D.
E.
CAT
2000
IDNR.: CT 00004
USAGE:
INDOOR/OUTDOOR
GEBRUIKSGEBIED: BINNEN/BUITEN
GEBRAUCHSBEBIET: INNERHALB/AUSSERHALB
MAX.LOAD/MAX.BELASTB./ZUL.GESAMTGEW.: 100 KG
TYPE/TYPE/TYP:
YEAR/JAAR/JAHR:
D
E
9
Preface
Warranty
Handicare warrants to the original buyer that the new equipment sold by an
authorized Handicare dealer is, at the time of delivery to the buyer and for the
period of three years immediately following such delivery, free from defects in
material and workmanship and meets designed performance levels.
Handicare agrees that it will during such three-year period, either repair or
replace, at Handicare’s sole option, any part or parts of new equipment which
under proper and normal conditions of use proves to be defective or fails to
meet designed performance levels. The above warranty is extended or
otherwise modified for certain components of the equipment as specified
below:
Handicare supplied scooter’s Main Frame Weldment is covered under a
lifetime warranty. The battery charger is covered under a two-year warranty.
The seat assembly, basket, and optional accessories are covered under a
one-year warranty.
Exclusions and Limitations
• Equipment modified other than by Handicare is not covered by this
warranty.
• Tires, inner tubes plastic covers, brake pads, motor brushes, bearings,
chain, arm pads and upholstery are considered wear items and are not
covered by this warranty.
• Cosmetic appearance of items will change as a result of use and are not
covered by this warranty.
• Items added to the equipment by the buyer or by a user are not covered
by this warranty.
• Any damage to items added to the Handicare supplied equipment, caused
by the Handicare supplied equipment, is not covered under this warranty.
Any damage to the Handicare supplied equipment by the additional
equipment is also not covered by this warranty.
• Any use of the equipment outside the criteria published in the current
Handicare sales brochures, or beyond the manner, in which a prudent
person would normally use the equipment, will void this warranty (i.e.
Abuse and misuse).
• Labour and shipping are not covered by this warranty.
• Any batteries supplied by Handicare are covered by the battery
manufacturer’s standard warranty.
10
Preface
Warranty
All claims for warranty-covered parts under the above warranty must be
presented to Handicare by an authorized dealer within forty-five (45) days of
the event upon which any warranty claim is made. Handicare reserves the
right to refuse the warranty claim should the claim not satisfy the basic
requirements.
The foregoing warranty is exclusive and in lieu of all other express warranties.
Implied warranties, if any, including but not limited to the implied warranties of
merchantability and fitness for a particular purpose, shall not extend beyond
the duration of the express warranty provided herein. Handicare shall not be
liable for any consequential or incidental damages whatsoever.
For all warranty inquiries, please contact your authorized Handicare
dealer.
Recommendations
Please complete the Handicare Warranty Registration Card. Mail it to
Handicare within 10 days of delivery of the equipment. This will assist
Handicare to initiate and to provide your appropriate warranty coverage.
It is strongly recommended that your equipment receive an annual service
inspection by an authorized Handicare dealer within 30 days of the
anniversary of the purchase date.
11
Preface
Use according to purpose (1)
The Fortress Winner scooter is designed for:
•
•
•
transport of persons with a weight of up to 350 lbs (159 kg)
use on sidewalks, footways, and bike-ways
use in and around the house.
Your dealer should give you clear instructions before you independently
operate the product.
Consider operating the Fortress Winner scooter under the supervision of an
experienced dealer during first test drives.
The Fortress Winner scooter is not classified as a road vehicle and as such is
not permitted for road use (road crossing are the only exception).
The Fortress Winner has a maximum speed of 15 km/h (9.3 mph).
PLEASE MAKE SURE YOU ARE WELL ACQUAINTED WITH THE
CONTENTS OF THIS OWNER’S MANUAL BEFORE DRIVING THE
FORTRESS WINNER.
If you use the scooter for other purposes than those for which it is intended,
Handicare accepts no liability whatsoever for damage or injury resulting from
such use other than that for which the scooter was developed and designed.
(1)
Use according to purpose' as established in EN 292-1 is the use for which the technical product is suitable according to
the statement of the manufacturer, including his instructions in the sales brochure. In case of doubt this is the use that
follows from the construction, execution and function of the product. Use according to purpose also includes taking into
consideration the instructions in the user manual.
12
General safety regulations and instructions
1 General safety regulations and instructions
Handicare accepts no liability whatsoever for damage or injury caused by the
failure to (strictly) adhere to the safety guidelines and instructions or else due to
carelessness during the use and cleaning of the scooter and possible
accessories. Depending on the specific operating circumstances or the
accessories used, additional safety instructions may be required. Please contact
your dealer immediately if you observe any potential danger during the use of
the product.
The user of the scooter (see under 'use according to purpose') is
at all times fully responsible for the fulfilment of the locally
applicable safety regulations and guidelines.
1.1
Labels and instructions on the scooter
Signs, symbols and instructions placed on this scooter comprise part of its
safety facilities. They must never be covered or removed and must remain
present and clearly legible throughout the entire life span of the scooter.
•
Immediately replace or repair illegible or damaged labels, symbols and
instructions. Contact your dealer with regard to this.
1.2
Technical specifications
The technical specifications must not be altered.
1.3
Modifications
Modifications to (parts of) this product are not permitted.
1.4
Safety
To avoid accidents and undesirable situations, it is of great importance to pay
attention to the following safety instructions.
• Pay extra attention to driving on slopes:
- Never drive the Fortress Winner up a slope with an angle
greater than 10°.
- On slopes always drive slowly and with great awareness.
- Never drive down a slope at full speed.
- Do not drive down slopes with loose gravel or a sandy
surface, because one of the back wheels might slip.
- Do not turn on a slope.
• Never take a turn at full speed. Decrease speed when taking a
turn.
13
General safety regulations and instructions
• Be sure that no items of clothing hang loose. These could
become caught between the wheels.
• Make sure your fingers do not get caught in the mechanism of
the tilt steering adjustment.
• Adjust your driving according to the circumstances:
- Drive carefully on slippery roads, resulting from rain, ice, or
snow!
- Drive more slowly in crowded environments.
- Do not use the scooter on uneven roads.
- Avoid the Fortress Winner from coming into contact with sea
water. Sea water is caustic and may damage the scooter.
- Avoid the Fortress Winner from coming into contact with sand.
Sand can affect the moving parts of the scooter, resulting in
unnecessarily rapid wear.
• Never operate the scooter when you are under the influence of
drugs, alcohol or medication that could affect your driving ability.
• You must have sufficient visual acuity to be able to drive safely in
the scooter.
• It is imperative to turn on the lights in case of reduced visibility.
• The scooter has been equipped with brake lights that light up
when you brake.
• Only use the indicator lights to indicate an intended change in
driving direction.
• Only use the horn when it is necessary to warn pedestrians of
other road users of dangerous circumstances.
• Never place metal parts on top of the batteries: this may cause a
short circuit in the batteries, resulting in damage.
• Do not carry any passengers: your scooter was specifically
designed to transport only yourself.
• Do not burden your scooter with any more load than can be
placed in the basket.
• Never hang anything from the handlebars.
• Never use your scooter to tow a trailer: the scooter was not
designed for this. It can cause serious damage to your scooter.
• Do not stand on the floor pan to reach objects.
• Do not place your feet close to the front wheel and fork when the
unit is moving. Always keep your feet on the rubber mat, rather
than against the front cover.
14
General safety regulations and instructions
• The scooter is electronically operated. Certain parameters have
been factory-set. These settings are designed to allow
comfortable and efficient use. These parameters cannot be
changed.
• The standard version of your scooter was tested according to the
strictest EMC requirements. Mobile telephones have no influence
on the driving behaviour of the scooter.
When using a mobile telephone in the vicinity of a scooter
with special adaptations, you are advised to first switch off
the scooter.
• Your scooter may influence electromagnetic fields such as alarm
systems.
• If the electronics of the scooter is not properly screened off, this
may affect sensitive electrical appliances, such as shop alarms
and garage openers. The scooter has been tested for this.
Should any problems of this nature occur, please report these to
your dealer immediately.
• Take care in ultra-violet light: this may cause premature
deterioration of materials such as rubber, plastic, and enamel.
• Be aware of any objects that may protrude from the unit that
could cause damage to your surroundings or to the unit itself.
• Keep your scooter away from open flames.
15
General description
2 General description
The Fortress Winner is an electrically driven scooter for general use or for
longer distances.
The height of the seat is adjustable according to the leg length of the user. The
seat can be rotated and the armrests folded back by the user when he/she
wants to make a transfer on or off the scooter.
The tiller is adjustable to enable a comfortable driving position.
When driving at higher speeds, one should be extra careful. Slow down,
especially on sidewalks and in pedestrian areas.
The following should be kept in mind when using the scooter:
•
A scooter is not a motorised vehicle in the traffic regulations sense. You
have the same rights and duties as a pedestrian.
•
At all times, you are responsible for keeping your scooter in perfect working
order, so that driving the scooter is safe.
•
The scooter is a technical product. Therefore, any repairs and maintenance
should be carried out by qualified personnel. If any work needs to be done,
you should contact your dealer.
16
Main components
3 Main components
•
See Fig. 0000000020.
The following main components are, or may be, installed on the scooter:
A. Seat.
This is where the user is seated.
B. Backrest.
To support the back of the user.
C. Head rest
To support the head.
D. Armrest.
To support the arms
E. Steering Tiller
The dashboard and all operating keys and handles are located on the tiller
F. Lights
When driving in the dark the lights should be turned on
G. Turn Signals
To indicate a change in direction while driving
H. Detachable frame-mounted basket
For carrying personal items
I. Front wheel
Front wheels offer suspension
J. Front bumper
Protects the front wheel in case of a collision
K. Rear wheels
Rear wheels offer suspension
(See next page for location of these components on the scooter)
Various features and components can be adjusted for optimum seating
comfort.
17
Main components
E
C
G
B
H
D
A
F
J
K
Also available in 4 wheel con
I
4-wheel configuration:
18
Operation
4 Operation
XXXXXX-010400000-nl.doc
4.1
Driving with the Fortress Winner
To be able to drive, this owner’s manual describes the following:
•
Inspection before use
•
Console
•
Driving
•
Transferring in and out
•
Pushing
•
Disassembly
4.1.1 Inspection before use
Before one starts driving the scooter, it is important to check the following
items:
•
make sure the seat is properly locked in place.
•
make sure all lights and turn signals are working properly, both at the front
and the back.
•
make sure the tires are sufficiently inflated. See ‘Product specifications’.
- Poorly inflated tires have a negative effect on the driving
characteristics.
- Poorly inflated tires cause a higher power consumption, depleting the
batteries more quickly.
- Poorly inflated tires cause unnecessary wear to the tires themselves.
•
make sure the batteries are charged sufficiently: this is indicated by the
green zone on the battery-condition indicator. See ‘Console’.
In winter, batteries have a lower capacity. In case of light frost,
the capacity drops to about 75% and at a temperature of less
than -5 degrees, it will drop to about 50% of the normal capacity.
This will decrease the range of the scooter..
•
•
make sure the free-wheel lever is in the ‘Brake Engage’ position. See ‘Free
wheel position of the scooter’.
make sure the brakes are functioning correctly. See ‘driving procedures’.
19
Operation
If the scooter starts behaving in an unpredictable manner, let go of the throttle
levers and let the scooter come to a complete stop. Remove the jack key from
the console and then reinsert to restart the scooter.
If everything is in order, the scooter can be driven.
4.2
•
Operating controls
See Fig. 000000030.
The scooter is equipped with the
following operating controls:
A. Console with all operating switches
B. Forward / reverse levers
C. Fuse for the lighting
D. Charger connection port. See
‘Charging the batteries’.
E. Tilt steering lever for tiller
adjustment.
F. Front brake with parking lock
(NOT APPLICABLE IN CANADA)
F C
A
B
E
D
000000030
20
Operation
4.2.1 Console
•
See Fig. 000000040.
A
B C
F
G
D
F
E
A
000000040
The console is provided with the latest technology and offers reliable and
useful functions for the operation of your scooter:
A.
B.
C.
D.
E.
F.
G.
Left & right turn signals*
Battery-condition meter
Speed control
Lighting
Jack key
Horn*
Hazard lights
*These switches have been mounted on both the right and the left of the
console.
21
Operation
A
Turn Signals left / right
By activating the switch (on the left or on the right), the indicator
concerned will start flashing, to indicate that you intend to
change your driving direction:
move the switch to the left if you wish to turn to the left;
move the switch to the right if you wish to turn to the right.
As soon as you have completed your left or right turn, move the
switch to its neutral position to switch off the indicator.
B
Battery-condition Meter
The battery-condition meter gives a general indication of the
condition of the batteries. It is quite normal for the pointer to go
down during acceleration, because the battery voltage is
reduced when power is requested. This voltage reduction is no
indication for the capacity of the batteries. When the batteries
are fully charged, the pointer will be at its maximum position.
However, this will also be the case if the batteries are not fully
charged, owing to the battery’s characteristics.
The most reliable battery indication is shown while driving on a
flat surface.
The battery-condition meter has three areas in which the
pointer may rest after the scooter is switched on.
When the battery is sufficiently charged, the pointer is in the
green area. As the battery is depleted, the pointer will move to
the yellow, and, subsequently, into the red area.
The fields have the following meaning:
Red: The batteries are depleted and have to
be recharged as soon as possible.
Yellow: The batteries are quite depleted.
The scooter may be used, but the
batteries should very soon be recharged.
Green: The batteries are fully charged.
C
22
Speed Control Knob
With this knob, the desired maximum speed is set. Turning
clockwise will increase the speed (the maximum has been set
by the manufacturer to 15 km/h).
Turning counter clockwise will reduce the maximum speed.
Select the position of this button beforehand, in accordance
with the driving conditions, such as driving in cramped spaces
or in a room with many people.
Operation
D
Lighting
Pressing this switch will turn on the lighting:
The switch has the following positions:
0: lighting is off
1: lighting is on.
F
Horn
The horn buttons are used to give a warning sound in
dangerous situations.
The horn will sound for as long as you keep the button pressed.
E
Jack Key
To switch on the scooter, the jack key has to be inserted into
the jack key receptacle.
All of the Fortress Winner’s functions, with the exception of the
hazard lights and the lighting, only operate if the jack key has
been inserted into the receptacle.
The hazard lights and the lighting will always work, even if the
contact plug has not been put into the contact.
G
Hazard Lights
Pressing this switch will turn on the hazard lights.
You should use the hazard lights if you fear you will not be seen
by other traffic, or if you are stopped because of a malfunction.
Pressing this switch a second time will switch off the hazard
lights.
23
Operation
4.2.2 Switching on
•
See Fig. 000000050.
A
The scooter should be switched on as
follows:
•
Put the jack key into the jack key
receptacle as far as it will go (A).
000000050
4.2.3 Charging connection
•
See Fig. 000000060.
On the steering column underneath
the console, there is the charger
connection port (A) to which the
battery charger cable can be
connected.
All electronics should be switched off
during charging of the batteries.
Remove the jack key before charging.
•
A
000000060
24
Operation
4.3
Driving Procedures
Before driving with the scooter, it should be adjusted optimally to your personal
needs.
After you have carried out all inspection points, you can seat yourself in the
scooter. See ‘Transferring in and out’.
Now you may start your ride.
As a scooter driver, keep in mind that other traffic participants may not always
notice you. Keep to the current traffic regulations.
4.3.1 Driving forward and in reverse
•
See Fig. 000000070.
•
Switch on the scooter. See ‘Switching
on’.
The forward/reverse handles are
coloured:
Green: forward driving
Yellow: reverse driving
B
A
Forward driving
C D
•
Driving forward using thumb control:
000000070
Slowly push forward on the
forward/reverse lever (A) with your thumb. The further you push the lever
forward, the faster you will drive.
•
Driving forward using finger control:
Slowly pull back on the forward/reverse lever (D) with your fingers. The
further you pull the lever towards you, the faster you will drive.
Reverse driving
Reverse driving:
Release the forward/reverse lever. The Fortress Winner will come to a stop.
•
Driving in reverse using thumb control:
When the scooter has come to a complete stop, slowly push the
forward/reverse lever (C) forward with your thumb. The further you push the
handle forward, the faster you will drive in reverse.
•
Driving in reverse using finger control:
Slowly pull back the forward/reverse lever (B) with your fingers. The further
you pull the lever towards you, the faster you will drive in reverse.
•
• Make sure there is nothing behind the scooter before you
travel in reverse.
• The maximum speed in reverse is equal to half the maximum
speed forward.
25
Operation
Braking and stopping while driving forward or reversing
•
If you release the forward/reverse lever slowly, the Fortress Winner will
brake and come to a stop.
While braking, the brake lights will go on.
•
If you need to make a sudden stop while driving, you must release the
forward/reverse lever immediately.
In normal circumstances, you can release the forward/reverse lever slowly
when you want to stop.
As soon as the scooter is stopped, the automatic parking brake is applied.
Remarks:
You can inspect the brakes by suddenly releasing the forward/reverse lever.
• When driving at a high speed, you need to be extra careful,
especially on sidewalks and in pedestrian areas. In that case, it is
advisable to set a lower maximum speed using the speed control
knob.
• Do not cross a street until you are able to handle the scooter and
its controls well.
4.3.2
Corners
Moving around corners in forward direction
Turning left or right
•
By turning the handlebars to the left or to the right, the scooter will change
direction and start moving to the left or to the right accordingly.
• You should always use your turn signals when making a turn.
• Always take turns at a safe, often lower, speed.
Reversing while making a turn
Turning left or right
•
By turning the handlebars to the left or to the right, the scooter will change
direction and start moving in the opposite direction of the direction you steer.
- Steering to the right: the scooter will reverse while making a left turn.
- Steering to the left: the scooter will reverse while making a right turn.
26
Operation
4.3.3
Slopes
• Maximum slope which can safely be driven with maximum weight
according to ISO 7176-2 is 10° at 159 kg.
• Slopes with an angle greater than 10° may not be taken.
• Avoid sudden and jolting movements, such as sudden braking, to avoid
the possibility of the scooter becoming unstable.
• Do not brake too hard when moving around corners.
• Avoid changing directions or turning around on a slope.
• Do not turn on slopes steeper than 10°.
Driving up a slope
•
Driving up a slope is done in the
same way as driving in forward
direction.
• Lean slightly forward with
the upper part of your
body, while driving up a
slope. This will provide the
scooter with more
o
max. 10
stability.
• Drive up a slope at half
speed.
Drive at a constant speed.
• If you notice a strong decrease in speed when driving on a slope,
choose a less steep route, to avoid the scooter from getting
overheated.
• If you drive on a slope too long, this may result in overheating of
the electric motor.
• If you want to drive up a steep slope and the speed of your
scooter decreases drastically, you should find an easier route.
Remarks:
Whenever possible, choose a road that is not so steep.
Driving down a slope
•
If you need to drive down a slope, drive at the lowest possible speed and
with the utmost control.
• Turn the speed control fully to the left (lowest speed) before
driving down a slope.
• Move the upper part of your body slightly backward and always
brake slowly. If you brake fast, you may cause the scooter to tip
over forward.
27
Operation
4.3.4 Obstacles
•
See Fig. 000000090.
Driving up obstacles
•
•
•
Drive straight up to the curb, almost touching it with your front wheel.
Push the forward/reverse lever and drive onto the sidewalk without changing
direction.
As soon as the front wheel is on the sidewalk, you need to keep up your
speed for the back wheels to be able to move up onto the sidewalk as well.
-
28
If you cannot drive up onto the sidewalk, find a lower part that is less
steep where you can.
Any obstacle should be taken in forward direction.
It is always recommended to use properly-designed sidewalk
transitions instead of driving over curbs.
Do not drive over obstacles great than 10 cm (3.9”).
Operation
Practice taking slightly elevated obstacles. Once you are
practised at these, gradually increase the elevation of the
obstacles, until you can take the maximum height. Take your time
for this.
Driving off obstacles
•
•
•
Use extreme caution when driving off obstacles.
Drive straight up to the edge of the sidewalk until you reach the curb.
Carefully push the operating handle and allow the scooter to slowly descend
from the curb, without changing direction.
• It is not permitted to go down stairways.
• The scooter is equipped with anti-tipping wheels for extra stability
and safety. Occasionally, these wheels may touch an obstacle
when driving down one.
• Avoid leaving one of the back wheels on the obstacle, while the
other is still on the lower level. This will cause the scooter to
become unstable.
4.3.5 Overload Shutdown
•
In case of overload, caused by wrong or long-term use in hot conditions, the
circuit breaker will be activated, causing the scooter to stop. See ‘Automatic
circuit breaker’.
•
Abuse may also cause unnecessary malfunctions and damage to the
scooter.
4.3.6 Switching off
After each ride, the scooter should be switched off completely: This prevents
the batteries from unnecessarily discharging and having to be recharged too
soon.
29
Operation
4.3.7
Parking
After parking, pull out the jack key from the jack key receptacle, so that no one
can use your Fortress Winner without permission.
After the scooter has been switched off (the jack key has been pulled out of
the receptacle), the automatic parking brake will remain activated even if the
batteries are removed. If the freewheel position has been activated, the
automatic parking brake will NOT work!
If the scooter is stopped on a slope, the automatic parking brake
should be activated.
Never put the scooter in the freewheel position if it is on a slope.
4.3.8
Charging the batteries
For charging, see the following documentation:
• Regulations concerning the batteries.
• User manual for the battery charger, or the instructions on the
battery charger.
The scooter uses gel batteries. These batteries are entirely sealed and
maintenance free.
With normal daily use, the batteries should be recharged every night.
Charging should be done as follows:
•
•
•
•
Switch off the scooter.
Put the plug of the charging cable into the charging connection. See
‘Charging connection’.
Put the plug of the battery charger into the wall socket of the main power
supply.
Switch on the battery charger.
Safety:
The scooter will not operate as soon as the plug of the charging
cable is connected to the charging connection.
30
Operation
• The battery charger has been designed in such a way that
batteries cannot be overcharged.
• When the batteries are no longer charging, the charging current
will automatically drop until the charging is stopped completely:
the batteries are fully charged.
• The minimum charging time for gel batteries is approximately 8
hours. Most batteries will have reached 80% of their capacity
after an 8-12 hours’ charging time.
When the batteries are charged:
Switch off the battery charger, if applicable.
Take the plug of the battery charger from the wall socket of the mains power
supply.
•
Take the plug from the charging connection.
•
•
The scooter is now ready for use.
Always remove the charging cable when the batteries are
charged. This way, you prevent the batteries from slowly
depleting themselves.
4.3.9
Battery Charger
Use the originally-supplied battery charger to charge your Fortress Winner
scooter.
31
Operation
4.4
•
Transferring in and out
See Fig. 000000100 (seat may differ
slightly from diagram)
Before transferring on or off,
the scooter should be
switched off by removing
the jack key and the
automatic parking brake
should be engaged.
•
A
Before making a transfer, the armrest
can be flipped up and the seat can be
rotated.
000000100
Transferring in:
•
Switch off the scooter.
•
Move the seat-lock handle (A) toward the front of the scooter and turn the
seat 90 degrees to the left or to the right. When you release the seat-lock
handle, the seat will automatically lock: the handle will click into place.
•
Now seat yourself on the seat.
•
Turn back the seat as described above.
When the seat has been turned to its original position, it will click back into
place. This way, it cannot inadvertently turn while driving.
The seat is provided with armrests that can be flipped up so that you can
transfer in and out sideways. After transferring in or out, always check whether
the armrests are in the proper position.
•
Transferring out should be done in reverse order.
4.5
Pushing the scooter
In the case of a malfunction or if the batteries have insufficient capacity to
power the scooter, it may also be pushed manually.
Pushing the scooter may be useful for parking or storing the scooter in a
confined space.
•
•
32
Switch off the scooter by removing the jack key from the receptacle.
Switch the free wheel lever into the ‘Free wheel position of the scooter’.
Operation
If the scooter is pushed too fast, the speed will automatically slow
down, or the scooter will automatically brake.
4.5.1 Free wheel position of the
scooter
•
See Fig. 000000110.
To be able to push the Fortress Winner,
the automatic parking brake has to be
de-activated as follows:
•
Move the free wheel lever (A), located
on the right-hand side of the cover,
underneath the seat, into the FREE
WHEEL (C) position. This deactivates the automatic parking brake.
The Fortress Winner’s automatic brake is
activated again by moving the free wheel
lever to BRAKE ENGAGE position(B).
B
A
C
000000110
Safety precautions in the free wheel position
The scooter has been provided with a unique safety feature that prevents the
scooter from rolling too quickly while in the free wheel position. With the jack
key inserted while in the free wheel position, the motor brake will automatically
slow down the scooter to walking speed.
• Make sure the free wheel lever is in the BRAKE ENGAGE
position when you seat yourself on the scooter.
• NEVER touch the free wheel lever while driving.
• Do not touch the forward/reverse lever when you operate the free
wheel lever.
The free wheel lever should only be used if the scooter is to be
pushed. By putting the scooter in the free wheel position, the motor is
disconnected mechanically, causing the automatic parking brake of
the motor not to function. That is why, after pushing the scooter, the
lever should immediately be returned to the ‘Brake Engage’ position,
which will activate the automatic parking brake.
33
Operation
Attention:
NEVER switch the scooter into free wheel when you are parked on
a slope: the scooter will start moving down the slope as a result of
gravity.
If the Fortress Winner is in the free wheel position:
•
It is not possible to drive electrically.
•
The electronics can be switched on, but the motor cannot drive the scooter.
In this situation, the electronics should be switched off.
To be able to drive the Fortress Winner electrically again, the following steps
should be carried out:
•
Switch the free wheel lever into the Brake Engage position.
•
Switch the scooter on by inserting the jack key into the jack key receptacle.
Now, you are able to drive the Fortress Winner again.
4.6
Reducing the size of the scooter for storage
The size of the Fortress Winner can be reduced as follows:
•
By removing the seat. See 'Removing the seat'.
•
By folding down the steering tiller. See ‘Folding down the steering tiller’.
By replacing the seat and by putting the steering tiller back to its operating
position, the Fortress Winner is ready for immediate use again. See the
descriptions concerned.
4.6.1 Removing the seat
•
See Fig. 000000120 (seat may differ
slightly from diagram)
The seat should be removed as follows:
•
Unlock the turning mechanism of the
seat by pushing the seat lock lever
toward the front of the scooter.
•
Lift the seat from the seat post.
•
The seat is easily lifted out if it is
turned slightly in the process.
•
Folding the backrest completely
forward reduces the size of the seat
and can make it easier to lift from its
post.
34
A
000000120
Operation
4.6.2 Folding down the steering tiller
•
See Fig. 000000130.
A
The steering tiller can be folded down as
follows:
•
Pull handle (A) down, while, at the
same time, pulling down the steering
tiller.
Use caution when folding
down the steering tiller to
avoid getting your fingers
jammed.
000000130
4.7
Transport
To be able to easily transport the Fortress Winner scooter in a vehicle suitable
for this purpose, the Fortress Winner can be disassembled. This way, it will
take up less space. See ‘Reducing the size of the Fortress Winner’.
• Never lift the scooter by its plastic cover.
• Considering the nature of the scooter, the user is supposed to
make a transfer to a regular car seat. You may not be transported
in a car or taxi while sitting on the scooter, even if the vehicle
concerned has been adapted for the transport of scooters. The
reason is that the Fortress Winner cannot offer the safety that is
offered by standard car seats, no matter how well the Fortress
Winner is fixed to the vehicle concerned.
• After the scooter has been placed inside the vehicle, you must
make sure that the scooter is not in the free wheel position.
• The scooter must be secured with lashing straps to the front and
the back.
• Note that the disassembled seat can cause damage as a result of
vehicle movements.
• The seat post may be greasy.
35
Adjustment options
5 Adjustment options
XXXXXX-010500000-en.doc
5.1
Seat adjustments
The Fortress Winner seat offers a number of adjustment options to increase
the sitting and driving comfort.
The following may be adjusted:
A. Seat height
B. Seating depth
C. Backrest angle
D. Armrests width
E. Head rest
F. Steering tiller
5.1.1 Adjusting the seat height
The whole seat may be adjusted in height up to a range of 3”.
This adjustment should be made by the dealer.
5.1.2 Adjusting the seat depth (sliding seat)
•
See Fig. 000000180 (seat may differ
slightly from diagram)
Adjust the seat depth as follows:
•
•
•
Pull lever (A) up and hold.
Slide the seat forward or back.
Release the handle when the seat
has reached the desired position.
Slide the seat back or forward a little
to engage the locking mechanism.
This will set the seat depth.
A
000000XX0
36
Adjustment options
5.1.3 Backrest adjustment
•
See Fig. 000000140 (seat may differ
slightly from diagram)
The backrest is continuously adjustable,
from a fully horizontal to a fully vertical
position.
The adjustment must be done as follows:
•
Pull up the handle (A) while you are
on the seat.
The backrest will now automatically
move forward.
•
Press the backrest backward by
A
leaning back to a position that is most
comfortable for you.
•
After adjustment, release the handle to secure the backrest in the position
you have chosen.
Attention:
Do not operate the handle if the seat is unoccupied, because the
backrest will come forward very powerfully.
The backrest must be adjusted in such a way that your back is
properly supported while driving.
If the backrest is tilted too far backwards, this will negatively
influence the seating stability, especially on slopes.
5.1.4 Adjusting the armrest
•
See Fig. 000000160 (seat may differ
slightly from diagram)
A
Both armrests can be flipped up
completely.
37
Adjustment options
Adjust the armrest width as follows:
The armrest adjustment knobs are located at
the rear of the seat.
To loosen armrest, turn the knob counterclockwise.
After selecting the new width, re-tighten knobs
and ensure the armrests are secure.
5.1.5 Adjusting the headrest
The headrest can be adjusted to several different heights.
Adjusting the height of the head rest
Adjust the height of the head rest as follows:
•
Pull up the headrest by hand. It will engage into one of three positions with a
click.
5.2
•
Adjusting the steering tiller
See Fig. 000000130.
The steering tiller can be adjusted as
follows:
•
Pull handle (A) down with one hand,
while at the same time pulling the
steering tiller towards you with the
other, until the most comfortable
position is reached.
•
Release the handle in the chosen
position. Then, release the steering
tiller.
If you release the steering tiller while still
holding up the handle, the gas-springloaded steering tiller will move to its most forward position.
A
000000130
Use caution when adjusting the steering tiller to avoid getting your
fingers pinched.
38
Maintenance
6 Maintenance
XXXXXX-01010700000-nl.doc
6.1
Maintenance table
Everything that is used should be maintained. This is also true for a scooter.
For trouble-free use of the scooter, it should be regularly serviced by your
dealer.
Below, we have indicated what needs to be checked, how often this should be
done, and by whom.
Time
Daily
Weekly
Monthly
Every three
months
•
•
•
•
•
•
Description
Charging of the batteries after each full day of
use
Checking the tire pressure
Checking for oil leakage underneath the scooter
Cleaning of the scooter (see cleaning procedure)
Cleaning of the upholstery (if necessary)
Lubricating the turning system of the seat:: to do
this, the seat must be removed. See 'Removing
the seat'. Lithium grease is recommended.
User
X
X
X
X
X
X
It is recommended to have your scooter serviced by your dealer at least once
a year, or, in case of intensive use, once every six months.
In principle, we recommend you let your dealer do all maintenance work. The
maintenance activities you can perform yourself are indicated in the table
above.
If you discover any oil leakage underneath the scooter,
immediately contact your dealer. Do not drive the scooter.
6.1.1
Batteries
For maintenance see the following documentation:
• Regulations concerning the batteries.
• User manual for the battery charger, or the instructions on the
battery charger.
The scooter has gel batteries. These batteries are entirely sealed and
maintenance free.
39
Maintenance
A sticker shows the connection diagram of the batteries. This sticker is placed
on the inside of the cover of the battery compartment.
• Make sure that the batteries are always well charged.
• Do not use the scooter if the batteries are almost depleted. This
may damage the batteries and you run the risk of coming to an
unintended stop.
• The use of 'wet' batteries is not permitted. If the batteries must be
replaced, gel batteries must be used.
6.1.2 Replacing the batteries
If the capacity of the batteries is reduced
to the extent that the scooter can only
make very short trips, or even none at
all, the batteries are at the end of their
life span. Replace them as soon as
possible.
Contact your dealer: he
knows exactly which
batteries are most suitable
for your scooter.
A
Replace the batteries as follows:
Switch off the scooter (remove the
contact plug from the contact).
•
Remove the seat. See 'Removing the
seat’.
•
Remove the lock (A) from the front of
the battery cover.
•
•
•
•
•
40
D C B A C
Remove the red and the black plugs
from the battery (A).
Loosen the taut-bands, which hold
the batteries, by squeezing in the
clasps (B).
C
Loosen the battery clamps (C) from
the cables using a spanner with a key width of 13 mm.
Remove both batteries (D).
B
C A D
Maintenance
New batteries are placed in the reverse order, as follows:
•
Put the new batteries in place.
•
Fasten the batteries using the taut-bands.
•
Connect the cables according to the table below:
No.
B
Cable colour
Black
Text on label
Battery 1
C
D
Red
Black
Battery 1
Battery 2
E
Red
Battery 2
•
Connect to
Minus terminal of battery 1
(left)
Plus terminal of battery 1 (left)
Minus terminal of battery 2
(right)
Plus terminal of battery 2
(right)
Tighten the battery clamps.
• Note the correct connection of the cables to the batteries: these
are marked with labels.
• The connections may NOT be exchanged.
• Make sure that the battery terminals and battery clamps are quite
clean.
•
•
Grease the battery clamps to prevent oxidation, using acid-free Vaseline.
Replace the cover.
• As soon as the new batteries are placed, the batteries must be
charged. See ‘Charging the batteries’.
• Avoid metal parts from coming into contact with the battery
terminals. This may lead to short circuiting, which could have very
serious consequences.
• See ‘Used scooters and the environment’ for correct disposal of
the batteries.
6.1.3 Cleaning the batteries
Gel batteries are maintenance free. Still, you have to pay attention to the
following matters:
•
Keep the batteries clean and dry: dirt and water may cause a leak, causing
the capacity of the batteries to decrease.
•
Cleaning the terminals: and after cleaning, grease them with acid-free
Vaseline.
Never completely deplete the batteries! This can seriously
damage the batteries and considerably decrease their life span.
41
Maintenance
6.2
Tires
For the proper functioning of the scooter it is very important that the tires are
kept at the correct pressure.
6.2.1.
Inflating the Tires
The tires are equipped with a car valve. You can have the tires inflated at your
dealer or local gas service station, or you can do it yourself using a foot or
hand pump. To inflate the tires, remove the cap from the valve. Under-inflated
tires can reduce the range of the scooter and increase the wear on the tire
treads. For the correct tire pressure, see ‘Product specifications’.
When inflating the tires, never exceed the maximum
recommended tire pressure. This value is indicated on the tire
itself.
For inspection of the tires, see the 'maintenance table'.
After inflating the tires, always make sure to replace the cap back
on the valve, to avoid dirt and sand entering the valve.
42
Maintenance
6.3
Cleaning Procedures
Removing dry dirt
Upholstery, metal parts and frame parts can usually be cleaned easily with a
dry soft cloth.
Removing mud and/or other wet dirt
Parts that are soiled with wet dirt can best be cleaned by first wiping the dirty
parts with a damp cloth and then wiping them dry with a dry soft cloth.
Upholstery
Clean with a damp cloth. After removing the dirt, the cleaned parts should be
wiped dry with a soft dry cloth.
• Never use abrasive or aggressive cleansers. They can damage
the scooter.
• Also do not use organic solvents such as thinner, dry-cleaning
naphtha, or white spirit.
• Do not spray or pour water on scooter.
• Be careful with water near the electronic system.
• Upholstery: do not dry clean, iron or spin dry.
EBAXXX-010704000-en.doc
43
Troubleshooting
7 Troubleshooting
If your Fortress Winner will not function, even though the batteries are fully
charged, check the following points before getting in touch with your dealer.
1.
2.
3.
Check that all battery clamps are securely in place.
Check the free wheel lever to ensure it is in the BRAKE ENGAGE position
(not in free wheel position).
Check if the automatic circuit breaker has jumped out. If it has, reset the
circuit breaker by pushing it in.
If it jumps out again, contact your dealer.
7.1
Troubleshooting table
If your scooter will not drive, or does not drive as it should, please check the
list below first, to see if you can solve the problem yourself, before
approaching the dealer.
Possible cause
Action
Action to
be taken
by
The jack key is not properly
inserted into the jack key
receptacle.
The connectors in the motor
compartment are not plugged
into the controller properly, or
they are loose.
The battery clamps are not
fastened properly.
The scooter is in free wheel
position.
•
Put the jack key into the
receptacle properly.
Yourself
•
Check the connectors and
make sure they are
plugged into the controller
properly.
Check the battery clamps.
Dealer
•
The automatic circuit breaker
has jumped out.
•
•
•
There is a loose connector.
•
•
•
•
•
44
•
•
Yourself
Move the free wheel lever Yourself
into the BRAKE ENGAGE
position, then remove and
re-insert the jack key to
reset the scooter..
See ‘Circuit breaker’
Yourself
Push the automatic circuit
breaker back in and reset
scooter with jack key.
Correct the connection if
Yourself
possible, otherwise contact
+
your dealer.
Dealer
Troubleshooting
Possible cause
•
The battery voltage is too low.
Action
•
•
•
•
The scooter drives too slowly.
•
•
Overheated motor.
•
Check the battery voltage.
See ‘Battery condition
meter’.
Charge the batteries for 8
hours.
Check operation of the
battery charger.
Turn the speed controller
up (by turning it to the
right).
Allow the scooter to cool
down.
Action to
be taken
by
Yourself
Yourself
Yourself
Sometimes simply switching the scooter off and back on again will correct the
problem.
If you cannot solve the problem by using the list above, contact your dealer.
45
Troubleshooting
7.2
•
Automatic circuit breaker
See Fig. 000000180.
The scooter has been equipped with an
automatic circuit breaker (A).
In normal circumstances, the automatic
circuit breaker will not pop out and the
scooter will be ready for use.
When the electric circuit is overloaded or
shorted, the automatic circuit breaker will
switch off the electric system to prevent
damage.
Overload can be caused if the motor is
overheated. If the automatic circuit
breaker switches off the electric circuit of
the scooter, it will pop out.
A
000000180
The automatic circuit breaker is located on the rear cover under the seat.
By pressing the automatic circuit breaker back in again, you can try to restart
the scooter. If the automatic circuit breaker pops out again, wait 15 to 20
minutes to allow the motor to cool off, then try resetting again.
If you are able to restart the scooter after this, you may drive on. Make sure,
however, to avoid obstacles and hills.
If the automatic circuit breaker pops out again after the motor was
allowed to cool off, there may be a short circuit. In this case, do
not attempt driving, but contact your dealer.
46
Troubleshooting
7.3
Electro-magnetic Interference (EMI) malfunction
Radio waves may negatively influence the drive of an electric scooter. The
scooter itself may disrupt the operation of electromagnetic fields, such as
those used in alarm systems and shop circuitry.
Sources of radio waves, such as radio and TV stations, amateur radio
transmitters, elevators, transmitters, stereo radios, and mobile telephones may
influence electric wheelchairs and scooters.
The warnings listed below are intended to avoid the risk of unintended freewheeling of the electric scooter, which may result in serious injuries.
1. Do not switch on manual items for personal communication, such as
radios and mobile telephones, while the electric scooter is switched on.
2. Avoid transmitters, such as radio and TV stations, in the neighbourhood.
Do not get too close.
3. If any unintended movements should occur, or if the brake is moved to its
neutral position, switch off the electric wheelchair or scooter by pulling the
contact plug from the contact.
4. Be aware of the fact that any accessories or components that are installed,
or any alterations that are made to the scooter, may increase the influence
of radio waves.
Remarks:
There is no easy way to test the effects of radio waves on the general
immunity of the electric wheelchair or scooter.
5. Notify your dealer, or the manufacturer of the scooter, of all cases of
unintended movements or switching to neutral. Indicate whether there is
any source of radio waves in the neighbourhood.
Remarks:
The immunity level of the Fortress Winner is 20 Volts/meter.
47
Technical specifications
8 Technical specifications
8.1
Product specifications Fortress Winner
Manufacturer:
8.1.1
Fortress Winner
Model
Maximum user's weight
Description
Total length
Total width
Total weight incl. batteries (Grp 27)
Total weight excl. batteries
Weight of heaviest part
Static stability downward Fortress Winner
Static stability upward Fortress Winner
Static stability sideways Fortress Winner
Energy consumption: theoretic maximum
distance Fortress Winner
Dynamic stability on slopes Fortress
Winner
Climbing capacity for obstacles
Maximal speed forward
Maximal speed forward: Alpine Drive
Min brake distance from max speed
Seat angle
Seat depth
Seat width
Seat height (to floor pan)
Back height
Armrest height
48
Handicare
Vossenbeemd 104
NL-5705 CL HELMOND
the Netherlands
Fortress Winner 3 Wheel /
Fortress Winner 4 Wheel
350 lbs (159 kg)
Fortress Winner Fortress Winner
3W
4W
55” (1410 mm)
55” (1410 mm)
26½” (673 mm)
26½” (673 mm)
337 lbs (153 kg) 348 lbs (158 kg)
205 lbs (93 kg)
216 lbs (98 kg)
119 lbs (54 kg)
130 lbs (59 kg)
> 15°
> 15°
> 15°
> 15°
> 15°
> 15°
30 miles (50 km) 30 miles (50 km)
> 10°
> 10°
3.9” (100 mm)
3.9” (100 mm)
15 km/h(9.3 mph) 15 km/h(9.3mph)
9 km/h (5.5 mph) 9 km/h (5.5 mph)
139¾”
139¾”
(3,550 mm)
(3,550 mm)
2°
2°
19¾” (500 mm)
19¾” (500 mm)
19¾” (500 mm)
19¾” (500 mm)
18”, 19”, 20”
18”, 19”, 20”
(460-520 mm)
(460-520 mm)
19” (480 mm)
19” (480 mm)
9” (230 mm)
9” (230 mm)
Technical specifications
Description
Minimum radius
Capacity to drive over obstacles
Ground clearance
Turning space
Fortress Winner
3W
55” (1400 mm)
3.9” (100 mm)
4½” (114 mm)
78¾”<2000 mm
Fortress Winner 4W
75” (1905 mm)
3.9” (100 mm)
4½” (114 mm)
78¾”<2000 mm
Test data
Weight test dummy
350 lbs (160 kg)
Operating force
Operating-handle power
Resetting automatic fuse (circuit breaker)
Electronic switches
Inserting charging plug
Diameter front wheel (3 wheel)
Diameter front wheel (4 wheel)
Diameter rear wheels
Tire pressure 4 wheels, front
Tire pressure 4 wheels, rear
Tire pressure 3 wheels, front
Tire pressure 3 wheels, rear
Batteries
Maximum dimensions batteries
Fits up to Grp 27
Battery capacity
Maximum permissible charging
voltage (per battery)
Connector type
< 60 N
< 60 N
< 15 N
< 60 N
Technical data
12½ " x 4¼” (310 x 108 mm)
11½ " x 4¼” (292 x 108 mm)
12½” x 4¼” (310 x 108 mm)
50 psi
50 psi
3.5 psi
50 psi
Fortress Winner
Fortress Winner 4W
3W
12¾” x 6.9” x 8½” 12¾” x 6¾” x 8½”
324 x 175 x 213 mm 324 x 175 x 213 mm
80 Ah/20h
80 Ah/20h
13.6 V
13.6 V
A DIN 72311
A DIN 72311
49
Technical specifications
8.2
Approval
The product meets the following standards:
1. NEN-EN 12182 Technical tools for the handicapped - General standards
and testing methods October 1997.
2. NEN-EN 12184 Electrically driven wheelchairs, scooters and associated
charging equipment - Standards and testing methods April 1999.
3. The Fortress Winner scooter is classified according to EN12184 in
class C.
4. ISO 7176-8 Requirements and test methods for impact, static, and fatigue
strength July 1998.
5. ISO 7176-9 climate tests for electric wheelchairs and scooters.
6. ISO 7176-14 Standards and test methods for controller systems of
electrically driven wheelchairs 1997.
7. ISO 7176-16 Requirements of resistance to fire May 1997.
50
Technical specifications
Authorized service and technical support
If you have any problems or questions concerning this product, please contact
your dealer.
For information about a dealer in your area, contact Handicare Canada:
Canadian Office:
Handicare
355 Norfinch Drive
TORONTO ON M3N 1Y7
Canada
Manufacturer:
Handicare
Vossenbeemd 104
NL-5705 CL HELMOND
the Netherlands
XXXXXX-011000000-nl
51
Winner
Serial #:
Model:
Colour:
Date:
Dealer stamp
Tel: (416) 739-8333 * 1-800-514-7061
Fax: (416) 739-6622 * 1-888-251-9187
E-mail: [email protected]
www.handicare.ca
">