Directechs HKHT1 Installation Manual

INSTALLATION GUIDE
HKHT1
Designed by Installers for Installers
© 2020 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
2020-03-03
Directed Digital
Solutions
Contents
Warning! Safety first........................................................................................................................ 3
Introduction..................................................................................................................................... 4
Pre-installation and application warnings...................................................................................... 4
Vehicle application guide............................................................................................................ 5
Wiring connections.......................................................................................................................... 6
Main power harness (H1), 12-pin thick gauge connector................................................................ 6
Auxiliary output harness (H2), 16-pin black connector.................................................................... 6
Analog harness (H3), 18-pin white connector................................................................................ 7
MC501 harness (H4), 8 thick-gauge wires (optional)...................................................................... 7
Installation (wiring diagrams & vehicle wiring reference charts)............................................................. 8
Type 1...................................................................................................................................... 8
Type 2.................................................................................................................................... 11
Type 3 without OEM alarm........................................................................................................ 13
Type 3 with OEM alarm............................................................................................................ 14
Type 4 without OEM alarm........................................................................................................ 17
Type 4 with OEM alarm............................................................................................................ 18
Type 5 without OEM alarm........................................................................................................ 21
Type 5 with OEM alarm............................................................................................................ 22
Type 6 without OEM alarm........................................................................................................ 25
Type 6 with OEM alarm............................................................................................................ 26
Type 7 without OEM alarm........................................................................................................ 28
Type 7 with OEM alarm............................................................................................................ 29
Type 8.................................................................................................................................... 33
Type 9.................................................................................................................................... 35
Type 10.................................................................................................................................. 37
Connecting the module................................................................................................................... 39
Important!............................................................................................................................... 39
Manual or automatic transmission selection................................................................................. 39
Optional sensors...................................................................................................................... 39
RF Systems.............................................................................................................................. 40
When used in conjunction with SmartStart................................................................................... 40
Module programming............................................................................................................... 41
Method 1 - With HS CAN & FT CAN connections & with transponder immobilizer........................ 41
Method 2 - Without FT CAN & with HS CAN connections & with transponder immobilizer............. 42
Method 3 - With HS CAN & FT CAN connections & without transponder immobilizer.................... 43
Method 4 - Without FT CAN & with HS CAN connections & without transponder immobilizer........ 44
LED diagnostics and troubleshooting........................................................................................... 45
Soft reset................................................................................................................................. 47
Hard reset............................................................................................................................... 47
Learning the Tach (not needed with Virtual Tach)................................................................................ 48
Initializing Virtual Tach (not needed with hardwired or data tach applications)...................................... 48
Limited lifetime consumer warranty................................................................................................... 49
Quick Reference Guide................................................................................................................... 50
Warning! Safety first
•
•
The
•
•
•
•
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
Never use a test light or logic probe when installing this unit. Always use a multimeter.
Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must
be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from
children all remote controls to assure that the system does not unintentionally remote start the vehicle.
USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.
3
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Introduction
The HKHT1 firmware for Directed Digital Solutions is compatible with specific Hyundai and Kia vehicles. It
is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide
provides information on the installation of the module using HKHT1. If you would prefer using this system as a
digital solution, go to www.directechs.com and search for the make, model and year of the vehicle. This will
allow you to find the proper firmware and corresponding installation guide.
Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the
Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module
using the XKLoader.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Š
Š
Š
Keys required for
programming
1
Keys required for
operation
0
Important! If your vehicle is NOT equipped with transponder immobilizer AND also does not use CAN's connections, then
please flash your module with an analog firmware.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
Refer to the "Vehicle wiring reference chart" following each installation type.
General notes: This section highlights important information for this specific firmware.
[1]
[2]
[3]
[4]
[5]
[6]
The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
The siren is ONLY required when enabling the security features during module flashing.
The Green wire is ONLY required for starter disable and antigrind applications.
EMS COM connections ONLY needed if vehicle has a transponder immobilizer.
Required ONLY if RAP Off does not operate over data.
Factory Disarm Output is required ONLY if the vehicle is equipped with an OEM alarm.
Additional parts required (maximum required):
87
4 x6A
1ADiode
Diodes
86
87a
85
30
Resistor 100Ω
0 x Resistor
Fuse 7.5A
1 x 15A Fuse
0 x Relay
4
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle application guide
1
1
1
1
1
1
3
7
3
1
3
3
7 7 7
8 8 8 8 8 8
17 16 15 14 13 12 11 10 09 08
4 4 4 4
4 4 4
10 10
1 1 1 1 1
7 7 7
2 2 2 2
3 3 3 3 3
5 5 5 5 5
4 4 4 4
8 8 8 8 8 8
9 9 9
9 9 9
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ST-Brake Status (foot brake)
SS-Factory Alarm Trigger Monitoring
SS-Entry Monitoring Trunk/Hatch Pin
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring ALL Door Pins
RS-Tach / RPM Output
RS-SmartStart
3
3
7
3
1
•
RS-Remote Start Takeover
3
7
3
1
RS-RAP Shut Down (Retained ACC Power)
7
FOB-Control of aftermarket alarm with OEM
remote
7
DL-Trunk / Hatch Release
7
•
•
•
•
•
•
•
•
•
•
•
DL-Driver Priority Unlock
2
DL-Door Unlock
2
ST-E-Brake Status
1
2
ST-Door Locks Status
1
2
1
DL-Door Lock Control
6
DL-Disarm Factory Security
6
DL-Arm Factory Security
2012
6
2008
2013
6
2009
2014
6
2010
2015
6
2011
2016
Hyundai
Accent
Accent
Elantra
Elantra
Elantra Coupe
Elantra Touring
Genesis Coupe
Santa Fe
Sonata
Sonata
Tucson
Kia
Forte
Forte5
Magentis
Optima
Optima
Rio
Rondo
Sorento
Soul
Sportage
Sportage (4-cylinder)
Sportage (V6)
2017
Vehicles
PK-Immobilizer Bypass-Data No Key Req'd
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Legend:
PK: Transponder & Immobilizer Override
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
5
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wiring connections
The wiring connections listed below are specific to this firmware.
Main power harness (H1), 12-pin thick gauge connector
Conn./Pin
Color
Description
H1/1
White
Relay 3 COM – No Connection
1
H1/2
White/Brown
Relay 3 N.O. – No Connection
1
H1/3
Brown/Red
Relay 2 N.O. – No Connection
H1/4
Yellow/Red
Relay 2 COM – Lock Detection Interrupt (vehicle side)
H1/5
Orange/Red
Relay 2 N.C. – Lock Detection Interrupt (connector side)
H1/6
Yellow
Relay 1 COM – EMS COM Data (Vehicle side) 1
H1/7
White
Relay 3 COM – No Connection
1
H1/8
White/Brown
Relay 3 N.O. – No Connection
1
H1/9
Black
(-) Ground
H1/10
Red
(+) 12 Volt (Battery)
H1/11
Orange/Yellow
Relay 1 N.C. – EMS COM Data (connector side) 1
H1/12
Brown
Relay 1 N.O. – No Connection
1
Auxiliary output harness (H2), 16-pin black connector
Conn./Pin
Color
Description
H2/1
Violet/Brown
No Connection
H2/2
Yellow/Black
EMS COM Data (Connector side)
H2/3
Orange/Black
EMS COM Data (Vehicle side)
H2/4
Tan
HS CAN Low
H2/5
Tan/Black
HS CAN High
H2/6
Light Green
No Connection
H2/7
Orange/Green
FT CAN High
H2/8
Orange/Brown
FT CAN Low
H2/9
Violet/Green
No Connection
H2/10
Green/Black
(-) Parking Light Output 2
H2/11
White/Violet
(-) RAP Off Output 2
H2/12
White/Red
No Connection
H2/13
Lt. Blue/Black
(-) Disarm Output 2
H2/14
Green/Red
No Connection
H2/15
N/A
No Connection
H2/16
Violet/Yellow
No Connection
1.
2.
6
2
2
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Analog harness (H3), 18-pin white connector
Conn./Pin
Color
Description
H3/1
Lt. Blue/Red
No Connection
H3/2
Black/White
(-) Parking Brake Input (Manual Transmission)
H3/3
Gray
(-) Hood Input
H3/4
N/A
No Connection
H3/5
Gray/Black
(+) Glow Plug Input
H3/6
Violet/White
(AC) Tach Input
H3/7
Dark Blue
(-) Unlock Output 1
H3/8
Brown/Black
(-) Horn
H3/9
Red/White
(-) Trunk Release Output 1
H3/10
White/Green
No Connection
H3/11
Yellow/Green
(+) Door Input
H3/12
Blue/Red
No Connection
H3/13
Light Blue
(-) Trunk Trigger Input
2
2
2
2
1
2
2
2
H3/14
Pink/Yellow
(-) Activation (Start Trigger) Input
H3/15
Dark Green
(-) Lock Output 1
H3/16
Brown/White
(+) Brake Input 2
H3/17
Brown
(+) Siren Output 1
H3/18
Blue/White
(-) Ground When Running (Status) Output
1
MC501 harness (H4), 8 thick-gauge wires (optional)
Conn./Pin
Color
Description
H4/1
Pink/White
(+) Ignition 2/Flex Relay Output 3
H4/2
Red/White
(+) Fused (30A) Ignition 2/Flex Relay Input
H4/3
Pink
(+) Ignition Output (Also Input to Yellow in Ribbon Cable)
H4/4
Red
(+) 12 Volt (Battery) Input
H4/5
Orange
(+) Accessory Output
H4/6
Red
(+) 12 Volt (Battery) Input
H4/7
Green
Starter Input (From Key Switch) 4
H4/8
Violet
(+) Starter Output (To Starter)
1.
2.
3.
4.
7
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a
list of compatible features.
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
The Green wire is only required for starter disable and anti-grind applications.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Installation (wiring diagrams & vehicle wiring reference charts)
Type 1
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
2 - EM11, White 58-pin connector 3 - EM11, White 43-pin connector
1 - EM11, White 55-pin connector
41
10
OBDII Diagnostic
OR
(connector side view)
).
10
OR
12
C-CAN High: pin 6
1
8
9
16
The EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
Connector
Refer to the Vehicle wiring reference chart for
the connector, pin and wire color for your specific vehicle.
Cut
C-CAN Low: pin 14
Ignition Switch
(white 6-pin connector)
(+)Accessory:Orange, pin 2
Immobilizer Data Interrupt (vehicle side): Yellow/Black: 2
(+)12V: Green,
pin 1
Immobilizer Data Interrupt (connector side): Orange/Black: 3
HS CAN Low: Tan: 4
(+)Starter:
Yellow, pin 3
(+) Ignition:
Pink,
pin 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Parking Lights Output: Green/Black: 10
(+) Starter Output
(to starter): Violet
(+) Accessory Output: Orange
MC501
7 White
(+) 12V Input: Red
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
B-CAN Wires & Parking Lights
Refer to the Vehicle wiring
reference charts for the
connector, pin and wire color
in your vehicle.
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
11: Orange/Yellow:
Immobilizer Data Interrupt
(vehicle side)
(+) Ignition Output (also input
to Yellow wire in ribbon
cable): Pink
(-) Hood Input: Gray: 3
10: Red: (+) 12V
(+) 12V
9: Black: (-) Ground
Hood Pin
(+) Siren Output: Brown: 17
6: Yellow:
Immobilizer Data Interrupt
(connector side)
Siren
8
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
Locating components in the
www.directechs.com
for vehicle
additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Elantra 2011-2013
12V
Green
1
(+)
Ignition switch.
White
6
A
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
2
(-)
Headlight switch.
White
10
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
White/Orange or Brown
13
Data
Junction Box (Rear), I/P-G.
White
24
D
B-CAN Low
Yellow/Orange or White
EMS COM
Blue or Blue/Orange
1
Data
Junction Box (Rear), I/P-G.
White
24
D
10
Data
Driver kick panel, EM11.
White
55
E
1
(+)
Ignition switch.
White
6
A
Hyundai Elantra 2014-2016
12V
Green
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
2
(-)
Headlight switch.
White
10
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
Green or Brown
13
Data
Junction Box (Rear), I/P-G.
White
24
D
B-CAN Low
Orange or White
EMS COM
Blue
1
Data
Junction Box (Rear), I/P-G.
White
24
D
12
Data
Driver kick panel, EM11.
White
58
E
1
(+)
Ignition switch.
White
6
A
Hyundai Elantra Coupe 2013
12V
Green
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
2
(-)
Headlight switch.
White
10
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
White/Orange or Brown
13
Data
Junction Box (Rear), I/P-G.
White
24
D
B-CAN Low
Yellow/Orange or White
1
Data
Junction Box (Rear), I/P-G.
White
24
D
EMS COM
Blue
10
Data
Driver kick panel, EM11.
White
55
E
9
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Elantra Coupe 2014
12V
Green
1
(+)
Ignition switch.
White
6
A
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
2
(-)
Headlight switch.
White
10
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
Green or Brown
13
Data
Junction Box (Rear), I/P-G.
White
24
D
B-CAN Low
Orange or White
1
Data
Junction Box (Rear), I/P-G.
White
24
D
EMS COM
Blue
10
Data
Driver kick panel, EM11.
White
55
E
Hyundai Sonata 2011-2014
12V
Green
1
(+)
Ignition switch.
White
6
A
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
2
(-)
Headlight switch.
White
10
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
White/Orange or Blue
12
Data
Junction Box (Rear), I/P-F.
White
24
D
B-CAN Low
Yellow/Orange
11
Data
Junction Box (Rear), I/P-F.
White
24
D
EMS COM
Blue or Blue/Black
10
Data
Driver kick panel, EM11.
White
43
E
Kia Optima 2011-2013
12V
Green
1
(+)
Ignition switch.
White
6
A
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
1
(-)
Headlight switch.
White
13
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
White/Orange
25
Data
Junction Box (Rear), I/P-E.
White
39
D
B-CAN Low
Yellow/Orange
38
Data
Junction Box (Rear), I/P-E.
White
39
D
EMS COM
Blue
10
Data
Driver kick panel, EM11.
White
43
E
1
(+)
Ignition switch.
White
6
A
Kia Optima 2014-2015
12V
Green
Accessory
Orange
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Yellow
3
(+)
Ignition switch.
White
6
A
Parking Lights
Pink
1
(-)
Headlight switch.
White
13
C
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
B-CAN High
White/Orange
13
Data
Junction Box (Rear), I/P-G.
White
24
D
B-CAN Low
Yellow/Orange
EMS COM
Blue
10
1
Data
Junction Box (Rear), I/P-G.
White
24
D
41
Data
Driver kick panel, EM11.
White
58
E
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 2
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - EM01, Black or Blue 39-pin connector
15
2 - EM01, Gray 39-pin connector
OR
The EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
OBDII Diagnostic
(connector side view)
).
Refer to the Vehicle wiring reference chart for
the connector, pin and wire color for your specific vehicle.
15
Connector
Cut
C-CAN High: pin 6
1
8
9
16
Immobilizer Data Interrupt (vehicle side): Yellow/Black: 2
Immobilizer Data Interrupt (connector side): Orange/Black: 3
C-CAN Low: pin 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
Note: program
for double
pulse when
flashing.
(+) Starter Output
(to starter): Violet
(+) Ignition Output:
Pink
7 White
(+) 12V Input: Red
MC501
Hood Pin
(-) Hood Input: Gray: 3
(-) Unlock Output: Dark Blue: 7
(-) Lock Output: Dark Green: 15
(+) Starter
White,
pin 1
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
4 White
(+) 12V Input: Red
(+) Accessory Output:
Orange
8 thick-gauge wires
Starter Input (from
key switch): Green
(-) Disarm Output: Lt. Blue/Black: 13
(+) Accessory
Orange,
pin 3
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
11: Orange/Yellow:
Immobilizer Data Interrupt
(connector side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow:
Immobilizer Data Interrupt
(vehicle side)
Siren
(+) 12V: Green,
pin 5
(+) Ignition: Pink, pin 6
Ignition Switch
(white 6-pin connector)
11
Refer to the Vehicle
wiring reference charts
for pin, wire and
connector details
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Locating wiring
components
in the vehicle
Vehicle
reference
chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Connector Information
Color
Pin
Polarity
Location
12V
Green
5
(+)
Ignition switch.
Accessory
Orange
3
(+)
Ignition switch.
Ignition
Pink
6
(+)
Starter
White
1
(+)
EMS COM
Blue/Black
15
C-CAN High
Red
6
C-CAN Low
Blue
Parking Lights
Red or Pink/
Black
Lock
Blue
Unlock
Factory Alarm Disarm
Color
Pins
Ref.
White
6
A
White
6
A
Ignition switch.
White
6
A
Ignition switch.
White
6
A
Data
Left of dash fuseb box, EM01.
Black
39
E
Data
OBDII.
Black
16
B
14
Data
OBDII.
Black
16
B
10
(-)
Drivers kick panel.
Blue
20
D
6
(-)
Dash fuse box.
White
16
E
Yellow/Black
16
(-)
Dash fuse box.
White
16
E
White/Black
(driver door key
unlock)
33
double (-)
Blue
41
D
Hyundai Accent 2008-2011
Drivers kick panel.
Drivers Door
Green
2
(-)
Drivers kick panel.
Blue
42
D
Brake
Green
2
(+)
Dash fuse box.
Gray
18
E
12V
Pink
5
(+)
Ignition switch.
White
6
A
Accessory
Orange
3
(+)
Ignition switch.
White
6
A
Ignition
Pink
6
(+)
Ignition switch.
White
6
A
Starter
White
1
(+)
Ignition switch.
White
6
A
EMS COM
Blue/Black
15
Data
Right of dash fuse box, EM01
Gray
39
E
C-CAN High
Red
6
Data
OBDII.
Black
16
B
C-CAN Low
Blue
14
Data
OBDII.
Black
16
B
Parking Lights
"Pink/Black
(without BCM)
Red (with
BCM)"
14
(-)
Headlight switch.
Blue
20
C
Lock
Blue
6
(-)
Dash fuse box.
White
16
E
Unlock
Yellow/Black
16
(-)
Dash fuse box.
White
16
E
Factory Alarm Disarm
White/Black
(driver door key
unlock)
33
double (-)
Drivers kick panel.
Green
33
D
Kia Rio 2008-2011
Drivers Door
Green
2
(-)
Drivers kick panel.
Green
42
D
Brake
Red/Orange
2
(+)
Dash fuse box.
Gray
18
E
12
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 3 without OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - EM11, Gray 39-pin connector
15
2 - MC211, Blue 24-pin connector
OR
EMS COM connections only needed
if vehicle has transponder/immobilizer.
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
OBDII Diagnostic
(connector side view)
19
).
3 - EM11, Blue 42-pin connector
18
OR
Connector
Cut
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
Immobilizer Data Interrupt (connector side): Yellow/Black: 2
Immobilizer Data Interrupt (vehicle side): Orange/Black: 3
C-CAN Low: pin 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
MC501
(+) 12V Input: Red
(+) Ignition Output:
Pink
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
Hood Pin
(-) Hood Input: Gray: 3
(-) Unlock Output: Dark Blue: 7
11: Orange/Yellow: Immobilizer Data Interrupt
(vehicle side)
10: Red: (+) 12V Input
(-) Trunk Release Output: Red/White: 9
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
(+) Accessory: Pink, pin 3
(+) Starter:
White, pin 1
Remote Start Safety
Override Switch
(+) Ignition :
Blue, pin 6
9: Black: (-) Ground
6: Yellow: Immobilizer Data Interrupt
(connector side)
Siren
(+) 12V: Orange, pin 5
Ignition Switch
(6-pin connector)
13
Refer to the Vehicle
wiring reference chart.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 3 with OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - EM11, Gray 39-pin connector
15
2 - MC211, Blue 24-pin connector
OR
EMS COM are connections only needed
if the vehicle has transponder/immobilizer.
OBDII Diagnostic
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
(connector side view)
19
).
3 - EM11, Blue 42-pin connector
18
OR
Connector
Cut
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
Immobilizer Data Interrupt (connector side): Yellow/Black: 2
Immobilizer Data Interrupt (vehicle side): Orange/Black: 3
C-CAN Low: pin 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
(-) Disarm Output: Lt. Blue/Black: 13
(+) 12V Input: Red
(+) 12V Input: Red
MC501
7 White
(+) Accessory Output:
Orange
8 thick-gauge wires
Starter Input (from
key switch): Green
The Remote Start
Safety Override
Switch MUST be in
the ON position.
4 White
(+) Starter Output
(to starter): Violet
Hood Pin
(-) Hood Input: Gray: 3
(-) Trunk Release Output: Red/White: 9
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
(+) Accessory: Pink, pin 3
(+) Ignition :
Blue, pin 6
(+) 12V: Orange, pin 5
Ignition Switch
(6-pin connector)
14
11: Orange/Yellow: Immobilizer
Data Interrupt (vehicle side)
10: Red: (+) 12V Input
(-) Unlock Output: Dark Blue: 7
(+) Ignition Output:
Pink
(+) Starter:
White, pin 1
Remote Start Safety
Override Switch
Siren
4x
1A Diodes
9: Black: (-) Ground
6: Yellow: Immo. Data Interrupt
(connector side)
5: Orange/Red: Lock Detection Interrupt
(connector side)
4: Yellow/Red: Lock Detection Interrupt
(vehicle side)
(-) Lock Detection
(-) Factory Alarm Arm
(-) Lock
(-) Unlock
(-) Factory Alarm Disarm
Refer to the Vehicle
wiring reference chart.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Locating components in the vehicle
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Elantra Touring 2009-2012
12V
Orange
5
(+)
Ignition switch.
White
6
A
Accessory
Pink
3
(+)
Ignition switch.
White
6
A
Ignition
Blue
6
(+)
Ignition switch.
White
6
A
Starter
White
1
(+)
Ignition switch.
White
6
A
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
EMS COM
Blue/Black
15
Data
Passenger kick panel, EM11.
Gray
39
F
Parking Lights
Blue
8
(-)
Headlight switch.
White
14
C
Lock
Green
25
(-)
Drivers kick panel.
Gray
39
D
Unlock
Yellow
39
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Arm
Green
23
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Disarm
Yellow
6
(-)
Drivers kick panel.
Gray
39
D
Lock Detection
Black/Orange
2
open
Drivers kick panel.
Gray
40
D
Trunk Release
White
Drivers Door
Red
15
5
(-)
Drivers kick panel.
Gray
39
D
36
(-)
Drivers kick panel.
Gray
39
D
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Santa Fe 2008-2012
12V
Red
5
(+)
Ignition switch.
Black
6
A
Accessory
Red or Blue
3
(+)
Ignition switch.
Black
6
A
Ignition
Orange
6
(+)
Ignition switch.
Black
6
A
Starter
Green
1
(+)
Ignition switch.
Black
6
A
C-CAN High
Red/Black or Blue
6
Data
OBDII.
Black
16
B
C-CAN Low
Red or Orange
14
Data
OBDII.
Black
16
B
EMS COM
White/Orange or
White or Red
19
Data
Passenger kick panel, MC211.
Blue
24
F
Parking Lights
Blue/Orange
14
(-)
Headlight switch.
White
18
C
Lock
Blue/Black
18
(-)
Drivers kick panel.
Brown
24
D
Unlock
Gray/Black
19
(-)
Drivers kick panel.
Brown
24
D
Factory Alarm Arm
Brown/Orange
5
(-)
Drivers kick panel.
Brown
24
D
Factory Alarm Disarm
Pink
6
(-)
Drivers kick panel.
Brown
24
D
Lock Detection
Gray
Drivers Door
Green/Orange
4
open
Drivers kick panel.
Brown
24
D
N/A
(-)
Drivers kick panel harness to rear.
N/A
N/A
D
Kia Rondo 2008-2012
12V
Red or Pink
5
(+)
Ignition switch.
Black
6
A
Accessory
White or Pink
3
(+)
Ignition switch.
Black
6
A
Ignition
White/Blue or Blue
6
(+)
Ignition switch.
Black
6
A
Starter
Black/Yellow or
Green
1
(+)
Ignition switch.
Black
6
A
C-CAN High
Red
6
Data
OBDII.
Black
16
B
C-CAN Low
Blue
14
Data
OBDII.
Black
16
B
EMS COM
Brown
18
Data
Driver kick panel, EM11.
Blue
42
D
Parking Lights
Yellow
10
(-)
BCM above brake pedal.
White
26
E
Lock
White
8
(-)
Drivers kick panel.
Gray
39
D
Unlock
White/Black
9
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Arm
Gray
3
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Disarm
Brown
2
(-)
Drivers kick panel.
Gray
39
D
Lock Detection
Yellow
1
open
Drivers kick panel.
Gray
39
D
Trunk Release
Blue/Orange
18
(-)
BCM above brake pedal.
White
22
E
Drivers Door
Red
36
(-)
BCM above brake pedal.
White
22
E
16
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 4 without OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - MC12, Gray 39-pin conn.
).
2 - EM11, Blue 39-pin conn.
OBDII Diagnostic
(connector side view)
15
C-CAN High: pin 6
C-CAN wires MUST be connected for
proper operation.
1
8
Note: For the 2012-2013 Kia Soul,
HS CAN High and Low may be reversed.
9
16
The EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
Refer to the Vehicle wiring reference chart for
the connector, pin and wire color for your specific vehicle.
C-CAN Low: pin 14
10
OR
Connector
Cut
Immobilizer Data Interrupt
(connector side): Yellow/Black: 2
Immobilizer Data Interrupt
(vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
(+) Starter Output (to starter): Violet
HS CAN High: Tan/Black: 5
(+) 12V Input: Red
(+) 12V Input: Red/White
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
MC501
7 White
(+) Ignition Output: Pink
8 thick-gauge wires
(+) 12V Input: Red
(+) Accessory Output: Orange
4 White
Starter Input (from key switch): Green
(+) Accessory 2 Output:
Pink/White
(-) Hood Input: Gray: 3
(white 6-pin connector)
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
(+) Accessory:
Orange, pin 3
(+) Ignition:
Blue, pin 6
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: Immobilizer Data Interrupt
(connector side)
Siren
15A fuse
(+) Accessory Interrupt
(connector side)
(+) 12V: Black,pin 5
87
87a
86 30
85
17
11: Orange/Yellow:Immobilizer
Data Interrupt (vehicle side)
(-) Trunk Release Output: Red/White: 9
Ignition Switch
(+) Accessory 2:
Yellow, pin 4
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Hood Pin
(-) Unlock Output: Dark Blue: 7
(+) Starter:
White,
pin 1
Remote Start Safety
Override Switch
Refer to the Vehicle
wiring reference chart.
(+) Accessory Interrupt
(vehicle side)
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 4 with OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
EMS COM are connections
only needed if the vehicle has
a transponder/immobilizer.
OBDII Diagnostic
(connector side view)
C-CAN High: pin 6
C-CAN wires MUST be connected for
proper operation.
1
8
Note: For the 2012-2013 Kia Soul,
HS CAN High and Low may be reversed.
9
16
Refer to the Vehicle wiring reference
charts section for the connector, pin and
wire color in your specific vehicle.
1 - MC12, Gray 39-pin connector
15
).
2 - EM11, Blue 39-pin connector
10
OR
Connector
Cut
C-CAN Low: pin 14
Immobilizer Data Interrupt
(connector side): Yellow/Black: 2
Immobilizer Data Interrupt
(vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
(+) Starter Output (to starter): Violet
HS CAN High: Tan/Black: 5
(+) 12V Input: Red
(+) 12V Input: Red/White
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
(-) Disarm Output: Lt. Blue/Black: 13
MC501
7 White
(+) Ignition Output: Pink
8 thick-gauge wires
(+) 12V Input: Red
(+) Accessory Output: Orange
4 White
Starter Input (from key switch): Green
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Hood Pin
11: Orange/Yellow: Immo. Data
Interrupt (vehicle side)
(+) Accessory 2 Output:
Pink/White
(-) Hood Input: Gray: 3
(-) Unlock Output: Dark Blue: 7
(-) Trunk Release Output: Red/White: 9
Ignition Switch
(white 6-pin connector)
(+) Starter:
White,
pin 1
Remote Start Safety
Override Switch
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
(+) Accessory:
Orange, pin 3
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: Immo. Data
Interrupt (connector side)
5: Orange/Red: Lock Detection
Interrupt (connector side)
4: Yellow/Red: Lock Detection
Interrupt (vehicle side)
Siren
(+) Ignition:
Blue, pin 6
(+) Accessory 2:
Yellow, pin 4
4x
1A Diodes
15A fuse
(+) Accessory Interrupt
(connector side)
(+) 12V: Black,pin 5
87
87a
86 30
85
18
(-) Lock Detection
(-) Factory Alarm Arm
(-) Lock
(-) Unlock
(+) Accessory Interrupt
(vehicle side)
(-) Factory Alarm Disarm
Refer to the Vehicle
wiring reference chart.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Connector Information
Color
Pin
Polarity
Location
Color
Pins
Ref.
12V
Black
5
Accessory Interrupt
Orange
3
(+)
Ignition switch.
Black
6
A
(+)
Ignition switch.
Black
6
A
Accessory 2
Yellow
Ignition
Blue
4
(+)
Ignition switch.
Black
6
A
6
(+)
Ignition switch.
Black
6
A
Starter
White
1
(+)
Ignition switch.
C-CAN High
Black
6
Data
OBDII.
Black
6
A
Black
16
B
C-CAN Low
White
14
Data
OBDII.
EMS COM
Blue/Black
15
Data
Passenger kick panel, MC12.
Black
16
B
Gray
39
F
Parking Lights
Blue/Orange
14
(-)
Lock
Blue/Black
18
(-)
Headlight switch.
White
18
C
Drivers kick panel.
Brown
24
D
Kia Forte 2010-2013
Unlock
Green/Orange
19
(-)
Drivers kick panel.
Brown
24
D
Factory Alarm Arm
Green/Orange
23
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Disarm
Blue/Orange
6
(-)
Drivers kick panel.
Gray
39
D
Lock Detection
Black/Orange
2
open
Drivers kick panel.
Gray
39
D
Drivers Door
Green/Orange
N/A
(-)
Drivers kick panel.
N/A
N/A
D
19
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Connector Information
Color
Pin
Polarity
Location
Color
Pins
Ref.
12V
Black
5
Accessory Interrupt
Orange
3
(+)
Ignition switch.
Black
6
A
(+)
Ignition switch.
Black
6
A
Accessory 2
Yellow
Ignition
Blue
4
(+)
Ignition switch.
Black
6
A
6
(+)
Ignition switch.
Black
6
A
Starter
White
1
(+)
Ignition switch.
C-CAN High
Black
6
Data
OBDII.
Black
6
A
Black
16
B
C-CAN Low
White
14
Data
OBDII.
Black
16
B
EMS COM
Blue/Black
15
Data
Parking Lights
Orange
1
(-)
Passenger kick panel, MC12.
Gray
39
F
Headlight switch.
White
13
C
Kia Forte5 2011-2013
Lock
Blue/Black
18
(-)
Drivers kick panel.
Gray
39
D
Unlock
Green/Orange
19
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Arm
Green/Orange
23
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Disarm
Blue/Orange
6
(-)
Drivers kick panel.
Gray
39
D
Lock Detection
Black/Orange
2
open
Drivers kick panel.
Gray
39
D
Trunk Release
Blue/Black
2
(-)
Rear of dash fuse box.
White
18
E
Drivers Door
Red
36
(-)
Drivers kick panel.
Gray
39
D
Kia Soul 2010-2013
12V
White
5
(+)
Ignition switch.
Black
6
A
Accessory Interrupt
White
3
(+)
Ignition switch.
Black
6
A
Accessory 2
Yellow
4
(+)
Ignition switch.
Black
6
A
Ignition
Pink
6
(+)
Ignition switch.
Black
6
A
Starter
Blue
1
(+)
Ignition switch.
Black
6
A
C-CAN High
Red
6
Data
OBDII.
Black
16
B
C-CAN Low
Blue
14
Data
OBDII.
Black
16
B
EMS COM
Blue/Black
10
Data
Above driver kick panel, EM11.
Blue
39
G
Parking Lights
Pink
1
(-)
Headlight switch.
White
13
C
Lock
Brown
N/A
(-)
Drivers kick panel harness to rear.
N/A
N/A
D
Unlock
Green
N/A
(-)
Drivers kick panel harness to rear.
N/A
N/A
D
Factory Alarm Arm
Brown
24
(-)
Drivers kick panel.
White
26
D
Factory Alarm Disarm
Gray
13
(-)
Drivers kick panel.
White
26
D
Lock Detection
Yellow
23
open
Drivers kick panel.
White
26
D
Trunk Release
Pink
10
(-)
Passenger kick panel.
White
26
F
Drivers Door
Green
9
(-)
Passenger kick panel.
White
26
F
20
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 5 without OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - MC21, Green 18-pin connector
OBDII Diagnostic
(connector side view)
18
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
).
2 - EM11, Black or White 46-pin connector
OR
EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
15
Connector
Cut
C-CAN Low: pin 14
EMS COM Data (connector side): Yellow/Black: 2
EMS COM Data (vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
B-CAN Wires
See the Vehicle wiring reference
charts for the connector, pin and
wire color in your vehicle.
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Parking Light Output: Green/Black: 10
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
(+) 12V Input: Red
MC501
(+) Ignition Output:
Pink
Hood Pin
(-) Hood Input: Gray: 3
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
(-) Unlock Output: Dk. Blue: 7
(-) Hatch Release / Power Liftgate: Red/White: 9
(-) Lock Output: Dk. Green: 15
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
Ignition switch
(6-pin connector)
(+) Accessory: Blue, pin 2
Remote Start Safety
Override Switch
11: Orange/Yellow: EMS COM Data
(vehicle side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: EMS COM Data
(connector side)
Siren
(+) Starter: Green, pin 3
(+) 12V:
Red,
pin 1
(+) Ignition: Orange, pin 4
21
Refer to the Vehicle wiring
reference charts for wire
and connector details
related to the standard
connections in the vehicle.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 5 with OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - MC21, Green 18-pin connector
OBDII Diagnostic
(connector side view)
18
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
).
2 - EM11, Black or White 46-pin connector
15
OR
1
8
EMS COM are connections only needed
if the vehicle has transponder/immobilizer.
9
16
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
Connector
Cut
C-CAN Low: pin 14
EMS COM Data (connector side): Yellow/Black: 2
EMS COM Data (vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
B-CAN Wires
Refer to the Vehicle wiring reference
charts for the connector, pin and
wire color in your vehicle.
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
Remote Start Safety
Override Switch
(-) Parking Light Output: Green/Black: 10
(-) Disarm Output: Lt. Blue/Black: 13
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
(+) 12V Input: Red
MC501
(+) Ignition Output:
Pink
11: Orange/Yellow: EMS COM Data
(vehicle side)
Hood Pin
(-) Hood Input: Gray: 3
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
(-) Unlock Output: Dk. Blue: 7
(-) Hatch Release / Power Liftgate: Red/White: 9
(-) Lock Output: Dk. Green: 15
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
Ignition switch
(6-pin connector)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: EMS COM Data
(connector side)
5: Orange/Red: Lock Detection Interrupt
(connector side)
4: Yellow/Red: Lock Detection Interrupt
(vehicle side)
(+) Accessory: Blue, pin 2
(+) Starter: Green, pin 3
(-) Lock Detection
Siren
4x
1A Diodes
(+) 12V:
Red,
pin 1
(-) Factory Alarm Arm
(-) Lock
(+) Ignition: Orange, pin 4
(-) Unlock
(-) Factory Alarm Disarm
22
Refer to the Vehicle wiring
reference charts for wire and
connector details related to the
standard connections in the
vehicle.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Kia Sorento 2011-2013
12V
Red
1
(+)
Ignition switch.
White
6
A
Accessory
Blue
2
(+)
Ignition switch.
White
6
A
Ignition
Orange
4
(+)
Ignition switch.
White
6
A
Starter
Green
3
(+)
Ignition switch.
White
6
A
C-CAN High
Blue
6
Data
OBDII.
Black
16
B
C-CAN Low
Red
14
Data
OBDII.
Black
16
B
B-CAN High
White
5
Data
Rear of dash fuse box.
White
16
E
B-CAN Low
Red
6
Data
Rear of dash fuse box.
White
16
E
18
Data
Passenger kick panel, MC21.
Green
18
F
2
(-)
Headlight switch.
White
13
C
EMS COM
Blue or Blue/Orange
Parking Lights
Blue
Lock
Blue/Black
4
(-)
Dash fuse box.
White
26
E
Unlock
Gray/Black
24
(-)
Dash fuse box.
White
26
E
Factory Alarm Arm
Brown/Orange
21
(-)
Drivers kick panel.
White
26
D
Factory Alarm Disarm
Pink
9
(-)
Drivers kick panel.
White
26
D
Lock Detection
Gray
26
open
Drivers kick panel.
White
26
D
Hatch Release
Yellow/Black
11
(-)
Dash fuse box.
White
26
D
Brake
Yellow or Green/Black
1
(+)
Brake pedal switch.
White
4
G
23
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Kia Sorento 2014-2015
12V
Red
1
(+)
Ignition switch.
White
6
A
Accessory
Blue
2
(+)
Ignition switch.
White
6
A
Ignition
Orange
4
(+)
Ignition switch.
White
6
A
Starter
Green
3
(+)
Ignition switch.
White
6
A
C-CAN High
White
C-CAN Low
Red
B-CAN High
B-CAN Low
6
Data
OBDII.
Black
16
B
14
Data
OBDII.
Black
16
B
White
5
Data
Rear of dash fuse box.
White
16
E
Red
6
Data
Rear of dash fuse box.
EMS COM
Blue/Orange
Parking Lights
Driver kick panel, EM11.
White
16
E
Black or
White
46
D
15
Data
Blue
2
(-)
Headlight switch.
White
13
C
Lock
Green
4
(-)
Dash fuse box.
White
26
E
Unlock
Brown/Black
5
(-)
Dash fuse box.
White
26
E
Factory Alarm Arm
Brown/Orange
10
(-)
Drivers kick panel.
White
26
D
Factory Alarm Disarm
Pink
11
(-)
Drivers kick panel.
White
26
D
Lock Detection
Gray/Orange
17
open
Drivers kick panel.
White
26
D
Power Liftgate
Gray/Black
5
(-)
Overhead console.
White
6
H
Brake
Yellow
4
(+)
Drivers kick panel.
Black or
White
46
D
24
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 6 without OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
).
EM01
(black 21-pin connector left of junction box)
11
OBDII Diagnostic
EMS COM:
Blue/Orange, pin 11
(connector side view)
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
Cut
1
8
9
16
Immobilizer Data Interrupt (vehicle side): Yellow/Black: 2
C-CAN Low: pin 14
Immobilizer Data Interrupt (connector side): Orange/Black: 3
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
(+) 12V Input: Red
MC501
(+) 12V Input: Red
7 White
(+) Accessory Output:
Orange
8 thick-gauge wires
Starter Input (from
key switch): Green
The Remote Start
Safety Override
Switch MUST be in
the ON position.
4 White
(+) Starter Output
(to starter): Violet
Remote Start Safety
Override Switch
Hood Pin
(-) Hood Input: Gray: 3
(-) Unlock Output: Dark Blue: 7
(+) Ignition Output: Pink
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
Ignition Switch
(white 6-pin connector)
11: Orange/Yellow:
Immobilizer Data Interrupt
(connector side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow:
Immobilizer Data Interrupt
(vehicle side)
(+) Accessory: Orange, pin 2
(+) Starter: White, pin 3
Siren
(+) 12V:
Green,
pin 1
(+) Ignition: Pink, pin 4
25
Refer to the Vehicle
wiring reference chart.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 6 with OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
).
EM01
(black 21-pin connector left of junction box)
EMS COM:
Blue/Orange, pin 11
11
OBDII Diagnostic
(connector side view)
Cut
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
Immobilizer Data Interrupt (vehicle side): Yellow/Black: 2
C-CAN Low: pin 14
Immobilizer Data Interrupt (connector side): Orange/Black: 3
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
(-) Disarm Output: Lt. Blue/Black: 13
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
MC501
Hood Pin
(-) Hood Input: Gray: 3
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
(+) 12V Input: Red
(-) Unlock Output: Dark Blue: 7
(+) Ignition Output:
Pink
(-) Lock Output: Dark Green: 15
(+) Siren Output: Brown: 17
Ignition Switch
(6-pin connector)
(+) Accessory: Orange, pin 2
Remote Start Safety
Override Switch
11: Orange/Yellow:
Immobilizer Data Interrupt
(connector side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: Immobilizer Data Interrupt
(vehicle side)
5: Orange/Red: Lock Detection Interrupt
(connector side)
4: Yellow/Red:
Lock Detection Interrupt
(vehicle side)
Siren
(+) Starter: White, pin 3
4x
1A Diodes
(+) 12V:
Green,
pin 1
(-) Lock Detection
(-) Factory Alarm Arm
(-) Lock
(+) Ignition: Pink, pin 4
(-) Unlock
(-) Factory Alarm Disarm
26
Refer to the Vehicle
wiring reference chart.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Accent 2012-2017
12V
Green
1
(+)
Ignition switch.
Black
6
A
Accessory
Orange
2
(+)
Ignition switch.
Black
6
A
Ignition
Pink
4
(+)
Ignition switch.
Black
6
A
Starter
White
3
(+)
Ignition switch.
Black
6
A
C-CAN High
Green
6
Data
OBDII.
Black
16
B
C-CAN Low
Orange
14
Data
OBDII.
Black
16
B
11
Data
Dash Fuse Box
Black
21
E
7
(-)
Headlight switch.
White
14
C
EMS COM
Blue/Orange
Parking Lights
Pink/Black or Orange
Lock
Brown (w/BCM)
15
(-)
Drivers kick panel.
White
39
D
Unlock
Gray (w/BCM)
13
(-)
Drivers kick panel.
White
39
D
Lock2
w/o BCM
N/A
N/A
w/o BCM: add actuator in driver door.
N/A
N/A
N/A
Unlock2
w/o BCM
N/A
N/A
w/o BCM: add actuator in driver door.
N/A
N/A
N/A
Factory Alarm Arm
Brown (w/BCM)
15
(-)
Drivers kick panel.
White
39
D
Factory Alarm Disarm
Gray/Orange or
Green/Orange (w/
BCM)
12
(-)
Drivers kick panel.
White
39
D
Lock Detection
Black/Orange
38
open
Drivers kick panel.
White
40
D
Drivers Door
Brown/Orange
2
(-)
Drivers kick panel.
White
39
D
27
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 7 without OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - EM01, Blue 39-pin connector
OBDII Diagnostic
15
(connector side view)
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
24
3 - EM31 or EM21, White 33-pin connector
2 - EM01, Gray 39-pin connector
OR
15
EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
).
OR
21
23
Connector
Cut
C-CAN Low: pin 14
EMS COM Data (connector side): Yellow/Black: 2
EMS COM Data (vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
(+) 12V Input: Red
MC501
Hood Pin
(-) Hood Input: Gray: 3
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
(-) Unlock Output: Dk. Blue: 7
(+) Ignition Output:
Pink
(-) Lock Output: Dk. Green: 15
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
11: Orange/Yellow: EMS COM Data
(vehicle side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow: EMS COM Data
(connector side)
Ignition Switch
(6-pin connector)
(+) Starter:
Black/Yellow or
White, pin 1
(+) 12V: Black, pin 5
28
(+) Accessory:
White or Orange,
pin 3
(+) Ignition:
White/Blue or Blue,
pin 6
Siren
Refer to the Vehicle wiring
reference charts for wire
and connector details
related to the standard
connections in the vehicle.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 7 with OEM alarm
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
1 - EM01, Blue 39-pin connector
OBDII Diagnostic
15
(connector side view)
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
24
2 - EM01, Gray 39-pin connector
OR
3 - EM31 or EM21, White 33-pin connector
OR
15
EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
).
21
23
Connector
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
Cut
C-CAN Low: pin 14
EMS COM Data (connector side): Yellow/Black: 2
EMS COM Data (vehicle side): Orange/Black: 3
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
Remote Start Safety
Override Switch
(-) Disarm Output: Lt. Blue/Black: 13
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
(+) 12V Input: Red
MC501
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
11: Orange/Yellow: EMS COM Data
(vehicle side)
Hood Pin
(-) Hood Input: Gray: 3
(+) Ignition Output:
Pink
9: Black: (-) Ground
(-) Lock Output: Dk. Green: 15
6: Yellow: EMS COM Data
(connector side)
5: Orange/Red: Lock Detection Interrupt
(connector side)
4: Yellow/Red: Lock Detection Interrupt
(vehicle side)
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
Ignition Switch
(6-pin connector)
(+) Starter:
Black/Yellow or
White, pin 1
(+) Accessory:
White or Orange,
pin 3
10: Red: (+) 12V Input
(-) Unlock Output: Dk. Blue: 7
(-) Lock Detection
Siren
4x
1A Diodes
(-) Factory Alarm Arm
(-) Lock
(+) 12V: Black, pin 5
(+) Ignition:
White/Blue or Blue, pin 6
(-) Unlock
(-) Factory Alarm Disarm
29
Refer to the Vehicle wiring
reference charts for wire
and connector details
related to the standard
connections in the vehicle.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Elantra 2008-2010
12V
Black
5
(+)
Ignition switch.
White
6
A
Accessory
White or Orange
3
(+)
Ignition switch.
White
6
A
Ignition
White/Blue or Blue
6
(+)
Ignition switch.
White
6
A
Starter
Black/Yellow or
White
1
(+)
Ignition switch.
White
6
A
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
EMS COM
Blue/Black
15
Data
Passenger kick panel, EM01.
Gray
39
G
Parking Lights
Orange
8
(-)
Headlight switch.
White
14
C
Lock
Green
25
(-)
Drivers kick panel.
Gray
39
D
Unlock
Yellow
39
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Arm
Green
23
(-)
Drivers kick panel.
Gray
39
D
Factory Alarm Disarm
Yellow/Green
6
(-)
Drivers kick panel.
Gray
39
D
Lock Detection
Black/Orange
2
open
Drivers kick panel.
Gray
39
D
Trunk Release
White
5
(-)
Drivers kick panel.
Gray
39
D
Drivers Door
Red
36
(-)
Drivers kick panel.
Gray
39
D
Brake
Black
34
(+)
Drivers kick panel.
Gray
39
D
30
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Genesis Coupe 2010-2012
12V
White
5
(+)
Ignition switch.
White
6
A
Accessory
Orange
3
(+)
Ignition switch.
White
6
A
Ignition
Blue
6
(+)
Ignition switch.
White
6
A
Starter
Pink
1
(+)
Ignition switch.
White
6
A
C-CAN High
Red
6
Data
OBDII.
Black
16
B
C-CAN Low
Blue
14
Data
OBDII.
Black
16
B
EMS COM
Yellow
24
Data
Passenger kick panel, EM01
Blue
39
G
Parking Lights
White
1
(-)
Headlight switch.
White
13
C
Lock
Pink
36
(-)
Drivers kick panel.
Blue
39
D
Unlock
Orange
39
(-)
Drivers kick panel.
Blue
39
D
Factory Alarm Arm
Pink
28
(-)
Drivers kick panel.
Blue
39
D
Factory Alarm Disarm
Green
27
(-)
Drivers kick panel.
Blue
39
D
Lock Detection
Brown/Orange
29
open
Drivers kick panel.
Blue
39
D
Trunk Release
Yellow
1
(-)
Drivers kick panel.
Blue
39
D
Drivers Door
Orange
34
(-)
Drivers kick panel.
Blue
39
D
Brake
Red/Orange
2
(+)
Drivers kick panel.
White
22
D
Hyundai Sonata 2008-2010
12V
Pink
5
(+)
Ignition switch.
White
6
A
Accessory
Orange
3
(+)
Ignition switch.
White
6
A
Ignition
Blue
6
(+)
Ignition switch.
White
6
A
Starter
Green
1
(+)
Ignition switch.
White
6
A
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Yellow
14
Data
OBDII.
Black
16
B
EMS COM
Green
23
Data
Driver kick panel, EM21.
White
33
D
Parking Lights
Pink
14
(-)
Headlight switch.
White
18
C
Lock
Pink/Black
2
(-)
Drivers kick panel.
Blue
39
D
Unlock
Yellow/Black
3
(-)
Drivers kick panel.
Red
20
D
Factory Alarm Arm
Yellow
6
(-)
Drivers kick panel.
Gray
24
D
Factory Alarm Disarm
Orange
3
(-)
Drivers kick panel.
Gray
24
D
Lock Detection
Brown
1
open
Drivers kick panel.
Gray
24
D
Trunk Release
Yellow
1
(-)
Drivers kick panel.
Red
20
D
Drivers Door
White
11
(-)
Dash fuse box.
White
12
F
Brake
Green
1
(+)
Brake pedal switch.
White
4
E
31
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Kia Optima 2008-2010
12V
Pink
5
(+)
Ignition switch.
White
6
A
Accessory
Black
3
(+)
Ignition switch.
White
6
A
Ignition
Green
6
(+)
Ignition switch.
White
6
A
Starter
Green
1
(+)
Ignition switch.
White
6
A
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Black
14
Data
OBDII.
Black
16
B
EMS COM
Yellow/Orange
21
Data
Driver kick panel, EM31.
White
33
D
Parking Lights
Pink
14
(-)
Headlight switch.
White
18
C
Lock
Pink/Black
2
(-)
Drivers kick panel.
Red
20
D
Unlock
Yellow/Black
Factory Alarm Arm
Green (key lock)
3
(-)
Drivers kick panel.
Red
20
D
12
(-)
Drivers kick panel.
Blue
20
D
Factory Alarm Disarm
Orange
17
(-)
Drivers kick panel.
Brown
20
D
Lock Detection
Brown/Orange
16
open
Drivers kick panel.
Brown
20
D
Trunk Release
White
16
(-)
Drivers kick panel.
Brown
20
D
Drivers Door
White
11
(-)
Dash fuse box.
White
12
F
Brake
Green
1
(+)
Brake pedal switch.
White
4
E
Brake
Green
1
(+)
Brake pedal switch.
White
4
E
32
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 8
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
OBDII Diagnostic
OR
15 14
C-CAN High: pin 6
8
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
2 - MC11, Yellow 24-pin connector
1 - MC41, Blue 15-pin connector
(connector side view)
).
7
13
6
12
5
DO NOT USE
Blue: pin 8
Larger 20 AWG
11
4
10 9
3
2
7
1
USE
Blue: pin 1
22 AWG
EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
C-CAN Low: pin 14
Refer to the Vehicle wiring reference chart section for
the connector, pin and wire color in your specific vehicle.
Connector
Cut
Ignition Switch
(6-pin connector)
(+) Accessory:
Blue, pin 2
(+) 12V: Red
pin 1
(+) Starter:
Green, pin 2
Immo. Data Interrupt (vehicle side): Yellow/Black: 2
Immo. Data Interrupt (connector side): Orange/Black: 3
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
FT CAN High: Orange/Green: 7
(+) Ignition:
Pink, pin 4
FT CAN Low: Orange/Brown: 8
(-) Parking Lights Output: Green/Black: 10
(+) Starter Output
(to starter): Violet
(+) Accessory Output: Orange
MC501
7 White
(+) 12V Input: Red
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
B-CAN Wires & Parking Lights
Refer to the Vehicle wiring
reference charts for the
connector, pin and wire color
in your vehicle.
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
11: Orange/Yellow:
Immobilizer Data Interrupt
(connector side)
(+) Ignition Output:
Pink
(-) Hood Input: Gray: 3
(+) 12V
10: Red: (+) 12V
9: Black: (-) Ground
Hood Pin
(+) Siren Output: Brown: 17
6: Yellow:
Immobilizer Data Interrupt
(vehicle side)
Siren
33
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Hyundai Tucson 2010-2015
12V
Red
1
(+)
Ignition switch.
White
6
A
Accessory
Blue
2
(+)
Ignition switch.
White
6
A
Ignition
Pink
4
(+)
Ignition switch.
White
6
A
Starter
Green
3
(+)
Ignition switch.
White
6
A
Parking Lights
Yellow
1
(-)
Headlight switch.
White
10
C
C-CAN High
Green
6
Data
OBDII.
Black
16
B
C-CAN Low
Orange
14
Data
OBDII.
Black
16
B
B-CAN High
Blue
8
Data
Instrument Cluster, M115-A.
White
24
G
White
24
G
Blue
15
E
B-CAN Low
Red
9
Data
Instrument Cluster, M115-A.
EMS COM
Blue
1
Data
Driver kick panel, MC41.
12V
Red
1
(+)
Ignition switch.
White
6
A
Accessory
Blue
2
(+)
Ignition switch.
White
6
A
Ignition
Green
4
(+)
Ignition switch.
White
6
A
Starter
White
3
(+)
Ignition switch.
White
6
A
Parking Lights
Blue
1
(-)
Headlight switch.
White
13
C
C-CAN High
Green
6
Data
OBDII.
Black
16
B
C-CAN Low
Orange
14
Data
OBDII.
Black
16
B
B-CAN High
Blue
20
Data
Junction Box (Right), JM01.
Black
20
D
B-CAN Low
Red
10
Data
Junction Box (Right), JM01.
Black
20
D
EMS COM
Blue
7
Data
Passenger kick panel, MC11.
Yellow
24
F
Kia Sportage 2011-2016
34
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 9
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
).
2 - Immobilizer behind fuse box
1 - Immobilizer behind fuse box
White 5-pin connector
White 8-pin connector
OR
6
EMS COM connections are only needed
if the vehicle has a transponder/immobilizer.
OBDII Diagnostic
(connector side view)
Refer to the Vehicle wiring reference charts section for
the connector, pin and wire color in your specific vehicle.
5
Connector
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
Immobilizer Data Interrupt (connector side): Yellow/Black: 2
Immobilizer Data Interrupt (vehicle side): Orange/Black: 3
C-CAN Low: pin 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) RAP Off Output: White/Violet: 11
MC501
(+) 12V Input: Red
Hood Pin
(-) Hood Input: Gray: 3
7 White
(+) Accessory Output:
Orange
8 thick-gauge wires
(+) 12V Input: Red
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
4 White
(+) Starter Output
(to starter): Violet
Starter Input
(from key switch): Green
(-) Disarm Output: Lt. Blue/Black: 13
Note:
program for
double pulse
when
flashing.
(-) Unlock Output: Dark Blue: 7
(-) Lock Output: Dark Green: 15
(+) Ignition Output:
Pink
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
Ignition Switch
(6-pin connector)
11: Orange/Yellow:
Immobilizer Data Interrupt
(vehicle side)
10: Red: (+) 12V Input
9: Black: (-) Ground
6: Yellow:
Immobilizer Data Interrupt
(connector side)
Siren
(+) Starter:
Green, pin 1
(+) Accessory:
Orange, pin 3
(+) Ignition: Blue, pin 6
(+) 12V: White, pin 5
Refer to the Vehicle
wiring reference chart.
35
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Kia Sportage (4-cyl) 2008-2010
12V
White
5
(+)
Ignition switch.
Black
6
A
Accessory
Orange
3
(+)
Ignition switch.
Black
6
A
Ignition
Blue
6
(+)
Ignition switch.
Black
6
A
Starter
Green
1
(+)
Ignition switch.
Black
6
A
EMS COM
Blue/Black
C-CAN High
Orange
14
Data
Immobilizer Module behind dash fuse box.
White
5
F
6
Data
OBDII.
Black
16
B
C-CAN Low
Parking Lights
Green
14
Data
OBDII.
Black
16
B
Brown
14
(-)
Headlight switch.
White
18
C
Lock
Green
6
(-)
Drivers kick panel.
Blue
16
D
Unlock
Blue
7
(-)
Drivers kick panel.
Blue
16
D
Factory Alarm Disarm
Pink
7
double (-)
Drivers kick panel.
Yellow
14
D
Drivers Door
Orange
8
(-)
Drivers kick panel.
Blue
16
D
Brake
Red
1
(+)
Brake pedal switch.
White
4
E
5
(+)
Ignition switch.
Black
6
A
Kia Sportage (6-cyl) 2008-2010
12V
White
Accessory
Orange
3
(+)
Ignition switch.
Black
6
A
Ignition
Blue
6
(+)
Ignition switch.
Black
6
A
Starter
Green
1
(+)
EMS COM
Brown/Orange
7
Data
Ignition switch.
Black
6
A
Immobilizer Module behind dash fuse box.
White
8
F
C-CAN High
Orange
6
Data
OBDII.
Black
16
B
C-CAN Low
Green
14
Data
OBDII.
Black
16
B
Parking Lights
Brown
14
(-)
Headlight switch.
White
18
C
Lock
Green
6
(-)
Drivers kick panel.
Blue
16
D
Unlock
Blue
7
(-)
Drivers kick panel.
Blue
16
D
Factory Alarm Disarm
Pink
7
double (-)
Drivers kick panel.
Yellow
14
D
Blue
16
D
White
4
E
Drivers Door
Pink
8
(-)
Drivers kick panel.
Brake
Red
1
(+)
Brake pedal switch.
36
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Type 10
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram (
).
EM31
(white 33-pin connector in driver’s kick panel)
EMS COM:
Yellow/Orange, pin 21
23
OBDII Diagnostic
21
(connector side view)
Cut
C-CAN High: pin 6
C-CAN wires MUST be
connected for proper
operation.
1
8
9
16
Immobilizer Data Interrupt (vehicle side):
Yellow/Black: 2
Immobilizer Data Interrupt (connector side):
Orange/Black: 3
C-CAN Low: pin 14
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 5
(-) Parking Light Output: Green/Black: 10
(-) Disarm Output: Lt. Blue/Black: 13
Note: program
for double pulse
when flashing.
Remote Start Safety
Override Switch
The Remote Start
Safety Override
Switch MUST be in
the ON position.
(+) Starter Output
(to starter): Violet
(+) 12V Input: Red
Hood Pin
(-) Hood Input: Gray: 3
(-) Unlock Output: Dark Blue: 7
MC501
(-) Trunk Release Output: Red/White: 9
(-) Lock Output: Dark Green: 15
7 White
(+) Accessory Output:
Orange
4 White
(+) 12V Input: Red
8 thick-gauge wires
Starter Input (from
key switch): Green
(+) Starter:
Black/Yellow
or White,
pin 1
(+) 12V: Black, pin 5
10: Red: (+) 12V Input
9: Black: (-) Ground
(+) Brake Input: Brown/White: 16
(+) Siren Output: Brown: 17
(+) Ignition Output:
Pink
Ignition Switch
(6-pin connector)
11: Orange/Yellow:
Immobilizer Data Interrupt
(connector side)
6: Yellow:
Immobilizer Data Interrupt
(vehicle side)
Siren
(+) Accessory:
White orOrange,
pin 3
(+) Ignition:
White/Blue or Blue,
pin 6
Refer to the Vehicle
wiring reference chart.
37
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
Locating components in the vehicle
www.directechs.com for additional information.
Wire Information
Function
Color
Connector Information
Pin
Polarity
Location
Color
Pins
Ref.
Kia Magentis 2009-2010
12V
Pink
5
(+)
Ignition switch.
White
6
A
Accessory
Black
3
(+)
Ignition switch.
White
6
A
Ignition
Green
6
(+)
Ignition switch.
White
6
A
Starter
Green
1
(+)
Ignition switch.
White
6
A
EMS COM
Yellow/Orange
21
Data
Driver kick panel, EM31.
White
33
D
C-CAN High
White
6
Data
OBDII.
Black
16
B
C-CAN Low
Black
14
Data
OBDII.
Black
16
B
Parking Lights
Yellow/Black
4
(-)
BCM At Left Of Steering Column., top conn.
White
20
C
Lock
Green
19
(-)
Drivers kick panel.
Blue
20
D
Unlock
Orange
13
double (-)
Drivers kick panel.
Brown
20
D
Trunk Release
White/Black
4
(-)
Drivers kick panel
Black
18
D
Brake
Red
9
(-)
Drivers kick panel.
Black
18
E
38
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Connecting the module
Important!
Before connecting the Directed Digital Solutions, it is important to ensure that the proper feature and function programming is
selected using the configuration wizard. Visit www.directechs.com to use the latest version of the online tool.
Flashing a module using your computer:
1. Disconnect the main module from any (+) 12V power source, then connect it to your computer using the XKLoader2.
2. Go to www.directechs.com using Internet Explorer; the configuration wizard will be displayed automatically.
3. Follow the instructions in the pop up window that will be displayed when the module is detected.
Flashing a module using your smartphone or tablet:
1. Disconnect the main module from any (+) 12V power source, then connect it to the XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on-screen instructions.
When the flashing operation is successful, you can proceed with the instructions below.
Manual or automatic transmission selection
The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop
(uncut or cut) when the main module is powered up will determine which type is selected.
• Uncut (default): Manual transmission.
• Cut: Automatic transmission.
For safety reasons, all Directed Digital Solutions are shipped ready to use with a manual transmission (the yellow loop is
untouched). If the loop is cut after power has been applied, it is necessary to cycle power to the main module (via the white 12pin main power harness) so the unit will see the state change on the loop and appropriately configure the transmission type.
Ready mode
To successfully remote start a vehicle equipped with a manual transmission, the Ready Mode feature must be enabled before
exiting the vehicle. Please refer to the Owner’s Guide for more details on this required process.
Additional connections required for vehicles equipped with a manual transmission (if not supported by firmware)
Connection
Description
(-) E-Brake Status Input
(Black/White, pin 2)
Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple
(-) trigger emergency brake circuits note some vehicles do not and may require unique integration
methodologies.
(-) Door Trigger Input
(White/Green, pin 10)
OR (+) Door Input (Yellow/
Green, pin 11)
Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor
the door pins to allow the Ready Mode process to be enabled.
Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer
to www.directechs.com.
(AC) Tachometer Input
(Violet/White, pin 6)
Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.)
and learned successfully to the Directed Digital Solutions.
Optional sensors
Note: The sensor port is only active on hybrid systems.
The
•
•
•
39
4-pin sensor port is compatible with a number of different Directed sensors including, but not limited to:
Shock Sensor – 504D
Field Disturbance Sensor – 508D
Ultrasonic Sensor – 509U
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Note: In the case of 508D, power and ground must be hardwired to the vehicle – power and ground should NOT be obtained
from the 4-pin sensor port.
Each sensor will have its own instructions, which must be followed for installation and adjustment.
RF Systems
An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist.
An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow
the instructions included with the kit for appropriate installation and programming information.
When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have
the necessary firmware to interact with the remote and Control Center (antenna) combination.
When used in conjunction with SmartStart
Disconnect power from the Directed Digital Solutions before connecting the SmartStart module. Failing to do so could damage
main module. To enable D2D communication between the Directed Digital Solutions and the SmartStart one of the following
actions must be executed:
• SmartStart with Loops – The brown loop must be cut.
• SmartStart with Pigtails – The gray wire must be connected to a ground source.
Loops
Pigtails
DO NOT connect the SmartStart 2-pin power harness when using the Directed Digital Solutions. Power and ground will be
provided by the D2D connector on main module. Refer to the SmartStart documentation for further details.
40
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Module programming
Refer to "LED diagnostics and troubleshooting" on page 45 for more information and for troubleshooting purposes.
The HKHT1 firmware has several vehicle connection options available. It is important to choose the programming method
associated with your specific installation solution in order to complete successfully the programming of your module.
Method 1 - With HS CAN & FT CAN connections & with transponder immobilizer.
*There are four Module programming possibilities, please review all methods to determine which one corresponds to your specific
vehicle.
To connect the module:
1
Please ensure that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power
harness.
3
Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
Must be connected LAST
Insert and turn the key to the ON position. The LED starts flashing green quickly.
Flashes
Quickly
Key IN
OFF
The LED starts flashing orange quickly.
(If the LED is still solid red, press Unlock on the OEM remote.)
N
&
O
4
Connect all but the
12-pin harness
START
Solid
Flashes
Quickly
The LED flashes orange slowly to indicate the bypass is being programmed.
7
Turn vehicle ignition OFF once the module is successfully programmed.
8
Pair remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
DATA Tach: Firmware using DATA Tach, the tachometer is preprogrammed for the vehicle
and no further action is required. For instructions on how to adjust the tach or use Virtual
tach, refer to page 48.
Hardwire Tach: Firmware using the Violet/White Hardwired Tach input will require
programming. For instructions on how to program or adjust the tach or use Virtual tach, refer
to page 48.
Solid
x3 Secs
Key OUT
Off
OFF
The LED turns ON solid green for 3 seconds, then shuts OFF.
N
6
9
Flashes
Slowly
Note: After 2 minutes, if the unit has not programmed, the LED will start flashing green for
another 2 minutes (maximum).
O
5
START
Pair
remotes*
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.
41
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Key IN
Method 2 - Without FT CAN & with HS CAN connections & with transponder immobilizer.
*There are four Module programming possibilities, please review all methods to determine which one corresponds to your specific
vehicle.
To connect the module:
1
Please ensure that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power
harness.
Must be connected LAST
Note: Depending on your vehicle, it may take up to 4 minutes to complete programming.
6
The LED turns ON solid orange for 3 seconds, then shuts OFF.
7
Turn vehicle ignition OFF once the module is successfully programmed.
8
Pair remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
9
DATA Tach: Firmware using DATA Tach, the tachometer is preprogrammed for the vehicle
and no further action is required. For instructions on how to adjust the tach or use Virtual
tach, refer to page 48.
Hardwire Tach: Firmware using the Violet/White Hardwired Tach input will require
programming. For instructions on how to program or adjust the tach or use Virtual tach, refer
to page 48.
START
Flashes
x1
Press &
Release x5
Flashes
Flashes
Slowly
Solid
x3 Secs
Key OUT
Off
OFF
When the LED flashes red once, press on the programming button 5 times.
The LED will then flash orange slowly.
Key IN
N
Insert and turn the key to the ON position. The LED starts flashing orange quickly.
Solid
O
4
&
OFF
Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
O
N
3
5
Connect all but the
12-pin harness
START
Pair
remotes*
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.
42
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Key IN
Method 3 - With HS CAN & FT CAN connections & without transponder immobilizer.
*There are four Module programming possibilities, please review all methods to determine which one corresponds to your specific
vehicle.
To connect the module:
1
Please ensure that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power
harness.
&
Key IN
5
When the LED flashes red 3 times, press the programming button 5 times.
Flashes
x3
6
The LED turns ON solid orange 3 seconds, then shuts OFF.
Solid
x3 Secs
7
Turn vehicle ignition OFF once the module is successfully programmed.
8
Pair remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
9
DATA Tach: Firmware using DATA Tach, the tachometer is preprogrammed for the vehicle
and no further action is required. For instructions on how to adjust the tach or use Virtual
tach, refer to page 48.
Hardwire Tach: Firmware using the Violet/White Hardwired Tach input will require
programming. For instructions on how to program or adjust the tach or use Virtual tach, refer
to page 48.
Flashes
Quickly
START
Press &
Release x5
Key OUT
START
Pair
remotes*
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.
43
Solid
x3 Secs
Off
OFF
Insert and turn the key to the ON position. The LED starts flashing green quickly.
Flashes
Quickly
N
The LED starts flashing orange quickly.
(If the LED is still solid red, press Unlock on the OEM remote.)
Solid
O
Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
OFF
4
Must be connected LAST
O
N
3
Connect all but the
12-pin harness
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Key IN
Method 4 - Without FT CAN & with HS CAN connections & without transponder immobilizer.
*There are four Module programming possibilities, please review all methods to determine which one corresponds to your specific
vehicle.
To connect the module:
1
Please ensure that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power
harness.
Must be connected LAST
4
Insert and turn the key to the ON position. The LED starts flashing orange quickly.
Key IN
Solid
Flashes
START
When the LED flashes red once, press on the programming button 5 times.
The LED will then flash orange slowly.
The LED turns ON solid orange for 3 seconds, then shuts OFF.
8
Turn vehicle ignition OFF once the module is successfully programmed.
9
Pair remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
DATA Tach: Firmware using DATA Tach, the tachometer is preprogrammed for the vehicle
and no further action is required. For instructions on how to adjust the tach or use Virtual
tach, refer to page 48.
Hardwire Tach: Firmware using the Violet/White Hardwired Tach input will require
programming. For instructions on how to program or adjust the tach or use Virtual tach, refer
to page 48..
Flashes
x3
Press &
Release x5
Solid
x3 Secs
Key OUT
Off
OFF
7
Flashes
Slowly
Press &
Release x5
N
When the LED flashes red 3 times, press on the programming button 5 times.
Flashes
x1
O
When the LED flashes red 3 times, press on the programming button 5 times.
6
10
&
OFF
Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
O
N
3
5
Connect all but the
12-pin harness
START
Pair
remotes*
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.
44
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Key IN
LED diagnostics and troubleshooting
This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.
Module programming
LED
Description
Troubleshooting
Module has no power.
Make sure the D2D harness is connected and that 12 Volt is present between the red and black
wires. If 12 Volt is present, the module may be defective.
Waiting to begin the programming
sequence.
Ensure the correct programming procedure is being followed.
Initialization failed.
Reset the module and complete the programming again. If the issue persists, please contact
Technical Support.
Transponder functions were skipped.
(If compatible) when the RXT mode is not desired or convenience features are needed, please
reset and reprogram the module.
All required CAN networks has been
detected.
Normal operation.
1 of 2 CAN networks has been detected.
Normal operation.
Key2GO initiated.
Please follow the steps indicated in "Module programming" on page 41 to complete the
Key2GO programming.
Solid green x
3 secs
Module was successfully programmed
with all functions.
Normal operation.
Solid orange x
3 secs
Module was successfully
programmed without transponder
functions.
Normal operation.
Off
Solid red
Flashes red &
green
Solid orange
Flashes green
Flashes orange
Flashes orange
slowly
Module programming – Error codes
LED
Flashes red x 1
Flashes red x 1
Flashes red x 2
Flashes red x 3
Flashes red x 4
Flashes red x 5
Flashes red x 6
Flashes red x 7
Description
Troubleshooting
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus
by turning the ignition on and try again. If your installation does not require this connection, skip
this step by pressing the programming button 5 times.
J1850 not detected.
Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try
again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not require this connection, skip this step by
pressing the programming button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire is used, make sure they are not inverted.
Ensure the vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try again. If the condition persists, please
contact Technical Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams &
vehicle wiring reference charts)" on page 8 to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams
& vehicle wiring reference charts)" on page 8 to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to
"Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the
connections.
External module synchronization
LED
Description
Troubleshooting
(Flashes red, red,
then orange) x 10
OBDII feature not supported.
The diagnostic data bus was not detected, therefore the SmartStart features will be limited.
45
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Active Ground When Running (Status)
LED
Description
Troubleshooting
Flashes green
Ground When Running (Status) command
received.
The module has initialized the remote start sequence.
Flashes red &
orange
Ignition ON command received.
The module has received the Ignition ON command and is processing the remote start sequence.
Flashes green
quickly
Start ON command received.
The module has received the Start ON command and is processing the remote start sequence.
PTS shutdown error.
The PTS output from the module was not activated due to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams & vehicle wiring
reference charts)" on page 8 to check the connections.
Description
Troubleshooting
Flashes red x 10
Flashes red x 21
Commands
LED
Flashes orange x 1
Flashes orange x 2
Flashes orange x 3
Flashes orange x 4
Flashes orange x 5
Flashes orange x 6
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
If the bypass module fails to flash, it did not receive the signal.
Commands can come from RF or D2D.
AUX2 command received.
AUX3 command received.
Shutdown codes
LED
Flashes green x 1
Flashes red x 1
Flashes red x 2
Flashes red x 3
Flashes red x 4
Description
Troubleshooting
Takeover successful.
Normal operation.
Runsafe was not disabled.
No UNLOCK command was received prior to opening the door, or the 45 second timer expired
in takeover mode.
Brake was not detected.
The brakes were not detected, which prevents the system from shutting down the vehicle.
Smart key was not detected.
The smart key was not detected, which prevents the system from shutting down the vehicle.
Speed was detected.
The vehicle was detected as moving, which prevents the system from shutting it down.
Analog error codes
LED
Description
Troubleshooting
Flashes red, green
& orange
DEI feature error.
A feature config file mismatch was detected. Please contact Technical Support.
46
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Soft reset
A module reset will only erase the steps performed in "Module programming" on page 41. The firmware and settings flashed to
the module will not be affected.
1
If required for your installation, connect all the harnesses to the Directed Digital Solutions,
EXCEPT the 12-pin main power harness. Press and hold the programming button, then
connect the 12-pin harness to the module.
2
Wait 3 seconds until the LED turns ON solid orange then release the programming button.
The LED turns ON solid red.
Connect all but the
12-pin harness
&
Solid
&
Release
Solid
Hard reset
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings may need to
be reconfigured. Connect your module to a computer and use the web configuration tool to edit its programmable features.
1
If required for your installation, connect all the harnesses to the Directed Digital Solutions,
EXCEPT the 12-pin main power harness. Press and hold the programming button, then
connect the 12-pin harness to the module.
2
After 3 seconds the LED turns ON solid orange. Keep holding the programming button until
the LED flashes red, then orange slowly.
3
Connect all but the
12-pin harness
&
Solid
&
Hold
Release the programming button. The LED turns ON solid red.
&
Release
47
Flashes
Solid
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Learning the Tach (not needed with Virtual Tach)
Tach comes preprogrammed, therefore learning is not required; however, it can be readjusted with the following operations:
1. Start the vehicle using the key.
2. Within 5 seconds, press and hold the Control Center (antenna) or the main module programming button, until the LED on the
Control Center (antenna) or the main module turns ON solid.
3. Release the button. The tachometer value is now stored in memory.
If the LED does not turn ON solid, find an alternate tach source.
Note: When the tachometer is programmed, the main module automatically enters the Tachometer engine checking mode.
Initializing Virtual Tach (not needed with hardwired or data tach applications)
To program Virtual Tach:
1. After the install is complete, remote start the engine. The programming operation may require 3 cranks of the starter before
the engine starts and runs. Do not turn off the remote start if this happens, it is a normal programming operation.
2. Once the engine begins running, let it run for at least 30 seconds.
3. Using the Remote, send the Remote start command to turn remote start off. Virtual Tach is programmed. To reset Virtual Tach, a
module reset must be done.
Note: Virtual Tach cannot be used in Manual Transmission Mode. It is also not recommended for diesel trucks.
Virtual Tach handles disengaging the starter motor during remote starting – it does not address over-rev. If the customer wants to
have the over-rev protection capability, the tach wire or data tach must be used.
Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote
start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to
compensate for such an occurrence.
48
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Limited lifetime consumer warranty
Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’s election) with a comparable reconditioned model any
Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be
defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was purchased
from an authorized Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled
in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address; the authorized dealers
name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number
and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and
accessories, carry a one-year warranty from the date of purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT
PROOF OF PURCHASE FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is non-transferable and is automatically void if: the unit’s date code
or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by
accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not
cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may
refuse the return of any unit with excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE
EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION
OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST
POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS
PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT,
DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE
UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND
GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED
DEALER’S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED
TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS,
COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A
LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY IS VOID IF
THE UNIT HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT,
UNREASONABLE USE, NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING OUT OF DEFECT IN MATERIALS
OR CONSTRUCTION.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights and you may also have other rights that vary from State to State.
This warranty is only valid for sale of product(s) within the United States of America and in Canada. Product(s) sold outside of the United States of America or
Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied.
For further details relating to warranty information of Directed products, please visit the support section of Directed’s website at: www.directed.com.
This product may be covered by a Guaranteed Protection Plan (“GPP”). See your authorized Directed dealer for details of the plan or call Directed Customer
Service at 1-800-876-0800.
(920-10011-01 2011-06)
49
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
Quick Reference Guide
Sending commands to your vehicle
Pit stop/idle mode
Whether you want to remote start the engine, lock/unlock the doors or pop the trunk,
there are 3 possible ways you can send commands to your vehicle, using the:
• Factory remote.
• Aftermarket remote.
• Directed SmartStart application via your smartphone.
Stop the vehicle in a safe parking spot and put the
gear in Park (P).
1
Press the Remote Start button on the transmitter.*
2
3
OUT
Enter the vehicle, insert your key in the Key
ignition
barrel, and turn it to the ON position.
4
Depress the brake pedal, put the car in gear and
drive off.
14:36
List of available commands
OFF
Key IN
Ready to
drive off
N
&
START
O
OFF
Enter
vehicle
N
OFF
Key IN
O
O
N
Press Unlock on
either remote*
START
Exit vehicle
with remote
* Icon and remote appearance may differ depending on the model purchased.
START
Note that the information
below is for many Viper, Clifford, Python, Avital and
14:36
Automate models. Icons and commands may differ depending on the model and
Key IN
optionsSTART
purchased. Refer to your authorized installation center for more specific
information.
OFF
Send the Unlock command on the factory or
aftermarket remote.*
14:36
Note: We recommend that you always lock the
doors of your vehicle when leaving it unattended.
N
2
Press Remote
Start button*
Parking lights flash x1
O
Close the vehicle doors, hood and trunk, then send
the Remote Start command to start the vehicle.*
Press Remote
Start button*
It is safe to leave the engine running and exit the
vehicle with the factory remote in hand.
3
1
&
The parking lights will flash once to indicate the
vehicle is now in Pit Stop Mode.
If applicable, you can also start the engine remotely by pressing the Lock button 3
times quickly on your factory remote.
Vehicle takeover with regular key
Put
gear in
Park
Button(s)
Actions
Press & hold for 1 second to lock.
* Icon and remote appearance may differ depending on the model purchased.
Press & hold for 1 second to unlock.
*
Press & hold for 1 second to remote start.
* Press & hold for 5 seconds to activate the trunk release (optional).
* Icon and remote appearance may differ depending on the model purchased.
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
SmartStart compatible
This system is compatible with Directed SmartStart. For a complete list of supported
features, please visit www.mysmartstart.com.
What is SmartStart?
Now you can remote start, lock and unlock your car just by pushing a button on your
mobile device; using the SmartStart App from Directed, the leader in vehicle security
and remote start. The simple graphical interface gives you control over the following
features of your installed remote start or security with remote start system:
• Lock/Arm
• Unlock/Disarm
• Remote Car Starter
• Trunk Release
• Panic
• AUX Channels
You can also control multiple vehicles – great for families – and assign more than
one user to control a vehicle. It’s easy with SmartStart! But, this is only the beginning!
SmartStart is loaded with additional features including GPS tracking, SmartSchedule,
vehicle status, roadside assistance, parked car finder and more.
The application enables a “Cloud-Connected Car” like never before, providing
2-way interaction with your vehicle. Connectivity is managed through the Directed
Cloud Services (DCS) network linking car, app, end user, and the Internet.
For more information, visit www.mysmartstart.com.
Notes
Directed Digital Solutions HKHT1
© 2020-03-03 Directed. All rights reserved.
">