TEK 1 User`s Manual
TEK 1 User’s Manual
TEK 1 User’s Manual
V072412
Table of Contents
Copyright & Trademark .............................................................................................................................. 4
FCC Class B Notice..................................................................................................................................... 5
Warranty ....................................................................................................................................................... 6
Introduction ................................................................................................................................................. 7
Benefits ..................................................................................................................................................... 8
Features .................................................................................................................................................... 8
Description and Installation ....................................................................................................................... 9
Description ................................................................................................................................................ 9
Rear Panel Features ............................................................................................................................... 10
Applications ............................................................................................................................................... 11
TEK 1 Applications ................................................................................................................................. 11
Standard Projector Connection............................................................................................................... 11
12 volt Security Alarm ............................................................................................................................. 12
Miniature 24 volt Security Alarm ............................................................................................................. 13
TEK 1 with Occupancy Detection and Lighting Control .......................................................................... 13
Occupancy Detection, Lighting Control and Miniature Alarm ................................................................. 15
Occupancy Detection, Lighting and Screen Control ............................................................................... 16
IR Control ................................................................................................................................................ 17
Installation ................................................................................................................................................. 18
Installing a TEK 1 .................................................................................................................................... 18
Configuring the TEK 1 ............................................................................................................................ 19
Setting a Static IP Address ...................................................................................................................... 19
Campus Network supports DHCP .......................................................................................................... 19
Campus Network does not support DHCP ............................................................................................. 19
To set a static IP address on a TEK 1 using the serial port ................................................................... 19
Determining the Current IP Address ....................................................................................................... 20
Wiring ......................................................................................................................................................... 21
Serial Port ............................................................................................................................................... 21
Device Connections ................................................................................................................................ 21
LAN Connection ...................................................................................................................................... 28
Straight-through cable ............................................................................................................................ 28
Diagnostics - Telnet .................................................................................................................................. 29
Control of a TEK 1 ..................................................................................................................................... 29
Protocol ................................................................................................................................................... 30
Server Commands .................................................................................................................................. 32
2
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
To Run a Macro ...................................................................................................................................... 32
To Send an Email ................................................................................................................................... 32
Set Schedule On/Off: .............................................................................................................................. 32
Device Commands ................................................................................................................................. 33
TEK 1 Serial Port Commands................................................................................................................. 33
Specifications ............................................................................................................................................ 34
Ethernet control interface........................................................................................................................ 34
Serial control interface ............................................................................................................................ 34
Logic Inputs............................................................................................................................................. 34
Outputs ................................................................................................................................................... 34
General ................................................................................................................................................... 34
Architectural Specifications..................................................................................................................... 35
3
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Copyright & Trademark
© Copyright 2006-2008 - TEKVOX, Inc. No part of the contents of this book may be transmitted or
reproduced in any form or by any means without the written permission of TEKVOX, Inc. All rights
reserved. This document was printed in the United States of America.
Ethernet is a trademark of XEROX Corporation. Windows XP is a trademark of Microsoft Corp.
Contacts
TEKVOX, Inc
San Antonio, TX 78232
Phone: 210.348.6565
Fax: 713.490.3135
Technical Support
Phone: 210.348.6565
Fax: 713.490.3135
Online: www.TEKVOX.com
Email: [email protected]
Sales Offices
For a current list of our sales offices, go to the TEKVOX Web site at www.TEKVOX.com
4
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
FCC Class B Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial or home environment. This equipment
generates, uses and can radiate radio frequency energy. If this equipment is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve
Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under Federal Communications Commissions rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to result in interference to radio &
television reception.
This Class B digital apparatus complies with Canadian ICES-003.
5
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Warranty
TEKVOX, Inc. warrants this product against defects in workmanship and materials for a period of Two
Years from the date of purchase. During the warranty period, if failure is caused from faulty workmanship
and/or materials, TEKVOX, Inc. will, at its option, repair or replace said products or components, to
whatever extent it shall deem necessary to restore said product to proper operating condition, provided
that it is returned within the warranty period, with proof of purchase and description of malfunction to:
TEKVOX, Inc.
2523 Facet Oak
San Antonio, TX 78232
This Limited Warranty does not apply if fault is caused by misuse, improper handling, electrical or
mechanical abuse, abnormal operating conditions or non-TEKVOX authorized modifications to said
product.
If it has been determined product is defective, please call TEKVOX and ask for an Applications Engineer
at (210) 348-6565 (USA) to receive an RMA # (Return Material Authorization Number) to begin the repair
process as quickly as possible.
Units must be returned with prepaid shipping charges. Please insure package. If not insured you assume
the risk of loss or damage during shipment. Returned units must include the serial number and a
description of the problem, as well as the contact person in case there are any questions.
TEKVOX, Inc. makes no further warranties either expressed or implied with respect to said product, or its
quality, performance, or operation for any particular use. In no event will TEKVOX, Inc. be liable for
direct, indirect, or consequential damages resulting from any defect in this product even if TEKVOX, Inc.
has been advised of such damage. Please note that laws vary from state to state and country to country,
and that some provisions of this warranty may not apply to you.
6
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Introduction
TekPatrol™ is a state-of-the-art asset management technology providing real-time supervision and
control of any device with a serial connection and released protocol. Use TekPatrol to supervise devices
and controlled areas for security and maintenance purposes. Our technology works in your classroom or
office, providing control and security of your projector, plasma, other audio visual equipment, lights and
computer equipment.
Unlike other monitoring systems that require static IP addresses, TekPatrol uses a proprietary autodiscovery method allowing each TekMonitor to be installed with its IP address set to DHCP. No longer do
you have to wait for static IP addresses from your IT group. Since our auto-discovery method does not
use the DHCP name, static IP addresses may also be used.
TekPatrol is not locked to any particular product or manufacturer to supervise or control a device such as
video projector, plasma or LCD monitor. Manufacturers like Sony, Hitachi, Panasonic, Sharp and many
other manufacturers are all accessible with TekPatrol.
Using a Client/Server device management and control tool, TekPatrol uses both hardware and software
to supervise and control a device over an IP network. Hardware is installed at the supervised device, like
a video projector. The hardware provides for Real-time supervision and control using an Ethernet-based
mini control system called a TekMonitor. The software application called TekManager gathers information
from the TekMonitors and displays it in an easy to read format on an administrator's PC. Having a minicontrol system supervise a device improves reliability and allows for easy control of other equipment, not
just projectors made by a single manufacturer.
Another benefit of the TekMonitor is its ability to supervise equipment by itself, send email notifications
and usage reports to the administrator, or send a security email if the device becomes disconnected. You
do not need to run the TekManager software for TekPatrol to do its job.
Each TekMonitor is programmed using the TekWizard software application making it easy to include room
and device driver information. All programming is provided using simple macros and a driver from our
driver library. You do not need to know any programming language to setup a TekMonitor. If you have a
product that is not listed in our driver library, please let us know and we can easily create one in most
cases.
To control a device, TekPatrol incorporates a software application called TekControl. Unlike other
monitoring and control systems that use a Web server to control a device, TekControl is an application
running from a PC located in the room with the TekMonitor and controlled device. Using a software
application provides extra security. A Web page allows easy access by anyone using a browser, once the
user name and password are broken security is lost.
7
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Benefits
•
Improves equipment life by managing operational times
•
Reduces maintenance and energy costs
•
Adds reliable security to room devices
•
Improves equipment reliability
•
Increases administrator productivity
•
Easy to configure and install
Features
•
Easy step-by-step system integration using TekWizard
•
Effortless management of devices using a view-all navigation GUI
•
Secure and easy device control from a room PC
•
Supports DHCP IP configuration using a proprietary auto-discovery method
•
Compatible with any device having a data connection and released protocol
•
Security management using a true hardware security detection method to eliminate false
Email reports
•
Monthly email usage reports
•
Lamp and Maintenance timer, Email reports
•
Event scheduling
•
Inventory and asset management
•
Supports Occupancy Sensors and lighting control
•
External control using TCP/IP to link with room controllers like AMX™ and Crestron™
8
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Description and Installation
Description
The TEK 1 is an Ethernet-based mini control system used to supervise and control video projectors,
plasma monitors, lights and many other classroom or office space devices. Unlike a control system that
requires a programmer, the TEK 1 uses an intuitive step-by-step guide called a TekWizard for
programming.
When monitoring a video projector, the TEK 1 maintains its own lamp and filter timers. The TEK 1
maintains these timers to provide uniformity in reporting and to provide timers for projectors that do not
report these timers. With a TEK 1 it is possible to monitor a device that only has IR control. For projectors
that do report these timers, the TEK 1 reports both its own and the projector’s timers. The filter timer for
the TEK 1 is called Maintenance timer. This timer can be used on any device that may require routine
maintenance like cleaning or filter changes. Both the lamp and maintenance timers are adjustable.
For theft control the TEK 1 maintains a wired connection to the monitored device and if this connection is
removed, the TEK 1 sends a Security Email. Most other monitoring systems rely on serial
communications with the device for theft control. If serial communications is lost, then the monitoring
system sends out an email. Relying on serial communications takes time and may cause false Security
Emails.
Another feature of the TEK 1 is its ability to determine a lamp error even if the projector does not report
errors. This is made possible by determining if the lamp is actually powered on when the projector is
instructed to turn on.
9
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Rear Panel Features
1. 24 volt connection: Use this power connection to power another device like an occupancy sensor
or power the TEK 1 from another power source, like a power pack for an occupancy sensor.
2. Relay 1 and 2: 2 Amp Isolated contact closer. Use these relays for devices that require isolation,
such as AC devices, or may draw larger currents.
3. DO: Digital logic Outputs 1 and 2 - 300 ma at 24 volts. These outputs must share a common
ground with the connected device. PU: 24 volt @ 8 ma (2.7K) pull-up resistor. These resistors
may be required to connect to a Digital Output to provide voltage for the connected device.
4. Logic Inputs 1-4: Use these inputs for sensing an on or off state of device like a security
connection, a room occupancy detector, a power monitor or a control button.
5. Serial connection: This connection is a programmable RS-232 data port used to pass data
between the TekMonitor and the connected device.
6. The LAN connection is an auto sensing 10/100 Ethernet connection supporting DHCP, TCP/IP,
UDP, SMTP and Telnet.
Link Led (Left)
Color
Off
Amber
Green
Meaning
No Link
10 Mbps
100 Mbps
Activity LED (Right)
Color
Off
Amber
Green
Meaning
No Activity
Half-Duplex
Fill-Duplex
The TEK 1 comes with an external 24 volt .5 amp universal power supply. Power-Over-Ethernet is not
supported. When the TEK 1 is used with an occupancy sensor and power pack, the external power
supply should not be used.
10
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Applications
TekMonitors are not programmed like other control systems using a program language; they are
configured using a PC application called TekWizard. With some IT experience an installer is able to
configure a TekMonitor by following the step-by-step guide in TekWizard. Although there is no
programming, TekWizard does provide for some logic operations in the creation of macros. A macro is
just a list of commands executed by a logic input, software, user or time event. A macro is basically a
group of commands to provide simple automation.
The Logic Inputs generate two types of events that are linked to macros. These input events occur when
the input goes high (open circuit) or low (connection to ground).
These applications provide the system integrator with some concepts of how to apply the TEK 1. Within
TekWizard are templates that coincide with these applications.
TEK 1 Applications
•
•
•
•
•
•
•
Standard Projector Connection
12 volt Security Alarm
Miniature 24 volt Security Alarm
Occupancy Detection and Lighting
Occupancy Detection, Lighting Control and Miniature Alarm
Occupancy Detection, Lighting and Screen Control
IR Control
Standard Projector Connection
TekWizard Template: TEKVOX – Standard
In a standard configuration a TEK 1 is used to control and monitor a video projector or large screen
display. The TEK 1 is installed in the ceiling and an RS-232 cable with a security wire is connected
between the TEK 1 and projector.
Features
• Internal timers for Lamp, Maintenance,
Monthly Usage, Total Usage and
System Off
• Detects cut cables for device security
(Reports by Email)
• Email Reports including Device Errors,
Monthly Usage and Security Email
11
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
12 volt Security Alarm
TekWizard Template: TEKVOX – 12V Alarm
Adding an alarm to a TEK 1 provides extra security for a video projector in a classroom. Most alarms
operate on 12 volts and draw about 500 milliamps. For these types of alarms use a separate 12 volt
power supply and one of the TEK 1 relays to operate the alarm.
Other devices like the room’s PC and monitor can also be protected by TEK 1. This is accomplished by
looping a security wire from one of the unused Logic Inputs on the TEK 1, through the PC and monitor,
and then back to ground on the TEK 1. For someone to remove any of these monitored items they must
first cut the security wire. Cutting the security wire removes the ground from the monitored input causing
an alarm event macro to be executed.
Features
•
•
•
•
Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
Detects cut cables for device security
Email Reports including Device Errors, Monthly Usage and Security Email
Enables an alarm if the security cable is cut
12
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Miniature 24 volt Security Alarm
TekWizard Template: TEKVOX – 24V Alarm
TEKVOX offers a miniature 24 volt alarm that can operate from the second Digital Output (DO 2). This
alarm operates with the same power supply powering the TEK 1.
Features
•
•
•
•
Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
Detects cut cables for device security
Email Reports including Device Errors, Monthly Usage and Security Email
Enables an alarm if the security cable is cut
TEK 1 with Occupancy Detection and Lighting Control
TekWizard Template: TEKVOX - Occupancy1
Occupancy detection for lighting has become a required device in most new installations. To improve the
performance and operation of the lighting control, the TEK 1 has the ability to interface with an occupancy
detector and lighting controls. When motion is detected, the occupancy detector triggers a high event on
Input 2 of the TEK 1. Once motion is no longer detected, the occupancy detector triggers a low event on
Input 2 of the TEK 1.
Macros
Motion –
If System Power is On - The system off countdown timer is stopped and reset.
If System On is Off - The lights go on.
13
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
No Motion –
If System Power is On - The system off countdown timer runs. If this timer reaches zero, a
system off Macro is called, shutting down the system.
If System Power is Off - The lights go off.
A 2K ¼ watt resistor is used to create an off state for the occupancy detector. When the occupancy
detector is off, its output floats causing the TEK 1 to think it is on. Placing this resistor between the input
and ground creates an off state for the occupancy detector.
From the TekControl software running on the room’s PC a message can be displayed that the system is
about ready to shut down. This allows the user to reset the system timer from the PC. Lights can also be
controlled by the user from the PC.
This method of controlling the lights from the TEK 1 solves the problem with the lights automatically
shutting off when there are only a few people in the room. Also, the TEK 1 can power off other devices
when no one is in the room, thereby saving energy and extending the bulb life of a video projector
Note that when using a Digital Output to control a lighting power pack, the logic is reversed. This means
when power is first applied to the TEK 1 the Digital Output is in an open state, causing the pull-up resistor
to supply current to turn on the power pack. Once the TEK 1 is running, a command is issued to turn on
this output causing the power pack to go off. Using a relay solves this problem.
Features
•
•
•
•
•
Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
Detects cut cables for device security
Email Reports including Device Errors, Monthly Usage and Security Email
Detects movement to automatically power on and off lights
Detects the lack of movement to automatically shut down the system
14
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Occupancy Detection, Lighting Control and Miniature Alarm
TekWizard Template: TEKVOX – Occupancy2
As mentioned above the TEK 1 has the ability to operate with an occupancy detector. Since there is an
extra logic output, a miniature alarm can be added to the TEK 1.
Features
•
•
•
•
•
•
Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
Detects cut cables for device security
Email Reports including Device Errors, Monthly Usage and Security Email
Detects movement to automatically power lights on and off
Detects the lack of movement to automatically shut down the system
Enables an alarm if the security cable is cut
15
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Occupancy Detection, Lighting and Screen Control
TekWizard Template: TEKVOX – Occupancy3
As mentioned above the TEK 1 has the ability to operate with an occupancy detector. Since there are two
relays on the TEK 1, it is possible to control a projection screen or raise and lower a projector lift.
Features
• Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
• Detects cut cables for device security
• Email Reports including Device Errors, Monthly Usage and Security Email
• Detects movement to automatically power lights on and off
• Detects the lack of movement to automatically shut down the system
• Controls other items like projection screens and projector lifts
16
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
IR Control
In some installations the display device only has IR control. For these types of installations the TEK 1 is
not able to communicate directly with the device. With a few add-on products the TEK 1 can monitor and
control these types of devices. Below are some suggested add-on type devices and how to use them with
the TEK 1.
It may not be necessary to control the projector. The projector may already be controlled by an IR device.
For these installations all that is required is to determine if the projector is on or off by using only a power
current sensor.
By adding a power current sensor at the display device the TEK 1 can determine if the device is powered
on. Once the TEK 1 knows the device is on, the internal lamp and maintenance timers within the TEK 1
are operable.
Power Current Sensor
• AMX PCS
• Display Devices PCS-02
To control the display device add a programmable RS-232 to IR. The TEK 1 can then be programmed to
communicate with the IR module.
Programmable RS-232 to IR module
• Xantech RS232IR Module
For security monitoring use the TekSecurity cable and connect the Security connection to a ground
connection on the display device.
Features
• Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and System Off
• Detects cut cables for device security (Reports by Email)
• Email Reports including Device Errors, Monthly Usage and Security Email
• Allows for IR only controlled devices
• Determines if the monitored device is actually powered on
17
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Installation
Installing the TEK 1 does not require any additional mounting hardware like projector or furniture mounts.
The TEK 1 is designed with permanent side flanges and only requires #6 wood or metal screws.
The TEK 1 should not be mounted on a monitored device and should not be easily visible. If the TEK 1 is
stolen with the device, it cannot send an Email or set an alarm. Also the power supply should not be
easily disconnected along with the projector. Although, if monitored by the TekManager software, it is
possible to send a report that the software has lost communication with the TEK 1.
Installing a TEK 1
There are two stick-on labels with the serial number and MAC address included with the TEK 1. One of
these labels can be applied to the top of the TEK 1 for easy viewing. The other can be applied to the
TekMonitor install report to reduce errors and make the install easier. Write down the model number,
serial number, asset number, if any, date of install for the monitored. Before mounting the TEK 1 make
certain that your LAN supports DHCP. If not, you will need to set a static IP address. (See Setting a Static
IP Address, page 19)
Locate a place to mount the TEK 1, usually above the ceiling. Always follow electrical codes for placing
cables and hardware in a plenum. Disconnect power from the monitored device and connect a
control/security cable between the TEK 1 and monitored device. (See Wiring Diagrams, page 21)
Connect any other devices that need to be controlled or monitored by the TEK 1. Reapply power to all
devices.
Once all TekMonitors have been installed, run TekManager and search an address range. TekManager
automatically finds each TekMonitor on the network and places them into the Holding Area. Using the
information from the install report, select TekWizard and configure an individual TekMonitor.
18
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Configuring the TEK 1
For most installations all that is required is to connect a TEK 1 to the campus network is connect a live
network cable and apply power. A DHCP server on the camps network automatically assign’s an IP
address. Unlike other monitoring type systems, you do not need to run a DOS program or connect to the
TEK 1 using a Web browser. A TEK 1 is configured by an easy to follow application called TekWizard.
Setting a Static IP Address
Before setting a static IP address, always consult with your IT administrator. You should always
keep a list of the devices that are configured using static IP address. Sometimes your IT
administrator may ask you for the MAC address of each TEK 1. To get the MAC address from a
TEK 1 you will either need to connect it to a network and run TekManager or connect to the
serial port on the TEK 1. Two labels are supplied with the TEK 1 containing both the serial
number and MAC address. See Determining the Current IP Address.
Campus Network supports DHCP
Since the network supports DHCP, just connect the TEK 1 to the network. The campus network will then
set the IP and DNS addresses. Configure a phantom TEK 1 using the TekWizard and set an assigned
static IP address or use TekManager and assign the IP address directly to the TEK 1.
Campus Network does not support DHCP
Before installing the TEK 1 you must first set the IP address. There are two ways to set a static IP
address:
1. Temporarily connect the TEK 1 to a router that supports DHCP and run TekManager.
2. Connect a computer to the serial port of the TEK 1 and initiate serial setup.
Using the router method is the easiest and allows you to configure several TEK 1s at or near the same
time. If your router is not connected to the campus network, you can set it to the same Gateway as the
campus network. Doing this allows you to configure the TEK 1s without losing communication with them
once you have changed their IP addresses.
To set a static IP address on a TEK 1 using the serial port
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Disconnect power from the TEK 1.
Connect the serial port of the computer to the serial port on the TEK 1.
Run HyperTerminal and select the Com Port and then select Configure.
Set Bits per second to (9600), Parity (None), Stop Bits (1) and Flow Control (None).
While pressing the lower case ‘x’ key apply power to the TEK 1.
Once a message is displayed, release the ‘x’ key and tap the Enter key.
Select menu item 0 - Server Configuration.
Enter the new IP address in four steps.
Select Y for Gateway and enter the new Gateway in four steps.
Enter the Subnet or Netmask.
Select menu item 9 - to save and restart with the new settings.
19
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
After the TEK 1 reboots, the following message is displayed:
*** TEKVOX TEK 1 ***
MAC address 00204A87133E
Press Enter for Setup Mode
*** basic parameters
Hardware: Ethernet TPI
IP addr - 0.0.0.0/DHCP/BOOTP/AutoIP, no gateway set
DHCP device name : TEK1-DAA0007
Change Setup:
0 Server Config:
2 Stop System for load:
7 Factory Defaults:
8 Exit W/O Save:
9 Save Exit:
Your choice ?
When setting the Subnet under the serial port configuration, a Netmask is used. A Netmask defines the
number of bits taken from the IP address that are assigned for the host part. Set the Netmask to 8 for a
255.255.255.0 Subnet.
Class A: 24 bits; Class B: 16 bits; Class C: 8 bits
Standard IP Network Netmasks
A 24
B 16
C 8
255.0.0.0
255.255.0.0
255.255.255.0
Determining the Current IP Address
1. To determine the current IP address from TekManager, select a TekMonitor and view its Network
Settings in the Properties window. Another useful method is to use the PC serial connection as
mentioned above. While pressing the lower case ‘x’ key apply power to the TEK 1.
2. Once a message is displayed, release the ‘x’ key and tap the Enter key.
3. Select menu item 8 - Exit W/O Save.
When the TEK 1 reboots it displays the following:
IP: 192.168.10.52
DHCP: TEK1-DAA0007
PC: 6373 (Current Pass Code)
20
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Wiring
The captive screw connectors on the TEK 1 support wire sizes 18-24 AWG. It is best not to tin these
wires. Tinning may cause the compression fitting of the captive screw to become loose over time.
Serial Port
Only (TX) Transmit, (RX) Receive and Ground are supported on the TEK 1. There is no hardware
handshaking. If a device requires hardware handshaking, just connect pins 7 (CTS) and 8 (RTS) together
on controlled device. Settings for the serial port are not user configurable they are only set by the
selected driver.
Most manufactures use a DB-9 type control connection and it is not always easy to determine if pin 2 or 3
is the transmit pin. An easy way to determine which is the transmit pin is to use a DC volt meter and
connect the leads between pins 5 Ground and pin 2 or 3. The pin which has between 5 and 12 volts is the
transmit pin. Connect this pin to the Receive (RX) input on the TEK 1. When both transmit and receive
connections are made correctly on the TEK 1, you should be able to register between 5 and 12 volts
between Ground and the TX pin and Ground and RX pin on the TEK 1. Of course power must be on for
both devices.
Wiring connections can be found in driver information located in TekWizard.
Device Connections
The following is a list of wire diagrams for different device manufactures including both a direct
connection or through TekSecurity.
All Connector views are from rear of the connector.
TekSecurity RJ12 Pin out
The view of the RJ12 Jack is from the front. The TekMonitor side requires a six conductor cable. The
Device side requires a four conductor cable.
WHT 1
BLK 2
RED 3
GRN 4
YEL 5
BLU 6
RJ12 Plug
RJ12 Jack
PC DB-9 FM
TEK 1 PC
GND-----5
RX-------3
TX-------2
21
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Canon LV-7245 Mini Din-8P
Direct
TEK 1 Canon
GND-----4
RX-------7
TX-------1
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Canon
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------1
RX------GRN------4------------------------4------GRN-------7
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Canon SX-50 Mini Din-8P
Direct
TEK 1 Canon
GND-----4
RX-------3
TX-------5
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Canon
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------3
RX------GRN------4------------------------4------GRN-------5
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
22
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Dell Mini Din-6P
Direct
TEK 1 Dell
GND-----1
RX-------3
TX-------5
IN1------2
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Dell
To TekMonitor To Device
Mini Din-6P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------1
TX-------RED------3------------------------3------RED-------4
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------2
PU1-----BLU-------6
Epson DB-9 FM
Direct
TEK 1 Epson
GND-----5
RX-------3
TX-------2
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Epson
To TekMonitor To Device
DB-9 FM
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------2
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Hitachi DB-15 FM
Direct
TEK 1 Hitachi
GND-----6, 7, 10
RX-------14
TX-------13
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Hitachi
To TekMonitor To Device
DB-15 FM
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------6, 7, 10
TX-------RED------3------------------------3------RED-------13
RX------GRN------4------------------------4------GRN-------14
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
23
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Hitachi DB-9 FM
Direct
TEK 1 Hitachi
GND-----5
RX-------3
TX-------2
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Hitachi
To TekMonitor To Device
DB-9 FM
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------2
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Mitsubishi Mini Din-8P
Direct
TEK 1 Mitsubishi
GND-----4
RX-------1
TX-------7
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Mitsubishi
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------1
RX------GRN------4------------------------4------GRN-------7
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
24
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
NEC DB-9 FM (LCD/Plasma)
Direct
TEK 1 NEC
GND-----5
RX-------3
TX-------2
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
NEC
To TekMonitor To Device
DB-9 FM
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------2
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
TekSecurity
NEC Mini Din-8P (Projector)
Direct
TEK 1 NEC
GND-----4
RX-------7
TX-------1
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
NEC
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------1
RX------GRN------4------------------------4------GRN-------7
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
25
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Sampo DB-9 FM
Direct
TEK 1 Sampo
GND-----5
RX-------2
TX-------3
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Hitachi
To TekMonitor To Device
DB-9 FM
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------3
RX------GRN------4------------------------4------GRN-------2
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Sanyo Mini Din-8P
Direct
TEK 1 Sanyo
GND-----4
RX-------6
TX-------1
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Sanyo
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------1
RX------GRN------4------------------------4------GRN-------6
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Sharp Mini Din-9P
Direct
TEK 1 Sharp
GND-----5
RX-------3
TX-------2
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Sharp
To TekMonitor To Device
Mini Din-9P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------2
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
26
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Sony DB-9 M
Direct
TEK 1 Sony
GND-----5
RX-------3
TX-------2
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Sony
To TekMonitor To Device
DB-9 M
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------5
TX-------RED------3------------------------3------RED-------2
RX------GRN------4------------------------4------GRN-------3
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
Toshiba Mini Din-8P
Direct
TEK 1 Toshiba
GND-----4
RX-------7
TX-------1
IN1------Shield
TekSecurity Box
TEK 1
TekSecurity
TekSecurity
Toshiba
To TekMonitor To Device
Mini Din-8P
OUT1---WHT------1
GND-----BLK------2------------------------2------BLK-------4
TX-------RED------3------------------------3------RED-------1
RX------GRN------4------------------------4------GRN-------7
IN1 -----YEL-------5------------------------5------YEL-------Shield
PU1-----BLU-------6
27
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
LAN Connection
Straight-through cable
Side 1
Side 2
Pin Wire color
Pin Wire color
1
White-orange 1
White-orange
2
Orange
2
Orange
3
White-green
3
White-green
4*
Blue
4*
Blue
5*
White-blue
5*
White-blue
6
Green
6
Green
7*
White-brown
7*
White-brown
8*
Brown
8*
Brown
* These pins are not used
28
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Diagnostics - Telnet
TEK 1 uses a standard Telnet interface on port 5074. HyperTerminal may be used to access a TEK 1 by
selecting a connection using TCP/IP and entering the IP address of the TEK 1. Once a connection is
made to the TEK 1, HyperTerminal prints out a passcode protected screen. You must know the passcode
to continue.
TEK1-LAA0024
MAC: 00:20:4A:8B:DD:35
Protocol: 1
HW Version: A
SW Version: 2.9
08:59:52 04/19/08
Please Enter Passcode: 6373
PassCode 6373
1 Print Log
2 Clear Log
3 Stop
4 Pass Thru
21 Set Time/Date
22 SMTP Port
30 Reset
Log - An error log is maintained for diagnostics.
Stop – Stops all operation of the TEK 1 for 20 seconds and then resets.
Pass Thru – Allows for sending serial ASCII commands to a device. Exiting Telnet stops Pass Thru.
1 Enter Normal Data?
2 Send LF?
3 Send STX ETX?
SMTP Port – Allows for changing the outgoing SMTP port number.
Control of a TEK 1
It is possible for a control system like AMX or Crestron to communicate with a TEK 1. This is made
possible by opening a TCP/IP connection between the control system and TEK 1 using port 5072 or the
port configured by TekManager. Since a control system cannot perform auto-discovery to locate a TEK 1,
it is necessary to configure the TEK 1 using a static IP address or at least make certain that the IP
address cannot change. There are several benefits to communicating with the TEK 1 instead of the
display device.
Both AMX and Creston modules are available from TEKVOX.
Benefits
• Cable distance is not a factor
• The display device can be changed without changing the control system software
• A standard display module can be used simplifying the control system software
When communicating with a TEK 1, it is always best to use Macros. Using Macros allows for easy
modifications to the TEK 1 driver without having to change the control system software.
29
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Protocol
Byte
0
1
2
3
Transmit
Name
Length
COMSTAT
Command
Data
Byte
0
1
2
3
Reply
Name
Length
COMSTAT
Command – If Any
Data – If Any
Once a connection is made to a TEK 1, the following start data is sent: by the TEK 1:
Data Length + COMSTAT + Start Command + Serial Number
Example:
Serial number of the TEK 1: DAA0001
$0A/$00/$00/’DAA0001’
When a Start command is received, the control system must reply with a Start Operation within 500
milliseconds.
Control System Start Operation:
Data Length + COMSTAT + Start Command + $00/$00
Example:
$05/$00/$00/$00/$00
After full communication is established, the TEK 1 sends:
• If Device Control > 255, Here Is All Device Control command plus data.
• If Device Control <= 255, Here Is Device Control End command plus data.
If the TEK 1 detects a change in its’ Device Control data, it sends a Here Is All Device Control Group
command plus new data.
Commands:
0. Start
1. Give Me All Device Control – Control System Sends to TekMonitor and TekMonitor replies with
Here Is All Device Control.
5. Here Is All Device Control - TekMonitor Sends to Control System, partial Device Control data and
Control System replies with COMSTAT.
6. Here Is All Device Control Group - TekMonitor Sends to Control System, data in the Device
Control transmit queue and TekMonitor replies with COMSTAT.
7. Here Is Device Control End - TekMonitor Sends to Control System the end or all of the Device
Control data and TekMonitor replies with COMSTAT.
9. Here Is 1 Device Control - Control System Sends command to TekMonitor and TekMonitor
replies with COMSTAT.
30
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Communications status codes (COMSTAT):
0. No error
1. Invalid data
2. Invalid command code
3. Device locked (Future)
4. Checksum error
5. Busy
6. Too Much Data
7. Data End
8. Not My Serial Number
9. Response Timeout
10. Invalid Pass Code
There are two types of commands used to communicate with a TekMonitor:
1. Server
2. Device
Both the Server and Device commands use a five byte command. Server commands allow for internal
operational functions of the TekMonitor. These commands are used to set security, run a macro or set a
schedule. Device commands control the operation of a Port. The term Port refers to input or output
device. Device commands allow for controlling a device like a projector or operating a relay.
31
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Server Commands
Command
S00(17)1
S00(18)1
S00(19)1
S00(20)1
S00(21)1
S00(30)1
S00(31)1
S00(32)1
S00(33)1
S00(40)1
S00(41)1
S00(42)1
S00(49)1
S00(59)1
S00(70)1
S00(71)1
S00(72)1
S00(79)1
S00(80)1
S00(81)1
S00(82)1
S00(89)1
Name
Enable Security
Enable Usage Report
Enable Error Messages
Enable System Off Timer
Enable Device Lockout
Schedule 1 On/Off
Schedule 2 On/Off
Schedule 3 On/Off
Schedule 4 On/Off
Macro 1
Macro 2
Macro 3
Macro 10
Macro 20
Normal Email 1
Normal Email 2
Normal Email 3
Normal Email 10
Security Email 1
Security Email 2
Security Email 3
Security Email 10
Bytes
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
Return Len /
Value (0/1 1=Enabled)
Value (0/1 1=Enabled)
Value (0/1 1=Enabled)
Value (0/1 1=Enabled)
Value (0/1 1=Enabled)
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
See Below
To Run a Macro
To run a macro, send a command followed by a 1.
To stop a macro, send a command followed by a 0.
Example:
Length/COMSTAT/Command/Data…(Server Command 5 Bytes)/Value length/Value
Run Macro 1 – 10/00/09/‘S’/00/00/40/01/01/01
Stop Macro 1 - 10/00/09/‘S’/00/00/40/01/01/00
To Send an Email
Length/COMSTAT/Command/Data…(Server Command 5 Bytes)/Value length/Value
To Send Email 1 - 10/00/09/‘S’/00/00/70/01/01/01
To Send Security Email 1 - 10/00/09/‘S’/00/00/80/01/01/01
Set Schedule On/Off:
To turn a Schedule On, send a command followed by a 1.
To turn a Schedule Off, send a command followed by a 0.
Example:
Length/COMSTAT/Command/Data…(Server Command 5 Bytes)/Value length/Value
Schedule 1 On – 10/00/09/‘S’/00/00/30/01/01/01
Schedule 1 Off - 10/00/09/‘S’/00/00/30/01/01/00
32
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Device Commands
Each device command must reference a port. The Port
value refers to the system, input or output on the TEK 1.
TEK 1 Serial Port Commands
These are the fixed location commands for
the TEK 1. A full list of these commands can
be viewed from Driver Commands under the
Report menu in TekManager.
* Standby is not a settable command, this
command is set by the TEK 1 when a
projector is in a warm up or cool down
mode.
Port
0
2
26
27
28
29
Port values
Name
Port
System
50
Com
51
Relay 1
52
Relay 2
53
DO-1
DO-2
Name
Input 1
Input 2
Input 3
Input 4
Description
Device Power
0. *Standby
1. Off
2. On
Remaining Maintenance Hrs
Monthly Usage Hrs
Total Usage Hrs
Remaining Lamp Hrs
Projector Reported Lamp Hrs
Command
‘D’ 2 ’B’ 0 1
‘D’ 2 ’O’ 0 0
‘D’ 2 ’O’ 0 1
‘D’ 2 ’O’ 0 2
‘D’ 2 ’I’ 0 1
‘D’ 2 ’I’ 1 1
‘D’ 2 ’I’ 2 1
‘D’ 2 ’I’ 3 1
‘D’ 2 ’I’ 4 1
Device Connected
‘D’ 2 ’M’ 0 0
Example:
Length/COMSTAT/Command/Data…(Driver Command 5 Bytes)/Value length/Value
Power On a Device – 08/00/09/‘D’/02/’O’/00/01
Power Off a Device – 08/00/09/‘D’/02/’O’/00/00
The following are fixed locations in the driver:
Time 000 hms 24hr
Date 0000 mdyWeekDay
Time/Date (Hrs)(Min)(Sec)
(Month)(Day)(Yr)(WeekDay)
Time/Date (Hrs)(Min)(Sec)(WeekDay)
System Off Seconds
System Power
0. Off
1. On
System Off Timer
0. Stop
1. Run
‘D’ 0 ‘T’ 0 1
‘D’ 0 ‘T’ 1 1
‘D’ 0 ‘T’ 2 0
‘D’ 0 ‘T’ 3 0
‘D’ 0 ‘I’ 1 1
‘D’ 0 ‘B’ 0 1
‘D’ 0 ‘O’ 0 0
‘D’ 0 ‘O’ 1 1
‘D’ 0 ‘B’ 1 1
‘D’ 0 ‘O’ 1 0
‘D’ 0 ‘O’ 0 1
System Power works in conjunction with the System Off Timer. This command is used to start or reset the
System Off timer, if the Enable System Off Timer is set to 1. If the System Off Macro is set to 1 and
System Power is set to Off, the System Off Macro runs.
Example:
Length/COMSTAT/Command/Data…(Driver Command 5 Bytes)/Value length/Value
Reset the System Off Timer – 08/00/09/‘D’/00/’O’/00/01
Power Off the System – 08/00/09/‘D’/02/’O’/00/00
33
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Specifications
Ethernet control interface
Connectors ........................................................... 1 - RJ-45 male connector
Data rate............................................................... 10/100Base-T, half/full duplex with auto sensing
Protocols .............................................................. DHCP, ICMP (ping), TCP/IP, UDP, Telnet, SMTP
Default settings .................................................... Link speed and duplex level are set to auto sensing.
IP address is set to DHCP.
Serial control interface
COM ..................................................................... One - RS-232 serial (TX and RX only)
Default settings
9600, 8-bit, 1 stop bit, no parity
Logic Inputs
Inputs 1 – 4 .......................................................... Four - ESD protected inputs with internal 10K pull-up
resistors, Logic High 2V, Logic Low 0.8V
Outputs
Digital (DO 1-2) .................................................... Two - open collector Darlingtons with 300 ma @ 24V
source to ground drivers
Pull-Up (PU 1-2) ................................................... Two - 2.7K 1/4 watt resistors connected to 24V (9 mA)
Relays (R1-2) ....................................................... Two - 2 Amp Isolated contact closer (Nominal 30 VDC)
General
Power ................................................................... 100-240VAC, 47/63 Hz, 0.5A, 15 watts,
DC Power ............................................................. 24 VDC 0.05 Amp
Temperature/humidity .......................................... Storage -40° to +158°F (-40° to +70°C) /10% to 90%
Non-Condensing Operation ................................. +32° to +122°F (0° to +50°C) /10% to 90%,
Enclosure type ..................................................... Metal
Enclosure dimensions
1.0" H x 6.9" W x 3.0" L
2.52 cm H x 17.50 cm W x 7.59 cm L
(Depth excludes connectors.)
Product weight ..................................................... 0.36 lbs (0.16 kg)
Shipping weight .................................................... 2 lbs (1 kg)
Listings ................................................................. UL, CUL (Power Supply Only)
Compliances ........................................................ FCC Class B, Canadian ICES-003
MTBF.................................................................... 30,000 hours
Warranty ............................................................... 2 years parts and labor
Specifications are subject to change without notice.
34
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
TEK 1 User’s Manual
V072412
Architectural Specifications
The device shall provide the following:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
One bi-directional RS-232 serial port
Four logic level inputs
Two logic outputs sourcing currents up to 300 ma @ 24V
Two - 2 Amp Isolated relays
Metal chassis with mounting flanges
24 volt DC operation
Industry standard Ethernet supporting DHCP, ICMP (ping), TCP/IP, UDP, Telnet, SMTP
Programmable E-mail errors and usage notifications
Internal Real-Time clock
Internal timers for Lamp, Maintenance, Monthly Usage, Total Usage and Time Until System Off
Programmable Macros with conditional operators
DHCP configuration with Auto-Discovery
Interface for room occupancy sensor
Project data collection into a SQL database
The device configuration shall be user programmable under the Windows® XP and Vista operating
systems. The configuration software shall provide complete setup, control and monitoring of an
apparatus.
An easy to use wizard shall provide quick setup of the device. The wizard shall provide for the ability to
load a device directly, save a configuration to a phantom device, and save a configuration to a template.
There shall be two types of configuration templates; Host and Device. The Host template shall contain
general information about a device. The Device template shall contain control information about the
monitored apparatus. Configuration templates shall be stored and recalled as required.
The configuration software shall provide for the creation of a Project from configured or phantom devices.
The contents of the Project shall be displayed in a tree like structure with the following items: Location,
Building, Group, Room and Device Name
The device shall be configured for either DHCP or Static IP addresses. The configuration software shall
provide an Auto-Discovery method which automatically locates said devices by a pass-code. Once a
device is located, the configuration software shall provide a Holding Area to display found devices by their
serial number. Devices within a Holding Area shall allow for a Drag-And-Drop method into a Project Area.
A Project shall provide a Grid View display of the devices. The Grid View shall display columns of
selected data using a format of both color and text.
The Project shall be saved and recalled as required.
Selected monitored items in the Project shall be time-stamped into a SQL database for retrieving usage,
status and asset information.
An interface for a room occupancy sensor shall be provided to automatically turn off a display device,
control lighting and provide remote status.
The device shall have certified compliance with FCC Part 15 for a Class B digital device and Canadian
ICES-003. The device shall feature an external power supply capable of operating from 100 to 240 VAC,
47-63 Hz. The external power supply shall be UL/CUL certified.
The unit shall be a TEKVOX TEK 1 TekMonitor.
35
TEKVOX, Inc. – 210.348.6565 – www.tekvox.com
San Antonio, TX 78216
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement