DATA SHEET VENTILATION ® SERVO-i UNIVERSAL HIGHLIGHTS ® For all patient categories - available in two editions NAVA - improved synchrony and unique monitoring capabilities Intuitive user interface For invasive as well as non invasive ventilation Designed for cost-efficiency The Open Lung Tool and Stress Index - tools for lung protection. Flexible placement Modular – interchangeable plug-in units Enables Heliox delivery ® Available in MR and Transport editions for continuity of ventilatory care | 2 | SERVO-i ® UNIVERSAL | Critical Care | SERVO-i VENTILATOR FAMILY ® SERVO-i UNIVERSAL UBE SERVO-i Configurations UEE Stress Index ® The SERVO-i Ventilator family consists of four configurations: ® NIV NAVA ® Infant Adult UBE UEE Universal Basic Edition Universal Extended Edition Standard Configuration Options Not applicable NAVA Heliox Nasal CPAP NIV PC NIV PS Bi-Vent Y Sensor Measuring CO2 Analyzer Nebulizer Alarm output connector ® The SERVO-i Ventilator family addresses the very different Open Lung Tool requirements of neonatal, pediatric and adult needs from a single Automode SIMV (PRVC) + PS PRVC VS SIMV (VC) + PS VC SIMV (PC) + PS PC PS/CPAP All patient category software ventilation platform. All four configurations are the same ventilator, equipped with different functions. They can be customized and upgraded with different options for future needs. (SERVO-i Adult and SERVO-i Infant can also be upgraded to SERVO-i Universal.) The same ventilator can be used at the bedside, during transport* and in the MR-room* facilitating training, operation and maintenance, increasing efficiency and flexibility. SERVO-i Universal is an intensive care ventilator for all patient ® categories and is available in two editions - Basic and Extended, the latter featuring a wide range of modes and functions as standard. *An agreement with MAQUET must be signed, see conditions in the SERVO-i MR declaration (Order no. 66 71 670) and the Interhospital Transport Declaration (Order no. 66 64 721) respectively. KEY TO ABBREVIATIONS NAVA NIV SIMV PRVC VS VC PS PC CPAP Neurally Adjusted Ventilatory Assist Non-invasive ventilation Synchronized Intermittent Mandatory Ventilation Pressure Regulated Volume Control Volume Support Volume Control Pressure Support Pressure Control Continuous Positive Airway Pressure | Critical Care | SERVO-i ® UNIVERSAL | 3 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL The system - General Non-operating conditions The device complies with requirements of Medical Device Directive 93/42/EEC. Impact: Peak acceleration: 15 g. Pulse duration: 6 ms. Number of impacts: 1000. Classification: Class I equipment. According to IEC/EN 60 601-1. Storage temperature: –25 to +60º C (–13 to 140º F) Storage Relative Humidity: < 95% Standards: IEC/EN 60 601-1 (Type B). IEC/EN 60 601-2-12. EN 794-1. Storage Atmospheric Pressure: 470 to 1060 hPa Noise level: <50 dBA, measured at 0.3 m distance. Power supply IP classification IP 20 Electromagnetic compatibility (EMC): Emission: According to IEC/EN 60601-1-2 (Edition 2:2001). Immunity- Extended test to 30 v/m: According to IEC/EN 60601-1-2. The 'EMC Declaration, Information to the Responsible Organization' is available from MAQUET. Patient range: Weight: Power supply, automatic range 100 – 120 V AC ±10%, 50 – selection: 60 Hz, or 220 – 240 V AC ±10%, 50 – 60 Hz. Plug-in battery module: Battery backup: Two battery modules are delivered with the ventilator. Up to six battery modules can be included. Battery capacity: Rechargable, 12 V, 3.5 Ah each. Recharge time: Approximately 3 h/battery. Battery backup time: At least 3 h, when using six batteries. Adult, all ventilation modes: 10 - 250 kg Infant, invasive ventilation: 0.5 - 30 kg External 12 V DC: 12.0 V – 15.0 V DC, 10 A Infant, NAVA + NIV NAVA: 0.5 - 30 kg Max power consumption: Infant, NIV PS+PC: 3 - 30 kg Infant, Nasal CPAP: 0.5 - 10 kg At 100 – 120 V: 2 A, 190 VA, 140 W. At 220 – 240 V: 1 A, 190 VA, 140 W. Operating conditions Operating temperature: +10 to +40ºC Relative humidity: 15 to 95% non-condensing Atmospheric pressure: 660 to 1060 hPa Lowest pressure in breathing system: –400 cmH2O | 4 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL The ventilator - General Dimensions: User interface (See dimensional drawings page 15) User Interface: W 355 x D 53 x H 295 mm Patient Unit: W 300 x D 205 x H 415 mm Weight: Approximately 5 kg Attachment: Can be attached to the mobile cart, a table, rail or pole (15 – 30 mm diameter). Weight: Approximately 20 kg (Patient Unit 15 kg, User Interface 5 kg) Method of triggering: Flow, pressure and Edi (optional) Type: TFT-LCD module Size: 31 cm (12.1”) diagonal Approximately 115 cmH2O Viewing area: 246.0 x 184.5 mm Max. operating pressure: Screen Bias flow: Adult: 2 l/min Infant: 0.5 l/min Gas supply Inlet gas pressure Air/O2: Pressure drop: Max. 6 cmH2O at a flow of 1 l/s Internal compressible factor: Max. 0.1 ml/cmH2O Gas delivery system: Microprocessor controlled valve Inspiratory flow range: 200 – 650 kPa / 2.0 – 6.5 bar / 29 – 94 PSI Connection standards available: AGA, DISS, NIST, or French standard. Unavailable gas/loss of gas pressure: Inspiratory channel The flow from an unavailable gas (air or O2) is automatically compensated for so that the patient gets the preset volume and pressure. Adult: 0 to 3.3 l/s Infant: 0 to 0.55 l/s Expiratory channel Pressure drop: Max. 3 cmH2O at a flow of 1 l/s Internal compressible factor: Max. 0.1 ml/cmH2O PEEP regulation: Microprocessor controlled valve Patient system gas connectors Rise time, expiratory flow measurement: <12 ms for 10 – 90 % response at flow of 0.05 – 3.2 l/s Conical fittings: Male 22 mm / female 15 mm. In accordance with ISO 5356-1. Expiratory flow range: 0 to 3.2 l/s Gas exhaust port: Male 30 mm cone | Critical Care | SERVO-i ® UNIVERSAL | 5 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Alarms Alarms Airway pressure (upper): Battery: Adult, invasive ventilation: 16 - 120 cmH2O Adult, Non Invasive Ventilation: 16 - 40 cmH2O Infant, Invasive ventilation: 16 - 90 cmH2O Infant, Non Invasive Ventilation 16 - 40 cmH2O Expired minute volume (Upper alarm limit): Adult: 0.5 – 60 l/min Infant: 0.01 – 30 l/min Expired minute volume (Lower alarm limit): Adult: 0.5 – 40 l/min Infant: 0.01 – 20 l/min Limited battery capacity: 10 min. No battery capacity: less than 3 min. Low battery voltage. End-tidal CO2 (upper and lower 0.5 – 20%. 4 – 100 mm Hg. limit): 0.5 – 14 kPa. Leakage out of range in NIV: Yes. Described in the User’s manual. Technical: Yes. Described in the User’s manual. Autoset (alarm limits) specification: Invasive ventilation, controlled modes only. High airway pressure: Mean peak pressure +10 cmH2O or at least 35 cmH2O. Upper minute volume: It is possible to permanently silence this alarm (an option with Infant version only) Expiratory minute volume + 50%. Lower minute volume: Expiratory minute volume – 50%. No patient effort (Apnea) alarm Upper respiratory frequency: Breathing frequency + 40%. Adult: 15 – 45 s Lower respiratory frequency: Breathing frequency – 40%. Infant 2 – 45 s Automatic return to support mode on patient triggering High end expiratory pressure: Mean end expiratory pressure + 5 cmH2O. No consistent patient effort: Yes, described in User's manual Low end expiratory pressure: Mean end expiratory pressure – 3 cmH2O. Respiratory frequency: 1 – 160 breaths/min High end expiratory pressure: 0 – 55 cmH2O Low end expiratory pressure: 0 – 47 cmH2O. Note. Setting the alarm to 0 (zero) is equal to alarm off. High continuous pressure: Set PEEP level + 15 cmH2O exceeded for more than 15 seconds. O2 concentration: Set value ±5 vol% or 18 vol% Gas supply: Below 200 kPa / 2.0 bar / 29 PSI and above 650 kPa / 6.5 bar / 94 PSI Upper end tidal carbon End tidal carbon dioxide dioxide concentration (etCO2): concentration + 25%. Lower end tidal carbon End tidal carbon dioxide dioxide concentration (etCO2): concentration – 25%. | 6 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Ventilation Modes – Invasive ventilation Ventilation modes – Non-invasive Ventilation (optional) Controlled ventilation: NIV PC PC VC PRVC NIV PS Can be configured with alternative flow patterns - VC with flow adaptation, - VC without flow adaptation, - VC with decelerating flow Optional with Universal Basic Edition Nasal CPAP Ventilation modes - NAVA (optional) NAVA Assist via endotracheal tube or tracheostomy Supported ventilation: NIV NAVA PS/CPAP VS SIMV (VC) + PS: Comes with the corresponding controlled ventilation mode SIMV (PC) + PS: Comes with the corresponding controlled ventilation mode SIMV (PRVC) + PS Comes with the corresponding controlled ventilation mode (optional with Universal Basic Edition) Automode Pressure controlled ventilation on two independently adjustable levels, allowing unrestricted spontaneous breathing on both levels. (Optional) Control mode: VC <—> Support mode: VS Control mode: PC <—> Support mode: PS Control mode: PRVC <—> Support mode: VS Optional with Universal Basic Edition Neurally Adjusted Ventilatory Assist via non-invasive patient Optional with Universal Basic Edition Combined ventilation: Bi-Vent Neurally Adjusted Ventilatory interfaces Waveform and loop presentations Real time waveforms - up to 4 waveforms can be displayed simultaneously: Pressure Flow Volume CO2 Requires SERVO-i CO2 Analyzer option Edi Requires SERVO-i NAVA option Loops: Volume / Pressure* *A reference loop and three overlaying loops can be displayed. Flow / Volume* *Displayed simultaneously with Open Lung Tool graphical trends, if requested. | Critical Care | SERVO-i ® UNIVERSAL | 7 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Displayed value Yes Trended value* Yes Monitoring End Expiratory Flow: Displayed value Yes Trended value* Yes Spontaneous breaths per minute (RRsp): No Yes Static Compliance: Yes Yes Dynamic Compliance: Yes Yes Peak Airway Pressure: Yes Yes Stress Index Yes Yes Mean Airway Pressure: Yes Yes Inspiratory Resistance Yes Yes Pause Airway Pressure: Yes Yes Expiratory Resistance Yes Yes End Expiratory Pressure: Yes Yes Elastance Yes Yes CPAP Pressure: Yes Yes Time Constant Yes No Inspired Tidal Volume: Yes Yes P0.1: Yes Yes Expired Tidal Volume: Yes Yes Work of Breathing patient: Yes Yes Inspired Minute Volume: Yes Yes Work of Breathing ventilator Yes Yes Expired Minute Volume: Yes Yes Shallow Breathing Index (SBI) Yes Yes Leakage fraction in NIV (%): Yes Yes Supply pressure (O2 and air): Yes No Ti/Ttot: Yes No Battery remaining time: Yes No I:E ratio: Yes No Barometric pressure: Yes No Total PEEP: Yes No Edi peak: Yes Yes Edi min: Yes Yes O2 Concentration (measured): Yes Yes CO2 End tidal concentration (etCO2): Yes Yes CO2 Minute elimination (CO2): Yes Yes Tidal CO2 elimination (VTCO2): Yes Yes Monitoring Breathing frequency: MVe sp / MVe: Yes No Spontaneous Exp. Minute Volume (MVe sp): Yes Yes *Stored trend values for up to 24 hours Log function Event log: Alarms. Ventilator settings. Apnea periods. Immediate functions. Service log: Technical alarms. Test results. Preventive maintenance. Service history. Configuration log. | 8 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Parameter settings Setting range: Parameter settings Setting range: Parameter: Infant Adult Parameter: Infant Adult Inspiratory tidal volume (ml): Inspiratory minute volume (l/min): 2 – 350 100 – 4000 O2 concentration (%): 21 – 100 21 – 100 0.3 – 20 0.5 – 60 I:E ratio: 1:10 – 4:1 1:10 – 4:1 TInsp (s): 0.1 – 5 Apnea, time to alarm (s): 5 – 45 0.1 – 5 15 – 45 Automode Trigger timeout (s): 3 – 15 NAVA level (cmH2O/µV): 0 - 15 0 - 15 7 – 12 Edi trigger sensitivity (µV): 0.1 – 2.0 PC/PS above PEEP (cmH2O) 0 – (80 -PEEP) 0 – (120 -PEEP) 0.1 – 2.0 TPause (s): PC/PS above PEEP in NIV (cmH2O) 0 – (32 - PEEP) 0 – (32 - PEEP) PEEP (cmH2O) 0 – 50 0 – 50 PEEP in NIV (cmH2O) 2 – 20 2 – 20 CPAP pressure (cmH2O): 2 – 20 CMV frequency (breaths/min): 0 – 1.5 0 – 1.5 TPause (% of breath cycle time): 0 – 30 0 – 30 Flow trigger sensitivity level (fraction of bias flow): 0 – 100% 0 – 100% Press. trigg sensitivity (cmH2O): -20 – 0 -20 – 0 – Insp. rise time (% of breath cycle time): 0 – 20 0 – 20 4 – 150 4 – 150 Insp. rise time (s): 0 – 0.2 0 – 0.4 SIMV frequency (breaths/min): 1 – 60 1 – 60 Insp. cycle off (% of peak flow): 1 – 70 1 – 70 Breath cycle time, SIMV (s): 0.5 – 15 1 – 15 (PEEP + 1) – 50 (PEEP + 1) – 50 Insp. cycle off in NIV (% of peak 10 – 70 flow): 10 – 70 PHigh (cmH2O) THigh (s): 0.2 – 10 0.2 – 10 Nebulizer time (min): 5 – 30 5 – 30 TPEEP (s): 0.2 – 10 0.2 – 10 PS above PHigh (cmH2O): 0 – (80 - PHigh) 0 – (120 PHigh) Backup settings Setting range: Parameter: Infant Adult Inspiratory tidal volume (ml): 2 – 350 100 – 4000 PC above PEEP (cmH2O) 5 – (80 -PEEP) 5 – (120 -PEEP) PC above PEEP in NIV 5 – (32 -PEEP) 5 – (32 -PEEP) CMV frequency (breaths/min): 4 – 150 4 – 150 I:E ratio: 1:10 – 4:1 1:10 – 4:1 TInsp (s): 0.1 – 5 0.1 – 5 | Critical Care | SERVO-i ® UNIVERSAL | 9 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Parameter: Setting range Communication/Interface Oxygen breaths: 100% for 1 minute Start breath: Initiation of 1 breath (In SIMV mode initiation of 1 mandatory breath) Screen picture transfer (optional) Pause hold: Insp. or exp (0 – 30 seconds) Alarm silence/reset: 2 minute silence and reset of latched alarms Compliance compensation: On/Off Adult 65 l/min Automode (optional with Universal Basic Edition): Automode On/Off Infant, NIV: 25 l/min Infant, Nasal CPAP: 15 l/min Nebulizer (optional) 5 - 30 min./Continuous/Off Backup ventilation Backup On/Off Suction Support Pre oxygenation time: Max. 2 min Post oxygenation time: Max. 1 min Suction phase time: No maximum level Adjustable oxygen level: 21 – 100 % Saving of data Recording of current waveform 20 seconds of data will be and parameter values: recorded (10 seconds before and 10 seconds after activation). Communication/Interface Serial port: RS-232C - isolated. For data communication via the Communication Interface Emulator (CIE). Second serial port (optional) See information above. Alarm output connector (optional) Connector: 4-pole Modular connector Ratings: Max 40 V DC, Max 500 mA, Max 20 W Network connection (optional): MIB (Medical Information Bus) monitor connection Data transfer (optional): Via Ventilation Record Card Via Ventilation Record Card Non-invasive Ventilation (optional) Max. leakage compensation level Leakage overrange detection: Automatic Disconnect detection: Automatic Disconnect flow: Configurable Low 7.5 l/min High - 40 l/min (Adult) - 15 l/min (Infant) Disabled Deactivates disconnect detection Connect detection: Manual, or automatic via bias flow | 10 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Open Lung Tool (OLT) (optional with Universal Basic Edition) Three simultaneous graphical trends, presented breath-by-breath: 1. 2. 3. EIP and PEEP (End Inspiratory Pressure and Positive End Expiratory pressure). VTi and VTe (Inspiratory and Expiratory Tidal volume). Stress Index (optional) Presented values: PEEP (Positive End Expiratory pressure). VTe (Expiratory Tidal volume). Stored values: C dyn i and VTCO2* (Dynamic inspiratory Compliance [= VTi/(EIP – PEEP)] and Tidal CO2 elimination*). Cursor function: Zoom function: Time marking: A cursor can be moved with the main rotary dial or via the touch screen. When moving it along the graph, the numeric parameter values valid for that actual moment will be shown. Time resolution of the x-axis can be selected in five different steps. Hours and minutes (when values are measured). 120 values stored in graph Stored trend values up to 24 hours Cursor function: A cursor can be moved with the main rotary dial. When moving it along the graph, the numeric parameter values valid for that actual moment will be shown. Time marking: Hours and minutes (when values are measured). * Requires SERVO-i CO2 Analyzer option. Values stored breath by breath: Up to 21.600 breaths. SI (Stress Index) NAVA (optional) Standards: IEC/EN 60601-1 (Type CF, defibrillator proof) Size: Edi module: 154 x 90 x 21 mm Edi catheter cable: Length: 2 m Weight - Edi module: 0.25 kg Power source - Edi module supply voltage: Powered from SERVO-i. <3 W at 12 V (normal operation) Parameters: Edi waveform Edi leads waveforms NAVA estimated pressure waveform (Pest) Edi catheters: 6 Fr, length 49 cm 6 Fr, length 50 cm 8 Fr, length 100 cm 8 Fr, length 125 cm 12 Fr, length 125 cm 16 Fr, length 125 cm | Critical Care | SERVO-i ® UNIVERSAL | 11 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL SERVO-i CO2 Analyzer (optional) SERVO-i CO2 Analyzer – Performance Standard: Measuring method: Mainstream, dual-wavelength, non-dispersive infrared. Parameters: Capnogram. CO2 End tidal concentration (etCO2). EN 864, ISO 9918. IEC/EN 60601-1 (Type BF, defibrillator proof) Size: CO2 Analyzer Module: 154 x 90 x 43 mm Sensor: 32.0 x 42.4 x 21.6 mm CO2 Minute elimination ( CO2). Tidal CO2 elimination (VTCO2). Measuring range: 0 to 100 mm Hg CO2 partial pressure. 0 to 13.3 kPa CO2 partial pressure. 0 to 13.2% CO2 volume (at a barometric pressure of 1013 hPa). Step response time: <25 ms (10 to 90% step response). Warm-up time: 30 s to initial CO2 indication, max. 5 min to full specification. Oxygen concentration compensation: Automatic. Values supplied from the SERVO-i Ventilator System. CO2 Analyzer Module supply Powered from the SERVO-i. voltage: Barometric pressure compensation: Automatic. Values supplied from the SERVO-i Ventilator System. Power consumption: Digitizing rate: 87 Hz Weight: CO2 Analyzer Module: 0.45 kg Sensor: 18 g Airway adapter: 10 g Connectors and cables: CO2 Analyzer Module: 15-pole D-sub female connector. Sensor: 20-pole, 2.4 m cable. Power source: Sensor: 8 W at 12 V, during warm up. 6.5 W at 12 V, during normal operation. Powered from the CO2 Analyzer Module. Airway adapter dead space: Adult: <5 ml Infant: <0.5 ml | 12 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Y Sensor measuring (optional) Servo Ultra Nebulizer (optional) Size: Y Sensor Module: 154 x 90 x 43 mm Y sensor adult: Length 84 mm Y sensor infant: Length 51 mm Weight: Y Sensor Module: 0.4 kg Y sensor adult: 10.5 g Y sensor infant: 7.5 g Weight: Approx. 125 g Dimensions: H 105 mm x L 108 mm x W 60 mm Connection cable length: 2.0 m Nebulizer T-piece connections: Inlet/outlet: 22/15 mm outer/inner diameter and 22 mm inner diameter, ISO standard. Pediatric patient tubes: Adapters 22/10 mm outer diameter and 15/10 mm outer diameter. Sensor material: Makrolon polycarbonate. Internal volume: Tubing: 2.0 m. Medical grade PVC. Ultrasonic generator frequency: 2.4 MHz Power source – Y Sensor Module supply voltage: Powered from the SERVO-i. <5 W at 12 V (normal operation). Particle size (water): Y Sensor measuring – Performance Measuring method: Fixed orifice, differential pressure. Parameters: Airway pressure. Airway flow. Inspiratory and expiratory volumes. Infant: Mass Median Diameter (MMD) = approximately 4.0 µm, measured distally in endotracheal tube 8 mm inner diameter. Output from nebulizer (water) – Min. 0.1 ml water/min at 0.1 l minimum water flux: gas flow/s. Min. 0.3 ml water/min at 0.5 l gas flow/s. Min. 0.5 ml water/min at 1.0 l gas flow/s (Adult only). Buffer liquid: Sterile water 2 to 180 l/min Max. medication temperature: 55º C (131º F) 0.125 to 40 l/min Volume, medication cup: Max. 10 ml Noise level: Max. 50 dBA, measured at 0.3 m distance. Measuring range: Adult: 60 ml Airway adapter dead space: Adult: < 9.0 ml Infant: < 0.45 ml | Critical Care | SERVO-i ® UNIVERSAL | 13 | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Aeroneb Nebulizer Systems (optional) SERVO-i Holder (optional) Weight - Aeroneb module: Weight: 3.5 kg Dimensions: H 352 mm x L 247 mm x W 159 mm (see dimensional drawing below) Approx. 216 g Dimensions - Aeroneb module: H 105 mm x L 108 mm x W 60 mm Connection cable length: 2.0 m Particle size (water): 1 - 5 mass median aerodynamic diameter (MMAD) Flow rate: >2 ml/min Volume - nebulizer unit Residual volume: SERVO-i Shelf Base (optional) Pro - 10 ml Weight: 1.2 kg Solo - 6 ml Dimensions: H 29 mm x L 205 mm x W 159 mm (see dimensional drawing below) 10 % SERVO-i Mobile Cart (optional) Gas cylinder restrainer (optional) Weight: 20 kg Max load: Dimensions: H 1015 mm x L 640 mm x W 560 mm (see dimensional drawing below) SERVO-i Drawer kit (optional) Weight: 4.5 kg Dimensions: H 240 mm x L 210 mm x W 300 mm 2 x 5-liter bottles SERVO-i IV Pole (optional) Max load (total): 6 kg Gas trolley (optional) Max load: 2x10 kg bottles Docking: Dockable to SERVO-i Mobile Cart. Dockable to a separate wall clamp. | 14 | SERVO-i ® UNIVERSAL | Critical Care | TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Compressor Mini (optional) Note See separate data sheet. For inaccuracies and more detailed technical specifications please refer to the User’s manual. Service Regular maintenance: Once every 12 months or at least after 5000 operating hours. ORDERING INFORMATION SERVO-i, Ventilator and accessories: See separate information: “SERVO-i, Version 6.1 — System Flow Chart” (Order no: 66 70 102). | Critical Care | SERVO-i TECHNICAL SPECIFICATIONS ® SERVO-i UNIVERSAL Dimensional drawings SERVO-i on Mobile Cart SERVO-i (patient unit) on SERVO-i Holder SERVO-i Shelf Base SERVO-i Holder ® UNIVERSAL | 15 | © Maquet Critical Care AB 2011. All rights reserved. • MAQUET reserves the right to modify the design and specifications contained herein without prior notice. Order No. 66 70 105 • Printed in Sweden • 111116 • Rev: 12 English • Data Sheet Maquet Critical Care AB Röntgenvägen 2 SE-171 54 Solna, Sweden Phone: +46 (0) 8 730 73 00 www.maquet.com For local contact: Please visit our website www.maquet.com GETINGE GROUP is a leading global provider of products and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences. We operate under the three brands of ArjoHuntleigh, GETINGE and MAQUET. ArjoHuntleigh focuses on patient mobility and wound management solutions. GETINGE provides solutions for infection control within healthcare and contamination prevention within life sciences. MAQUET specializes in solutions, therapies and products for surgical interventions, interventional cardiology and intensive care.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project