User manual M2

User manual M2
User manual M2
Direct voltage signals: Shunt 0-60-150-300-1000 mV
Technical features:
• red display from -19999…99999 digits (optional: green, orange or blue display)
• minimal installation depth: 70 mm without plug-in terminal
• adjustment via factory default or directly on the sensor signal
• Min-/Max memory
• 30 parameter driven setpoints
• display flashing at threshold exceedance or undershooting
• zero-key for triggering of HOLD, TARA
• permanent min-/max-value recording
• volume measurement (totaliser)
• mathematical functions like reciprocal value, square root, square and rounding
• programming interlock via access code
• protection class IP65 at the front
• plug-in terminal
• two relay outputs optional
• optional analog output or sensor supply
• optional galv. insulated digital input
• accessories: pc-based configuration-kit PM-TOOL with CD & USB adapter
for devices without keypad, for a simple adjustment of standard devices
M2_12GB.pdf Stand: 04.11.2011
96x48
Identification
STANDARD-TYPES
ORDER NUMBER
Direct voltage: Shunt
Housing size: 96x48 mm
M2-1VR5B.0002.570BD
M2-1VR5B.0002.670BD
Options – breakdown of order code:
M 2- 1 V R 5 B. 0 0 0 2. 6 7 2 B D
Basic type M-Line
Dimension
D physical unit
Installation depth
incl.plug-in terminal 89 mm
2
Version
B B
Housing size
96x48x70 mm (BxHxD)
1
Setpoints
0 no setpoints
Display type
V, A
V
2 2 relay outputs
Protection class
1 without keypad,
Display colour
Blue
B
Green
G
Red
R
Orange
Y
Number of digits
5 digits
operation at the back
7 IP65 / plug-in terminal
Supply voltage
4 115 VAC
5 230 VAC
5
6 10-30 VDC galv. insulated
14 mm
B
Measuring input
2 Shunt 0-60-150-300-1000 mV
Digital input
none
one
0
I
Analogoutput
0 without
X 0-10 VDC, 0/4-20 mA
Digit height
Sensor supply
0 without
Please state physical unit by order, e.g. m/min.
Contents
1.
Assembly
2
2.
Electrical connection
3
3.
Function and operation description
4
4.
Setting up the device
6
4.1. Switching on
6
4.2. Standard parameterisation (flat operation level)
6
4.3. Extended parameterisation (professional operation level)
10
4.3.1. Signal input parameters „INP“
10
4.3.2. General device parameters „FCT“
14
4.3.3. Safety parameters „COD“
17
4.3.4. Analog output parameters „Out“
19
4.3.5. Relay functions „rel“
21
4.3.6. Alarm parameters „AL1…AL4“
24
4.3.7. Totaliser (Volume measurement) „tot“
26
4.3.8. Programming lock „run“
27
4.4. Reset to default values
27
4.5. Alarms / Relays
28
4.6. Sensor calibration offset / final value
29
5.
Technical data
30
6.
Safety advice
32
7.
Error elimination
33
1
1. Assembly
1. Assembly
Please read the Safety advice on page 32 before installation and keep this user manual
for future reference.
3,0
48,0
M2
Se
alin
g
,0
89
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand.
Then use a screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
2
2. Electrical connection
2. Electrical connection
3
3. Function and operation description
3. Function and operation description
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to
set the device into operation are displayed. To get into the professional level, run through
the menu level and parameterise “prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser
function etc. In this level function groups which allow an extended parameterisation of the
standard settings are availabe. To leave the menu group level, run through this level and
parameterise „uloc„ under menu item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be
changed or adjusted, are always signalised by a flashing of the display. Settings that are
made in the parameterisation level are confirmed with [P] and thus safed. By pressing the
[O]-key it leads to a break-off of the value input and to a change into the menu level. All
adjustments are safed automatically by the device and changes into operating mode, if no
further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu level
Keys for up and down navigation in the menu level.
Change into operation mode.
To confirm the changes made at the parameterization level.
Parameterisation
level
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu group level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
4
3. Function and operation description
Programming via the configuration software PM-TOOL MUSB4:
This configuration kit includes the software on CD, a USB-cable and a device adapter. It is
connected via a 6-pole micromatch-plug on the back side of the device. The connection to
the PC via an USB-plug.
System requirements: PC with USB-interface
Software:
Windows XP, Windows VISTA
Function chart:
5
4. Setting up the device
4. Setting up the device
4.1. Switching-on
Once the installation is complete, you can start the device by applying the voltage supply.
Before, check once again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed,
followed by an indication of the software type and, after that, also for 1 second, the software
version. After the starting sequence, the device switches to operation/display mode.
4.2. Standard parameterisation: (flat operation level)
To parameterize the display, press the [P] key in operating mode for 1 second. The display
then changes to the menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: su.060
There are several measuring input options: 60, 150, 600 or 1000 mV signals as works
calibration (without application of the sensor signal) and SU as sensor calibration (with
the sensor applied). Confirm the selection with [P] and the display switches back to
menu level.
Setting the measuring range end value, End:
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. A minus sign can only be parameterized on the highest value digit. After
the last digit, the display switches back to the menu level. If Sens was selected as input
option, you can only select between noca and cal. With noca, only the previously set
display value is taken over, and with cal, the device takes over both the display value
and the analogue input value.
6
4. Setting up the device
Menu level
Parameterisation level
Setting up the measuring range start/offset value, OFFS:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and
confirm each digit with [P]. After the last digit the display switches back to the menu
level. If Sens was selected as input option, you can only select between noca and cal.
With noca, only the previously set display value is taken over, and with cal, the device
takes over both the display value and the analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P].
The display then switches back to the menu level again.
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 sec up
to 1 sec and in increments of 1.0 sec up to 10.0 sec. Confirm the selection by pressing
the [P] button. The display then switches back to the menu level again.
Selection of analog output, Out.rA:
Default: 4-20
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this
function, the demanded signal is selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. A minus sign can only be parameterised on the
highest digit. After the last digit, the device changes back into menu level.
7
4. Setting up the device
Menu level
Parameterisation level
Setting up the initial value of the analog output, Out.OF:
Default: 0
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. A minus sign can only be parametrised on the highest
digit. After the last digit, the device changes back into menu level.
Threshold values / limit values, LI-1:
Default: 2000
For both limit values, two different values can be parameterized. With this, the
parameters for each limit value are called up one after another.
Hysteresis for limit values, HY-1:
Default: 0
For all limit values exists a hysteresis function, that reacts according to the settings
(threshold exceedance / threshold undercut).
Function if display falls below / exceeds limit value, FU-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit
value exceedance can be selected with high (HIGH = upper limit value). If e.g. limit
value 1 is on a switching threshold of 100 and occupied with function „high“, the alarm
will be activated by reaching the threshold. If the limit value is allocated to „Low“, an
alarm will be activated by undercut of the threshold.
Threshold values / limit values, LI-2:
Default: 3000
For both limit values, two different values can be parameterized. With this, the
parameters for each limit value are called up one after another.
8
4. Setting up the device
Menu level
Parameterisation level
Hysteresis for limit values, HY-2:
Default: 0
For all limit values exists a hysteresis function, that reacts according to the settings
(threshold exceedance / threshold undercut).
Function if display falls below / exceeds limit value, FU-2:
Default: high
A limit value undercut is selected with Louu (for LOW = lower limit value), a limit value
exceedance with High (for HIGH = higher limit value). If e.g. limit value 1 is on a
threshold level of 100 and allocated with function High, an alarm is activated by
reaching of the threshold level. By allocation of limit value Louu , an alarm is activated
by falling below the threshold value.
User code (4-digit number-combination, free available), U.CodE:
Default: 0000
If this code is set, the user can only choose from a reduced number of parameter sets.
He has e.g. no access to the scale of the measuring inputs. Still, a changing of the
limit values and the allocation of the analog output are allowed. This reduced
parameterisation is activated by selecting LOC in menu item run. The device confirms
the setting with „- - - - -„ and changes into operation mode. By pressing [P] for 3
seconds in operation mode, the display shows COde and thus confirms the change into
the reduced parameterisation. It stays activated as long as the standard
parameterisation is activated again by the input of A.Code (master code).
Master code (4-digit number-combination free available), A.CodE:
Default: 1234
No parameterisation is allowed if this code is set. This function ist activated by
selecting LOC in menu item run. The device confirms the setting with „- - - - -„ and
changes into operation mode. By pressing [P] for 3 seconds in operation mode, the
display shows COde and thus confirms the activation of the master code. The user can
only come to the parameterisation by the correct input of the number-combination. It
stays activated as long as ULOC is entered in menu group run, this sets the device
back into standard parameterisation.
9
4. Setting up the device
Menu level
Parameterisation level
Activation / deactivation of the programming lock or completion of the standard
parameterization with change into menu group level (complete function range),
run:
Default: uloc
With the navigation keys [▲] [▼], you can choose between the deactivated key lock
Uloc (works setting) and the activated key lock Loc, or the menu group level ProF.
Confirm the selection with [P]. After this, the display confirms the settings with
"- - - - -", and automatically switches to operating mode. If Loc was selected, the
keyboard is locked. To get back into the menu level, press [P] for 3 seconds in
operating mode. Now enter the CODE (works setting 1 2 3 4) that appears using [▲] [▼]
plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
To parametrise further functions ProF needs to be set. The device confirms this setting
with „- - - - - „ and changes automatically in operation mode. By pressing [P] for
approx. 3 seconds in operation mode, the first menu group InP is shown in the display
and thus confirms the change into the extended parameterisation. It stays activated as
long as ULOC is entered in menu group RUN , thus the display is set back in standard
parameterisation again.
4.3. Extended parameterisation (professional operation level)
4.3.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: su.060
There are several measuring input options: 60, 150, 600 or 1000 mV signals as works
calibration (without application of the sensor signal) and SU as sensor calibration (with
the sensor applied). Confirm the selection with [P] and the display switches back to
menu level.
10
4. Setting up the device
Menu level
Parameterisation level
Setting up the measuring range end value´, End:
Default: 10000
The final value has to be adjusted from the smallest to the highest digit with [▲] [▼]
and needs to be confirmed digit per digit with [P]. A minus sign can only be
parametrised on the highest digit. After the last digit, it can then be chosen between
nOCA and CAL. With nOCA the display value that has been adjusted bevor can now be
taken over, with CAL the matching is done via the measuring section and the analog
input value is taken over. It is always adopted to 100%. With [P] the selection is
confirmed and the device changes back into menu level.
Setting up the measuring range start/offset value, OFFS:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and
confirm each digit with [P]. After the last digit the display switches back to the menu
level. If Sens was selected as input option, you can only select between noca and cal.
With noca, only the previously set display value is taken over, and with cal, the device
takes over both the display value and the analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P].
The display then switches back to the menu level again.
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1
second and in increments of 1.0 up to 10.0 seconds. Confirm the selection by
pressing the [P] button. The display then switches back to the menu level again.
11
4. Setting up the device
Menu level
Parameterisation level
Rescaling the measuring input values, EndA:
Default: 10000
With this function, you can rescale the input value of e.g. 19.5 mA (works setting)
without applying a measuring signal. If sensor calibration has been selected, these
parameters are not available.
Rescaling the measuring input values, OFFA:
Default: 0
With this function, you can rescale the input value of e.g. 3.5 mA (works setting)
without applying a measuring signal. If sensor calibration has been selected, these
parameters are not available.
Setting up the tare/offset value, tArA:
Default: 0
The given value is added to the linearized value. In this way, the characteristic line
can be shifted by the selected amount.
Setting of the balance point, Adj.pt:
Default: 08000
The balance point is preset on 80%. This means, during the semi-automatic sensor
calibration a checking of the range is done for the offset and the final value. If the
setting range was exceeded or undercut by +/-20 % then the failure report C.fail is
displayed.
Setting up the physical unit, UnIt:
Default: no
One can choose between the above shown physical units. It will be displayed on the
5th digit of the display.
12
4. Setting up the device
Menu level
Parameterisation level
Number of additional setpoints, SPCt:
Default: 00
8 additional setpoints can be defined to the initial- and final value, so linear sensor
values are not linearised. Only activated setpoint parameters are displayed.
Display values for setpoints, dIS.01 … dIS.30:
Under this parameter setpoints are defined according to their value. At the sensor
calibration, like at Endwert/Offset, one is asked at the end if a calibration shall be
activated.
Analog values for setpoints, InP.01 … InP.30:
These setpoints are displayed at works setting (4-20 mA) only. Here, demanded
analog values can be choosen freely. The input of steadily rising analog values needs
to be done self-contained.
Device undercut, dI.Und:
Default: -i9999
With this function the device undercut (_ _ _ _ _) can be defined on a definite value.
Display overflow, dI.OUE:
Default: 99999
_____
With this function the display overflow (
) can be defined on a definite value.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „–INP-“.
13
4. Setting up the device
4.3.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display time, DISEC:
Default: 01.0
then
The display is set up with [▲] [▼]. Thereby you jump until 1 second in 0.1 steps and
until 10.0 seconds in 1.0-steps. With [P] the selection is confirmed and the device
changes into menu level.
Rounding of display values, round:
Default: 00001
This function is for instable display values, where the display value is changed in
1-, 5-, 10- or 50-steps. This does not affect the resolution of the optional outputs. With
[P] the selection is confirmed and the device changes into menu level.
Arithmetic, ArItH:
Default: no
Root extraction
Reciprocal
Square
With this function the calculated value, not the measuring value, is shown in the
display. With no , no calulation is deposited. With [P] the selection is confirmed and
the device changes into menu level.
Sliding average determination, AVG:
Default: 10
Here, the number of the meterings that need to be averaged is preset. The time of
averaging results of the product of measuring time SEC and the averaged metering AVG.
With the selection of AVG in the menu level DISPL, the result will be shown in the display
and evaluated via the alarms.
14
4. Setting up the device
Menu level
Parameterisation level
Zero point slowdown, ZErO:
Default: 00
At the zero point slowdown, a value range around the zero point can be preset, so the
display shows a zero. If e.g. a 10 is set, the display would show a zero in the value
range from -10 to +10; below continue with -11 and beyond with +11.
Display, dISPL:
Default: actua
With this function the current measuring value, Min-/Max value, totaliser value, the
process-controlled Hold-value or the sliding average value can be allocated to the
display. With [P] the selection is confirmed and the device changes into menu level.
Display flashing, FLASH:
Default: no
A display flashing can be added as additional alarm function either to single or to a
combination of off-limit condition. With no, no flashing is allocated.
Assignment (deposit) of key functions, tASt:
Default: no
For the operation mode, special functions can be deposited on the navigation keys
[▲] [▼], in particular this function is made for devices in housing size 48x24 which do
not have a 4th ( [O] key). If the MIN-/MAX-memory is activated with EHtr, all measured
MIN/MAX-values are safed during operation and can be recalled via the navigation
keys.
15
4. Setting up the device
Menu level
Assignment
(deposit)
of key
functions,
tASt:
Parameterisation level
The values get lost by re-start of the device. If the threshold value correction LI.12 or
LI.34 is choosen, the values of the threshold can be changed during operation without
disturbing the operating procedure. With tArA the device is tared to zero and safed
permanently as offset. The device acknowledges the correct taring with oo0oo in the
display. Set.tA adds a defined value on to the currently displayed value. Via totAL the
current value of the totaliser can be displayed for approx. 7 seconds, after this the
device jumps back on the parametrised display value. If tot.rE is deposited, the
totaliser can be set back by pressing of the navigation keys [▲] [▼], the device
acknowledges this with ooooo in the display. By allocation on EHt.rE the MIN/MAXmemory is deleted. At ActuA the measuring value is shown for approx. 7 seconds, after
this the device jumps back on the parametrised display value. If no is selected, the
navigation keys are without any function in the operation mode.
Special function [O]-key, tASt.4:
Default: no
…
For the operation mode, special functions can be deposited on the [O]-key. This
function is activated by pressing the key. With tArA the device is tared to zero and
safed permanently as offset. The device acknowledges the correct taring with oo0oo in
the display. Set.tA adds a defined value on to the currently displayed value. Via totAL
the current value of the totaliser can be displayed for approx. 7 seconds, after this the
device switches back on the parametrised display value. If tot.rE is deposited, the
totaliser can be set back by pressing of the navigation keys [▲] [▼], the device
acknowledges this with ooooo in the display. EHt.rE deletes the MIN/MAX-memory. If
HOLD has been selected, the moment can be hold constant by pressing the [O]-key,
and is updated by releasing the key. Advice: Hold is activated only, if HOLD is selected
under parameter DISPL. ActuA shows the measuring value for approx. 7 seconds, after
this the device jumps back on the parametrised display value. The same goes for AVG,
here the sliding average value is displayed. Via se.cal a sensor calibration is done by
pushing the [O]-key, the sequence programm is shown in chapter 4.5. At AL-1…AL-4
there can be set an output and therewith e.g. a setpoint adjustment can be done. If no
is selected, the [O]-key is without any function in the operation mode.
16
4. Setting up the device
Menu level
Parameterisation level
Special function digital input, dIG.In:
Default: no
…
In operation mode, the above shown parameters can be laid on the optional digital
input, too. Function description see tASt.4.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– fct –“.
4.3.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
User code, U.Code:
Default: 0000
Via this code reduced sets of parameters can be set free. A change of the U.CodE can
be done via the correct input of the A.CodE (master code).
Master code, A.Code:
Default: 1234
By entering A.CodE the device will be unlocked and all parameters are released.
17
4. Setting up the device
Menu level
Parameterisation level
Release/lock analog output parameters, Out.LE:
Default: all
Analog output parameters can be locked or released for the user:
- At En-oF the initial or final value can be changed in operation mode.
- At Out.EO the output signal can be changed from e.g. 0-20mA to 4-20mA or 0-10VDC.
- At ALL analog output parameters are released.
- At no all analog outpout parameters are locked.
Release/lock alarm parameters, AL.LEU:
Default: all
This parameter describes the user relase/user lock of the alarm.
- LIMIt, here only the range of value of the threshold values 1-4 can be changed.
- ALrM.L, here the range of value and the alarm trigger can be changed.
- ALL, all alarm parameters are released.
- no, all alarm parameters are locked.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– cod –“.
18
4. Setting up the device
4.3.4. Analog output parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference analog output, OutPt:
Default: actua
The analog output signal can refer to different functions, in detail this are the current
measuring value, Min-value, Max-value, totaliser-/sum-function or the sliding average
value. If HoLd is selected the signal of the analog output will be hold and processed
just after deactivation of HOLD. With [P] the selection is confirmed and the device
changes into menu level.
Selection analog output, Out.rA:
Default: 4-20
There are 3 output signals availabe: 0-10 VDC, 0-20 mA and 4-20 mA. With this
function the demanded signal can be selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value can be adjusted from the smallest to the highest digit with [▲] [▼].
Confirm each digit with [P]. A minus sign can only be parameterized on the highest
value digit. After the last digit, the display switches back to the menu level.
19
4. Setting up the device
Menu level
Parameterisation level
Setting up the initial value of the analog output, Out.OF:
Default: 00000
The initial value can be adjusted from the smallest to the highest digit with [▲] [▼].
Confirm each digit with [P]. A minus sign can only be parameterized on the highest
value digit. After the last digit, the display switches back to the menu level.
Overflow behavior, O.FLoU:
Default: edge
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behaviour
of the analog output can be defined. As overflow can be seen either EdGE, that means
the analog output runs on the set limits e.g. 4 and 20 mA, or to.OFF (input value smaller
than initial value, analog output switches on e.g. 4 mA), to.End (higher than final value,
analog output switches to e.g. 20 mA). If to.MIn or to.MAX is set, the analog output
switches to the smallest or highest possible binary value. This means that values of
e.g. 0 mA, 0 VDC or values higher than 20 mA or 10 VDC can be reached. With [P]
the selection is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– out –“.
20
4. Setting up the device
4.3.5. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alarm relay 1, rEL-1:
Default: al-1
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be
inserted at activated alarms AL1/4 or de-activated alarms ALN1/4. If LOGIC is selected,
logical links are available in the menu level LoG-1 and CoM-1. One can only get to these
two menu levels via LOGIC, at all other selected functions, these two parameters are
overleaped. Via On/OFF the setpoints can be activated/de-activated, in this case the
output and the setpoint display are set/not set on the front of the device. The
parameters Cal, Cal.of and Cal.en are only used in combination with the semi-automatic
calibration (chapter 4.5 sensor calibration). At cal, the relay switches during sensor
calibration, at cal.of during the offset calibration and at cal.en during the final value
calibration. With [P] the selection is confirmed and the device changes into menu
level.
21
4. Setting up the device
Menu level
Parameterisation level
Logic relay 1, Log-1
Default: or
Here, the switching behaviour of the relay is defined via a logic link, the following
schema describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
As soon as a selected alarm is activated, the
relay operates. Equates to operating current
principle.
____ _ _
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms
are active.
____ _ _
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 1, CoM-1:
Default: or
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a
group of alarms can be chosen. With [P] the selection is confirmed and the device
changes into menu level.
Alerting relay 2, reL-2:
Default: al-2
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be
inserted at activated alarms AL1/4 or de-activated alarms ALN1/4. If LOGIC is selected,
logical links are available in the menu level LoG-1 and CoM-1. One can only get to these
two menu levels via LOGIC, at all other selected functions, these two parameters are
overleaped. Via On/OFF the setpoints can be activated/de-activated, in this case the
output and the setpoint display are set/not set on the front of the device. The
parameters Cal, Cal.of and Cal.en are only used in combination with the semi-automatic
calibration (see chapter 4.5). At cal, the relay switches during sensor calibration, at
cal.of during the offset calibration and at cal.en during the final value calibration. With
[P] the selection is confirmed and the device changes into menu level.
22
4. Setting up the device
Menu level
Parameterisation level
Logic relay 2, LoG-2:
Default: or
Here, the switching behaviour of the relay is defined via a logic link, the following
schema describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
____ _ _
As soon as a selected alarm is activated, the
relay operates. Equates to operating current
principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms
are active.
____ _ _
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 2, CoM-2:
Default: a. 2
….
The allocation of the alarms to relay 2 happens via this parameter, one alarm or a
group of alarms can be chosen. With [P] the selection is confirmed and the device
changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– rel –“.
23
4. Setting up the device
4.3.6. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Dependency alarm1, ALrM.1:
Default: actua
The dependency of alarm 1 can be related to special functions, in detail these are the
current measuring value, the MIN-value, the MAX-value, the totaliser-/sum-value or
the sliding average value. Is Hold selected, then the alarm is hold and processed just
after deactivation of HOLD. EHtEr causes the dependency either by pressing the [O]-key
on the front of the housing or by an external signal via the digital input. With [P] the
selection is confirmed and the device changes into menu level.
Threshold values / limit values, LI-1:
Default: 2000
For both limit values, two different values can be parameterized. With this, the
parameters for each limit value are called up one after another.
Hysteresis for limit values, HY-1:
Default: 00000
For all limit values exists a hysteresis function, that reacts according to the settings
(threshold exceedance / threshold undercut).
24
4. Setting up the device
Menu level
Parameterisation level
Function if display falls below / exceeds limit value, FU-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit
value exceedance can be selected with high (HIGH = upper limit value). If e.g. limit
value 1 is on a switching threshold of 100 and occupied with function „high“, the alarm
will be activated by reaching the threshold. If the limit value is allocated to „Low“, an
alarm will be activated by undercut of the threshold.
Switching-on delay, ton-1:
Default: 000
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
Switching-off delay, toF-1:
Default: 000
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– Ali –“.
The same applies to –Al2– to –Al4–.
25
4. Setting up the device
4.3.7. Totaliser (volume measurement)
Menu group level
Menu level
Menu level
Parameterisation level
Totaliser state, total:
Default: off
The totaliser makes measurements on a time base of e.g. l/h possible, at this the
scaled input signal is integrated by a time and steadily (select Stead) or temporarily
(select temp) safed. If Off is selected, the function is de-activated. With [P] the
selection is confirmed and the device changes into menu level.
Time base, t.base:
Default: sec
Under this parameter the time base of the measurement can be preset in seconds,
minutes or hours.
Totaliser factor, Facto:
Default: 10Π0
…
At this the factor (100…106) respectively the divisor for the internal calculation of the
measuring value is assigned.
Setting up the decimal point for the totaliser, tot.dt:
Default: 0
The decimal point of the device can be adjusted with the navigation keys [▲] [▼].
With [P] the selection is confirmed and the device changes into menu level.
26
4. Setting up the device
Menu level
Parameterisation level
Totaliser reset, tot.re:
Default: 00000
The reset value is adjusted from the smallest to the highest digit with the navigation
keys [▲] [▼] and digit per digit confirmed with [P]. After the last digit, the display
switches back to the menu level. The activator for the reset is parameter driven via the
4th key or via the optional digital input.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– tot –“.
4.3.8. Programming lock, run:
Menu group level
Description see page 11, menu level run
4.4. Reset to default values
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent
operation. This puts the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
27
4. Setting up the device
4.5. Alarms / Relays
This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or
exceedance. Each alarm can be allocated to an optional relay output S1-S2; furthermore
alarms can be controlled by events like e.g. Hold or Min-/Max-value.
Function principle of alarms / relays
Alarm / Relay x
De-activated, instantaneous value, Min-/Max-value, Hold-value,
totaliser value
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating strom / Quiescent current
Operating current
By operating current the alarm S1-S2 is
off below the threshold and on on
reaching the threshold.
Quiescent current
By quiescent current the alarm S1-S2 is
on below the threshold and switched off
on reaching the threshold.
Switching-on delay
The switching-on delay is activated via
an alarm and e.g. switched 10 seonds
after reaching the switching threshold, a
short-term exceedance of the switching
value does not cause an alarm,
respectively does not cause a switching
operation of the relay. The switching-off
delay operates in the same way, keeps
the alarm / the relay switched longer for
the parametrised time.
28
4. Setting up the device
4.6. Sensor calibration offset / final value
The device has an semi-automatic sensor calibration, where a switching output operates an
80% adjustable resistors, as one finds in some sensors. Like this, offset and final value are
adjusted, and the sensor can be applied directly after this. The calibration can be done via
the 4th key or the digital input, depending on the parameterisation.
Push Trigger for minimum 3
seconds.
For min. 1 measuring cycle,
min. 1s or max. by trigger.
Current measuring range
value in per cent.
For min. 1 measuring cycle, min. 1s
or max. by trigger.
Breached at +/- 20% range
monitoring.
switching output
activated., e.g. 80%
For min. 1 measuring cycle,
min. 1s or max. by trigger.
Current measuring range value
in per cent.
For min. 1 measuring cycle,
min. 1s or max. by trigger.
Breached at +/20% range
monitoring.
Switch-off 80%-switching ouput
and display for min. 1 measuring
cycle or min. 1s waiting time.
Back to regular operation mode.
Back to regular operation mode
after 1s or 1 measuring cycles.
If a special input range Su.060, Su.100, Su.300 or su.150 was selected under type, a checking of
the range is done for offset and final value. At an undercut/exceedance of +/- 20% of
adjustment range, an C.FAIl is given out.
29
5. Technical data
5. Technical data
Housing
Dimensions
96x48x70 mm (BxHxD)
96x48x89 mm (BxHxD) incl. plug-in terminal
Panel cut-out
92.0+0.8 x 45.0+0.6 mm
Wall thickness
up to 15 mm
Fixing
Screw elements
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
Standard IP65 (Front), IP00 (back side)
Weight
approx. 200 g
Connection
plug-in terminal; wire cross section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
Red (optional green, yellow or blue)
Range of display
-19999 to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the bottom
Display time
0.1 to 10.0 seconds
Input
Measuring
range
Ri
Measuring fault
Digit
-5…75 mV
0…60 mV
~12 kΩ
0.2 % of measuring range
±1
-15…180 mV
0…150 mV
~60 kΩ
0.2 % of measuring range
±1
-30…360 mV
0…300 mV
~30 kΩ
0.2 % of measuring range
±1
-100…1200 mV
0…1000 mV
~200 kΩ
0.2 % of measuring range
±1
Digital input
< 24 V OFF, 10 V ON, max. 30 VDC
RI ~ 5 kΩ
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-conversion
Resolution
approx. 18 Bit at 1 second measuring time
30
5. Technical data
Output
Analogausgang
0/4-20 mA or 0-10 VDC 16 Bit reversible
Switching output
Relay
Switching cycles
with change-over contacts 250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive load
10 x 106 mechanically
Diversity according to DIN EN50178
/ Characteristics according to DIN EN60255
Power supply
230 VAC +/- 10 % max. 10 VA
10-30 VDC galv. insulated, max. 4 VA
Memory
EEPROM
Data life
≥ 100 years
Ambient conditions
Working temperature
0…50°C
Storing temperature
-20…80°C
Climatic density
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity to directive 2004/108/EG
Safety standard
According to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
31
6. Safety advices
6. Safety advices
Please read the following safety advice and the assembly chapter 1 before installation
and keep it for future reference.
Proper use
The M2-device is designed for the evaluation and display of sensor signals.
Danger! Careless use or improper operation can result in
personal injury and/or damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should
there be any visible damage, we recommend close examination of the packaging. Please
inform the supplier immediately of any damage.
Installation
The M2-device must be installed by a suitably qualified specialist (e.g. with a
qualification in industrial electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to
transformers, mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and
suppress any interference with the aid of RC spark extinguishing combinations or freewheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them
parallel with each other. Position “go” and “return lines” next to one another. Where
possible use twisted pair. So, you receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect
the screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life
and/or can destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs
to be avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic insulated potentials within one complex need to be placed on a appropriate point
(normally earth or machines ground). So, a lower disturbance sensibility against impacted
energy can be reached and dangerous potentials, that can occur on long lines or due to
faulty wiring, can be avoided.
32
7. Error elimination
7. Error elimination
Error description
Measures
1.
The unit permanently indicates
overflow.
• The input has a very high measurement, check
the measuring circuit.
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
2.
The unit permanently shows
underflow.
• The input has a very low measurement, check the
measuring circuit .
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values
and re-configure the unit according to your
application.
4.
Program numbers for parameterising
of the input are not accessible.
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment
display
• Please contact the manufacturer if errors of this
kind occur.
6.
The device does not react as
expected.
• If you are not sure if the device has been
parameterised before, then follow the steps as
written in chapter 5.2. and set it back to its
delivery status.
33
M2_12GB.pdf
Stand: 04.11.2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement