User`s manual
User’s manual
IKBT12 Bluetooth Stereo
Music Audio Receiver
„
1.
2.
3.
Before use…………………………………………………………………………………1
About IKBT12…………………….…………………………….……………………….1
System requirements…………………………………….…………………………1
Overview of IKBT12…………..…………………………….………………………...1
„
1.
2.
3.
4.
5.
Getting started………………………………………………..………………………2
Charging the receiver…………………………………………………………………....2
Turning on/off the receiver………………………………………….…………………...2
Pairing with Bluetooth devices……………………………..……..………………….…3
Music playback……………………………………………..……………………….5
LED indicator………………………….……………………..…………………………...5
„ Care and maintenance………………….………………………..………………………6
„ FAQs………………………………….………………………………..………………….6
„ Specifications………………………………………………………………………...7
Welcome to use this Bluetooth stereo receiver IKROSS IKBT12. Please read this user’s
manual carefully before use.
„ Before use
1. About IKBT12
IKBT12 is a stereo Bluetooth receiver. You can use an common audio device with 3.5mm
audio in jack for playing back any stereo Bluetooth-enabled device’s music after plugging in
IKBT12.
The product comes with a built-in rechargeable battery, it can be usded for about 12 hours
after being charged fully.
2. System requirements
‹ Audio device with 3.5mm audio in jack, such as speakers, radios etc .
‹ Bluetooth transmitting device supporting A2DP profile, such as Bluetooth mobile phones,
Bluetooth MP3s etc.
3. Overview of IKBT12
1
2
3
4
MFB button — Power on/off, pair, music pause/play
Charging jack — DC 5V
LED indicator — Indicate current status
3.5mm audio in plug — Connect to audio device
1
„ Getting started
1. Charging the receiver
IKBT12 comes with a built-in rechargeable battery, prior to using it, it is recommended to
charge the battery fully for the first time.
When the receiver is low power, red LED flashes once and the receiver emits three tones
every 20 seconds. Please recharge the battery of the receiver.
Connect the charger to a standard power outlet and the charger plug to the charging jack of
the receiver. Red LED is on while charging. It takes about 2.5 hours to charge the battery
fully. When charging has completed, red LED will be off.
Remarks:
1) If the receiver can’t be turned off, you can charge it to turn it off.
2) Please don’t attempt to take out the battery from the speaker, as this might damage it.
Warning:
1) The battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place,
such as sunshine, fire or the like.
2. Turning on/off the receiver
Function
Power on
Power off
Operation
LED indicator
Press and hold MFB button for 3~5 seconds
Press and hold MFB button for 3~5 seconds
2
Blue LED is on for 1 second
Red LED is on for 1 second
3. Pairing with Bluetooth devices
How to enter pairing mode
Function
Operation
Enter pairing mode
Ensure the receiver is turned off,
otherwise turn it off first and
then press and hold MFB button
for 6~7 seconds until LED
flashes red and blue alternately
LED
indicator
LED
flashes red
and blue
alternately
Indication tone
Two “DU” tones
Remark: The pairing mode will last 2 minutes, the receiver IKBT12 will switch to standby
mode automatically if no devices can be connected within 2 minutes.
Pairing with Bluetooth mobile phone
Ensure your mobile phone supports A2DP profile. The pairing procedures will vary
depending on different models of mobile phones. Please refer to your mobile phone user’s
manual for further information. The general pairing procedures are as follows:
1) Place the receiver and Bluetooth mobile phone where they are easily viewable by no
more than 1 meter apart;
2) Enter the receiver’s pairing mode (please refer to “How to enter pairing mode);
3) Activate your mobile phone’s Bluetooth function and set your mobile phone to search for
Bluetooth devices within range, and select “ikross” from the list of devices shown;
4) According to the indication, enter password or PIN No: “0000”;
5) If prompted by your mobile phone to connect, select “Yes” (This will vary among mobile
phone models);
6) After successful connecting, blue LED flashes twice quickly every 5 seconds
Remarks:
If no devices can be connected within 5 minutes, the receiver will then turn off
automatically in order to save power.
‹ After successful pairing, the receiver and the mobile phone will remember each other,
they will no need to re-pair next time.
‹
3
‹
‹
‹
‹
Every time the receiver is turned on, it will automatically connect to last connected
device. If you want to pair it with other devices, please turn off the Bluetooth function of
last connected devices first and pair the receiver with the new device according to steps
1~6 mentioned above.
When the reveiver is turned on and doesn’t connect to any devices, press MFB button
twice, it will automatically connect to the last connected device.
When the receiver and the mobile phone are out of effective range to disconnected, they
can connect to each other automatically once going back to effective range.
If the Bluetooth version of your mobile phone is V2.1 or above, it will no need to enter
PIN No. when the receiver pairs with the mobile phone.
Pairing with Bluetooth transmitter
You can connect the receiver with a Bluetooth transmitter to enjoy music wirelessly. Hereby
take BTT010 (Bluetooth transmitter for iPod, not included) for example. The pairing
procedures are as follows:
1) Place the receiver and the Bluetooth transmitter where they are easily viewable by no
more than 1 meter apart;
2) Enter the receiver’s pairing mode (Please refer to “How to enter pairing mode);
3) Turn on the Bluetooth transmitter. It will automatically search for Bluetooth devices and
send a pairing request;
4) When the receiver requests to enter a PIN No., the transmitter will response “0000”
automatically;
5) After successful pairing and connecting, blue LED of the receiver will flash twice
quickly every 5 seconds.
Remarks:
‹ The pairing password of the receiver is “0000”. So, the receiver can only pair with a
Bluetooth transmitter whose pairing password is “0000”.
‹ If pairing still fails after several tries, please refer to the Bluetooth transmitter’s user’s
manual for further information.
4
4. Music playback
Connect IKBT12 to an speaker and a Bluetooth music device at the same time, now you can
enjoy music wirelessly.
Function
Pause
Status of IKBT12
Playing music
Operation
Short press MFB button once
Play
Pausing
Short press MFB button once
Remarks:
‹ The music will automatically pause when you dial a phone number or there is an
incoming call.
‹ IKBT12 hasn’t a microphone, so you need to switch the call to the mobile phone. The
music will automatically play when the call is ended.
5. LED indicator
LED indicator
LED flashes red and blue alternately
Pairing mode
Status of IKBT12
Blue LED flashes once every 2 seconds
Standby mode and not connected
Blue LED flashes twice every 5 seconds
Connected
Red LED flashes once every 20 seconds
Low power
5
„ Care and maintenance
Read the following recommendations before using the receiver. Following these you will be
able to enjoy the product for many years.
‹ Do not expose the receiver to liquid, moisture or humidity to avoid the product’s internal
circuit being affected.
‹ Don’t use abrasive cleaning solvents to clean the receiver.
‹ Do not expose the receiver to extremely high or low temperature as this will shorten the
life of electronic devices, destroy the battery or distort certain plastic parts.
‹ Don’t dispose of the receiver in a fire as it will result in an explosion.
‹ Don’t bring the receiver into contact with sharp objects as this will cause scratches and
damages.
‹ Don’t let the receiver fall down onto the floor. The internal circuit might get damaged.
‹ Don’t attempt to disassemble the receiver as it may get damaged if you are not
professional.
‹ If you do not plan to use the receiver for a long time, please store it in a dry place that is
free from extreme temperatures and dust.
In case the receiver doesn’t function properly, send it to the store you bought it. The staff
will help you to solve the problem.
„ FAQs
1. What to do when IKBT12 can’t be turned on?
Please charge the IKBT12.
2. What to do when BTR001 can’t pair and connect to a Bluetooth device?
a) Make sure the Bluetooth device is placed within 5 meters;
b) Ensure IKBT12 has entered pairing mode.
3. What to do when IKBT12 can’t be turned off?
Please charge the IKBT12 for about 2 seconds.
6
„ Specifications
Bluetooth version
Bluetooth profiles
Bluetooth frequency range
Operating distance
Charging input voltage/current
Standby time
Working time
Dimensions
Weight
Bluetooth V2.1
A2DP and AVRCP
2.402GHz-2.480GHz
10 meters, Class II
DC 5V
300mA
230 hours
Up to 12 hours
45×33×8mm
14g
Notes:
1. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement