zbzweugv1 - Zipabox User manual v1.2 (English version

zbzweugv1 - Zipabox User manual v1.2 (English version
ZIPABOX
USER
GUIDE
v1.2
How can I
manage all
security issues
with one
easy, intuitive
and efficient
solution?
CONNECT EVERYTHING
This guide
describes
how to install,
program and
operate Zipato
smart alarm
system.
02
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
COPYRIGHT
© 2012 Tri plus grupa d.o.o. All Rights Reserved. Copyright by Tri plus grupa d.o.o.
No part of this manual may be reproduced or transmitted in any form without the
expressed, written permission of Tri plus grupa d.o.o.
TRADEMARKS
Zipato and the Zipato logo are registered Trademarks.
All other product names mentioned herein may be trademarks or registered
trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the content of this manual,
it is possible that this document may contain technical inaccuracies, typographical,
or other errors. Zipato assumes no liability for any error in this publication, and
for damages, whether direct, indirect, incidental, and consequential or otherwise,
that may result from such error, including, but not limited to loss of data or profits.
Zipato provides this publication “as is” without warranty of any kind, either express
or implied, including, but not limited to implied warranties of merchantability or
fitness for a particular purpose. The published information in the manual is subject
to change without notice.
Zipato reserves the right to make changes in the product design, layout, and driver
revisions without notification to its users.
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
03
IMPORTANT SAFETY INFORMATION
To avoid contact with electrical current:
Never
install an Ethernet connection in wet locations unless that connector is
specifically designed for wet locations.
Do
not place Ethernet wiring or connections in any conduit, outlet or junction box
containing electrical wiring.
Installation of inside wire may bring you close to electrical wire, conduit, terminals
and other electrical facilities. Extreme caution must be used to avoid electrical
shock from such facilities. Avoid contact with all such facilities.
Ethernet wiring must be at least 2 m from bare power wiring or lightning rods and
associated wires, and at least 15 cm from other wire (antenna wires, doorbell
wires, wires from transformers to neon signs), steam or hot water pipes, and
heating ducts.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies with all the
requirements in respect of interference radiation according to EN 301 489-17, EN
301 489-1 and EN 300 328. The connections conducting HF signals must neither be
manipulated nor damaged.
04
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
CONTENTS
INTRODUCTION 05
PACKAGE CONTENTS
12
CONNECT THE ZIPABOX
13
ACCOUNT CREATION AND REGISTRATION
15
INSTALLATION/MOUNTING ZIPABOX
18
ADDING DEVICES
20
REMOVING DEVICES
20
TROUBLESHOOTING
21
SPECIFICATIONS
24
LIMITED PRODUCT WARRANTY
26
DECLARATION OF CONFORMITY
32
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
05
INTRODUCTION
THANK YOU for purchasing Zipabox smart home automation controller. This
guide describes how to install, program and operate your Zipabox. Zipabox makes
every home smart by using advanced technology to hide the complexity of home
networking - delivering a simple smart home. It plugs into any outlet in the home
and automatically talks to all the connected devices in the house, connecting them
to the cloud so that consumers can control them using tablets, smart phones,
computers or TVs— at home or on the go. The Zipabox Gateway supports a variety
of communication standards including Z-WAVE, ZIGBEE, KNX, ONVIF, and UPnP.
The Zipabox’s capabilities can easily be expanded using “snap-in” expansion
modules that will add support for new interfaces and functionalities, communication
standards and protocols, etc.
Once configured, the gateway works stand-alone, but also features cloud support
for advanced monitoring, messaging and programming services.
Intuitive graphical user interface allows customers to program their own home
rules without any previous programming experience.
06
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
01
SECURITY
AND SAFETY
unlimited number of virtual alarms (partitions)
up to 233 two-way, wireless zones
trigger alarms in case of:
intruder (motion sensors and door/window sensors),
fire (smoke sensors),
flood (water leakage sensors),
gas (CO sensors)
panic button,
duress (if someone force you to disarm your system)
health care (in case of missing actions during particular time e.g. motion, door
opening, laying on bed...)
remote arm/disarm and status-info with any smartphone
v andal
proof - Zipabox is 24/7 monitored by central station which triggers alarm
in case of connection loss
include arm/disarm commands in automation scenes
integration with existing alarm systems (DSC, Honeywell...)
easy online setup and configuration through web based interface
use of same sensors for security and automation purposes
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
07
02
LIGHTING
easy installation of wireless modules
Z-Wave and ZigBee lighting modules pre-configured for even easier setup
support remote dimming and on/off switching with any smartphone
automatically turn lights on at sunset and off at sunrise
unlimited number of scenes supported
turn lights on during emergencies
advanced event based rules configuration
auto-pilot lighting programs to discourage intruders while home is empty
03
CLIMATE
multi-room heating and cooling control with any smartphone
advanced programming scheduler online, accessible over web browser
easily create unlimited number of custom zones (thermostats)
multi-zone humidity control by using standard humidifiers and dehumidifiers
use Internet weather feeds to program your home climate conditions
create
advanced event based rules to automate home climate based on other
08
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
environmental and home events
include climate control in automation scenes together with alarm, lighting, etc.
Notification
and automated actions in case of overtemperature events, power
outages, and other incidents…
04
SUN
SHADING
control blinds, roller-shutters, curtains and pergolas using any smartphone
automate motors by using fun and easy programming
add
your sun shading commands into home scenarios together with lights,
climate, alarms...
automate your shades to react to outside weather conditions
easy installation using pre-configured wireless modules
05
IRRIGATION
control unlimited number of irrigation zones
use advanced programming options online to setup perfect irrigation process
automate irrigation system based on Internet weather forecast
www.zipato.com
integrate
ZIPABOX
QUICK INSTALLATION GUIDE
09
your irrigation scheme together with your complete home automation
scenarios
06
ACCESS
remotely lock/unlock your door with any smartphone
remotely open/close your garage door or gate over any smartphone
get video notification when door is open
use RFID tags to open doors and get detailed statistics
automate doors/locks using scenarios and event based programming tool
trigger automation events when door lock user codes are entered
automatically unlock doors in the event of an emergency
07
MULTIMEDIA
remotely control your audio/video equipment with any smartphone
automatically turn on favorite shows when they air and get alerts
automatically turn off A/V equipment at pre-set time or when room is unoccupied
automatically turn on equipment to discourage intruders
10
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
08
VIDEO
MONITORING
access live and recorded video via the web and from any smartphone
support for most of the available IP cameras – ONVIF support
get email and SMS notifications with pictures and live video attached
remotely adjust pan-tilt cameras
create advanced event based recording and video notification rules
09
ENERGY
METERING
real-time monitoring energy consumption and notification right on smartphone
compare energy usage and cost with others in the area
automatically turn on/off your appliances in accordance with electricity prices
see detailed analysis of your energy consumption
s ave energy by automating lights, thermostats, sun shades...
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please follow manufacturer’s
instructions. Be careful when using hand and power tools and follow the manufacturer’s
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
11
guidelines when using them. Take care that the correct tools are used. Wear goggles or
protective clothing where required.
08
TECHNICAL
SUPPORT
HAVING TROUBLE INSTALLING YOUR NEW PRODUCT?
Zipato’s website contains the latest user documentation and software updates for
Zipato products and services.
www.zipato.com
CALL SUPPORT
CONTACT LINE: + 385 1 444 444 00
(Mon-Fri) 9.00am-06.00pm
12
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
PACKAGE CONTENTS
USER
GUIDE
ZIPABOX
POWER ADAPTER
230V AC TO
12V DC
ETHERNET
CABLE
868 MHZ ANTENNA
FOR Z-WAVE
NETWORK
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
13
CONNECT THE ZIPABOX
Locate your serial number Your Serial number is located on the back of the Zipabox,
make a note of it as it will be required when registering your panel online.
CONNECT TO BROADBAND
Connect your Zipabox to your broadband router via the Ethernet cable.
The Ethernet port is located on the back of the Zipabox.
Zipabox queries your DHCP server for an IP address. If you do not have a DHCP
server in your local network, after 60 seconds Zipabox will auto configure itself with
link-local IPv4 address (in 169.254.0.0/16 range).
01
01
Serial
number
02
Antenna
1
03
Antenna 2
(optional)
04
Reset
button
05
Ethernet
port
06
Power
input
02
03
04
05
06
14
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
MOUNT ANTENNA
Screw Z-wave antenna to Antenna 1 connector
POWER UP
Plug the power adaptor into mains supply wall socket and the other end into control
unit. You should see following LED sequence:
01 | PLUG IN POWER ADAPTOR: steady yellow light for approximately 60 sec.
02 | ZIPABOX GETTING READY: slowly fl ashing green light
03 | ZIPABOX READY: steady green light
01
01
Button
1
02
Button
2
03
LED
indicator
02
03
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
15
ACCOUNT CREATION
AND REGISTRATION
ACCOUNT CREATION
To benefit from the Zipato monitoring and control service you will need to set up your
Zipato account and register your Zipabox. Upon registration you will automatically
get the basic free level of monitoring service.
Open a browser window on your computer and go to the following URL: my.zipato.com
Click on “Register” button in upper right corner of a screen and follow the onscreen
instructions. Next window will pop up.
Fill out empty fields
Click on “Register”
Take note of your password
during this process.
16
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
Once you input registration data and click on register, new window will pop up:
When this message appears check your email account. If there is no email please
check spam container.
Email should look like this:
Hi, your email here“, welcome to the Zipabox!
To validate your email address please click on the following link verify Once email is
verified, login to Zipato by filing out credentials.
REGISTER YOUR ZIPABOX
When you first time log in to your account, you need to enter serial number of your
Zipabox. Serial number is located on back of your Zipabox.
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
17
Enter the serial number located at back of your Zipabox
S erial
number must be entered within 2 min. If not, message will appear saying
“Allowed registration time elapsed”. This is done because security precaution. If
this happens restart Zipabox and reenter serial number.
FINALIZE YOUR ACCOUNT
Your account is set up and you are able to use Zipato cloud system. Anyway, you
need to ensure that your account is fully set up so you get the most from your Zipato
account. THIS INCLUDES: Account Details
Make sure that you have fully completed your profile. Go to General settings in the
General widget and select Details tab.
USERS
The Users section is where you add your family members which will have the rights
to use your system. Adding a new user requires you to enter new user’s details and to
give him/her certain rights. Rights management allows you to permit some services
for some users.
18
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
INSTALLATION/
MOUNTING ZIPABOX
WALL MOUNTING
Drill holes in the wall surface and insert the wall plugs if fixing into plaster or brick
holes. Drill two holes, fix the screws and hook the Zipabox onto the screw’s heads.
Make sure swivel antenna is in vertical position.
01
01
Holes
for fixing
Zipabox
on screw’s
heads
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
19
DIN RAIL MOUNTING
Make enough space for Zipabox on your Din-rail. Hook upper fitters on the back of
your Zipabox to the Din rail and press Zipabox slightly to snap lower fitters.
Upper
fitters
01
Lower
02
fitters
02
01
TABLE TOP
You can place your Zipabox on any table top. Just make sure that swivel antenna is
in vertical position.
Button
1
01
Button
02
2
02
LED
03
indicator
03
01
20
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
ADDING DEVICES
ADDING NEW DEVICES Z-WAVE OR ZIGBEE
Before adding new device, it is recommended to bring device closer to Zipabox, so
that no obstacle can interfere with operating range of device. Recommended distance
between sensors and Zipabox is less than one meter. Read device instructions
regarding inclusion/join mode. Device in inclusion/join mode is awake and ready
for joining in to Zipato network. Always reset device before adding it to the network.
Reset deletes any information about prior controller that was stored in device. At the
end of joining or removing session it is recommended to refresh Zipato Control Center
or wait until number of device is not increased by one to make sure that device is
visible in Total device list.
01 | On Zipato dashboard, click “Add device” button in General widget and follow
wizard instructions. For Zwave devices, it is recommended that you reset your
device before adding it to the Zipato network.
02 | After you successfully add the device in to your Zipato network go to “Total
devices” in General widget and set your device’s room name and type. This will help
you to control your device easier.
REMOVING DEVICES
To remove device go to Zipato Control Center and click on “Remove device” and
follow wizard instructions.
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
21
TROUBLESHOOTING
Waiting for more than a five minutes and still there is no green LED light.
01 | Check your Internet connection
02 | Check whether you connected your network cable correctly to your Internet router.
I forgot my password
01 | Go to my.zipato.com
02 | Click “Forgot password” and follow screen instruction.
I cannot connect any Z-wave or ZigBee device to my box
Check whether your antenna supplied with Zipabox is correctly mounted on Antenna
1 connector.
No Ethernet signal from Zipabox
Before connecting Zipabox check your internet connection. If everything is alright
with your internet connection then follow these steps:
01 | Unplug power and Ethernet cable from your Zipabox
02 | Wait 2 min.
03 | First plug in Ethernet cable and then power supply.
04 | P
ress and hold Button2 on your Zipabox and then briefly press (and release)
Reset button.
22
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
05 | K
eep holding Button2 for 5 seconds (and then release it).
06 | T
hen observe your LED sequence. If everything goes alright at the end there
should be fixed green light from LED.
If this won’t work it is obviously a hardware problem. In that case you should return
your box to your supplier and take the new one...
I
have placed a device outside my house and it is not communicating with the
Zipabox. What’s happening?
If you have a lot of metal in the exterior construction of your home, this could
significantly impede wireless communication. Metal is an insulator of radio signals. If
your house has metal siding or a stucco finish over a metal mesh, you may have range
problems on devices outside your home communicating with the Zipabox inside.
What should I do if I am having trouble installing my device?
If you are having difficulty with the physical installation of non-Zipato branded
devices (Thermostats, GE switches, Blueline meter reader, etc.), please contact the
manufacturer directly for assistance.
If you are having trouble pairing a device to the Zipabox, check the videos or other
content on Zipato website for assistance.
Error “Validation time expired”
Serial number must be entered within 2 min. If not, message will appear saying
“Allowed registration time elapsed”. This is done because security precaution. Allowed
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
23
registration time starts ticking away after Zipabox establishes connection with the
cloud server after power up/reset. So just reset your Zipabox, wait for the light to turn
steady green, and the login into the cloud application and enter the serial number.
I have added device to Zipabox, but is not working properly?
If your device is not working properly try to reinstall it again. Make sure when adding
new device that join procedure is completed. If join procedure is successful you will
get message “Device joined” and Close button will appear.
What happens when adding new device is interrupted?
If device shows up in total devices window, delete it and then add this device again. If
that device is not shown in total devices window just add this device again.
Do not forget to synchronize
When doing changes with your device like changing endpoint name, configuration or
any change regarding devices and their endpoints, remember to click on synchronize.
Does Zipato offer a warranty?
See the Limited Product Warranty for specifics of the Zipato service warranty.
24
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
SPECIFICATIONS
SYSTEM
Antenna Zigbee (option)
ARM9 208MHz CPU
32MB RAM
128MB Flash
POWER
Power input: 9-12VDC
Power supply input: 100-240VAC,
NETWORK
Ethernet
50/60Hz
Power usage: Idle: 1.2W, Max: 2.4W
Z-Wave (US or EU)
ZigBee (802.15.4) (option)
I/O & LEDS
2 programmable buttons
OPERATING SYSTEM
Linux 2.6 Kernel
2 programmable green LEDs
1 programmable RGB LEDs
Power, Status, Ethernet, WLAN &
PHYSICAL DIMENSION
Z-Wave
86 (L) x 8 (W) x 4 (H) millimeters
34(L)x34(W)x19(H) inches
ACCESSORIES
REGULATORY COMPLIANCE
(PENDING)
Safety: UL
CAT5e UTP patch LAN Cable
EMC: FCC, CE
Antenna Z-wave
RoHS
www.zipato.com
AUTOMATION OPTION
ZIPABOX
QUICK INSTALLATION GUIDE
25
Storage: -25°C to 70°C (-13°F to
Remote automation software
158°F)
Online remote control interface
Humidity: 5% to 95% noncondensing
ENVIRONMENTAL
WARRANTY
Temperature Range:
1 year standard
Operating: 0°C to 40°C (32°F to
Specifications are subject to change
104°F)
without prior notice
26
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
LIMITED PRODUCT
WARRANTY
GENERAL TERMS
Nothing in this Limited Product Warranty affects your statutory rights as a consumer.
The Limited Product Warranty set forth below is given by Tri plus grupa d.o.o.
(Europe) (herein referred to as “ZIPATO”). This Limited Product Warranty is only
effective upon presentation of the proof of purchase. Upon further request by
ZIPATO, this warranty card has to be presented, too.
EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, ZIPATO MAKES
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
ZIPATO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE
LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY
STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES AGAINST
ZIPATO. THEY DO NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU
HAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM. IN NO
EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR INDIRECT, SPECIAL,
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
27
INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER
DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
HOWEVER, NOTHING IN THIS AGREEMENT LIMITS ZIPATO’S LIABILITY TO YOU
(I) IN THE EVENT OF DEATH OR PERSONAL INJURY TO THE EXTENT RESULTING
FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART OF ZIPATO, OR (III)
TO THE EXTENT ARISING UNDER PART 1 OF THE CONSUMER PROTECTION ACT
1987 OF THE UNITED KINGDOM. SOME STATES OR COUNTRIES DO NOT ALLOW:
(1) A DISCLAIMER OF IMPLIED WARRANTIES; (2) A LIMITATION ON HOW LONG AN
IMPLIED WARRANTY LASTS OR THE EXCLUSION; OR (3) LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS. IN SUCH STATES OR
COUNTRIES, SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY
NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE OR
FROM COUNTRY TO COUNTRY. YOU ARE ADVISED TO CONSULT APPLICABLE STATE
OR COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.
This Limited Product Warranty applies to ZIPATO branded hardware products
(collectively referred to as “ZIPATO Hardware Products”) sold by ZIPATO (Europe),
its European subsidiaries, affiliates, authorized resellers, or country distributors
(collectively referred to as “ZIPATO Resellers”) with this Limited Product Warranty.
The term “ZIPATO Hardware Product” is limited to the hardware components and all
its internal components including firmware. The term “ZIPATO Hardware Product”
DOES NOT include any software applications or programs.
28
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
GEOGRAPHICAL SCOPE OF THE LIMITED PRODUCT WARRANTY
This Limited Product Warranty is applicable to Hardware Products sold by Zipato
Resellers in all countries listed at the beginning of this document under the heading
“Countries in which this ZIPATO Limited Product Warranty applies”. The Limited
Product Warranty will be honored in any country where ZIPATO or its authorized
service providers offer warranty service subject to the terms and conditions set
forth in this Limited Product Warranty. However, warranty service availability
and response times may vary from country to country and may also be subject to
registration requirements.
LIMITATION OF PRODUCT WARRANTY
ZIPATO warrants that the products described below under normal use are free
from material defects in materials and workmanship during the Limited Product
Warranty Period set forth below (“Limited Product Warranty Period”), if the product
is used and serviced in accordance with the user manual and other documentation
provided to the purchaser at the time of purchase (or as amended from time to time).
ZIPATO does not warrant that the products will operate uninterrupted or error-free
or that all deficiencies, errors, defects or non-conformities will be corrected.
This warranty shall not apply to problems resulting from: (a) unauthorized
alterations or attachments; (b) negligence, abuse or misuse, including failure to
operate the product in accordance with specifications or interface requirements;
(c) improper handling; (d) failure of goods or services not obtained from ZIPATO
or not subject to a then-effective ZIPATO warranty or maintenance agreement; (e)
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
29
improper use or storage; or (f) fire, water, acts of God or other catastrophic events.
This warranty shall also not apply to any particular product if any ZIPATO serial
number has been removed or defaced in any way.
ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT OF YOUR
FAILURE TO FOLLOW THE INSTRUCTIONS FOR THE ZIPATO HARDWARE PRODUCT.
LIMITED PRODUCT WARRANTY PERIOD
The Limited Product Warranty Period starts on the date of purchase from ZIPATO.
Your dated sales or delivery receipt, showing the date of purchase of the product, is
your proof of the purchase date. You may be required to provide proof of purchase
as a condition of receiving warranty service. You are entitled to warranty service
according to the terms and conditions of this document if a repair to your ZIPATO
branded hardware is required within the Limited Product Warranty Period.
[Other than in respect of products for domestic use (in particular those listed in
the first and last boxes in the table below), this Limited Product Warranty extends
only to the original end user purchaser of this ZIPATO Hardware Product and is not
transferable to anyone who obtains ownership of the ZIPATO Hardware Product
from the original end-user purchaser.
30
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
PRODUCT WARRANTY PERIOD TABLE
PRODUCT TYPE
Product Warranty Period
ZIPABOX CONTROLLER
One (1) year
IMPORTANT: The content of “Product Type” listed above is subject to change; please
refer to the www.zipato.com for latest update.
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
31
PERFORMANCE OF THE LIMITED PRODUCT WARRANTY
If a product defect occurs, ZIPATO’s sole obligation shall be to repair or replace
any defective Zipato Hardware Product free of charge provided it is returned to an
Authorized ZIPATO Service Centre during the Limited Warranty Period. Such repair
or replacement will be rendered by ZIPATO at an Authorized ZIPATO Service Centre.
All component parts or hardware products that are replaced under this Limited
Product Warranty become the property of ZIPATO. The replacement part or product
takes on the remaining Limited Warranty Period of the replaced part or product.
The replacement product need not be new or of an identical make, model or part;
ZIPATO may in its discretion replace the defective product (or any part thereof) with
any reconditioned equivalent (or superior) product in all material respects to the
defective product.
WARRANTOR
Tri plus grupa d.o.o.
Banjavciceva 11
10 000 Zagreb
CROATIA Telephone +385 (1) 444 444 00
Facsimilie +44(0)208 955 9001
32
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
DECLARATION OF
CONFORMITY
The Manufacturer Tri plus grupa d.o.o. hereby declares that the product:
Zipabox Smart home controller 1 (zbzweugv1)
In accordance with the following Directive(s): 2006/95/EC The Low Voltage
Directive, 89/336/EEC The Electromagnetic Compatibility Directive and 1999/5/
EC R&TT EC Directive is in conformity with the e applicable requirements of the
following documents:
EN 61326
EN 61000-3-3
EN 61000-4-4
EN 61000-4-11
IEC/EN 55011
EN 61000-6-2
EN 61000-4-5
EN 301 489-1-3
EN 300 220-2
EN 61000-4-2
EN 61000-4-6
AS/NZS/IEC 60335-2-97
EN 61000-3-2
EN 61000-4-3
EN 61000-4-8
EN 60335-1
I hereby declare that the equipment named above has been designed to comply with
the relevant sections of the above referenced specifications. The unit complies with
all applicable Essential Requirements of the Directives.
PERSON RESPONSIBLE FOR THIS DECLARATION:
Dean Janacek, Certification Manager
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
33
Changes or modifications not expressly approved Tri plus grupa d.o.o. for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
34
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
www.zipato.com
ZIPABOX
QUICK INSTALLATION GUIDE
35
DISPOSING AND RECYCLING YOUR PRODUCT
This symbol on the product or packaging means that according to local laws and
regulations this product should be not be disposed of in the household waste but
sent for recycling. Please take it to a collection point designated by your local
authorities once it has reached the end of its life, some will accept products for free.
By recycling the product and its packaging in this manner you help to conserve the
environment and protect human health. Zipato and the environment At Zipato, we
understand and are committed to reducing any impact our operations and products
may have on the environment. To minimize this impact Zipato designs and builds its
products to be as environmentally friendly as possible, by using recyclable, low toxic
materials in both products and packaging.
36
ZIPABOX
QUICK INSTALLATION GUIDE
www.zipato.com
we make every home smart
www.zipato.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement