V-Tec 27TD7-V1 User manual

Add to My manuals
12 Pages

advertisement

V-Tec 27TD7-V1 User manual | Manualzz
ENGLISH
2 WIRE INTERCOM SYSTEM
USER MANUAL
Q
( — N
Main Menu =
UNLOCK
с
м
J
N cocooo>
=== |
N J
PM-D271T
1. Parts and Functions
Key functions
LCD Touch Screen
Microphone
CALL button
Monitor … UNLOCK button
Manual Monitor TALK/MON button
Intercom LED indicator
User Setup
Close
Speaker
NJ
000000
IN
o®
000000
@e
e Ventilation Vent
— H
Г ® Mounting Hook
(i
BE e Connection Port
=> a e Mounting Hook
LCD screen Display the visitors' image
LED Indicator Show the working status of monitor
Unlock button Press to release the door
Call button Press to activate intercom function
Talk/Mon button [Press to communicate hands free with visitor
Press to view the outdoor condition in standby mode
Microphone Receive voice from the user
Mounting hook Use to hang up the monitor
Connection port Bus terminal
Speaker Send out vioce from the visitor
2. Monitor Mounting
y 7 7
V 7 +4
©
\ RAR à
145-160
x x N x N x N x N x x N x
ON NN NN NN NN NN
NM OO N
NON У У У У Хх Хх Ух “ “IN
my
N
N
N
8 °F 7 * Fe $ €
/
1. Use the screws to fx the Mounting Bracket on the mounting box.(ftting accesories
includes a Bracket (Two pieces of 4X25 screws are needed for fastening the
Mounting Bracket), Special 2 wire cables to connect with Monitor)
2. Wire the system correctly(see the later connection chapter) then hang the Monitor
on the Mounting Bracket frmly.
3. Main Menu
1. Touch the screen anywhere on monitor in standby mode, the date/time page will be
showed. (the date/time page will be closed in 1 minute if no operation)
2. Touch the screen again, main menu page will be showed as follows.
Main Menu
12/28/2010 Na UA Monitor ...
Manual Monitor
0 6 | 4 4 — — — > Intercom
Ё АМ
User Setup
Close
4. Basic Door Release Operation
1. Press CALL button on outdoor station, the i
Monitor rings, at the same time, the screen €
displays the visitor image.
2. Press TALK/MON Button on monitor or touch |
[4] icon on screen, you can communicate hands a
free with the visitor for 90 seconds.After fnishing
communication,press TALK/MON button again
or touch icon to end the communication. If nobody answers the phone, the
screen will be turned off automatically after 30 seconds.
3. During talking state, Press UNLOCK Button or touch or icon to open the
corresponding door for the visitor.
4. When the monitor is in standby mode, press TALK/MON Button(or touch
Monitor ... item on main menu page), The screen can display the view of outside.
If multi door stations are installed, touch icon to get into the camera switch
mode(or direct touch Manual Monitor item on main menu page). You can touch
camera 1/2/3/4 to monitor the door station or CCTV camera you want.See the
following diagrams.(Press TALK/MON button again to end monitoring.)
Monitor Select
' Camera 1 ...
> Camera 2 ...
E > Camera 3 …
| Camera 4 ...
| Monitor Time Set ...
3 9 Exit (m) Home
5. Intercom Function Intercom
Intercom Call ...
When the monitor is in standby mode, press CALL Inner Call ...
Button to enter Intercom Function page(or direct
touch Intercom item on main menu page).
Direct Call Guard Unit ...
9 Exit (@ Home
1. Intercom Call: User in one apartment can call other apartments in the system. the
namelist will be created automatically by the system. Touch a name you want on
the screen, then touch © icon or press CALL Intercom Call
Button on monitor to dial.(Note:1. touch © icon Jim. Zhang
or press CALL button again to redial. 2. Press Jacko. Zhang
TALK/MON button to cancel the call. 3.The Hobo Zhang
DIP switches code of each monitor must set Eu
different ) 9 Exit (© Calling » Next Page
2. Inner Call: If multi Monitors are installed in the
same apartment, select Inner Call, all the other Monitors will ring at the same time,
whichever Monitor answers the call, conversation is started.and the other monitors
will stop ringing at the same time.(note:the DIP switches setting of all monitors
must be same. )
3. Direct Dial Guard unit: A Monitor can be assigned as Guard Unit Monitor; when
the Guard Unit Monitor answers the call, conversation with the guard person is
started..
6. Basic Setup Instructions
Ring Tone Settings
Touch User Setup item on main menu page to enter setup page. Touch Door Station Call
Tone, Inercom Call Tone or DoorBell Tone item, There are 12 pieces ring tones can be
selected.touch a ring tone you want, then touch icon to save and exit.(touch © icon
to cancel the setting and return last page, touch {n) icon to get into main menu page)
Door Station Call Toneset the ring tone calling from outdoor station.
Intercom Toneset the ring tone calling from other apartments.
DoorBell toneset the ring tone calling from door bell.
Door Station Call Tone
Selected: 06
User Setup (1)
Door Station Call Tone ...
Intercom Call Tone ...
DoorBell Tone ...
Clock …
Next Page
9 Exit (@ Home
у
© Cancel {M Home Save&Exit
Ring Volume and Night Ring Volume Setting
You can set a ring volume for day time and night
time individually, 6:00 AM-18:00 PM 1s the day
time and 18:00 PM~6:00 AM is the night time by
default,if you don't want to be disturbed at night,you
can set the night ring volume to 0.
Touch User Setup item on main menu page to
enter setup page,then touch Next Page item to enter
User Setup 2 page, select Ring Volume Settingor
Night Ring Volumeitem. then touch А / V icon to
increase / decrease the value; After finish, touch
icon to save and exit.(touch 9 icon to cancel the
setting and return last page, touch {n) icon to get into
main menu page)
7. Date and Time Setting
Touch User Setup item on main menu page to enter
setup page, touch Clock... item. a digital keypad
Will be showed on screen, input date and time by
touching the digital keypad,use * icon to move the
location. After finish, touch icon to save and
exit.(touch 9 icon to cancel the setting and return
last page.)
8. Monitor Time settig
Touch Manual Monitor item on main menu page
to get into camera switch mode, select Monitor Time
Set... item. touch A / Y icon to increase / decrease
the value; After fnish, touch icon to save and
exit.(touch 9 icon to cancel the setting and return
last page, touch (n) icon to get into main menu page)
User Setup (2)
Ring Volume ...
Night Ring Volume ...
TPC Confgure ...
Restore to default ...
Last Page
9 Exit (@ Home
Ring Volume
A
Current : 05
У
© Cancel (M) Home Зауе&Ехй
2010-12-28 15 : 00
(1)(2)(3)
[4 (5)(6]
(7](8][9]
[+ [0)[#)
9 Cancel Save&Exit
Monitor Time Select
A
Current : 01min
У
9 Cancel (в) Home [iF] Save&Exit
9. Restore to Default
Touch User Setup item on main menu page to enter setup page,then touch Next Page
item to enter User Setup 2 page, touch Restore to defaultitem ,a message will be asked
to confirm the restore operation. If touch icon ,All settings will be restored to
default, if you don't want to restore, touch © icon to cancel the operation.(Note that the
restore to default operation will not change the time setting and the datas.)
User Setup (2)
Ring Volume ...
Night Ring Volume ...
Restore to Default
Are you sure to
TPC Confgure ...
Restore to default ...
Last Page
5 Exit (@ Home
Restore all to default?
у
© Cancel OK
10. Monitor Parameter Setting
How to enter the installation setting page
Main Menu HW: DT14-CT a1ß
Monitor … S/W: V17.11.418.0D
Manual Monitor Une ina: |
Intercom ts mate _ — — > [9]
User Setup Video standard: - (+ ](0)(#]
Close Language:
(1) About
1.Touch () About item 2.Touch the screen 3.A digital keypad
on main menu page. anywhere and hold for Will be showed.
2s.
How to set the monitor as a Guard Monitor
A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor
answers the call, conversation with the guard person is started..
The code number of 8004 1s used to set the monitor as a guard unit monitor and 8005 is
used to cancel this function.
How to set the slave monitor address
Maximum 4 monitors can be connected in one apartment,one master monitor together
with 3 slave monitors, so you should set the address correctly.(note:must have one
monitor to be set as master monitor)
The code of 8000 is used to set the master monitor.
The code of 8001 is used to set the frst slave monitor .
The code of 8002 is used to set the second slave monitor .
The code of 8003 is used to set the third slave monitor .
Note:touch * button to cancel the input,touch # to save the settings.
How to set date and time format
The system offers two methods of date and time.
The code number of 8008 is used to set the date format as month/date/year
The code number of 8009 is used to set the date format as date/month/year
The code number of 8012 is used to set the time format as 12 hour system
The code number of 8013 is used to set the time format as 24 hour system
How to set the monitor panel on
In default mode,when receive a calling,the master and slave monitors will ring at the
same time,and just the master monitor can display the image while the slave monitors
can not.But the settings can be changed,you can set the master monitor and all the slave
monitors to panel on at the same time when receiving a call, just input the code number
of 8006 on each slave monitor.
2TGUUECNNDWVVQP
QPFQQTUVCVKQP 9JGPTGXGKXKPIECNNKPICNNOQPKVQTUECPFKURNC[VJGKOCIGCWJGUCOGVKOG
/CUVGTOQPKVQT UVUNCXGOQPKVQT PFUNCXGOQPKVQT TFUNCXGOQPKVQT
How to set the unlock parameter
Unlock mode:
There are two unlock modes: 1.power-on- to-unlock type:unlock mode=0(by default)
2.power-off-to-unlock:unlock mode=1.
The code number of 8010 1s used to set the unlock mode to 0
The code number of 8011 1s used to set the unlock mode to 1
Unlock time:
The unlock time can be changed by yourself at any time.it can be set from 1 to 9 seconds.
The code number from 8021 to 8029 are used to set the unlock time to 1~ 9 seconds.
How to set the menu language
The monitor can support multi languages and it is so simple and fast, just input the
corresponding language code on monitor. The language code number are as follows:
8101: English 8107: Portuguese 8113: Russian
8102: French 8108: S-Chinese 8114: Slovakia
8103: Spanish 8109: T-Chinese 8115: Hungray
8104: Italian 8110: Greek 8116: Czech
8105: German 8111: Turkish
8106: Dutch 8112: Polish
Note:the monitor can only support 4 types of languages.English,French,Spanish and
German are default.But you can customize any 4 languages by yourself. The language
which is unavailable will be set to English in default.
11. Screen and Volume Adjustment
During monitoring or talking, touch icon,the ADJUST MENU will be displayed.
Touch and select the adjustment item you want; touch « / » icon to decrease / increase
the value.
1. The first item is Scene mode selection: Total 4
screen modes can be selected in sequence: Normal,
User, Soft and Bright. Whenever you modify
Brightness or colour, Scene item will be set to User
mode automatically.
2. The Brightness and Colour item is for the image
quality setting, adjust the value to get the best
image you like.
Scene
Bright
Color
Ratio
Talk Volume
© Exit Dec< > Inc
3. The Ratio item is for screen display adjustment,you can set to 16:9 or 4:3.
4. The Talk Volumeitem is for talking volume adjustment.
5. Note that all the modifcations will be performed immediately after the operation.
Touch 9 icon to exit the adjust page.
12. Specifcation
e Power supply for indoor monitor: DC 24V
e Power consumption: Standby 1.5W; Working status 10W
e Monitor screen: 7 Inch digital color LCD
e Display Resolutions: 800*3(R, G, B) x 480 pixels
e Video signal: 1Vp-p, 750, CCIR standard
e Wiring: 2 wires, non-polarity
e Dimension: 155(Н) x 225 (W) x 28(D)mm
10
The design and specifications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved.

advertisement

Related manuals

Download PDF

advertisement