null  null
4-CH Network Video Recorder
NVR-400
User’s Manual
Version: 1.0
Copyright
Copyright (C) 2009 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology,
This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form by any means by electronic or mechanical. Including
photocopying, recording, or information storage and retrieval systems, for any purpose other than the
purchaser's personal use, and without the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty and representation, either implied or expressed, with respect to the
quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for
any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment
on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep current the information in this User’s
Manual, and reserves the right to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE mark Warning
The is a class A device, In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous
hardware and software products by their trade names. In most, if not all cases, these designations are
claimed as trademarks or registered trademarks by their respective companies.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Revision
User’s Manual for PLANET 4-CH Network Video Recorder
Model: NVR-400
Rev: 1.0
Part No.: EM-NVR400
-1-
NVR-400 User Guide
P REFACE
Thank you for purchasing the Network Video Recorder, an IP based device that installed on your
network, which can be managed remotely via the Internet or your LAN. Together with the Internet
camera, the Network Video Recorder allows you to remote access and simultaneous record live
video streams.
The Network Video Recorder is easy to install and use. Simply connect it to the router/switch
within your network, and the device will automatically access to the connected camera(s) by
default IP protocol.
This User Guide provides you with the instructions and illustrations on how to use your Network
Video Recorder, which includes:
Chapter 1 Introduction to Your Device describes the components and features of the device.
Chapter 2 Hardware Installation helps you install the device according to your application
environment.
Chapter 3 Accessing the Device lets you start using your device without problem. The device
can be set up easily and work within your network environment instantly.
Chapter 4 Configuring the Device guides you through the configuration of the device using the
Web browser on your PC.
Appendix Provides the specifications of the device.
NOTE
The illustrations and configuration values in this guide are for reference only. The actual settings
depend on your practical application of the device.
4-CH Network lVideo Recorder
-2-
Table of Contents
P R E F A C E ........................................................................................................ 2
C H A P T E R 1 I N T R O D U C T I O N T O Y O U R D E V I C E ......................................................... 4
1.1 CHECKING THE PACKAGE CONTENTS ........................................................................................4
1.2 FEATURES AND BENEFITS .........................................................................................................4
1.3 GETTING TO KNOW YOUR DEVICE .............................................................................................5
C H A P T E R 2 H A R D W A R E I N S T A L L A T I O N .................................................................. 7
2.1 NETWORKING APPLICATION ......................................................................................................7
2.2 INSTALLING THE HARD DISK DRIVE ............................................................................................8
2.3 CONNECTING THE NETWORK ....................................................................................................9
2.4 CONNECTING THE POWER ADAPTER..........................................................................................9
C H A P T E R 3 A C C E S S I N G T H E D E V I C E .................................................................. 10
3.1 ACCESSING THE DEVICE VIA MY NETWORK PLACES ..................................................................10
3.2 USING IPFINDER ...................................................................................................................11
C H A P T E R 4 C O N F I G U R I N G T H E D E V I C E ............................................................... 14
4.1 USING THE SETUP WIZARD .....................................................................................................15
4.2 USING THE WEB CONFIGURATION UTILITY ...............................................................................17
A P P E N D I X ..................................................................................................... 38
SPECIFICATIONS ...........................................................................................................................38
HOW TO FAST ACCESS THE RECORDING FILES..................................................................................39
-3-
NVR-400 User Guide
C HAPTER 1 INTRODUCTION TO YOUR DEVICE
1.1
Checking the Package Contents
Check the items contained in the package carefully. You should have the following:
1 x NVR-400
1 x Power Cord
1 x Power Adapter
1 x RJ-45 Cable
4 x Rubber Pad
4 x Screw
1 x User’s Manual CD-ROM
1 x Quick Installation Guide
NOTE
Once any item contained is damaged or missing, contact the authorized dealer of your locale.
1.2
„
„
„
„
„
„
„
„
„
Features and Benefits
Simultaneous Record and Live Video Streams
4 IP Cameras Manual or Schedule Recording
Web-based Administration for Easy Configuration
Provides FTP, UPnP Media, iTunes Server
2 USB Ports for External Backup and Printer
Supports RAID 0, 1 and JBOD
Equips with Gigabit Ethernet Port
Provides Multiple Languages
Firmware Upgradable
4-CH Network lVideo Recorder
-4-
1.3
Getting to Know Your Device
„ Front Panel
Power Button
Unmount Button
USB Port 1
LED Icons
Item
1/2
Description
Press to turn on the device. Press and hold for about five seconds to turn off.
When you press the button to boot, the button start blinking Blue, and then
becomes a steady Blue when the device is ready.
Press to safely remove the connected USB device on the USB Port 1.
Connect the external USB backup device.
The LED icons on the front panel let you know the related status of your device.
See the following table for more information of the LED icons.
Description
A steady Green (1000 Mbps) or Amber (10/100 Mbps) light indicates the device
is connected to your LAN.
When it blinks, the device is receiving/ transmitting data from/to the network.
A steady Green light indicates the hard disk drive is installed in the device. A
blinking Green light indicates the installed hard disk drive is reading/writing data.
A steady Amber light indicates the hard disk drive is complete full (100%). A
blinking Amber light indicates the hard disk drive is getting full (95%).
1/2
The LED off indicates no USB devices is connected to the device. When you
connect the USB device to the device, the LED becomes a steady Green light.
When it blinks, the device is receiving/ transmitting data from/to the USB device.
Power Button
Unmount Button
USB Port 1
LED Icons
Icon
-5-
NVR-400 User Guide
„ Rear Panel
Fan and Ventilator
Reset
DC 12V
USB Port 2
Item
DC 12V
USB Port 2
Ethernet
Reset
Fan and Ventilator
4-CH Network lVideo Recorder
Ethernet
Description
Plug the provided AC Power Adapter.
Connect the USB printer (non-GDI interface).
Plug the provided Ethernet Cable to connect to your LAN.
Press to reset the device. Press and hold for about five seconds to
resume the factory default configuration.
Do not block or cover the ventilator for air circulation.
-6-
C HAPTER 2 H ARDWARE I NSTALLATION
2.1 Networking Application
The following diagram explains the application of the Network Video Recorder within your network.
In the illustration below, the Network Video Recorder and four Internet cameras are connected to a
router/ switch, which minimize the impact of the network traffic for the users within the network.
Network Video Recorder in your networking environment
-7-
NVR-400 User Guide
2.2 Installing the Hard Disk Drive
1. Disconnect the power cable of the device.
2. Remove two screws on the rear panel, and then remove the rear panel.
3. Pull the disk tray out until it jammed in the rack.
4. Place the hard disk drive on the tray, and then secured the screws on both side.
HDD 1
HDD 2
NOTE
While placing the hard disk drive onto the tray, align the screw holes on the bottom of hard disk drive with
the studs on the base of tray. The two studs are designed to ensure the hard disk drive will be installed on
the bracket securely.
5. Push the tray into the disk bay all the way until it connects the device.
6. Replace the rear panel and secure two screws.
4-CH Network lVideo Recorder
-8-
2.3 Connecting the Network
Plug an Ethernet cable to the LAN connector located on the device’s rear panel, and then connect
it to the network or directly to a computer for configuration.
Connecting the LAN cable
2.4 Connecting the Power Adapter
Plug the AC power adapter to the power connector located on the device’s rear panel, and then
connect it to your local power supply.
Connecting the power cable
-9-
NVR-400 User Guide
C HAPTER 3 A CCESSING T HE D EVICE
3.1 Accessing the device via My Network Places
Since you have built a connection between the Network Video Recorder and your PC, you can
easily access the device via My Network Places.
1. On your PC, click Start > My Network Places.
2. Find the device with its device named (such as NVR-400) in My Network Place.
3. Double-click the device icon. When the login window appears, enter the User name (the default
is admin) and password (the default is admin), and then click OK to access the Network Video
Recorder.
4-CH Network lVideo Recorder
- 10 -
3.2 Using IPFinder
The device comes with a conveniently utility, IPFinder, which is included in the Installation CDROM, allowing you to search the device on your network easily. The following instructions are how
to install the IPFinder software.
1. Insert the bundled CD-ROM into your computer’s CD-ROM Drive to initiate the Auto-Run
program. It will show you a web page.
2. Click the IPFinder hype-link to install this utility. If you don’t see the web page, you can find the
IPFinder in F:\utility\IPFinder, suppose F is your CD-ROM.
3. If you didn’t install .Net Framework 2.0 before, it will help you install first.
4. When you complete installing .NET Framework, you will continue to install the IPFinder.
Please click Next.
- 11 -
NVR-400 User Guide
5. Fill the customer information and click Next.
6. Click Install to begin the installation.
7. Click Finish to finish the installation.
4-CH Network lVideo Recorder
- 12 -
8. When you finish the installation, you can find IPFinder in Start Menu > All Programs > PLANET
> Planet NVR > IPFinder. You can also find the shortcut on desktop as below.
9. Launch the IPFinder, the control panel will appear as below.
Display the connected device(s).
Double click to link the device.
Click About to get the Version information of IPFinder.
Click Link to connect the selected device via Web browser.
Click Change IP to modify the IP address of the selected device.
Click Search to find the IP address of the connected device(s).
Click Exit to close the utility.
- 13 -
NVR-400 User Guide
C HAPTER 4 C ONFIGURING T HE D EVICE
You can easily access and manage the Network Video Recorder via the Web browser of your PC.
This chapter describes the Web Configuration Utility, and guides you through the configuration of
the device.
Since the default configuration of the device is DHCP mode enabled, you are recommended to
use IPFinder to search the IP address that is assigned to the device by the DHCP server, and then
click Link to access the camera via the Web browser.
Login the Homepage
The Web management allows you to access and manage the Network Video Recorder easily.
Launch the Web browser and then enter the IP address. The default IP address is 192.168.0.100.
And, fill the User Name and Password to login the Web management. The default User Name /
Password is admin / admin.
Web Configuration Utility of the device
4-CH Network lVideo Recorder
- 14 -
4.1 Using the Setup Wizard
The device’s Setup Wizard lets you configure your device easily and quickly. The wizard will guide
you through the necessary settings step-by-step.
To start the wizard, click Setup Wizard in the menu bar.
Step 1. LAN Setup
z Enter the Hostname for the device.
z Select Start UPnP to enable the device’s Universal Plug and Play function.
z If your network uses a proxy server, select Use proxy and enter the IP/Port values.
Step 2. TCP/IP Setup
z Select DHCP when your network uses the DHCP server; or select Static IP to assign the IP
address for the device directly.
For more information of TCP/IP settings, refer to the Lan section in Web Configuration
Utility.
- 15 -
NVR-400 User Guide
Step 3. Set up Space Type
z Select Single Disk or RAID for storing the files.
For more information of space type, refer to the Storage Setup section in Web Configuration
Utility.
Step 4. Setup Summary
z Display the configuration of the device.
When you complete the Setup Wizard, click Apply to reboot the device. Otherwise, click Back to
go back to the previous step(s) and change the settings.
4-CH Network lVideo Recorder
- 16 -
4.2 Using the Web Configuration Utility
After completing the Setup Wizard and rebooting the device, you can start to use the Network
Video Recorder within your network environment. However, you can configure the advanced
settings through the Web Configuration Utility.
The utility contains the following options in the menu bar: System Information, System, Storage
Setup, Authorization Setup, Network Service, NVR, Schedule Download, Logout, and Help.
Each option provides several related settings in the sub-menu area. Click the desired option from
the menu bar and then select the related setting to set up.
Sub-menu
Menu bar
4.2.1 System Information
The System Information menu displays the current configuration and events log of the device.
„ Summary
This sub-menu displays the hostname and IP address of the device, the date and time, and the
network service that you have set up.
- 17 -
NVR-400 User Guide
„ Status
This sub-menu displays the firmware version of the device, the networking information, the time
zone, and the disk information.
„ Log
This sub-menu displays the events log recorded by the system.
4-CH Network lVideo Recorder
- 18 -
4.2.2 System
The System menu contains the basic system settings for the device, such as the networking
settings, time and date setup, etc.
„ Lan
- 19 -
NVR-400 User Guide
z LAN Setup
- Hostname: Enter a descriptive name for the device.
- Start UPnP: The device supports UPnP (Universal Plug and Play), which is a set of
computer network protocols that enable the device-to-device interoperability. In addition, it
supports port auto mapping function so that you can access the device if it is behind an
NAT router or firewall. Select the Enable option to enable this feature.
- Use proxy: If your network uses a proxy server, select the Use proxy option and then
enter the IP/Port values.
z TCP/IP Setup
- DHCP: Select this option when your network uses the DHCP server. When the device
starts up, it will be assigned an IP address from the DHCP server automatically.
- Static IP: Select this option to assign the IP address for the device manually. You can use
IPFinder to obtain the related setting values.
IP Address
Subnet Mask
Gateway
DNS 1/2
Enter the IP address of the device. The default setting is:
192.168.0.100.
Enter the Subnet Mask of the device. The default setting is:
255.255.255.0.
Enter the default Gateway of the device. The default setting
is: 192.168.0.254.
DNS (Domain Name System) translates domain names into
IP addresses. Enter the Primary DNS and Secondary DNS
that are provided by ISP.
z Link Status
Display the connection status of the device.
„ Time
4-CH Network lVideo Recorder
- 20 -
z Time Zone
Select the proper time zone for the region from the pull-down menu.
z NTP Setup
Select this option and the time will be synchronized with the NTP Server. When you select
this option, you have to enter the IP address of the NTP server.
z Manual Setup
Select this option to set the date and time manually.
z Get time from my computer
Click the button and the date & time settings of the device will be synchronized with the
connected computer.
Once you complete the time and date setup, click Apply.
„ Notification
This sub-menu contains the required settings for e-mail notification feature. When you
complete the settings, click Send a test mail to test the related configuration is correct or not.
Once the device connects to the server successfully, click Apply.
z SMTP Server
Enter the mail server (e.g. mymail.com) in the box. Then, select the Authorization check
box and complete the following settings:
- User ID: Enter the user name to login the mail server.
- Password: Enter the password to login the mail server.
- Confirm Password: Enter the password again for confirmation.
z Sender E-mail
Enter the email address of the user (e.g. [email protected]) who will send the email.
z Primary/Secondary E-mail
Enter the first and second email address of the user who will receive the email.
- 21 -
NVR-400 User Guide
„ Configuration
z Delete all files
Select this option and click Apply to delete all files stored on the installed hard disk drives.
z Format all disks and reset default
Select this option and click Apply to format the installed hard disk drives and reset the
device to the default configuration. Select the Keep log file check box to save the log file
when reset.
z Backup Config file
Select this option and click Apply to save the current customized configuration of the
device as a file on your PC.
z Restore Config file
Click Browse to find the configuration file, and then click Apply to restore the customized
configuration.
NOTE
Please remember to reboot your device when you clicked Apply button.
„ Firmware
This sub-menu displays the firmware version of the device. In addition, you can upgrade the
firmware once you have a latest version of firmware. When you are upgrading the firmware,
make sure that the device is connected to the power source during the process. Otherwise, the
device might be damaged because of failure of upgrading firmware.
z Firmware file
Click Browse to find the firmware file and click Update.
4-CH Network lVideo Recorder
- 22 -
4.2.3 Storage Setup
The Storage Setup menu provides the information and controls of the installed hard disk drives,
including the USB device.
NOTE
You are not recommended to use the USB device as your major storage device.
„ Space
Click Add to configure the storage space on the installed hard disk drives: selecting Single
Disk or RAID. Then, click Apply to start making file system.
- 23 -
NVR-400 User Guide
If you have two hard disks installed in the device, you can select a disk configuration for RAID:
RAID 0
RAID 1
JBOD
(not recommended) Provide data striping.
(recommended) Provide mirroring over both disks.
(maximum data storage space) Combine both drives in a
linear fashion to create one volume.
When completed, the related information of the disks is displayed on the screen.
Click Add to add a storage space, or click Delete to remove the current storage space.
NOTE
Please remember to reboot your device when you clicked Apply button.
4-CH Network lVideo Recorder
- 24 -
„ USB Disk
If you connect an external USB disk, this sub-menu displays the information of the USB disk.
To safely remove the connected USB device, click unmount from this sub-menu. (The other
way is pressing the Unmount button on the front panel of the device for disconnecting the USB
Port 1.)
To reload the information of the connected USB devices, click refresh.
Click format to format the connected USB disk.
NOTE
Please remember to reboot your device when you clicked “apply” button.
- 25 -
NVR-400 User Guide
„ Share Folder
This sub-menu allows you to specify the shared folder of the disks. Click Add and then assign
the destination folder from the Share Folder list and give a brief instruction in the Comment
box.
The Authority option allows the administrator to limit the usage of the shared folder. Select the
authority type (Read/Write or Read Only) from the list to meet your need.
Finally, assign the storage location from the Volume list.
When completed, click Apply to add the folder that you assigned. You can then use the File
Explorer on your PC to check the folder that will be displayed as the directory under the device
name.
To change the setting, select the folder from the Share folder list and then click Edit. To
remove, select it and then click Delete.
NOTE
Please remember to reboot your device when you clicked Apply button.
„ File Management
This sub-menu displays the log of file system that you have made in the device.
4-CH Network lVideo Recorder
- 26 -
4.2.4 Authorization Setup
The Authorization Setup menu allows you to manage the users and groups of the device.
„ User
Click Add and then assign the user name in the Select User box, and give a brief instruction in
the User Description box.
If you have set up groups for organization, you can assign the user to a group from the Group
list.
Enter the password twice for the new user in the Password and Confirm Password boxes,
and then select the Permission type (Admin or User).
Specify the storage quotas for the user from the Quota option of Space Status.
When completed, click Apply to add the user. You can change the user’s setting by selecting
the user and then clicking Edit, or remove the user by selecting the user and then clicking
Delete.
NOTE
Please remember to reboot your device when you clicked Apply button.
- 27 -
NVR-400 User Guide
„ Group
Click Add and then assign the group name in the Group Name box, and then you can
add/remove users for the group from the Member option.
When completed, click Apply to add the group. To organize the users for the group, click Edit
Member. To remove the group, select it from the list and then click Delete.
„ Authorization
This sub-menu displays the assigned access rules and quotas of the users and groups.
4-CH Network lVideo Recorder
- 28 -
4.2.5 Network Service
The Network Service menu allows you to set up the network services for the device, such as FTP
server, UPnP media server, etc.
„ Windows OS
z Windows Network Setup
- Workgroup: Enter the workgroup name where the device is installed within your network.
- WINS Server: WINS (Windows Internet Name Service) server is used to support NetBIOS
over TCP/IP (NetBT). Enter the IP address of the WINS server in the box, otherwise you
cannot connect to a remote network resource by using its NetBIOS name.
- 29 -
NVR-400 User Guide
„ FTP
This sub-menu contains the options that allow you to enable/disable the FTP service of the
device.
z Start FTP Service
Select this option to enable the FTP server of the device. Once you start the FTP service,
you should assign the FTP Port (the default is port 21) .
User transmission limitation
Specify the maximum upload and download speed (KB/s) by entering the proper values in
the related boxes.
„ UPnP Media Server
The device supports UPnP (Universal Plug and Play) and port auto mapping function so that
you can access the device if it is behind an NAT router or firewall. Select this option to enable
the UPnP media server and then assign the Path from the list.
4-CH Network lVideo Recorder
- 30 -
„ iTunes Server
The device features an iTunes Server. It provides the ability to share files to the computer on
the local network running iTunes. If the function is enabled, the device will be automatically
detected in the iTunes program and the files contained in the specified directory will be
available to stream over the network.
Select this option to enable the iTune server and then assign the Path from the list. You can
also set up the Use Password to avoid unauthorized access.
„ USB Printer (only when an USB printer is connected)
When you connect an USB printer to the USB Port 2 of the device, this sub-menu displays the
information of the USB printer.
- 31 -
NVR-400 User Guide
4.2.6 NVR
The NVR menu allows you to add Internet cameras and view the live video.
„ IP Camera Backup
Click Auto Add to add the camera automatically, or click Add and to add the camera manually
through the following setup window:
4-CH Network lVideo Recorder
- 32 -
z IP
Enter the IP address of the camera.
z HTTP Port
Assign the HTTP Port for the camera (the default is 80).
z RTSP Port
Configure the transmission of streaming data within the network. The default RTSP (Real
Time Streaming Protocol) port is 554.
z User ID/Password
Enter the user name and password for accessing the camera.
z Cam Vendor
Select the manufacturer of the camera from the list.
z Split file
When the recorded file is too large, use this option to split it by selecting file size.
z Space
Specify the storage space for the camera.
z Motion Enable
Enable of disable the motion detection of the camera (if have).
z Recycle
Enable of disable the recycling function when the storage space on the device is full.
z Limit
Select Yes to limit the recording file by specifying the storage volume from the list.
Otherwise, select No to record without limitation.
When completed, click Next to set up the schedule for using the camera, and then click Apply to
add it to the list.
You can then change the configuration of the camera by selecting it from the list and then clicking
Edit. To remove a camera, select it and then click Delete.
- 33 -
NVR-400 User Guide
„ Quad View
In the Quad View screen, you can view the live video from the connected camera. You can
view up to four cameras simultaneously.
4.2.7 Schedule Download
4-CH Network lVideo Recorder
- 34 -
The Schedule Download menu allows you to set up download schedule.
Click Add and the following setup window will appear:
Please input the file name.
z Login
Select Anonymous or Account from the list according to the settings of the target server. If
you have to select Account to login, you should enter the correct User name and
Password.
z URL
Enter the URL address of target server.
z Save To
Assign the destination folder from the list to save the downloaded files.
z When
From the Date and Time setting options, set up the start-up time to download files.
z Backup
Enable the backup function of your device by selecting None, Every Day, Every Week, or
Every Month, as well as the Time.
When completed, click Apply to save this download task to the Schedule List.
You can delete the download task by selecting it from the Schedule List and then clicking Delete.
When you change the settings of selected task, click Refresh to reload the status of these tasks.
- 35 -
NVR-400 User Guide
4.2.8 Logout
The Logout menu allows you to exit or shutdown the system.
„ Logout
From this sub-menu, click Apply to exit the Web Configuration Utility and go back to the Login
window.
„ Shutdown
From this sub-menu, you can do one of the following:
z Select Shutdown Now and click Apply to turn off the device.
z Select Reboot and click Apply to reboot the device.
4-CH Network lVideo Recorder
- 36 -
4.2.9 Help
The Help menu displays the information for each setting option of the device. Click the topic
(marked as blue color) to link to the corresponding page and view the related information in detail.
- 37 -
NVR-400 User Guide
A PPENDIX
Specifications
General
OS
Embedded Linux
Ethernet
1 x RJ-45, 10/100/1000 Base-TX
USB Interface
2 x USB2.0 for backup device and printer
Storage Device
2 x 3.5” SATA hard disk
Button
Shut down button, Unmount button, Reset button
LED Display
1 x LAN, 2 x HDD, 2 x USB
HDD Configuration
Standard, RAID 0, 1 and JBOD
Video Input
4 channels IP camera
Recording Mode
Manual, Schedule
Network Service
TCP/IP, DHCP, DNS, HTTP, FTP, NTP, SMTP, UPnP
Network File Protocol
Microsoft Networks (CIFS/SMB), Internet (HTTP), FTP
Management
Web-based administration
Network Time Protocol
Multiple users account
E-mail notification
System log
Firmware upgrade
File System Type
Internal HDD support: XFS
External USB drive support: FAT32 / EXT3
User Interface
IE browser
IPFinder utility
Multiple Language
Yes
4-CH Network lVideo Recorder
- 38 -
How to fast access the recording files
1. Click Start menu > Run. Then fill the UNC of NVR. (For example: \\192.168.0.100). Enter to next.
2. Fill the username and password. (For example: admin/admin). Enter to login.
- 39 -
NVR-400 User Guide
3. After login, the share folder will be showed in the window.
The default folder name of camera is “cam-ipaddress_port”.
4. Click one of the folders to access the recording files.
The file name of recording files will be YYYY-MM-DD-hh-mm-ss.avi
TIP
We suggest using VLC player for playing the recording files if you don’t have further players which
support codec of avi format.
4-CH Network lVideo Recorder
- 40 -
5. You can find the records of recording files via Web browser.
Go to Storage Setup > File Management. It shows the entire share folders.
6. Click the link of camera for listing the records.
You can delete the recording files here only.
- 41 -
NVR-400 User Guide
EC Declaration of Conformity
For the following equipment:
*Type of Product
*Model Number
: 4-Ch Network Video Recorder
: NVR-400
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 11F, No. 96, Min Chuan Road, Hsin Tien,
Taipei, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
(89/336/EEC, 92/31/EEC, 93/68/EEC).
For the evaluation regarding the Electromagnetic Compatibility, the following standards were
applied:
EN 55022
EN 61000-3-2
EN 61000-3-3
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
(2006)
(2006)
(1995+A1: 2001 + A2: 2005)
(1998+A1: 2001+A2: 2003)
(1995 + A1: 1998 + A2: 2000)
(2006)
(2004)
(2005)
(2007)
(1993 + A1: 2000)
(2004)
Responsible for marking this declaration if the:
⌧ Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address:
11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C
Person responsible for making this declaration
Name, Surname
Position / Title :
Taiwan
Place
John Sung
Product Manager
27 Feb., 2009
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected]
http://www.planet.com.tw
11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement