Octave CD, Karaoke, DVD Copy Master User Guide

Add to My manuals
38 Pages

advertisement

Octave Copy Master CD, Karaoke & DVD Duplicators User Guide | Manualzz
Copy Master
Copyright and Trademark
Information
The product and material in this manual is subject to change
without prior notice and does not represent a commitment on
the part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
All brand names and trademarks are properties of their
respective owners.
This manual contains materials protected under International
Copyright Laws. All rights reserved. No part of this manual
may be reproduced, transmitted or transcribed without the
expressed written permission of Octave Systems Inc.
The Copy Master is to be used in a lawful manner. Violation of
the International Copyright Laws is a criminal charge.
Octave Systems Inc. is not responsible for the illegal actions of
users, nor consequential damage in connection with the
furnishing, performance, or use of the equipment described
herein.
504A Vandell Way, Campbell, CA 95008 – USA
Tel: 408-866-8424 ● Fax: 408 866 4252
www.octave.com ● [email protected]
Mar 8, 2005
1
Octave Systems, Inc.
Table of Contents
Chapter One: Introduction......................................... 5
1.1 Note About this Manual........................................... 5
1.2 Overview.................................................................. 5
1.3 Features.................................................................... 5
1.4 Specifications........................................................... 6
1.4.1 CD Copy Master ................................................. 6
1.4.2 DVD Copy Master .............................................. 8
Chapter Two: Menu & Functions ............................ 10
2.1 CD Menu Flowchart .............................................. 10
2.2 DVD Menu Flowchart ........................................... 11
2.3 LCD Panel ............................................................. 13
2.4 Changing DVD into 3, 5 or 8 Recorder System .... 14
Chapter Three: Function Details ............................. 16
1 Copy.......................................................................... 16
2 Test ........................................................................... 17
3 Test & Copy.............................................................. 18
4 Verify........................................................................ 18
5 Compare.................................................................... 19
6 Prescan...................................................................... 20
7 Disc Info ................................................................... 21
8 Select Source ............................................................ 22
9 Image ........................................................................ 23
9-01 Load ................................................................... 23
9-02 Delete Image...................................................... 24
9-03 Image Info.......................................................... 25
9-04 Compare Image.................................................. 25
9-05 Select Image ...................................................... 27
9-06 Image SRC Drive............................................... 28
9-07 Image Format Info ............................................. 28
10 Edit Track (for CD & Karaoke only)...................... 29
10-01 CD to CD Edit (Compilation).......................... 29
10-02 CD to HDD (Works only when a hard disk is
connected) .................................................................. 33
10-03 Play Audio Track............................................. 38
2
Copy Master
10-04 Close Session ................................................... 38
11 Setup - DVD ........................................................... 39
11-01 Language - DVD.............................................. 39
11-03 DVD Burn Speed - DVD ................................. 40
11-04 Read Speed - DVD .......................................... 41
11-05 Auto Start Drive - DVD................................... 41
11-06 Start-up Menu - DVD ...................................... 42
11-07 Auto Verify - DVD .......................................... 42
11-08 Auto Compare - DVD...................................... 43
11-09 Auto Prescan - DVD ........................................ 43
11-10 Eject Disc - DVD............................................. 44
11-11 Burn on the Fly - DVD .................................... 45
11-12 Burn Mode - DVD ........................................... 46
11-13 Display Time – DVD....................................... 46
11-14 Button Sound - DVD ....................................... 47
11-15 Device Info - DVD .......................................... 47
11-16 System Info - DVD .......................................... 49
11-17 Quick Erase - DVD.......................................... 49
11-18 Full Erase - DVD ............................................. 50
11-19 Auto Close Tray - DVD................................... 51
11 Setup - CD .............................................................. 51
11-01 Language - CD................................................. 52
11-03 Read Speed - CD ............................................. 53
11-05 Start-up Menu - CD ......................................... 54
11-06 Auto Verify - CD ............................................. 54
11-07 Auto Compare - CD......................................... 55
11-08 Auto Prescan - CD ........................................... 55
11-09 Eject Disc - CD ................................................ 56
11-10 Burn on the Fly - CD ....................................... 57
11-11 Burn Mode - CD .............................................. 57
11-12 Button Sound - CD .......................................... 58
11-13 Device Info - CD.............................................. 58
11-14 System Info - CD ............................................. 60
11-15 Quick Erase - CD............................................. 61
11-16 Full Erase - CD ................................................ 61
12 Advanced Setup ...................................................... 62
3
Octave Systems, Inc.
Copy Master
12-01 Under Run Protect ........................................... 62
12-02 Overburn.......................................................... 63
12-03 Read Error Skip ............................................... 63
12-04 Format Hard Disk ............................................ 64
12.5 Verify HDD ....................................................... 64
12-06 Burn-in............................................................. 65
12-07 Update Firmware ............................................. 66
12-08 Compare Firmware .......................................... 67
12-09 H/W Diagnostics.............................................. 67
12-10 Load Default .................................................... 68
12-11 CD+G (for Karaoke)........................................ 69
12-12
ISRC & MCN ............................................ 69
12-13 Switch USB Mode (not available).................. 69
12-13
CD Text...................................................... 69
12-15 Multisession DVD ........................................... 70
Chapter Four: Trouble Shooting & Tech Support. 71
DVD Dual Formats - + Information ........................ 73
Chapter One: Introduction
1.1 Note About this Manual
This manual covers the one, four, and seven drive CD and
Karaoke, plus the three, five and eight drive for the DVD Copy
Master. In most cases the operation is identical between each of
the units.
The CD Copy Master 1-1, DVD Copy Master 1-1, and the
Karaoke Copy Master 1-1 DOES NOT come with a Hard
Drive. Any section of this document that mentions a hard drive
is not applicable.
1.2 Overview
The Copy Master is a CD and DVD standalone duplicator and
does not need to connect to a computer to perform tasks. It
provides flawless operation in duplicating with high accuracy.
With its professional mechanical design and multifunction LCD
panel, the Copy Master is easy for any end-user to operate. It is
a perfect cost effective duplicator for audio, data, video, etc.
applications. Four simple push buttons in a panel have been
designed to provide copy mode selections and copy operation.
1.3 Features
4
• Standalone IDE CD ROM to IDE CD recorder copy
controller or DVD Source Drive to DVD recorder
• System diagnostics performed when power is switched on
• Has a 160Gb hard drive for storing up to 148 CD images
5
Copy Master
Octave Systems, Inc.
•
•
•
•
or 30 DVD images (Works only when a hard disk is connected)
Auto format detection
User friendly interface with an easy to read LCD display
Fast copy support for high speed CD-RW writing mode
Easy operation - no software and training required
Length:
Width:
Height:
CD Format -
CD-ROM (Mode 1 & Mode 2), CDROM XA (Mode 2 form 1 & form 2),
CD-DA, Mixed-Mode, video CD, CDI, Photo CD (Singe & Multi-Session),
CD-Extra, HFS, CD-Bridge, ISO 9660,
CD-R, and CD-RW
Writing Mode -
Auto Detect (DAO - Disk at Once,
TAO - Track at Once)
CD-ROM Drive -
52X
1.4 Specifications
1.4.1 CD Copy Master
Power requirement - Voltage: 110-240V AC
Current: 50/60Hz 300Watt (4 & 7 CDR
drive models)
Current 50/60Hz 100 Watt (Single
CDR drive model)
Environment -
Temperature
Operating 0 °C to 70 °C
Storage -20 °C to 85 °C
Interface: IDE/ATAPI
Read Speed: 52X
Data Transfer Rate: 6MBps
Access Time: 85ms
Buffer Size: 2MB
Features: Built-in headphone jack,
volume control and power eject
Disc Loading: Power tray
Humidity 15% to 90%
Packaged Shipping Weights
Model 7 Drive 50 lbs (22.6 kg)
Model 4 Drive 45 lbs (20.4 kg)
Model 1 Drive 15 lbs (6.8 kg)
Model both 4 & 7 CDR drive models
Length:
Width:
Height:
Model Single drive model
.
6
CD-RW Drive 25 inches (63.5 cm)
25 inches (63.5 cm)
15 inches (38.1 cm)
6.5" (16.5cm)
11.2" (28.5cm)
7.4" (19.Ocm)
52X
Interface: IDE/ATAPI
Access Time: 80ms (1/3 stroke)
Capacity: 700MB (Data), 80Min.
(Audio) Transfer Rate: Write: 52X (6.0
MBps), Rewrite: l OX (1.5MBps);
Read: 52X (6.OMBps)
Controller Buffer: 8 MB
Buffer Management: Buffer under-run
prevention
7
Copy Master
Octave Systems, Inc.
Formats: Single session, multi-session,
and incremental
Features: Built-in headphone jack, dual
status LED's, volume control and
power eject
Disc Loading: Power tray
Audio Line Outputs
CD-ROM has an RCA type stereo line
output jack for connecting to powered
speakers.
Warranty -
One Year: Parts and Labor
Auto Interface
Analog Audio Output
Write Speed
DVD-R
DVD – RW
DVD + R
DVD + RW
DVD+R DL*2
CD – R
CD – RW
16x, 12x, 8x, 6x, 4x, 2x, 1x
4x*4, 2x, 1x
16x, 12x, 8x, 6x, 4x. 2.4x
4x, 2.4x
4x, 2.4x
32x, 24x , 16x, 10x, 4x
24x, 20x, 16x, 10x, 4x
Packaged Shipping Weights
Model 8 Drive
Model 5 Drive
Model 3 Drive
Model 1 Drive
50 lbs (22.6 kg)
45 lbs (20.4 kg)
26 lbs (11.8 kg)
15 lbs (6.8 kg)
Model both 4 & 7 DVD drive models
Length:
Width:
Height:
25 inches (63.5 cm)
25 inches (63.5 cm)
15 inches (38.1 cm)
Model 3 drive DVD model
Length:
Width:
Height:
22 inches (55.8 cm)
14 inches (35.56 cm)
12 inches (30.48 cm)
Model Single drive model
Length:
Width:
Height:
6.5" (16.5cm)
11.2" (28.5cm)
7.4" (19 cm)
1.4.2 DVD Copy Master
Pioneer A08 Specifications Write Support
DVD
DVD-R 4.7GB, DVD-RW, DVD+R,
DVD+RW
CD
CD-R 700 (type 80), 650MB (type 74),
CD-RW, Highspeed CD-RW,
Ultraspeed CD-RW
Read Support
DVD
DVD-ROM, DVD-VIDEO (Single &
Dual layer), DVD-R, DVD-RW,
DVD+R, DVD+RW & DVD-RAM
CD
CD-ROM(Mode1&2), CD-ROM XA,
CD-DA (CD Audio), Video CD,
PhotoCD (single/multi-session), CD
EXTRA, CD-Text, CD-R, CD-RW
Interface
ATAPI Interface
ATA/ATAPI-5
IDE Data Transfer Mode
PIO Mode 4, Multi Word DMA
Mode 2, Ultra DMA Mode 4 (Ultra
DMA 66)
8
Warranty
One Year: Parts and Labor
9
Octave Systems, Inc.
Copy Master
Chapter Two: Menu & Functions
2.1 CD Menu Flowchart
1
2
3
4
5
6
7
8
9
Copy
Test
Test & Copy
Verify
Compare
Prescan
Disc Info
Select Source
Image (Works only when a hard disk is connected)
9 - 01 Load
9 - 02 Delete Image
9 - 03 Image Info
9 - 04 Compare Image
9 - 05 Select Image (Size of each partition is 1GB on CD & 5 GB on DVD)
9 - 06 Image SRC Drive (Select which drive to load image)
10
Edit Track (For AUDIO disc & CD+G only)
10 - 01 CD to CD Edit
10 - 02 CD to HDD Edit (Works only when a hard disk is connected)
10 - 03 Play Audio Track
10 - 04 Close Session
11
Setup
11 - 01 Language (Type 1: English - Type 2: Spanish)
11 - 02 CD Burn Speed
11 - 03 Read Speed (Maximum)
11 - 04 Auto Start Drive
11 - 05 Startup Menu
11 - 06 Auto Verify (On Off)
11 - 07 Auto Compare (On Off)
11 - 08 Auto Prescan (On Off)
11 - 09 Eject Disc
11 - 10 Burn On The Fly (On Off)
11 - 11 Burn Mode (1. DAO 2. TAO)
11 - 12 Button Sound (On Off)
11 - 13 Device Info
11 - 14 System Info
11 - 15 Quick Erase
11 - 16 Full Erase
12
12
12
12
12
12
12
-
12
12
12
12
12
12
12
-
Adv Setup (Press ESC 2 seconds to enter this menu)
01 Under-run Protect (On Off)
02 Over-burn (On Off)
03 Read Error Skip (On Off)
04 Format HDD (Works only when a hard disk is connected)
05 Verify HDD (Works only when a hard disk is connected)
06 Burn-in
12-06-1 Erase & Copy
12-06-2 Test
07 Update Firmware
08 Compare Firmware
09 H/W Diagnostic
10 Switch USB Mode (N/A)
11 Load Defaul (Restore System Default Configuration)
12 CD+G (Karaoke Model Only)
13 ISRC & MCN (N/A)
10
2.2 DVD Menu Flowchart
1.
2.
3.
4.
5.
6.
7.
8.
9.
Copy
Test
Test & Copy
Verify
Compare
Prescan
Disc Info
Select Source
Image (Works only when a hard disk is connected)
9.01
Load (If there is an image currently on the partition,
the system will ask if you would like to overwrite it or select another partition)
9.02
Delete Image
9.03
Image Info
9.04
Compare Image
9.05
Select Image (Size of each partition is 1GB on & 5 GB on DVD)
9.06
Image SRC Drive (Select which drive to load image)
9.07
Image Format Info
10. Edit Track (For AUDIO & Karaoke only)
10.01 CD to CD Edit
10.02 CD to HDD Edit (Works only when a hard disk is connected)
10.03 Play Audio Track
10.04 Close Session
11. Setup
11.01 Language (1: English 2: Spanish)
11.02 CD Burn Speed (If no disc is in CD-RW, list all supported speeds
or list speed supported by disc)
11.03 DVD Burn Speed (Maximum)
11.04 Read Speed (Maximum)
11.05 Auto Start Drive (Off)
11.06 Startup Menu (1. Copy)
11.07 Auto Verify (Off)
11.08 Auto Compare (Off)
11.09 Auto Prescan (Off)
11.10 Eject Disc (1. Eject Good Only)
11.11 Burn On The Fly (On)
11.12 Burn Mode (1. DAO)
11.13 Display Time (On)
11.14 Button Sound (On)
11.15 Device Info
11.16 System Info
11.17 Quick Erase
11.18 Full Erase
11.19 Auto Close Tray
12. Adv Setup (Press ESC 2 seconds to enter this menu)
12.01 Under-run Protect (On)
12.02 Over-burn (Off)
12.03 Read Error Skip (Off)
12.04 Format HDD (Works only when a hard disk is connected)
12.05 Verify HDD (Works only when a hard disk is connected)
11
Octave Systems, Inc.
12.06
12.07
12.08
12.09
12.10
12.11
12.12
12.13
12.14
12.15
Copy Master
Burn-in
Update Firmware
Compare Firmware
H/W Diagnostic
Load Default (Restore System default configuration)
CD+G (Karaoke Model Only)
ISRC & MCN (N/A)
Switch USB Mode (N/A)
CD Text (On)
Multisession DVD
2.3 LCD Panel
1.
LCD Display Panel: Displays menus, functions
and messages.
2.
Scroll up through menus or functions.
3.
Scroll down through menus or functions.
4.
Execute the function which you have selected.
5.
Cancel the function which you have selected,
or press two times to get out of the function and
back to the menu.
When the system is powered on, the Copy Master checks the
hardware installation, and will process a self-test for several
seconds. After the self-test procedure, the LCD will stop at:
1. Copy
12
13
Copy Master
Octave Systems, Inc.
2.4 Changing DVD into 3, 5 or 8 Recorder
System
Place the master disc in the Source Drive. This is the default
Source. (8 Select Source would display “SRC: DVDDUAL
00 IDEO Master”).
Press the down arrow to 9 Image. Press ENT. The LCD
shows “9-01 Image P:A Load”. This indicates the
duplicator is ready to copy an image into partition A of the
Hard Drive. Press ENT.
The LCD will display the load progress and finish with
“Image Load OK”.
Next the Source for the duplication has to be changed from
the Source Drive to the Hard Drive. Press ESC 2 times and
the up arrow to 8 Select Source and press ENT. Press the
down arrow to “Src: HDD 01 IDEO Slave” and press ENT.
The LCD shows “HDD selected”.
Press ESC 2 times and the up arrow to “1. Copy P:A”.
Take out the master disc from the Source Drive and place a
blank disc into it and all the writers.
Once all the writers have detected the discs (green LED off)
press ENT to start copying.
When the Copy process has completed, those discs that have
passed will be ejected automatically. Failed discs will remain
in their respective writers.
14
15
Octave Systems, Inc.
Copy Master
Chapter Three: Function Details
2 Test
1 Copy
This function will simulate an actual recording only to -R or
–RW discs. +R discs cannot be tested. When the testing
process has completed, the discs will remain blank.
This function will record data from the CD ROM or Source
Drive to the blank disc(s) in the writers. The default source is
the CD ROM or Source Drive.
2. Test
Press ENT to start the disc simulation of
copy or press ESC to exit.
Erasing Disc
For discs that contain data, simulation
will perform a quick erase of all old data
before emulation. Never perform an
"Emulate" on –R/RW discs that contain
important data.
Testing – 52X 0%
650.0 MB 74:00
The LCD will display information
regarding the progress of testing.
2. Test
OK: 04
When the process has finished, the LCD
will display the result.
1. Copy
Copying- Max 1%
650.0 MB 74:00
1. Copy
0K: 04
Place master in the Rom or Source drive,
and blank disc in one or more writers.
When all writers detect the disc(s), press
ENT and the duplicator will start
copying.
The LCD will display information
regarding the copying process.
When the process has completed, those
discs that have passed will be ejected
automatically and the failed discs will
remain in the writers.
CD/DVD-RW (erasable) discs containing data can also be
copied by the duplicator. If the duplicator detects that data is
stored on the CD/DVD RW discs, it will perform a quick erase
automatically before copying new data. No special setting or
procedure is required to erase the old data.
16
Terminating halfway through the "simulate" process will not
affect the CD/DVD-R disc and they will remain blank.
However, note that CD/DVD-RW discs containing data may be
destroyed and cannot be retrieved again. Some CD/DVD writers
may not support sudden termination during operation. The
duplicator may hang and it can only be reset by turning off the
power.
17
Copy Master
Octave Systems, Inc.
3 Test & Copy
3. Test & Copy
Testing-52X 0%
650.0MB 74:00
Verify--52X
0%
650.0MB
74:00
The LCD will display the progress.
4. Verify
OK: 03
The LCD will display the result.
Press ENT to start the simulation to
copy and after the actual recording to the
disc(s) will start.
Before the copying process begins, the
writers will simulate writing data to the
disc(s).
5 Compare
Copying-52X 0%
650.0 MB 74:00
3. Test & Copy
OK: 04
When the testing process has completed,
the duplicator will start the actual
recording process onto the disc(s).
This function will compare the data between the master and
target discs after the discs have been copied. Audio and Video
discs cannot be compared.
5. Compare
Press ENT to start the function or press
ESC to exit.
Compare--XX
0%
650.0MB
74:00
The LCD will display the progress.
Compare
Fail: 0
When the process has completed, the
LCD will display the results. The disc(s)
will be ejected.
When the process has completed, the
LCD will display the results.
4 Verify
This function will ensure that data discs that have just been
copied can be read correctly in the CD ROM or Source Drive.
Audio and Video discs cannot be verified.
4. Verify
OK:3
Diff: 0
Press ENT to start the disc or press
ESC to exit.
18
19
Copy Master
Octave Systems, Inc.
Src: 01
Total:
CD-ROM
650.0MB
Press the ENT button to view details.
Prescan
Src: 02
Identical
CD-RW
The LCD will display the results are
identical.
Prescan Fail!
Compare
Fail: 1
OK: 2
Diff: 0
If the results have failed, the LCD will
display the number of discs that have
failed and succeeded.
OK!
If the master disc can read correctly, the
LCD will display an “OK!” message.
If the master disc cannot read correctly,
the LCD will display a “Fail!” message.
7 Disc Info
This function will display the total amount of data information
on the master disc.
Press ENT to display the disc
information.
7. Disc Info
6 Prescan
This function will scan the master disc to see if it can be read
correctly and test the read speed.
6. Prescan
Press ENT to prescan the disc or press
ESC to exit.
Scanning--52X
0%
650.0MB
74:00
The LCD will display the progress.
20
Total
Total
02
10
Total: 74:00
Total: 650MB
Sessions
Tracks
The LCD will display the total amount of
sessions and tracks on the master disc.
Press ENT again and the LCD will
display the total time and capacity on the
master disc.
21
Octave Systems, Inc.
Copy Master
Session 01
Track 01-09
Press ENT again and use the arrow
button to select the session. The LCD
will display what information is
contained on the session.
Track 01
AUDIO 03:54
Press ENT again and use the arrow
button to select the track. The LCD will
display what information is contained on
the track.
that contains no data. Select the partition with data (9-05 Select
Image) or use the Image function (9. Image) to load the master
data to the current partition.
9 Image
8 Select Source
This function allows the user to set the source to the CD ROM
or Source Drive, or the Writers or HDD (Image). The default
source is the CD ROM or Source Drive (top drive). Only the
ROM can be selected for 1-1 Copy Master.
Works only when a hard disk is connected
This function describes how to copy a CD/DVD “Image” to the
hard drive. For high quantity duplication, loading the image to
the hard drive is the preferred method instead of continually
reading from the CD ROM or Source Drive, which may be
subject to miss-reads.
9-01 Load
Place the master disc into the CD ROM or Source Drive or any
one of the writers that has been selected as the source drive.
Press ENT to select the source drive.
9-01. Image
Load
Use the arrow button to select the CD
ROM (see diagram) or
Source Drive (Src: ….00 IDEO Master)
or
HDD (Image) (Src: HDD..01 IDEO
Slave)
Load- A - 52X
0%
650.0MB
74:00
The LCD will display the progress
Src: CD-ROM
01 IDEO Slave
CD-ROM selected!
When the source drive has been selected,
press ENT. The LCD will display the
source information.
Image load OK
The LCD will display when the image is
successfully loaded.
The duplicator will prompt you with an error message when you
select the hard drive as a source and try to copy from a partition
22
P: A
Press ENT to load the data into the
current partition of the hard drive.
P: A is Partition A.
8. Select Source
23
Octave Systems, Inc.
Image exists
Overwrite? Yes
Copy Master
If there is an image already in the
partition, the system will ask if you
would like to overwrite it. Use the arrow
button to select “Yes” or “No” then press
ENT.
9-03 Image Info
This function will display the total sessions and tracks in the
current partition on the hard drive.
9-03. Image
Image Info
The Source for duplication has to be changed from the Source
Drive to the hard drive. Press ESC 2 times and then the up
arrow to "8. Select Source" and press ENT. Press the down
arrow to (Src: HDD..01 IDEO Slave) then press ENT. The
LCD shows "HDD selected”. You are now ready to copy from
the Image/Hard Drive.
Total
Total
01
01
P: A
Sessions
Tracks
Press ENT to display the disc
information or press ESC to exit.
The LCD will display the total amount of
sessions and tracks on the hard drive
partition.
9-02 Delete Image
This function clears the master data stored in the current
partition of the hard drive.
9-02. Image P: A
Delete Image
Delete Image in
Partition A? Yes
Partition A:
Image is deleted
Total: 74:00
Total 650 MB
Press ENT again and the LCD will
display the total time and capacity on the
hard drive partition.
Session 01
Track 01 - 01
Press ENT again and use the arrow
button to select the session. The LCD
will display what information is
contained in the session.
When the current partition on the hard
drive contains an image, you can use this
function to delete it. Press ENT.
The system will ask for a confirmation to
make certain that you would like the
image in the partition deleted. Use the
arrow button to select “Yes” or “No”
then press ENT.
Track 01
DATA 650.0MB
Press ENT again and use the arrow
button to select the track. The LCD will
display what information is contained in
the track.
The LCD will display the image is
deleted.
9-04 Compare Image
This function will compare the image between the disc source
and the current working partition on the hard drive. Audio and
Video discs cannot be compared.
24
25
Octave Systems, Inc.
Copy Master
Src: 01
Total:
Press ENT to view the details
CD-ROM
0 Bytes
Press ENT to start or press ESC to exit.
9-04. Image P: A
Compare Image
If the compare results have failed, the
LCD will display the reason for the
failure as shown to the left.
Src: 02
CD-RW
TOC not match
Compare-A-XX
0%
650.0MB
74:00
The LCD will display the progress
Compare
Fail: 0
When the process has completed, the
LCD will display the results. The
disc(s) will be ejected.
9-05 Select Image
OK: 1
Diff: 0
This function is to select a partition on the hard drive.
9-05. Image P: A
Select Image
Src: 01
Total:
Press ENT to start or press ESC to exit.
Press ENT to view details.
CD-ROM
650.0MB
The hard drive (120GB) installed in a CD system is divided up
into 1GB partitions and can hold 110 images.
Tgt: 00
P: A
Identical
Compare
Fail: 1
The LCD will display the results are
identical.
HDD
If the results have failed, a message will
display the number of discs that have
failed and succeeded.
OK: 0
Diff: 0
26
The hard drive (120GB) in a DVD system is divided up into
5GB partitions and can hold 22 images.
Select Working
Partition A
Use the down arrow button to select
which partition will be set (partitions are
in alphabetical order). When partition is
selected press ENT. The LCD will
display the partition letter.
27
Octave Systems, Inc.
Set Partition to
A
Copy Master
Press ESC to get out of this function and
then the up arrow to 9-01 Load. Press
ENT. To copy from this partition go to
8. Select Source for the HDD which will
show this partition and then to 1.Copy
P:A.
It is advisable to keep a log on information for each
partition.
9-07. Image P: A
Image Format Info
Press ESC and arrow to enter.
Image Format Info
DVD
Press ENT to see the format information.
HD00 not Formt!
Format HDD? Yes
If your hard disk is not formatted the
LCD will display this.
HD Partition
Format Select? DVD
When the LCD displays the image press
ENT to confirm Yes.
9-06 Image SRC Drive
This function selects the source of the data to be written to the
hard drive. The default source is the CD ROM or Source
Drive.
9-06. Image P: A
Image SRC Drive
Press ENT to select the source drive.
Select Img Src:
01 IDE0 CD-ROM
Use the arrow button to select the CD
ROM (see diagram) or
Source Drive (Src: ….00 IDEO Master)
or
HDD (Image) (Src: HDD..01 IDEO
Slave)
Load image from
Drive ID-01
When the source has been selected, press
ENT. The LCD will display the source
information.
10 Edit Track (for CD & Karaoke only)
This function can combine tracks from different CD discs onto
one single CD disc. For example, you can make a collection of
favorite songs from different music CDs or Karaoke CDs and
store them onto one disc. This function does not apply to
DVD and Data.
9-07 Image Format Info
10-01 CD to CD Edit (Compilation)
This function shows how the Hard Drive (Image) is formatted.
This function will let you select the track or tracks from the CDROM or Source Drive.
28
29
Copy Master
Octave Systems, Inc.
10-01. Edit Track
CD to CD Edit
Select Track:
1/10 03:25
Select Track
+1/10 03:25
Select Track
END 4Trk 15:25
END edit disc
and burn? Yes
Copying- 52X Edit
1/10
1/1
Press ENT.
Burn Complete!
OK: 03
When the process has finished, the LCD
will display a “Burn Complete!”
message. Press ENT.
Follow the LCD display to select the
track that you would like to edit.
Continue edit
next Disc? Yes
The system will ask if you would like to
continue editing. Select “Yes” or “No”
by pressing the down arrow.
Press ENT to select the track. After the
track has been selected, the “+” will
appear. Press ENT again and it will
cancel the track that you have selected to
edit. Press the down arrow to select
tracks.
Insert next disc
Finally, when the track selection has
been made, use the down arrow button to
the end of the setup screen. Press ENT
to finish the disc selection.
Use the arrow button to select “Yes” or
“No”. Then press ENT.
The LCD will show the progress.
30
If “Yes” has been selected, press ENT
and the source disc will be ejected.
Insert another audio disc to edit. It will
take a few seconds before the following
function appears.
Select Track:
+2/10 04:25
Follow the steps to select the track you
would like to edit. Then press ENT to
add it to the disc.
Select Track:
END 6Trk 22:50
Finally, when the track selection has
been made, use the down arrow button to
the end of the setup screen.
END edit disc
and burn? Yes
Press ENT to finish the disc edition. Use
the arrow button to select “Yes” or “No”.
Copying- 52X Edit
1/10
2/2
The LCD will show the progress.
31
Copy Master
Octave Systems, Inc.
Burn Complete!
OK: 01
When the process has finished, the LCD
will display a “Burn Complete!”
message. Press ENT.
Select Track
End 12Trk 46:10
When the track selections have been
cancelled use the down arrow button to
the end of the setup screen. Press ENT.
Continue edit
next Disc? No
The system will ask if you would like to
continue editing. When finished, select
“No” by pressing the down arrow.
End edit disc
and burn? Yes
Use the arrow button to select "Yes".
The press ENT.
The LCD will show the progress.
Close all disc’s
sessions? Yes
The system will ask if you would like to
close the disc session. Using the arrow
button, select “Yes” and press ENT.
Burn Complete!
OK: 01
When the process has finished the LCD
will display a “Burn Complete!”. Press
ENT.
Closing Session
Please wait---
The LCD will display the progress. The
disc will eject when completed.
Continue edit
Next Disc? No
Select ‘No”.
Target Overflow
Re-select
There are too many tracks selected that
are over the total time (80 min:) or
capacity (700mb). Press ENT.
Close all disc’s
Sessions? Yes
Press ENT
Select Track:
+1/10
Press ENT to cancel some of the track/s.
Closing Session
Please wait---
The LCD will display the progress. The
disc will eject when completed.
10-02 CD to HDD
(Works only when a hard disk is connected)
This function will let you select the track or tracks from the
Source Drive to the Hard Drive.
32
33
Octave Systems, Inc.
Copy Master
Press ENT to enter the selection. Press
ESC to bring you to the next selection.
10-02. Edit Track
CD to HDD Edit
Follow the LCD to select the track you
would like to edit.
Select Track
1/10 03:25
Press ENT to select the track. After the
track has been selected, the “+” will
appear. Press ENT again and it will
cancel the track that you have selected to
edit. Press the down arrow to select
tracks.
Select Track
+1/10 03:25
Finally, when the track selection has
been made, use the down arrow button to
the end of the setup screen.
Select Track:
END 1Trk 03:25
Press ENT to finish the disc edit and
select “Yes” or “No”.
END edit disc
and burn? Yes
Load- PO- 52X
1/10
1/1
Edit
The source will be loaded onto the hard
drive. The LCD will display the progress
34
Image load OK
When the Image Load has completed,
press ENT.
Continue edit
next disc? Yes
The system will ask if you would like to
continue editing. Use the arrow button to
select “Yes” or “No”. ENT
Insert next disc
If “Yes” has been selected, the source
disc will be ejected. Insert another audio
disc to edit. It will take a few seconds
before the following function appears.
Select Track:
+2/10 04:25
Follow the steps to select the track you
would like to edit. Then, press ENT to
add it to the disc.
Select Track
END 2Trk 07:50
When the track selection has been made,
use the arrow button to the end of the
setup screen.
END edit disc
and burn? Yes
Press ENT to finish the disc edition and
select “Yes” or “No”.
35
Copy Master
Octave Systems, Inc.
The source will be loaded onto the hard
drive. The LCD will display the
progress.
Burn or Move to
partition? Move
If you select “Move”, this will move the
data from the hard drive template to the
partition.
Image load OK
When the Image Load process has
completed, press ENT.
Select Partition
A
Use the arrow to select the partition that
the data will move to.
Continue edit
next disc? OK
The system will ask if you would like to
continue editing. Use the arrow button to
select “Yes” or “No”. Select “No” and
press ENT.
Moving to P: A
0%
The LCD will display the progress of the
data that is moving.
Burn or move to
partition? Burn
The system will ask if you would like to
burn to CD or move to the partition.
Select “Burn” and it will start to record
audio from the hard drive to the CD.
Moving to P: A
OK!
When the moving of data has completed,
the LCD will show the “OK!” message.
Copy- P0- 52X 0%
1/2 Trk 03:25
The LCD will display the progress of
copying from the hard drive to the CD.
Image Exists
Overwrite? Yes
If there is an image currently on the
partition, the system will ask if you
would like to overwrite it. Use the arrow
button to select “Yes” or “No”.
Burn Complete!
OK: 03
When the burning has completed, the
LCD will show the “Burn Complete!”
message.
Moving to P: A
0%
The LCD will display the progress of the
data that is moving.
Moving to P: A
OK!
When the moving of data has completed,
the LCD will show the “OK!” message.
Press ESC twice to exit.
Load- PO- 52X
1/10
2/2
Edit
36
37
Octave Systems, Inc.
Copy Master
10-04. Edit Track
Close Session
Press ENT to enter the setting. Use the
ESC button to bring you to the next
setting.
Close all disc’s
session? Yes
The system will ask for a confirmation to
close the disc’s session. After this step,
you will not be able to write more data to
this CD.
Closing Session
Please wait---
The LCD will display information
regarding the closing process.
Closing Complete
OK: 3 Fail: 0
When the process has completed, the
LCD will display the number of discs
that are “OK” and “Fail”.
10-03 Play Audio Track
This function will turn the CD Copy Master into a music player.
The user can plug powered speakers into the audio-out jacks on
the rear of the case. The audio disc should be in the ROM or
Source drive. The source (8. Source) should be selected to the
ROM or Source drive.
10-03. Edit Track
Play Audio Track
Press ENT.
Select Track:
1/10 03:25
Use the arrow button to select which
track you are going to play. Press ENT
to start playing the track.
Playing Track-1
00:00 / 03:25
The LCD will display the information of
the track you are playing.
11 Setup - DVD
This function contains a list of options, which allows the user to
change the original default settings. However, we suggest using
the original default settings for optimal operation.
10-04 Close Session
This function will close the disc and you will not be able to
write any more data to it. It will allow your disc to be read on a
normal player.
38
11-01 Language - DVD
This option will set the language preference that will be
displayed on the LCD. Only English and Spanish are currently
supported. Other languages will be added in the future.
39
Octave Systems, Inc.
11-01 Setup
Language
Language
English
Language
Spanish
Copy Master
Press ENT.
writers. It automatically switches to the speed for which the media
is optimized.
11-03. Setup
Burn Speed
Press ENT.
DVD Burn Speed
Maximum
Press ESC twice to get out of this menu.
Press ENT or down arrow
Press ENT or ESC to exit
(not all systems are set up with Spanish).
11-04 Read Speed - DVD
11-02 CD Burn Speed - DVD
This function will set the reading speed of the source which is
the CDROM or the Source Drive. The default is maximum.
This function controls the maximum writing speed of the writers.
The standard setting is Max which will use the highest writing
speed of the writers.
11-04. Setup
Read Speed
Press ENT and ESC to exit.
Read Speed
Maximum
Use the down arrow button to change the
read speed, then press ENT.
11-02. Setup
Burn Speed
Burn Speed MAX
Press ENT.
Use the down arrow button to change the
burn speed, then press ENT.
11-05 Auto Start Drive - DVD
11-03 DVD Burn Speed - DVD
This function is set to maximum writing speed of the DVD
40
This setting controls the writers that will auto start the copy or
test function when a blank disc is inserted into the writer drive.
The default setting is Off.
41
Copy Master
Octave Systems, Inc.
11-05. Setup
Auto Start Drive
Auto Start Drive
Off
Press ENT and ESC to exit.
Use the arrow button to change the
number or the Off setting, then press
ESC to go back to the setup screen (1104).
11-07. Setup
Auto Verify
Press ENT.
Auto Verify
Off
Use the arrow button to change the On or
Off setting, then press ENT or press
ESC to go back to the setup screen (1106).
11-06 Start-up Menu - DVD
11-08 Auto Compare - DVD
This function allows the user to select one of the menu items
which will become the first menu item to show when the
duplicator is turned on. The default is 1. Copy.
This function controls the OnOff of the Auto Compare (the data
between master and target discs after discs are copied). The
default setting is Off.
11-06. Setup
Start-up Menu
Press ENT and ESC to exit.
Start-up Menu
1. Copy
Use the arrow button to select an item to
be the first menu seen when the
duplicator is turned on (1-11), then press
ENT.
11-07 Auto Verify - DVD
11-08. Setup
Auto Compare
Press ENT.
Auto Compare
Off
Use the arrow button to change the “On”
or “Off” setting then press ENT or press
ESC to go back to the setup screen (1107).
11-09 Auto Prescan - DVD
This controls the On/Off of the Auto Verify (this checks the
target discs if they can be read correctly in the CD-ROM or
Source Drive after copying). The default setting is Off.
42
This function controls the On and Off of the Auto Prescan (this
verifies that the master of the disc can be read correctly and test
the reading speed). Default setting is Off.
43
Copy Master
Octave Systems, Inc.
11-09. Setup
Auto Prescan
Press ENT..
Eject Disc
Eject All Discs
Use the arrow button to select Eject All
Discs, then press ENT or press ESC to
go back to the setup screen (11-09).
Auto Prescan
Off
Use the arrow button to change the On or
Off setting, then press ENT or press
ESC to go back to the setup screen (1108).
Eject Discs
Do Not Eject
Use the arrow button to select Do Not
Eject, then press ENT or press ESC to
go back to the setup screen (11-09).
11-10 Eject Disc - DVD
11-11 Burn on the Fly - DVD
This function controls the ejection of discs by the CD/DVD writer.
Three options are available: The Eject Good Only setting will only
eject the passed discs automatically and leave the failed ones in the
writers. The Eject All Discs will have all the writers eject the
discs no matter whether the operation is successful or a failure.
The Do Not Eject option will have all discs remain in the writers
when the job is completed and you will have to eject discs from
the writers manually. The default is Eject Good Only.
This function controls the writing methods to the CD/DVD disc.
When the setting is On, the data will perform a direct copy from
the source drive to the target drives. When the setting is Off,
the data will load into a particular temporary partition on the
hard drive. Afterward, the data to be copied will come from the
source partition. The default is ON.
11-10. Setup
Eject Disc
Eject Disc
Eject Good Only
Press ENT.
Use the arrow button to select Eject
Good Only, then press ENT or press
ESC to go back to the setup screen (1109).
44
11-11. Setup
Burn on the Fly
Press ENT.
Burn on the Fly
On
Use the arrow button to change the On or
Off setting then press ENT or press ESC
to go back to the setup screen (11-09).
45
Copy Master
Octave Systems, Inc.
If the system does not connect with the
hard drive, the LCD will display an error
message as shown to the left.
There is no HDD!
Display Time
On
Use the up or down arrow button to
change the On Off, then press ENT.
11-12 Burn Mode - DVD
This function controls the writing methods to CD discs, these
are Disc at Once (DAO) and Track at Once (TAO). This only
applies to CDs and not DVDs. However if a CD disc is copied
in a DVD Copy Master, and the DVD writer does not support
the mode you have selected, the Copy Master will automatically
switch to another mode. The default setting is DAO.
11-14 Button Sound - DVD
This function controls the On and Off button for sound. The
default setting is On.
11-14. Setup
Button Sound
Press ENT.
Button Sound
On
Use the arrow button to change the “On”
and “Off” setting, then press the ENT or
ESC button to go back to the setup
screen (11-12).
Press ENT.
11-12. Setup
Burn Mode
Press ENT to enter the next figure. The
default is DAO.
Burn Mode
DAO
11-15 Device Info - DVD
This function shows the devices installed.
11-13 Display Time – DVD
11-15. Setup
Device Info
Press ENT then press the down arrow
slowly to see each drive. The following
diagrams show a 7 drive Copy Master
CD.
00 IDEO Master
DVDDUAL:PIONEER
Press the down arrow.
Display time shows the copying time.
11-13. Setup
Display Time
Press ENT.
46
47
Octave Systems, Inc.
Copy Master
01 IDEO Slave
HDD : WDC
Press the down arrow.
07 IDE 6 Master
DVDDUAL:PIONEER
Press the down arrow.
02 IDE 1 Master
DVDDUAL:PIONEER
Press the down arrow.
08 IDE 7 Master
DVDDUAL:PIONEER
Press ESC twice to get out of this menu.
03 IDE 2 Master
DVDDUAL:PIONEER
Press the down arrow.
11-16 System Info - DVD
04 IDE 3 Master
DVDDUAL:PIONEER
Press the down arrow.
05 IDE 4 Master
DVDDUAL:PIONEER
Press the down arrow.
06 IDE 5 Master
DVDDUAL:PIONEER
Press the down arrow.
This function will show the controller firmware information on
the LCD.
11-16. Setup
System Info
Press ENT.
CD Duplicator
The LCD will display the firmware
information.
1-7 Ver: 2.38P
11-17 Quick Erase - DVD
This function will quick erase the data on the CD/DVD-Rewritable discs. It will take a short time to do it.
48
49
Octave Systems, Inc.
Copy Master
11-17. Setup
Quick Erase
Press ENT.
All data will be
lost, erase? Yes
Use the arrow button to select the“Yes”
or “No” setting, then press the ENT or
press ESC to go back to the setup screen
(11-16).
All data will be
lost, erase? Yes
Use the arrow button to select the“Yes”
or “No” setting, then press the ENT or
press ESC to go back to the setup screen
(11-15).
Erasing disc
03:24 (Full)
The LCD will display the progress.
Erasing disc
00:24 (Quick)
The LCD will display the progress.
Full
Erase
OK: 01 Fail: 00
When the process is completed, the LCD
will display the result. Press ESC to go
back to the setup screen (11-15).
Quick Erase
OK: 01 Fail: 00
When the process is completed, the LCD
will display the result. Press ESC to go
back to the setup screen (11-15).
11-19 Auto Close Tray - DVD
This function is to automatically close the writer’s tray.
11-19 Setup
Auto Close Tray
Press ENT.
Auto Close Tray
5
The ‘5’ signify 5 seconds to close the
tray automatically. There are other
seconds to choose from.
11-18 Full Erase - DVD
This function will erase the data on the CD/DVD Re-Writable
disc. This takes a longer time than Quick Erase.
11-18 Setup
Full Erase
Press ENT.
11 Setup - CD
50
This function contains a list of options, which allows the user to
change the original default settings. However, we suggest using
the original default settings for optimal operation.
51
Octave Systems, Inc.
Copy Master
Burn Speed MAX
Use the down arrow button to change the
burn speed, then press ENT.
11-01 Language - CD
This option will set the language preference that will be
displayed on the LCD. Only English and Spanish are currently
supported. Other languages will be added in the future.
Press ENT.
11-01 Setup
Language
11-03 Read Speed - CD
This function will set the reading speed of the source which is
the CDROM or the Source Drive. The default is maximum.
11-03. Setup
Read Speed
Press ENT and ESC to exit.
Read Speed
Maximum
Use the down arrow button to change the
read speed, then press ENT.
Press ENT or down arrow
Language
English
Press ENT or ESC to exit
(not all systems are set up with Spanish).
Language
Spanish
11-04 Auto Start Drive - CD
This setting controls the writers that will auto start the copy or
test function when a blank disc is inserted into the writer drive.
The default setting is Off.
11-02 CD Burn Speed - CD
11-04. Setup
Auto Start Drive
Press ENT and ESC to exit.
Auto Start Drive
Off
Use the arrow button to change the
number or the Off setting, then press
ESC to go back to the setup screen (1104).
This function controls the maximum writing speed of the writers.
The standard setting is Max which will use the highest writing
speed of the writers.
11-02. Setup
Burn Speed
Press ENT.
52
53
Octave Systems, Inc.
Copy Master
Use the arrow button to change the On or
Off setting, then press ENT or press
ESC to go back to the setup screen (1106).
Auto Verify
Off
11-05 Start-up Menu - CD
This function allows the user to select one of the menu items
which will become the first menu item to show when the
duplicator is turned on. The default is 1. Copy.
11-05. Setup
Start-up Menu
Start-up Menu
1. Copy
Press ENT and ESC to exit.
Use the arrow button to select an item to
be the first menu seen when the
duplicator is turned on (1-11), then press
ENT.
11-07 Auto Compare - CD
This function controls the On and Off of the Auto Compare (the
data between master and target discs after discs are copied).
The default setting is Off.
11-07. Setup
Auto Compare
Press ENT.
Auto Compare
Off
Use the arrow button to change the “On”
or “Off” setting then press ENT or press
ESC to go back to the setup screen (1107).
11-06 Auto Verify - CD
This function controls the On and Off of the Auto Verify (this
checks the target discs if they can be read correctly in the CDROM or Source Drive after copying). The default setting is
Off.
11-06. Setup
Auto Verify
Press ENT.
11-08 Auto Prescan - CD
This function controls the On and Off of the Auto Prescan (this
verifies that the master of the disc can be read correctly and test
the reading speed). Default setting is Off.
11-08. Setup
Auto Prescan
54
Press ENT..
55
Copy Master
Octave Systems, Inc.
Auto Prescan
Off
Use the arrow button to change the On or
Off setting, then press ENT or press
ESC to go back to the setup screen (1108).
Eject Discs
Do Not Eject
Use the arrow button to select Do Not
Eject, then press ENT or press ESC to
go back to the setup screen (11-09).
11-09 Eject Disc - CD
11-10 Burn on the Fly - CD
This function controls the ejection of discs by the CD/DVD writer.
Three options are available: The Eject Good Only setting will only
eject the passed discs automatically and leave the failed ones in the
writers. The Eject All Discs will have all the writers eject the
discs no matter whether the operation is successful or a failure.
The Do Not Eject option will have all discs remain in the writers
when the job is completed and you will have to eject discs from
the writers manually. The default is Eject Good Only.
This function controls the writing methods to the CD/DVD disc.
When the setting is On, the data will perform a direct copy from
the source drive to the target drives. When the setting is Off,
the data will load into a particular temporary partition on the
hard drive. Afterward, the data to be copied will come from the
source partition. The default is ON.
11-09. Setup
Eject Disc
Eject Disc
Eject Good Only
Eject Disc
Eject All Discs
Press ENT.
Use the arrow button to select Eject
Good Only, then press ENT or press
ESC to go back to the setup screen (1109).
11-10. Setup
Burn on the Fly
Press ENT.
Burn on the Fly
On
Use the arrow button to change the On or
Off setting then press ENT or press ESC
to go back to the setup screen (11-09).
There is no HDD!
If the system does not connect with the
hard drive, the LCD will display an error
message as shown to the left.
Use the arrow button to select Eject All
Discs, then press ENT or press ESC to
go back to the setup screen (11-09).
11-11 Burn Mode - CD
This function controls the writing methods to CD discs, these
56
57
Copy Master
Octave Systems, Inc.
are Disc at Once (DAO) and Track at Once (TAO). This only
applies to CDs and not DVDs. However if a CD disc is copied
in a DVD Copy Master, and the DVD writer does not support
the mode you have selected, the Copy Master will automatically
switch to another mode. The default setting is DAO.
11-11. Setup
Burn Mode
Press ENT.
Burn Mode
DAO
Press ENT to enter the next figure. The
default is DAO.
11-12 Button Sound - CD
11-13. Setup
Device Info
Press ENT then press the down arrow
slowly to see each drive. The following
diagrams show a 7 drive Copy Master
CD.
00 IDEO Master
CD-RW : ASUS
Press the down arrow.
01 IDEO Slave
HDD : WDC120
Press the down arrow.
02 IDE 1 Master
CD-RW : ASUS
Press the down arrow.
03 IDE 2 Master
CD-RW : ASUS
Press the down arrow.
04 IDE 2 Master
CD-RW : ASUS
Press the down arrow.
This function controls the On and Off button for sound. The
default setting is On.
11-12. Setup
Button Sound
Button Sound
On
Press ENT.
Use the arrow button to change the “On”
and “Off” setting, then press the ENT or
ESC button to go back to the setup
screen (11-12).
11-13 Device Info - CD
This function shows the devices installed.
58
59
Octave Systems, Inc.
05 SCSI ID00 L00
CD-RW : ASUS
Copy Master
Press the down arrow.
11-15 Quick Erase - CD
06 SCSI ID00 L01
CD-RW : ASUS
Press the down arrow.
07 SCSI ID00 L02
CD-RW : ASUS
Press the down arrow.
08 SCSI ID00 L03
CD-RW : Teac
Press ESC twice to get out of this menu.
This function will quick erase the data on the CD/DVD-Rewritable discs. It will take a short time to do it.
11-15. Setup
Quick Erase
Press ENT.
All data will be
lost, erase? Yes
Use the arrow button to select the“Yes”
or “No” setting, then press the ENT or
press ESC to go back to the setup screen
(11-15).
Erasing disc
00:24 (Quick)
The LCD will display the progress.
Quick Erase
OK: 01 Fail: 00
When the process is completed, the LCD
will display the result. Press ESC to go
back to the setup screen (11-15).
11-14 System Info - CD
This function will show the controller firmware information on
the LCD.
11-14. Setup
System Info
Press ENT.
11-16 Full Erase - CD
CD Duplicator
The LCD will display the firmware
information.
1-7 Ver: 1.76T
60
This function will erase the data on the CD/DVD Re-Writable
disc. This takes a longer time than Quick Erase.
61
Octave Systems, Inc.
Copy Master
11-16 Setup
Full Erase
Press ENT.
12-01. Adv Setup
UnderRun Protect
Press ENT.
All data will be
lost, erase? Yes
Use the arrow button to select the“Yes”
or “No” setting, then press the ENT or
press ESC to go back to the setup screen
(11-16).
UnderRun Protect
On
Use the arrow button to select the “On”
or “Off” setting, then press the ENT or
press ESC to go back to the setup screen
(12-01).
Erasing disc
03:24 (Full)
The LCD will display the progress.
12-02 Overburn
This function “squeezes” more data onto the disc than originally
intended. The default setting is Off.
When the process is completed, the LCD
will display the result. Press ESC to go
back to the setup screen (11-15).
Full
Erase
OK: 01 Fail: 00
12 Advanced Setup
12-02. Adv Setup
Overburn
Press ENT.
Overburn
Off
Use the arrow button to select the “On”
for Overburn , then press ENT, or the
“Off” setting, then press ENT. Press
ESC to go back to the setup.
Some of the advance setup functions allow the user to change
the system configuration. Changes should be made only when
you are fully familiar with Advanced Setup. To enter the
function, press the ESC button for two seconds.
12-03 Read Error Skip
12-01 Under Run Protect
This function controls the On and Off for the Buffer Under-run
Protection (ex. Burn Proof, Safe-burn, Just-link, seamless link,
etc.). The default setting is ON.
62
This function controls error skipping while the source drive is
reading. When an error is detected during source loading, the
duplicator will stop loading and display a read error message. If
the setting is "On", there will be no message shown even if
there is an error in reading. You can use this function to copy
certain CD/DVD's with errors made on purpose. The default
setting is Off.
63
Octave Systems, Inc.
Copy Master
12-03. Adv Setup
Read Error Skip
Press ENT.
Read Error Skip
Off
Use the arrow button to select the “On”
or “Off” setting, then press the ENT or
press ESC to go back to the setup screen
(12-03).
12-05. Adv Setup
Verify HDD
Press ENT.
Verify Disk
or Partition? Disk
Use the arrow button to change the
setting to “Disk” then press the ENT or
press ESC to go back to the setup screen
(12-05).
Verify Disk or
Partition? Parti
Use the arrow button to change the
setting to “Parti” then press the ENT or
press ESC to go back to the setup screen
(12-05).
12-04 Format Hard Disk
Works only when a hard disk is connected
This setting will allow you to initiate the hard drive and delete
all images.
12-04. Adv Setup
Format HDD
Press ENT.
All data will be
lost, format? Yes
Use the arrow button to select the “On”
or “Off” setting, then press the ENT or
press ESC to go back to the setup screen
(12-04).
There is no HDD!
If the system does not connect with the
hard drive, the LCD will show an error
message as shown to the left.
12-06 Burn-in
This function is a burn-in test function. It will run the emulate
writing continuously. Between each cycle of the emulate write,
the discs in the writers will be ejected automatically and reinsert again for continuous testing.
12-06. Adv Setup
Burn-in
Press ENT.
12.5 Verify HDD
Works only when a hard disk is connected
This function will verify an entire hard disk or any selected
partitions of a hard drive if they can be read correctly.
64
65
Octave Systems, Inc.
Copy Master
Burn-in
Test
The data will not be written to the blank
CD/DVD discs and will remain blank
after testing.
Sel burn-in num:
Run Continuous
Use the down arrow button to change the
Run Continuous to set the number of
times. Press ENT or ESC button to go
back to the setup screen (12-06).
Burn-in
Erase & Copy
Press ENT to update. When the update
process is complete, the system will reboot and stop at 1. Copy.
Update Firmware xxxx
To XXXX? Yes
12-08 Compare Firmware
12.08. Adv Setup
Compare Firmware
Press ENT.
This will compare new installed
firmware to the master disc.
The system will repeat the erase and write
function on the CD/DVD-RW discs.
Only discs labeled as Re-writable can use
this information.
12-09 H/W Diagnostics
This function will detect what devices are connected and test
them. The LCD will display the progress of the test.
12-07 Update Firmware
12.07. Adv Setup
Update Firmware
12-09. Adv Setup
H/W Diagnostic
Press ENT.
↑↓ Enter ESC
Hold ESC to exit
The LCD will ask the user to do the
button test. Follow the LCD instructions
and test each function button.
Place the new firmware disc in the ROM
drive. Press ENT.
After button function testing, the system will perform a self-test
on the SDRAM, the hardware connection test, and flash test.
Every test process will be displayed on the LCD. It will take a
few minutes to get the results of the hardware diagnostics. It is
an easy way to know if the system is working properly.
66
67
Octave Systems, Inc.
Test finished
Copy Master
The LCD will display when the test is
finished. Press the ESC button to go
back to the setup screen (12-09).
12-11 CD+G (for Karaoke)
12-11. Adv Setup
CD+G
Press the ENT.
CD+G
OFF/ON
The default is OFF. Press the down
arrow key to select ON. Press ENT.
12-10 Load Default
This function will reset the system back to the factory default
settings. Different settings can cause the duplicator to react
differently. It is always best to reset the unit if in doubt about
other settings.
12-10. Adv Setup
Load Default
Load Default
Config? Yes
Load Default
OK
Press ENT.
12-12 ISRC & MCN
This function supports ISRC & MCN which are special copying
formats.
Press ENT.
The LCD will display the process is
complete. Press ESC to return to (12-10).
12-12. Adv Setup
ISRC & MCN
Press ENT.
ISRC & MCN
Off
Press up or down arrow to change. Press
ENT.
12-13 Switch USB Mode (not available)
12-13 CD Text
Mainly for audio CD that has the ability to store text – e.g. song
68
69
Octave Systems, Inc.
Copy Master
titles and artist names. The default is OFF.
12-14. Adv Setup
CD-TEXT
Press ENT.
CD-TEXT
ON
Press up or down arrow to change. Press
ENT.
Chapter Four: Trouble Shooting & Tech
Support
1.
No display on the LCD and the fans do not operate
when the power switch is turned on.
• Check the connection of the power cable and see that the
power outlet is “live.”
2.
LCD displays an error message.
• During operations such as Copy, Test, Compare, and
Verify, you may press the "ESC" button to abort the
operation. An error message will be displayed on the
LCD. Some CD/DVD writers that abort can cause the
duplicator to hang and you must turn the power off, then
on to restore normal operation.
• Failed reading may cause an error message on the display.
Change the master CD/DVD and try again.
3.
CD/DVD-ROM cannot read discs, and shows and error
message.
• Check the format of the master or the disc for damage.
• Use any of the CD/DVD writers to read the master. If this
is a 4 or 7 drive system, use the first writer to read the
master. To do this, change the source (8. Select Source) to
“02 IDE1 Master.” If it works the ROM drive may be
defective or not compatible with the CD/DVD disc being
read.
4.
Unit does not function.
• May be busy on a task.
• Button malfunction.
• Faulty controller.
12-15 Multisession DVD
This is specially designed for DVDs with multiple sessions.
The default is OFF.
12-15. Adv Setup
MultiSession DVD
Press ENT.
MultiSession DVD
Off
Press up or down arrow to change. Press
ENT.
70
71
Octave Systems, Inc.
5.
6.
7.
8.
9.
•
Copy Master
Copy completed but CD/DVD-R disc is not
readable/executable.
• Use compare function (5. Compare) to check the discs.
The failure rate is high.
• Lower the speed of the CD/DVD writers (11-2 Burn
Speed) and try again.
• Quality of the blank disc is bad.
Cannot boot up.
• Contact Tech Support 1-800-626-8539 X 220
Cannot find the 12.Adv. Setup function.
• Press and hold the ESC button for 2 seconds to enter the
Adv. Setup Under-run Protect function.
How do I cancel duplication while in progress?
Press, and hold, the ESC button for 2 seconds to cancel the
Copy, Test, or Verify functions. Any partially burned
CD/DVDs will be unusable. Or Power off the system.
Technical Support
Technical support can be found online here:
DVD Dual Formats - + Information
The "Plus" "Minus" means the DVD Copy Master can handle
both DVD Minus format & DVD Plus format.
The two different formats are essentially the same as far as the
consumer is concerned with the exception of which companies
are backing them.
Behind the plus camp is mainly Dell, Sony, and Yamaha
Behind the minus camp is mainly Pioneer, Toshiba, and Apple
Here is a link to an article that describes the situation:
http://www.cdfreaks.com/article/110
The DVD Copy Master dual format (plus and minus) handles
either format with ease. It removes the risk from the consumer.
http://www.octave.com/cgi-bin/shop/shop.cgi/choice/html_copymastersupport
If you cannot solve your problem our technical support staff
will assist you if your unit is still covered under warranty. In
order to efficiently handle all requests we require our customers
to start by filling in the Support Form found here:
http://www.octave.com/cgi-bin/shop/shop.cgi/choice/html_incident
Or call 1-800-626-8539 X 220
You will be contacted within one business day.
72
73
Octave Systems, Inc.
74

advertisement

Key Features

  • Standalone operation
  • High accuracy duplication
  • Easy to use LCD panel
  • Supports CD-R, CD-RW, DVD-R, DVD-RW
  • Built-in hard drive for image storage

Related manuals

Frequently Answers and Questions

What types of discs can the Copy Master duplicate?
The Copy Master can duplicate CD-R, CD-RW, DVD-R, and DVD-RW discs.
Does the Copy Master require a computer connection?
No, the Copy Master is a standalone device and does not require a computer connection.
How do I use the Copy Master to duplicate discs?
The Copy Master has a user-friendly LCD panel that guides you through the duplication process. You simply need to insert the master disc into the source drive and blank discs into the writer drives, then select the desired duplication mode.
Can I store images on the Copy Master's hard drive?
Yes, the Copy Master has a built-in hard drive that allows you to store images of CDs and DVDs for faster duplication.
What is the maximum writing speed of the Copy Master?
The maximum writing speed of the Copy Master varies depending on the type of disc and writer drive being used. Refer to the specifications section of this user guide for more information.
Download PDF

advertisement