PJ300C-LCD - RVR Elettronica SpA Documentation Server

PJ300C-LCD - RVR Elettronica SpA Documentation Server
PJ300C-LCD
User Manual
Volume 1
Manufactured by
Italy
File Name:
03_PJ300C-LCD_ING_1.0.indd
Version:
1.0
Date:
15/12/2006
Revision History
Document History
Date
Version
15/12/06
1.0
Reason
First Edition
Editor
J. H. Berti
PJ300C-LCD - User Manual
Version 1.0
© Copyright 2005 - 2006
R.V.R.
Elettronica SpA
Via del Fonditore 2/2c - 40138 - Bologna (Italia)
Telephone: +39 051 6010506
Fax: +39 051 6011104
Email:
[email protected]
Web:
www.rvr.it
All rights reserved
Printed and bound in Italy. No part of this manual may be reproduced,
memorized or transmitted in any form or by any means, electronic
or mechanic, including photocopying, recording or by any information storage and retrieval system, without written permission of the
copyright owner.











PJ300C-LCD
Table of Contents
1.
2.
3.
3.1
3.2
4.
4.1
5.
5.1
5.2
5.3
5.4
6.
6.1
6.2
6.3
7.
8.
8.1
8.2 8.3 8.4
8.5
8.6
9.
9.1
Preliminary Instructions
Warranty
First Aid
Treatment of electrical shocks
Treatment of electrical Burns
Unpacking
General Description
Quick guide for installation and use
Preparation
First power-on and setup
Operation
Management Firmware
Front and Rear Panel Description
Front Panel
Rear Panel
Connectors description
Technical Specifications
Working Principles
Power supply
Panel board
Power Amplifier
Control Board
Telemetry board
Interlock Output Interface
Identification and Access to the Modules
Identification of the Modules
User Manual
Rev. 1.0 - 15/12/06
1
1
2
2
2
3
3
5
5
7
10
11
19
19
20
21
22
23
23
23
23
24
24
24
25
25
PJ300C-LCD
This page was intentionally left blank
ii
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
IMPORTANT
The lightning flash with arrowhead, within a triangle, is intended to alert the user of the presence
of dangerous voltage that may constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the equipment.
1. Preliminary Instructions
WARNING: This equipment is fitted with earth
connections both in the power cord and for the chassis.
Make sure both are properly connected.
• General Warnings
Operation of this equipment in a residential area may cause
radio interference, in which case the user may be required
to take adequate measures.
This equipment should only be operated, installed and
maintained by “trained” or “qualified” personnel who are familiar
with risks involved in working on electric and electronic circuits.
“Trained” means personnel who have technical knowledge of
equipment operation and who are responsible for their own
safety and that of other unqualified personnel placed under
their supervision when working on the equipment.
“Qualified” means personnel who are trained in and
experienced with equipment operation and who are
responsible for their own safety and that of other unqualified
personnel placed under their supervision when working on
the equipment.
The specifications and data contained herein are provided
for information only and are subject to changes without prior
notice. R.V.R. Elettronica SpA disclaims all warranties,
express or implied.While R.V.R. Elettronica SpA attempts to
provide accurate information, it cannot accept responsibility
or liability for any errors or inaccuracies in this manual,
including the products and the software described herein.
R.V.R. Elettronica SpA reserves the right to make changes
to equipment design and/or specifications and to this manual
at any time without prior notice.
WARNING: Residual voltage may be present inside
the equipment even when the ON/OFF switch is set to
Off. Before servicing the equipment, disconnect the
power cord or switch off the main power panel and
make sure the safety earth connection is connected.
Some service situations may require inspecting the
equipment with live circuits. Only trained and qualified
personnel may work on the equipment live and shall be
assisted by a trained person who shall keep ready to
disconnect power supply at need.
R.V.R. Elettronica SpA shall not be liable for injury to
persons or damage to property resulting from improper use
or operation by trained/untrained and qualified/unqualified
persons.
WARNING: The equipment is not water resistant.
Any water entering the enclosure might impair proper
operation. To prevent the risk of electrical shock or
fire, do not expose this equipment to rain, dripping or
moisture.
Please observe local codes and fire prevention rules when
installing and operating this equipment.
WARNING: This equipment contains exposed
live parts involving an electrical shock hazard. Always
disconnect power supply before removing any covers
or other parts of the equipment.
Ventilation slits and holes are provided to ensure reliable
operation and prevent overheating; do not obstruct or
cover these slits. Do not obstruct the ventilation slits under
any circumstances. The product must not be incorporated
in a rack unless adequate ventilation is provided or the
manufacturer’s instructions are followed closely.
WA R N I N G : T h i s e q u i p m e n t c a n r a d i a t e
radiofrequency energy and, if not installed in compliance
with manual instructions and applicable regulations,
may cause interference with radio communications.
User Manual
• Notice concerning product intended purpose and use
limitations.
This product is a radio transmitter suitable for frequencymodulation audio radio broadcasting. Its operating
frequencies are not harmonised in designated user countries.
Before operating this equipment, user must
obtain a licence to use radio spectrum from the
competent authority in the designated user country.
Operating frequency, transmitter power and other
characteristics of the transmission system are subject to
restrictions as specified in the licence.
2. Warranty
La R.V.R. Elettronica S.P.A. warrants this product to be free
from defects in workmanship and its proper operation subject
to the limitations set forth in the supplied Terms and Conditions.
Please read the Terms and Conditions carefully, as purchase
of the product or acceptance of the order acknowledgement
imply acceptance of the Terms and Conditions.
For the latest updated terms and conditions, please visit our web
site at WWW.RVR.IT. The web site may be modified, removed
or updated for any reason whatsoever without prior notice.
The warranty will become null and void in the event the
product enclosure is opened, the product is physically
damaged, is repaired by unauthorised persons or is used for
purposes other than its intended use, as well as in the event
of improper use, unauthorised changes or neglect. In the event a defect is found, follow this procedure:
1 Contact the seller or distributor who sold the equipment;
provide a description of the problem or malfunction for
the event a quick fix is available.
Sellers and Distributors can provide the necessary
information to troubleshoot the most frequently encountered
problems. Normally, Sellers and Distributors can offer a
faster repair service than the Manufacturer would. Please
note that Sellers can pinpoint problems due to wrong
installation.
2 If your Seller cannot help you, contact R.V.R.
Elettronica and describe the problem; if our staff deems
it appropriate, you will receive an authorisation to return
the equipment along with suitable instructions;
3 When you have received the authorisation, you may
return the unit. Pack the unit carefully before shipment;
use the original packaging whenever possible and seal
the package perfectly. The customer bears all risks of
loss (i.e., R.V.R. shall not be liable for loss or damage)
until the package reaches the R.V.R. factory. For this
Rev. 1.0 - 15/12/06
/ 26
PJ300C-LCD
reason, we recommend insuring the goods for their full
value. Returns must be sent on a C.I.F. basis (PREPAID)
to the address stated on the authorisation as specified
by the R.V.R. Service Manager.
Units returned without a return authorisation may
be rejected and sent back to the sender.
4 Be sure to include a detailed report mentioning all
problems you have found and copy of your original
invoice (to show when the warranty period began) with
the shipment.
3.1.2
Please send spare and warranty replacement parts orders to
the address provided below. Make sure to specify equipment
model and serial number, as well as part description and
quantity.
R.V.R. Elettronica SpA
Via del Fonditore, 2/2c
40138 BOLOGNA ITALY
Tel. +39 051 6010506
3. First Aid
All personnel engaged in equipment installation, operation
and maintenance must be familiar with first aid procedures
and routines.
3.1
Electric shock treatment
3.1.1
If the victim is unconscious
Lay the victim down on his/her back on a firm
surface.
•
the neck and tilt the head backwards to free
One rescuer: give 2 quick rescue breaths after
each 15 compressions.
•
Two rescuers: one rescue breath after each 5
compressions.
•
Do not stop chest compressions while giving
artificial breathing.
•
Call for medical help as soon as possible.
If the victim is conscious
•
Cover victim with a blanket.
•
Try to reassure the victim.
•
Loosen the victim’s clothing and have him/her
lie down.
•
Call for medical help as soon as possible.
3.2
Treatment of electric burns
3.2.1
Large burns and broken skin
Follow the first aid procedures outlined below.
•
•
•
Cover affected area with a clean cloth or
linen.
•
Do not break any blisters that have formed;
remove any clothing or fabric that is stuck to
the skin; apply adequate ointment.
•
Administer adequate treatment for the type of
accident.
•
Get the victim to a hospital as quickly as
possible.
•
Elevate arms and legs if injured.
If medical help is not available within an hour, the victim is
conscious and is not retching, administer a solution of table
salt and baking soda (one teaspoon of table salt to half
teaspoon of baking soda every 250 ml of water).
the airway system (Figure 1).
Have the victim slowly drink half a glass of solution for four
times during a period of 15 minutes.
Stop at the first sign of retching.
Do not administer alcoholic beverages.
Figure 1
•
If needed, open the victim’s mouth and check
for breathing.
•
If there is no breathing, start artificial respiration
without delay (Figure 2) as follows: tilt the head
backwards, pinch the nostrils, seal your mouth
around the victim’s mouth and give four fast
rescue breaths.
3.2.2 Minor burns
•
Apply cold (not ice cold) strips of gauze or dress
wound with clean cloth.
•
Do not break any blisters that have formed;
remove any clothing or fabric that is stuck to
the skin; apply adequate ointment.
•
If needed, have the victim change into clean,
dry clothing.
•
Administer adequate treatment for the type of
accident.
•
Get the victim to a hospital as quickly as
possible.
•
Elevate arms and legs if injured.
Figure 2
•
/ 26
Check for heartbeat (Figure 3); if there is
no heartbeat, begin chest compressions
immediately (Figure 4) placing your hands in
the centre of the victim’s chest (Figure 5).
Figure 3
Figure 4
Figure 5
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
4. Unpacking
The package contains:
1 PJ300C-LCD
1 User Manual
1 Mains power cable
The following accessories are also available from Your R.V.R. Dealer:
• Accessories, spare parts and cables
4.1 General Description
The PJ300C-LCD is an radio broadcasting amplifier manufactured by R.V.R.
Elettronica SpA featuring adjustable RF power output up to 300 W under 50 Ohm
standard load and less than 20W drive power requirement.
The PJ300C-LCD has been designed for installation in a 19”x2HE box for rack.
The amplifier incorporates a low-pass filter to keep harmonics below the limits
provided for by international standards (CCIR, FCC or ETSI).
Two major features of PJ300C-LCD are compact design and user-friendliness.
Another key feature is its modular-concept design: the different functions are
performed by modules with most connections achieved through male and female
connectors or through flat cables terminated by connectors. This design facilitates
maintenance and module replacement.
The RF power section uses one MOSFET modulesable to deliver over 300W.
An LCD on the front panel and a push-button panel provide for user interfacing with
the microprocessor control system, which implements the following features:
• Output power setup
• Power output enable/disable
• User-selectable threshold settings for output power alarm (Power Good
feature)
• Measurement and display of amplifier operating parameters
• Communication with external devices, as programming systems or telemetry
systems through RS232 or I2C serial interface
Four LEDs on the front panel provide for machine status indication (ON, FAULT,
FOLDBACK, RF MUTE).
User Manual
Rev. 1.0 - 15/12/06
/ 26
PJ300C-LCD
The amplifier management software is based on a menu system. User has four
navigation buttons available to browse submenus: ESC, , , and ENTER.
The rear panel features the mains input connectors, RF power input and output
connectors, remote connector, protection fuse, interlock input and interlock output
connectors and a BNC connector that provides an RF test point with level being
13 dBm ±6dB lower than power ouput.
/ 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
5. Quick guide for installation and use
This section provides a step-by-step description of the machine installation and
configuration procedure. Follow these procedures closely upon first power-on
and each time any change is made to general configuration, such as when a new
transmission station is added or the exciter is replaced.
Once the desired configuration has been set up, no more settings are required
for normal operation; at each power-up (even after an accidental shutdown),
the amplifier defaults to the parameters set during the initial configuration
procedure.
The topics covered in this section are discussed at greater length in the next
sections, with detailed descriptions of all hardware and firmware features and
capabilities. Please see the relevant sections for additional details.
IMPORTANT: When configuring and testing the transmitter in which the amplifier
is integrated, be sure to have the Final Test Table supplied with the machine ready
at hand throughout the whole procedure; the Final Test Table lists all operating
parameters as set and tested at the factory.
5.1 Preparation
5.1.1 Preliminary checks
Unpack the amplifier and immediately inspect it for transport damage. Ensure that
all connectors are in perfect condition.
Provide for the following (applicable to operating tests and putting into service):
√ Single-phase 230 VAC or 115 VAC (-15% / +10%) mains power supply with
adequate ground connection
√ FM exciter with adjustable output power up to 20W (as a minimum), like RVR
Elettronica PTX30-LCD
√ For operating tests only: dummy load with 50 Ohm impedance and adequate
capacity (300 W as a minimum)
√ Connection cable kit including:
• Mains power cable
• Coaxial cable with BNC connectors for interlock signal connection between
exciter and amplifier
• RF connection cable between exciter and amplifier (50 Ohm coaxial cable with
“N”-type connectors)
• RF cable for output to load / antenna (50 Ohm coaxial cable with 7/8” connectors
as standard, or optional 7/16” connectors)
User Manual
Rev. 1.0 - 15/12/06
/ 26
PJ300C-LCD
5.1.2
Mains power supply
WARNING: Disconnect mains power supply before beginning these
procedures.
The supply unit (please see chapter 8.1 for a detailed description) is equipped
with fuse.
The mains power supply protection fuse are conveniently located on the rear panel
and are easily accessed (see figure 6.2): to check or replace a fuse, disconnect
machine from power mains, unscrew fuse cover and pull fuse out of socket.
The following fuses are used:
Main Fuse
(fig. 6.2 – item [9])
@ 230 Vac
@ 115 Vac
8A-T type 5x20
8A-T type 5x20
Table 5.1: Fuse
The main power supply unit is the full-range type and requires no voltage setup.
5.1.3 Connections
Connect the output of a suitable FM exciter (for instance, PTX30-LCD exciter
available from R.V.R. Elettronica) to the RF input (see figure 6.2) using a 50-Ohm
coaxial cable with “N”-type connectors. To begin with, set exciter to minimum output
power and switch if off.
Connect the amplifier INTERLOCK OUT output (figure 6.2) to the matching
INTERLOCK IN input fitted on all R.V.R. Elettronica exciters as standard; if your
exciter is a different brand, identify an equivalent input.
Connect the RF output (see figure 6.2) to an adequately rated dummy load or to
the antenna.
WARNING: Electric shock hazard. Never handle the RF output connector
when the machine is powered on and no load is connected. Injury or death
may result.
Ensure that the POWER switch on the front panel is set to “OFF”.
Connect the mains power cable to the MAINS terminal board on the rear panel
(see figure 6.2).
/ 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
Note : The mains must be equipped with adequate ground connection properly
connected to the machine. This is a pre-requisite for ensuring operator safety and
correct operation.
WARNING: The power supply connector is a terminal board. Ensure the wire
is not live before performing the connection.
Please see figure 5.2 for a hook-up diagram showing RF connection between
amplifier and exciter and load connection.
Figure 5.2: Connection to exciter
5.2 First power-on and setup
Follow this procedure upon first power-on and after making changes to the
configuration of the transmitter in which the amplifier is integrated.
Note : Standard factory settings are RF power output Off (Pwr OFF) and output
power set to upper limit (unless otherwise specified by customer).
5.1.2
Pilot exciter setup
Set up the pilot exciter so that the output power it delivers to a matched load equals
the maximum input power indicated in the amplifier final test table, switch off the
exciter and connect it to the amplifier.
User Manual
Rev. 1.0 - 15/12/06
/ 26
PJ300C-LCD
5.2.2 Power-on
When you have performed all of the connections described in the previous
paragraph, power on the amplifier using the suitable power switch on the front
panel (figure 6.1). Power on the pilot exciter.
5.2.3 Power check
Ensure that the ON light turns on (see figure 6.1). Machine name should appear
briefly on the display, quickly followed by forward and reflected power readings
(figure 5.2 - menu 1). If RF output is disabled, these readings will be zero.
5.2.4 How to enable Local mode and RF output
Check current mode setting and enable Local mode (if not already enabled)
following menu path Fnc ⇒ Loc ⇒ Local (figure 5.2): if left disabled, the machine
will not accept the next commands.
Check current RF output setting and enable output (if not already enabled) following
menu path Fnc ⇒ Pwr ⇒ ON (figure 5.2 - menu 4).
Check output power level and set to maximum level (if not already set to maximum)
from the Power Setup Menu, which you can call up by pressing these keys in the
order: ESC (opens Default Menu) ⇒ ENTER (hold down for 2 seconds) ⇒ SET
⇒ use key to set bar to maximum limit (figure 5.2 - menu 2).
5.2.5 Input power check and setup
Go to Pwr menu (figure 5.2 - menu 5) and look up forward output power Fwd,
reflected power Rfl and input power Inp readings.
With drive power set as specified in the Final Test Table, amplifier output power
should be 300W or higher: if needed, fine tune drive power until achieving rated
output power. Never exceed 330W output power.
Note : Normally, drive power should not exceed 20W (typically 15W): higher drive
power requirements are a symptom of abnormal operation.
/ 26
WARNING: Drive power levels above 20W (typically 25W), result in exceeding
input power, which causes a temporary amplifier lock-out (see section 5.3.4.1
- Alarms and Faults for more details).
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
5.2.6 RF output power level control
IMPORTANT: The amplifier incorporates Automatic Gain Control and output
power is modulated based on the power level set by the user and actual operating
conditions, such as temperature, reflected power and other parameters. Drive
power must be kept steady at maximum output power capacity. Please read section
5.3 for more details of RF power modulation.
Open the Power setup menu (figure 5.2 - menu 2) pressing the following keys
in the order:
ESC (opens Default Menu) ⇒ ENTER (hold down for 2 seconds)
Use SET menu
and
keys to set the desired amplifier output power; the SET
bar at the side provides a graphic display of set power, whereas the forward power
value shown on the display (Fwd: xxxx W) gives actual output power reading,
and may be lower than set power if an Automatic Gain Control is in limitedpower mode (please read section 5.3 concerning RF power modulation for more
details”.
Note : Output power can also be set in a Pwr OFF condition; in this condition,
(Fwd) output power reading on the display will be 0 (zero), whereas the SET bar,
which you can control using the keys, provides a graphic display of the amount of
power that will be delivered the moment you switch back to Pwr ON state.
5.2.7 Changing the Power Good alarm threshold
Change Forward Power Good alarm setting PgD from the Fnc menu as required
(factory setting is 50%).
Please read section 5.3.1 for more details.
5.2.8 Changing machine I2C address
Change the IIC address in the Mix menu as required (factory setting is 01).
Please read section 5.3.5 for more details.
5.2.9 How to enable Remote mode
If you wish to use the telemetry control feature, enable Remote control in the Fnc
menu (see section 5.3.1 for details).
Note : In the Remote mode, all local push-button controls except Remote/Local
(for switching back to Local mode) are disabled . Operating parameter readings
are available.
User Manual
Rev. 1.0 - 15/12/06
/ 26
PJ300C-LCD
5.3 Operation
1) Power on the amplifier (chap. 6.1) and ensure that the ON light turns on (chap.
6.1). Machine name should appear briefly on the display, quickly followed by
forward and reflected power readings (Menu 1), provided that the amplifier is
delivering output power.
Menu 1
1b) To modify power level setting, hold down the ENTER button until opening
the power setup menu.
The edit screen will look like this:
Menu 2
Next to SET indication, a bar provides a graphic display of preset output power.
The filled portion of the bar is proportional to set power level. Example
100% output power
Full bar
≅ 300W in output
50% output power
Half bar
≅ 150W in output
25% output power
1/4 bar
≅ 75W in output
The bottom line provides instantaneous power reading (297W in this instance);
press button
to increase level, press
to decrease it. When you have achieved
the desired level, press ENTER to confirm and exit the default menu. Please note
that the setting is stored automatically; in other words, if you press ESC or do not
press any keys before the preset time times out, the latest power level set will be
retained.
NOTE: This feature prevents the machine from delivering maximum power as
soon as output is enabled from menu 4, or in the event the machine is already
set to ON and energised.
2) Ensure that machine is not in a locked-out state. Press the ESC key (chap.
6.1) to call up the selection screen (Menu 3). Highlight Fnc and press ENTER
10 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
to confirm (chap. 6.1) and access the appropriate menu (menu 4).
If LOC is set to REMOTE (machine remote control), move cursor to LOC and
press ENTER (chap. 6.1); label will change to LOCAL, i.e. local control operation
mode.
In the same menu, ensure that power limiting is disabled: if PWR is set to OFF,
i.e. power output is disabled, move cursor to PWR. Press ENTER (chap. 6.1
- [9]) and label will switch to ON, i.e. power output enabled.
Press ESC (chap. 6.1) twice to go back to the default menu (menu 1).
3) Fine tune power setting from menu 2 (see description of item 1b) until achieving
the desired value.
WARNING: Machine is capable of delivering more than rated output power
(300 W); however, never exceed the specified power rating.
NOTE: Exciter drive power setting should never exceed 20W, or it will trigger
an Overdrive Alarm.
NOTE: If power is set to 0 W in the edit mode, the INTERLOCK OUT contact
(chap. 6.2) trips and external exciter power is immediately inhibited.
Next, you can review all operating parameters of the machine through the
management firmware.
Normally, the machine can run unattended. Any alarm condition is handled
automatically by the safety system or is signalled by the LED indicators on the
panel or by display messages.
NOTE: Standard factory settings are: output power set to upper limit (unless
otherwise specified by customer) and OFF.
5.4 Management Firmware
The machine features an LCD with two lines by 16 characters that displays a set
of menus. Figure 5.2 below provides an overview of machine menus.
The symbols listed below appear in the left portion of the display as appropriate:
(Cursor) - Highlights selected (i.e. accessible) menu.
(Filled arrow) - Editable parameter marker. This symbol appears in menus that
take up more than two lines to aid browsing.
(Three empty arrows) - Parameter is being edited.
(Empty arrow) - Current line marker; the parameter in this line cannot be
edited. This symbol appears in menus that take up more than two lines to aid
browsing.
User Manual
Rev. 1.0 - 15/12/06
11 / 26
PJ300C-LCD
Menu
Menu 22
Menu
Menu 11
Default Menu
Power Setup Menu
Menu
Menu 33
Selection Screen
Menu
Menu 44
Operation Menu
Menu
Menu 55
Power Menu
Menu
Menu 66
P.A. Menu
Menu
Menu 77
Alarm Menu
Menu
Menu 88
Miscellaneous menu
Menu
Menu 99
Version Menu
Figure 5.2
When the display is off, touching any key will turn on backlighting.
When the display is on, pressing the ESC button (chap. 6.1) from the default
menu (menu 1) calls up the selection screen (menu 3), which gives access to
all other menus:
Menu 3
To gain access to a submenu, select menu name (name is highlighted by cursor)
using button
or
and press the ENTER button (chap. 6.1).
Press ESC again (chap. 6.1) to return to the default menu (menu 1).
12 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
5.4.1 Operation Menu (Fnc)
In this menu, you can set power output On/Off, toggle between “Local” or “Remote”
control mode and set the Forward Power Good (PgD) threshold rate.
To edit an item, highlight the appropriate line using the UP and DOWN buttons and
then press and hold the ENTER button (chap. 6.1) until the command is accepted.
This way, Pwr setting is toggled between On and Off and Mod setting is toggled
between “x1” and “x10”. To edit the Power Good rate, simply select item “PgD”
and edit its value using buttons
and
; finally, press ENTER to confirm (chap.
6.1).
Menu 4
Pwr
Enables (ON) or disables (OFF) amplifier power output.
Loc
Modifies machine operation. In the LOCAL mode, the machine can read
and modify its operating parameters through the navigation keys and the
management firmware, whereas all other sources are locked out. In the
REMOTE mode, the machine can only read its operating parameters;
parameters are modified based on the commands received from other
connected telemetry systems.
PgD
Modifies Power Good (forward power) threshold. The Power Good rate
is a percent of machine rated power (300 W), not of forward output
power. This means that this threshold set at 50% will give 150 W
regardless of set power level. The Power Good feature enables output
power control and reporting. When output power drops below set Power
Good threshold, the machine changes the state of pin [7] of the DB15
“Remote” connector located on the rear panel (figure 6.3.2 - [6]).
5.4.2 Power Menu (Pwr)
This screen holds all readings related to machine output power:
Menu 5
Fwd
Rfl
Inp
User Manual
Forward power reading.
Reflected power reading.
Input power reading.
Rev. 1.0 - 15/12/06
13 / 26
PJ300C-LCD
Note that these are readings, rather than settings, and cannot be edited (note
the empty arrow). To change power setting, go to the default menu (menu 1) as
outlined earlier.
5.4.3 Power Amplifier (P.A) Menu
This screen is made up of four lines that can be scrolled using the buttons
, shows the readings relating to final power stage:
and
Menu 6
Note that these are readings, rather than settings, and cannot be edited (note the
empty arrow).
VPA
IPA
Voltage supplied to amplifier module.
Current absorbed to amplifier module.
Eff
Efficiency based on ratio of forward power to amplifier module power
in percent ( FWD PWR/(Vpa x Ipa) % ).
Tmp
Machine internal temperature.
5.4.4 Alarm Menu (Alm)
This menu shows any alarm conditions occurring during machine operation. Alarm
thresholds are preset at the factory.
Menu 7
FWD
RFL
INP
Counter of alarm conditions triggered by forward power.
Counter of alarm conditions triggered by reflected power.
Counter of alarm conditions triggered by input power.
Reset Alm Alarm counter reset.
14 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
Alarm conditions are numbered from 1 to 10 and reflect the following situations:
forward output power too high, reflected output power too high and input power
too high.
Alarm monitoring cycle is as follows: when an alarm condition is detected, alarm
counter increases by 1 unit, machine goes into lock-out state and the display shows
the cause for the stop (chap. 5.3.4.1). After 15 seconds, the machine attempts
to re-start; if a new alarm condition is detected, cycle is repeated over and over
again up to 10 times maximum.
If machine re-starts successfully, all alarm counters are reset after 30 minutes’
regular operation. After 10 alarm conditions triggered by the same cause, the
machine goes into fault lock-out mode, a lock-out mode warning appears on the
display and the “FAULT” LED turns on (chap. 6.1).
After the alarm condition has been rectified, the counter can be reset by highlighting
“Reset Alm” and holding down the ENTER key for some time (chap. 6.1).
5.4.4.1 Alarms and Faults
There are three types of alarms that can cause a machine lock-out and trigger
a “FAULT/LOCK” indication. When any one of the three alarm thresholds is
exceeded, the system will automatically switch to the warning screen (even
though the user is browsing system menus) and the following messages
are displayed:
1. Over Forward Power
Forward power threshold exceeded.
Alarm 1
2. Over Reflected Power
Reflected power threshold exceeded.
Alarm 2
3. Over Input Power
Input power threshold exceeded.
User Manual
Rev. 1.0 - 15/12/06
15 / 26
PJ300C-LCD
Alarm 3
Monitoring cycle is as follows:
• An alarm condition occurs;
• Alarm is displayed and device is locked out for 15 sec.;
• Operating conditions are restored;
• Verification.
Upon reaching the 10 cycle limit, a “FAULT” indication is triggered and the device
goes into lock-out mode; the appropriate LED turns on (figure 6.1) and this screen
is displayed:
I. Over Forward Power
Forward power alarm display.
Stop 1
II. Over Reflected Power
Reflected power alarm display.
Stop 2
III.Over Input Power
Input power alarm display.
Stop 3
16 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
Once the machine goes into “FAULT” mode, it will no longer attempt to re-start;
choose the appropriate reset procedure according to current machine setting:
• Machine set to LOCAL control mode - press “Reset Alm” in the alarm menu
(menu 7) or power off and back on again using the POWER switch (chap.
6.2).
• Machine set to REMOTE control mode - power off and back on again sending
the appropriate command via the DB15 connector (chap. 6.3.2 - item [14] and
[15]).
There is a fourth alarm that does not trigger a “FAULT” condition, but allows some
time until correct operating conditions are restored. When the temperature alarm
threshold is exceed (about 85°C), the following screen appears:
4. Over Temperature
Temperature power threshold exceeded.
Alarm 4
5.4.5 Miscellaneous Menu (Mix)
This menu lets you set machine address in an I2C bus serial connection:
Menu 8
IIC
I2C address setting. The I2C network address becomes significant when
the exciter is connected in an RVR transmission system that uses this
protocol. Do not change it unless strictly required.
5.4.6 Version Menu (Vrs)
This screen holds machine version/release information:
Menu 9
User Manual
Rev. 1.0 - 15/12/06
17 / 26
PJ300C-LCD
Note that these are readings, rather than settings, and cannot be edited (note the
empty arrow).
Rel
Dat
Tab
18 / 26
Firmware release information.
Release date.
Shows table loaded in the memory.
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
6. Front and Rear Panel Description
This section describes the components found on the front and rear panel of
PJ300C-LCD.
6.1 Front Panel
1
2 3 4 5 6
7 8 9 10
11
12
Figure 6.1
[1] AIR FLOW
[2] ON
[3] FAULT
[4] FOLDBACK
[5] R.F. MUTE
[6] CONTRAST
[7] ESC
[8]
[9]
[10] ENTER
[10] DISPLAY
[11] POWER
User Manual
Air flow for the forced ventilation.
Green LED - Turns on when amplifier is powered on.
Red LED - Turns on when machine is in permanent fault lock-out
mode.
Yellow LED - Turns on when foldback current limiting (Automatic
Gain Control) is intervened.
Yellow LED - Turns on when exciter power output is inhibited by an
external interlock signal.
Display contrast trimmer.
Press this button to exit a menu.
Navigation button used to browse menu system and edit
parameters.
Navigation button used to browse menu system and edit
parameters.
Press this button to confirm a modified parameter and open a
menu.
Liquid Crystal Display
AC mains ON/OFF switch.
Rev. 1.0 - 15/12/06
19 / 26
PJ300C-LCD
6.2 Rear Panel
1
2
9
3
10
4 5
6 7
11 12
8
13
14
15 16
Figure 6.2
[1]
[2]
[3]
[4]
PLUG
FAN
R.F. OUTPUT INTERLOCK IN
[5] EXT AGC
[6] REMOTE
[7] GSM ANT
[8] REMOTE
[9] FUSE BLOCK
[10]R.F. TEST
[11]24VDC IN
[12]SERVICE
[13]INPUT PWR
[14]INTERLOCK OUT
[15]INTERLOCK IN
[16]FOLDBACK 1-2
20 / 26
Mains supply plug, 90 - 260V 50-60 Hz.
Fan for the forced ventilation of the amplifier.
RF output connector, N-type, 50Ω.
Interlock input BNC connector: when central conductor is
connected to ground, the transmitter is placed into forced
standby mode.
Trimmer for the control of the delivered power in function
of the FWD fold input (FWD EXT AGC) and RFL fold input
(RFL FOLD AGC).
DB15 connector for telemetry of the machine.
Reserved for Future Uses - SMA connector for GSM
Antenna.
Reserved for Future Uses - DB25 connector for telemetry of
the machine.
Fuse carrier. Use a screwdriver to access the fuse. Contains
the general protection fuse rated 8AT 5x20.
RF test output, approx. 13 dBm wrt the RF output power
level
Not Used - External 24Vdc supply input. Negative (black)
and Positive (red).
DB9 connector for interconnection with other devices
and for factory parameters programming (only for factory
programming)
RF input connector, N-type, 50Ω.
Interlock output BNC connector: when the transmitter goes
into stand-by mode, the (normally floating) central connector
is connected to ground.
Reserved for Future Uses - Interlock input BNC connector:
Reserved for Future Uses - Trimmer for the control of the
delivered power in function of the foldback inputs
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
6.3 Connectors description
6.3.1 Service (for factory setting purposes only)
Type: Female DB9
1
2
3
4
5
6
7
8
9
NC
TX_D
RX_D
Internally connected to 6
GND
Internally connected to 4
Internally connected to 8
Internally connected to 7
NC
6.3.2 Remote
Type: Female DB15
Pin Name
Type
1
Interlock
IN
2
Ext AGC FWD
IN
3
GND
4
SDA IIC
I/O
5
VPA Tlm
ANL OUT
6
FWD Tlm
ANL OUT
7
Power Good
DIG OUT
8
GND
9
GND
10 Ext AGC RFL
IN
11 SCL IIC
I/O
12 IPA Tlm
ANL OUT
13 RFL Tlm
ANL OUT
14 On cmd
DIG IN
15 OFF cmd
DIG IN
User Manual
Purpose
Inhibits power if closed to GND
Ext. signal,1-12V, for power limitation (AGC)
Ground
Serial for IIC communication
PA supply voltage: 3.9V F.S.
Forward power: 3.9V F.S.
Signalling of the activation by the grounding of the contact normally open (chap. 5.4.1)
Ground
Ground
Ext. signal,1-12V, for power limitation (AGC)
Clock for IIC communication
PA power supply: 3.9V F.S.
Forward power: 3.9V F.S.
A pulse towards ground (500 ms) triggers power output
A pulse to ground (500 ms) inhibits power output
Rev. 1.0 - 15/12/06
21 / 26
PJ300C-LCD
7. Technical Specifications
Parameters
GENERALS
Frequency range
Rated output power
Input power for rated output
Power supply type
AC Supply Voltage
DC Supply Voltage
AC Apparent Power Consumption
Active Power Consumption
RF Fan active Power consumption
RF module efficiency
Overall efficiency
Input device
Display
Overall Phisical Dimensions
Ambient working temperature
Spurious & harmonic suppression
Conditions
U.M.
MHz
W
W
Mains input voltage range
CPU backup Input Voltage
Front panel width
Front panel height
Overall depth
VAC
VDC
VA
W
W
%
%
mm
HE
mm
°C
dBc
PJ300C-LCD
87.5 ÷ 108
300
10
Mono phase
230 ±15%
540
500
13
65
58
4 pushbutton
Alphanumerical LCD - 2 x 16
483
2
370
0 to + 50 (operational -10)
>70 (75 typical)
(*) macchina in compressione input 18W
(*) macchina in compressione input 18W
(*) macchina in compressione input 18W
(*) macchina in compressione input 18W
Meets or exceeds all FCC and CCIR rules
RF INPUT
RF Input
Driver power for rated output
Connector
Impedance
Max input power before protection
Ohm
W
N type
50
11
W
20
RF OUTPUTS
RF Output
Connector
Impedance
Ohm
Connector
RF Monitor
Impedance
Output Level
Ohm
dB
N female type
50
BNC
50
13 +\-6 dBm
Referred to the RF output
BNC
BNC
For remote power inhibition (short is RF off)
For remote power inhibition (short is RF off)
DB9 F
Factory reserved for firmware program
DB15F
IIC + 5 analog / digital inputs, 5 analog / digital outputs
AUXILIARY CONNECTIONS
Interlock Input
Interlock Output
RS232 Serial Interface
Service
I2Cbus
Modem
RS485 Serial Interface
Remote Interface
Telemetry Interface
Connector
Connector
Connector
Connector
Connector
Connector
Connector
Connector
Connector
POWER REQUIREMENTS
AC Power Input
AC Supply Voltage
VAC
115 / 230 ±15%
AC Apparent Power Consumption
VA
W
540
500
0,93
VDE male
Active Power Consumption
Power Factor
Connector
DC Power Input
DC Supply Voltage
DC Current
VDC
ADC
FUSES
On Mains
On services
On PA Supply
On Aux VDE socket
1 External fuse F 8 T - 5x20 mm
MECHANICAL DIMENSIONS
Front panel width
Phisical Dimensions
Front panel height
Overall depth
Chassis depth
Weigh
mm
mm
mm
mm
kg
483 (19")
88(xxx")
390
370 (xxxx)
about 6
19" EIA rack
FWD fold
REF fold
RF ON
RF OFF
Interlock
FWD
REF
VPA
IPA
Power Good
I2Cbus
For P.A. A.G.C. purpose, min 0,5 Vcc
For P.A. A.G.C. purpose, min 0,5 Vcc
OPTIONS
Telemetry
code
code
code
code
115 Vac
TELEMETRY / TELECONTROL
Analogical level
Analogical level
Remote connector inputs
pulse
pulse
ON/OFF level
Analogical level
Analogical level
Remote connector outputs
Analogical level
Analogical level
ON / OFF level
Remote connector others
for remote power inhibition (short is RF off)
max 5 Vcc
max 5 Vcc
max 5 Vcc
max 5 Vcc
open collector
TELEMETRY-TELECONTROL SW
Telecon
Yes, via TLC300 or TLC2000
VARIOUS
Cooling type
Acoustic Noise
dBA
Forced, with internal fan
<75
Leq 3 min @ 1 m
STANDARD COMPLIANCE
Safety
EMC
Spectrum Optimization
22 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
8. Working Principles
8.1 Power Supply
The PJ300C-LCD power supply unit is a switching-type unit whose +50 V main
output powers the machine’s RF amplifier. The power supply also features
stabilizers for generating continuous +5 V and +18 V voltages for supplying the
other equipment circuits. Note that the power supply is a “direct from mains” type,
or rather it is without a transformer, and it can be connected to any voltage between
90 and 260 V without any adjustments or manual settings.
8.2 Panel board
The panel board accommodates the microcontroller that runs the machine control
software and all user interface elements (display, LED’s, keys, …).
This board is interfaced with other machine modules via flat cables and provides
for power supply, control signals and measurement distribution.
8.3 Power Amplifier
The final power stage is enclosed in a totally shielded metal container fixed to the
central part of the device.
The RF signal coming from the main board reached the pilot, it come amplified
and sent to the final stage which takes care of final amplification up to 300W.
The amplifier is made with one SD2942 and one attenuator of 6dB 50W.
In addiction to the actual RF amplification, this circuit carries out the following
functions:
• Control of the power level in output, depending on the setting
• Reduction of the power supplied when in presence of high-level reflected
power
• Measure of the input power (ensemble the control board)
• Measure of the forward and reflected power by means of directional couplers
• Measure of the current absorbed by the power amplifier
• Measure of the temperature
• Low-pass filtering of the RF signal in output
This board also features an RF sampling of approximately 13dBm ±6dBm RF with
respect to the output, which is available on a BNC connector below the transmitter
output connector. This sample is is useful for verifying the characteristics of the
carrier, but not for verifying those of the upper harmonics.
User Manual
Rev. 1.0 - 15/12/06
23 / 26
PJ300C-LCD
8.4 Control Board
The main function of this board is to check and correct the MOSFET polarization
voltage of the RF amplifier section.
It also provides the measurement of the absorbed current and contains a circuit
for signaling power supply unit faults.
If no alarms are present, the voltage is adjusted only depending on the set output
power, with a feedback mechanism based on the reading of the power really
delivered (AGC).
The voltage is also affected by other factors, such as:
• Excess of reflected power.
• External AGC signals (Ext. AGC FWD, Ext. AGC RFL).
• Excess of temperature.
• Excess of absorbed current from the RF module.
8.5 Telemetry board
This board is designed to inform the user of the equipment operation state. All
input and output signals are available on the DB15 connector.
The same board also features the “INTERLOCK” BNC connector for disabling the
device. By grounding the central pin, the output power is reduced to zero until the
connection is removed.
When an R.V.R. amplifier is used, this connector is linked to the power amplifier
REMOTE or INTERLOCK by means of a BNC-BNC connection. In case of amplifier
faults, the central conductor is grounded thus forcing the machine to enter in
stand-by mode.
8.6 Interlock Output Interface
The interlock output interface serves to generate the signal of INTERLOCK
OUT, on the board is present one jumper which if set in opposite way reveres the
working logic.
24 / 26
Rev. 1.0 - 15/12/06
User Manual
PJ300C-LCD
9. Identification and Access to the Modules
9.1 Identification of the Modules
The PJ300C-LCD is made up of various modules linked to each other through
connectors so as to make maintenance and any required module replacement
easier.
9.1.1 Upper view
The figure below shows the equipment upper view with the various components
pointed out.
1
2
4
3
5
6
7
figure 9.1
[1]
[2]
[3]
[4]
[5]
[6]
[7]
User Manual
Power Supply (PSL600)
Control Board (SL045DR1101)
Panel Board (SL007PC2002)
Cooling Fan (VTL9G824G102)
RF Module Board (SL123RF1001)
Telemetry Board (SLTLMTXLCD03)
Interlock Output Interface (SL123IN1001)
Rev. 1.0 - 15/12/06
25 / 26
PJ300C-LCD
This page was intentionally left blank
26 / 26
Rev. 1.0 - 15/12/06
User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement