PL-40R 2 - Support

PL-40R 2 - Support
PL40NE01-1.book
33 ページ
2002年7月23日 火曜日 午後6時52分
Applying Effects to Tones
Applying Effects to Tones
1
4
Selector dial
2
[
]/[
]
3
EFFECT/(L. METER)
[+]/[–]
This piano provides you with a selection of effects that you
can apply to tones.
Effect Blocks
The following shows how the effects of this piano are
organized.
Configuring Effect Settings
Use the following procedures to configure the DSP, reverb, or
chorus effects.
To configure the DSP effect setting
1.
2.
Press the EFFECT/(L. METER) button.
Press the [ ] button twice to display the DSP
effect setting screen.
J DSP
DSP effects are applied to the connection between the sound
source and output (PA). You can select distortion and
modulation effects.
J REVERB
Reverb simulates the acoustics of specific types of
environments. You can choose from among 8 different reverb
effects, including “Room” and “Hall”.
J CHORUS
3.
Use the [+] and [–] buttons or the selector dial to
select a DSP effect type.
Š Select “OFF” to turn off the DSP effect.
Š The display exits the DSP effect setting screen if
you do not perform any operation for about 10
seconds. You can also exit the DSP effect setting
screen by pressing the EXIT/NO button.
The chorus effect gives sound greater depth by causing it to
vibrate. You can choose from among 8 different chorus
effects, including “Chorus” and “Flanger”.
Š See the list on page A-11 for information about the types of
DSP, CHORUS and REVERB effects that are available.
426-E-035A
E-33
PL40NE01-1.book
34 ページ
2002年7月23日 火曜日 午後6時52分
Applying Effects to Tones
To configure the reverb effect setting
1.
2.
Press the EFFECT/(L. METER) button.
Use the [+] and [–] buttons or the selector dial to
select a reverb effect type.
Š Select “OFF” to turn off the reverb effect.
Š The display exits the reverb effect setting screen if
you do not perform any operation for about 10
seconds. You can also exit the reverb effect setting
screen by pressing the EXIT/NO button.
To configure the chorus effect setting
1.
2.
3.
Press the EFFECT/(L. METER) button.
Press the [ ] button to display the chorus
effect setting screen.
Š Playing a demo tune (page E-11) automatically changes
the effect to the one that is assigned to the tune. You
cannot change or cancel a demo tune effect.
Š Changing the effect setting while sound is being output by
the piano causes a slight break in the sound when the
effect changes.
Š A number of tones, called “DSP tones” include automatic
DSP settings to bring out the full effect of the tone. If you
assign a DSP tone to a keyboard part (Upper1, Upper2,
Lower1, or Lower2), DSP turns on automatically and the
DSP selection changes*1 in accordance with the settings of
the DSP tone. Also, the mixer Mode DSP on/off setting for
the keyboard part to which the DSP tone is assigned is
turned on.*2
*1. When the mixer Mode DSP setting is turned on for
Upper1, the DSP selection and mixer Mode DSP on/off
setting of Upper2, Lower1, and Lower2 are
unchanged, even if you assign a DSP tone to them.
*2. The mixer Mode DSP on/off settings for all the other
parts are automatically turned off. Because of this,
DSP effects previously applied to these parts are
cancelled, which can make their tone sound different.
Š Whether or not an effect is applied to the parts that are
sounding also depends on mixer Mode Reverb Send,
Chorus Send, and DSP on/off settings. See “Using the
Mixer” on page E-46 for more information.
Š The reverb and chorus of parts whose mixer Mode DSP
setting is turned on is determined by the system setting of
the keyboard settings, and not by mixer Mode settings. See
“Keyboard Settings” on page E-71 for more information.
Use the [+] and [–] buttons or the selector dial to
select a chorus effect type.
Š Select “OFF” to turn off the chorus effect.
Š The display exits the chorus effect setting screen
if you do not perform any operation for about 10
seconds. You can also exit the chorus effect
setting screen by pressing the EXIT/NO button.
E-34
426-E-036A
PL40NE01-1.book
35 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to
Play Back a Music Library Tune
Using the Advanced Lesson System to Play Back a Music Library Tune
1
4
7
Selector dial
[+]/[–]
PLAY/PAUSE
2
5
8
[
]/[
]
TEMPO [
]/[
3
6
9
]
REW/PREV
3.
Selecting a Tune
4.
While the Music Library tune selection screen is
on the display, use the [ ] and [ ] buttons to
select the Music Library group you want.
Use the [+] and [–] buttons or the selector dial to
select the song you want.
Example:
See the Tune Reference at the back of this
manual (page A-15) for information about the
Music Library group for each of the built-in
tunes.
Press the [+] button six times.
Press the MUSIC LIBRARY button.
Š This causes the Music Library Mode indicator
lamp to light, and displays the Music Library
tune selection screen.
Š The display exits the Music Library tune selection
screen if you do not perform any operation for
about 10 seconds. You can also exit the Music
Library tune selection screen by pressing the
EXIT/NO button.
Š If you do not perform any operation within about
10 seconds, the display changes to the main
Music Library screen.
Š Pressing the MUSIC LIBRARY button or the [
[ ] buttons displays the Music Library tune
selection screen again.
426-E-037A
FF/NEXT
To select “Nocturne 9-2”, first press the [ ]
button once to select the Music Library group.
To select a tune
2.
STOP
Example:
The music library contains a wide variety of built-in tunes,
ranging from the classics to popular standards.
1.
MUSIC LIBRARY
Š When you press the EXIT/NO button again to exit the
Music Library Mode, a number of parameters are restored
to settings that were in effect when you entered the Music
Library Mode. See the “Recall Items” column of the
“Parameter List” at the back of this manual (page A-17) for
information about which parameter settings are restored.
]/
E-35
PL40NE01-1.book
36 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Play Back a Music Library Tune
Playing a Tune
To play a tune
1.
2.
Select the tune you want to play.
Press the PLAY/PAUSE button to start play of
the tune.
1
2
3.
Fingering
1
2
3
4
5
6
Note pitch
Tempo value
Measure number
Beat number
Dynamic mark
Measure number
Beat number
Key Lighting Precaution
To stop play, press the STOP button.
Š The tune you select continues to play until you
stop it.
Š To turn off repeat play, select “Off” for the
“Repeat” setting on the “Setting: Lesson” screen
(page E-75).
Š While a tune is playing, you can change to another tune.
The change is made as soon as you select a different tune,
even if the current tune is not finished playing.
Key Lighting System Operation and Display
Contents During Music Library Play
Keyboard keys light to show the keys that should be pressed
to play along with Music Library tunes as they play back. At
the same time, the display shows fingerings, chord forms,
notes, tempo and other information.
Š Avoid using the key lighting system in a dark or dimly lit
room. The lighting or flashing of the red key lights can
cause an unpleasant effect in the dark.
Adjusting the Tempo
Each tune has a preset default tempo (beats per minute) that
is set automatically whenever you select a tune. While the
tune is playing, you can change the tempo setting to a value
in the range of 30 to 255.
To adjust the tempo
1.
While the indicator lamp above the TEMPO
buttons is lit, use the TEMPO buttons [ ]/[
or the selector dial to adjust the tempo.
]
Š The TEMPO button indicator lamp is not lit and
tempo adjustment cannot be performed while the
menu screen is on the display. To exit the menu
screen and return to the tone/rhythm screen,
press the FUNCTION button.
[
] (+) ..... Increase tempo (make it faster)
[
] (–) ..... Decrease tempo (make it slower)
Š Pressing both the [ ] and [ ] TEMPO buttons at the
same time automatically returns the currently selected
rhythm to its default tempo.
Š A number of tunes have tempo changes part way through
in order to produce specific musical effects.
E-36
426-E-038A
PL40NE01-1.book
37 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Play Back a Music Library Tune
Pausing Playback
Skipping Forward
To pause playback
To skip forward
1.
2.
Press the PLAY/PAUSE button while a tune is
playing to pause it.
Pressing the PLAY/PAUSE button again
resumes play from the point where it was
paused.
1.
While a tune is playing or paused, hold down
the FF/NEXT button to skip forward, in onemeasure steps.
Š The measure and beat numbers on the display
change to indicate the current location.
2.
Š After you press STOP to stop playback, pressing PLAY/
PAUSE restarts play from the beginning of the tune.
Release the FF/NEXT button to start song
playback from the measure whose number is
shown on the display.
Š Skipping forward cannot be performed while playback is
stopped.
Skipping Back
To skip back
1.
While a tune is playing or paused, hold down
the REW/PREV button to skip back, in onemeasure steps.
Š The measure and beat numbers on the display
change to indicate the current location.
2.
Release the REW/PREV button to start song
playback from the measure whose number is
shown on the display.
Š Skipping back cannot be performed while playback is
stopped.
Looping a Musical Phrase
Each of the built-in tunes is divided into fixed-length phrases.
You can select the phrase you want and “loop” it, which
means that the phrase plays again and again until you stop it.
You can also define your own phrase for looping.
To loop a preset phrase
1.
While tune playback is paused or in progress,
press the PHRASE REPEAT button.
Š This causes the indicator lamp above the button
to light. After a short beat count*, the first phrase
of the current tune starts to loop.
* Only when Pre Count is turned on. See
“Setting: Lesson” on page E-75 for more
information.
Š To move to the phrase before the current one,
press the REW/PREV button once. To move to the
phrase following the current one, press the FF/
NEXT button.
426-E-039A
E-37
PL40NE01-1.book
38 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Play Back a Music Library Tune
To create and loop your own phrase
Use the following procedure when you want to define your
own phrase for repeat play.
1.
2.
While the tune that contains the phrase you
want to create is playing, hold down the
PHRASE REPEAT button and press the REW/
PREW button when playback reaches the point
you want to define as the beginning of the loop.
Next, hold down the PHRASE REPEAT button
and press the FF/NEXT button when playback
reaches the point you want to define as the end
of the loop.
Š This causes playback to loop between the start
point and the end point you defined.
E-38
426-E-040A
PL40NE01-1.book
39 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to
Practice Along with a Music Library Tune
Using the Advanced Lesson System to Practice Along with a Music Library Tune
1
4
ARRANGE. LEVEL
START
2
5
LESSON PART
3
6
END
Arrangement Levels
The built-in tunes have three different arrangements, which
differ according to level of difficulty. You can select the
arrangement level that suits your particular abilities and
needs. The following describes the level of difficulty for each
of the arrangement levels.
STEP 1~3
AREA
Š Some tunes have fewer than three arrangement levels. If a
tune has only one arrangement level, the arrangement is
the same, regardless of which arrangement level is
selected. If a tune has only two arrangement levels, the
arrangement is the same for Arrangement Level A and
Arrangement Level B. For details, see the “Song List” at the
back of this manual (page A-15).
J Arrangement Level A
Much easier than the original arrangement of the tune. (1 or 2
notes for left-hand and right-hand parts, 1 or two notes per
measure for left hand part)
Selecting the Part You Want to
Practice
J Arrangement Level B
Easier than the original arrangement of the tune. (1 note for
left-hand part, rhythm same as original)
You can set up 3-step lesson for practice of the left-hand or the
right-hand part only, or for practice of the parts for both
hands at the same time.
J Arrangement Level C
Same level of difficulty as the original arrangement of the
tune.
To select a part for practice
1.
To select an arrangement level
1.
426-E-041A
Press the LESSON PART button to cycle
through the practice parts (L, R, L+R (BOTH))
until the one you want is displayed.
Š L : Practice the left-hand part
Press the ARRANGE. LEVEL button to cycle
through the arrangement level settings (LevelA, Level-B, Level-C) until the one you want is
displayed.
Š R : Practice the right-hand part
Š L+R (BOTH) : Practice the part for both hands
E-39
PL40NE01-1.book
40 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Practice Along with a Music Library Tune
Tune Types and Supported Parts
3.
Press any keyboard keys to play the melody
(right hand part).
J Two-hand Accompaniment Tunes
Piano Right Hand + Piano Left Hand (+ Obbligato)
J Auto Accompaniment Tunes
Š The key for the next note to be played flashes
while the keyboard waits for you to play it. When
you press any key to play the note, the key
remains lit as the note plays.
Melody (Right Hand) + auto accompaniment (Left Hand) +
Obbligato
3-Step Lesson
Š Accompaniment (or the left-hand part) waits
until you press any keyboard key. The
accompaniment notes stop playing automatically
if you do not press any key within about 10
seconds after the flashing starts. Pressing a
keyboard key restarts accompaniment.
The 3-step lesson feature takes you through the three distinct
steps described below to help you learn to play tunes on the
piano.
Š If you accidentally press more than one key in
succession, accompaniment is played for the
corresponding number of notes.
Step 1 – Master the timing.
In this step, pressing any key on the keyboard plays the
correct note, so you can concentrate on getting the timing
right without worrying about playing the right note. The submelody (obbligato) waits until you press a key before
proceeding to the next phrase.
1.
2.
Š Pressing more than one key at the same time
counts as a single melody note. Pressing a key
while another key is held down is counted as two
melody notes.
4.
To stop play at any time, press the STOP or
START/STOP button.
Select the Music Library tune you want to use.
Press the STEP 1 button to start Step 1 play.
Š After a count sounds*, the keyboard stands by
and waits for you to play the first note of the tune.
* Only when Pre Count is turned on. See
“Setting: Lesson” on page E-75 for more
information.
Š You can also use fast forward and fast reverse operations
with Step 1 play.
Š You can use phrase repeat with Step 1.
Key Lighting and Display Indicators During
Step 1 and Step 2
During lesson Step 1 and Step 2, notes, their lengths, and keys
you need to press to play them are indicated as described
below.
J Note
1
2
Fingering
Note pitch
The keyboard key you should press lights. The actual note is
shown in the staff notation area of the display. The display
also shows the fingers you should use to play notes.
J Note length
The length of a note is indicated by how long the note remains
in the on-screen staff after you press the required key.
E-40
426-E-042A
PL40NE01-1.book
41 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Practice Along with a Music Library Tune
J Next note
The keyboard key you will need to press next flashes. One
beat before you need to press the keys, the rate of flashing
becomes twice as fast.
Š With lesson Step 1 and Step 2, keyboard lighting and onscreen keyboard indication is turned off as soon as you
press the applicable keyboard key. For information aout
note length, check the on-screen staff notation.
Step 2 – Master the melody.
In this step, you use the display to learn which fingers you
should use and how loud or soft to play, and the key light
system to learn which keyboard keys to press. The submelody (obbligato) waits until your play the correct note, so
you can learn at your own pace.
1.
2.
Select the Music Library tune you want to use.
Press the STEP 2 button to start Step 2 play.
Š After a count sounds*, the keyboard stands by
and waits for you to play the first note of the tune.
* Only when Pre Count is turned on. See
“Setting: Lesson” on page E-75 for more
information.
Step 1 and Step 2 Key Light System Operation
3.
The following describes how the key light system works
during Step1 and Step 2 play.
Follow the key light system to press the correct
keyboard keys and play the melody (right hand
part).
■ The key for the next note to be played
flashes relativly slowy.
↓
Š The key for the next note to be played flashes
while the keyboard waits for you to play it. When
you press any key to play the note, the key
remains lit as the note plays.
■ One beat before you need to play the
note, the key starts to flash quickly.
↓
↓
Š Accompaniment (or the left-hand part) waits
until you press the flashing keyboard key. The
accompaniment notes stop playing automatically
if you do not press the flashing key within about
10 seconds after the flashing starts. Pressing the
flashing key restarts accompaniment.
■ The key light goes out when you press
the key.
Š If more than one key lights when you are using a
two-hand tune, it means that you must press all
of the keys that are lit.
■ The key remains lit, without flashing,
when the digital piano is standing by
waiting for you to play it.
4.
To stop play at any time, press the STOP or
START/STOP button.
Š You can also use fast forward and fast reverse operations
with Step 2 play.
Š You can use phrase repeat with Step 2. See “Looping a
Musical Phrase” on page E-37.
426-E-043A
E-41
PL40NE01-1.book
42 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Practice Along with a Music Library Tune
Dynamic Marks
The dynamic marks listed below appear on the display while
Music Library tunes are playing. Adjust the pressure you
apply to the keyboard in accordance with the mark that is on
the display.
pianissimo: Very soft
Š Use the lesson setting menu to turn voice fingering guide
on and off. See “Setting: Lesson” on page E-75 for more
information.
Š Note that voice fingering guide is available in either English
or Japanese. Use the lesson setting menu to select the
language you want to use. See “Setting: Lesson” on page
E-75 for more information.
piano: Soft
mezzo piano: Moderately soft
mezzo forte: Moderately loud
Step 3 – Play at normal speed.
forte: Loud
fortissimo: Very loud
crescendo: Gradually louder
decrescendo: Gradually softer
Crossed Finger Indications
This is where you enjoy actually playing the tunes you learn
using Step 1 and Step 2. The key light system still shows you
which keyboard keys to press, but accompaniment proceeds
at normal speed regardless of whether or not you play the
correct notes.
1.
2.
Display for playing the notes below with the right hand
only
1
Crossed finger display
Press the STEP 3 button to start Step 3 play.
Š Accompaniment (left hand part) starts to play at
normal speed.
The display also shows when you have to cross fingers to play
notes, and in which direction your fingers should cross.
Example:
Select the Music Library tune you want to play.
3.
4.
Follow the key light system to press the correct
keyboard keys and play the melody (right hand
part).
To stop play at any time, press the STOP or
START/STOP button.
Š The display indicates that the index finger should cross
over the thumb.
Voice Fingering Guide
Voice fingering guide uses a simulated human voice to call
out fingering numbers during Step 1 and Step 2 one-hand
part practice. If you need to press a key with your thumb, for
example, voice fingering guide says, “One!” In the case of a
chord to be played with your thumb, middle and little finger,
voice fingering guide says, “One, three, five!”
voice fingering guide calls out fingerings only when you do
not press the proper key when you should.
E-42
Š With Step 3 of two-hand practice, key lighting also indicates
note length. In this case, lighting indicates the keys you
should press, but the next key to be pressed does not flash.
Š With Step 3, the finger number for the next note does not
appear on the display. Only the finger number of the
current note is displayed.
Š You can also use pause, fast forward and fast reverse
operations with Step 3 play.
Š If you change the step, arrangement level, or lesson part
during step lesson playback, the change goes into effect
from the currently playing measure.
426-E-044A
PL40NE01-1.book
43 ページ
2002年7月23日 火曜日 午後6時52分
Using the Advanced Lesson System to Practice Along with a Music Library Tune
Key Lighting and Display Indicators During
Step 3
During lesson Step 3, notes, their lengths, and keys you need
to press to play them are indicated as described below.
Changing the Lesson Part Tone
You can select from among 271 built-in tones for the lesson
part. You can even change the lesson part tone setting while
lesson play is in progress.
See “Selecting a Tone” on page E-18 for more information.
J Note
The keyboard key you should press lights. The actual note is
shown in the staff notation area of the display. The display
also shows the fingers you should use to play notes.
Š Specifying the tune number for the same tune that is
currently selected returns the tone to the default setting for
that tune.
J Note length
You should keep a keyboard key depressed as long as it
remains lit. The note remains in the on-screen staff notation
and the on-screen fingering remain on the display for the
duration of the note.
J Next note
In Step 3, the key for the next note to be played does not flash.
3-Step Lesson Tempo Setting
Use the procedure under “Adjusting the Tempo” on page
E-26 to adjust the tempo for 3-step lesson play.
Things you can do during 3-Step Lesson
Š Pressing the PLAY/PAUSE button during Step 1, 2, or 3
play pauses the step lesson. Pressing PLAY/PAUSE again
resumes normal (non-lesson) playback of the tune from
the measure where you paused the step lesson. Pressing
a step selector button while the lesson is paused resumes
accompaniment for the corresponding step from the
measure where the lesson was paused.
Š Pressing the step selector button for the same step where
you paused the lesson restarts the lesson from the
beginning, using the same step.
Š You can use repeat during a lesson (Step 1, 2, or 3) and
during normal playback.
Š You can turn on a pre-count to sound at the beginning of
the song or at a repeat start point. See “Setting: Lesson”
on page E-75 for more information.
426-E-045A
E-43
PL40NE01-1.book
44 ページ
2002年7月23日 火曜日 午後6時52分
426-E-046A
PL40NE01-1.book
426-E-047A
45 ページ
2002年7月23日 火曜日 午後6時52分
PL40NE01-1.book
46 ページ
2002年7月23日 火曜日 午後6時52分
Using the Mixer
Using the Mixer
1
4
7
LAYER/(GROUP A/B)
[
]/[
2
5
]
PART/(MIXER)
3
6
ENTER/YES
Selector dial
[+]/[–]
EXIT/NO
Types of Parts
Parts
As mentioned above, the word “part” as used in relation to
this piano has the same meaning as it does in an orchestra or
band. It also refers to the Upper1, Upper2, Lower1, and
Lower2 parts of the keyboard that you use when layering or
splitting keyboard tones (page E-19).
The following example shows a typical list of parts when you
are using auto accompaniment with Upper1 and Upper2
tones layered in the melody keyboard range.
This piano is capable of producing a total of 30 different parts.
Parts can be broadly classified as one of two different groups:
Group A and Group B.
J Group A
Upper1
Group A parts are the ones the piano normally uses for auto
accompaniments and to produce the notes you play. There
are 14 Group A parts, including six “melody parts” (for
keyboard notes), and eight “accompaniment parts” (for auto
accompaniment).
2
Upper2
J Group B
3
Perc. (Percussion)
4
Drum
There are 16 Group B parts that the piano uses for sounding
MIDI input from an external source. Each of the Group B
parts also corresponds to one of the 16 tracks of the piano’s
sequencer (page E-53).
5
Bass
1
Melody Keyboard
6
Chord1
Accompaniment
7
Chord2
8
Chord3
9
Chord4
10
Chord5
Much like a real band, auto accompaniment patterns and
patterns you create with the sequencer are played using
multiple “parts”, such as chords, bass, and drum parts. The
mixer provides you with the means to turn individual parts
on (so they sound) and off (so they don’t), and to change the
tone, volume, pan, effect, and other parameters of each part.
E-46
426-E-048A
PL40NE01-1.book
47 ページ
2002年7月23日 火曜日 午後6時52分
Using the Mixer
The following is a general overview of the parts described above.
Group Name
Part Type
Part Name
Description
Upper1
These parts are used for keyboard play. See
“Upper1, Upper2, Lower1, Lower2” on page
E-19.
Upper2
Lower1
Melody
Lower2
Group A
Internal
[A]
Harmo1 (auto harmonize 1)
Harmo2 (auto harmonize 2)
Perc. (Percussion)
Harmonize notes used for auto harmonize. See
“Using Auto Harmonize” on page E-29.
Auto accompaniment parts. See “Using Auto
Accompaniment” on page E-23.
Drum
Accompaniment
Bass
Chord1 to Chord5
Group B
External
[B]
—
Pt1 to Pt16 (Part 1 to Part 16)
Š Select the Group A to make layer, split, or auto
accompaniment settings.
Changing the Parameters of
a Part
Use the following procedure to change the parameters of each
individual part.
These parts correspond to external tracks 1 to
16 when recording or playing back with the
sequencer. They are also used when sounding
MIDI input from an external source. See
“Using MIDI” on page E-66.
Š Select the Group B to make MIDI or sequencer
settings.
3.
Use the [ ] and [ ] buttons or the selector
dial to select the part you want.
To change part parameters
1.
While holding down the FUNCTION button,
press the PART/(MIXER) button.
4.
Š This causes “MIXER” to appear on the display.
5.
Press the ENTER/YES button to display the sub
menu.
Use the [ ] and [ ] buttons to select
parameter whose setting you want to change.
Š See “Parameter List” on page A-17 for more
information about parameters.
2.
While holding down the FUNCTION button,
press the LAYER/(GROUP A/B) button to
toggle between the two groups and display the
one you want.
Group A: [A]
Group B: [B]
426-E-049A
E-47
PL40NE01-1.book
48 ページ
2002年7月23日 火曜日 午後6時52分
Using the Mixer
6.
Use the [+] and [–] buttons or the selector dial to
change the setting of the currently selected
parameter.
Š Press the EXIT/NO button to return to the part
selection screen in step 3 of this procedure.
Š Any time during the above procedure, you can
select another part by pressing the PART/
(MIXER) button.
7.
Repeat steps 2 through 6 to change the settings
of other parameters if you want.
Š When changing parameter settings, you can play
notes on the keyboard as you change parameter
settings to see what effect your settings have.
8.
After you are finished making the settings you
want, press the EXIT/NO button.
Mixer Parameters
This section provides detailed explanations of each of the
mixer parameters, and their setting ranges.
Tone Parameters
J Part On/Off: On, Off
This parameter can be used to turn each part on (sounds) and
off (does not sound). The current on/off status of a part is
indicated by the on-screen level meter. See “Level Meter
Screen” on page E-13 for more information.
J Volume: 0 to 127
This parameter adjusts the overall volume of each part.
J Pan: –64 to 63*
Use this parameter to adjust the pan setting (volume balance
between the left and right speakers). A value of 0 puts the
speakers in balance, so the stereo center is halfway between
the two speakers. A smaller value shifts the stereo center left,
while a larger value shifts it right.
* When “On” is selected for the DSP you are using, these
settings are applied in accordance with each DSP
parameter setting.
Effect Parameters
The mixer lets you control the effects applied to each
individual part, making it different from the Effect Mode,
whose settings are applied to all parts in general.
J Tone: 271
J Reverb Send: 0 to 127
This parameter controls the tones assigned to each part.
This parameter controls how much reverb is applied to a part.
A setting of 0 turns reverb off, while a setting of 127 applies
maximum reverb.
Š You can also change the tone assignment with the TONE
buttons. The tone you select is applied to the currently
selected part.
Š Use DRUM tone group values for the “Drum” and
“Percussion” parts.
Š You cannot select DRUM tone group values for “Bass”, or
“Chord” parts.
Š Changing the tone assigned to the Upper1 also changes
the tone assigned to Harmo1. Changing the tone assigned
to the Upper2 also changes the tone assigned to Harmo2.
E-48
J Chorus Send: 0 to 127
This parameter controls how much chorus send is applied to
a part. A setting of 0 turns chorus send off, while a setting of
127 applies maximum chorus send.
Š “Chorus Send” does not work with drum sounds.
J DSP: On, Off
You can use this parameter to turn DSP off for a particular
channel, or to turn it on.
426-E-050A
PL40NE01-1.book
49 ページ
2002年7月23日 火曜日 午後6時52分
Using the Mixer
Tuning Parameters
You can use these parameters to individually tune each of the
parts individually.
J Coarse Tune: –24 to 24
This parameter tunes individual parts in semitone units,
which means that changing the value by 1 changes the tuning
by one semitone.
Š The setting you make here is added to the transpose
setting described in “Transposing the Piano” on page
E-31.
Š “Coarse Tune” does not work with drum sounds.
J Fine Tune: –64 to 63
This parameter allows fine tuning of individual parts. A
setting of –64 lowers the tuning by one semitone from normal,
while 63 represents a rise of one semitone. This setting is
applied by combining it with the “Tune setting” item of the
Keyboard Settings.
426-E-051A
E-49
PL40NE01-1.book
50 ページ
2002年7月23日 火曜日 午後6時52分
Registration Memory
Registration Memory
1
4
ENTER/YES
BANK
2
5
EXIT/NO
3
REGISTRATION
STORE
Registration Memory Features
Š Registration memory contents can be saved and recalled
while any one of the following conditions exists.
Reigstration memory lets you store uo to 16 keyboard setups
(4 sets × 4 banks) for instant recall whenever you need them.
The following is a list of settings that are saved in registration
memory.
* While the normal tone name and rhythm name screen
is on the display
* During song sequencer playback or playback standby
* During song sequencer recording (registration
memory recall only)
Registration Memory Settings
Š Rhythm
Š Tempo
Š Layer on/off
Š Split on/off
Š Auto harmonize on/off
Initial Settings
BANK A
Area
TONE
RHYTHM
Š Sustain length
1
004:E.Piano1
16Beat 1
Š Reverb type
2
Stereo Piano
8Beat 1
Š DSP type
3
004:E.Piano1
Pop Rock 2
Š Part on/off (Group A)
4
Full Organ
R&B
Area
TONE
RHYTHM
1
022:Harmnica
Shuffle Pop 1
2
Flute
8Beat Ballad 2
3
091:SpaceChr
16Beat Ballad 3
4
030:Dist.Gt1
Rock 1
Š Auto harmonize type
Š Chorus type
J The following settings are saved for the melody
part.
Š Part tone setting
Š Part pan
Š Part volume
Š Coarse tuning
Š Fine tuning
Š Part reverb level
Š Part chorus level
BANK B
Š Part DSP on/off
E-50
426-E-052A
PL40NE01-1.book
51 ページ
2002年7月23日 火曜日 午後6時52分
Registration Memory
BANK C
Area
TONE
RHYTHM
1
Clavi
Dance 1
2
017*PercOrg2
Swing 1
3
Flute
Bossa Nova 1
4
Strings 1
Broadway
Area
TONE
RHYTHM
1
Stereo Piano
Piano Ballad 1
2
Mellow Piano
Jazz Waltz
3
Stereo Piano
Arpeggio 1
4
Stereo Piano
2Beat
BANK D
To save a setup in registration
memory
1.
Select a tone and rhythm, and otherwise set up
the keyboard the way you want it.
Š See “Registration Memory Settings” on page E-50
for details on what data is stored in the
registration memory.
2.
Use the BANK button to select the bank you
want.
Š Note that the display exits the registration
memory save screen if you do not change the
setting within 10 seconds after displaying it. If
this happens, press the BANK button again.
Example:
BANK A selected.
Setup Names
You can assign setups into one of 16 areas, which you can
select using BANK buttons 1 through 4 and the four
REGISTRATION buttons. Area names range from A-1
through D-4 as shown below.
3.
While holding down the STORE button, press a
REGISTRATION button (1 to 4).
Example:
The following display appears when you press
the 2 button.
4.
1
2
Use the BANK button to select the bank. Each press
of the BANK button cycle through the bank numbers
from A to D.
Pressing one of the REGISTRATION buttons (1 to
4) selects the corresponding area in the currently
selected bank.
The bank (A to D) and area (1 to 4) where the
setup was stored appears on the display
momentarily. After the bank and area
disappear, release the REGISTRATION and
STORE buttons.
Š Whenever you save a setup and assign it a setup name,
any setup data previously assigned to that name is
replaced with the new data.
426-E-053A
E-51
PL40NE01-1.book
52 ページ
2002年7月23日 火曜日 午後6時52分
Registration Memory
To recall a setup from
registration memory
1.
2.
Use the BANK button to select the bank.
Press the REGISTRATION button (1 to 4) for
the area whose setup you want to recall.
Š The bank (A to D) and area (1 to 4) from which the
setup was recalled appears on the display
momentarily.
Š Pressing a REGISTRATION button without using the
BANK button to select a bank first recalls the setup from the
area in the bank you last selected.
E-52
426-E-054A
PL40NE01-1.book
53 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Using the Sequencer
1
4
7
SEQUENCER
ENTER/YES
2
5
Selector dial
3
6
START/STOP
[
]/[
]
[+]/[–]
EXIT/NO
The sequencer provides you with powerful tools for
recording up to 10 songs into piano memory. You can record
auto accompaniments and the notes you play with them, or
you can build your creation part-by-part using the
sequencer’s 17 tracks.
How the Sequencer Works
About Tracks
The sequencer’s system track is used for recording auto
accompaniments. More precisely, it records the eight parts
that make up auto accompaniment, the four melody parts
(Upper1, Upper2, Lower1, Lower2), and two parts required
for harmony when auto harmonize is turned on.
Each of the 16 tracks can be used to record the notes played
for one particular musical instrument (tone).
About Songs and Tracks
The sequencer provides you with capabilities that are similar
to a tape recorder. You can record things you play on the
keyboard and play them back. There is enough memory to
store about 15,500 notes, and this total memory can be
divided between up to 10 “songs”.
Each song consists of up to 17 tracks, one system track and 16
tracks numbered 1 through 16. You can record tracks one at a
time and then play them back at the same time, which layers
everything together and give you the potential of becoming a
one-person orchestra.
Š Each track is independent of the others. This means that if
you make a mistake while recording, you need only to rerecord one track.
Š You should use Tracks 1 through 9 and Tracks 11 through
16 mainly for non-drum sound tones, and Track 10 mainly
for drum sound tones. Otherwise, tones may not be correct
during playback or when saving data to an SMF file.
Recording Techniques
There are two techniques you can use for sequencer
recording: realtime recording and punch in recording.
J Realtime Recording
With realtime recording, you record what you play on the
keyboard as you play it.
J Punch In Recording
This method lets you re-record from a specific section of a
song that is already in memory. You can use punch-in
recording to correct mistakes you made during real-time
recording.
426-E-055A
E-53
PL40NE01-1.book
54 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Sequencer Record Data
The following are the three basic types of data recorded by the
sequencer.
Š The time signture setting (stored in the song header).
Š Initial track parameters (stored in the song header).
Š Parameter changes and operations performed during
recording (stored at the point in the recording where you
make them).
You should also note that the data you can record in the
system track is different from the data you can record in
the 16 tracks.
J Parameter Changes and Operations During
System Track Recording
Š Notes played on the keyboard (including chords in the
accompaniment keyboard range)
Š Pedal operations
Š Rhythm changes
Š Tone changes
Š Tempo changes
Š Auto accompaniment mode changes
Š Auto accompaniment controller operations (except for
START/STOP button): INTRO, FILL-IN, BREAK,
VARIATION 1/2, SYNCHRO START/STOP, ENDING.
Š Accompaniment keyboard range chords
Š Effect type changes
Š For more detailed information about the data that can be
recorded in each track, see the “Parameter List” at the back
of this User’s Guide (page A-17).
Track 1 to 16 Data
J Initial Track Parameters
Parameters Applied to All Tracks
The settings of the parameters listed below are stored as
header data and applied to all tracks. You cannot change
these settings part way through a song or for a particular
track.
Š Time signature (0, 2/4 to 7/4, 9/4, 12/4, 3/8, 5/8, 6/8, 7/8, 9/
8, 12/8)
Š Effect type
Š Tune setting (Master Tune, Baroque Pitch, Temperament)
When you start recording of the track, the settings of these
parameters are stored in the song header. You can change
these settings using the procedure under “Changing Song
Header Data” on page E-60.
Š Tone assignment
Š Mixer settings
J Parameter Setting Changes and Operations
During Track 1 to 16 Recording
Š Melody notes played on the keyboard
Š Pedal operations
System Track Data
Š Tone changes
J System Track Initial Parameters
When you start recording of the track, the settings of these
system tarck parameters are stored in the song header. You
can change these settings using the procedure under
“Changing Song Header Data” on page E-60.
Š Rhythm selection
Š Tone settings
Upper1, Upper2, Lower1, Lower2 tones, on/off status,
split point setting
Š Tempo
Š Transpose
Š Mixer settings
Settings are recorded for each auto accompaniment and
melody part and cannot be changed (except for mixer
volume) once recording starts.
Š Auto accompaniment mode
Š Auto harmonize on/off status
E-54
426-E-056A
PL40NE01-1.book
55 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Sequencer Memory Capacity
You can store about 15,500 notes in sequencer memory, which
can be divided among up to 10 songs. You can use all 15,500
notes for a single song, if you want.
Š Remaining memory capacity is indicated by a percentage
value that appears for a few seconds after you enter
record standby.
Š Recording stops automatically when memory becomes
full. Play of the auto accompaniment or rhythm pattern
you are using also stops when memory becomes full.
Š You can record up to 1,000 measures per tune.
Memory Data Notes
Š Starting a record operation deletes any data currently
stored in the selected song area.
Š Sequencer memory contents are retained even when you
turn off the piano. Power required for memory storage is
supplied by a built-in back-up lithium battery. See
“Lithium Battery” on page E-90 for important
information about the lithium battery.
Š Turning off piano power while a record operation is in
progress or standing by causes all sequencer contents to
be deleted.
426-E-057A
E-55
PL40NE01-1.book
56 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Sequencer Main Menus and Sub Menus
The following describes how to navigate around the sequencer mode’s main menus and sub menus to select functions and configure
settings.
Each press of the SEQUENCER button toggles between the play standby screen and the Main Menu.
Š When you press the EXIT/NO button to exit the sequencer Mode, a number of parameters are restored to settings that were in effect
when you entered the sequencer Mode. See the “Recall Items” column of the “Parameter List” at the back of this manual for
information about which parameter settings are restored (page A-17).
Š Each press of ENTER/YES while the “Delete” menu is on the display accesses the “Delete” sub menu.
Š The main menu that appears first is the one that was on the display when you last exited the main menus to the play standby screen.
Š The “Delete” sub menu that appears first is the one that was on the display when you last exited the “Delete” sub menus.
E-56
426-E-058A
PL40NE01-1.book
57 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Realtime Recording
6.
Š You can use the mixer to change the parameters
of auto accompaniment and melody parts.
Realtime Recording to the System Track
The following procedure contains only the most basic steps
for realtime recording. For other techniques you can use
during this procedure, see “Other System Track Realtime
Recording Techniques” on page E-58.
1.
Š After making the settings you want, press the
EXIT/NO button to return to the recording
screen.
7.
Press the SEQUENCER button.
Select the song area to which you want to
record.
Press RECORD button to enter the Realtime
Record Mode.
Š The button’s indicator lamp flashes and the
sequencer goes into system track record standby.
Š This causes the button’s indicator lamp to light,
indicating that sequencer is turned on.
2.
If you want to change mixer parameter settings,
hold down the FUNCTION button and press
PART/(MIXER) button and then configure the
settings you want.
8.
Play something on the keyboard to start actual
recording.
Š Use [+]/[–] buttons or the selector dial to select a
song area number in the range of 1 to 10.
Š After a few seconds, the display changes to the
play standby. You can also display the play
standby by pressing the EXIT/NO button.
3.
]/[
] buttons to select the setting you
Specify the time signature and make any
metronome settings you want to use while
recording.
Š Use “Metronome Setting 5 : “Metro”” in the
Setting Mode on page E-63 to make metronome
settings.
Š During recording, the metronome sounds (but is
not recorded) according to the settings you made
in step 4.
9.
Make the piano control panel settings you want
to use when you start your recording.
Š Select the tone, rhythm, and auto accompaniment
mode using the same procedures as those for
normal keyboard play. “Other System Track
Realtime Recording Techniques” on page E-58
also contains related information about these
settings.
Š See “System Track Data” on page E-54 for
information about what parameters you can set
prior to recording.
426-E-059A
Play what you want on the keyboard.
Š Auto accompaniment chord changes, as well as
pedal and other operations are also recorded.
Š After you select a setting, press the SEQUENCER
button or the EXIT/NO button to return to the
play standby screen.
5.
Current measure and beat numbers
Š If you want to input rests (blank spaces) at the
beginning of a song, press the START/STOP
button to start recording, and then input as many
rests as you want. Next, play what you want on
the keyboard.
Press the SEQUENCER button to display the
main sequencer menu.
Š Use the [
want.
4.
1
Š See “System Track Data” on page E-54 for more
information about the type of data that is
recorded.
10.
After you are finished playing what you want,
press the START/STOP button to stop
recording and change to the sequencer’s
playback screen.
Š Pressing the START/STOP button at this time
plays back what you just recorded. See “Playing
Back from Sequencer Memory” on page E-60 for
more information about playback.
E-57
PL40NE01-1.book
58 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Realtime Recording to Tracks 1 to 16
Š Using the Realtime Record Mode to record to a track that
already contains data replaces the existing data with the
new recording.
Š If you make a mistake while recording, you can start over
again from step 1 of the above procedure, or you can use
punch in recording (page E-59) to make modifications.
Other System Track Realtime Recording
Techniques
J To record without auto accompaniment
In step 5 of the above procedure, turn off auto
accompaniment (so none of the lamps above the MODE
button are lit).
Use Tracks 1 through 16 to add other parts to the
accompaniment and keyboard notes you record in the system
track. You can then turn tracks on and off during playback to
create the arrangement you want.
The recording procedure for tracks 1 through 16 is basically
the same as that for recording to the system track. Skip the
first two steps of the procedure if you go into the recording of
other tracks directly after you finish recording the system
track.
1.
Š This causes the button’s indicator lamp to light,
indicating that sequencer is turned on.
2.
Select the song area to which you want to
record.
Š Use [+]/[–] buttons or the selector dial to select a
song area number in the range of 1 to 10.
Š You can turn auto accompaniment on or off part way
through a recording, if you want.
Š After a few seconds, the display changes to the
play standby. You can also display the play
standby by pressing the EXIT/NO button.
J To use synchro start to start recording
At any time before you perform step 5 of the above
procedure, press the SYNCHRO START/STOP button.
Press the SEQUENCER button.
3.
Select the track you want to record.
Š Press the SEQUENCER button to display the
main menu, and then select “TrackSelect”.
Š Both auto accompaniment and recording will start when
you play a chord in the accompaniment keyboard range
during record standby prior to step 7.
J To insert an intro, fill-in, break, etc.
You can use any of the following buttons during realtime
system track recording: INTRO, FILL-IN, BREAK,
VARIATION 1/2, SYNCHRO START/STOP, ENDING.
Š A track that already contains recorded data is
indicated on the display by “ ”.
∗
J To synchro start recording with an intro pattern
At any time before you perform step 5 of the above
procedure, press the SYNCHRO START/STOP button and
then press INTRO.
Š Use the [+] and [–] buttons or the selector dial to
select a track.
4.
Š Recording will start and the intro will play, followed by
auto accompaniment when you play a chord in the
accompaniment keyboard range during record standby
prior to step 7.
Š You do not need to specify a time signature here
if you already have one recorded in the system
track.
J To start rhythm pattern play part way through a
recording
In step 6 of the above procedure, turn off auto
accompaniment (so none of the lamps above the MODE
button are lit). After recording is started, press one of the
VARIATION 1/2 buttons to start rhythm play (without
chords). Now you can use the MODE button to select an auto
accompaniment mode and play chords on the
accompaniment keyboard.
E-58
Specify the time signature and make any
metronome settings you want to use while
recording.
Š After you select a setting, press the SEQUENCER
button or the EXIT/NO button to return to the
play standby screen.
5.
Make the piano control panel settings you want
to use when you start your recording.
Š Select the tone and tempo setting using the same
procedures as those for normal keyboard play.
Š The tempo setting you used for last track
recorded in a song is used as that song’s initial
default tempo setting for playback.
426-E-060A
PL40NE01-1.book
59 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
6.
If you want to change mixer parameter settings,
hold down the FUNCTION button and press
PART/(MIXER) button and then configure the
settings you want.
Š After setting the parameters you want, press the
EXIT/NO button to return to the recording
screen.
7.
8.
Press the RECORD button. This puts the
sequencer into record standby.
Play something on the keyboard to start actual
recording.
Š If you want to start recording without playing
anything on the keyboard, press the START/
STOP button. A blank space (a series of rests) is
recorded until you play something.
Š During recording, the metronome sounds (but is
not recorded) according to current metronome
parameter settings.
9.
Play what you want on the keyboard.
Š Pedal and other operations are also recorded.
Š See “Track 1 to 16 Data” on page E-54 for more
information about the type of data that is
recorded.
10.
After you are finished playing what you want,
press the START/STOP button to stop
recording and change to the sequencer’s
playback screen.
Š Pressing the START/STOP button at this time
plays back what you just recorded. See “Playing
Back from Sequencer Memory” on page E-60 for
more information about playback.
Modifying Recorded Data with
Punch In Recording
Use punch in recording to make changes in parts you have
already recorded in a track.
With punch in recording, you listen to the playback of
previous recording, and start playing on the keyboard from
the point where you want to make your modifications.
Everything up to the point where you start playing is
retained, but everything after that point is replaced with your
new input.
Using Punch In Recording
Note that you should skip the first two steps of the following
procedure when you go into punch in recording to modify
something you have just recorded.
1.
Press the SEQUENCER button.
Š This causes the button’s indicator lamp to light,
indicating that sequencer is turned on.
2.
Select the song area that contains the song
whose data you want to modify.
Š Use [+]/[–] buttons or the selector dial to select a
song area number in the range of 1 to 10.
3.
4.
Š Using the Realtime Record Mode to record to a track that
already contains data replaces the existing data with the
new recording.
Š If you make a mistake while recording, you can start over
again from step 1 of the above procedure, or use punch in
recording (page E-59) to make modifications.
If you want to use the metronome during
recording, make the required metronome
settings.
Select the track whose contents you want to
modify.
Š Use the [
] button to select “TrackSelect”.
Š Use the [+] and [–] buttons or the selector dial to
select a track.
Š After you select a setting, press the SEQUENCER
button or the EXIT/NO button to return to the
play standby screen.
5.
Press the ENTER/YES button.
Š This enters the punch-in mode and causes the
RECORD button’s indicator lamp to flash.
426-E-061A
E-59
PL40NE01-1.book
60 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
6.
7.
Press the START/STOP button to start
playback of the selected track.
When playback reaches the point from which
you want to modify the track contents, start
playing the new notes on the keyboard.
Š Recording starts and playback of the track’s
current contents stops as soon as you play
something on the keyboard.
8.
After you are finished playing what you want,
press the START/STOP button to stop
recording and change to the sequencer’s
playback screen.
Š You can change the playback tone after starting playback
of the track’s contents in step 6, but the tone setting you
make is not recorded. After you start punch in recording (in
step 7), any changes you make in parameter settings are
recorded just as they are during normal recording.
Playing Back from Sequencer
Memory
Use the following procedure when you want to play back the
contents of sequencer memory.
Š Skip steps 1 and 2 of the following procedure if you have
just finished a real-time recording operation.
To play back from Sequencer memory
1.
Press the SEQUENCER button.
Š This causes the button’s indicator lamp to light,
indicating that sequencer is turned on.
2.
Select the user song area that contains the
song you want to play back.
Š Use the [+] and [–] buttons or the selector dial to
select the song area (Song 1~10).
Changing Song Header Data
3.
Press the START/STOP button to start
playback.
Š Use the TEMPO buttons [
the playback tempo.
You can use the following procedure to change the initial
mixer, tempo and other settings stored in the song header.
] and [
] to adjust
Š See the notes below for other operations you can
perform during playback.
To change the song header data
1.
2.
Press the SEQUENCER button.
Select the song area that contains the song
whose header data you want to change.
Š Use the [+]/[–] buttons or the selector dial to select
a song area number in the range of 1 to 10.
3.
4.
Set the tempo, mixer, and other song header
parameters you want.
Press the RECORD button.
Š This causes the current panel settings to replace
the song header parameter settings of the
currently selected song.
Š Press the EXIT/NO button to change from the
remaining memory screen to the record standby
screen (which shows the tone and rhythm). The
record standby screen appears automatically
after about 10 seconds if you do not perform any
operation while the remaining memory screen is
on the display.
5.
E-60
4.
Press the START/STOP button again to stop
playback.
Š Pressing the START/STOP button starts playback from the
beginning of the selected song.
Š You can play along on the keyboard during sequencer
playback. You can use layer and split for keyboard play.
Š You can use the mixer to adjust the volume level and
stereo points of the playback track. Such settings are
output from MIDI OUT when they are made.
Š You cannot change the MODE button setting during
sequencer playback.
Š During song playback, you can display a level meter screen
that shows the volume level of each part, as well as the
each part’s on/off status. See “Level Meter Screen” on
page E-13 for more information.
Press the EXIT/NO button.
426-E-062A
PL40NE01-1.book
61 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Configuring Global Recording Settings and Operations
The following are global settings you can configure and operations you can perform for recording with the sequencer.
1 Song selection
2 Recording track
3 Quantize execute
4 Meter
5 Metronome setting
6 Song name
7 Track delete
8 Song delete
9 All song delete
To make global settings
1.
Press the SEQUENCER button once.
Š This causes the button’s indicator lamp to light, indicating that sequencer is turned on.
2.
Select the user song area that contains the song whose global settings you want to change.
Š Use the [+] and [–] buttons or the selector dial to select the song area (Song 1~10).
Š After a few seconds, the display changes to the play standby. You can also display the play standby by pressing the
EXIT/NO button.
3.
Press the SEQUENCER button to display a main menu, and then use the [
item whose setting you want to change.
] and [
] buttons to display the
Š To display the “Delete” sub menu, first display the “Delete” main menu, and then press the ENTER/YES button.
Š The numbers to the right of the sample displays below correspond to the following sections that provide details on each
setting.
4.
When the item you want is on the screen, change it to the setting you want.
Š See the explanations following this procedure for details on making each setting.
5.
After the settings are the way you want, press the SEQUENCER button or the EXIT/NO button.
Š This returns to the sequencer play standby screen.
426-E-063A
E-61
PL40NE01-1.book
62 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Song Selection 1 : “Song Select”
You can use this screen to specify a song number from 1 to 10.
It comes in handy if you did not have a song selected when
you displayed the sequencer main menu, or if you want to
change the current song setting.
Recording Track 2 : “TrackSelect”
This setting selects the track for recording.
2.
3.
Press the ENTER/YES button.
In response to the confirmation message
(SURE?) that appears, press the ENTER/YES
button to execute the quantize operation, or the
EXIT/NO button to cancel the operation.
Š This performs the quantize operation.
Š The message “Completed!” appears on the
display for about one second, and then the piano
returns to main menu (Quantize) screen.
Š If there is not enough sequencer memory available, the
message “Error! Memory Full” appears on the display and
the quantize operation is not performed.
Quantize Execute 3 : “Quantize”
This setting determines the quantize* value after recording.
After recording, quantize adjusts the timing of notes input to
each track on the keyboard to match those selected by the
setting you make here.
* The track that is affected by the quantize operation is the
one that was selected when you displayed the global
setting screen.
1.
Use the [+] and [–] buttons or the selector dial to
change the setting.
Display Indicator
4
4T
8
Quantize quarter notes
Quantize quarter triplicate notes
Quantize 8 th notes
8T
Quantize 8 th triplicate notes
16
Quantize 16 th notes (initial value)
16 T
32
32 T
64
E-62
Meaning
Quantize 16 th triplicate notes
Quantize 32 nd notes
Meter 4 : “Beat”
This setting specifies the meter of the song.
Š If a song is already recorded with a rhythm, the meter of the
rhythm is set automatically.
Setting
Setting
0
12 / 4
2/4
3/8
3/4
5/8
4 / 4 (initial value)
6/8
5/4
7/8
6/4
9/8
7/4
12 / 8
9/4
Quantize 32 nd triplicate notes
Quantize 64 th notes
Š Use the [+] and [–] buttons or the selector dial to change the
setting.
426-E-064A
PL40NE01-1.book
63 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Metronome Setting 5 : “Metro”
J Letters and Numerals
The table below shows the letters and numerals that you can
input for a song name.
This setting controls whether or not the metronome sounds
during sequencer recording.
Display Indicator
Meaning
Off
Metronome off
On
Metronome on
Metronome sound:
The first beat is a chime, followed by a standard metronome
click for the other beats.
Š Use the [+] and [–] buttons or the selector dial to change
the metronome setting.
Song Name 6 : “SongName”
You can use this screen to assign a name to the currently
selected song.
1.
2.
On the sequencer sub menu, select
“SongNameEdit”, and then press the ENTER/
YES button.
Use [+] and [–] or the selector dial to scroll
through letters at the current cursor location.
Š Use the [ ]/[
and right.
3.
Track Delete 7 : “DeleteTrack”
Use the following procedure to delete the track associated
with the currently selected track. A track that already contains
recorded data is indicated on the display by “ ”.
1.
] buttons to move the cursor left
Use the [+] and [–] buttons or the selector dial to
select the track you want to delete, and then
press the ENTER/YES button.
Š In response to the confirmation message (SURE?)
that appears, press the ENTER/YES button to
execute the delete operation, or the EXIT/NO
button to cancel the operation.
After you are finished inputting the name, press
the ENTER/YES button to save the song under
the name you specified.
Š The message “Completed!” appears on the
display for about one second, and then the piano
returns to main menu (SongNameEdt) screen.
∗
Š To exit the procedure without deleting anything,
press the EXIT/NO button here.
2.
Press the ENTER/YES button to delete the
track.
Š The message “Completed!” appears on the
display for about one second, and then the piano
returns to Delete sub menu (DeleteTrack) screen.
426-E-065A
E-63
PL40NE01-1.book
64 ページ
2002年7月23日 火曜日 午後6時52分
Using the Sequencer
Song Delete 8 : “DeleteSong”
Use this operation to delete a song from a specific user song
area. A song that already contains recorded data is indicated
on the display by “ ”.
1.
∗
Use the [+] and [–] buttons or the selector dial to
select the song you want to delete, and then
press the ENTER/YES button.
Š In response to the confirmation message (SURE?)
that appears, press the ENTER/YES button to
execute the delete operation, or the EXIT/NO
button to cancel the operation.
Š Press the EXIT/NO button to abort the delete
operation without deleting anything.
2.
Press the ENTER/YES button to delete the
song.
Š The message “Completed!” appears on the
display for about one second, and then the piano
returns to Delete sub menu (DeleteSong) screen.
All Song Delete 9 : “DeleteSongAll”
Use the following procedure when you want to delete all
songs in memory.
1.
Press the ENTER/YES button.
Š In response to the confirmation message (SURE?)
that appears, press the ENTER/YES button to
execute the delete operation, or the EXIT/NO
button to cancel the operation.
Š To exit the procedure without deleting anything,
press the EXIT/NO button here.
2.
Press the ENTER/YES button to delete all the
songs.
Š The message “Completed!” appears on the
display for about one second, and then the piano
returns to Delete sub menu (DeleteSongAll)
screen.
E-64
426-E-066A
PL40NE01-1.book
426-E-067A
65 ページ
2002年7月23日 火曜日 午後6時52分
PL40NE01-1.book
66 ページ
2002年7月23日 火曜日 午後6時52分
Using MIDI
Using MIDI
What is MIDI?
The letters “MIDI” stand for “Musical Instrument Digital
Interface”, which is the name of a worldwide standard for
digital signals and connectors that makes it possible to
exchange musical data between musical instruments and
computers (devices) produced by different manufacturers.
MIDI compatible equipment can exchange keyboard key
press, key release, tone change, and other data as “messages”.
Though you do not need any special knowledge about MIDI
to use this piano as a stand-alone unit, MIDI operations
require a bit of specialized knowledge. This section provides
you with an overview of MIDI that will help to get you going.
MIDI Connections
MIDI messages are sent out through the MIDI OUT terminal
of one device to the MIDI IN terminal of another device over
a MIDI cable. To send a message from this piano to another
device, for example, you must use a MIDI cable to connect the
MIDI OUT terminal of this piano to the MIDI IN terminal of
the other device. To send MIDI messages back to this piano,
you need to use a MIDI cable to connect the other device’s
MIDI OUT terminal to the MIDI IN terminal of this piano.
To use a computer or other MIDI device to record and
playback the MIDI data produced by this piano, you must
connect the MIDI IN and MIDI OUT terminals of both devices
in order to send and receive data.
There is a third MIDI terminal named MIDI THRU, which
passes any MIDI messages received by the MIDI IN terminal
on to another device.
1
Computer, etc.
Š This piano also has a USB terminal that can be used to
connect to a computer. See “Connecting to a Computer” on
page E-69 for more information.
E-66
MIDI Channels
MIDI allows you to send the data for multiple parts at the
same time, with each part being sent over a separate “MIDI
channel”. There are 16 MIDI channels, numbered 1 through
16, and MIDI channel data is always included whenever you
exchange data (key press, pedal operation, etc.).
This piano is equipped with “multi-timbre” capabilities,
which means it can receive messages over all 16 MIDI
channels and play up to 16 parts at the same time. Keyboard
and pedal operations performed on this piano are sent out by
selecting a MIDI channel (1 to 16) and then sending the
appropriate message.
General MIDI
Though MIDI makes it possible to exchange musical data
between devices produced by different manufacturers, MIDI
musical data does not indicate the actual notes themselves,
but rather information on whether a keyboard key is pressed
or released, and the tone number.
If tone number 1 on a keyboard produced by Company A is
PIANO while tone number 1 on a Company B’s keyboard is
BASS, for example, data that is played using the PIANO tone
on Company A’s keyboard will be played using the BASS
tone on Company B’s keyboard. If a computer, sequencer or
other device with auto accompaniment capabilities is used to
produce music data for the Company A keyboard which has
16 parts (16 channels) and then that data is sent to the
Company B keyboard which can receive only 10 parts (10
channels), some of the parts will not sound.
To overcome problems such as these, the industry has come
up with standard numbering for tones, pads, and other
general factors that determine the sound source
configuration. This standard is called “General MIDI”.
General MIDI defines the tone numbering sequence, the
drum sound numbering sequence, the number of MIDI
channels that can be used, and other general factors that
determine the sound source configuration. Because of this,
musical data produced on a General MIDI sound source can
be played back using similar tones and identical nuances as
the original, even when played on another manufacturer’s
sound source.
This piano conforms to General MIDI standards, so it can be
connected to a computer or other device and used to play
back General MIDI data that has been purchased,
downloaded from the Internet, or obtained from any other
source.
426-E-068A
PL40NE01-1.book
67 ページ
2002年7月23日 火曜日 午後6時52分
Using MIDI
Sending and Receiving MIDI
Messages
This piano can send notes you play on the keyboard, as well
as auto accompaniment patterns and sequencer playback as
MIDI messages to another device.
MIDI Message Receive
J Multi Channel Receive
The 16 external parts can be used to receive data over 16 MIDI
message channels at the same time. Receive channel
assignments for each part can be made using the “MIDI
Receive Channel” parameter (page E-80).
J Chord Changes when Using Auto Accompaniment
MIDI Send Data
J Keyboard Play
Each keyboard part (Upper1, Upper2, Lower1, Lower2) can
be sent over its own individual MIDI channel. When auto
harmonize is turned on, harmonize notes are also sent over
each individual MIDI channel.
MIDI messages received from an external device can be
interpreted as chord changes as specified by the fingerings
supported by the auto accompaniment system of this piano.
Use the “MIDI In Chord Judge” parameter (page E-79) to turn
this capability on and off.
Š See the MIDI Implementation Chart at the back of this
User’s Guide for more information about each MIDI
message.
J Auto Accompaniment Play
Each accompaniment part can be sent over its own individual
MIDI channel. The “Accomp MIDI Out” parameter (page
E-79) is used to specify whether a part is sent.
J Sequencer Playback
The following describes how track data can be sent over
individual MIDI channels.
Š System Track
Each part (Group A) that makes up the system track can
be sent over its own individual MIDI channel.
Š Tracks 1 through 16
Tracks 1 through 16 correspond to Group B parts 1
through 16. Each part can be sent over its own individual
MIDI channel.
J Part Send Channels
Use the procedure on page E-71 and the information on page
E-79 to assign a send channel for each part.
426-E-069A
E-67
PL40NE01-1.book
68 ページ
2002年7月23日 火曜日 午後6時52分
Using MIDI
MIDI Settings
You can change the settings of a number of parameters that control how MIDI messages are sent and received.
MIDI Parameters
You can use the keyboard settings procedure (page E-71) to change the settings of the MIDI parameters described in the table below.
See page E-72 for details about the setting procedure. The reference pages in the table show where you should go for more
information about each parameter.
Setting/Menu
Description
Reference Page
Navigate Channel
(Navi. Ch)
Specifies the MIDI channel whose Note On message data lights the
keyboard keys.
E-79
Accomp MIDI Out
(Accomp MidiOut)
Specifies whether this piano’s accompaniment is sent as MIDI
messages.
E-79
MIDI In Chord Judge
(MidiIn ChordJdg)
Specifies whether MIDI messages received from an external device
should be interpreted as auto accompaniment chord changes.
E-79
Real Time Message Out
(RealTim Message)
Specifies whether real-time messages (FA, FC, F8) should be output.
Device ID
Specifies the MIDI device ID for this piano.
E-79
Local Control
Specifies whether or not this keyboard should sound each part in
accordance with the piano’s local control* settings. MIDI send/receive
is performed regardless of local settings.
E-79
MIDI Transmit Channel
(MIDI Tx Ch)
Specifies whether MIDI messages are sent for each part of this piano,
and the send channel for each part.
E-79
MIDI Receive Channel
(MIDI Rx Ch)
Specifies whether MIDI messages are received for each part of this
piano, and the receive channel for each part.
E-80
E-79
* The term “local control” as used here refers to keyboard play, playback of song data, and other control operations and functions
setting of this piano.
J MIDI In Chord Judge
J Accomp MIDI Out (Accompaniment MIDI Out)
This parameter determines whether note data received from
an external device should be interpreted as an auto
accompaniment chord fingering. Turn on this parameter
when you want to control auto accompaniment chords from
a computer or other external device.
Turn on this parameter when you want sound auto
accompaniment on an external devices sound source.
Š On
Causes note data input through MIDI IN to be interpreted
as auto accompaniment chord fingerings. Note data
received over the channel specified as Part 1 by the
receive channel setting parameter described on page E-80
is interpreted as auto accompaniment chord fingerings.
Š On
Outputs auto accompaniment as MIDI messages through
the piano’s MIDI OUT terminal.
Š Off
Does not output auto accompaniment.
Š Off
Turns off “MIDI In Chord Judge”.
E-68
426-E-070A
PL40NE01-1.book
69 ページ
2002年7月23日 火曜日 午後6時52分
Using MIDI
J Device ID
A device ID is a number used by system exclusive messages
to tell one device from another. When you specify a device ID
for this piano, it recognizes (receives) only system exclusive
messages that include the same device ID number.
You should assign device IDs when you are using an external
synthesizer to control multiple PL-40R units. Doing so makes
it possible to send a system exclusive message to a specific PL40R unit.
Connecting to a Computer
You can use the digital piano’s USB terminal to connect to a
computer.
Using the USB Port
Note that you need to purchase a commercially available USB
cable to connect the digital piano to a computer using the USB
port. Once you establish a USB connection between the digital
piano and a computer, you can exchange data between them.
To connect to a computer using the USB
port
1.
On the computer to which you plan to connect,
install the USB driver that comes on the CDROM that comes bundled with the digital piano.
Š For information about installing the driver,
navigate to one of the language directories
located in the root directory of the bundled “PL40R USB Manual and Driver CD-ROM”, and read
the contents of the “readme.txt” file.
2.
426-E-071A
1
2
3
4
Computer USB port
USB cable
USB connector
Digital piano USB port
USB Mode and MIDI Mode
Your digital piano has two data communication modes: a
USB Mode and a MIDI Mode.
The MIDI Mode is used when sending and receiving data
over the PL-40R’s MIDI terminals.
The USB Mode is used when sending and receiving data over
the PL-40R’s USB port. In the USB Mode, the digital piano’s
MIDI IN/OUT terminals can be used for MIDI transfer of data
from a computer. They cannot be used to send data from the
digital piano.
Š The MIDI (USB) function is disabled during demo tune
play, in the Music Library Mode (while Music Library
Mode lamp is lit), and while the keyboard is lit due to
Demo2 (power on alert) operation.
Use a commercially available USB cable to
connect the digital piano to the computer.
E-69
PL40NE01-1.book
70 ページ
2002年7月23日 火曜日 午後6時52分
Using MIDI
USB Mode/MIDI Mode Switching
The digital piano enters the USB mode automatically
whenever a connection is established between the digital
piano and the USB driver running on a connected computer.
Any other time (when there is no USB connection between the
digital piano and a computer), the digital piano is in the MIDI
Mode.
USB Mode
Obtaining USB Driver
Upgrades and the Latest
PL-40R Information
J CASIO MUSIC SITE
The CASIO MUSIC SITE is an Internet site where you can
download the most update version of the USB driver, and
find out the latest news and important announcements about
the PL-40R. It is recommended that you occasionally visit the
CASIO MUSIC SITE to keep up to date about the PL-40R.
∗ CASIO MUSIC SITE
http://music.casio.com/
MIDI Mode
Š If you connect to a computer via the USB port before
turning on power, the initial screen displays “USB” for
about one second when you turn on power.
1.
2.
3.
Go to the above URL.
Select a region or country.
Select the PL-40R service you want.
Š Note that the service you should use depends on
the area or country.
Š The “USB” indicator appears for about one second to
indicate the USB Mode whenever you connect to a
computer via the USB port.
Š “MIDI” is displayed for about one second to indicate the
MIDI Mode whenever you disconnect the USB cable from
the digital piano.
E-70
426-E-072A
PL40NE01-1.book
71 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Keyboard Settings
1
4
Selector dial
FUNCTION
2
5
[
]/[
]
3
6
[+]/[–]
ENTER/YES
EXIT/NO
This section provides details of all the settings you can make on this piano.
Using the Keyboard Setup Menus
Setting Types
The table below shows the parameters whose settings you can change.
Setting/Menu
Description
Page
Tune
Fine adjustment of overall piano tuning
Sound
Brilliance and equalizer settings
E-75
Lesson
Specifies settings related to Music Library play and lessons.
E-75
General
Touch response, metronome volume, memory back up, and other
general settings
E-76
Display
Display brightness, language, etc.
E-76
Pedal
Assignment of effects to pedals, and effect settings
E-77
Accomp
Settings for auto accompaniment
E-78
MIDI
MIDI settings
E-79
MIDI Transmit Channel
(MIDI Tx Ch)
MIDI send channel setting
MIDI Receive Channel
(MIDI Rx Ch)
MIDI receive channel setting
System
Piano master volume, effect adjustments, etc.
E-80
Initialize
Reset operations to initialize all settings to initial factory defaults or to
reset specific settings
E-81
426-E-073A
E-31, 73
E-79
E-80
E-71
PL40NE01-1.book
72 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
To use the keyboard setup menus
1.
2.
3.
4.
Press the FUNCTION button.
While a main menu screen is on the display, use the [
whose settings you want to configure.
] and [
] buttons to display the main menu item
Press ENTER/YES to display the sub menu of the displayed main menu item.
Use the [
] and [
] buttons to display the sub menu item you want.
Keyboard Settings Main Menus and Sub Menus
Text inside the boxes above show what appears on the digital piano’s display.
E-72
426-E-074A
PL40NE01-1.book
73 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
5.
Use [+] and [–] or the selector dial to change the setting.
Š Settings you make are applied even if you do not press the ENTER/YES button.
Š Pressing [+] and [–] at the same time returns the display value to its initial default.
Š See the following section titled “Parameter Setting Items” for details on each setting.
6.
After making the settings you want, press the FUNCTION button or EXIT/NO button to clear the setting screen.
Parameter Setting Items
Š See the “Parameter List” at the back of this manual for initial default settings (page A-17).
Setting: Tune
Main Menu
Tune
Sub Menu
Settings
Description
Master Tune
(Master)
415.3 Hz ~ 466.2 Hz
Specifies the frequency of A4. The initial default setting is
A4=440.0Hz. See “Tuning the Piano” on page E-31 for
more information.
Baroque Pitch
(Baroque)
On (A4=415.3Hz),
Off
Turning on Baroque Pitch automatically changes the
tuning of the keyboard to Baroque era standard pitch,
which is about a semitone lower than modern pitch. The
initial default setting is Off.
Stretch Tune
(Stretch)
On, Off
Selecting Off disables the piano tone tuning curve (higher
high range, lower low range). The initial default setting is
On.
The tuning curve is not suitable for classical tuning.
Specifying classical tuning as the temperament type
causes the Stretch Tune setting to return to Off
automatically. Even when Stretch Tune is turned on, the
tuning curve is not applied to non-piano tones.
Temperament Type
(Temp Type)
426-E-075A
Besides the normally used Equal Temperament, you can
select from among six other classical temperaments. The
initial default setting is Equal Temperament (Equal).
Equal Temperament
(Equal)
The octave is divided into 12 equal parts and assigned to
white and black keys. This is the tuning normally used for
today’s keyboard musical instruments.
Just Major
Intonation (JustMaj)
Historically, this temperament came into being with the
development of triads. Within a single tonality (major
key), essential major triads produce perfectly
harmonious, beautiful sound. Just Major Intonation also,
however, includes dissonant intervals, and its weakness
is a lack of modulation freedom, etc.
E-73
PL40NE01-1.book
74 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Main Menu
Sub Menu
Temperament Root
(Temp Root)
E-74
Settings
Description
Just Minor
Intonation (JustMin)
This temperament arranges just major intonation to
provide perfect harmony within a single tonality (minor
key). Within the 12 notes, 11 of the notes are the same
pitch as just major intonation.
Pythagorean System
(Pythago)
This temperament, which uses a 12-note octave, is
thought to be the oldest. Of the 12 types of perfect fifths
that can be played, 11 are in perfect harmony. Thirds are
unharmonious and dissonant, and are appropriate for
melody play.
Mean – Tone System
(Mean)
This highly practical temperament provides many of the
merits (beautiful triads) of just intonation, plus
modulation capabilities. It was used as a keyboard tuning
method for a long period following the Renaissance.
Werckmeister
(Werck)
This is a kind of unequal temperament that allows play of
all tonality. It is believed that Bach’s “The Well-Tempered
Clavier” was written using this temperament. Using a
root of C makes the dominant tonality of the white keys
close to mean-tone, and the dominant tonality of the
black keys close to Pythagorean System.
Kirnberger (Kirnber)
This is also a type of unequal temperament, which is also
similar to the Werckmeister tuning described above. The
chromatic differential of the white key dominant tonality
and black key dominant tonality is more pronounced.
#
b
#
C, C , D, E , E, F, F ,
b
b
G, A , A, B , B
Specifies the root of a temperament. The initial default
setting is C. Selecting a different root for equal
temperament does not make a difference in the sound,
but a difference can be noted with classical
temperaments. For classical temperaments other than
Werckmeister and Kirnberger, specify the tonality
keynote of the piece you are playing when using a
classical temperament.
426-E-076A
PL40NE01-1.book
75 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: Sound
Main Menu
Sound
Sub Menu
Settings
Description
Brilliance
–12 to 0 to 12
Controls the brilliance of the tone. A negative value
produces a softer are tone, while a positive value
produces a harder tone.
Equalizer : Speaker
1, 2, 3
Adjusts speaker sound quality in accordance with the
location of the speakers. This setting is not applied to
headphone output.
1 : Bright sound
Recommened when the digital piano is located away
from walls, in front of a curtain, etc.
2 : Normal sound
Recommended when the digital piano is located in front
of a covered wall or other surface that absorbs sound, and
when the audience is located in back of the digital piano.
3 : Soft sound
Recommened when the digital piano is located in front of
a wall or other hard surface that reflects sound.
Setting: Lesson
Main Menu
Lesson
426-E-077A
Sub Menu
Settings
Description
Speak
English (Eng),
Japanese (Jpn), Off
Controls voice fingering guide.
Repeat
On, Off
Turns loop play on and off.
Pre Count
On, Off
Switches the count that sounds before accompaniments
or lessons on and off.
E-75
PL40NE01-1.book
76 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: General
Main Menu
General
Sub Menu
Touch
Settings
Description
Light
Relatively light touch
Normal
Normal touch response
Heavy
Relatively heavy touch required to increase sound
volume.
Off
Touch response off. Sound output not affected by
pressure applied to the keyboard.
Metronome Volume
(MetroVol)
000 to 127
Specifies metronome volume. Also controls voice
fingering guide volume.
Memory Back Up
(Back Up)
On, Off
Specifies whether settings should be backed up when the
piano is turned off. See the “Parameter List” at the back
of this manual for information about what items are
backed up (page A-17).
Demo 2
On, Off
Turns the power on alert feature on and off.
Setting: Display
Main Menu
Display
E-76
Sub Menu
Settings
Description
Contrast
0 to 127
Adjusts screen brightness.
Display Hold (Hold)
On, Off
Turning on this item leaves the current screen on the
display without auto return to the main display.
Language
English (Eng),
Japanese (Jpn)
Specifies Japanese or English as the display language.
426-E-078A
PL40NE01-1.book
77 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: Pedal
Main Menu
Pedal
Sub Menu
Assign Left
(Assign L)
Sustain Length
(Sus Length)
426-E-079A
Settings
Description
Specifies the function of the pedal connected to the SOFT/SOSTENUTO jack.
Soft
Soft pedal
Sostenuto
Sostenuto pedal
Fill-In
Pedal performs same function as the FILL-IN button.
Break
Pedal performs same function as the BREAK button.
Synchro
Pedal performs same function as the SYNCHRO START/
STOP button.
Auto Harmonize
(AutoHarmo)
Pedal applies “Auto Harmonize”.
On Bass Chord
(OnBassChord)
Pedal toggles on bass on and off. See page E-78 for more
information about “On Bass Chord”.
Chord Judge
Available
(ChordJudge)
Makes chord judge available in the FULL RANGE
CHORD mode, only while the pedal is depressed.
This feature makes it possible to momentarily turn FULL
RANGE CHORD on and off as required.
DSP
Pedal toggles DSP on and off.
1 to 63, Hold
This setting specifies how long the volume of the sound
is sustained while the damper pedal is depressed. Hold is
the maximum sustain time, and with an organ type tone
the sound continues as long as the damper pedal is
depressed. A value specifies the sustain time, with
sustain being maintained longer as the value becomes
greater.
E-77
PL40NE01-1.book
78 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: Accomp
Main Menu
Accomp
Sub Menu
Settings
Description
Chord Hold
(Hold Chord)
On, Off
Specifies whether auto accompaniment chords should
continue to play after the keys in the accompaniment
keyboard range are released. On causes auto
accompaniment chords to continue, while Off causes
chords to stop, but rhythm continues.
Lower Hold
(Hold Lower)
On, Off
Specifies whether the lower parts (Lower1, Lower2)
should continue (On) to play or stop (Off) during auto
accompaniment after keys are released. On adds more
depth to accompaniments.
Mixer Hold
(Hold Mixer)
On, Off
Specifies whether accompaniment part mixer settings
should be retained. Off causes settings assigned to each
rhythm to be applied each time a rhythm is selected. On
saves mixer settings to be retained, even when you
change to another rhythm.*1
On Bass Chord
(Chord OnBass)
On, Off
Specifies whether the lowest note you play when using
an inverted fingering of a chord in the accompaniment
keyboard range during auto accompaniment should be
interpreted as a bass note. On causes the lowest note of an
inverted form chord to be interpreted as a bass note,
while Off causes the inverted form chord to sound
normally.*2
Tension Chord
(Chord Tension)
On, Off
Enables and disables recognition of tension chords
during auto accompaniment play. On enables
recognition, while Off disables recognition.
6th Chord
(Chord 6th)
On, Off
Enables and disables recognition of 6th and m6th
fingerings during auto accompaniment play. On enables
recognition, while Off disables recognition.*3
*1. Rhythm elements are preset with optimum default mixer settings, which are normally applied automatically when you use
auto accompaniment. Turning on “Mixer Hold” uses your settings instead of the preset defaults.
*2. This setting is mainly used with the FINGERED auto accompaniment mode, and it helps to turn it on when you want to play
“on bass chords” within the relatively limited accompaniment keyboard range. You can leave this setting off if you are playing
both the bass note and the other notes of the chord in the accompaniment keyboard range. Even when “On Bass Chord” is
turned off, a chord in the accompaniment keyboard range with a fingering that separates the lowest note and the next lowest
note by five tones or more is always interpreted as an “on bass chord” whose root is the lowest note.
*3. Examples
Off: Interpreted as Am7
On: Interpreted as C6
E-78
426-E-080A
PL40NE01-1.book
79 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: MIDI
Main Menu
MIDI
MIDI Transmit
Channel
(MIDI Tx Ch)
Group A
426-E-081A
Sub Menu
Settings
Description
Navigate Channel R
(Navi. Ch R PART)
1 to 16, Off
Specifies the MIDI channel whose Note On message data
lights keyboard keys for the right hand part.
Navigate Channel L
(Navi. Ch L PART)
1 to 16, Off
Specifies the MIDI channel whose Note On message data
lights keyboard keys for the left hand part.
Accomp MIDI Out
(Accomp MidiOut)
On, Off
Specifies whether this piano’s accompaniment is sent as
MIDI messages.*
MIDI In Chord
Judge
(MidiIn ChordJdg)
On, Off
Specifies whether accompaniment range MIDI Note On
messages received from an external device should be
interpreted as auto accompaniment chords.
Real Time Message
Out
(RealTim Message)
On, Off
Specifies whether real-time messages (FA, FC, F8) should
be output.
Device ID
1 to 32
Specifies the MIDI device ID for this piano.
Local Control
On, Off
Specifies whether or not this piano should sound each
part in accordance with the piano’s local control settings.
Group
A, B, Off
Specifies whether this piano’s Group A part or Group B
part accompaniment should be sent as MIDI channel
messages, or whether neither should be sent. When
Group A is specified, you can specify send channels for
each of the Group A parts (Upper1 to Chord5) noted
below. When Group B is specified, you can specify send
channels for each of the Group B parts (Part1 to 16) noted
below.
Upper1
1 to 16, Off
Upper2
1 to 16, Off
Specifies whether MIDI messages are sent for Group A
parts of this piano, and the send channel for Group A
parts.
Lower1
1 to 16, Off
Lower2
1 to 16, Off
Harmo1
1 to 16, Off
Harmo2
1 to 16, Off
Percussion (Perc.)
1 to 16, Off
Drum
1 to 16, Off
Bass
1 to 16, Off
Chord1
1 to 16, Off
Chord2
1 to 16, Off
Chord3
1 to 16, Off
Chord4
1 to 16, Off
E-79
PL40NE01-1.book
80 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Main Menu
Group B
Sub Menu
Settings
Chord5
1 to 16, Off
Part1
1 to 16, Off
″
∼
Part16
1 to 16, Off
Part1
1 to 16, Off
″
∼
MIDI Receive
Channel
(MIDI Rx Ch)
Part16
Description
Specifies whether MIDI messages are received for Group
B parts of this piano, and the receive channel for Group B
parts.
1 to 16, Off
* Whenever you turn on Accomp MIDI Out, the MIDI Tx setting becomes Group A and a message appears asking if you want to
make the settings (initial defaults, etc.) required for each part.
Setting: System
Main Menu
System
E-80
Sub Menu
Settings
Description
DSP Volume
0 to 127
Adjusts the volume of the part to which effect DSP is
being applied. This volume setting is multiplied by the
mixer Volume setting.
DSP Pan
–64 to 63
Adjusts the pan (stereo position) of the part to which
effect DSP is being applied.
DSP Reverb Send
(DSP RevSend)
0 to 127
Adjusts the reverb send of the part to which effect DSP is
being applied. The mixer Mode reverb send setting is
disabled.
DSP Chorus Send
(DSP ChoSend)
0 to 127
Adjusts the chorus send of the part to which effect DSP is
being applied. The mixer Mode chorus send setting is
disabled.
Total Master
Volume
(Total M.Volume)
0 to 127
Adjusts overall piano volume.
Total Master Pan
(Total M.Pan)
–64 to 63
Adjusts overall piano pan (stereo position).
426-E-082A
PL40NE01-1.book
81 ページ
2002年7月23日 火曜日 午後6時52分
Keyboard Settings
Setting: Initialize
Main Menu
Initialize
426-E-083A
Sub Menu
Description
Group B
Initializes Group B parts when MIDI IN is used.
Parameter All
Returns all parameters to their initial default settings.
All
Returns the piano to its initial factory defaults. Deletes all data, including
sequencer data.
E-81
PL40NE01-1.book
82 ページ
2002年7月23日 火曜日 午後6時52分
426-E-084A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement