EC Declaration of Conformity EC Declaration of

EC Declaration of Conformity EC Declaration of
EC Declaration of Conformity
EC Declaration of Conformity
According to
Low Voltage Directive 2006/95/EC
Report No:
Type of equipment:
Model Name:
Applicant:
Address:
Manufacturer:
Address:
Test Standards:
10EMC-CE-S004
CAMERA HOUSING
SHB-4300H2
SAMSUNG TECHWIN CO., LTD.
28, Seongju-Dong, Changwon-City,
Gyeongsangnam-Do, Korea (641-716)
NINGBO KEVIS INC
#10-5 Laoshanlu, Dagang IND Zone,
Beilun, Ningbo, Zhejiang, China
EN 60065: 2002
*The standards relevant for the evaluation of LVD requirements are as follows.
Complies with the essential requirements of Low Voltage Directive 2006/95/EC and
CE-Marking accordingly. This declaration applies to all specimens manufactured in
accordance with manufacturer’s technical manufacturing drawings.
Assessment of compliance of the product with the requirements relating electronics
safety was based on the harmonized standards.
Date of issue: February 17, 2010
SAMSUNG TECHWIN CO., LTD.
28, Seongju-Dong, Changwon-City,
Gyeongsangnam-Do, Korea (641-716)
---------------------------------------------------------(Name and signature of authorized person)
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
SAFETY TEST REPORT
EN 60065:2002
Audio, Video and similar apparatus Safety requirements
Report No.
10EMC- CE- S004
Type of equipment
CAMERA HOUSING
Applicant
(Name/Address)
SAMSUNG TECHWIN CO., LTD.
28, Seongju-Dong, Changwon-City,
Gyeongsangnam-Do, Korea (641-716)
Trade mark
Manufacturer
(Name/Address)
NINGBO KEVIS INC.
#10-5 Laoshanlu, Dagang IND Zone,
Beilun, Ningbo, Zhejiang, China
Model No.
SHB-4300H2
Electrical Ratings
AC 230 V~, 50 Hz, 55 W, Class I
The equipment complies with the principal protection requirements of Low Voltage Directive
(Directive 2006/95/EEC relating to electrical equipment designed for ues within certain voltage limits)
based on a voluntary test. This report applied only to the particular sample of the product provided for
testing. Also this test report shall not be reproduced except in full, without the written approval of
EMC compliance Laboratory.
This test result carried out from a sample of the submitted type in conformity with
the specification of the respective standards.
This test report is not permitted to be duplicated in extracts. This test report does not entitle to
carry any test mark on this or similar products.
EMC compliance Ltd.
Page: 1 of 26
82-1 Jeil-ri, Yangji-myun, Churingu, Yongin-city, Kyungki-do,Korea 449-825,
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
TEST REPORT
IEC/EN 60065
Audio, video and similar electronic apparatus
Safety requirements
Report Reference No. ....................... : 10EMC-CE-S004
Tested by (+ signature) ...................... : Surk-Chan, Yun
.......................................................
Approved by (+ signature) ................. : Jae-Kyu, Lee
.......................................................
Date of issue ...................................... : 2010-02-17
Testing laboratory Name ................. : EMC COMPLIANCE LTD.
Address .............................................. : 480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,
443-390, Korea.
Applicant’s Name ............................ : SAMSUNG TECHWIN CO., LTD.
Address .............................................. : 28, Seongju-Dong, Changwon-City, Gyeongsangnam-Do,
Korea (641-716)
Standard ............................................. : EN 60065:2002, 7th Edition
Test procedure .................................. : CCA-Scheme
Non-standard test method ................. : N.A.
Test Report Form/blank test report
Test Report Form No. ........................ : REPORT.DOT
TRF originator. ................................... : Master TRF ........................................ : Copyright @ 2003 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE),
Geneva, Switzerland. All rights reserved.
This publication may be produced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright
owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader’s
interpretation of the reproduced material due to its placement and context
Test item Description ...................... : CAMERA HOUSING
Trademark .......................................... :
Model and/or type reference.............. : SHB-4300H2
Manufacturer ...................................... : NINGBO KEVIS INC
Rating(s) ............................................. : 230 V~, 50 Hz, 55 W
EMC compliance Ltd.
Page: 2 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Test case verdicts
Test case does not apply to the test object .................. : N(.A.)
Test item does meet the requirement .......................... : P(ass)
Test item does not meet the requirement .................... : F(ail)
Testing
Date of receipt of test item ........................................... : 2010-02-05
Date(s) of performance of test ...................................... : 2010-02-08 until 2010-02-12
General remarks
This report shall not be reproduced except in full without the written approval of the testing laboratory.
The test results presented in this report relate only to the item(s) tested.
"(see appended table)" refers to a table appended to the report.
“(see remark #)” refers to a remark appended to the report.
“(see Annex #) refers to an annex appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
Summary of Testing and Conclusions
The sample(s) tested complies with the requirements of IEC/EN 60065:2002. Compliance with European
Special National Conditions, Annex ZB, and A – Deviations, Annex ZC, is recorded at the end of this report.
General product information:
-
The following contents that are included in this test report are
Test report : 26 pages
Attachment 1 : 3 pages (Photograph)
EMC compliance Ltd.
Page: 3 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Copy of marking plate
EMC compliance Ltd.
Page: 4 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
3
GENERAL REQUIREMENTS
Result - Remark
Verdict
Safety class of the apparatus ................................. :
4
GENERAL CONDITIONS OF TESTS
4.1.4
Ventilation instructions require the use of the test
box .......................................................................... :
5
MARKING
5.1
P
N/A
Comprehensible and easily discernible
On the side of the enclosure,
The marking is easily
Comprehensible and easily
discernible when ready for use
P
Permanent durability against water and petroleum
spirit
The marking is not removed
when rubbed lightly with a
piece of cloth soaked with
petroleum spirit or water
P
Identification, maker, model ................................... :
P
, SHB-4300H2
Class II symbol if applicable
5.2
No Class II equipment
N/A
Rated supply voltage and symbol .......................... : 230 V~
P
Frequency if safety dependant
50 Hz
P
Rated current or power consumption .................... : 55 W
P
Earth terminal
P
Bottom steel
Hazardous live terminals
N/A
Supply output terminals (other than mains)
N/A
5.3
Use of triangle with exclamation mark
In circuit diagram
P
5.4
Instructions for use
English
P
5.4.1
Mains powered equipment not exposed to dripping
or splashing. Warning concerning objects filled
with liquid, etc.
N/A
Hazardous live terminals, instructions for wiring
N/A
Instructions for replacing lithium battery
No lithium battery
N/A
Instructions for modem if fitted
Class I earth connection warning
N/A
In user manual
P
Instructions for multimedia system connection
N/A
Special stability warning for fixed installation
P
N/A
Warning: battery exposure to heat
EMC compliance Ltd.
Page: 5 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
N/A
Warning: protective film on CRT face
5.4.2
Disconnect device: plug/coupler or all-pole mains
switch location, accessibility and markings
P
Instructions for permanently connected equipment
N/A
6
HAZARDOUS RADIATION
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
No Ionizing radiation
N/A
6.1
European Council Directive 96/29/Euratom of 13
May 1996 10cm from outer surface of apparatus
<1µSv/h (0,1mR/h)
No laser
N/A
EN 60065
6.2
Laser radiation, emission limits to IEC 60825-1 .... :
N/A
Emission limits under fault conditions .................... :
N/A
7
HEATING UNDER NORMAL OPERATING CONDITIONS
7.1
Temperature rises not exceeding specified values, (see appended table)
no operation of fuse links
P
7.1.1
Temperature rise of accessible parts
(see appended table)
P
7.1.2
Temperature rise of parts providing electrical
insulation
(see appended table)
P
7.1.3
Temperature rise of parts acting as a support or as
a mechanical barrier
7.1.4
Temperature rise of windings
(see appended table)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
(see appended table)
P
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150 oC
(see appended table)
N/A
8
CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION
AGAINST ELECTRIC SHOCK
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
Considered
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
No change of voltage setting or
fuse by hand.
N/A
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
No hygroscopic material used
N/A
8.4
No risk of electric shock following the removal of a
cover which can be removed by hand
No removal of cover by hand
N/A
8.5
Class I equipment
P
Basic insulation between hazardous live parts and
earthed accessible parts
P
EMC compliance Ltd.
N/A
P
Page: 6 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
Resistors bridging basic insulation complying with
14.2.1 a)
8.6
8.7
8.8
Class II equipment and Class II constructions
within Class I equipment
Class I
N/A
Reinforced or double insulation between
hazardous live parts and accessible parts
N/A
Components bridging reinforced or double
insulation complying with 14.1 a) or 14.3
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.2.1 a)
N/A
Reinforced or double insulation being bridged with
2 capacitors in series complying with 14.2.1 a)
N/A
Reinforced or double insulation being bridged with
a single capacitor complying with 14.2.1 b)
N/A
Basic insulation bridged by components complying
with 14.3.4.3
N/A
Basic insulation between parts at 35 V to 71 V
(peak) a.c. or 60 V to 120 V d.c. and accessible
parts
N/A
Reinforced or double insulation between circuits
operating at voltages between 35 V and 71 V
(peak) a.c. or between 60 V and 120 V d.c. and
hazardous live parts at higher voltage
N/A
Separation by Class II isolating transformer
N/A
Separation by Class I transformer
N/A
Separation by earthed conductive part
N/A
Basic or supplementary insulation > 0,4 mm (mm) :
P
Reinforced insulation > 0,4 mm (mm) .................... :
P
Thin sheet insulation
8.9
N/A
(see clause 14.3.4.1)
N/A
Basic or supplementary insulation, at least two
layers, each meeting 10.3
N/A
Basic or supplementary insulation, three layers any
two of which meet 10.3
N/A
Reinforced insulation, two layers each of which
meet 10.3
N/A
Reinforced insulation, three layers any two which
meet 10.3
N/A
Adequate insulation between internal hazardous
live conductors and accessible parts
Provided double or reinforce
insulation
P
Adequate insulation between internal hazardous
live parts and conductors connected to accessible
parts
Dressed away from live parts
P
EMC compliance Ltd.
Page: 7 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
8.10
Double insulation between conductors connected
to the mains and accessible parts
Result - Remark
Verdict
P
Double insulation between internal hazardous
live parts and conductors connected to
accessible parts.
8.11
Detaching of wires
No undue reduction of creepages or clearance
distances if wires become detached
P
Connectors provided for all
detaching of wires
Vibration test carried out ........................................ : No risk of wire becoming
detached
P
P
8.12
Adequate cross-sectional area of internal wiring to
mains socket-outlets
Not provided mains socketoutlets incorporated in the
apparatus
N/A
8.13
Adequate fastening of windows, lenses, lamp
covers etc. (pull test 20 N for 10 s)
8.14
Adequate fastening of covers (pull test 50 N for
10 s)
No cover subjected to forces
during intended use
N/A
8.15
No risk of damage to the insulation of internal
wiring due to hot parts or sharp edges
No damaged to the insulation
of internal wiring
P
8.16
Only special supply equipment can be used
No special supply equipment
N/A
8.17
Insulated winding wire without additional
interleaved insulation
N/A
8.18
Endurance test as required by 8.17
N/A
8.19
Disconnection from the mains
8.19.1
Disconnect device
P
P
Mains plug
P
All-pole switch or circuit breaker with >3mm
contact separation
N/A
8.19.2
Mains switch ON indication
N/A
8.20
Switch not fitted in the mains cord
No switch in the mains cord
N/A
8.21
Bridging components comply with clause 14
Not provided a components
used for bridging contact gaps
of switches conductively
connected to mains
N/A
8.22
Non-separable thin sheet material
9
ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS
9.1
Testing on the outside
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
9.1.1.1
Touch current measured from terminal devices
Class I construction : 0.02 mA
using the network in annex D ................................. :
EMC compliance Ltd.
No exceeding 1000 Vac or
1500 Vdc
N/A
P
Page: 8 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Discharge not exceeding 45 μC
Not exceedind 60 Vdc
N/A
Energy of discharge not exceeding 350 mJ
Not exceedind 15 kVdc
N/A
9.1.1.2
Test with test finger and test probe
Not touched hazardous live
parts
9.1.2
No hazardous live shafts of knobs, handles or
levers
Not provided
N/A
9.1.3
Ventilation holes and other holes tested by means
of 4 mm x 100 mm test pin
No openings
P
9.1.4
Terminal devices tested with 1 mm x 20 mm test
pin (10 N); test probe D of IEC 61032
No terminal device
N/A
Terminal devices tested with 1 mm x 100 mm
straight wire (1 N); test probe D of IEC 61032
No terminal device
N/A
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test
pin (10 N); test probe C of IEC 61032
No pre-set controls
N/A
9.1.6
No shock hazard due to stored charge on
No ac mains capacitor
withdrawal of the mains plug; voltage (V) after 2 s :
9.1.7
Verdict
P
N/A
If C is not greater than 0,1 μF no test needed
P
Enclosure sufficiently resistant to external force
P
Test probe 11 of IEC 61032 for 10 s (50 N)
The test probe cannot
contacted hazardous live part
P
Test hook of fig. 4 for 10 s (20 N)
The test hook cannot
contacted hazadous live part
P
30 mm diameter test tool for 5 s (100 or 250 N) .... : Applied 100 N
P
9.2
No hazard after removing a cover by hand
No removing a cover by hand
10
INSULATION REQUIREMENTS
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after (see appended table 10.3)
surge test for basic and 4 MΩ min. for reinforced
insulation ................................................................. :
P
10.2
Humidity treatment 48 h or 120 h ........................... : 48 h, 32 oC, 93%
P
10.3
Insulation resistance and dielectric strength
(see appended table)
P
Insulation Resistance and dielectric strength
across BASIC or SUPPLEMENTARY insulation
(Class I)
(see appended table)
P
N/A
Insulation Resistance and dielectric strength
across REINFORCED insulation (Class II)
11
FAULT CONDITIONS
11.1
No shock hazard under fault condition
EMC compliance Ltd.
N/A
No electric shock hazard under
fault conditions.
P
Page: 9 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
Result - Remark
Verdict
11.2
Heating under fault condition
(see appended table)
P
No hazard from softening solder
No softening of solder
P
Flames extinguish within 10 seconds
No flames
P
Soldered terminations not used as protective
mechanism
No soldered terminations
P
11.2.1
Measurement of temperature rises
(see appended table)
P
11.2.2
Temperature rise of accessible parts
(see appended table)
P
11.2.3
Temperature rise of parts, other than windings,
providing electrical insulation
(see appended table)
P
Temperature rise of printed circuit boards (PCB)
exceeding the limits of table 3 by max. 100 K for
max. 5 min
No exceeding the limits of
table 3
N/A
a) Temperature rise of printed circuit boards (PCB)
to 20.1.3, exceeding the limits of table 3 by not
more than 100 K for an area not greater than 2 cm²
N/A
b) Temperature rise of printed circuit boards (PCB)
to 20.1.3 up to 300 K for an area not greater than
2 cm² for a maximum of 5 min
N/A
Meets all the special conditions if conductors on
printed circuit boards are interrupted
N/A
Class I protective earthing maintained
P
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
(see appended table)
N/A
11.2.5
Temperature rise of windings
(see appended table)
N/A
11.2.6
Temperature rise of parts not subject to the limits
of 11.2.1 to 11.2.5
(see appended table)
P
12
MECHANICAL STRENGTH
12.1.1
Bump test where mass >7 kg
Weight: 3.7 kg
12.1.2
Vibration test
No damage
P
12.1.3
Impact hammer test
0.5 J
P
Steel ball test
2J
P
12.1.4
Drop test for portable apparatus where mass < 7
kg
Not portable apparatus
N/A
12.1.5
Thermoplastic enclosures stress relief test
Not provided
N/A
12.2
Fixing of knobs, push buttons, keys and levers
Not provided
N/A
12.3
Remote controls with hazardous live parts
Not provided
N/A
12.4
Drawers (pull test 50 N, 10 s)
Not provided
N/A
12.5
Antenna coaxial sockets providing isolation
Not provided
N/A
EMC compliance Ltd.
N/A
Page: 10 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
Result - Remark
Verdict
12.6
Telescoping or rod antennas construction
Not provided
N/A
12.6.1
Telescoping or rod antennas securement
Not provided
N/A
13
CLEARANCE AND CREEPAGE DISTANCES
13.1
Clearances in accordance with 13.3
Considered
P
Creepage distances in accordance with 13.4
Considered
P
13.2
Determination of operating voltage
Considered
P
13.3
Clearances
-2 N for internal parts
-30 N for external parts
P
13.3.2
Circuits conductively connected to the mains
comply with table 8 and, where applicable, table 9
13.3.3
Circuits not conductively connected to the mains
comply with table 10
N/A
13.3.4
Measurement of transient voltage
N/A
13.4
Creepage distances
P
230 Vrms
P
Creepage distances greater than table 11 minima
P
13.5
Printed boards
N/A
13.5.1
Clearances and creepage distances between
conductors on printed circuit boards, one of which
may be conductively connected to the mains, as in
fig. 10
N/A
13.5.2
Type B coated printed circuit boards complying
with IEC 60664-3 (basic insulation only)
N/A
13.6
Conductive parts along uncemented joints
clearances and creepage distances comply with
13.3 and 13.4
N/A
Conductive parts along reliably cemented joints
comply with 8.8
N/A
Temperature cycle test and dielectric strength test
N/A
13.7
Enclosed, enveloped or hermetically sealed parts:
not conductively connected to the mains:
clearances and creepage distances as in table 12
N/A
13.8
Parts filled with insulating compound, meeting the
requirements of 8.8
N/A
14
COMPONENTS
14.1
Resistors
a) Resistors between hazardous live parts and
accessible metal parts
EMC compliance Ltd.
No such component
N/A
Page: 11 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
14.2
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
b) Resistors, other than between hazardous live
parts and accessible parts
N/A
b) Resistors separately approved .......................... :
N/A
Capacitors and RC units
No such component
N/A
Capacitors separately approved
14.2.1
N/A
Y capacitors tested to IEC 60384-14, 2nd edition .. :
N/A
nd
14.2.2
X capacitors tested to IEC 60384-14, 2 edition .. :
N/A
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 ..................... :
N/A
14.2.5
Capacitors with volume exceeding 1750 mm³,
where short-circuit current exceeds 0,2 A:
compliance with IEC60384-1, 4.38 category B or
better ....................................................................... :
N/A
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1,
4.38 category B or better ........................................ :
N/A
Shielded by a barrier to V-0 or metal ..................... :
N/A
14.3
14.3.1
14.3.2
Inductors and windings
No such component
N/A
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
N/A
Transformers and inductors marked with
manufacturer's name and type .............................. :
N/A
Transformers and inductors separately approved . :
N/A
General
No such component
N/A
Insulation material complies with clause 20.1.4
N/A
14.3.3
Constructional requirements
N/A
14.3.3.1
Clearances and creepage distances comply with
clause 13
N/A
14.3.3.2
Transformers meet the constructional
requirements
N/A
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible parts
(double or reinforced insulation)
N/A
Coil formers and partition walls > 0,4 mm
N/A
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of
14.3.4.2 are met
N/A
14.3.4.3
Separating transformers with at least basic
insulation
N/A
EMC compliance Ltd.
Page: 12 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
14.3.5.1
Class II transformers have adequate insulation
between hazardous live parts and accessible parts
(double or reinforced insulation)
N/A
Coil formers and partition walls > 0,4 mm
N/A
Class I transformers have adequate insulation
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
N/A
Winding wires connected to protective earth have
adequate current-carrying capacity
N/A
High voltage components
N/A
14.3.5.2
14.4
High-voltage components and assemblies:
U > 4 kV (peak) separately approved
Result - Remark
Verdict
No high-voltage components
N/A
Component meets category V-1 of IEC 60707
N/A
14.4.1
High voltage transformers and multipliers tested as
part of the submission
N/A
14.4.2
High voltage assemblies and other parts tested as
part of the submission
N/A
14.5
Protective devices
Protective devices used within their ratings
P
FUSE: T2.0AH 250V
P
External clearances and creepage distances meet Min. 2.5 mm
requirement of clause 13 for the voltage across the
device when opened
14.5.1.1
a) Thermal cut-outs separately approved
P
No such component
N/A
b) Thermal cut-outs tested as part of the
submission
14.5.1.2
a) Thermal links separately approved
N/A
No such component
N/A
b) Thermal links tested as part of the submission
N/A
14.5.1.3
Thermal devices re-settable by soldering
No such component
14.5.2.1
Fuse-links in the mains circuit according to IEC
60127
(see appended table 14)
14.5.2.2
Correct marking of fuse-links adjacent to holder ... : FUSE: T2.0AH 250V
14.5.2.3
Not possible to connect fuses in parallel ............... : No connect fuse in parallel
14.5.2.4
Not possible to touch hazardous live parts when
In service area
replacing fuse-links without the use of a tool ......... :
14.5.3
PTC-S thermistors comply with IEC 60730-1
No PTC-S thermistors
N/A
PTC-S devices (15 W) category V-1 or better
No PTC-S devices
N/A
14.5.4
N/A
P
P
P
Circuit protectors have adequate breaking capacity
and their position is correctly marked
EMC compliance Ltd.
N/A
N/A
Page: 13 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
Result - Remark
14.6
Switches
No switches
14.6.1 a)
Separate testing to IEC 61058 including:
10 000 operations Normal pollution suitability
Resistance to heat and fire level 3 and
Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
N/A
14.6.1 b)
Tested in the apparatus:
N/A
Switch controlling > 0.2A with open contact
voltage > 35 V (peak)/24 V dc complying with
14.6.3, 14.6.4 and V-0 in annex G, G.1.1
N/A
Switch controlling > 0.2A with open contact
voltage < 35 V (peak)/24 V dc complying with
14.6.3 and V-0 in annex G, G.1.1
N/A
Switch controlling < 0.2A with open contact
voltage > 35 V (peak)/24 V dc complying with
14.6.4 and V-0 in annex G, G.1.1
N/A
14.6.2
Switch tested to 14.6.1 b) constructed to IEC
61058-1 subclause 13.1 and has making/breaking
action independent of speed of actuation
N/A
14.6.3
Switch tested to 14.6.1 b) compliant with IEC
61058-1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
N/A
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
N/A
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 60058-1
N/A
Socket outlet current marking correct
N/A
14.7
Safety interlocks
Verdict
N/A
No safety interlocks
N/A
Safety interlocks to 2.8 of IEC 60950
14.8
Voltage setting devices
N/A
No voltage setting devices
Voltage setting device not likely to be changed
accidentally
N/A
N/A
14.9
Motors
14.9.1
Endurance test on motors
N/A
Motor start test
N/A
Dielectric strength test
N/A
14.9.2
Not adversely affected by oil or grease etc.
N/A
14.9.3
Protection against moving parts
EMC compliance Ltd.
AC Fan for CE approved type
use
No moving parts
P
N/A
Page: 14 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
14.9.4
Motors with phase-shifting capacitors, three-phase
motors and series motors meet clause. B.8, B.9
and B.10 of IEC 60950, Annex B
14.10
Batteries
14.10.1
Batteries mounted with no risk of accumulation of
flammable gases
N/A
14.10.2
No possibility of recharging non-rechargeable
batteries
N/A
14.10.3
Recharging currents and times within
manufacturers limits
N/A
Lithium batteries discharge and reverse currents
within the manufacturers limits
N/A
14.10.4
Battery mould stress relief
N/A
14.10.5
Battery drop test
N/A
14.11
Optocouplers
14.12
Result - Remark
Verdict
N/A
No batteries
N/A
No optocouplers
N/A
Optocouplers comply with Cl. 8
N/A
Internal and external dimensions to 13.1. or
alternatively 13.6 (jointed insulation)
N/A
Surge suppression varistors
No surge suppression varistors
Comply with IEC 61051-2
N/A
Not connected between mains and accessible
parts except for earthed parts of permanently
connected apparatus
N/A
Complies with the current pulse, fire hazard and
thermal stress requirements of 14.12
N/A
15
TERMINALS
15.1.1
Mains plug, appliance inlet, interconnection
couplers and mains socket-outlet meet the
appropriate standard
Used an approved plug
Overloading of plugs or appliance inlets
prevented if the apparatus has mains socket
outlets
No socket-outlets
P
N/A
N/A
Overloading of internal wiring prevented if the
apparatus has mains socket outlets
15.1.2
N/A
Connectors for antenna, earth, audio, video or data:
No risk of insertion in mains socket-outlets
No main socket-outlet
N/A
No risk of insertion into audio or video: outlets
marked with the symbol of 5.2
EMC compliance Ltd.
N/A
Page: 15 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
15.1.3
Output terminals of a.c. adaptors or similar devices No such output terminal
not compatible with household mains socketoutlets
15.2
Provision for protective earthing
Accessible conductive parts of Class I equipment
reliably connected to earth terminal, within
equipment
Result - Remark
Verdict
N/A
Fixed by a screw with washer
N/A
Class I supply equipment with non-hazardous live
output voltage: output circuit not connected to
earth
Protective earth conductors correctly coloured
Green/Yellow wire used
P
P
Equipment with non-detachable mains cord
provided with separate protective earth terminal
near mains input
Protective earth terminal resistant to corrosion
P
No risk of corrosion
P
Earth resistance test: < 0,1 Ω at 25 A ................... : 0.019
P
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
N/A
15.3.1
Adequate terminals for connection of permanent
wiring
N/A
15.3.2
Reliable connection of non-detachable cords:
P
Not soldered to conductors of a printed circuit
board
P
Adequate clearances and creepage distances
between connections should a wire break away
P
Wire secured by additional means to the conductor
P
15.3.3
Screws and nuts clamping conductors have
adequate threads: ISO 261, ISO 262 or similar
P
15.3.4
Soldered conductors wrapped around terminal
prior to soldering or held in place by additional
means
N/A
Clamping of conductor and insulation if not
soldered or held by screws
N/A
15.3.5
Terminals allow connection of appropriate crosssectional area of conductors, for the rated current
of the equipment
0.75 mm2
P
15.3.6
Terminals to 15.3.3 have sizes required by
table 16
3.0 mm
P
15.3.7
Terminals clamp conductors between metal and
have adequate pressure
P
Terminals designed to avoid conductor slipping out
when tightened or loosened
P
EMC compliance Ltd.
Page: 16 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
Terminals adequately fixed to avoid loosening
when the clamping is tightened or loosened and
stress on internal wiring is avoided
P
15.3.8
Terminals carrying a current more than 0,2 A:
contact pressure not transmitted by insulating
material except ceramic
P
15.3.9
Termination of non-detachable cords: wires
terminated near to each other
P
Terminals located and shielded: test with 8 mm
strand
P
15.4
Devices forming a part of the mains plug
N/A
15.4.1
No undue strain on mains socket-outlets
15.4.2
Device complies with standard for dimensions of
mains plugs
N/A
15.4.3
Device has adequate mechanical strength (tests
a,b,c)
N/A
16
EXTERNAL FLEXIBLE CORDS
16.1
Mains cords sheathed type, complying with
(see appended table 14)
IEC 60227 for PVC or IEC 60245 for synthetic
rubber cords ............................................................ :
P
Non-detachable cords for Class I have
green/yellow core for protective earth
P
16.2
Mains cords conductors have adequate cross0.75 mm2
sectional area for rated current consumption of the
equipment
P
16.3
a) Flexible cords not complying with 16.1, used for
interconnections between separate units of
equipment used in combination and carrying
hazardous live voltages, have adequate dielectric
strength
No devices forming a part of
the mains plug
No interconnection cords
N/A
N/A
b) Flexible cords not complying with 16.1,
withstand bending and mechanical stress (3.2 of
IEC 60227-2)
N/A
16.4
Flexible cords used for connection between
No interconnection cords
equipment have adequate cross-sectional areas to
avoid temperature rise under normal and fault
conditions
N/A
16.5
Adequate strain relief on external flexible cords
P
Not possible to push cord back into equipment
P
Strain relief device unlikely to damage flexible cord
P
EMC compliance Ltd.
Page: 17 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
For mains cords of Class I equipment, hazardous
live conductors become taut before earth
conductor
P
16.6
Apertures for external flexible cord: no risk of
damage to the cord during assembly or movement
in use
P
16.7
Transportable musical instruments and amplifiers
fitted with detachable cord set with appliance inlet
to IEC 60320-1
N/A
Transportable musical instruments and amplifiers
fitted with detachable cord sets or with means of
stowage to protect the cord
N/A
17
ELECTRICAL CONNECTIONS AND MECHANICAL FIXINGS
17.1
Torque test to table 20:
- screws into metal: 5 times
P
Screw fixing the metallic
enclosure
P
- screws into non-metallic material: 10 times
N/A
17.2
Correct introduction into female threads in nonmetallic material
N/A
17.3
Cover fixing screws: captive
No captive screws
Non-captive fixing screws: no hazard when
replaced by a screw whose length is 10 times its
diameter
The distance was not less than
those in cl.13
N/A
P
17.4
No loosening of conductive parts carrying a current Secured by connector
> 0,2 A
P
17.5
Contact pressure not transmitted through plastic
other than ceramic for connections carrying a
current > 0,2 A
P
17.6
Stranded conductors of flexible supply cords
carrying a current > 0,2 A with screw terminals not
consolidated by solder
N/A
17.7
Cover fixing devices other than screws have
adequate strength and their positioning is
unambiguous
N/A
17.8
Fixing devices for detachable legs or stands
provided
P
17.9
Internal pluggable connections, affecting safety,
unlikely to become disconnected
18
MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST
THE EFFECTS OF IMPLOSION
Picture tube separately approved to IEC 61965:
EMC compliance Ltd.
Not transmitted through
insulating material
N/A
No picture tube.
N/A
Page: 18 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
Picture tube separately approved to 18.1 ...............
N/A
Picture tubes > 16 cm intrinsically protected
N/A
Non-intrinsically protected tubes > 16 cm used with
protective screen
N/A
Protective film as part of implosion protection:
edges covered by enclosure
N/A
18.2
Intrinsically protected tubes: tests on 12 samples
N/A
18.2.1
Samples subject to ageing: 6
N/A
18.2.2
Samples subject to implosion test: 6
N/A
18.2.3
Samples subject to mechanical strength test (steel
ball): 6
N/A
18.3
Non-intrinsically protected tubes tested to 18.3
N/A
19
STABILITY AND MECHANICAL HAZARDS
18.1
Mass of the equipment exceeding 7 kg ................. : Mass : 3. 7 kg
N/A
Apparatus intended to be fastened in place –
suitable instructions
P
19.1
Test on a plane, inclined at 10o to the horizontal
N/A
19.2
100 N force applied vertically downwards
N/A
19.3
Apparatus mass > 25 kg or height > 1 M or
supplied with cart or stand
No exceeding 25 kg
19.4
Edges or corners not hazardous
Not hazardous
P
19.5
Glass surfaces with an area exceeding 0,1 m² or
maximum dimension > 450 mm, pass the test of
19.5.1
No large glass
N/A
19.6
Wall or ceiling mountings adequate
Load; 11.1 kg
P
20
RESISTANCE TO FIRE
20.1
Electrical components and mechanical parts
N/A
a) Exemption for components contained in an
enclosure of material V-0 to IEC 60695-11-10 with
openings not exceeding 1 mm in width
N/A
b) Exemption for small components as defined in
20.1
P
20.1.1
Electrical components meet the requirements of
Clause 14 or 20.1.4
20.1.2
Insulation of internal wiring working at voltages
Insulation of wiring is PVC and
> 4 Kv or leaving an internal fire enclosure, or
4 kV no high voltage exceeding
located within the areas mentioned in Table 21,
not contributing to the spread of fire
EMC compliance Ltd.
Meet the requirements of
20.1.4
P
N/A
Page: 19 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
Result - Remark
20.1.3
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c. meets
V-1 or better to IEC60707, unless used in a fire
enclosure
Used the rated minimum
V-0 PCB
Verdict
P
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage >400 V
(peak) a.c. or d.c. meets V-0 to IEC 60707
20.1.4
Components and parts not covered by 20.1.1,
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
P
(see appended table 14)
P
Components and parts as above but shielded from No required the barrier
a potential ignition source, with the barrier area in
accordance with Table 21 and fig. 13
N/A
Apparatus with voltage >4kV under normal
operating conditions and distances to the
enclosure exceed those specified Table 21,
flammability classification HB40 or better is
required for the enclosure.
N/A
20.2
Fire enclosure
N/A
20.2.1
Potential ignition sources with open circuit voltage
> 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
< 4 kV
N/A
20.2.2
Internal fire enclosures with openings not
exceeding 1 mm in width and with openings for
wires completely filled
No internal fire enclosure
N/A
20.2.3
Requirements of 20.2.1 and 20.2.2 met by an
internal fire enclosure
No internal fire enclosure
N/A
A
APPENDIX A, ADDITIONAL REQUIREMENTS FOR APPARATUS WITH
PROTECTION AGAINST SPLASHING WATER
A.5.1
j) Marked with IPX4 (IEC 60529), 5.4.1 a) does not IP66
apply
P
A.10.2.1
Enclosure provides protection against splashing
water
P
A.10.2.2
Humidity treatment carried out for 7 days
B
APPENDIX B, APPARATUS TO BE CONNECTED TO THE
TELECOMMUNICATION NETWORKS
Complies with IEC 62151 clause 1
N/A
No TNV circuits.
N/A
Complies with IEC 62151 clause 2
EMC compliance Ltd.
N/A
Page: 20 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
Complies with IEC 62151 clause 3 but with 3.5.4
modified to 2.4.10 of this standard
N/A
Complies with IEC 62151 clause 4 but with 4.1.2,
4.1.3 and 4.2.1.2 modified in accordance with
annex B of this standard
N/A
Complies with IEC 62151 cause 5 but with 5.3.1
modified in accordance with annex B of this
standard
N/A
Complies with IEC 62151 clause 6
N/A
Complies with IEC 62151 clause 7
N/A
Complies with IEC 62151 annex A, B and C
N/A
L
APPENDIX L, ADDITIONAL REQUIREMENTS FOR ELECTRONIC FLASH
APPARATUS FOR PHOTOGRAPHIC
L5.4
Marking and Instructions
L9.1.1
Terminals to connection to synchroniser not
HAZARDOUS LIVE
N/A
L7.1.5 &
L11.2.6
Lithium batteries meet permissible temp rise in
Table 3, unless comply with 6.3.2 of IEC
60086-4
N/A
L14.6.6
Mains switch characteristics appropriate to its
function under normal conditions
N/A
EMC compliance Ltd.
No electronic flash apparatus.
N/A
Page: 21 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
Result - Remark
7.1
TABLE: temperature rise measurements
Verdict
P
Power consumption in the OFF/Stand-by
-
—
Position of the functional switch (W) ...................... :
—
Operating conditions
Un (V)
In (mA)
Pn (W)
Pout (W)
207 V, 50 Hz
39
8.1
-
230 V, 50 Hz
43
10.0
-
253 V, 50 Hz
47
12.1
-
Loudspeaker impedance (Ω) ................................. : No loudspeaker
—
Several loudspeaker systems
-
N/A
Marking of loudspeaker terminals
-
N/A
Monitored point:
dT (K)
Limit dT (K)
207 V 50 Hz
253 V 50 Hz
1. AC lead wire
3.6
5.7
60
2. Fuse holder
3.1
5.1
50
3. AC connector (J1)
3.5
5.8
50
4. AC Fan body
3.6
6.0
40
5. Metal bracket
5.2
7.9
40
6. Front window
13.6
19.1
-
7. Bottom enclosure
3.0
4.7
40
o
8. Ambient
21.6 C
o
21.6 C
-
Winding temperature rise measurements
N/A
Ambient temperature t1 (oC) .................................. : -
—
o
Ambient temperature t2 ( C) .................................. : Temperature rise dT of winding:
R1 (Ω)
EMC compliance Ltd.
R2 (Ω)
—
dT (K)
Limit dT (K)
Insulation
class
Page: 22 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
7.2
TABLE: softening temperature of thermoplastics
Temperature T of part
10.3
Result - Remark
Verdict
N/A
T - normal conditions (oC)
T - fault conditions (oC)
T softening
(oC)
TABLE: insulation resistance measurements
P
Insulation resistance R between:
R (MΩ)
Required R (MΩ)
Primary – Enclosure (Ground)
≥ 100
≥ 2
10.3
TABLE: electric strength measurements
P
Test voltage applied between:
Test voltage (V)
Breakdown
Primary – Enclosure (Ground)
2 120 Vp
No
11.2
TABLE: summary of fault condition tests
P
Voltage (V) 0,9 or 1,1 times rated voltage ............. : 253
—
Ambient temperature (ºC) ...................................... : 20-30
—
fault condition, state component short- or
open circuited and components whose
temperature rises are measured
Interruption of Protect Earth
supply voltage
253
result, state effect of fault condition and the
duration of the test
Normal operated, No hazard.
Duration: 30 min., Final input current: 45 mA
Winding temperature rise measurements
N/A
Ambient temperature t1 (ºC) .................................. :
—
Ambient temperature t2 (ºC) .................................. :
—
EMC compliance Ltd.
Page: 23 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
Clause
Requirement – Test
14
TABLE: list of critical components and materials
Component
Result - Remark
Manufacturer/
Type/model
Verdict
P
Value / rating
Standard
Approval/
trademark
Fuse
215
2 A H 250V
IEC/EN 60127-2 VDE
Multiway
Openwise
terminal block
Industrial
with Fuse holder Limited
540
2.5/4.0 mm2,
400 V with fuse
holder 6.3 A,
250, 2.5 W
EN 60998-2-1,
EN 60127-6
AC Fan
Fulltech Electric
Co., Ltd.
UF-60D23
230 V, 50/60 Hz, EN 60335-1
5/4 W
VDE
Bimetal
Thermostat
(SW2)
Inchang
Electronics Co.,
Ltd.
KS-2R R45
250 V, 7.5 A,
45 ºC
EN 60730-1,
EN 60730-2-9
VDE
Bimetal
Thermostat
(SW1, SW3)
Inchang
Electronics Co.,
Ltd.
KS-2N N15
250 V, 7.5 A,
4 ºC
EN 60730-1,
EN 60730-2-9
VDE
Low-Heater 1,2
Jiangyin Huilong Heater Co., Ltd.
230 V, 20 W
EN 60065
Tested in
equipment
DEF Heater
Jiangyin Huilong Heater Co., Ltd.
230 V, 10 W
EN 60065
Tested in
equipment
Cable Grand 1
Heyco Products
Inc
3232
V-2, IP68, 1/2”
-
UL
Cable Grand 2,3 Heyco Products
Inc
3229
V-2, IP68, 3/8”
-
UL
V-0, 105 ºC
UL 796
UL
PCB
Littelfuse
Reference
Ningbo Junchao
Electronic
JC
Technology Co.,
Ltd.
FIMKO
1
) an asterisk indicates a mark which assures the agreed level of surveillance
EMC compliance Ltd.
Page: 24 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
CE TEST REPORT
Report No.: 10EMC-CE-S004
Clause
Requirement – Test
ZB
ANNEX ZB TO EN 60 065, SPECIAL NATIONAL CONDITIONS
2.6.1
DK: certain types of Class I apparatus, see 15.1.1,
may be provided with a plug not establishing
earthing continuity when inserted in Danish socketoutlets
N/A
13.3.1
NO: In Norway, due to IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230V in case of a single earth fault.
N/A
15.1.1
DK: mains cord for single-phase equipment having
a rated current not exceeding 10 A shall be
provided with a plug according to Heavy Current
Regulations Section 107-2-D1
N/A
DK: Class I equipment with socket-outlets with
earthing contact, or which are intended to be used
in locations where protection against indirect
contact is required shall be provided with a plug in
compliance with Standard Sheet DK 2-1a
N/A
DK: socket-outlets for providing power to Class II
equipment with a rated current of 2,5 A shall have
dimensions according to the drawing on page 131
of EN 60 065:98 other dimensions shall be to
IEC 60 083 Standard Sheet C 1a for portable
socket-outlets
N/A
DK: mains socket-outlets with earthing contact
shall comply with Heavy Current Regulations
Section 107-2-D1, Standard Sheet DK1-3a,
DK 1-5a or DK 1-7a
N/A
GB: equipment fitted with a flexible cable or cord
provided with a 13A BS 1363 plug as in Statutory
Instrument 1768:94
N/A
IE: equipment fitted with a flexible cable or cord
provided with a 13A plug in accordance with
Statutory Instrument 525:97
N/A
NO: mains socket-outlets on Class II equipment meet CEE Publication 7 with the
following amendments:
N/A
- dimensions 2,5 A, 250 V socket-outlets shall
comply with Standard Sheet 1 page 132 of
EN 60 065:98
N/A
-mechanical strength 2,5 A, 250 V socket-outlets
tested as specified in EN 60 065, 12.1.3
N/A
-protecting rim also tested
N/A
EMC compliance Ltd.
Result - Remark
Verdict
Page: 25 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
http://www.emc2000.co.kr
Clause
CE TEST REPORT
Report No.: 10EMC-CE-S004
Requirement – Test
Result - Remark
Verdict
NO: method b) of 8.1 is not permitted. Double or
reinforced insulation is required between parts
connected to the mains and parts connected to the
public telecommunications network
N/A
J.2
NO: In Norway, due to IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230V in case of a single earth fault.
N/A
ZC
ANNEX ZC TO EN 60 065, A-DEVIATIONS
5
DE: additional markings required in German language:
5.1
14
-cathode ray tubes with an accelerating voltage
between 20 kV and 30 kV (marking on the tube)
N/A
-TV receivers whose picture tube has an
accelerating voltage between 20 kV and 30 kV
N/A
-TV receivers whose picture tube has an
accelerating voltage greater than 30 kV
N/A
TV receivers whose picture tube has an
accelerating voltage less than 20 kV
N/A
IT: additional markings on the outside of the TV
receiver in Italian language
N/A
IT: user instructions in Italian language including a
conformity declaration
N/A
IT: certification number on the back cover
N/A
SE: Switches containing mercury such as
thermostats, relays and level controllers are not
allowed
N/A
EMC compliance Ltd.
Page: 26 of 26
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
Fig 1. Outside view 1
EMC
compliance
Ltd.
Attachment page: 1 of 3
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
Fig 2. Outside view 2
EMC
compliance
Ltd.
Attachment page: 2 of 3
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
CE TEST REPORT
Report No.: 10EMC-CE-S004
http://www.emc2000.co.kr
Fig 3. Inside view
EMC
compliance
Ltd.
Attachment page: 3 of 3
480-5 Shin-dong, Yeongtong-gu, Suwon-shi, Kyunggi-do,443-390, Korea
82 31 336 9919 (Main) 82 31 336 4767 (Fax)
This test report shall not be reproduced except in full, Without the written approval.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement