TEST REPORT

TEST REPORT
Test Report
Test Report No.:CERASH03061001
EN 60950
Clause
Requirement - Test
Result -remark
Verdict
TEST REPORT
EN 60950
Safety of information technology equipment including electrical business equipment
Report reference No.:
Compiled by ﹙+ signature﹚:
Approved by ﹙+ signature﹚:
Date of issue:
ASH03061001
Fenix Yang
Leon Tien
July 07, 2003
Testing laboratory:
Address:
QuieTek Corporation .
3135 Kashiwa Street
Torrance, CA 90505, USA
as above
TRENDware International Inc.
18F-1, No. 79, Sec. 1, Hsin Taiwu Road, Hsichih, Taipei,
Taiwan.
IEC 60950:1999, EN 60950:2000
Standard
1-Port USB Print Server
TRENDware, TRENDnet
TEW-PS1U
Testing location:
Applicant:
Address:
Standard:
Test procedure:
Type of test object:
Trademark:
Model / type reference:
Manufacturer:
Address:
___________________
__
____
Same as applicant
Factory:
Address:
Rating:
+5Vdc
Other Aspects:
The completed test report – includes the following documents: (total page 38)
Test results given in this report only relate to the specimen(s) tested, calibrated or measured.
This report shall not be reproduced other than in full without the written consent of Quietek.
1 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Test item particulars:
Equipment mobility……………….…….…...:
Operating condition ……………….….……..:
Tested for IT power systems……….….……..:
IT testing, phase-phase voltage(v)….………..:
Class of equipment…………………….…….:
Result -remark
Verdict
Transportable.
continuous
No mains connection
N.A.
Class III
Mass of equipment (kg)……………….….….: Approx. 45g
Protection against ingress of water……..……: IPX0
Possible test case verdicts:
- test case does not apply to the object……….: N(.A.)
- test object does meet the requirement………: P(ass)
- test object does not meet the requirement.….: F(ail )
General remarks:
“(see remark # )” refers to a remark appended to the report.
“(see appended table)” refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
The test results presented in this report relate only to the object tested
This report shall not be reproduced except in full without the written approval of the testing
laboratory.
Comments:
Brief description of the test sample:
The equipment’s power source from AC adaptor (L.P.S.)
Top enclosure - overall 90 by 80 by 40 mm, secured together by tube..
The devices are for continuous operation.
The ambient temperature for 40℃.
2 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Test item particulars:
Equipment mobility……………….…….…...:
Operating condition ……………….….……..:
Tested for IT power systems……….….……..:
IT testing, phase-phase voltage(v)….………..:
Class of equipment…………………….…….:
Result -remark
Verdict
Transportable.
continuous
No mains connection
N.A.
Class III
Mass of equipment (kg)……………….….….: Approx. 45g
Protection against ingress of water……..……: IPX0
Possible test case verdicts:
- test case does not apply to the object……….: N(.A.)
- test object does meet the requirement………: P(ass)
- test object does not meet the requirement.….: F(ail )
General remarks:
“(see remark # )” refers to a remark appended to the report.
“(see appended table)” refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
The test results presented in this report relate only to the object tested
This report shall not be reproduced except in full without the written approval of the testing
laboratory.
Comments:
Brief description of the test sample:
The equipment’s power source from AC adaptor (L.P.S.)
Top enclosure - overall 90 by 80 by 40 mm, secured together by tube..
The devices are for continuous operation.
The ambient temperature for 40℃.
3 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
TRENDnet
_________________________________________________________________
Wireless 1-Port Print Server (USB)
Model: TEW-PS1U
Rating: 5Vdc
1
GENERAL
P
1.5
Components
P
1.5.1
Comply with IEC 60950 or relevant
component standard
Components, which were
found to affect safety
aspects, comply with the
requirements of this
standard or within the
safety aspects of the
relevant IEC component
standards (see appended
table 1.5.1).
P
1.5.2
Evaluation and testing of components
Components, which are
certified to IEC and/or
national standards, are used
correctly within their
ratings. Components not
covered by IEC standards
are tested under the
conditions present in the
equipment.
P
Dimensions (mm) of mains plug for direct
Not direct plug-in type.
plug-in
:
4 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
4
Torque and pull test of mains plug for direct dto.
plug-in; torque (Nm); pull (N) ...................... :
N
1.5.3
Thermal controls
No thermal control.
N
1.5.4
Transformers
No transformer.
N
1.5.5
Interconnecting cables
Interconnection cable for
signal connected to PC is
carrying only SELV on an
energy level below 240VA.
P
→ Except for the insulation
material there are no
further requirements to the
interconnection cable.
1.5.6
Capacitors in primary circuits ..................... : Class III equipment.
N
1.5.7
Double or reinforced insulation bridged by
components
N
1.5.7.1
Bridging capacitors
N
1.5.7.2
Bridging resistors
N
1.5.7.3
Accessible parts
N
1.5.8
Components in equipment for IT power
systems
1.6
Power interface
P
1.6.1
AC power distribution systems......................: Class III equipment.
N
1.6.2
Input current
Class III equipment.
Normal load according to
1.2.2.1 for this equipment is
movement of mouse.
N
P
(see appended table 1.6.2)
1.6.3
Voltage limit of hand-held equipment
Class III equipment.
N
1.6.4
Neutral conductor
Class III equipment.
N
1.7
Marking and instructions
1.7.1
Power rating
P
See below.
Rated voltage(s) or voltage range(s) (V) ..... : DC 5V
5 - 45
P
P
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
Symbol for nature of supply for d.c. ............ :
P
Rated frequency or frequency range (Hz) .... : No direct connection to the
AC mains supply.
N
Rated current (mA or A) .............................. : Not shown
P
Manufacturer’s name/Trademark ................. : TRENDware
P
Type/model .................................................. : 1) TEW-PS1U
P
Symbol of Class II ........................................ : Class III equipment.
N
Other symbols ............................................. : Additional symbols or
markings do not give rise to
misunderstanding.
P
Certification marks ....................................... :
N
1.7.2
Safety instructions
N
1.7.3
Short duty cycles
1.7.4
Supply voltage adjustment .......................... : No voltage/frequency
setting.
N
1.7.5
Power outlets on the equipment .................. : No outlet.
N
Equipment is designed for
continuous operation.
6 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
1.7.6
Fuse identification ....................................... : No fuse.
N
1.7.7
Wiring terminals
See below.
N
1.7.7.1
Protective earthing and bonding terminals
Class III equipment.
N
1.7.7.2
Terminal for a.c. mains supply conductors
Class III equipment.
N
1.7.8
Controls and indicators
No safety relevant switch or
control.

1.7.8.1
Identification, location and marking ............ :
N
1.7.8.2
Colours ....................................................... :
N
1.7.8.3
Symbols according to IEC 60417 ................. :
N
1.7.8.4
Markings using figures ............................... : No indicators.
N
1.7.9
Isolation of multiple power sources ............. : Class III equipment.
N
1.7.10
IT power system
Class III equipment.
N
1.7.11
Thermostats and other regulating devices
No thermostat or other
regulating device.
N
1.7.12
Language ..................................................... : Marking and user’s manual
in English. Version of other
language will be provided
when national approval.
P
1.7.13
Durability
P
The label was subjected to
the permanence of marking
test. The label was rubbed
with cloth soaked with
water for 15s and then
again for 15s with the cloth
soaked with petroleum
spirit.
After this test there was no
damage to the label. The
marking on the label did
not fade. There was no
curling nor lifting of the
label edge.
1.7.14
Removable parts
1.7.15
Replaceable batteries
No required markings
placed on removable parts.
N
N
7 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
Language....................................................... :

1.7.16
Operator access with a tool ........................... : Only SELV inside.
N
1.7.17
Equipment for restricted access locations..... : No restricted access
location.
N
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
P
2.1.1.1
Access to energised parts

Test by inspection ........................................:
N
Test with test finger .....................................:
N
Test with test pin ..........................................:
N
Test with test probe ......................................:
N
2.1.1.2
Battery compartments ....................................:
N
2.1.1.3
Access to ELV wiring
N
Working voltage (V); distance (mm) trough
insulation

2.1.1.4
Access to hazardous voltage circuit wiring
N
2.1.1.5
Energy hazards .............................................: No energy hazard in
operator access area. The
connectors on the backside
of the equipment below
240VA.
P
2.1.1.6
Manual controls
N
2.1.1.7
Discharge of capacitor s in the primary
circuit
N
Time-constant (s); measured voltage (V) ......:

See below.
No manual controls
2.1.2
Protection in service access areas
No maintenance work in
operation mode necessary.
N
2.1.3
Protection in restricted access locations
It is not intended to be used
in restricted locations
N
8 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
2.2
SELV circuits
2.2.1
General requirements
The secondary circuits
were tested as SELV. See
2.2.1 to 2.2.4.
P
2.2.2
Voltages under normal conditions (V)...........: 42.4V peak or 60Vd.c. are
not exceeded in SELV
circuit under normal
operation, see appended
table 2.2.2.
P
2.2.3
Voltages under fault conditions (V)...............: Single fault did not cause
excessive voltage in
accessible SELV circuits.
Limits of 71V peak and
120Vd.c. did not exceeded
within 0.2s and limits
42.4V peak and 60Vd.c.
did not exceeded for longer
than 0.2 s, see appended
tables 2.2.2 and 5.3.
P
2.2.3.1
Separation by double or reinforced insulation Class III equipment.
(method 1)
N
2.2.3.2
Separation by earthed screen (method 2)
dto
N
2.2.3.3
Protection by earthing of the SELV circuit
(method 3)
dto
N
2.2.4
Connection of SELV circuits to other circuits Only SELV circuit
........................................................................: provided.
N
2.3
TNV circuits
N
P
No TNV circuit.
2.3.1
2.3.2
2.3.3
Limits
N
Type of TNV circuits .....................................:

Separation from other circuits and from
accessible parts
N
Used insulation...............................................:

Separation from hazardous voltages
N
Used insulation...............................................:

9 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
2.3.4
Requirement - Test
Result -remark
Verdict
Connection of TNV circuits to other circuits
N
Used insulation...............................................:

2.3.5
Test for operating voltages generated
externally
N
2.4
Limited current circuits
N
2.4.1
General requirements
N
2.4.2
Limit values
N
Frequency (Hz) ............................................. :

Measured current (mA)................................. :

Measured voltage (V) ................................... :

Measured capacitance (µF) ........................... :

2.4.3
Connection of limited current circuits to
other circuits
N
2.5
Limited power sources
N
Inherently limited output
N
Impedance limited output
N
Overcurrent protective device limited output
N
Regulating network limited output under
normal operating and single fault condition
N
Regulating network limited output under
normal operating conditions and overcurrent
protective device limited output under single
fault condition
N
Output voltage (V), output current (A),
apparent power (VA) .....................................:

Current rating of overcurrent protective
device (A)

Provisions for earthing and bonding
N
2.6
Class III equipment.
10 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
2.6.1
Protective earthing
N
2.6.2
Functional earthing
N
2.6.3
Protective earthing and protective bonding
conductors
N
2.6.3.1
Size of protective earthing conductors
N
Rated current (A), cross-sectional area
(mm2), AWG ..................................................:

Size of protective bonding conductors
N
Rated current (A), cross-sectional area
(mm2), AWG ................................................ :

Rated current (A), type and nominal thread
diameter (mm) .............................................. :
N
Resistance (Ω) of earthing conductors and
their terminations, test current (A) ............... :
N
2.6.3.4
Colour of insulation...................................... :
N
2.6.4
Terminals
N
2.6.4.1
Protective earthing and bonding terminals
N
Rated current (A), type and nominal thread
diameter (mm) ............................................... :

2.6.4.2
Separation of the protective earthing
conductor from protective bonding
conductors
N
2.6.5
Integrity of protective earthing
N
2.6.5.1
Interconnection of equipment
N
2.6.5.2
Components in protective earthing
conductors and protective bonding
conductors
N
2.6.5.3
Disconnection of protective earth
N
2.6.5.4
Parts that can be removed by an operator
N
2.6.5.5
Parts removed during servicing
N
2.6.5.6
Corrosion resistance
N
2.6.5.7
Screws for protective bonding
N
2.6.5.8
Reliance on telecommunication network
N
2.6.3.2
2.6.3.3
11 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
2.7
Requirement - Test
Result -remark
Overcurrent and earth fault protection in primary circuits
Verdict
N
The wireless mouse is supplied by two AAA batteries and receiver supplied
from a PC that is assumed to provide only SELV.
2.7.1
Basic requirements
N
2.7.2
Faults not covered in 5.3
N
2.7.3
Short-circuit backup protection
N
2.7.4
Number and location of protective devices .. :
N
2.7.5
Protection by several devices
N
2.7.6
Warning to service personnel.........................:
N
2.8
Safety interlocks
N
No safety interlock.
2.8.1
General principles
N
2.8.2
Protection requirements
N
2.8.3
Inadvertent reactivation
N
2.8.4
Fail-safe operation
N
2.8.5
Interlocks with moving parts
N
2.8.6
Overriding an interlock
N
2.8.7
Switches and relays in interlock systems
N
2.8.7.1
Contact gaps (mm) .......................................:
N
2.8.7.2
Overload test
N
2.8.7.3
Endurance test
N
2.8.7.4
Electric strength test (V)
N
2.8.8
Mechanical actuators
N
2.9
Electrical insulation
P
Only SELV inside the unit →
sub clause 5.3.4)
2.9.1
no requirement on insulation. (See also
Properties of insulating materials
P
12 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
2.9.2
Humidity conditioning
P
2.9.3
Requirements for insulation
P
2.9.4
Insulation parameters
P
2.9.5
Categories of insulation
P
2.10
Clearances, creepage distances and distances through insulation
N
See also sub clause 5.3.4.
2.10.1
General
N
2.10.2
Determination of working voltage
N
2.10.3
Clearances
N
2.10.3.1
General
N
2.10.3.2
Clearances in primary circuit
N
2.10.3.3
Clearances in secondary circuits
N
2.10.3.4
Measurement of transient levels
N
2.10.4
Creepage distances
N
CTI tests .........................................................:

2.10.5
Solid insulation
N
2.10.5.1
Minimum distance through insulation
N
2.10.5.2
Thin sheet material
N
Number of layers (pcs).................................. :

Electric strength test

2.10.5.3
Printed boards .............................................. : Not applied for.
N
2.10.5.4
Wound components...................................... :
N
2.10.6
Coated printed boards
2.10.6.1
General
N
2.10.6.2
Sample preparation and preliminary
inspection ..................................................... :
N
2.10.6.3
Thermal cycling ........................................... :
N
2.10.6.4
Thermal ageing ............................................ :
N
2.10.6.5
Electric strength test
N
No coated printed boards.
13 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
2.10.6.6
Requirement - Test
Result -remark
Verdict
Abrasion resistance test................................ :
N
Electric strength test
N
2.10.7
Enclosed and sealed parts ............................ : No hermetically sealed
components.
N
2.10.8
Spacings filled by insulating compound ...... :
N
Electric strength test
N
2.10.9
Component external terminations
N
2.10.10
Insulation with varying dimensions
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
Insulation kept
homogenous.
All internal wires are UL
recognized wiring which is
PVC insulated, rated VW-1,
minimum 80oC, 300V.
Internal wiring gauge is
suitable for current intended
to be carried.
N
P
No internal wire for
primary power distribution.
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges, which could damage
the insulation and cause
hazard.
P
3.1.3
Securing of internal wiring
Internal wires are routed.
The wires are secured by
solder pins and quick
connect terminals so that a
loosening of the terminal
connection is unlikely.
P
3.1.4
Insulation of conductors
N
3.1.5
Beads and ceramic insulators
N
3.1.6
Screws for electrical contact pressure
N
14 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
3.1.7
Non-metallic materials in electrical
connections
N
3.1.8
Self-tapping and spaced thread screws
N
3.1.9
Termination of conductors
N
3.1.10
Sleeving on wiring
N
3.2
Connection to a.c. mains supplies
N
Class III equipment.
3.2.1
Means of connection
N
3.2.2
Multiple supply connections
N
3.2.3
Permanently connected equipment
N
Number of conductors, diameter (mm) of
cable and conduits ......................................:

3.2.4
Appliance inlets
N
3.2.5
Power supply cords
N
Type..............................................................:

Rated current (A), cross-sectional area
(mm2), AWG .............................................:

Cord anchorages and strain relief
N
3.2.6
.............:

Longitudinal displacement (mm) ...............:

3.2.7
Protection against mechanical damage
N
3.2.8
Cord guards
N
D (mm); test mass (g) .................................:

Radius of curvature of cord (mm) ................:

3.2.9
Supply wiring space
N
3.3
Wiring terminals for connection of external conductors
N
Mass of equipment (kg), pull (N)
Class III equipment.
3.3.1
Wiring terminals
N
15 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
3.3.2
Connection of non-detachable power supply
cords
N
3.3.3
Screw terminals
N
3.3.4
Rated current (A), cord/cable type,
cross-sectional area (mm2) .............................:
N
3.3.5
Rated current (A), type and nominal thread
diameter (mm)................................................:
N
3.3.6
Wiring terminals design
N
3.3.7
Grouping of wiring terminals
N
3.3.8
Standard wire
N
3.4
Disconnection from the a.c. mains supply
N
Class III equipment.
3.4.1
General requirement
N
3.4.2
Disconnect devices
N
3.4.3
Permanently connected equipment
N
3.4.4
Parts which remain energized
N
3.4.5
Switches in flexible cords
N
3.4.6
Single-phase equipment
N
3.4.7
Three-phase equipment
N
3.4.8
Switches as disconnect devices
N
3.4.9
Plugs as disconnect devices
N
3.4.10
Interconnected equipment
N
3.4.11
Multiple power sources
N
3.5
Interconnection of equipment
P
3.5.1
General requirements
3.5.2
Types of interconnection circuits .................. : Interconnection circuits of
SELV through the
connectors. No ELV
interconnection circuits.
See below.
16 - 45
P
P
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
No ELV interconnection
Verdict
N
3.5.3
ELV circuits as interconnection circuits
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
N
This appliance is of a stable
mechanical construction
and does not overbalance
when tilted to an angle of
10° from its normal
upright position.
Angle of 10°
4.2
P
Test: force (N) ............................................... : Equipment is not a
floorstanding unit.
N
Mechanical strength
P
As there are no hazardous voltages present in the unit or other hazards
foreseeable, the tests of these clauses were not performed but replaced by
a construction review only.
4.2.1
General
N
4.2.2
Steady force test, 10 N
N
4.2.3
Steady force test, 30 N
N
4.2.4
Steady force test, 250 N
N
4.2.5
Impact test
N
4.2.6
Drop test
N
4.2.7
Stress relief
N
4.2.8
Cathode ray tubes

Picture tube separately certified................... :
N
Picture tubes > 16 cm intrinsically protected
N
Non-intrinsically protected tubes > 16cm
used with protective screen
N
Intrinsically protected tubes: tests on 12
samples
N
Samples subject to ageing: 6
N
Samples subject to implosion test: 6
N
17 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
Samples subject to mechanical strength test
(steel ball): 6
N
Non-intrinsically protected tubes tested
N
4.2.9
High pressure lamps
N
4.2.10
Wall or ceiling mounted equipment; force
(N) .............................................................. :
N
4.3
Design and construction
P
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ...... :
4.3.3
Adjustable controls
None that would cause
hazard.
N
4.3.4
Securing of parts
Electrical and mechanical
connections can be
expected to with standard
usual mechanical stress.
For the protection solder
pins are used.
P
4.3.5
Connection of plugs and sockets
4.3.6
Direct plug-in equipment
Edges and corners of the
enclosure are rounded.
P
N
N
Not direct plug-in type.
N

Torque (Nm) ................................................ :
4.3.7
Heating elements in earthed equipment
Class III equipment.
N
4.3.8
Batteries
The wireless mouse
supplied by two AAA
non-rechargeable
carbon-zinc or alkaline
batteries only.
N
4.3.9
Oil and grease
No oil or grease.
N
4.3.10
Dust, powders, liquids and gases
Equipment in intended use
not considered to be
exposed to these.
P
4.3.11
Containers for liquids or gases
No container for liquid or
gas.
N
4.3.12
Flammable liquids........................................ : No flammable liquid.
18 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
4.3.13
4.4
Requirement - Test
Result -remark
Verdict
Quantity of liquid (l) .................................... :
N
Flash point (°C)............................................ :
N
Radiation; type of radiation ....................... :
N
Equipment using lasers, see separate test
report of IEC 60825-1.
N
Protection against hazardous moving parts
N
No hazardous moving part.
4.4.1
General
N
4.4.2
Protection in operator access areas
N
4.4.3
Protection in restricted access locations
N
4.4.4
Protection in service access areas
N
4.5
Thermal requirements
P
The mouse and receiver have no significant temperature rise on critical
components as the input power is <1W only, therefore no temperature rise
test was done.
4.5.1
Temperature rises
(see appended table)
4.5.2
Resistance to abnormal heat
N
4.6
Openings in enclosures
N
4.6.1
Top and side openings
No electrical enclosure
required.
Bottoms of fire enclosures
There is no openings at
bottom of enclosure.
Construction of the bottom .......................... : (see appended table)
19 - 45
N

Dimensions (mm) ...................................... :
4.6.2
P
P

Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
4.6.3
Doors or covers in fire enclosures
The fire enclosure contains
an operator removal cover
which intended only for
occasional use (installing
battery). There are
instructions provided for
correct removal and
installation within the
user’s manual.
P
4.6.4
Openings in transportable equipment
Equipment is not
transportable equipment.
N
4.6.5
Adhesives for constructional purposes
N
4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of
flame
Use of materials with the
required flammability
classes.
P
4.7.2
Conditions for a fire enclosure
See 4.7.2.1.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following
components:
P
components in
secondary (not supplied
by LPS)
insulated wiring
the fire enclosure is
required. However,
according to decisions by
operating staff meeting
(documents OSM/EE
(Chairman)9/99, the
enclosure of keyboard or
similar devices can be
accepted to be made of
material class HB min.
based on abnormal test.
There is no fire hazard after
5.3. Enclosure material
rated flammability class HB
material is acceptable here.
20 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
4.7.2.2
Parts not requiring a fire enclosure
See 4.7.2.1.
N
4.7.3
Materials
See below.
P
4.7.3.1
General
PCB rated V-1 or better.
P
4.7.3.2
Materials for fire enclosures
See 4.7.2.1.
N
4.7.3.3
Materials for components and other parts
outside fire enclosures
dto
N
4.7.3.4
Materials for components and other parts
inside fire enclosures
Internal components except
small parts are V-2, HF-2
or better.
P
4.7.3.5
Materials for air filter assemblies
No air filter assemblies.
N
4.7.3.6
Materials used in high-voltage components
No high voltage
component.
N
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL
CONDITIONS
P
5.1
Touch current and protective conductor current
N
Class III equipment without TNV circuit.
5.1.1
General
N
5.1.2
Equipment under test (EUT)
N
5.1.3
Test circuit
N
5.1.4
Application of measuring instrument
N
5.1.5
Test procedure
N
5.1.6
Test measurements
N
Test voltage (V) ......................................... :

Measured current (mA) .............................. :

Max. allowed current (mA) ....................... :

5.1.7
Equipment with touch current exceeding 3.5
A ........................................................... :
N
5.1.8
Touch currents to and from
telecommunication networks
N
21 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
5.1.8.1
Requirement - Test
Result -remark
Verdict
Limitation of the touch current to a
telecommunication network
N
Test voltage (V) ......................................... :

Measured current (mA) .............................. :

Max. allowed current (mA) ....................... :

5.1.8.2
Summation of touch currents from
telecommunication networks ....................... :
N
5.2
Electric strength
N
Class III equipment.
5.2.1
General
N
5.2.2
Test procedure
N
5.3
Abnormal operating and fault conditions
N
5.3.1
Protection against overload and abnormal
operation
N
5.3.2
Motors
No motor.
N
5.3.3
Transformers
No isolating transformer
used.
N
5.3.4
Functional insulation.................................... :
5.3.5
Electromechanical components
No electromechanical
component.
N
5.3.6
Simulation of faults
No other abnormal tests
necessary.
N
5.3.7
Unattended equipment
Equipment was not
intended for unattended
use.
N
5.3.8
Compliance criteria for abnormal operating
and fault conditions
N
5.3.8.1
During the tests
N
5.3.8.2
After the tests
N
Considered.
22 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
6
Requirement - Test
Result -remark
CONNECTION TO TELECOMMUNICATION NETWORKS
Verdict
N
No TNV.
6.1
Protection of telecommunication network service personnel, and users of
other equipment connected to the network, from hazards in the equipment
N
6.1.1
Protection from hazardous voltages
N
6.1.2
Separation of the telecommunication network from earth
N
6.1.2.1
Requirements
N
Test voltage (V) ..........................................:

Current
(mA) ............:

6.1.2.2
Exclusions ....................................................:
N
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N
6.2.1
Separation requirements
N
6.2.2
Electric strength test procedure
N
6.2.2.1
Impulse test
N
6.2.2.2
Steady-state test
N
6.2.2.3
Compliance criteria
N
6.3
Protection of telecommunication wiring system from overheating
N
Max. output current (A) ............................... :

Current limiting method............................... :

A
ANNEX , TESTS FOR RESISTANCE TO HEAT AND FIRE
N
A.1
Flammability test for fire enclosures of movable equipment having a total
mass exceeding 18 g, and of stationary equipment (see 4.7.3.2)
N
A.1.1
Samples
N
Wall thickness (mm) .................................... :

A.1.2
Conditioning of samples; temperature (°C) . :
N
A.1.3
Mounting of samples.................................... :
N
in the test circuit
23 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
A.1.4
Test flame
N
A.1.5
Test procedure
N
A.1.6
Compliance criteria
N
Sample 1 burning time (s)............................ :

Sample 2 burning time (s)............................ :

Sample 3 burning time (s)............................ :

A.2
Flammability test for fire enclosures of movable equipment having a total
mass not exceeding 18 kg, and for material and components located inside
fire enclosures (see 4.7.3.2 and 4.7.3.4)
N
A.2.1
Samples
N
Wall thickness (mm) .................................... :

A.2.2
Conditioning of samples; temperature (°C) . :
N
A.2.3
Mounting of samples.................................... :
N
A.2.4
Test flame
N
A.2.5
Test procedure
N
A.2.6
Compliance criteria
N
Sample 1 burning time (s)............................ :

Sample 2 burning time (s)............................ :

Sample 3 burning time (s)............................ :

Alternative test acc. to IEC 60695-2-2, cl. 4,
8
N
Sample 1 burning time (s)............................ :

Sample 2 burning time (s)............................ :

Sample 3 burning time (s)............................ :

A.3
High current arcing ignition test (see 4.7.3.2)
N
A.3.1
Samples
N
Wall thickness (mm) .................................... :

A.3.2
Test circuit
N
A.3.3
Test electrodes
N
A.3.4
Test procedure
N
A.2.7
24 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
A.3.5
Requirement - Test
Result -remark
Verdict
Compliance criteria
N
Sample 1 number of arcs to ignition (pcs) ... :

Sample 2 number of arcs to ignition (pcs) ... :

Sample 3 number of arcs to ignition (pcs) :

Sample 4 number of arcs to ignition (pcs) :

Sample 5 number of arcs to ignition (pcs) ... :

A.4
Hot wire ignition test (see 4.7.3.2)
N
A.4.1
Samples
N
Wall thickness (mm) .................................... :

A.4.2
Test circuit
N
A.4.3
Mounting of samples.................................... :
N
A.4.4
Test procedure
N
A.4.5
Compliance criteria
N
Sample 1 ignition time (s)............................ :

Sample 2 ignition time (s)............................ :

Sample 3 ignition time (s)............................ :

Sample 4 ignition time (s)............................ :

Sample 5 ignition time (s)............................ :

A.5
Hot flaming oil test (see 4.6.2)
N
A.5.1
Mounting of samples.................................... :
N
A.5.2
Test procedure
N
A.5.3
Compliance criterion.................................... :
N
A.6
Flammability tests for classifying materials V-0, V-1 or V-2
N
A.6.1
Samples
N
Wall thickness (mm) .................................... :

A.6.2
Conditioning of samples temperature (°C)... :
N
A.6.3
Mounting of samples.................................... :
N
A.6.4
Test procedure
N
A.6.5
Compliance criteria
N
25 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
A.6.6
Permitted retest
N
A.7
Flammability test for classifying foamed materials HF-1, HF-2 or HFB
N
A.7.1
Sample
N
Wall thickness (mm) .................................... :

A.7.2
Conditioning of samples; temperature (°C) . :
N
A.7.3
Test procedure
N
A.7.4
Compliance criteria
N
A.7.5
Compliance criteria, HF-2
N
A.7.6
Compliance criteria, HF-1
N
A.7.7
Compliance criteria, HBF
N
A.7.8
Permitted retest, HF-1 or HF-2
N
A.7.9
Permitted retest, HBF
N
A.8
Flammability test for classifying materials HB
N
A.8.1
Samples
N
Sample thickness (mm)................................ :

A.8.2
Conditioning of samples; temperature (°C) . :
N
A.8.3
Mounting of samples.................................... :
N
A.8.4
Test procedure
N
A.8.5
Compliance criteria
N
A.8.6
Permitted retest
N
A.9
Flammability test for classifying materials 5V
N
A.9.1
Samples
N
Sample thickness (mm)................................ :

A.9.2
Conditioning of samples temperature (°C)... :
N
A.9.3
Test flame
N
A.9.4
Test procedure, test bars
N
A.9.5
Test procedure, test plaques
N
A.9.6
Compliance criteria .................................... :
N
A.9.7
Permitted retest
N
26 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
A.10
Requirement - Test
Result -remark
Verdict
Stress relief conditioning (see 4.2.7)
N
Temperature (°C).......................................... :

B
ANNEX , MOTOR TESTS UNDER ABNORMAL CONDITIONS
N
B.1
General requirements
N
Position .......................................................:

Manufacturer ...............................................:

Type ............................................................:

Rated values

..............................................:
B.2
Test conditions
N
B.3
Maximum temperatures
N
B.4
Running overload test
N
B.5
Locked-rotor overload test
N
Test duration (days) ....................................:

Electric strength test: test voltage (V) .........:

B.6
Running overload test for DC motors in
secondary circuits
N
B.7
Locked-rotor overload test for DC motors in secondary circuits
N
B.7.1
Test procedure
N
B.7.2
Alternative test procedure; test time (h) ........:
N
B.7.3
Electric strength test
N
B.8
Test for motors with capacitors
N
B.9
Test for three-phase motors
N
B.10
Test for series motors
N
Operating voltage (V) .................................:

ANNEX , TRANSFORMERS
N
Position .......................................................:

Manufacturer ...............................................:

Type ............................................................:

C
27 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Rated values
Result -remark
..............................................:
Verdict

C.1
Overload test
N
C.2
Insulation
N
D
ANNEX , MEASURING INSTRUMENTS FOR TOUCH-CURRENT
TESTS (see 5.1.4)
N
D.1
Measuring instrument
N
D.2
Alternative measuring instrument
N
E
ANNEX , TEMPERATURE RISE OF A WINDING (see 1.4.13 and
4.5.1)
N
F
ANNEX , MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
N
G
ANNEX , ALTERNATIVE METHOD FOR DETERMINING
MINIMUM CLEARANCES
N
G.1
Summary of the procedure for determining
minimum clearances
N
G.2
Determination of mains transient voltage (V)
...................................................................... :
N
G.3
Determination of telecommunication
network transient voltage (V) ...................... :
N
G.4
Determination of required withstand voltage
(V) ................................................................ :
N
G.5
Measurement of transient levels (V)............ :
N
G.6
Determination of minimum clearances ........ :
N
H
ANNEX , IONIZING RADIATION (see 4.3.13)
N
Ionizing radiation
N
Measured radiation (mR/h) ......................... :

Measured high-voltage (kV) ........................ :

28 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
Measured focus voltage (kV) ....................... :

CRT markings .............................................. :

ANNEX , TABLE OF ELECTROCHEMICAL POTENTIALS (see
2.6.5.6)
N
Metal used .....................................................:

K
ANNEX , THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N
K.1
Making and breaking capacity
N
K.2
Thermostat reliability; operating voltage (V):
N
K.3
Thermostat endurance test; operating voltage
(V) .............................................................. :
N
K.4
Temperature limiter endurance; operating
voltage (V) ................................................. :
N
K.5
Thermal cut-out reliability
N
K.6
Stability of operation
N
L
ANNEX , NORMAL LOAD CONDITIONS FOR SOME TYPES OF
ELECTRICAL BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.1)
P
L.1
Typewriters
No typewriter.
N
L.2
Adding machines and cash registers
No adding machine or cash
registers.
N
L.3
Erasers
No eraser.
N
L.4
Pencil sharpeners
No pencil sharpener.
N
L.5
Duplicators and copy machines
No duplicator or copy
machine.
N
L.6
Motor-operated files
No motor-operated file.
N
L.7
Other business equipment
See 1.6.2.
P
M
ANNEX , CRITERIA FOR TELEPHONE RINGING SIGNALS (see
2.3.1)
J
29 - 45
N
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
3
M.1
Introduction
N
M.2
Method A
N
M.3
Method B
N
M.3.1
Ringing signal
N
M.3.1.1
Frequency (f)................................................ :
N
M.3.1.2
Voltage (V) ................................................ :
N
M.3.1.3
Cadence; time (s), voltage (V) ................... :
N
M.3.1.4
Single fault current (mA)............................. :
N
M.3.2
Tripping device and monitoring voltage...... :
N
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N
M.3.2.2
Tripping device
N
M.3.2.3
Monitoring voltage (V)................................ :
N
U
ANNEX , INSULATED WINDING WIRES FOR USE WITHOUT
INTERLEAVED INSULATION (see 2.10.5.4).
N
Separate test report
N
ANNEX , AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N
V
Class III equipment.
V.1
Introduction
N
V.2
TN power systems
N
V.3
TT power systems
N
V.4
IT power systems
N
1.5.1
TABLE: list of critical components
P
Object/part no. Manufacturer/
trademark
Type/model
Technical data Standard
Mark(s) of
conformity1)
Enclosure
Material
Various
HB or better.
UL
Various
30 - 45
UL 94
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
PCB material
--
--
V-1, min.,
105oC
UL 94
UL
AC adaptor
Various
Various
O/P: 5Vdc,
2.5A
EN 60950
TUV (L.P.S.)
1
) an asterisk indicates a mark which assures the agreed level of surveillance
1.6.2
TABLE: electrical data (in normal conditions) Without wireless card
Fuse
#
Irated
(A)
U (V)
P (W)
I (A)
F1
0.5
90V/50Hz
3.90
0.083
Maximum normal load.
F1
0.5
90V/60Hz
3.92
0.084
Maximum normal load.
F1
0.5
100V/50Hz
3.95
0.072
Maximum normal load.
F1
0.5
100V/60Hz
3.95
0.074
Maximum normal load.
F1
0.5
240V/50Hz
4.60
0.052
Maximum normal load.
F1
0.5
240V/60Hz
4.50
0.056
Maximum normal load.
F1
0.5
254V/50Hz
4.70
0.054
Maximum normal load.
F1
0.5
254V/60Hz
4.70
0.052
Maximum normal load.
1.6.2
Ifuse (A) Condition/status
TABLE: electrical data (in normal conditions) With wireless card
Fuse
#
Irated
(A)
U (V)
P (W)
I (A)
F1
0.5
90V/50Hz
5.20
0.10
Maximum normal load.
F1
0.5
90V/60Hz
5.17
0.11
Maximum normal load.
F1
0.5
100V/50Hz
5.16
0.10
Maximum normal load.
F1
0.5
100V/60Hz
5.16
0.10
Maximum normal load.
F1
0.5
240V/50Hz
5.72
0.06
Maximum normal load.
F1
0.5
240V/60Hz
5.74
0.06
Maximum normal load.
F1
0.5
254V/50Hz
5.82
0.06
Maximum normal load.
F1
0.5
254V/60Hz
5.90
0.07
Maximum normal load.
2.1.1.5
TABLE: max. V, A, VA test
P
P
Ifuse (A) Condition/status
N
31 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Voltage (rated) (V)
2.1.1.7
Current (rated)
(A)
Voltage (max.)
(V)
N
TABLE: Hazardous voltage measurement
Location
N
max. Voltage
V peak
Location
2.4.2
Location
2.6.3.3
Location
VA (max.) (VA)
τ calculated τ measured t u→ 0V Comments
(s)
(s)
(s)
Transformer
2.2.2
Current (max.)
(A)
Verdict
TABLE: discharge test
Condition
2.2.2
Result -remark
Voltage Limitation
Component
V d.c.
N
TABLE: SEL voltage measurement
Voltage measured (V) Comments
TABLE: limited current circuit measurement
Voltage
(V)
Current
(mA)
Freq.
(kHz)
N
Limit
(mA)
TABLE: ground continue test
Comments
N
Resistant measured (mΩ) Comments
32 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
2.10.2
Requirement - Test
Peak voltage
(V)
Comments
TABLE: clearance and creepage distance measurements
Up (V)
U r.m.s.
(V)
Required
cl (mm)
cl (mm)
N
Required
dcr (mm)
TABLE: distance through insulation measurements
Distance through insulation di at/of:
4.5
N
RMS voltage
(V)
Clearance cl and creepage
distance dcr at/of:
2.10.5
Verdict
Table: working voltage measurement
Location
2.10.3
and
2.10.4
Result -remark
U r.m.s.
(V)
TABLE: temperature rise measurements
dcr (mm)
N
Test voltage
(V)
Required di
(mm)
di (mm)
With wireless card
test voltage (V) ...................................... : 90V/60Hz

t1 (°C) .................................................... : --

t2 (°C) .................................................... : --

Rise dT of part/at:
dT (K)
Wireless card
U4
P1
33 - 45
Allowed dT
(K)
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
C24
Enclosure outside
T1 coil (Adapter)
T1 core (Adapter)
LF coil (Adapter)
LF core (Adapter)
C3 (Adapter)
Enclosure (Adapter)
Ambient
Temperature rise dT of winding:
4.5
R1 (Ω)
R2 (Ω)
TABLE: temperature rise measurements
dT (K)
allowed
dT (K)
insulatio
n class
With wireless card
test voltage (V) ...................................... : 90V/60Hz

t1 (°C) .................................................... : --

t2 (°C) .................................................... : --

Rise dT of part/at:
dT (K)
Wireless card
38.4
U4
54.5
P1
30.4
C24
32.7
Enclosure outside
15.2
T1 coil (Adapter)
20.1
T1 core (Adapter)
19.1
LF coil (Adapter)
17.6
LF core (Adapter)
16.4
C3 (Adapter)
20.7
4.7
Enclosure (Adapter)
34 - 45
Allowed dT
(K)
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
23.6
Ambient
4.5.2
TABLE: ball pressure test of thermoplastic parts
N
allowed impression diameter (mm) ..............: ≤ 2 mm

Part
4.6.1,
4.6.2
Test temperature
(°C)
Table: enclosure openings
Location
Size (mm)
Comments
None
Side
None
Bottom
None
Condition
5.2
Impression
diameter (mm)
P
Top
5.1.6
Verdict
TABLE: touch current measurement
N
L→ terminal N → terminal Limit (mA) Comments
A (mA)
A (mA)
TABLE: electric strength tests and impulse tests
Test voltage applied between:
N
Test voltage (V)
Supplementary information
35 - 45
Breakdown
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
5.3
Requirement - Test
Result -remark
Verdict
TABLE: fault condition tests
N
ambient temperature (°C) ............................. :

model/type of power supply ......................... :

manufacturer of power supply ..................... :

rated markings of power supply ................... :

No. Component
no.
Fault
Test voltage (V)
Test time Fuse Fuse current Result
no.
(A)
Supplementary information
Note: In fault column, s-c=short-circuited, o-l=over-loaded.
A.6.5
Sample
no./ref.
TABLE: flammable test for classifying materials V-0, V-1 or V-2
Afterflame time (s) t1 or t2
N
Afterflame + afterglow (s) after 2nd flame
application t2 + 3
1/A
2/A
3/A
4/A
5/A
6/B
7/B
8/B
9/B
10/B
Supplementary information:
36 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
Total afterflame time (s) for any condition set t1 + t2 for five (5) specimens:
A.6.6
Sample
no.
TABLE: flammable test for classifying materials V-0, V-1 or V-2
Afterflame time (s) t1 or t2
N
Afterflame + afterglow (s) after 2nd flame
application t2 +t3
11
12
13
14
15
Supplementary information:
Total afterflame time (s) for any condition set t1 + t2 for five (5) specimens:
TABLE: flammability test for classifying foam materials HF-1, HF-2 or
A.7.4,
HBF
A.7.5,
A.7.6 and
A.7.7
Sample
no./ref.
Flame time (s)
Glow time (s)
N
Flaming/glowing
Comment (for A.7.7
distance from he end Burning rate mm/min)
(mm)
1/A
2/A
3/A
4/A
5/A
6/B
7/B
8/B
37 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
9/B
10/B
Supplementary information:
A.7.8
Sample
no.
TABLE: flammability test for classifying foam materials HF-1 or
Flame time (s)
Glow time (s)
Flaming/glowing
distance from the end
(mm)
HF-2
N
Comment
11
12
13
14
15
supplementary information:
A.7.9
Sample
no.
TABLE: flammability test for classifying foam materials HBF
Flame time (s)
Glow time (s)
N
Flaming/glowing
Comment (for A.7.7 distance from the end Burning rate mm/min)
(mm)
11
12
13
14
15
Supplementary information:
38 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
A.8.5
Sample
no.
Requirement - Test
Result -remark
Verdict
N
TABLE: flammable test for classifying materials HB
Flaming/glowing rate (mm/min)
Flaming/glowing distance from reference
mark (mm)
1
2
3
Supplementary information:
A.8.6
Sample
no.
N
TABLE: flammable test for classifying materials HB
Flaming/glowing rate (mm/min)
Flaming/glowing distance from reference
mark (mm)
4
5
6
Supplementary information:
A.9.6
Sample
no./ ref.
N
TABLE: flammability test for classifying materials 5V
Test bars
Flaming + glowing
time (s)
Test plaques
Burning distance
(mm)
Flaming + glowing
time (s)
Burning distance
(mm)


1/A
2/A
3/A
4/A
5/A
39 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Verdict
6/B
7/B
8/B
9/B

10/B

Supplementary information:
A.9.7
N
TABLE: flammability test for classifying materials 5V
Sample
no.
Test bars
Flaming + glowing
time (s)
Test plaques
Burning distance
(mm)
Flaming + glowing
time (s)
Burning distance
(mm)


11
12
13
14
15
Supplementary information:
40 - 45
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
Photo
VIEW 1
VIEW 2
41 - 45
Verdict
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
VIEW 3
VIEW 4
42 - 45
Verdict
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
VIEW 5
VIEW 6
43 - 45
Verdict
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
VIEW 7
VIEW 8
44 - 45
Verdict
Test Report
Test Report No.:CERASH03061001
EN 60 950
Clause
Requirement - Test
Result -remark
VIEW 9
VIEW 10
45 - 45
Verdict
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement