Manual

Add to My manuals
33 Pages

advertisement

Manual | Manualzz

XP3000V

HD Vandal Proof IP Dome Camera User

’s Manual

Version 3.5.0

Welcome

Thank you for purchasing our IP camera!

This user

’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user

’s manual well for future reference! i

Important Safeguards and Warnings

1

Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1.

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2

Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3

Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4

Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5

Environment

This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. ii

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

IPC Unit

Accessories bag

Quick Start Guide

CD

1

1

1

1 iii

Table of Contents

1 General Introduction .................................................................................................................. 1

1.1

Overview ........................................................................................................................ 1

1.2

Features ......................................................................................................................... 1

1.3

Specifications ................................................................................................................ 2

1.3.1

Performance ........................................................................................................... 2

1.3.2

Factory Default Setup ........................................................................................... 4

2 Structure .................................................................................................................................... 11

2.1

Multiple-function Combination Cable ...................................................................... 11

2.2

Framework and Dimension ....................................................................................... 12

2.3

Bidirectional talk.......................................................................................................... 13

2.3.1

Device Connection .............................................................................................. 13

2.3.2

Operation .............................................................................................................. 13

2.4

Alarm Setup ................................................................................................................. 13

3 Installation.................................................................................................................................. 15

3.1

Device Installation ...................................................................................................... 15

3.2

SD Card Installation ................................................................................................... 18

3.3

Lens Adjustment ......................................................................................................... 18

4 Quick Configuration Tool ......................................................................................................... 20

4.1

Overview ...................................................................................................................... 20

4.2

Operation ..................................................................................................................... 20

5 Web Operation .......................................................................................................................... 23

5.1

Network Connection ................................................................................................... 23

5.2

Login and Main Interface ........................................................................................... 23

iv

6 FAQ ............................................................................................................................................ 26

Appendix Toxic or Hazardous Materials or Elements ............................................................... 27

v

1 General Introduction

1.1 Overview

This series IP camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device.

This series uses standard H.264 video compression technology and G.711a audio compression technology, which maximally guarantee the audio and video quality.

This series IPC enclosure has the strong resistance capacity, which can guarantee the proper work performance under heavy strike. It supports real-time monitor and listening at the same time. It supports analog video output and dual-way bidirectional talk.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the network and then use a network client-end. Due to its multiple functions and various uses, this series is widely used in many environments such office, bank, road monitor and etc.

1.2 Features

User

Management

 Different user rights for each group, one user belongs to one group.

 The user right shall not exceed the group right.

Storage

Function

Alarm

Function

Network

Monitor

Network

Management

 Support central server backup function in accordance with your configuration and setup in alarm or schedule setting

 Support record via Web and the recorded file are storage in the client-end PC.

 Support built-in SD card.

 Support local SD card hot swap, support short-time storage when encounter disconnection.

 Real-time respond to external local alarm input and video detect as user predefined activation setup and exert corresponding message in screen and audio prompt(allow user to pre-record audio file)

 Real-time video detect: motion detect, camera masking.

 Can generate an alarm when network abnormal, SD card abnormal event occurred.

 Supports one-channel audio/video data transmit to network terminal and then decode. Delay is within 270ms (network bandwidth support needed)

 Max supports 20 connections.

 Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

 Support web access, widely used in WAN.

 Realize configuration and management via Ethernet.

 Support device management via web or client-end.

 Support various network protocols.

 Support the on-off alarm device to alarm via the sound or the light.

Peripheral

Equipment

Power

Assistant

Function

 External power adapter DC12V/AC 24V

 Support PoE.

 Log function

 Support PAL/NTSC

 Support system resource information and running status real-time display.

1

 Day/Night mode auto switch (ICR switch).

 Built-in IR light. Support IR night vision (For HDBW Series only).

 Backlight compensation: screen auto split to realize backlight compensation to adjust the bright.

 Support electronic shutter and gain setup.

 Support video watermark function to avoid vicious video modification.

1.3 Specifications

1.3.1 Performance

Please refer to the following sheet for performance specification.

Model

Parameter

Main

Processor

OS

TI Davinci high performance DSP

XP3000V

Embedded LINUX

System

Resources

Support real-time network, local record, and remote operation at the same time.

User Interface

Remote operation interface such as WEB, DSS, PSS

System Status

SD card status, bit stream statistics, log, and software version.

Image Sensor

1/2.8-inch CMOS

Pixel

Day/Night

Mode

Auto Iris

2048(H)*1536(V)

Support day/night mode switch and IR-CUT at the same time.

DC drive

Gain Control

Fixed/Auto

White Balance

Manual/Auto

BLC

Electronic

Shutter

Manual/Auto

Manual/Auto

PAL: It ranges from 1/3 to 1/10000.

NTSC: It ranges from 1/4 to 1/10000.

Video

Compression

Standard

H.264/H.264B/MJPEG

Video Frame

Rate

Video Bit Rate

Video Flip

Snapshot

PAL:

Main stream(2048*1536@15fps) extra stream,(704*576@15fps)

Main stream(1920*1080@25fps) extra stream(704*576@25fps)

NTSC:

Main stream(2048*1536@15fps) extra stream(704×480@15fps)

Main stream(1920*1080@30fps) extra stream(704×480@30fps)

H.264: 56Kbps-8192Kbps.

MJPEG is adjustable and bit rate is adjustable.

Support customized setup.

Support mirror.

Support flip function.

Max 1f/s snapshot. File extension name is JPEG.

Privacy Mask

Supports max 4 privacy mask zones

2

Video Setup

Video

Information

Lens

Support parameter setup such as bright, contrast.

Channel title, time title, motion detect, privacy mask.

[email protected]

Lens Interface

CS. Lens is the default accessories

Audio Input

1-channel,RCA audio input.

Audio Output

1-channel, RCA, audio output.

Bidirectional

Talk Input

Reuse the first audio input channel

Audio Bit Rate

16kbps 16bit

Audio

Compression

Standard

G.711A/G.711Mu/PCM

Motion Detect

Video Loss

Alarm Input

396 (18*22) detection zones;sensitivity level ranges from 1 to 6 (The 6 th level has the highest sensitivity)

Activation event, alarm device, audio/video storage, image snapshot, log, email function and etc.

Activation event, alarm device, audio/video storage, image snapshot, log, email function and etc.

2-channel input,1-channel output

Record

Priority

Manual>External alarm >Video detect>Schedule

Local Storage

Support Micro SD card storage

Wire Network

1-channel wire Ethernet port, 10/100 Base-T Ethernet

Network

Protocol

Remote

Operation

Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP, UDP,

SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP,

NFS.

Monitor, system setup, file download, log information, maintenance , upgrade and etc

Video Output

1-channel analog video output,BNC port, 9-pin port connection

Reset

6-pin port connection

IR light

Power

Power

Consumption

Working

Temperature

Working

Humidify

Dimensions(m m)

Weight

Installation

35 LED, IR distance 10 to 20 meters (For HDBW series product only)

Support AC24V/DC12V power. PoE

General series: below 7W.

IR series: below 13W.

-10

℃~+60℃

10%~90%

¢160x118.5

1.25g

Support various installation modes(Enclosure and bracket is optional)

3

1.3.2 Factory Default Setup

Please refer to the following sheet for factory default setup information.

Function

Setup Type

Item

Default setup

XP3000V

Brightness

Contrast

Hue

Saturation

Exposure mode

50

50

50

50

Auto

Gain Scope

Auto Iris

Profile

Day&Night

Backlight

Mirror

Flip

Video bit stream

Main stream

Extra stream

0~80

ON

Auto

Auto

Off

Off

No flip

Bit stream type

Encode mode

General

H.264B

Resolution

1080P(1920*1080)

Frame rate

(FPS)

PAL: 25

NTSC:30

Bit stream type

CBR

Reference bit rate

Bit rate

I frame interval

Watermark settings

Watermark character

Enable

Bit stream type

3584-8192 Kb/S

8192

50

Enable

DigitalCCTV

Enable

General

Encode mode

H.264B

Resolution CIF(352×288/352×240)

Frame rate

(FPS)

PAL: 25

NTSC:30

Bit rate type CBR

4

Function

Setup Type

Item

Snapshot

Overlay

Path

Main stream

Sub(Extra) stream

Network setup

TCP/IP

Reference bit rate

Bit rate

Default setup

XP3000V

192-1024Kb/S

1024

I frame interval

50

Snap type General snap

Image size

1080P(1920*1080)

Quality

Interval

Privacy mask

Better

7s

Enable

Channel title

Time title

Snapshot path

Record path

Enable

Encode mode

Enable

Enable

C:\PictureDownload

C:\RecordDownload

Enable

G.711A

Enable

Encode mode

Disable

G.711A

Host name IPC

Ethernet card

Wire(Default)

Mode

MAC address

Static

Depends on the device

IP version IPV4

IP address 192.168.1.168

Subnet mask

Default gateway

Preferred

DNS

Alternate

DNS

Enable

ARP/Pingto to set IP address

255.255.255.0

192.168.1.1

8.8.8.8

8.8.8.8

Enable

5

Function

Setup Type

Item

service

Connection

PPPoE

DDNS

IP filter

SMTP(email)

Default setup

XP3000V

Max connection

10

TCP port 37777

UDP port 37778

HTTP port 80

RTSP port 554

HTTPs

Enable

Disable

HTTPs port 443

Enable Disable

User name N/A

Password N/A

Server type Disable ,CN99 DDNS

Server IP

Port none

80

Domain name

Update period none

User name none

Password N/A

10m

Trusted sites

SMTP server

Disable none

Port 25

Anonymity Disable

User name anonymity

Password N/A

Sender none

Authenticati on (Encrypt mode)

Title

(Subject)

N/A

IPC Message

Attachment Enable

Main

Receiver

Interval

Health email

N/A

0s

Disable ,interval=60m

6

Function

Setup Type

Item

Event management

UPnP

SNMP

Bonjour

Multicast

WIFI

QoS

Video detect

Default setup

XP3000V

Enable

UPnP

SNMP v1

SNMP v2

Disable

Disable

Disable

SNMP port 161

Read community public

Write community

Trap address private

N/A

Trap port 162

Enable

Server name

Enable

“Device SN”.

Depends on the device.

Multicast address

239.255.42.42

Port 36666

On(Enable) Enable

Real-time monitor

0

Wireless

QoS

Parameter

Disable

Command 0

Enable Disable

Anti-dither 5 seconds

Sensitivity 3

Record

Channel

Enable

Record

Delay

Relay

(Alarm) output

10 seconds

Enable

Alarm delay 10s

Send email Disable

Snapshot Disable

Disable Enable

Record

Channel

Enable

Record

Delay

Relay out

10 seconds

Enable

7

Function

Setup Type

Item

Default setup

XP3000V

Record

Delay

10 seconds

Send email Disable

Alarm setup

Abnormity

Snapshot Disable

Relay output

Enable Disable

Relay input Alarm1

Anti-dither 0s

Sensor type NO

Record channel

Record delay

Relay

(Alarm) output

Relay

(Alarm) delay

Enable

10s

Enable

10s

Send email Disable

Snapshot Disable

(Alarm)

1

Enable

Relay

(Alarm) output

Relay output delay

Disable

Enable

10s

Send email Disable

Enable Disable

Capacity limit (Space threshold)

Relay

(Alarm) output

Relay

(Alarm) output

10%

Enable

Relay output delay

10s

Send email Disable

Enable Disable

Enable

8

Function

Setup Type

Storage management

System management

Item

Destination(Storag e )

Conditions control)

General setup

FTP

(Record

XP3000V

Relay output delay

10s

Send email Disable

Enable

Record

Record delay

Default setup

Disable

Enable

10s

Relay

(Alarm) output

Enable

Relay output delay

Enable

Record

Record delay

10s

Disable

Enable

10s

Relay

(Alarm) output

Relay output delay

Enable

10s

FTP enable Disable

Server IP

Port

N/A

21

User name anonymous

Password N/A

Remote storage path

Emergency storage to local path share

Disable

Pack duration

Record mode

8m

Pre-record 5s

Disk full Overwrite

Auto

Record

Stream

Main Stream

Device

Device SN.

Depends on the device.

9

Function

Setup Type

Item

Auto maintenance

Default setup

XP3000V

name

Language English

Video standard

NTSC

Date format Y-M-D

Time format 24H

Time zone GMT+08:00

Current time

Sync PC

DST

DTS type

Disable

Week

Start time

End time

00:00:00 of the first Sunday of the month

00:00:00 of the second Monday of the month

Synchroniz e with NTP

Disable

NTP server clock.isc.org

Port 37

Update period

10m

Auto reboot Enable 02:00 each day

Auto delete old files

Disable

10

2 Structure

2.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable

information. See Figure 2-1

.

Figure 2-1

Please refer to the following sheet for detailed information.

Port Name Function Connection Note

VIDEO OUT

Video output port

BNC

Output analog video signal. It can connect to the

TV monitor to view the video.

AUDIO IN

AUDIO OUT

LAN

Audio input port

RCA

Audio output port

RCA

Network port

Ethernet port

Input audio signal. It can receive the analog audio signal from the pickup.

Output audio signal to the devices such as the sound box.

 Connect to standard Ethernet cable.

 Support PoE.

I/O I/O port / Includes alarm input and output.

RESET

POWER

Reset button /

Power input port

/

The reset button is to restore device factory default setup.

Power port. Input DC 12V or AC 24V power.

Please connect the DC5.5 round port to 2-pin converter cable when you are using AC 24V power.

11

Please refer to the follow sheet for detailed pin information.

Port Name SN Name Note

1

I/O Port

2

3

4

5

ALARM_COM Alarm output public port.

ALARM_NO

Alarm output port. It is to output the alarm signal to the alarm device.

NO: normal open alarm output port.

ALARM_IN1

ALARM_IN2

Alarm input port 1. It is to receive the on-off signal from the external alarm source.

Alarm input port 2. It is to receive the on-off signal from the external alarm source.

GND Ground port

2.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and

Figure 2-3.

Figure 2-2

12

Figure 2-3

2.3 Bidirectional talk

2.3.1 Device Connection

Before the operation, connect the active pickup to the audio input port of the device. Connect the active speaker to the audio output port of the device. Please make sure the client-end device has the audio input and output function. For example, you need to connect the microphone and then earphone to the

PC if you want to implement the bidirectional talk function.

2.3.2 Operation

Login the Web and click the bidirectional talk button to enable this function. Click this button again; you can close current bidirectional talk.

2.4 Alarm Setup

The alarm interface is shown as in Figure 2-4. Please follow the steps listed below for local alarm input

and output connection.

1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.

2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public port (No.1 pin). The alarm output port supports NO (normal open) alarm device only.

3) Open the Web, go to the Figure 2-4. Please set the alarm input 01 port for the first channel of the I/O

cable (No.3 pin). The alarm input 02 is for the 2 nd

channel of I/O cable (No.4 pin). Then you can select the corresponding type (NO/NC.)

4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the

No.2 pin of the I/O cable.

13

Figure 2-4

14

3 Installation

This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the inceiling installation to realize the hang function. Please refer to the steps listed below.

3.1 Device Installation

Step 1

Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover

and then open the cover. The device is shown as in Figure 3-1

Figure 3-1

Step 2

Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome and

then remove the device pedestal. See

Figure 3-2

.

With IR light Without IR light

Figure 3-2

15

Step 3

Draw out the cable exit and four screw holes in the installation position according to the device pedestal.

Dig the four plastic expansion bolt holes and cable exit. Insert the four plastic expansion bolts into the screw holes

Step 4

Adjust the camera pedestal to the proper position and then draw the cable through the cable exit you just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four plastic expansion bolt holes in the installation position. Put the four self-tapping screws in the device pedestal and then use the screwdriver to secure the screws in the four plastic expansion bolts firmly.

Step 5

Adjust the device position and line up the three inner hexagon screws of the device to the three holes of the installation position. Put the three inner hexagon screws into the screw holes at the bottom of the pedestal. Use the inner hexagon screwdriver to fix firmly. Connect the GND to the ground wires to

improve stability. See Figure 3-3 .

With IR light Without IR light

Figure 3-3

Step 6

Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the steps listed below to adjust. See Figure 3-4.

Please note, for the dome of the IR light, you can skip step a) and step e).

 a): Slightly push the two sides to squeeze the plastic hook so that you can take off the dome enclosure.

 b):Slightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust the module tilt rotation angle (15°~90°).

 c):Slightly loose the screw of the pressing slice, you can adjust the video rotation angle of the module (0°~355°)

 d):Adjust the turning ring of the pedestal, you can adjust the module pan rotation angle (

0°~

355°

).

16

 e): Put the enclose back after you completed the setup.

With IR light Without IR light

Figure 3-4

Please note, the screws in the following figure are the optical adjustment component. Please

make sure it is outward and do not allow it to touch the X-Y-Z axis module. See Figure 3-5

Figure 3-5

Step 7

Put the dome cover back and then put the three inner hexagon screws into the holes of the device. Use

the inner hexagonal wrench to fasten these three screws. See Figure 3-6

Figure 3-6

17

3.2 SD Card Installation

Important

Before you install the SD card, please unplug he power cable to shut down the device!

First, please refer to the step1 in the chapter 3.1 to open the device.

Second, please adjust the proper position to install the SD card.

Last, please refer to the step 7 in the chapter 3.1 to complete the installation. See Figure 3-7.

With IR light Without IR light

Figure 3-7

3.3 Lens Adjustment

Step 1

Slightly loose the screw B manually and then turn the screw B slowly. Adjust the lens focus distance to

the proper position according to the monitor video. See Figure 3-8.

Step 2

Use the flat screwdriver to loose the screw A slightly and then turn the Screw A slowly. Adjust the lens focus to get the clear video and then use the flat screwdriver to secure the screw firmly.

Step 3

When you are adjusting the screw A, the video may becomes blur. Please slightly adjust the screw B manually to get the vivid video. Finally fix the screw.

18

With IR light Without IR light

Figure 3-8

19

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.

In the device list interface, you can view device IP address, port number, subnet mask, default gateway,

MAC address and etc.

Figure 4-1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.

Figure 4-2

20

Select the

“Open Device Web” item; you can go to the corresponding web login interface. See Figure

4-3.

Figure 4-3

If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set.

In the configuration tool search interface (Figure 4-1), please select a device IP address and then double

click it to open the login interface. Or you can select an IP address and then click the Login button to go

to the login interface. See Figure 4-4.

In Figure 4-4, you can view device IP address, user name, password and port. Please modify the

corresponding information to login.

Please note the port information here shall be identical with the port value you set in TCP port in Web

Network interface. Otherwise, you can not login the device.

If you are use device background upgrade port 3800 to login, other setups are all invalid.

Figure 4-4

21

After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.

Figure 4-5

22

5 Web Operation

This series IPC product support the Web access and management via PC.

Web includes several modules includes monitor channel preview, PTZ control, system configuration, alarm and etc.

IP camera factory default setup:

 IP address: 192.168.1.108.

 User name: admin

 Password: admin

5.1 Network Connection

Please follow the steps listed below for network connection.

 Make sure the IPC has connected to the network properly.

 Please set the IP address, subnet mask and gateway of the PC and the IPC respectively. IPC default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is 192.168.1.1

 Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.

5.2 Login and Main Interface

Open IE and input IP camera address in the address bar.

For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address

bar. See Figure 5-1.

Input your IP address here

Figure 5-1

The login interface is shown as below. See Figure 5-2.

Please input your user name and password.

Default factory name is admin and password is admin.

Note: For security reasons, please modify your password after you first login.

23

Figure 5-2

If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab

or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too.

If you can

’t download the ActiveX file, please check whether you have installed the plug-in to disable the

control download. Or you can lower the IE security level. See Figure 5-3.

24

Figure 5-3

After you logged in, you can see the main window. See Figure 5-4.

Figure 5-4

Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.

25

6 FAQ

Bug

I can not boot up the device.

Please click RESET button for at least five seconds to restore factory default setup.

SD card write times

Do not set the SD card as the storage media to storage the schedule record file. It may damage the SD card duration.

I can not use the disk as the storage media.

When disk information is shown as hibernation or capacity is 0, please format it first (Via Web).

I can not upgrade the device via network.

When network upgrade operation failed, you can use port 3800 to continue upgrade.

Recommended SD card brand

Kingston 4GB, Kingston 1GB, Kingston 16GB, Transcend

16GB, SanDisk 1G, SanDisk 4G.

Usually we recommend the 4GB (or higher) or industry-level high speed card in case the slow speed results in data loss.

Audio function

The lightproof ring of the IR device

Please use active device for the audio monitor input, otherwise there is no audio in the client-end.

The lightproof ring of the IR device lens is the necessary component when it works. You can not view the clear video when the IR light is on if you remove the lightproof ring.

26

Appendix Toxic or Hazardous Materials or Elements

Toxic or Hazardous Materials or Elements

Component

Name

Pb Hg Cd Cr VI PBB PBDE

Circuit Board

Component

○ ○ ○ ○ ○ ○

Device

Construction

Material

○ ○ ○ ○ ○ ○

Wire and Cable

○ ○ ○ ○ ○ ○

Packing

Components

Accessories

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer is not authorized to process such kind of substances or elements, please return to the corresponding local authorities to process according to your local government statutes。

Note

This user

’s manual is for reference only. Slight difference may be found in user interface.

All the designs and software here are subject to change without prior written notice.

If there is any uncertainty or controversy, please refer to the final explanation of us.

Please visit our website for more information.

27

advertisement

Related manuals